Table of Contents D. Air modules...d-2 AQ2 Air module...d-2 1. Product Overview...D-2 2. Installation...D-3 2.1 Module Installation... D-3 2.2 Module Removal... D- 3. Operation...D-5. Maintenance...D-5.1 Preventive Maintenance... D-5 5. Troubleshooting and Service Procedures...D-6 5.1 Troubleshooting... D-6 5.2 Service Procedures... D-7 5.2.1 Master Side Self Sealing Valve... D-7 5.2.2 Tool Side Self Sealing Valve... D-9 6. Serviceable Parts...D-11 7. Specifications...D-11 8. Drawings...D-12 8.1 AQ2-M AQ2-T... D-12 8.2 AQ2-M AQ7-T... D-13 D-1
D. Air modules AQ2 Air module 1. Product Overview Modules providing air utility are attached to the Master and Tool plates. When the Tool Changer is coupled, the AQ2 Master module passes air supply to AQ2 Tool module for customer tooling. Table 1.1 Air Modules Module Air Ports Valves AQ2-M (2) G 1/2 (2) self sealing check AQ2-T (2) G 1/2 (2) self sealing check AQ7-T (2) G 1/2 (2) unchecked check NOTICE: Self sealing ports are not to be used for vacuum service. 1/2 NPT Air Ports () Figure 1.1 Air modules Self Sealing Check Valve () 9121-AP2-M Self Sealing Check Valve () Common Ledge Mounting Feature 1/2 NPT Air Ports () 9121-AP2-T Shown The Master (AQ2-M) and Tool (AQ2-T) modules each contain () self sealing check valves. Self sealing valves are not to be used for vacuum utility. The AQ2 modules provide () G 1/2 Air ports for customer connections. D-2
2. Installation The air modules are typically installed on Tool Changers by ATI prior to shipment. The steps below outline field installation or removal as required. For detail information refer to Section 8 Drawings. WARNING: Do not perform maintenance or repair on Tool Changer or modules unless the Tool is safely supported or docked in the tool stand, all energized circuits (e.g. electrical, air, water, etc.) are turned off, pressurized connections purged and power discharged from circuits in accordance with the customer s safety practices and policies. Injury or equipment damage can occur with Tool not docked and energized circuits on. Dock the Tool safely in the tool stand, turn off and discharge all energized circuits, purge all pressurized connections, verify all energized circuits are de-energized before performing maintenance or repair on Tool Changer or modules. CAUTION: Air supply should be clean and dry. Supply pressure should not exceed 100 psi and should be filtered 50 micron or better. Connection lines should be properly strain relieved. CAUTION: It is recommended, not to use fasteners with pre-applied adhesive more than three times. Fasteners used more than three times may come loose and cause equipment damage. Discard fasteners used more than three times and install new fasteners with preapplied adhesive. 2.1 Module Installation Tools required: 5 mm Allen wrench (hex key), torque wrench Supplies required: clean rag 1. With the Tool Changer installed, dock the Tool safely in the tool stand and uncouple the Tool Changer to allow clear access to the Master and Tool plates. 2. Turn off and de-energize all circuits (e.g. electrical, air, water, etc.). 3. It may be necessary to clean the mounting surface on the Tool Changer prior to installing the module in order to remove any debris that may be present.. Using the ledge feature, place the module into the appropriate location on the Tool Changer body. Align the module with the Tool Changer using the dowels in the bottom of the ledge feature. 5. If fasteners do not have pre-applied adhesive, apply Loctite 22 to the supplied M6 socket head cap screws fasteners. Install the (2) M6 socket head screws securing the module to the Tool Changer and tighten to 89 in-lbs (10.0 Nm). 6. Connect customer plumbing to the module. 7. After installation is complete, module may be put into normal operation (e.g. electrical, air, water, etc.). D-3
