Dimensions
TC-20 The TC-20 tracked crusher has the largest hopper in its class and is built for big loads and even bigger production. IROCK s TC-20 produces a uniform, cubical product that will increase your bottom line. Features A 15-cubic-yard fixed Hardox hopper is paired with a 52-inch by 16-foot vibrating grizzly feeder with a larger crusher inlet for increase production rates. The TC-20 s feeder is the longest among tracked crushers and allows operators to feed material with a large wheel loader. A 48-inch-wide discharge conveyor can stockpile up to a maximum height of 10-feet, 11-inches. Operators can hydraulically lower or raise the conveyor to feed stockpiling conveyors and make maintenance easier. The standard ROCK BOX reduces wear on the discharge point by forming crushed material into a natural rock shelf to serve as a liner. A standard wireless remote control offers standard full plant functions and two-speed tracking for easy maneuverability around a job site or onto a trailer. Specifications GENERAL MODEL TC-20 SHIPPING DIMENSIONS LENGTH 57' 8-15/16" WIDTH 11' 8-7/16" HEIGHT 12' 4-13/16" WEIGHT 98,500 lbs OPERATING DIMENSIONS
LENGTH 57' 7" WIDTH 17' 3" HEIGHT 12' 7" POWER ENGINE ENGINE HP CLUTCH FUEL TANK CAPACITY HYDRAULICS - PLANT SYSTEM #1 CAT C-13 ACERT DIESEL, "C" INTERMITTENT DUTY, (Tier 3) EMISSIONS APPROVED 440 HP HPTO 12 HYDRAULICALLY APPLIED DRY CLUTCH 140 GALLONS SYSTEM #1 OPERATES THE FEEDER, RIGHT TRACK, LEFT TRACK, MAIN CONVEYOR, SIDE CONVEYOR, MAGNET BELT, AND CRUSHER DOOR. SYSTEM #1 IS DRIVEN OFF TWO PUMPS MOUNTED ON THE CAT C13 SAE No 1 FLYWHEEL HOUSING. DUEL REAR PTO OPERATES AT 1.3 TIMES ENGINE SPEED WITH SAE "C" 14T 12/24 DP SPLINE SHAFT INPUT. SYSTEM #2 HYDRAULIC TANK CAPACITY HYDRAULIC OIL PUMPS - SYSTEM #1 GPM - SYSTEM #1 MAXIMUM PSI - SYSTEM #1 FEEDER MOTOR MAIN CONVEYOR MOTOR SYSTEM #2 SUPPLIES HYDRAULIC POWER TO THE CLUTCH, GALTECH VALVE, AND THE COOLING RADIATOR. THE GALTECH VALVE OPERATES THE OPTIONAL MAIN CONVEYOR FOLD, SIDE CONVEYOR FOLD, UPPER APRON ADJUST, LOWER APRON ADJUST AND ALSO CONTAINS A CHECK VALVE FOR HEATING THE OIL WHEN IT IS BELOW THE SETPOINT. PUMP DRIVE ROTATES SAME DIRECTION AS CRANKSHAFT AT 1.14 TIMES ENGINE SPEED WITH SAE"B" 13T 16/32 DP SPLINE SHAFT INPUT. 80 GALLONS CASTROL DUAL RANGE HV 46 (ISO 46) OR EQUIVALENT TWO (2) DANFOSS SERIES 45 J-FRAME OPEN CIRCUIT, VARIABLE PISTON PUMPS. 45CC/REV PER PUMP. (2.75 CU IN/REV PER PUMP) 55.6 GPM AT 1800 RPM AND 64.8 GPM AT 2100 RPM 4495 PSI ( 310 BAR) CONTINUOUS RINEER SERIES 15 VANE MOTOR - 5 CU IN/REV (82 CC/REV) - 8.7 GPM AT 400 RPM TO 17.3 GPM AT 800 RPM. MAX PRESSURE 3000 PSI (207 BAR) CONTINUOUS. SAE 14 T 12/24 PITCH SHAFT DANFOSS ORBITAL MOTOR - 38.4 CU IN/REV (629 CC/REV) - 12.1 GPM AT 325 FPM. MAX PRESSURE 2900 PSI (200 BAR) CONTINUOUS, 3630 PSI (250 BAR) INTERMITTANT, 4350 PSI (300 BAR) PEAK. 1-1/2" DIA STRAIGHT KEYED SHAFT
