DETENTION ACCESSORIES Engineered to last 20 years to life.
Designed with Durability in Mind PDI s standard and custom specification detention accessories are the most the cost-effective solution for new construction or retrofits, and contribute to safer correctional environments. Fabricated with hard wearing steel or stainless steel for long-lasting value, PDI accessories are virtually indestructible. Resistance to scratching, dents, and markup withstand years of use and abuse. Polished surfaces are easier to clean and disinfect, helping reduce the spread of germs. Multi gauge steel mounting plates provide secure installation in any environment. Table of Contents Key Cabinet...2 Long Gun Locker...3 Pistol Locker - Standard...4 Pistol Locker - Tilt...5 Package Pass...6 Food Pass...7 Safety Shelves with Hooks...8 Ball & Pin Safety Hook...9 Safety Hook...10 Speaker Port...11 One Piece Mirrors...12 Two Piece Mirrors...13 Soap dish...14 Toilet Paper Holder...15 Grab Bars...16 Safe Bar...17
KEY CABINET KC1000 Door hung on continuous steel piano hinge and flanged 1 all around for additional strength. Equipped with interior swinging 10 gauge steel leaf panels for maximum key storage. Coated with factory primer for finish painting. Shell: 10 gauge steel Door: 10 gauge steel plate Key racks: 14 gauge bent steel plates 24 H x 18 5/8 W CAPACITY 180 Key Capacity 300 Key Capacity 405 Key Capacity 60 Paracentric Keys 60 Paracentric Keys 120 Paracentric Keys 120 Mogul Keys 120 Mogul Keys 180 Mogul Keys 120 Builders Keys 105 Builders Keys Mounting holes provided for installation with 3/8 anchors. Anchors not provided by PDI. KC1000 Custom key capacity per project requirements. Powder coat finish. Page 2
LONG GUN LOCKER LG1000 Secure long gun locker with 3, 4, 6 or 8 compartments for rifles or shotguns. Doors on 11/2 open x.060 continuous piano hinge with.125 pin, and ABLOY cam locks Shell: 10 gauge steel Doors: 10 gauge plate Vary by specification 1/2 diameter anchor holes provided in back of unit for wall mounting. Anchors not by PDI. Custom capacity and size based on project requirements. Factory red oxide primer finish. Stainless steel with polished finish. Powder coat finish. Custom compartments. LG1000 714.288.1770 sales@pdidet.com pdidet.com Page 3
PISTOL LOCKER - STANDARD PL1000 Secure pistol locker equipped with cam locks. Doors are hung on continuous steel piano hinges and include and internal door stop mechanism. Two keys supplied per compartment and two master keys supplied per unit. Coated with factory primer. Angle frame can be shipped loose for semi-recessed installation and field welded in place. Mounting Shell: 10 gauge steel Doors: 10 gauge plate 7/16 diameter holes for mounting. Locker dimensions vary 21/2 x 21/2 x 10 gauge angle frame PL1000 Mounting plates provided with 7/16 diameter holes for 3/8 anchors. Anchors not by PDI. Custom capacity and size based on project requirements. Locker compartment tags. Stainless steel. Galvanized steel. Powder coat finish. Page 4
PISTOL LOCKER - TILT PL2000 Secure pistol locker with tilt out compartments equipped with Master snap locks. Compartments are hung on continuous steel piano hinges and include internal stop bars. Two keys supplied per compartment and two master keys supplied per unit. Coated with factory primer finish. Angle frame can be shipped loose for semi-recessed installation and field welded in place. Mounting Shell: 10 gauge steel angle frame Doors: 10 gauge plate 7/16 diameter holes for mounting Locker dimensions vary 21/2 x 21/2 x 10 gauge angle frame PL2000 Mounting plates provided with 7/16 diameter holes for 3/8 anchors. Anchors not by PDI. Custom capacity and size based on project requirements. Locker compartment tags. Stainless steel. Galvanized steel. Powder coat finish. 714.288.1770 sales@pdidet.com pdidet.com Page 5
PACKAGE PASS PP1000 Package Pass doors are connected with a control mechanism allowing only one door to be open at a time. Secure side door equipped with a Master snap lock and door pull. Coated with factory primer for finish painting. 11 gauge doors 10 gauge body 7 gauge plate door Maximum package size 19 W x 13 H Door is equipped with two 7 gauge angle collars for installation. PP1000 Powder coat. Stainless steel door. Page 6
FOOD PASS FP1000 Food Pass door is on a continuous piano hinge. Adjoining slip collars create a secure pass through. Food pass face prepped for a detention snap lock. Coated with factory primer for finish painting. 12 gauge assembly and handle 7 gauge plate door 12 3/8 H x 19 5/16 overall 4 1/2 H x 15 W pass thru opening Create cut out for food pass and either field weld or thru-bolt. Powder coat. All stainless steel. Galvanized material. FP1000 714.288.1770 sales@pdidet.com pdidet.com Page 7