Figure 2.1 Installation and Removal of the module M6 Socket Head Screws 9121-AP2-T Shown Tool Changer 2.2 Module Removal Tools required: 5 mm Allen wrench (hex key) 1. If the Tool Changer is already installed, dock the Tool side of the Tool Changer safely in the tool stand and uncouple the Tool Changer to allow clear access to the Master and Tool plates of the Tool Changer. 2. All customer plumbing connections to the module need to be purged and disconnected. Once the supply lines have been turned off, the self sealing valves on the module can be manually actuated to purge the line pressure. Cover the valves with a rag prior to purging in order to keep the air from impinging upon any person. 3. Prior to removing the module use a marker pen to scribe a line or indication between the Tool Changer and module as a reminder where the module is to be re-installed.. Remove the (2) M6 socket head cap screws and lift the module from the Tool Changer. D-
3. Operation The air modules are designed to pass air utilities from the Master to the Tool for use by the customer s tooling. () self sealing valves are provided on the Master side so that the air circuits do not discharge during tool change and the circuits upstream of the Tool Changer do not have to be closed down prior to tool change.. Maintenance Once installation is completed, the operation of the air modules is generally trouble free. Periodically, the condition of the self sealing valves should be checked. Replace any damaged or degraded components as necessary. Mating surfaces should be keep clean. Use a vacuum to remove any debris and clean in and around the mating surfaces of the modules using a nylon brush (ATI Part Number 3690-000006-60). Lubricate seals periodically with G lubricant. During inspection, ensure that the fasteners attaching the modules to the Tool Changer are secure. WARNING: Do not perform maintenance or repair on Tool Changer or modules unless the Tool is safely supported or docked in the tool stand, all energized circuits (e.g. electrical, air, water, etc.) are turned off, pressurized connections purged and power discharged from circuits in accordance with the customer s safety practices and policies. Injury or equipment damage can occur with Tool not docked and energized circuits on. Dock the Tool safely in the tool stand, turn off and discharge all energized circuits, purge all pressurized connections, verify all energized circuits are de-energized before performing maintenance or repair on Tool Changer or modules..1 Preventive Maintenance A visual inspection and preventive maintenance schedule is provided in Table.1. Table.1 Preventive Maintenance Schedule Inspection Schedule Action Required Weekly Clean and inspect 6 months or 500,000 cycles Seal replacement Checklist Weekly Maintenance: гг Clean mating surfaces. гг Inspect modules for air leaks. Replace components as necessary. 6 months or 500,000 cycle Maintenance: гг гг Remove and replace self sealing valve O-ring seals in both the Master and Tool Module. During O-ring and seal replacement inspect valve stem and dowel pin for straightness. During O-ring and seal replacement re-lubricate bores. Refer to Section 5.2.1 Master Side Self Sealing Valve and Section 5.2.2 Tool Side Self Sealing Valve. Inspect the mounting fasteners for tightness, tighten if loose refer to Section 2.1 Module Installation. D-5
