flowserve.com Kämmer Series 020000 Split Body s
Description Kämmer Series 020000 are split body style valves manufactured from forged material. This engineering design easily adapts to meet application requirements. Furthermore this design makes the valves easy to clean and maintain. Series 020000 globe valve Series 023000 3-way valve Series 021000 angle valve
flowserve.com Technical Data body style Characteristics Globe, angle, 3-way Equal%, Linear, On - Off Rangeability See table on page 5 Seat leakage Material for plug / seat See table on page 5 PTFE soft seat T = max. 150 C (+300 F) seat with PTFE insert C vs 0.1-2.5 Packing Body gasket Extensions C vs values See table on page 5 Body material 1.4571 Connections* ANSI sizes: Class 150-300 Class 600-2500 *Tube fittings, weld ends and other connections on request. 0.01% of rated C vs value, Class IV acc. to DIN IEC 534 - higher requirements on request PTFE for temperatures up to +200 C (+392 F) Grafoil for temperatures over +200 C(+392 F) PTFE packing for oxygen service Packing according to German Clean Air Act (TA-Luft) PTFE for temperatures up to +200 C(+392 F) 316Ti/Grafoil and Grafoil for temperatures over +200 C(+392 F) Standard, normalizing fins, bellows seal, cryogenic ½ ¾ 1 X X X X Threaded ISO 228 - G ½ or NPT ½, Class 150-2500 3
Designs with cryogenic extension with bellows seal 4 Standard trim Low noise cage trim Ceramics or tungsten carbide plug tip and seat Trim with PTFE soft seat, T = max. 150 C (300 F)
Turbulent? Reynolds entfernen? flowserve.com Standard C vs Values Cvs values (turbulent) Stroke mm (in.) Stem diameter mm (in.) Seat diameter mm (in.) Rangeability* Plug material, standard Seat material, standard Characteristics, lin Characteristics, equal% Tungsten carbide; Hastelloy C; Ceramics Alternative materials for seat/plug Nickel; Monel; Titanium; Alloy 6 0.00063 0.00079 - X - - 10 6 2 0.00098 25:1 Alloy 6 1.4122 - X - - (0.39) (0.24) (0.08) 0.00012 - X - - 0.00015 - X - - 0.00019 - X - - 0.00023 - X - - 10 6 2 0.00029 25:1 Alloy 6 1.4122 - X - - (0.39) (0.24) (0.08) 0.00036 - X - - 0.00045 - X - - 0.00056 - X X - 0.00075 - X X - 10 6 2 0.00098 25:1 Alloy 6 1.4122 - X X - (0.39) (0.24) (0.08) 0.0013 - X X - 0.0017 - X X - 0.0022 - X X - 0.0029 - X X - 10 6 2 0.0038 25:1 Alloy 6 1.4122 - X X - (0.39) (0.24) (0.08) 0.0054 - X X - 0.0079 - X X - 0.013 * For calibrating conditions - X - - 0.020 10 6 3 0.029 50:1 Alloy 6 1.4571 (0.39) (0.24) (0.12) 0.047 0.074 0.12 3 0.19 10 6 (0.12) 0.29 50:1 1.4571 1.4571 (0.39) (0.24) 0.47 4.5 0.74 (0.18) 1.2 7 1.9 10 6 (0.28) 50:1 1.4571 1.4571 (0.39) (0.24) 10 2.9 (0.39) 5
Dimensions mm (in.) Bonnets / extensions Body designs F F B B F A C A Standard Normalising fins Bellows seal Globe valve Angle valve 3-way valve Dimension F Connection Standard Fins Dimensions for valves with cryogenic extensions on request. Dimension A size Bellows PN 10-100 Bellows PN 160-250 All valves 45 (1.77) 85 (3.35) 230 (9.0) 305 (12.0) ANSI Flange (RF)* Class 150 Class 300 Class 600 Cl. 900/1500 Class 2500 ½ 178 (7.00) 190 (7.48) 203 (7.99) 216 (8.50) 264 (10.39) ¾ 181 (7.13) 194 (7.64) 206 (8.11) - - 1 184 (7.24) 197 (7.76) 210 (8.27) - - Dimension B size ANSI Flange (RF)* Class 150 Class 300 Class 600 Cl. 900/1500 Class 2500 ½ 89 (3.50) 95 (3.74) 102 (4.00) 108 (4.25) 132 (45.20) ¾ 90 (3.54) 97 (3.82) 103 (4.05) - - 1 92 (3.62) 98 (3.85) 105 (4.13) - - Dimension C ANSI Flange (RF)* size Class 150 Class 300 Class 600 Cl. 900/1500 Class 2500 ½ 89 (3.50) 95 (3.74) 101.5 (4.00) 108 (4.25) 132 (5.20) ¾ 90.5 (3.56) 97 (3.82) 103 (4.10) - - 1 92 (3.62) 98.5 (3.88) 105 (4.13) - - 6 * Face-to-face dimensions of valves with other flange facings on request.