SAFETY SHELVES WITH HOOKS SF1000/SF2000 7 gauge thick hook bolted to 10 gauge bracket with non-removable security screw and tension washer 8 D x 6 H x 18 W 5 x11 /2 x 10 gauge (shelf ) Wall mounted with 5/16 diameter mounting holes and 1/4 anchors. Anchors not by PDI. Powder coat finish. All stainless steel. All galvanized material. SF2000 SF1000 Page 8
BALL & PIN SAFETY HOOK SH2000 Stainless steel body and round ball hook with steel back strap and nylon bushing. Up to 4 hooks. 14 gauge stainless steel 16 gauge stainless steel back strap 4 H x 4 W x 1 D SH2000 Punched and countersunk for wall mounting with 1/4 anchors.. Anchors not by PDI. Single, 2, or 4 hook strip. Powder coat finish. 714.288.1770 sales@pdidet.com pdidet.com Page 9
SAFETY HOOK SH1000 Hook bolted to bracket with non-removable security screw and tension washers. 10 gauge mounting plate and bracket 7 gauge hook 5 H x 11/2 W 5/16 diameter holes for wall mounting with 1/4 anchors. Anchors not by PDI. SH1000 Powder coat finish. All stainless steel. All galvanized material. Page 10
SPEAKER PORT SP1000 Stainless steel face plate with perforated pattern, connected with a pass-proof segment. Polished to a #4 finish. Ships with security screws for assembly. Stainless steel 61/2 diameter x 1/8 Install face plates from opposing sides of glass. Fasten both face plates together with provided security screws. SP1000 714.288.1770 sales@pdidet.com pdidet.com Page 11
ONE PIECE MIRRORS MR1000/MR1001 One piece mirrors are stamped stainless steel with a polished mirror finish. LARGE ONE-PIECE MIRROR Frame 16 gauge steel Mirror 20 gauge stainless steel Frame: 91/2 W x 111/4 H x 5/16 D Mirror: 10 W x 14 H SMALL ONE-PIECE MIRROR Frame 14 gauge steel Mirror 20 gauge stainless steel Frame: 10 W x 111/2 H x 1/4 D Mirror: 8 W x 93/4 H Eight 5/16 diameter countersunk holes provided for installation with 1/4 flat head anchors. Anchors not by PDI. Mirror can be installed onto optional mounting plate or embed plate which ships with eight 1/4-20 stainless steel FH security screws for installation. MR1001 MR1000 Mounting plate. Embed plate. Page 12
TWO PIECE MIRRORS MR2000/MR2001 Two Piece Mirrors are composed of a stamped chrome plated and polished frame with mirror insert. Mirror is steel sheet polished to a mirror finish approximating that of glass. LARGE 2-PIECE MIRROR Frame 16 gauge steel Mirror 20 gauge stainless steel Frame: 121/2 W x 181/2 H x 5/16 D Mirror: 10 W x 14 H SMALL 2-PIECE MIRROR Frame 14 gauge steel Frame: 10 W x 111/2 H x 5/16 D Mirror: 8 W x 91/2 H MR2000 Eight 5/16 diameter countersunk holes provided for installation with 1/4 flat head anchors. Anchors not by PDI. Mirror can be installed onto optional mounting plate or embed plate which ships with Eight 1/4-20 stainless steel FH security screws for installation. MR2001 Mounting plate. Embed plate. 714.288.1770 sales@pdidet.com pdidet.com Page 13
SOAP DISH SD1000 14 gauge stainless steel with exposed surfaces in satin finish Mounting Plates: 11 gauge stainless steel 71/2 W x 55/8 H x 23/4 D Provide 6 W x 4 H x 3 D wall opening for installation. Chase mounted with rear threaded studs and flat bar back plate. Face mounted with 5/16 diameter holes for 1/4 button-head anchors. SD1000 Page 14
TOILET PAPER HOLDER TP1000 14 gauge stainless steel one-piece drawn, seamless construction with exposed surfaces in satin finish 7 W x 7 H x 49/32 D Provide 53/4 diameter x 41/4 D wall opening for installation. Unit can be chase mounted or face mounted. Chase mounted with rear threaded studs and flat bar back plate. Face mounted with 5/16 diameter holes for 1/4 button-head anchors. TP1000 714.288.1770 sales@pdidet.com pdidet.com Page 15
GRAB BARS GB1000/GB2000 Stainless steel detention grab bars for use in handicap accessible areas. Tube: 18 gauge, type 304 stainless steel Mounting Plates: 11 gauge stainless steel Tube: 11/2 diameter Mounting Plates: 4 diameter Three 7/16 diameter holes drilled in mounting plates for anchors. Anchors not by PDI. GB1000 Closure Plate - bottom gap between wall and grab bar closed with a 10 gauge plate with 1/4 diameter holes for drainage. GB2000 Page 16
SAFE BAR SB1000 Continuous extruded aluminum grab bar, hard-coat anodized. Extruded 6063-T52 aluminum 11/2 diameter grab area 11/2 gap from grab area and wall 7/16 diameter holes for 3/8 anchors. Anchors not by PDI. Safe bar end caps. SB1000 714.288.1770 sales@pdidet.com pdidet.com Page 17
Headquarters 577 N. Batavia Orange, CA 92868 714 288 1770 714 288 1769 fax sales@pdidet.com pdifurn 0513