5. Troubleshooting and Service Procedures The following section provides troubleshooting information to help diagnose conditions with the Tool Changer and service procedures to help resolve these conditions. WARNING: Do not perform maintenance or repair on Tool Changer or modules unless the Tool is safely supported or docked in the tool stand, all energized circuits (e.g. electrical, air, water, etc.) are turned off, pressurized connections purged and power discharged from circuits in accordance with the customer s safety practices and policies. Injury or equipment damage can occur with Tool not docked and energized circuits on. Dock the Tool safely in the tool stand, turn off and discharge all energized circuits, purge all pressurized connections, verify all energized circuits are de-energized before performing maintenance or repair on Tool Changer or modules. 5.1 Troubleshooting Refer to the table below for trouble shooting information. Table 5.1 Troubleshooting Symptom Possible Cause Correction Replace seals. Refer to Section 5.2.1 Master Damaged/Worn seals Side Self Sealing Valve and Section 5.2.2 Tool Side Self Sealing Valve. Clean in and around valve components. Debris blocking valve seal Ensure air stream is free of large particulates, filter as necessary. Air Leakage Replace stem. Check module attachment to Tool Changer. Check robot program and Bent stem ensure parallel approach trajectory during Tool Changer coupling. Refer to Section 5.2.1 Master Side Self Sealing Valve and Section 5.2.2 Tool Side Self Sealing Valve. Corrosion Consult ATI for assistance. Poor Flow Modules Won't Couple Air hose supply/return lines or connections damaged or blocked Valve blockage Debris between Tool Change Master and Tool plates or modules. Bent stem, dowel pin Inspect supply/return hoses and connections for damage or blockage, clean/repair/replace as necessary. Inspect valve components and clean/repair as necessary. Refer to Section 5.2.1 Master Side Self Sealing Valve and Section 5.2.2 Tool Side Self Sealing Valve. Clean debris from between Master and Tool Plates and modules. Replace stem, dowel pins as necessary. Check module attachment to Tool Changer. Check robot program and ensure parallel approach trajectory during Tool Changer coupling. Refer to Section 5.2.1 Master Side Self Sealing Valve and Section 5.2.2 Tool Side Self Sealing Valve. D-6
5.2 Service Procedures The following service procedures provide instructions for component replacement and adjustment. 5.2.1 Master Side Self Sealing Valve Parts required: Refer to Section 8 Drawings Tools required: mm Allen wrench (hex key), torque wrench Supplies required: Loctite 222, G lubricant 1. Dock the Tool safely in the tool stand and uncouple the Tool Changer to allow clear access to the Master and Tool plates. Leave the locking mechanism unlocked. 2. Turn off and de-energize all energized circuits (e.g. electrical, air, water, etc.) 3. Remove the self sealing valve assembly (stem, check valve, spring and seals) using a mm Allen wrench. Be careful not to strip the hex on the valve stem during removal. Refer to Figure 5.1.. Clean any lubrication from the check valve, valve stem, and bore in the module housing using a clean rag. 5. Inspect all seals and replaced as required. 6. Inspect the spring in the assembly and replaced as required. 7. Inspect the valve stem for straightness and replaced, if bent. Figure 5.1 Disassemble Self Sealing Master Valve mm Allen Wrench Valve Stem Valve Stem (Inspect) (Inspect) Check Valve Spring (Inspect) (Inspect) Check Valve Bore in Module Housing (Clean) D-7
