product guide features 36 mton (50 ton) Capacity 539 mton-m (3,900 ft-kips) Maximum oad Moment 76, m (50') eavy-ift 85,3 m (80') Fixed Jib on eavy-ift 00,6 m (330') uffing Jib 53 kw (340 P) engine 8,9 m (390') Fixed Jib on uffing Jib EPIC controls with Can-Bus technology 30 m/min (45 fpm) line speed standard 47 kn (33,000 lb) line pull standard,300 kg (5,000 lb) Clamshell capacity Fast, efficient self-assembly and disassembly ships on only 8 trucks All modules meet US weight and European width requirements Manitowoc Crane CARE comprehensive support contents Specifications 3 Outline Dimensions 6 Transport Data Performance Data 4 Combinations 0 Main Range / oad Charts 3 Fixed Jib Range / oad Charts 7 uffing Jib Range / oad Charts 30 Fixed Jib on uffing Jib Range / oad Charts 34 Crane CARE 38 www.manitowoccranegroup.com
notes
specifications Upperworks Engine Cummins Model QS T3 diesel, 6 cylinder, 53 kw (340 BP) @ 800 governed RPM. Includes engine block heater, disconnect clutch for cold weather starting, high silencing muffler, hydraulic oil cooler, radiator and fan. Multiple hydraulic pump drive transmission provides power for all machine functions. Two volt maintenance-free batteries, 300 CCA at - 8 C (0 F), 4 volt system and 00 amp alternator. One diesel fuel tank, 586 l (55 gal.), with level indicator in operator s cab. Optional: Cold-weather package with heater for fluids, and computer display. Controls Modulating electronic-over-hydraulic controls provide infinite speed response directly proportional to control lever movement. Controls include Manitowoc's exclusive EPIC Electronically Processed Independent Control system with CAN-BUS technology providing microprocessor driven control logic, pump control, on-board diagnostics, and service information. Travel and swing alarms are standard. Block-up limit control is standard for hoist and whip lines. Each function is equipped with relief valves to protect the hydraulic circuit from overload or shock. System includes oil cooler and replaceable, full flow filter. All oil is filtered before entering the hydraulic pumps. ydraulic system also includes pump transmission disconnect and hydraulic oil cooler. Drums Two equal width drums, 676 mm (6-5/8") wide and 539 mm (-/4") diameter are driven by independent variable displacement axial piston hydraulic motors through planetary reduction mounted on separate front and rear shafts with anti-friction bearings. Drums are grooved for 8 mm wire rope. Powered hoisting/lowering operation is standard with automatic (spring applied, hydraulically released) multidisc brakes, and drum rotation indicators.. Optional: free-fall operation for front and/or rear drum(s). Wet disc brake manually applies by foot pedal with locking latch in operator s cab. Operator may select free-fall or powered lowering mode using a selector switch. Optional: auxiliary (third) hydraulic powered drum rated 47 kn (33,000 lb) line pull mounted in boom butt. Includes third drum control system. Optional: auxiliary (third) hydraulic powered drum rated 89 kn (0,000 lb) line pull mounted in boom butt. Includes third drum control system. Optional: auxiliary drum preparation includes electric wiring, controls, hydraulic pump and plumbing. 3 Integrated oad Moment Indicator system (MI) is standard for main boom and upper boom point. Function cut-out or warning only operation is selected via a keyed switch on the MI console. Optional: Anemometer (wind indicator). Optional: Foot control for travel. ydraulic System Six high-pressure piston pumps, driven by a multi-pump transmission, provide independent closed-loop hydraulic power for the hoisting drums, boom hoist, swing, left crawler and right crawler. ydraulic reservoir capacity is 469 l (4 gal.) and is equipped with breather, clean out access, and internal diffuser. oist Independent boom hoist consists of a 5 mm (9.9") wide and 483 mm (9") diameter drum lagged for mm diameter wire rope. Includes m (75') of mm wire rope for 6-part line reeving. Drum is powered by a variable-displacement hydraulic motor coupled to an integral brake and planetary reduction gearbox. Ratcheting pawl and rotation indicator are standard. hoist speed: raise 76, m (50') full main boom from 0º- 8º in minute, 55 seconds. Swing System
specifications 4 igh strength fabricated steel rotating bed is mounted on 46 mm (7'-/") diameter single-row ball bearing turntable. Independent swing powered by one fixed displacement hydraulic motor coupled to a planetary reduction gearbox with internal brake. Swing system maximum speed:.8 rpm. Support System Moving Mast is 6,7 m (3') long and connects the boom hoist reeving to the steel boom suspension strap rigging. When used with the optional self-erect package, the mast is used for crane assembly and disassembly. It is capable of lifting and positioning the crawler assemblies, stacking the counterweights, and assembling the boom and jib. Spring cushioned boom stop and automatic boom stop are standard. Counterweight Counterweight tray and counterweights for the upperworks is raised by a pair of cylinders and lifting chain. Counterweight attaches to the rotating bed with power actuated pins. UNIT WEIGT TOTA WEIGT QTY. ITEM kg lb kg lb Upperworks Tray 7 80 7,00 7 80 7,00 4 Upper Box 6 3 3,500 4 49 54,000 Pins. links, etc. 37 37 37 300 SERIES TOTA 3 430 7,500 Upperworks Upper Box 6 3 3,500 50 7,000 Carbody ower Box 9 980,000 9 960 44,000 Optional: Add to SERIES for SERIES TOTA 65 640 4,500 Vision Operator s Cab Fully enclosed and insulated steel module mounted at left front corner of rotating bed on a pivoting frame that permits cab to be repositioned for transportation. Module is equipped with sliding door, large safety glass windows on all sides and roof. Signal horn, cab space heater, front and roof windshield wipers, dome light, sun visor and shade, fire extinguisher, air conditioning, and radio are standard. Optional: Nylon protective window covers. owerworks Carbody Connects rotating bed to crawler assemblies. igh strength fabricated steel assembly with FACT connection system for fast installation and removal of crawler assemblies. Crawlers Crawler assemblies are 7,4 m (3' 9") long with, m (48") wide cast steel crawler pads and sealed intermediate rollers. Each crawler is identical and can be mounted on either side of the carbody. Each crawler is powered independently by a variable displacement hydraulic motor and includes a hydraulically powered pin actuator for fast installation and removal from carbody. Carbody mounted drive motors are connected to crawler final reduction via drive shaft with guard. Crawlers provide ample tractive effort for counter rotation with full rated load. Maximum ground speed of,8 kph (. mph). Optional: Self-erect system includes two sheaves for crawler, counterweight, and boom handling, jacking cylinders with pads, 7-mton (30-ton) assembly block, and crawler handling chains. Attachments No. 84 eavy-ift The liftcrane is equipped with 5, m (50') of No. 84 basic heavy-lift angle chord boom consisting of a 6,7 m (') butt and 8,5 m (8') top with four 76, cm (30") diameter roller bearing sheaves on one shaft. Includes MI hardware, rope guides, boom hoist wire rope, boom angle indicator, and 3,6 mton (5 ton) swivel hook and weight ball. The No. 84 boom utilizes steel suspension straps and Manitowoc s patented, exclusive FACT connection system. Powered boom hinge system including cylinder, piping, operating controls, and locking device standard. uffing jib preparation included as standard. Optional 3,0 m (0'), 6, m (0'), and, m (40') No. 84 boom inserts with steel boom suspension straps and FACT connection system. Utilize main boom inserts in combination with No. 84
specifications basic main boom for total length up to 76, m (50'). Optional No. 84 detachable upper boom point with one 76, cm (30") diameter tapered roller bearing steel sheave grooved for 8 mm rope with rope guard for liftcrane. Optional open throat top No. 84-38' with FACT connection system. No. 34 Fixed Jib Optional No. 34 basic fixed jib 9, m (30') length consisting of 4,6 m (5') jib butt and 4,6 m (5') jib top with 3,7 m (') jib strut, pendants, and backstay. Includes MI hardware. For use with No. 84 boom. Optional No. 34 fixed jib inserts 3,0 m (0') and 6, m (0') with pendants. Utilize fixed jib inserts in combination with the No. 34 basic fixed jib for total lengths of to 4,4 m (80'). Note: Jib lengths greater than 8,3 m (60') require the use of at least one 6, m (0') No. 34 fixed jib insert. No. 55 uffing Jib Optional 8,3 m (60') basic No. 55 luffing jib assembly with MI hardware consisting of 8, m (7') jib butt, 3,0 m (0') insert, and 7,0 m (3') jib top with two 68,6 cm (7") straight roller bearing sheaves, boom cap with 5,6 m (8.5') fixed strut and 5,6 m (8.5') jib strut, pin connected boom sections, pendant rigging, backstay pendants, jib point wheel, and 8 mm luffing jib hoist line. Optional 3,0 m (0'), 6, m (0'), and, m (40') No. 55 luffing jib inserts with pendant suspension. Optional, m (40') insert with intermediate fall and pendant suspension. Utilize luffing jib inserts in combination with the No. 55 basic luffing jib for total lengths up to m (60'). Utilize fixed jib inserts in combination with the No. 38A basic fixed jib extension for a total length up to 8,3 m (60'). Optional Equipment Optional: Blocks and ooks, each with rollerbearing sheaves for 8 mm wire rope, a roller-bearing swivel hook, a hook latch and a swivel lock. 3,6 mton (5 ton) swivel hook and weight ball 7, mton (30 ton) hook block with single roller bearing sheave and roller bearing swivel hook with hook latch and swivel lock (assembly block) 90,7 mton (00 ton) hook block with three roller bearing sheaves and roller bearing swivel hook with hook latch and swivel lock 36 mton (50 ton) hook block with four roller bearing sheaves and roller bearing swivel hook with hook latch and swivel lock Optional: ydraulic Test Kit: required to properly analyze the performance of the EPIC control system. Optional: Service Interval Kits for the regularly scheduled maintenance of general crane operations. Optional: ighting Packages: consult dealer for available options. Optional: Special Paint [color(s) other than Manitowoc standard red and black]. Optional: Custom vinyl decal(s) of customer name and/or logo from artwork supplied by customer. Optional: Export Packaging: basic crane, boom and jib sections. 5 No. 38A Fixed Jib Extension Optional 9, m (30') No. 38A basic fixed jib extension consisting of a 4,6 m (5') jib butt and 4,6 m (5') jib top with 5,4 m (8') jib strut, pendants, jib stop, backstay, wheel, and mounting parts. Includes MI hardware. For use with No. 55 luffing jib. Optional No. 4 fixed jib 3,0 m (0') inserts with pendants.
