Goulds Pumps Marlow Series 2EVP Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents STANDARD UNIT INCLUDES: Goulds Pumps is a brand of ITT Corporation. www.goulds.com Engineered for life PUMP: Heavy-duty cast iron construction, with 2" NPT female threaded, in-line suction and discharge ports. This compact, vertical design is self-supporting and requires a minimum of fl oor space. The self-priming feature allows the pump to be mounted above the liquid and suction lifts of 1' to 2' can be achieved, depending on the liquid and the pump model. Diffuser priming eliminates the need for a check valve and reduces radial loads insuring longer bearing life. These pumps are sealed by a self-lubricating, Viton mechanical shaft seal. When used on a suction lift any leakage that may occur will be down into the pump rather than up the motor shaft as the seal is on the suction side of the impeller. MOTOR: Single phase motors are 6 cycle, 115/2 volt, except 2 HP explosion proof motors which are 2 volt only. Three phase motors are 6 cycle, 2/46 volt and all are 45 RPM motors. All explosion proof motors are Class I, Group D, Code: TB. OPTIONAL MOUNTING: All models fi t the Marlow Pumps lightweight, two wheel chassis. Kit illustrated in Section 8. OPTIONAL SEAL: Kalrez mechanical seals are available. Contact factory for more information. 1
PERFORMANCE Capacity in U.S. Gallons per Minute Pump Model Size Total Head in Feet 1 2 4 5 6 7 8 9 1 9A 112 9 72 2 1A 6 58 51 6 12 2EVP 11A 1 94 84 72 55 15 12A 115 18 1 9 78 65 41 17A 121 12 116 11 12 91 77 6 2 NOTE: Capacities listed are for 5 ft. dynamic suction lift. With higher lifts, capacities will be lower and on fl ooded suction, capacities will be higher. Maximum Static Suction Lift Cold, Clear Water at Sea Level Model 9A 1A 11A 12A 17A S.L. in Feet 12 14 11 2 2 STANDARD CONSTRUCTION Casing Close Grained Cast Iron Base Close Grained Cast Iron Impeller Nickel Plated Cast Iron Diffuser Nickel Plated Cast Iron Shaft Seal 5 / 8" Viton, Stainless and Brass, Self-Lubricating SPECIFICATIONS Pump Tank Capacity 1 Gallon Priming Connection 1" (Plugged) Drain Connection / 8" (Plugged) Working Pressure 1 PSI Elastomers Model EVP Viton TYPE IMPELLER AND SOLIDS SIZE Pump Sizes Type 9A 1A Impeller Open Closed 11A 12A 17A Maximum Size Solids Handled 7 16" 16" 16" 16" 16" 2
CROSS SECTION Key Description Key Description 1 Drain Plug 7 Diffuser 2 Cover 8 Gasket, Diffuser Gasket, Cover 9 Impeller Shim 4 Impeller Nut 1 Impeller Spacer 5 Impeller Washer 11 Seal Assembly 6 Impeller 12 Tank
PERFORMANCE CURVES EVP-A Units Designed and Powered for Petroleum Bulk Plant Usage The performance curves shown in this manual and other published literature were taken from actual tests of standard production pumps and reflect an average performance of the pumps indicated. 2 1 TOTAL HEAD IN POUNDS PER SQUARE INCE - SP. GR..72 2 1 TOTAL HEAD IN POUNDS PER SQUARE INCE - SP. GR..85 4 2 1 1 75 5 25 1A TYPE: 2EVP - A LIQUID: SP. GR..72-.85 SPEED: 45 RPM 9A 11A 17A 12A 25 5 75 1 125 1 2 15 6 5 MODEL: 2EVP - 9A SPEED: 45 RPM POWER: 1 HP MOTOR 1 5 4 2 1 SP. GR. 1. SP. GR..85 SP. GR..72 8 2 4 1 2 4 6 8 1 12 12 1 8 6 4 4 1 2
PERFORMANCE CURVES EVP-A Units Designed and Powered for Petroleum Bulk Plant Usage The performance curves shown in this manual and other published literature were taken from actual tests of standard production pumps and reflect an average performance of the pumps indicated. 1 8 MODEL: 2EVP - 1A SPEED: 45 RPM POWER: 1 HP MOTOR 2 1 6 4 2 SP. GR. 1. SP. GR..85 SP. GR..72 1 2 4 5 6 5 1 1 2 1 1.5 1..5 1 8 MODEL: 2EVP - 11A SPEED: 45 RPM POWER: 1 1 /2 HP MOTOR 2 1 6 4 SP. GR. 1. SP. GR..85 SP. GR..72 1 1.5 2 2 1. 2 4 6 8 1 12 1.5 1 2 5
PERFORMANCE CURVES EVP-A Units Designed and Powered for Petroleum Bulk Plant Usage The performance curves shown in this manual and other published literature were taken from actual tests of standard production pumps and reflect an average performance of the pumps indicated. 1 8 MODEL: 2EVP - 12A SPEED: 45 RPM POWER: 1 1 /2-2 HP MOTOR 2 1 6 4 SP. GR. 1. SP. GR..85 SP. GR..72 2.5 1 2. 2 2 4 6 8 1 12 2 1 1.5 1..5 1 2 12 1 MODEL: 2EVP - 17A SPEED: 45 RPM POWER: 2 HP MOTOR 2 1 8 6 4 2 SP. GR. 1. SP. GR..85 SP. GR..72 2 4 6 8 1 12 1 2 1 2 1 6 1 2
DIMENSIONS 9 11 /2 /8 9 5 /8 FOR 1 1 /2 AND 2 HP, 1Ø ONLY /4-14 NPT 6 /16 /4-14 NPT 6 1 /2 4787 G A MAX. 4 7 /16 4 7 /16 15 /8 7 /8 9 7 /8 2 NPT SUCTION (FEMALE) 9 /16 DIA. (4) MTG. HOLES ON 11 1 /4 DIA. B.C. 45º FROM CL OF PIPE CONNECTIONS Dimensions shown in inches. 2 NPT DISCHARGE (FEMALE) 12 1 /8 DIA. All Motors 56 Frame Except 1½" and 2 HP, 1Ø Which Are 184 Frame Explosion Proof Motors HP Phase Cycle A 1 1½ 2 Dimensions may vary by manufacturer. 1 2½" 19½" 1 26 6 1 8" 2½" 26 1 8" 21 7 8" NOTE: These dimensions are not to be used for construction purposes without formal factory approval. 7
Goulds Pumps and the ITT Engineered Blocks Symbol are registered trademarks and tradenames of ITT Corporation. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. MB275 April, 27 27 ITT Corporation Engineered for life 8