NOTICE: Do not lubricate the O-ring face seal until after installation. Lubricating O-ring before installation can cause O-ring to blow out during coupling and uncoupling. 8. Lubricate bore in the module housing and the O-ring seals except the face seal as shown in Figure 5.2 with G (Teflon/Petroleum based grease). 9. Install the O-ring on the valve stem. 10. Install the internal O-ring and the outer O-ring on the check valve. 11. Install the non-lubricated O-ring (face seal) into the check valve. Figure 5.2 Master Valve O-ring Installation and Lubrication Valve Stem (Lubricate) (Lubricate) Check Valve (Lubricate) (Face Seal) (No Lubrication) Check Valve Bore in Module Housing (Lubricate) 12. Re-install the valve assembly, all components should be arranged in order as removed. See Figure 5.3. 13. Apply Loctite 222 or similar thread locker to the threaded end of the stem, re-install and tighten to 10 in-lbs (1.1 Nm). The piston will have to be pushed down flush with the mating surface in order to get the stem thread started. 1. Lubricate the installed O-ring (face seal) as shown in Figure 5.3 with G (Teflon/ Petroleum based grease) 15. After repair is complete, return all circuits to normal operation. Figure 5.3 Assemble Self Sealing Master Valve Torque Wrench mm Allen Wrench Valve Stem Apply Loctite 222 (Face Seal) (Lubricate) Check Valve Spring D-8
5.2.2 Tool Side Self Sealing Valve Parts required: Refer to Section 8 Drawings Tools required: snap-ring pliers Supplies required: G lubricant 1. Dock the Tool safely in the tool stand and uncouple the Tool Changer to allow clear access to the Master and Tool plates. Leave the locking mechanism unlocked. 2. Turn off and de-energize all energized circuits (e.g. electrical, air, water, etc.) 3. Remove the retaining ring from the bottom of the tool side module using snap-ring pliers. Remove the self sealing valve assembly (plug, spring, valve, and seals). It may be necessary to remove the tool side module to have access to the plug. Refer to the Section 2.2 Module Removal for instructions for module removal.. Once the retaining ring is removed, the seals on the plug assembly and valve assembly can be inspected and replaced as required. 5. The spring in the assembly should be inspected and replaced as required. 6. The plug assembly contains a dowel pin. The dowel pin should be inspected for straightness, replace the plug assembly if the dowel pin is bent. 7. Clean any excess lubrication from the valve assembly, plug assembly, and bores in the module housing using a clean rag. 8. Lubricate O-ring seals and bores in the module housing with G (Teflon/Petroleumbased grease). Figure 5. Disassemble Self Sealing Tool Valve Snap-Ring Pliers Retaining Ring Plug Assembly Spring (Inspect) Valve Assembly (Inspect) Dowel Pin (Inspect) (Inspect) (Lubricate) Plug Assembly Valve Assembly (Lubricate) Bore in Module Housing (Clean) D-9
9. Install the O-rings on the plug assembly and the valve assembly. 10. Re-install the valve assembly, all components should be arranged in order as removed. Refer to Figure 5.5. NOTICE: Care should be taken not to damage the O-ring around the plug base during installation. 11. After repair is complete, return all circuits to normal operation. Figure 5.5 Assemble Self Sealing Master Valve Snap-Ring Pliers Retaining Ring Plug Assembly Spring Valve Assembly D-10
6. Serviceable Parts See drawings in Section 8 Drawings of this manual. 7. Specifications 9121-AQ2-M Materials of Construction Weight: Self Sealing Valves: Quantity Air Pressure Cv, Min Customer Port Connection 9121-AQ2-T Materials of Construction Weight: Self Sealing Valves: Quantity Air Pressure Cv, Min Customer Port Connection 9121-AQ7-T Materials of Construction Weight: Self Sealing Valves: Quantity Air Pressure Cv, Min Customer Port Connection Table 7.1 AQ2 Module Specifications Pneumatic module with () self sealing valves with ½ G ports connections - Master Side Various - Stainless Steel valve components, aluminum housing, Buna-N seals 2.8 lbs. (1.3 kg) Maximum pressure of 100psi (6.9bar) 3.1 G 1/2 Table 7.2 AQ2 Module Specifications Pneumatic module with () self sealing valves with ½ G ports connections - Tool Side Various - Stainless Steel valve components, aluminum housing, Buna-N seals 2.0 lbs. (0.9 kg) Maximum pressure of 100psi (6.9bar) 3.1 G 1/2 Table 7.3 AQ7 Module Specifications Pneumatic module with () ½ G pass-through ports - Tool Side Various - aluminum housing TBD Maximum pressure of 100psi (6.9bar) 3.1 G 1/2 D-11