6 outline dimensions 6,99 m (' ") MAST TAISWING ROTATION 0,85 m (35' 7") 8,46m (7' 9") BOOM INGE 3,60 m (' 0"),4 m (4' ") 5,38 m (7' 8") 5,50 m (8' ") TAISWING 7,3 m (4' 0") 9,05 m (9' 8") 6,7 m (0' 7"),5 m (5' 0"),85 m (6' ") 4,97 m (6' 4"),95 m (9' 8") 4,03 m (3' 3") SERIES (0' 3,9 6") m SERIES 3,60 m (' 0"),05 m (3' 5") 3,56 m (' 8") 0,37m (' 3"),0 m (3' ") 5,9 m (9' 5") 0,36 m (' ") 6,67 m (' ") 0,37m (' 3")
outline dimensions Basic Crane ength 0,03 m 3' " Width 3,00 m 9' 0" eight 3,38 m 0' 9" Weight 37 665 kg 83,40 lb 7 Note: Weight includes carbody, upperworks, operator s cab, mast, boom-hoist wire rope, maximum hoist and whip lines on drums, front counterweight, optional self-assembly jacks, full hydraulic fluid reservoir, and half tank of fuel. Crawlers x ength 7,3 m 4' " Width,9 m 7' 6" eight,5 m 4' " Weight 4 69 kg 3,30 lb Note: Width is based on platform in stowed position. Crawler is,0 m (3' "). Counterweight Tray x ength 4,98 m 6' 4" Width,45 m 4' 9" eight 0,5 m ' 8" Weight 7 80 kg 7,00 lb Carbody Counterweight x ength,90 m 6' 3" Width,57 m 5' " eight 0,7 m ' 4" Weight 9 979 kg,000 lb Upper Counterweight Series x 4 Series x 6 ength,35 m 4' 5" Width, m 3' 8" eight 0,97 m 3' " Weight 6 3 kg 3,500 lb Option
8 outline dimensions No. 84 Butt 6,7 m (') & Wire Rope Guide, Stop x ength 6,8 m ' 4" Width,05 m 6' 9" eight,0 m 6' 7" Weight 680 kg 5,935 lb Note: Includes boom butt support for self-erect option and boom angle indicator. No. 84 Top 8,5 m (8') & Wire Rope Guide, Straps x ength 8,97 m 9' 6" Width,05 m 6' 9" eight,64 m 8' 9" Weight 3 686 kg 8,30 lb Note: Wire rope guide shown in stowed position. No. 84 Main 3,0 m (0') Insert & Straps x, ength 3,3 m 0' 7" Width,08 m 6' 0" eight,9 m 6' 3" Weight 578 kg,80 lb No. 84 Main 6, m (0') Insert & Straps x ength 6,7 m 0' 7" Width,08 m 6' 0" eight,9 m 6' 3" Weight 94 kg,080 lb No. 8 Main, m (40') Insert & Straps x,, 3, 4 ength,37 m 40' 7" Width,08 m 6' 0" eight,9 m 6' 3" Weight 560 kg 3,665 lb Option
outline dimensions No. 84 Open Throat Top,6 m (38') & Wire Rope Guide, Straps x ength,34 m 40' 6" Width,08 m 6' 0" eight,39 m 7' 0" Weight 3 347 kg 7,378 lb 9 Note: Wire rope guide shown in shipping position. No. 34 Jib Butt 4,6 m (5') & Strut, Stop x ength 4,67 m 5' 4" Width 0,86 m ' 0" eight,9 m 4' 3" Weight 635 kg,400 lb No. 34 Jib Top 4,6 m (5') & Pendants x ength 4,93 m 6' " Width 0,79 m ' 7" eight 0,79 m ' 7" Weight 553 kg,0 lb No. 34 Jib Insert 3,0 m (0') & Pendants x ength 3,0 m 0' 6" Width 0,79 m ' 7" eight 0,79 m ' 7" Weight 8 kg 480 lb No. 34 Jib Insert 6, m (0') & Pendants x, ength 6,7 m 0' 3" Width 0,79 m ' 7" eight 0,79 m ' 7" Weight 340 kg 750 lb No. 84 Upper Point x ength,64 m 8' 8" Width 0,4 m ' 4" eight 0,8 m ' 8" Weight 54 kg,35 lb Note: Includes mounting bracket Option
outline dimensions 0 No. 55 uffing Jib 00,0m (00') Cap, Butt, Struts, Guides, Straps, Pendants x ength 0,80 m 35' 5" Width,08 m 6' 0" eight 3,05 m 0' 0" Weight 4 754 kg 0,480 lb Note: Shown in shipping position. No. 55 Jib Top 7,0 m (3') Guides & Pendants x ength 7,75 m 5' 5" Width,5 m 5' 0" eight,5 m 7' " Weight 803 kg 3,975 lb No. 55 Jib Insert 3,0 m (0') Insert & Pendants x ength 3,5 m 0' 4" Width,5 m 5' 0" eight,37 m 4' 6" Weight 38 kg 84 lb No. 55 Jib Insert 6, m (0') Insert & Pendants x ength 6,0 m 0' 4" Width,5 m 5' 0" eight,37 m 4' 6" Weight 6 kg,349 lb No. 55 Jib Insert, m (40') Insert & Pendants x, ength,9 m 40' 4" Width,5 m 5' 0" eight,37 m 4' 6" Weight 05 kg,36 lb No. 55 Jib Insert, m (40') Intermediate Fall, Insert & Pendants x ength,9 m 40' 4" Width,5 m 5' 0" eight,4 m 4' 8" Weight 64 kg 3,67 lb Option
outline dimensions No. 38A Jib Butt 4,6 m (5') & Strut, Stop x ength 5,64 m 8' 6" Width 0,79 m ' 7" eight 0,94 m 3' " Weight 39 kg 87 lb No. 38A Jib Top 4,6 m (5') Roller & Pendants x ength 5,69 m 8' 8" Width 0,76 m ' 6" eight 0,7 m ' 4" Weight 359 kg 79 lb No. 38A Jib Insert 3,0 m (0') & Pendants x, ength 3, m 0' 3" Width 0,76 m ' 6" eight 0,58 m ' " Weight 98 kg 0 lb W ook block for 8 mm or (-/4") wire rope Capacity 36 mt 50 t ength,03 m 7' 6" Weight 84 kg 4,000 lb Width 0,86 m ' 0" Capacity 9 mt 00 t ength,98 m 6' 6" Weight 769 kg 3,900 lb Width 0,89 m ' " Capacity 4 mt 45 t ength,83 m 6' 0" Weight 79 kg,600 lb Width 0,9 m 3' 0" W Self Assembly ook block for 8 mm or (-/4") wire rope Capacity 7 mt 30 t ength,7 m 3' 0" Weight 680 kg,500 lb Width 0,64 m ' " D Weight Ball Capacity/Swivel 3,6 mt 5 t Diameter 0,56 m ' 0" Weight 594 kg 30 lb ength,07 m 3' 6" Option
transport data Trailer oad Out Summary Model 555 Series No. 34 Fixed Jib 4,4 m (80') and No. 84 76, m (50') Item Weight Quantity on each Item Trailer oad # Trailer oad # kg (lb) * 3* 4** 5 6 7 8 No. 555 Basic Crane &Front Counterweight 37 665 (83,40) Crawler Assembly 4 69 (3,30) Counterweight Tray 7 80 (7,00) Upper Counterweight 6 3 (3,500) ower Carbody Counterweight 9 979 (,000) 6,7 m (') No. 84 Butt 597 (5,730) 8,5 m (8') No. 84 Top 3 686 (8,30) 3,0 m (0') 578 (,80) 6, m (0') 94 (,080), m (40') *** 560 (3,665) 0,0 m (30') No. 34 Jib & Strut 3,0 m (0') No. 34 Jib Insert 6, m (0') No. 34 Jib Insert 88 (,60) 8 (480) 340 (750) 36 mton (50 ton) ook Block 84 (4,000) 7 mton (30 ton) Self-assembly Block 680 (,500) 3,6 mton (5 ton) Weight Ball No. 84 Upper Point 594 (,30) 54 (,35) Approximate Total Shipping Weight kg (lb) 37 665 (83,40) 6 79 (35,895) 6 79 (35,895) 09 (6,50) 7 (36,40) 5 60 (34,665) 8 770 (4,60) 8 46 (40,630) * Drop deck trailer recommended. ** Step deck trailer recommended. *** One insert includes jib backstay lugs. oad weights do not include blocking, miscellaneous items. Complies with all European 3,0 m width restrictions for shipping.
assembly 3
performance data 4 Wire Rope engths No. 84 - or - Open Throat Top on No. 84 - or - Fixed Jib No. 34 on No. 84 Whip ine oist line or and Fixed Jib ength Front or Aux Drum ( Part of ine) Front or Aux Drum ( Parts of ine) m Rear Drum (ft) Maximum Required Parts of ine *5, (50) 43 (40) 64 (0) 77 (580) 9 8,3 49 73 (40) 07 (680) 9,3 55 8 38 (780) 9 4,4 6 (00) 9 (300) 44 (800) 8 7,4 67 (0) 0 (330) 68 (880) 8 30,5 (00) 73 (40) 0 (360) 68 (880) 7 33,5 (0) 79 (60) 9 (390) 87 (940) 7 36,6 (0) 85 (80) 8 (40) 87 (940) 6 39,6 (30) 9 (300) 37 (450) 93 (960) 6 (40) 98 (30) 46 (480) 93 (960) 5 45,7 (50) 04 (340) 5 (500) 93 (960) 5 0 (360) 6 (530) 93 (960) 4 5,8 6 (380) 7 (560) 93 (960) 4 54,9 (400) 80 (590) 93 (960) 4 57,9 8 (40) 89 (60) 93 (960) 3 6,0 (00) 34 (440) 98 (650) 93 (960) 3 64,0 (0) 40 (460) 07 (680) 93 (960) 3 67, (0) 46 (480) 6 93 (960) 3 70, (30) 5 (500) 6 (740) 93 (960) 3 73, (40) 58 (50) 35 (770) 93 (960) 3 76, (50) 65 (540) 44 (800) 93 (960) 79, (60) 7 (560) 53 (830) 93 (960) 8,3 77 (580) 85,3 (80) 83 (600) * Excludes No. 84 with Open Throat Top. NOTE: ine lengths given in table will allow hook to touch ground. When block travel below ground is required, add additional rope equal to parts of line times added travel distance. oisting distance or line pull may be limited when block travel below ground is required. Front and rear drums each provide 47 kn (33,000 lb) maximum single line pull. Auxiliary drum provides 89 kn (0,000 lb) maximum single line pull. 9 parts of line require upper boom point.
