U S A INSTALLATION GUIDE EP400 / E8-B

U S A INSTALLATION GUIDE EP400 / E8-B www.easycar-.com

Before Beginning the Installation 1. Wire Connection Guides Please read this entire installation guide before beginning the installation. The installation of this push button remote start system requires interfacing with many of the vehicle s systems. Many new vehicles use low-voltage or multiplexed systems that can be damaged by low resistance testing devices, such as test lights and logic probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before making connections. Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid disconnecting the battery if possible. Many airbag systems display a diagnostic code through their warning lights after they lose power. Disconnecting the battery requires this code to be erased, which can require a trip to the dealer. Roll down a window to avoid being locked out of the car. Heavy Gauge, 10-pin Connector (CN1) There are 6 heavy gauge wires coming from the large 6-pin connector. They are used to energize the ignition circuits in the vehicle. It is crucial to ensure that these connections are capable of handling the current demands. For this reason, Scotch- Locks, T-taps and other such connectors are strongly discouraged. CN1/1 YELLOW STARTER OUTPUT After cutting the starter wire, connect the YELLOW wire to the ignition switch wire. This wire supplies power to the starter motor output. CN1/2 WHITE (+) IGNITION 2 This wire is the polarity feed for the ignition 2. (+) 12V with the key ON and 0V in the START position. This wire supplies power to subsidiary accessories such as car audio, lights and to climate control such as air conditioner and heater. If the vehicle is not equipped with this wire, do not connect it. CN1/3 GREEN (+) IGNITION 1 INPUT/OUTPUT Search for a 0 volt wire with the key in the ACC position, (+) 12V wire with the key on the ON position, and (+) 12V wire with the key on the START position. CN1/4 RED/WHITE (+) MAIN POWER 2 Connect to constant (+) 12V source, minimum 30A capacity. CN1/5 BLUE (+) ACC Search for a wire that is 0V with the key in the OFF position, (+) 12V with the key on the ACC & ON position, and 0V with the key on the START position. CN1/6 RED (+) MAIN POWER 1 Connect to constant (+) 12V source, minimum 30A capacity. 4 INSTALLATION GUIDE INSTALLATION GUIDE 5

Door Lock Harness, 6-pin Connector (CN2) Positive Door Lock System CN2/1 BLACK (-) GROUND CN2/ 6 PIN PLUG AFTER MARKET DOOR LOCK SYSTEM Installation Essentiality Matters Door Connection (CN2) CN2/ 3 PIN PLUG OEM DOOR LOCK SYSTEM For the Vehicle with OEM Power Door Lock System For the Vehicle with After Market Power Door Lock System Reverse Polarity System Primary Harness (CN3) CN3/1 YELLOW DOOR UNLOCK OUTPUT CN3/2 GREEN DOOR LOCK OUTPUT Negative Door Lock System Vacuum Door Lock System 6 INSTALLATION GUIDE INSTALLATION GUIDE 7

Negative One-Way System CN3/5 BROWN (+) TRUNK RELEASE OUTPUT When the system receives the code controlling trunk release output for longer than 1.5 seconds, the BROWN wire supplies an output as long as the transmission continues. This is typically used to operate a trunk/hatch release or other relay-driven function. CN3/6 WHITE (+) SIREN OUTPUT Connect this to the BROWN (+) wire of the siren. Positive One-Way System CN3/7 ORANGE (-250mA) KEY TRIGGER OUTPUT For vehicles with an auto escort light, please proceed with the following. 1) With the key out from the key box, find the (+) 12V wire and cut the wire. 2) Directly connect the (-) side of the cut wire to the CN3/7 wire. CN3/8 BLUE (-) PARKING LIGHT OUTPUT This wire should be connected to the parking light (-) wire in the vehicle. CN3/3 VIOLET (+) PARKING LIGHT OUTPUT This wire should be connected to the parking light (+) wire in the vehicle. CN3/4 GRAY (+) KEY TRIGGER OUTPUT For vehicles with an auto escort light, please proceed with the following. 1) With the key out from the key box, find the (+) 12V wire and cut the wire. 2) Directly connect the (+) side of the cut wire to the CN3/4 wire. CN3/9 VIOLET/WHITE (-250mA) STATUS/BYPASS CN3/10 BLACK (-) GROUND 8 INSTALLATION GUIDE INSTALLATION GUIDE 9