8. Drawings 8.1 AQ2-M AQ2-T 158.8 22.2 3X 38.1 8X G 1/2 Ports 6 769-222 / 25 in-lbs 8.7 32.9 2 1 22.2 5.6 7 3 5 Notes: Materials of Construction: 1. Housings - Aluminum 2. Valve Components - Stainless Steel, Bronze & Nitrile Operations: 1. For best results ensure fluids are near neutral ph, minimize fluid particulate size and keep fluid module mating surfaces free and clear of any debris. 2. Checked ports can produce significant forces when under high supply pressures. See product manual regarding proper operating procedure. ITEM NO. QTY. PART NUMBER DESCRIPTION 1 310-00012-01, 19x2 2 310-0001268-01 1MM X 2MM Buna 90A 3 310-0001366-01, AS568-210, N1090 (ELF), D85 310-0001371-01, mm ID x 2mm, Buna-N, D70 5 3610-750501-21 SPRING, 1/2" F/A MASTER 6 3700-20-616 Fluid Module Valve, 1/2, Master 7 3700-20-7621 Fluid Module Poppet,Relieved, 1/2, Master NOTES: UNLESS OTHERWISE SPECIFIED. DO NOT SCALE DRAWING. ALL DIMENSIONS ARE IN MILLIMETERS. Note: Service Kit 9005-20-1321 consists of (1) each of Items 1,2,3 &. Service Kit 9005-20-120 consists of (1) each of Items 1 thru 7. 3rd ANGLE PROJECTION Rev. Description Initiator Date 08 ECO 13199; Removed 9005-20-1198 & 9005-20-1199 Cleat assemblies representations from drawing; Corrected various Kit note errors; Corrected right side view with updated dim's. TBC 3/26/2015 6 52.2 97.8 Approx. Coupled 1 3 2 5 ITEM NO. QTY. PART NUMBER DESCRIPTION 1 310-000123-01, 22x2 2 310-0001269-01, 15x2, D90 3 3610-6203201-21 SPRING, 1/2" F/A TOOL 3690-2000002-11 RETAINING RING, INTERNAL, 1-1/16" 5 3700-20-621 Fluid Module Valve, 1/2, Tool 6 9005-20-1831 1/2" Port Plug Assembly, Tool Note: Service Kit 9005-20-1322 consists of (1) each of Items 1 & 2. Service Kit 9005-20-121 consists of (1) each of Items 1 thru 6. 1031 Goodworth Drive, Apex, NC 27539, USA Tel: +1.919.772.0115 Email: info@ati-ia.com Fax: +1.919.772.8259 www.ati-ia.com ISO 9001 Registered Company DRAWN BY: D. Wagner, 3/26/07 CHECKED BY: DKL, 3/29/07 PROPERTY OF ATI INDUSTRIAL AUTOMATION, INC. NOT TO BE REPRODUCED IN ANY MANNER EXCEPT ON ORDER OR WITH PRIOR WRITTEN AUTHORIZATION OF ATI. TITLE AQ2-M, AQ2-T Module Drawing SCALE SIZE DRAWING NUMBER REVISION 070206-5 1 1 1:2 B 08 PROJECT # SHEET OF 9630-20-AQ2 D-12
8.2 AQ2-M AQ7-T Rev. Description Initiator Date 158.8 01 Initial Drawing DJB 11/18/2015 3X 38.1 G 1/8 Plug 22.2 9121-AQ2-M X G 1/2 Ports 6 2 769-222 / 25 in-lbs 32.9 22.2 8.7 5.6 52.2 98 Approx. Coupled 1 7 X G 1/2 Ports 9121-AQ7-T 5 3 5 Notes: 6 8 Materials of Construction: 1. Housings - Aluminum 2. Valve Components - Stainless Steel, Bronze & Nitrile 1 Operations: 1. For best results ensure fluids are near neutral ph, minimize fluid particulate size and keep fluid module mating surfaces free and clear of any debris. 2. Checked ports can produce significant forces when under high supply pressures. See product manual regarding proper operating procedure. Note: Service Kit 9005-20-1321 consists of (1) each of Items 1,2,3 &. Service Kit 9005-20-120 consists of (1) each of Items 1 thru 7. NOTES: UNLESS OTHERWISE SPECIFIED. DO NOT SCALE DRAWING. ALL DIMENSIONS ARE IN MILLIMETERS. DRAWN BY: CHECKED BY: D. Bohle 11/18/2015 M. Gala 11/19/2015 TITLE 1031 Goodworth Drive, Apex, NC 27539, USA Tel: +1.919.772.0115 Email: info@ati-ia.com Fax: +1.919.772.8259 www.ati-ia.com ISO 9001 Registered Company PROPERTY OF ATI INDUSTRIAL AUTOMATION, INC. NOT TO BE REPRODUCED IN ANY MANNER EXCEPT ON ORDER OR WITH PRIOR WRITTEN AUTHORIZATION OF ATI. AQ2-M, AQ7-T Module Drawing 3rd ANGLE PROJECTION SCALE SIZE DRAWING NUMBER REVISION 1 1 1:2 B PROJECT # SHEET OF 9630-20-AQ2M AQ7T 01 D-13