performance data Wire Rope engths uffing Jib No. 55 on No. 84 and uffing Jib ength 36,6 (0) 39,6 (30) (40) 45,7 (50) 5,8 54,9 57,9 6,0 (00) 64,0 (0) 67, (0) 70, (30) 73, (40) 76, (50) 79, (60) 8,3 85,3 (80) 88,4 (90) 9,4 (300) 94,5 (30) 97,5 (30) (3 Parts of ine) m 68 83 9 06 3 36 44 59 74 (ft) (550) (600) (65) (675) (700) (75) (775) (800) (850) (900) uffing Jib oist ine Front Drum ( Parts of ine) 30 (45) 37 (450) 45 (475) 60 (55) 68 (550) 75 (575) 83 (600) 9 (65) 98 (650) 06 (675) 3 (700) 9 (750) 36 (775) 44 (800) 5 (85) 59 (850) 67 (875) 8 (95) 90 (950) ( Parts of ine) 8 88 (90) 95 (30) 0 (330) 07 (350) 3 (370) 9 (390) 5 (40) 3 (430) 37 (450) 43 (470) 49 (490) 55 (50) 6 (530) 68 (550) 74 (570) 80 (590) 86 9 (630) 98 (650) 04 (670) 00,6 (330) 0 (690) Note: oist line lengths given in table will allow hook to touch ground. When block travel below ground is required, add additional rope equal to parts of line times added travel distance. oisting distance or line pull may be limited when block travel below ground is required. Wire Rope engths uffing Jib No. 55 on No. 84 and uffing Jib ength 36,6 (0) 39,6 (30) (40) 45,7 (50) 5,8 54,9 57,9 6,0 (00) 64,0 (0) 67, (0) 70, (30) 73, (40) 76, (50) 79, (60) 8,3 85,3 (80) 88,4 (90) 9,4 (300) 94,5 (30) 97,5 (30) (3 Parts of ine) 68 (550) 83 (600) 9 (65) 06 (675) 3 (700) (75) 36 (775) 44 (800) 59 (850) 74 (900) 8 (95) 97 (975) 305 (000) 30 (050) 335 (00) 343 (5) 358 (75) uffing Jib oist ine Auxiliary Drum ( Parts of ine) 30 (45) 37 (450) 45 (475) 60 (55) 68 (550) 75 (575) 83 (600) 9 (65) 98 (650) 06 (675) 3 (700) 9 (750) 36 (775) 44 (800) 5 (85) 59 (850) 67 (875) 8 (95) 90 (950) 97 (975) 305 (000) ( Part of ine) 9 98 04 0 6 8 34 40 46 5 58 58 58 58 58 (300) (30) (340) (360) (380) (400) (40) (440) (460) (480) (500) (50) (50) (50) (50) (50) 00,6 (330) 3 (05) Note: oist line lengths given in table will allow hook to touch ground. When block travel below ground is required, add additional rope equal to parts of line times added travel distance. oisting distance or line pull may be limited when block travel below ground is required. 5
6 performance data Wire Rope engths Fixed Jib No. 38A on uffing Jib No. 55 on No. 84, uffing Jib and Fixed Jib ength 88,4 (90) 9,4 (300) 94,5 (30) 97,5 (30) 00,6 (330) 03,6 (340) 06,7 (350) 09,7 (360),8 (370) 5,8 (380) Fixed Jib Whip ine Front Drum or Auxiliary Drum ( Part of ine) 86 9 (630) 98 (650) 04 (670) 0 (690) 6 3 (730) 9 (750) 35 (770) 4 (790) 8,9 (390) 47 Note: ine lengths are based on single part lead line. oist line and whip line lengths given in table will allow hook to touch ground. When block travel below ground is required, add additional rope equal to parts of line times added travel distance. oisting distance or line pull may be limited when block travel below ground is required. Maximum load on 6 mm or (") wire rope is 400 kg (7,500 lb) per line. When auxiliary drum is used maximum load is 9 070 kg (0,000 lb). Drum Capacities - Wire Rope Front or Rear Grooved Drum 8 mm Wire Rope* Auxiliary Drum 8 mm Wire Rope* Maximum ength 93 m (96 ft) 6 ayers 93 m (96 ft) 6 ayers Wire Rope Specifications 5: Safety Factor No. 84 - or - Fixed Jib No. 34 on No. 84 Function Part Number Size Wire Rope Minimum Breaking Strength Maximum oad Per ine Approximate Weight Function Part Number Size Wire Rope Minimum Breaking Strength Maximum oad Per ine Approximate Weight 5: Safety Factor Rotation Resistant, Right and ang ay Wire rope with Pad Eye oist ine No. A00840 8 mm 750,8 kn (68,800 lb) 4 970 kg (33,000 lb) 3,9 kg/m (.63 lb/ft) Whip ine No. A00840 8 mm 750,8 kn (68,800 lb) 3 608 kg (30,000 lb) 3,9 kg/m (.63 lb/ft) Wire Rope Specifications 3.5: Safety Factor No. 84 - or - Fixed Jib No. 34 on No. 84 Auxilliary ine No. A00840 8 mm 750,8 kn (68,800 lb) 3 608 kg (30,000 lb) 3,9 kg/m (.63 lb/ft) 3.5: Safety Factor 6 x 36 Extra Extra Improved Plow Steel, Right and Regular ay, IWRC Wire rope with Pad Eye oist ine No. A0479 Whip ine No. A0479 Auxilliary ine No. A0479 8 mm 603, kn (35,600 lb) 4 970 kg (33,000 lb) 3,33 kg/m (.4 lb/ft) 8 mm 603, kn (35,600 lb) 3 608 kg (30,000 lb) 3,33 kg/m (.4 lb/ft) 8 mm 603, kn (35,600 lb) 3 608 kg (30,000 lb) 3,33 kg/m (.4 lb/ft) Auxiliary Drum (8 mm) Wire Rope* oist Drum mm (7/8") Wire Rope 93 m (96 ft) 6 ayers m (75 ft) 8 ayers *5 m (8') is deducted from maximum spooling capacities for 3 dead wraps per drum or lagging. Maximum ength Unassisted Raising Method Over end of blocked crawlers m (ft) No. 38A Fixed Jib on No. 55 uffing Jib on No. 84 Main Main 36,6 (0) (40) 5,8 Jack-Knife Procedure uffing Jib - (40-60) - (40-60) - (40-60) - (40-60) Fixed Jib 9, - 8,3 (30-60) 9, - 8,3 (30-60) 9, - 8,3 (30-60) 9, - 8,3 (30-60) NOTE: oad block(s), hook(s) and weight ball(s) on ground at start. Maximum ength Unassisted Raising Over end of blocked crawlers m (ft) No. 84 with eavy-ift Top - or - No. 34 Fixed Jib on No. 84 with eavy-ift Top Series Main 76, (50) 73, (40) 70, (30) 67, (0) 64,0 (0) 6,0 (00) Fixed Jib, (40) 8,3 4,4 NOTE: oad block(s), hook(s) and weight ball(s) on ground at start. Upper boom point cannot be used when jib is attached. Upper boom point cannot be used on 76,. m (50') boom.
performance data Maximum ength Unassisted Raising Method No. 55 uffing Jib on No. 84 Main Jack-Knife Procedure Without Intermediate Fall Main uffing Jib Maximum ength Unassisted Raising Method No. 55 uffing Jib on No. 84 Main Main Jack-Knife Procedure With Intermediate Fall uffing Jib 7 30,5 (00) 7,4 45,7 - (50-60) 33,5 (0) 45,7 - (50-60) 30,5 (00) - (40-60) Over end of blocked crawlers m (ft) 36,6 (0) 39,6 (30) (40) - (40-60) 36,6 - (0-60) 30,5 - (00-60) Over end of blocked crawlers m (ft) 33,5 (0) 36,6 (0) 39,6 (30) 39,6 - (30-60) 36,6 - (0-60) 33,5 - (0-60) 45,7 (50) 4,4 - (80-60) (40) 33,5 - (0-60) 8,3 - (60-60) 45,7 (50) 33,5 - (0-60) 5,8 8,3 - (60-60) NOTE: oad block(s), hook(s) and weight ball(s) on ground until boom and luffing jib are erected. 5,8 33,5 - (0-60) 33,5-45,7 (0-50) NOTE: oad block(s), hook(s) and weight ball(s) on ground until boom and luffing jib are erected. Maximum ength Unassisted Raising No. 55 uffing Jib on No. 84 Main Maximum ength Unassisted Raising No. 55 uffing Jib on No. 84 Main Method Main In-ine Procedure Without Intermediate Fall uffing Jib Method Main In-ine Procedure With Intermediate Fall uffing Jib 8,3 8,3 - (60-60) 8,3 33,5 - (0-60),3 8,3 - (60-60),3 33,5 - (0-60) Over end of blocked crawlers m (ft) 4,4 7,4 30,5 (00) 8,3 - (60-60) 8,3 - (60-60) 8,3-45,7 (60-50) Over end of blocked crawlers m (ft) 4,4 7,4 30,5 (00) 33,5 - (0-60) 33,5 - (0-40) 33,5-39,6 (0-30) 33,5 (0) 36,6 (0) 39,6 (30) (40) 45,7 (50) 8,3 - (60-40) 8,3-39,6 (60-30) 8,3-33,5 (60-0) 8,3-7,4 (60-90) 8,3 -,3 (60-70) NOTE: oad block(s), hook(s) and weight ball(s) on ground until boom and luffing jib are erected. 33,5 (0) 36,6 (0) 33,5-36,6 (0-0) 33,5 (0) NOTE: oad block(s), hook(s) and weight ball(s) on ground until boom and luffing jib are erected.
performance data 8 Wire Rope Specifications 5: Safety Factor No. 84 - or - uffing Jib No. 55 on No. 84 5: Safety Factor Rotation Resistant, Right and ang ay Wire rope with Pad Eye Function Part Number oist ine No. A00840 Whip ine No. A00840 Auxilliary ine No. A00840 Size Wire Rope 8 mm 8 mm 8 mm Minimum Breaking Strength 750,8 kn (68,800 lb) 750,8 kn (68,800 lb) 750,8 kn (68,800 lb) Maximum oad Per ine 4 970 kg (33,000 lb) 3 608 kg (30,000 lb) 3 608 kg (30,000 lb) Approximate Weight 3,9 kg/m (.63 lb/ft) 3,9 kg/m (.63 lb/ft) 3,9 kg/m (.63 lb/ft) Wire Rope Specifications 3.5: Safety Factor No. 84 - or - uffing Jib No. 55 on No. 84 Function Part Number 3.5: Safety Factor 6 x 36 Extra Extra Improved Plow Steel, Right and Regular ay, IWRC Wire rope with Pad Eye oist ine No. A0479 Whip ine No. A0479 Auxilliary ine No. A0479 Size Wire Rope 8 mm 8 mm 8 mm Minimum Breaking Strength 603, kn (35,600 lb) 603, kn (35,600 lb) 603, kn (35,600 lb) Maximum oad Per ine 4 970 kg (33,000 lb) 3 608 kg (30,000 lb) 3 608 kg (30,000 lb) Approximate Weight 3,33 kg/m (.4 lb/ft) 3,33 kg/m (.4 lb/ft) 3,33 kg/m (.4 lb/ft) Working Weight Configuration 5, m (50') No. 84 kg (lb) Series Series 07 96 (38,05) 40 96 (309,05) 64,0 m (00') No. 84 * combined with 4,4 m (80') No. 34 Fixed Jib 5 89 (55,496) 48 096 (36,496) Typical working weight includes optional self-assembly carbody jacks, hydraulic reservoir full, fuel half-full, drums with standard lengths of wire rope, upper boom point, 36 mt (50 t) hook block, and 3,6 mt (5 t) hook and weight ball. Note: Upper boom point not used with fixed jib. *64,0 m (00') No. 8 boom maximum allowed.