flowserve.com Weights kg (lb.) series size ANSI Flange Class 150 300 600 900-2500 020000 Standard 020100 Fins 020300 Bellows 023000 Standard 023100 Fins ½ 3.3 (7.3) 3.8 (8.4) 4.0 (8.8) 8.0 (17.6) ¾ 3.7 (8.2) 4.8 (10.6) - - 1 4.4 (9,7) 5.5 (12.1) - - ½ 3.5 (7.7) 4.0 (8.8) 4.2 (9.3) 8.2 (18.0) ¾ 3.9 (8.6) 5.0 (11.0) - - 1 4.5 (9.9) 5.7 (12.6) - - ½ 4.4 (9,7) 4.9 (10.8) 5.1 (12.2) 9.1 (20.1) ¼ 4.8 (10.6) 5.9 (13.0) - - 1 5.4 (11.9) 6.6 (13.4) - - ½ 3.9 (8.6) 4.6 (10.1) 5.0 (11.0) 9.0 (19.8) ¾ 4.5 (9.9) 6.2 (13.6) - - 1 5.4 (11.9) 6.9 (15.2) - - ½ 4.1 (9.0) 4.8 (10.6) 5.2 (11.5) 9.2 (20.3) ¾ 4.7 (10.4) 6.4 (14.1) - - 1 5.6 (12.3) 7.1 (15.7) - - Weights for valves with cryogenic extensions on request. Code 0 2 0 0 P 3 020 021 023 Body design Bonnets / extensions Actuator Series 0 Standard Globe valve 020 000 1 Normalising fins Angle valve 021 000 3 Bellows seal 3-way valve 023 000 5 Cryogenic extension H2, H3 Manual handwheel P2, P3 Pneumatic, Series 2 37, 38 Pneumatic, Series 4 E2, E3 Electric 7
Worldwide Regional Headquarters Flowserve Corporation Flow Control 1350 N. Mt. Springs Parkway Springville, UT 84663 USA Phone: +1 801 489 8611 Fax: +1 801 489 3719 Flowserve (Austria) GmbH Control s - Villach Operation Kasernengasse 6 9500 Villach Austria Phone: +43 (0)4242 41181 0 Fax: +43 (0)4242 41181 50 Your contact: Flowserve India Controls Pvt. Ltd Plot # 4, 1A, E.P.I.P, Whitefield Bangalore Kamataka India 560 066 Phone: +91 80 284 10 289 Fax: +91 80 284 10 286 Kämmer Products Europe, Middle East, Africa, Asia, Pacific FCD KMENBR2020-01 08/08 Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Flowserve product is designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve products should be aware that Flowserve products might be used in numerous applications under a wide variety of industrial service conditions. Although Flowserve can (and often does) provide general guidelines, it cannot provide specific data and warnings for all possible applications. The purchaser/user must therefore assume the ultimate responsibility for the proper sizing and selection, installation, operation, and maintenance of Flowserve products. The purchaser/user should read and understand the Installation Operation Maintenance (IOM) instructions included with the product, and train its employees and contractors in the safe use of Flowserve products in caonnection with the specific application. While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes only and should not be considered certified or as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to be construed as a warranty or guarantee, express or implied, regarding any matter with respect to this product. Because Flowserve is continually improving and upgrading its product design, the specifications, dimensions and information contained herein are subject to change without notice. Should any question arise concerning these provisions, the purchaser/user should contact Flowserve Corporation at any one of its worldwide operations or offices. 2000 Flowserve Corporation, Irving, Texas, USA. Flowserve is a registered trademark of Flowserve Corporation. Flowserve Essen GmbH Manderscheidtstr. 19 45141 Essen Germany Phone: +49 (0)201 8919 5 Fax: +49 (0)201 8919 662 Kämmer Products Americas Flowserve (FCD) Kämmer s INC. 1300 Parkway View Drive Pittsburgh, Pa 15205 USA Tel.: +1 412 787 8803 Fax: +1 412 787 1944 8