Additional Harness (CN4) CN4/1 GREEN (+) TACHOMETER INPUT WIRE This input provides the module with information about the engine s revolutions per minute (RPMs). It can be connected to the uncommon colored wire of the fuel injector, the crankshaft position sensor, the camshaft position sensor or the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy ignition systems locating a proper signal may be more difficult. It will shows lower than 5V without engine running (with the key ON), 7V-14V with engine running. (This wire can be utilized as a tach sensing wire. Please confirm the dip switch on the main unit is in correct position.) CN4/2 BROWN (+) PARKING LIGHT INPUT Connect this wire to parking light (+). This wire is connected to prevent the vehicle from discharging. When the parking light or headlight is ON during the arming stage, it sends warning signal to the transmitter. (Pager model ONLY) CN4/5 RED/BLACK (-) DOOR TRIGGER Most vehicles use negative door trigger circuits. Connect the RED/BLACK wire to a wire that shows ground when any door is opened. In vehicles with factory delays on the dome light circuit, there is usually a wire that is unaffected by the delay circuitry. CN4/6 WHITE (-) PARKING BRAKE/NEUTRAL SAFETY INPUT (Automatic transmission) Connect this wire to a ground source when the gear is in the Parking position or Emergency brake is applied. (Manual transmission) Connect this wire to a ground source when the Emergency brake is applied. This input MUST rest at ground in order for the remote start system to operate. IMPORTANT! Always verify that the vehicle cannot be started in ANY drive gear and that the override switch is functioning properly. CN4/3 YELLOW (+) FOOT BRAKE (BRAKE SHUTDOWN WIRE) This wire MUST be connected to the vehicle s brake light wire. This is the wire that shows (+) 12V when the brake pedal is depressed. The remote start is disabled or shuts down any time the brake pedal is depressed. CN4/7 BLUE (+) SYSTEM TURN ON Connect this wire to the (+) 12V. This is Push Button Start key signal wire. CN4/8 ORANGE/BLACK (-) DIESEL WAIT TO START INPUT Connect this wire to the wire in the vehicle that sends the signal to turn on the Wait- To-Start bulb in the dashboard. In most diesels the wire is negative (ground turns on the bulb) and the ORANGE/BLACK wire can be directly connected to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the bulb) a relay must be used to change the polarity. CN4/4 RED (+) DOOR TRIGGER This wire is used in vehicles that have a positive (+) switched dome light circuit. Connect the RED wire to a wire that shows (+) 12V when any door is opened, and ground when the door is closed. CN4/9 VIOLET/BLACK (-) TRUNK TRIGGER INPUT This input responds with an instant (-) trunk trigger. 10 INSTALLATION GUIDE INSTALLATION GUIDE 11

Easy Door Lock Sensor, LED Light Connector (CN5) Easy Door Lock Sensor Doors can be locked (armed) or unlocked (disarmed) without the remote or car keys with this function. Simply input the 4 digit pass-code by knocking on the Easy Door Lock Sensor on the front windshield. ** On the pager model (E8-B), knocking twice on the sensor will send a call signal to the pager remote. However, it will not operate when the vehicle is on the ON position nor when the engine is running. LED Light The 10 digit blue LED displays various functions such as arming, disarming, valet mode and emergency status (panic, shock, and theft). Start Button (CN8) 1. Push button ON/OFF 1-1) Engine ON To start your vehicle, press the brake and press the Push-to-Start button. The STOP will illuminate to red. Once the parking brake (automatic transmission) or the emergency brake (manual transmission) is released, the <Ignition On> <Ignition Off> red illumination will disappear. Once the red "STOP" illumination disappears, you will not be able to stop the engine. Dual Shock Sensor (CN6) Install the sensor in a central location and adjust its sensitivity after opening the door in accordance with different shocks and status of LEDs on the shock sensor. It senses shocks by two steps (strong and weak shock). Antenna Module (CN7) 1-2) Engine OFF To turn your engine off, press the brake and press the Push-to-Start button. Once the parking brake (automatic transmission) or the emergency brake (manual transmission) is engaged, the green illumination will appear on START. 2. OFF ACC ON OFF 2-1) ACC To enable the vehicle in the ACC mode, press the Push-to-Start button once without pressing on the brake Mount the antenna horizontally at the top left or right corner of the front windshield. The transmitting distance may decrease if the vehicle has a UV protective coating on the windshield. 2-2) ON To enable the vehicle in the Ignition ON mode, press the Push-to-Start button twice without pressing on the brake. <ACC> <ON> 12 INSTALLATION GUIDE INSTALLATION GUIDE 13

Auxiliary Harness (CN9) CN9/1 YELLOW (-250mA) AUX 1 OUTPUT This wire provides (-) 250mA programmable output whenever the transmitter button(s) controlling Aux 1 is pressed. CN9/2 YELLOW/BLACK (-250mA) AUX 2 OUTPUT This wire provides (-) 250mA programmable output whenever the transmitter button(s) controlling Aux 2 is pressed. CN9/3 VIOLET (-250mA) STARTER KILL This wire supplies a (-) 250mA ground as long as the system is armed. CN9/4 BLANK N/A CN9/5 GREY/BLACK (-250mA) AUTO LIGHT CONTROL OUTPUT Utilize this option to stop the auto light function in remote start, reservation start, and turbo start modes. Autolight control (gray/black) Door trigger pin in driver seat LF Module - Smart Door (CN10) For two switch vehicles: Please connect it with folding Switch wire as below Mount the LF module on the front windshield (if the LF module is mounted under the dash, it decreases the transmitting distance). When the Smart Remote is within the communication range (6-8 feet) of the LF module, it will unlock the vehicle. When the Smart Remote is not detected in the communication range (6-8 feet), the vehicle will lock within 12~15 seconds. 14 INSTALLATION GUIDE INSTALLATION GUIDE 15 Note The Smart Door function mode can be activated from the remote. Simply hold the unlock button for 3 seconds to activate the Smart Door mode.