performance data Main & Whip Drums - 47 kn (33,000 lb) ayer ine Pull kg (lb) 0) (0) Full Power Drum - Continuous Duty Single ine Pull/Single ine Speed m/min (ft/min) 3 4 5 87 (86) 96 (34) 04 (34) 3 (370) (398) 6 30 (46) Auxiliary Drum - 89,0 kn (0,000 lb) ayer ine Pull kg (lb) 0) (0) Full Power Drum - Continuous Duty Single ine Pull/Single ine Speed m/min (ft/min) 4 6 6 (380) 46 (480) 68 (550) 9 68) (5,000) 84 (74) 9 (300) 99 (36) 07 (35) 5 (376) (40) 68) (5,000) 0 (360) 37 (450) 56 (50) 4 536) (0,000) 8 (63) 87 (86) 94 (309) 0 (33) 08 (354) 5 (376) 4 536) (0,000) 04 (340) 8 (40) 43 (470) 6 803) (5,000) 77 (5) 83 (73) 89 (93) 95 (33) 97 (38) 99 (33) 6 803) (5,000) 95 (30) 98 (30) 98 (30) 9 07) (0,000) 7 (36) 74 (4) 75 (47) 77 (5) 79 (58) 80 (63) 9 07) (0,000) 73 (40) 76 (50) 8 340) (5,000) 6 (00) 63 (05) 64 () 66 (6) 68 () 69 (7) NOTE: ine pull is infinitely variable. 3 380) (33,000) 5 (65) 5 54 (76) 55 (8) 57 (86) 59 (9) NOTE: ine pull is infinitely variable. Drums & aggings - iftcrane Application Drum ocation Drum Part Number Tandem Drums - 854 mm (73") Wide (Optional) Drum Type Drum Diameter Drum Width Drum or agging Groove Pitch * Minimum Wire Rope Size** oist Rear A00485 Grooved 540 mm 676 mm 9,39 mm 8,55 mm Basic iftcrane Regular Top -or- Basic ifcrane Open Throat Top Whip Auxiliary Front Butt A00485 A00485 Grooved Grooved (-/4") 540 mm (-/4") 540 mm (6-5/8") 676 mm (6-5/8") 676 mm (.57") 9,39 mm (.57") 9,39 mm (.4") 8,55 mm (.4") 8,55 mm (-/4") (6-5/8") (.57") (.4") Clalmshell imited Duty Closing olding Front Rear A00485 A00485 Grooved Grooved 540 mm (-/4") 540 mm (-/4") 676 mm (6-5/8") 676 mm (6-5/8") 9,39 mm (.57") 9,39 mm (.57") 8,55 mm (.4") 8,55 mm (.4") * Maximum wire rope dimeter and width a wond on drum must not exceed drum groove pitch. ** Minimum recommended wire rope size for proper spooling.
boom combinations 0 No. 84 Combinations ength 5, (50) 8,3,3 4,4 7,4 30,5 (00) 33,5 (0) Inserts 6, m (0 ft) 3,0 m (0 ft), m (40 ft) No. 34 Fixed Jib Combinations Jib ength 9, (30), (40) 5, (50) 8,3,3 4,4 Fixed Jib Inserts 3,0 m (0 ft) 6, m (0 ft) 36,6 (0) 39,6 (30) (40) 45,7 (50) 5,8 3 4,6 m (5 ft) No. 34 Jib Top 54,9 57,9 6,0 (00) 64,0 (0) 67, (0) 70, (30) 73, (40) 76, (50) 3 3 3 4 4 4 4 4 8,5 m (8 ft) No. 84 Top, m (40 ft) No. 34 Fixed Jib 4,4 m (80 ft) 6, m (0 ft) No. 34 Jib Inserts 3,0 m (0 ft) No. 34 Jib Insert 4,6 m (5 ft) No. 34 Jib Butt 8,5 m (8 ft) No. 84 Top Note: Uppermost, m (40') insert must include backstay lugs., m (40 ft), m (40 ft), m (40 ft), m (40 ft) No. 84 eavy-ift 76, m (50 ft) 6,7 m ( ft) No. 84 Butt Model 555 No. 84 eavy-ift Main 76, m (50 ft), m (40 ft) 6, m (0 ft) 3,0 m (0 ft) 3,0 m (0 ft) No. 84 eavy-ift 6,0 m (00 ft) Model 555 No. 34 Fixed Jib on No. 84 eavy-ift Main 85,3 m (80 ft), m (40 ft) 6, m (0 ft) 3,0 m (0 ft) 6,7 m ( ft)
boom combinations No. 84 OTT Combinations ength 8,3,3 4,4 7,4 30,5 (00) 33,5 (0) 36,6 (0) 39,6 (30) (40) 45,7 (50) 5,8 54,9 57,9 6,0 (00) 64,0 (0) 67, (0) 70, (30) 73, (40) Inserts 6, m (0 ft) 3,0 m (0 ft) 76, (50) 4 Note: Uppermost, m (40') insert must include backstay lugs., m (40 ft) 3 3 3 3 4 4 4 8,5 m (8 ft) No. 84 OTT Top, m (40 ft) No. 34 Fixed Jib Combinations Jib ength 9, (30), (40) 5, (50) 8,3,3 4,4 Fixed Jib Inserts 3,0 m (0 ft) 6, m (0 ft) No. 34 Fixed Jib 4,4 m (80 ft) 4,6 m (5 ft) No. 34 Jib Top 3,0 m (0 ft) No. 34 Jib Insert 4,6 m (5 ft) No. 34 Jib Butt 6, m (0 ft) No. 34 Jib Inserts,6 m (38 ft) No. 84 OTT Top, m (40 ft), m (40 ft), m (40 ft), m (40 ft), m (40 ft) No. 84 OTT 76, m (50 ft) No. 84 OTT 6,0 m (00 ft) 6, m (0 ft) Model 555 No. 84 OTT Main 76, m (50 ft) 3,0 m (0 ft) 6,7 m ( ft) No. 84 Butt Model 555 No. 34 Fixed Jib on No. 84 OTT Main 85,3 m (80 ft), m (40 ft) 6, m (0 ft) 6,7 m ( ft)
boom combinations No. 55 uffing Jib Combinations Jib ength 8,3,3 4,4 uffing Jib Inserts 3,0 m 6, m, m (0 ft) (0 ft) (40 ft) No. 38A Fixed Jib Combinations Jib ength 9, (30), (40) 5, (50) Fixed Jib Inserts 3,0 m (0 ft) No. 38A Fixed Jib 8,3 m (60 ft) 4,6 m (5 ft) No. 38A Jib Top 3,0 m (0 ft) No. 38A Jib Insert 7,4 30,5 (00) 33,5 (0) 8,3 3 4,6 m (5 ft) No. 38A Jib Butt 36,6 (0) 39,6 (30) 7,0 m (3 ft) No. 555 Jib Top 7,0 m (3 ft) No. 55 Jib Top (40) 45,7 (50), m (40 ft) No. 555 Jib Insert, m (40 ft) No. 55 Jib Insert Note: Intermediate fall insert can be used only on boom combinations of 33,5 m (0') up to m (60'). Maximum luffing jib length with intermediate fall on maximum boom length is 97,5 m (30'). 6, m (0 ft) No. 555 Jib Insert 3,0 m (0 ft) No. 555 Jib Insert, m (40 ft) No. 555 Jib Insert No. 55 uffing Jib with Intermediate Fall m (60 ft), m (40 ft) No. 555 Jib Insert with Intermediate Fall No. 55 uffing Jib m (60 ft) 6, m (0 ft) No. 555 Jib Insert 3,0 m (0 ft) No. 555 Jib Insert 8, m (7 ft) No. 555 Jib Butt 8, m (7 ft) No. 555 Jib Butt,4 m (8 ft) No. 84 Cap,4 m (8 ft) No. 84 Cap, m (40 ft), m (40 ft), m (40 ft), m (40 ft) No. 84 eavy-ift 5,8 m (70 ft), m (40 ft) 6, m (0 ft) 6,7 m ( ft) No. 84 eavy-ift 5,8 m (70 ft), m (40 ft) 6, m (0 ft) 6,7 m ( ft) Model 555 No. 55 uffing Jib with Intermediate Fall on No. 84 eavy-ift Main 00,6 m (330 ft) Model 555 No. 38A Fixed Jib on No. 55 uffing Jib on No. 84 eavy-ift Main 8,9 m (390 ft)
heavy-lift boom range diagram (60) 79, No. 84 Main 83 0 80 0 3 (50) 76, (40) 73, (30) 70, (0) 67, (0) 64,0 (00) 6,0 64,0 (0) 6,0 (00) 70, (30) 67, (0) 76, (50) 73, (40) 70 0 60 0 50 0 57,9 57,9 54,9 54,9 EIGT ABOVE GROUND 5,8 (50) 45,7 (40) (30) 39,6 (0) 36,6 (0) 33,5 39,6 (30) 36,6 (0) 33,5 (0) 45,7 (50) (40) 5,8 40 0 30 0 (00) 30,5 30,5 (00) 7,4 7,4 4,4,3 8,3 (50) 5, 8,3 5, (50) 4,4,3 0 0 (40), (30) 9, 5,50 m (8' ") TAISWING,5 m (5' 0") ROTATION,85 m (6' "), (40) 8,3 4,4 30,5 (00) 36,6 (0) (40) DISTANCE FROM CENTERINE OF ROTATION 54,9 6,0 (00)