SIDE CONVEYOR MOTOR MAGNET BELT MOTOR TRACK MOTOR PUMP - SYSTEM #2 MAXIMUM PSI - SYSTEM #2 GPM - SYSTEM #2 LOW TEMPERATURE SET POINT RECOMMENDED OPERATING TEMPERATURE HYDRAULIC FLUID CHANGE INTERVALS REQUIRED CLEANLINESS CLASS DANFOSS ORBITAL MOTOR - 7.6 CU IN/REV (125 CC/REV) - 3.9 GPM AT 400 FPM. MAX PRESSURE 3050 PSI (210 BAR) CONTINUOUS, 3990 PSI (275 BAR) INTERMITTANT, 4280 PSI (295 BAR) PEAK1-1/4" DIA STRAIGHT KEYED SHAFT DANFOSS ORBITAL MOTOR - 7.6 CU IN/REV (125 CC/REV) - 3.9 GPM AT 400 FPM. MAX PRESSURE 3050 PSI (210 BAR) CONTINUOUS, 3990 PSI (275 BAR) INTERMITTANT, 4280 PSI (295 BAR) PEAK1-1/4" DIA STRAIGHT KEYED SHAFT KAYABA TWO SPEED MOTOR OPERATES AT 3.0 CU IN/REV (49.9 CC/REV) AT LOW SPEED AND 5.2 CU IN/REV (85.9 CC/REV) AT HIGH SPEED. MAXIMUM FLOW PER TRACK IS 25.3 GPM PER PUMP IN LOW OR HIGH SPEED. TUROLLA D-SERIES GEAR PUMP 1.37 CU IN/REV (22.51 CC/REV) 4000 PSI (276 BAR) CONTINUOUS 12.1 GPM AT 1800 RPM AND 14.2 GPM AT 2100 RPM 60 DEG F. (ADJUSTABLE THROUGH PLUS+1 CONTROLLOR ONLY ) 86 DEG F TO 140 DEG F (30 DEG C T0 60 DEG C) FIRST CHANGE: 500 HOURS AFTER START-UP. 2000 HOURS OR ONCE A YEAR AFTERWARDS. NOTE: FLUID SAMPLES ARE THE BEST DETERMINATION FOR SUITIBILITY OF CONTINUED USE OF HYDRAULIC FLUIDS UNDER EXTREME OPERATING CONDITIONS. 18/16/13 (ISO 4406-1999) MAGNET/CHUTE MODEL MSI BELT WIDTH 36" MAIN DISCHARGE CONVEYOR BELT WIDTH 48" BELT TYPE 3-PLY 330 PIW CONVEYOR LENGTH 42' 3-13/16" HEAD TYPE HEAD DIMENSIONS TAIL TYPE TAIL DIMENSIONS BEARINGS TYPE - HEAD DRUM WITH 1/2" LAGGING 16" DIA X 51" FACE WIDTH WING 12" DIA X 51" FACE WIDTH BALL BEARING 2-BOLT PILLOW BLOCK
BEARING SIZE - HEAD BEARINGS TYPE - TAIL BELT CLEANER 3-7/16" DIA 2-15/16" BALL BEARING 2-BOLT PILLOW BLOCK DRIVE TYPE ORBITAL MOTOR - TMT 630 IDLERS RETURN IDLERS SIDE FINES CONVEYOR BELT WIDTH 24" BELT TYPE 48" PRIMARY BELT CLEANER WITH PIT VIPER BLADE - TWIST TENSIONER CEMA B, 5"DIA CANS X 48" BELT WIDTH CEMA B, 5" DIA CANS X 48" BELT WIDTH 2-PLY 220 PIW CONVEYOR LENGTH 13' 11-7/8" HEAD TYPE HEAD DIMENSIONS TAIL TYPE TAIL DIMENSIONS BEARINGS TYPE - HEAD BEARING SIZE - HEAD BEARINGS TYPE - TAIL BEARING SIZE - HEAD BELT CLEANER DRIVE TYPE IDLERS RETURN IDLERS HOPPER TYPE DRUM WITH 1/2" LAGGING 12" DIA X 26" FACE WIDTH WING 8" DIA X 26" FACE WIDTH BALL BEARING 2-BOLT PILLOW BLOCK "2-7/16" DIA BALL BEARING 2-BOLT PILLOW BLOCK 1-15/16" DIA 24" PRIMARY BELT CLEANER OMS 125 HYDRAULIC MOTOR CEMA B, 4" DIA CANS X 24" BELT WIDTH CEMA B, 4"DIA CANS X 24" BELT WIDTH SKID OVERALL DIMENSIONS (INCLUDES LEGS) HOPPER DIMENSIONS 8' 10-1/4"(W) X 206-3/16"(L) X 5' 1-11/16"(H) 8' 10-1/4"(W) X 206-3/16"(L) X 2' 10-3/8"(H)
CAPACITY (LEVEL) 9 CUBIC YARDS FEEDER TYPE VIBRATING GRIZZLY FEEDER DRIVE TYPE DIRECT DRIVE HYDRAULIC VANE MOTOR WIDTH 52" LENGTH 16' CRUSHER CRUSHER TYPE HORIZONTAL IMPACT CRUSHER CRUSHER SERIES 4056 NO. OF BLOW BARS 2 BLOW BARS, 2 DUMMY BARS FEED OPENING 56" X 32" NO. OF APRONS (3) THREE - (2) TWO ADJUSTABLE OAND (1) ONE FIXED TRACK SPECS LENGTH (CENTER) 12' 5-9/16" (3800 mm) SHOE WIDTH 19.7 INCHES (500 mm) DRIVE TWO SPEED DRIVE - 0.68 MPH LOW SPEED - 1.2 MPH HIGH SPEED GEARBOX BONFIGLIOLI T710K PLANETARY GEARBOX; 1:123 REDUCTION RATIO PERFORMANCE TRAVEL SPEED 0.68 MPH IN LOW SPEED AND 1.2 MPH IN HIGH SPEED OPTIONS 48" X 36" CROSS BELT MAGNET, FRAME AND CHUTE KIDNEY LOOP HYDRAULIC OIL FILTERING SYSTEM REAR HYDRAULIC STABILIZING LEGS FRONT HYDRAULIC STABILZING LEGS PT TECH EXTENDED WARRANTY OTHER DUST SUPPRESSION ELECTRICAL REMOTE CONTROL H2O SPRAY SYSTEM WITH TWO SPRAY BARS. ONE SPRAY BAR AT THE CRUSHER INLET AND ONE AT THE CRUSHER OUTLET. HBC REMOTE WITH PLUS+1 CONTROLLER
Revision date: January 1, 2014