heavy-lift load charts 4 iftcrane Capacities - Series No. 84 44 678 kg (98,500 lb) Upperworks Counterweight 9 958 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 5, (50.0) 8,3,3 7,4 33,5 (0) 39,6 (30) 45,7 (50) 5,8 57,9 64,0 (0) 70, (30) 76, (50) 4,6 (5) (300.0) 35,6 (99.0) 5,0 (7) 5,0 (66.5) 5,0 (66.4) 3,7 (66.) 6,0 (0) 04,9 (8.0) 04,9 (7.9) 0 (7.7) 00,3 (0.4) 7,0 (4) 88,3 (79.9) 88,7 (80.6) 88,6 (80.9) 88,9 (8.) 84,0 (8.3) (59.3) Fixed Jib No. 34 on eavy-ift No. 84 Jib ength Deduct from Capacity when fixed jib is attached kg (lb) 8,0 (8) 9,0 (3),0 (36) 70,9 (4.9) 59,4 (6.6) 44,5 (98.5) 7, (4.5) 59,7 (7.) 44,7 (99.0) 7,3 (4.8) 59,8 (7.4) 4 (99.) 7,4 (4.9) 59,8 (7.4) 4 (99.3) 7,5 (43.0) 59,9 (7.5) 4 (99.3) 69,6 (4.8) 60,0 (7.3) 44,7 (99.0) 6,9 (33.6) 58,9 (6.9) 44,6 (98.7) (5.7) 5,5 (0.3) 44,4 (98.3) (94.8) 40,8 (90.) (79.5) 9, (30), (40) 5, (50) 8,3,3 4,4 70 (3,900) 30 (4,700) 540 (5,600) 990 (6,600) 3 450 (7,600) 3 950 (8,700),0 (40) 5,0 (50) 8,0 0,0 39,3 (84.9) 8,7 (6.0) 39,6 (85.4) 9,0 (6.7),4 (48.5) 39,7 (85.6) 9, (6.9),6 (48.9) 9,5 (39.) 39,7 (85.7) 9, (63.0),7 (49.0) 9,6 (39.5) 39,6 (85.6) 9, (6.9),6 (48.9) 9,6 (39.4) 39,5 (85.3) 9,0 (6.6),5 (48.6) 9,4 (39.0) 39,4 (85.0) 8,8 (6.),3 (48.) 9, (38.7) 39, (84.6) 8,6 (6.7), (47.7) 9,0 (38.) 38,7 (84.) 8,4 (6.3),8 (47.) 8,7 (37.7) 34,5 (75.6) 8,4 (60.7),6 (46.6) 8,5 (37.) 30,3 (66.3) 6,6 (58.),4 (46.) 8, (36.5) (54.3),9 (47.9) 9,0 (4.4) 7, (35.4) Deduct 590 kg (,300 lb) from capacities when upper boom point is attached. 4,0 6,0 5,0 (3.5) 3,3 (7.) 5,0 (3.5) 3,4 (7.3) 4,9 (3.) 3, (7.0) 4,7 (3.8) 3,0 (6.6) 4,4 (3.),8 (6.0) 4,3 (30.8),6 (5.5) 4,0 (30.),3 (4.9) 3,7 (9.6),0 (4.3) 3,4 (8.9),8 (3.7) 30,0 (00) 0,7 (3.) 0,6 (.9) 0,4 (.5) 0, (.9) 0,0 (.5) 9,7 (0.8) 9,4 (0.) 9, (9.6) 3,0 (0) 9,7 (9.8) 9,5 (9.5) 9,4 (9.) 9, (8.7) 8,9 (8.) 8,6 (7.5) 8,3 (6.9) 8, (6.3) (0) 7,8 (6.8) 7,7 (6.5) 7,4 (5.9) 7, (5.5) 6,9 (4.8) 6,6 (4.) 6,3 (3.6) 38,0 (30) 7, (4.4) 6,9 (4.) 6,7 (3.7) 6,5 (3.) 6, (.6) 5,9 (.0) 5,6 (.3) 4,0 (40) 5,7 (.) 5,5 (.7) 5, (.) 5,0 (0.6) 4,7 (0.0) 4,4 (9.4) 44,0 (50) 5, (0.5) 4,9 (0.0) 4,7 (9.6) 4,4 (9.0) 4, (8.4) 3,9 (7.7) 4,0 (8.6) 3,8 (8.) 3,5 (7.5) 3, (6.9) 3,0 (6.3) 50,0 54,0 56,0 (85) 3,6 3,4 (6.8),7 (5.7),3 (5.) 3, (6.),4 (5.), (4.6),9 (5.7), (4.5),8 (4.0),6 (5.0) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
heavy-lift boom range diagram No. 84 OTT 5
heavy-lift load charts 6 iftcrane Capacities - Series No. 84 OTT 44 678 kg (98,500 lb) Upperworks Counterweight 9 958 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 8,3 (60.0),3 4,4 30,5 (00) 36,6 (0) (40) 45,7 (50) 5,8 57,9 64,0 (0) 70, (30) 76, (50) 4,3 (4) (300.0) 5,0 (7) 4,9 (66.3) 3,6 (66.) (48.9) 6,0 (0) 05,0 (8.0) 04,9 (7.8) 05, (7.5) 9 (08.0) 7,0 (4) 88,5 (80.4) 88,6 (80.7) 88,6 (80.8) 87,5 (80.8) 8, (76.) Fixed Jib No. 34 on No. 84 OTT Jib ength Deduct from Capacity when fixed jib is attached kg (lb) 9,0 (30) 0,0 (34),0 (40) 59,7 (8.8) 5,3 (07.6) 39,7 (85.8) 59,8 (9.0) 5,4 (07.8) 39,8 (86.0) 59,9 (9.) 5,4 (07.9) 39,8 (86.0) 59,8 (8.9) 5,3 (07.7) 39,7 (85.8) 59,7 (8.8) 5,3 (07.5) 39,6 (85.6) 59,9 (8.4) 5, (07.) 39,4 (85.) 59,6 (8.3) 5,0 (07.0) 39,4 (85.0) (9.3) 5, (06.5) 39, (84.5) 44,7 (98.4) 39,0 (84.) 37, (8.) 35, (77.5) (63.) 9, (30), (40) 5, (50) 8,3,3 4,4 70 (3,900) 30 (4,700) 540 (5,600) 990 (6,600) 3 450 (7,600) 3 950 (8,700) 5,0 (50) 8,0 0,0 4,0 9, (63.),8 (49.) 9,3 (63.4),9 (49.5) 9,8 (39.9) 9,3 (63.4),9 (49.5) 9,8 (40.0) 5,3 (33.) 9, (63.),8 (49.3) 9,7 (39.8) 5,3 (33.0) 9, (63.0),7 (49.) 9,6 (39.6) 5, (3.8) 8,9 (6.5),5 (48.6) 9,4 (39.) 4,9 (3.3) 8,9 (6.4),4 (48.4) 9,3 (39.0) 4,9 (3.) 8,6 (6.8), (47.9) 9, (38.4) 4,6 (3.6) 8,4 (6.3),9 (47.4) 8,8 (37.9) 4,4 (3.) 8, (60.8),7 (46.8) 8,6 (37.3) 4, (30.4) 8,0 (60.),3 (46.) 8,3 (36.6) 3,8 (9.8) 7, (59.6), (45.5) 8,0 (36.0) 3,5 (9.) Deduct 590 kg (,300 lb) from capacities when upper boom point is attached. 6,0 30,0 (00) 3,6 (7.8) 0,9 (3.6) 3,5 (7.6) 0,9 (3.5) 3,3 (7.) 0,7 (3.0) 3, (7.0) 0,6 (.9),9 (6.4) 0,4 (.4),7 (5.9) 0, (.8),4 (5.) 9,8 (.), (4.6) 9,5 (0.5),9 (4.0) 9, (9.9) 3,0 (0) 9,8 (0.) 9,6 (9.8) 9,6 (9.7) 9,3 (9.) 9, (8.6) 8,8 (7.9) 8,5 (7.3) 8, (6.6) (0) 8, (7.5) 7,9 (7.) 7,9 (7.0) 7,6 (6.4) 7,4 (5.9) 7, (5.) 6,8 (4.6) 6,5 (3.9) 38,0 (30) 7, (4.8) 7, (4.7) 6,9 (4.) 6,7 (3.6) 6,4 (3.0) 6, (.3) 5,8 (.7) 4,0 (40) 6,0 (.8) 5,9 (.8) 5,7 (.) 5,4 (.7) 5, (.) 4,9 (0.4) 4,6 (9.8) 44,0 (50) 5,4 5, (0.6) 4,9 (0.) 4,6 (9.4) 4,3 (8.8) 4,0 (8.) 4, (9.) 4,0 (8.6) 3,7 (8.0) 3,5 (7.4) 3, (6.7) 50,0 3,8 3,6 (7.3) 3,3 (6.7) 3,0 (6.),7 (5.4) 54,0 56,0 (85) 58,0 (95),9 (6.),6 (5.7),6 (5.6),3 (5.),0 (4.),3 (5.0),0 (4.5), (4.3) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib range diagram (90) 88,4 (80) 85,3 8,3 No. 34 Fixed Jib on No. 84 Main 80 0 70 0 7 (60) 79, (50) 76, (40) 73, 8,3,3 4,4 79, (60) 8,3 85,3 (80) 60 0 (30) 70, (0) 67, (0) 64,0 (00) 6,0 57,9 54,9 9, (30), (40) 5, (50) 57,9 6,0 (00) 64,0 (0) 67, (0) 70, (30) 73, (40) 76, (50) 50 0 40 0 EIGT ABOVE GROUND 5,8 (50) 45,7 (40) (30) 39,6 (0) 36,6 (0) 33,5 36,6 (0) 39,6 (30) (40) 45,7 (50) 5,8 54,9 30 0 (00) 30,5 7,4 4,4,3 8,3 (50) 5, (40), (30) 9, 5,50 m (8' ") TAISWING,5 m (5' 0") ROTATION,85 m (6' "), (40) 8,3 4,4 30,5 (00) 36,6 (0) (40) DISTANCE FROM CENTERINE OF ROTATION 54,9 6,0 (00) 67, (0)
fixed jib load charts 8 iftcrane Capacities - Series Fixed Jib No. 34 with 3 80 mm (' 6") strut on No. 84 44 678 kg (98,500 lb) Upperworks Counterweight 9 958 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 5 Offset 5 Offset 7,4 36,6 (0) 57,9 67, (0) 7,4 36,6 (0) 57,9 67, (0) Jib 9, m (30 ft) 9, (30),0 (40) 4,0 (50) 8,0 4,0 8,0 (00) (0) 40,0 (40) 6,7 (59.0) 6,7 (59.0) 6,7 (58.7) 3, (49.5) 5,3 (33.), (3.7) 6,7 (59.0) 6,7 (59.0),7 (48.8) 5,0 (3.4),9 (3.0) 7,9 (7.0) 6,5 (.7) (59.0) 6,7 (59.0), (47.6) 4,4 (3.),3 (.8) 7,3 (5.8) 6,0 (.6) 6,7 (59.0),7 (46.7) 4,0 (30.) 0,9 (0.8) 6,9 (4.8) 5,5 (0.6) (46.3) 0,5 (45.3) 3,6 (9.3) 0,4 (9.9) 6,4 (3.8) 5, (9.6) Jib 9, m (30 ft) (40) 4,0 (50) 8,0 0,0 4,0 8,0 (00) (0) 40,0 (40) (46.7) 9,7 (4.8) 7,3 (38.0) 6,4 (35.0) 4,9 (3.6),5 (4.),0 (44.8) 8,8 (4.) 7,9 (38.3) 5,6 (33.5),3 (3.8) 8, (7.4) (47.7) 0, (44.4) 9,3 (39.7) 5,0 (3.5),8 (.8) 7,6 (6.5) 6, (.),0 (46.) 9,5 (39.0) 4,7 (3.8),5 (.0) 7,3 (5.7) 5,9 (.) (40.9) 8,3 (38.3) 4,4 (3.0), (.) 6,9 (4.8) 5,5 (0.4) 3,9 (8.4) 3,5 (7.5) 3, (6.5) 3,7 (7.9) 3,3 (7.) 5,0 3, (6.0),7 (5.0),3 (4.) 5,0,5 (4.6) 60,0 (00) 56,0,8 7,4 36,6 (0) 57,9 64,0 (0) 7,4 36,6 (0) 57,9 64,0 (0) 9, (30) (40),0 (40) 8,5 (40.7) (4.0) 4,0 (50) 4,0 (50) 7,8 (38.5) 8,5 (40.0) 9, (4.5) (4.4) 8,0,8 (8.) 3, (9.0) Jib 5, m (50 ft) 8,0 4,0 8,0 (00) (0) 40,0 (40) 5,0 60,0 (00) 6,6 (36.6) 5, (33.3),6 (4.6) 8,6 (8.5) 7, 7,4 (38.) 5,4 (33.), (3.7) 8, (7.7) 6,8 (3.4) 4,7 (0.) 8, (39.9) 4,7 (3.8),6 (.4) 7,6 (6.3) 6, (.) 4, (8.9) 3,4 (6.5), (4.5) 8,6 (40.9) 4,3 (30.9), (.4) 7, (5.3) 5,7 (.) 3,7 (7.9),9 (5.5) 8,7 (4.3) 4,0 (30.) 0,9 (0.7) 6,8 (4.6) 5,4 (0.4) 3,4 (7.),6 (4.8) Jib 5, m (50 ft) 0,0 4,0 8,0 (00) (0) 40,0 (40) 5,0 56,0, (5.8) 0,9 (3.9) 9,9 (0.9),8 (7.6),7 (5.7) 0,8 (.8) 8,6 (8.6) 7, (4.0) 3, (8.8),6 (7.6),7 (4.) 8, (7.7) 6,7 (3.) 4,5 (9.7) (8.9),7 (7.9),0 (3.5) 7,8 (6.9) 6,4 (.3) 4, (8.9) 3,3 (6.),6 (5.) (7.9), (7.0),7 (.9) 7,6 (6.4) 6, (.7) 3,9 (8.3) 3,0 (5.6),3 (4.5) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib load charts Jib 8,3 m (60 ft) iftcrane Capacities - Series Fixed Jib No. 34 with 3 80 mm (' 6") strut on No. 84 44 678 kg (98,500 lb) Upperworks Counterweight 9 958 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 0,7 (35) 4,0 (50) 8,0 0,0 4,0 8,0 (00) (0) 40,0 (40) 7,4 3,6 (30.0) 3,5 (9.7),8 (8.),4 (6.8),6 (5.5) 0,9 (3.) 8,7 (8.8) 7,3 (4.5) 5 Offset 36,6 (0) 3,6 (30.0) 3,3 (9.4) 3,0 (8.),3 (7.0),6 (4.0) 8,3 (7.9) 6,9 (3.7) 4,9 (0.5) (30.0) 3,6 (30.0) 3,5 (9.5),9 (8.5),8 (.7) 7,7 (6.6) 6,3 (.3) 4,3 (9.) 57,9 3,6 (30.0) 3,6 (30.0) 3,3 (9.3),3 (.7) 7, (5.6) 5,9 (.3) 3,8 (8.) 64,0 (0) 3,6 (30.0) 3,6 (30.0) 3,5 (9.8),0 (.0) 6,9 (4.9) 5,5 (0.6) 3,5 (7.4) Jib 8,3 m (60 ft) 8,0 0,0 4,0 6,0 8,0 (00) (0) 40,0 (40) 5,0 7,4 (3.9) 0,5 (.9) 9,6 (.0) 9,0 (9.3) 8,6 (7.9) 7, (5.7) 36,6 (0) 0,8 (3.5) 0,3 (.7) 5 Offset 9,8 (.0) 9,3 (9.6) 7,9 (7.3) 7,3 (4.5) (4.) 0,6 (3.4) 0,4 (.8) 0, (.4) 8,4 (8.) 6,9 (3.5) 4,7 (0.0) 3,8 (7.3) 57,9 0,7 (3.5) 0,4 (.7) 0, (.0) 8, (7.3) 6,5 (.7) 4,3 (9.) 3,5 (6.5) 64,0 (0) 0,7 (.7) 0,4 (.0) 0, (.4) 8, (6.8) 6,5 (.) 4,3 (8.7) 3,5 (6.0) 9 56,0,8 (5.7),4 (4.7),0 (4.0) 56,0,7 (4.4),5 (4.8) 60,0 60,0, (4.4) 7,4 36,6 (0) 57,9 6,0 (00) 7,4 36,6 (0) 57,9 6,0 (00) 0,7 (35) 8,0 4,0 (50) 9, (0.) 9, (0.4) (0.6) 0,0 7,5 (6.4) (6.7) 8,0 9,0 (9.9) 9, (0.) 9, (0.4) 9,3 (0.5) 9,3 (0.6) 4,0 7, (5.6) 7,3 (6.) (6.5) Jib 4,4 m (80 ft) 0,0 4,0 8,0 (00) (0) 40,0 (40) 56,0 64,0 (0) 8,9 (9.) 8,3 (8.) 7,7 (6.4) 6,8 (4.9) 6,4 (3.6) 5,5 (.8) 9,0 (9.9) 8,8 (9.3) 8, (7.7) 7,3 (6.) 6,9 (4.0) 5,0 (0.8) 3,6 (7.4) 9, (0.) 9,0 (9.9) 8,8 (8.9) 7,8 (6.8) 6,4 (.5) 4,4 (9.4) 3,0 (6.0),9 (4.) 9, (0.3) 9, (0.) 9,0 (9.6) 7,3 (5.7) 5,9 (.5) 3,9 (8.3),5 (4.9) 9, (0.3) 9, (0.) 9,0 (9.8) 7, (5.4) 5,8 (.) 3,7 (8.0),3 (4.6) Jib 4,4 m (80 ft) 6,0 8,0 (00) (0) 40,0 (40) 5,0 60,0 (00) 64,0 (0) 6,9 (5.0) 6,7 (4.) 5,5 (.) 5, (0.7) 7, (5.5) 6,9 (4.9) 6, (3.4) 5,6 (.9) 4,9 (0.7) 4,6 7,3 (6.0) 7, (5.5) 6,6 (4.6) 6,3 (3.3) 5,0 (0.7) 4, (8.0),7 (5.8) 7,4 (6.3) 7,3 (5.9) 6,8 (5.0) 6,6 (3.4) 4,6 (9.9) 3,8 (7.),4 (5.0),8 (4.) 7,5 (6.4) 7,4 (6.0) 6,8 (5.) 6,6 (3.) 4,5 (9.6) 3,6 (6.9), (4.7) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
luffing jib range diagram 30 No. 55 uffing Jib on No. 84 Main
luffing jib load charts iftcrane uffing Jib Capacities - Series uffing Jib No. 55 on No. 84 44 680 kg (98,500 lb) Counterweight 9 960 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 88 Angle 3 uffing Jib ength 8,3 m (60 ft) 0,0 (35),0 (40) 4,0 (50) 6,0 (55) 8,0 0,0 4,0 6,0 8,0 (95) 8,3 (90.0) 38, (83.5) 3,7 (66.3) 8,4 (59.) 3,7 (50.6) 4,4 (90.0) 37,0 (80.5) 3,8 (64.7) 8,0 (59.) 5, (54.6) 30,5 (00) (88.) (( 87 35,9 (77.9) 30,9 (63.) 7,3 (58.0) 4,7 (53.8) (40) (( (69.0) (( (58.5) 8,0 (57.6) 5, (53.3),8 (49.7) 0,8 (36.5) 5,8 (50.6) (47.) (44.) (39.) uffing Jib ength 7,4 m (90 ft) 0,0 (35),0 (40) 4,0 (50) 6,0 (55) 8,0 0,0 4,0 6,0 8,0 (95) 8,3 (78.) 33,7 (73.9) 3,4 (66.4) 8,7 (59.3) 4,5 (53.),4 (43.5) 6,9 (36.7) 5, (7.9),6 (.0) 4,4 (77.0) 33,4 (73.) 3, (65.4) 8,4 (59.4) 5, (54.5), (45.) 7,6 (38.) 5,9 (3.5) 3,3 (5.) 30,5 (00) (75.0) 3,8 (7.) 30,7 (6.7) 7, (57.) 4, (5.8),0 (45.0) 7,5 (38.0) 5,8 (3.7) 4, (7.8) (40) (60.) 5,3 (53.0) 3, (49.7),4 (46.8) 9,8 (4.5) 7,0 (37.) 5,8 (3.6) 4,3 (30.4) 5,8 30,0 (00) 30,0 (00),7 (3.0) 8,3 4,4 30,5 (00) (40) 5,8 8,3 4,4 30,5 (00) (40) 5,8,0 (40) (56.) (55.3) (54.) (48.5),0 (40) uffing Jib ength 36,6 m (0 ft) 4,0 (50) 8,0 0,0 4,0 30,0 (00) (0) 4,0 (40) 3,9 (50.6) 0,9 (45.7) 9,5 (4.3) 7, (37.),7 (7.5) 8,4 (7.4) 3,6 (50.) 0,8 (45.6) 9,5 (4.4) 7, (37.5) 3,0 (8.) 9,6 (9.8) 3, (49.5) 0,7 (45.3) 9,5 (4.3) 7, (37.4),9 (8.0) 0, (.9),5 (46.9) 9,3 (4.) 8,0 (38.0) 5,7 (34.3),9 (7.9) 0, (.9) uffing Jib ength m (60 ft) 4,0 (50) 8,0 0,0 4,0 30,0 (00) (0) 4,0 (40) (3.7) 3,4 (9.3),4 (6.) 0,8 (3.5) 8,6 (8.8) 6,9 (5.) 5,5 (.0) 4,5 (9.7) (3.5) 3,3 (9.),4 (6.3) 0,8 (3.6) 8,7 (8.9) 7,0 (5.) 5,6 (.) 4,5 (9.8) (3.) 3,3 (9.),4 (6.) 0,8 (3.6) 8,8 (9.) 7,0 (5.3) 5,7 (.3) 4,6 (0.0) (7.),4 (7.3), (5.9) 0,7 (3.5) 8,8 (9.) 7, (5.6) 5,8 (.6) 4,7 (0.) (9.) 0,9 (4.0) 0,6 (3.3) 0, (.5) 8,8 (9.) 7, (5.7) 5,9 (.7) (0.3) (9.5) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
luffing jib load charts 3 iftcrane uffing Jib Capacities - Series uffing Jib No. 55 on No. 84 44 680 kg (98,500 lb) Counterweight 9 960 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 75 Angle uffing Jib ength 8,3 m (60 ft) 4,0 (50) 8,0 0,0 4,0 6,0 30,0 (00) 3,0 (0) (0) 38,0 (30) 8,3 (64.9) 3,8 (5.5) 0,8 (4.5) 6,5 (35.8) 4,4 3,3 (50.3) 0,3 (4.4) 6, (35.0) 30,5 (00) (( 87 (48.8) 9,7 (40.) 5,7 (34.0) 4, (9.) (40) (( (37.3) 4,5 (3.5) 3, (7.) 0,8 (3.5) 5,8 (9.3) (5.) (.9) uffing Jib ength 7,4 m (90 ft) 4,0 (50) 8,0 0,0 4,0 6,0 30,0 (00) 3,0 (0) (0) 38,0 (30) 8,3 0,5 (4.7) 6, (35.) 4,7 (30.3), (6.4), (3.) 4,4 (40.6) 5,8 (34.) 4,3 (9.4),8 (5.7) 0,8 (.6) 30,5 (00) 5,3 (33.) 3,8 (8.4),4 (4.8) 0,5 (.8) 8,9 (9.3) (40),7 (6.) 0,5 (.7) 9,6 (0.0) 8, (7.7) 7,6 (5.8) 5,8 40,0 (35) 40,0 (35) 8,3 4,4 30,5 (00) (40) 5,8 8,3 4,4 30,5 (00) (40) 5,8 (85) (3.8) (30.9) (85) uffing Jib ength 36,6 m (0 ft) 6,0 30,0 (00) 3,0 (0) (0) 38,0 (30) 4,0 (40) 54,0 58,0 4,3 (9.5),9 (5.7) 0,9 (.6) 9,3 (0.) 8,6 (7.9) 7,4 (6.0) 3,9 (8.6),5 (4.9) 0,5 (.9) 9,0 (9.4) 8,3 (7.3) 7, (5.5) (7.6),0 (3.9) 0, (.0) 8,6 (8.6) 8,0 (6.6) 6,9 (4.9) (.8) 9, (9.) 7,8 (6.9) 7, (5.0) 6, (3.4) 5,0 (0.8) uffing Jib ength m (60 ft) 6,0 30,0 (00) 3,0 (0) (0) 38,0 (30) 4,0 (40) 54,0 58,0 0,0 (.7) 9,3 (9.5) 8,0 (7.4) 7,5 (5.6) 6,5 (4.0) 5, (.) 4, (9.) 9,7 (0.5) 8,5 (8.4) 7,9 (6.4) 6,8 (4.6) 5,4 (.8) 4,4 (9.6) (0.0) 8, (7.6) 7,5 (5.6) 6,4 (3.9) 5, (.) 4, (9.) (8.) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
luffing jib load charts iftcrane uffing Jib Capacities - Series uffing Jib No. 55 on No. 84 44 680 kg (98,500 lb) Counterweight 9 960 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 65 Angle 33 uffing Jib ength 8,3 m (60 ft) 0,0 4,0 6,0 30,0 (00) 3,0 (0) (0) 38,0 (30) 4,0 (40) 44,0 (50) 8,3 (40.) 5,6 (33.9) 4, (9.0) 4,4 (3.3) 3,5 (7.8) 30,5 (00) (( 87,7 (6.) 0,6 (.9) 9,7 (40) (( 8,3 (7.) 7,0 (5.) 6,5 5,8 (.9) (.5) uffing Jib ength 7,4 m (90 ft) 0,0 4,0 6,0 30,0 (00) 3,0 (0) (0) 38,0 (30) 4,0 (40) 44,0 (50) 8,3 (8.3),4 (4.7) 0,4 (.7) 8,9 (9.) 4,4 0,8 (3.4) 9,9 (0.6) 8,4 (8.3) 7,8 30,5 (00) 9, (9.3) 7,9 (7.) 7,3 (5.) (40) (4.) 6, (.6) 5, (.3) (0.) 5,8 46,0 (55) 46,0 (55) 4,5 (9.4) 8,3 4,4 30,5 (00) (40) 5,8 8,3 4,4 30,5 (00) (40) 5,8 3,0 (05) 0, (.3) 3,0 (05) uffing Jib ength 36,6 m (0 ft) 34,0 (5) 38,0 (30) 4,0 (40) 44,0 (50) 50,0 54,0 60,0 (00) 6,0 (05) 9,3 (9.7) 7,9 (6.6) 6,8 (4.8) 6,4 (3.3) (8.5) 7,4 (5.5) 6,4 (3.9) 6,0 (.5) (4.3) 5,9 (.8) 5,5 (.5) (0.3) 4,4 uffing Jib ength m (60 ft) 34,0 (5) 38,0 (30) 4,0 (40) 44,0 (50) 50,0 54,0 60,0 (00) 6,0 (05) (5.6) 6,4 (3.9) 5,9 (.4) 5, (.) (0.0) 4, (9.0) (.8) 5,5 (.5) 4,7 (0.3) 4,4 (9.) 3,8 (8.3) 3, (6.6) (0.4) 4,3 (9.3) 4,0 (8.3) 3,4 (7.4),7 (5.9),5 (5.5) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib on luffing jib range diagram 34 No. 38A Fixed Jib on No. 55 uffing Jib on No. 84 Main
fixed jib on luffing jib load charts iftcrane Fixed Jib on uffing Capacities - Series Fixed Jib No. 38A at 3 Degree Angle on uffing Jib No. 55 on No. 84 44 680 kg (98,500 lb) Upperworks Counterweight 9 960 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 88 Angle 35 uffing Jib 45,7 (40) (50) 36.6 (0) (40) 36.6 (0) (40) 36.6 (0) (40) 6,8 (55),0 (6.5),3 (5.0) 0,0,7 (5.8),0 (4.) 0, (.3) 0,6 (3.) 9,9 (.8) 9, (0.) 9,5 (0.7) 8,9 (9.5) 8,3 (8.) Fixed Jib ength 9, m (30 ft) 4,0 30,0 (00) (0) 4,0 (40) 54,0 56,0, (4.3) 9,4 (0.6) 8, (7.9) 7, (5.8) 6,4 (4.0) 4,3 (7.9) 0,7 (3.7) 9,4 (0.6) 8, (7.9) 7, (5.4) 5,8 (.6) 4,6 (8.7) 9,8 (.7) 8,9 (9.4) 7,5 (6.5) 6,3 (3.7) 5, (.3) 4,3 (9.4) 0, (.5) 9, (0.) 8,0 (7.6) 7, (5.6) 6,4 (3.8) 5, (.) 4,4 (6.8) 9,6 (.3) 9, (0.) 8,0 (7.6) 6,9 (5.) 5,8 (.6) (0.5) 4,5 (7.5) 8,9 (9.7) 8,4 (8.4) 7, (5.8) 6, (3.4) 5, (.) 4,3 (9.4) 4, (8.) 9, (0.0) 8,6 (8.9) 7,9 (7.3) 7,0 (5.4) 6,3 (3.6) 5, (.) (9.6) 8,6 (8.9) 8, (7.9) 7,7 (6.8) 6,6 (4.5) 5,6 (.3) (0.4) 4,5 (9.6) 8,0 (7.7) 7,6 (6.7) 6,8 (5.0) 5,9 (.9) 5,0 (0.9) 4, (9.) 4,0 (8.5) 60,0 (00) 3, (5.6) 3,5 (6.3) 3,5 (6.9) uffing Jib 45,7 (40) (50) 36.6 (0) (40) 36.6 (0) (40) 36.6 (0) (40) (65) (4.6) (4.) (3.8) (4.0) Fixed Jib ength 8,3 m (60 ft) 4,0 30,0 (00) (0) 4,0 (40) 54,0 60,0 (00) 68,0 (0) 70,0 (30) 6, (3.8) 5,7 (.7) 5,3 (.8) (0.6) 4,3 (9.4) 3,8 (8.4) 3,5 (7.6) 6, (3.5) 5,6 (.4) 5, (.6) 4,9 (0.7) 4,3 (9.4) 3,8 (8.4) 3,5 (7.7) 5,9 (3.0) 5,5 (.) 5, (.3) (0.7) 4,3 (9.4) 3,8 (8.4) 3,3 (7.) 6,0 (3.) 5,5 (.) 5, (.4) (0.4) 4, (9.) 3,8 (8.3) 3,4 (7.5) (4.9) 5,8 (.9) 5,4 (.0) 5, (.) (0.5) 4, (9.3) 3,8 (8.3) 3,4 (7.5) (5.5) 5,6 (.5) 5, (.6) 4,9 (0.9) 4,7 (0.3) 4, (9.3) 3,8 (8.3) 3,3 (7.) (6.0) 5,7 (.6) 5,3 (.7) 5,0 (.0) 4,7 (0.3) 4, (9.) 3,7 (8.) 3,4 (7.4),8 (6.8) 5,5 (.) 5, (.4) (0.7) 4,6 (0.) 4, (9.) 3,7 (8.) 3,4 (7.4),9 (6.7), (4.5) 5,3 (.7) 5,0 (.0) 4,7 (0.4) 4,4 (9.8) 4, (9.) 3,7 (8.) 3, (7.0),6 (6.0),3 (5.0) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib on luffing jib load charts 36 iftcrane Fixed Jib on uffing Capacities - Series Fixed Jib No. 38A at 3 Degree Angle on uffing Jib No. 55 on No. 84 44 680 kg (98,500 lb) Upperworks Counterweight 9 960 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 85 Angle uffing Jib 45,7 (40) (50) 36.6 (0) (40) 36.6 (0) (40) 36.6 (0) (40) 0,0 (5.8) 4,0,5 (5.3) 0,7 (3.7) 9,9 (.9) 0, (.6) 9,6 (.3) (9.7) 9, (0.0) (8.9) (7.6) Fixed Jib ength 9, m (30 ft) 6,0 30,0 (00) (0) 4,0 (40) 54,0 60,0 (00), (3.7) 0,0 (.8) 8,6 (8.8) 7,5 (6.) 6, (3.) 5,0 (0.8) 0,6 (3.3) 0,0 (.9) 8,6 (8.9) 7,4 (6.0) 6,0 (3.0) 4,9 (0.7) 9,8 (.5) 9,6 (.) 8,7 (9.0) 7, (5.7) 5,9 (.8) (0.5) 0, (.0) 9,7 (.3) 8,4 (8.5) 7,4 (6.) 6,0 (3.) 5,0 (0.7) 9,5 (0.8) 9, (0.4) 8,5 (8.6) 7,3 (5.8) 5,9 (.9) 4,9 (0.5) 3,7 (5.8) 8,8 (9.4) 8,6 (8.9) 8, (8.) 7, (5.6) 5,8 (.6) (0.4) 3,8 (7.9) 8,9 (9.5) 8,6 (9.0) 8, (8.) 7,3 (5.8) 5,9 (.8) (0.4) 4,0 (8.6) 8,4 (8.5) 8, (8.0) 7,8 (7.3) 7, (5.5) 5,8 (.6) (0.3) 3,9 (8.4) 7,9 (7.3) 7,6 (6.9) 7,3 (6.) 7,0 (5.) 5,7 (.3) 4,7 (0.) 3,8 (8.) 64,0 (0), (4.7) 3,0 (6.7) uffing Jib 45,7 (40) (50) 36.6 (0) (40) 36.6 (0) (40) 36.6 (0) (40) 4,0 (4.0) Fixed Jib ength 8,3 m (60 ft) 6,0 30,0 (00) (0) 4,0 (40) 54,0 60,0 (00) 68,0 (0) 7,0 (40) 6, (3.4) 5,9 (.9) 5,4 (.0) 5, (.) 4,5 (9.8) 4,0 (8.7) 3,6 (7.9) 6,0 (3.) 5,7 (.7) 5,3 (.8) 5,0 (.) 4,5 (9.9) 4,0 (8.8) 3,6 (8.0) (5.0) 5,8 (.8) 5,6 (.4) 5, (.6) 4,9 (0.9) 4,6 (0.0) 4, (8.9) 3,6 (8.0) (6.8) 5,9 (.9) 5,6 (.4) 5, (.6) 4,9 (0.9) 4,4 (9.6) 3,9 (8.6) 3,5 (7.8),9 (7.) 5,8 (.6) 5,5 (.) 5, (.4) 4,9 (0.8) 4,4 (9.7) 3,9 (8.7) 3,5 (7.8) 3, (7.) (.) 5,3 (.8) 5,0 (.) (0.5) 4,5 (9.8) 4,0 (8.8) 3,6 (7.9) 3, (7.) 5,6 (.) 5,3 (.8) 5,0 (.) 4,7 (0.5) 4,3 (9.5) 3,9 (8.5) 3,5 (7.7) 3, (7.0) (.9) 5, (.5) 4,9 (0.9) 4,6 (0.3) 4,4 (9.6) 3,9 (8.5) 3,5 (7.7) 3, (7.) 3,0 (.5) 5,0 (.) (0.5) 4,5 (0.0) 4,3 (9.6) 3,9 (8.6) 3,5 (7.8) 3, (7.),7 (4.9) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib on luffing jib load charts iftcrane Fixed Jib on uffing Capacities - Series Fixed Jib No. 38A at 3 Degree Angle on uffing Jib No. 55 on No. 84 44 680 kg (98,500 lb) Upperworks Counterweight 9 960 kg (44,000 lb) Carbody Counterweight 360 Rating kg (lb) x 000 80 Angle 37 uffing Jib 45,7 (40) (50) 36.6 (0) (40) 36.6 (0) (40) 36.6 (0) (40) 8,0 (95) (3.7) 3,0 (05) 0, (.4) 9,8 (.7) 9, (0.3) 9,4 (0.8) 8,8 (9.6) 8, (8.) 8,3 (8.3) 7,8 (7.3) Fixed Jib ength 9, m (30 ft) (0) 4,0 (40) 54,0 60,0 (00) 64,0 (0) 68,0 (0) 8,5 (8.5) 6,8 (4.7) 5,5 (.9) 4,5 (9.7) 8, (7.9) 6,5 (4.) 5,3 (.4) 4,3 (9.3) 3,5 (7.6) 7,9 (7.) 6,3 (3.6) 5,0 (0.9) 4, (8.9) 3,3 (7.) 8,5 (8.4) 6,7 (4.6) 5,4 (.8) 4,4 (9.6) 3,6 (7.8) 8, (7.7) 6,5 (4.0) 5, (.3) 4,3 (9.) 3,5 (7.5) 3,0 (6.7) 7,9 (7.0) 6, (3.4) 5,0 (0.8) 4,0 (8.7) 3,3 (7.),9 (6.4) 8, (7.8) 6,6 (4.) 5,3 (.4) 4,3 (9.3) 3,5 (7.5) 3,0 (6.8) 7,7 (6.9) 6,3 (3.7) 5, (0.9) 4, (8.8) 3,3 (7.),9 (6.4) (5.7) 7, (5.9) 6, (3.) (0.4) 3,9 (8.4) 3, (6.8),7 (6.),3 (5.4) (5) (5.) uffing Jib 45,7 (40) (50) 36.6 (0) (40) 36.6 (0) (40) 36.6 (0) (40) (0) (.6) (.4) (.) Fixed Jib ength 8,3 m (60 ft) (0) 4,0 (40) 54,0 60,0 (00) 68,0 (0) 70,0 (30) 7,0 (40) 76,0 (50) 5,5 (.) 5, (.5) (0.5) 4, (9.3) 3,8 (8.4) 3,0 (6.9) 5,4 (.0) 5, (.4) 4,9 (0.7) 4,3 (9.5) 3,7 (8.0),9 (6.6),6 (5.9) 5,3 (.8) 5,0 (.) (0.6) 4, (9.) 3,5 (7.5),7 (6.),5 (5.6) 5,3 (.7) 5,0 (.) 4,7 (0.3) 4, (9.) 3,7 (8.) 3,0 (6.8),8 (6.) 5, (.5) 4,9 (0.9) 4,7 (0.4) 4,3 (9.4) 3,6 (7.8),8 (6.4),6 (5.8),4 (5.3) (.) (0.7) 4,6 (0.) 4, (9.0) 3,4 (7.4),6 (6.),5 (5.5),3 (4.9) 5,0 (.) (0.6) 4,6 (0.) 4, (9.0) 3,7 (7.9),8 (6.5),6 (5.9),5 (5.3) (0.8) 4,7 (0.4) 4,5 (9.9) 4, (9.) 3,4 (7.5),6 (6.),5 (5.5),3 (5.0),0 (4.4) (0.5) 4,6 (0.) 4,4 (9.7) 4,0 (8.6) 3, (7.0),5 (5.7),3 (5.), (4.6),8 (4.) Meets ANSI B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
Manitowoc Crane CARE 38 Crane CARE is Manitowoc s comprehensive service and support program. It includes classroom and on-site training, prompt parts availability, expert field service, technical support and documentation for every one of the more than 7,000 Manitowoc cranes currently in use throughout the world. That s commitment you won t find anywhere else. That s Crane CARE. Service Training Manitowoc specialists work with you in our training center and in the field to make sure you know how to get maximum performance, reliability and life from your cranes. Manitowoc Cranes Technical Training Center provides valuable multi-level training, which is available for all models and attachments, in the following format: Basic Provides technicians with the basic skills required in our evel I and II classes covering hydraulic and electrical theory and schematics, pump, motor, control, and MI operation, and the use of meters and gauges. evel This model-specific class covers theory and offers hands-on training and trouble shooting for all crane systems. evel This model-specific class provides in depth coverage of all crane systems and components, and advanced troubleshooting of simulated faults. (Requires evel.) evel 3/Master Covering all EPIC models and the 400W, this class stresses high level system knowledge and trouble shooting of simulated faults. (Requires evel.) Parts Availability Genuine Manitowoc replacement parts are accessible through your distributor 4 hours a day, 7 days a week, 365 days a year. Service Interval Kits Provides all the parts required by Manitowoc s Preventative Maintenance Checklist. ydraulic Filter Kit Consists of the following: Filter Element - ydraulic in Tank (4) Cummins Model QSZ5-C600 Diesel Service Interval Kits 00 our Kit Consists of the following: Engine Filter Oil () Filter Water () Filter Fuel (),000 our Kit Consists of the following: Engine Filter Air Cleaner - Primary () Filter Oil () Filter Water (4) Filter Fuel () ydraulic Filter Element - ydraulic in Tank (4) Element - ydraulic Tank Breather (),000 our Kit Consists of the following: Engine Filter, Air Cleaner - Primary () Filter, Air Cleaner - Safety () Filter, Oil () Filter, Water () Filter, Fuel () Ether, (Bottle) () Sensor, Coolant evel (0) Belt, Fan () Belt, Alternator (set of two) () Filter, Element () ydraulic Filter Element - No substitutions allowed Filter - ydraulic In-Tank Suction (4) Kit, Engine Coolant Additive (SCA) Test () Kit, Seal (for hydraulic in tank filter) () Seal, Radial (for air cleaner) () ydraulic Test Kit Protect your investment by demanding Genuine Manitowoc Parts Service Kits. The ydraulic Service Kit consist of the following: All hydraulic fittings to access all pressures and flows ydraulic flow meters and pressure gauges to record hydraulic data. Electrical Break out harnesses to access voltages on all electrical circuits on all machines. Fluke Digital volt ohm meter, as used in all Manitowoc service literature.
Manitowoc Crane CARE ydraulic Test Kit with case The above kit plus a custom heavy-duty carrying case. U.S. Standard Tools Kit All standard tools needed to properly maintain and service your crane. (Does not include torque wrench.) Field Service Factory-trained service experts are always ready to help maintain your crane s peak performance. For a worldwide listing of dealer locations, please consult our website at: www.manitowoccranegroup.com Available from your Authorized Manitowoc Cranes Distributor, these VS videos are available in NTSC, PA and SECAM formats. Your Capacity Chart Video Respect the imits Video Crane Safety Video Inspection/Repair Video Crane CARE Package Manitowoc has assembled all of the available literature, CD s and videos listed above plus several Manitowoc premiums into one complete Crane CARE Package. 39 Technical Support Manitowoc s dealer network and factory personnel are available 4 hours a day, 7 days a week, 365 days a year to answer your technical questions and more, with the help of computerized programs that simplify crane selection, lift planning, and ground-bearing calculations. For a worldwide listing of dealer locations, please consult our website at: www.manitowoccranegroup.com Technical Documentation Manitowoc has the industry s most extensive documentation, and the easiest to understand, available in major languages and formats that include print, disk and videotape. Additional copies available through your Authorized Manitowoc Distributor. Crane Operator s Manual Crane Parts Manual Crane Capacity Manual Crane Vendor Manual Service Manual (EPIC) uffing Jib Operator s/parts Manual Capacity Chart Manual - Attachments CD rom versions of the Operator s and Parts Manuals are shipped with each crane. Also available are the following CDs: Crane CARE Owner CD Ground Bearing Pressure Estimator CD Crane Selection and Planning Software (CompuCRANE ) EPIC Crane ibrary CD consisting of capacity charts, range diagrams, wire rope specifications, travel specifications, crane weights, counterweight arrangements, luffing jib raising procedures, operating range diagrams, drum and lagging charts, boom rigging drawings, jib rigging drawings, outline dimensions and wind condition charts.