Temperature Sensor (CN11): E8-B ONLY This sensor senses the interior temperature of the vehicle. Do not mount the sensor on the floor or the body of the vehicle. 2. Selection For Automatic and Manual Transmission The Jumper wire inside the cover of the main unit is used for Manual transmission vehicles. If the unit is installed on an Automatic transmission vehicle, simply cut the Jumper wire. WARNING! 3. Alternator Sensor 1. Dip Switch Do not reconnect the Jumper wire once it has been cut. It will void all warranty and it is very unsafe. 2. Noise Sensing LED The LED on the cover of the main controller unit is lit when the engine is running and the light is turned off when the engine is off. 4. Programming Noisy Sensing LED IMPORTANT! LED These steps must be completed in order for the product to operate properly. A. Remote Control Registration 1) Press the Start button (OFF ACC ON) 4 times; ON light should be displayed. (Parking light flash once, ready to program the remotes) 2) Press the I or button on the 1st remote. 3) Then press the I or button on the 2nd remote. (When the lock button is pressed on the remote, paking light flash once) 4) Remote programming is now complete. 16 INSTALLATION GUIDE INSTALLATION GUIDE 17

B. Easy Door Lock Program (Push button will not operate until Easy Door Lock is programmed) 1) Decide on a passcode, a 4 digit number. (i.e. 1234) 2) Step into the vehicle. 3) Open the driver side door. 4) Press the Start button so that it is on the Ignition ON position. 5) Step out of the vehicle. 6) Knock on the Easy Door Lock a few times until you see all the LED lights flash. 7) LED light will now move from 1 to 0. (Each number will be lit for 2 seconds) 8) Knock on the pad when the number to your passcode is lit. (Each time a number is entered, the LED light will restart from the 1 position) i.e.) On a passcode for 1234. a. Tap when the LED light is lit on the 1. b. LED light will restart from the 1 position and move onto 2. c. Tap when the LED light is lit on the 2. d. LED light will restart from the 1 position and move onto 2 and 3. e. Tap when the LED light is lit on the 3. f. LED light will restart from the 1 position and move onto 2, 3 and 4. g. Tap when the LED light is lit on the 4. 9) Once all 4 number passcodes are entered, the siren will beep once and the parking light will flash once. 10) Easy Door Lock programming is now complete. C. Smart Door Lock Registration 1) Open the driver side door. 2) Make sure the Push-to-Start button is set to the OFF position. ( START light should be lit) 3) Press the II or button for 2 seconds on the 1st remote. (Siren will beep twice) 4) Press the II or button for 2 seconds on the 2nd remote. (Siren will beep twice) 5) Smart Door programming is now complete. 5. Remote/Push Button Start Diagnostics When the remote start function is activated and the vehicle emits an error tone (3 chirps); you have the ability to see what the cause of the no-start situation is by counting the amount of flashes of the parking lights from the vehicle. Number of parking lights flashes Cause of Error 1 Engine is on 2 Ignition is to the ON position Door is open (Door wire is active) or Knock Sensor is not 3 programmed 4 Trunk is open (Trunk wire is active) 5 Brake is being pressed (Brake wire is active) 6 CN4/7 wire is not connected 7 Manual transmission mode is enabled and not initialized Parking brake / Emergency brake is off 8 Neutral safety wire has no ground or the neutral safety switch is off 18 INSTALLATION GUIDE INSTALLATION GUIDE 19

6. How to Program the Options 4) Within 3 seconds, the vehicle s parking lights will flash as well as chirp; corresponding to the first button pressed followed by chirp(s) and flashes matching the second button pressed. i.e.) Sound Select option vehicle chirps once with one flash (since the I ( ) button was pressed), followed by 4 chirps and 4 flashes (since the IV button was pressed). 5) To end programming mode, press I + IV ( + ) for 2 seconds. It will also end programming with 30 seconds of inactivity. The vehicle s parking lights will flash once and chirp once, stating that it is now out of the programming mode. B. Incorrect Programming Vehicle will chirp once to warn you that the programming was not properly programmed. Please begin the programming once again. C. Factory Setting Reset 1) Press the I + IV ( + ) button simultaneously for 2 seconds to begin the programming mode. The vehicle s parking lights will flash once and chirp once, stating that it is now in programming mode. A. To Program 1) Review the options above and remember the button sequence required for that specific option. 2) Press the I + IV ( + ) button simultaneously for 2 seconds to begin the programming mode. The vehicle s parking lights will flash once and chirp once, stating that it is now in programming mode. 3) Immediately press the two corresponding buttons (one after another). i.e.) Sound Select option press I ( ), then IV ( ). 2) Immediately press IV ( ) twice. Within 3 seconds, the vehicle s parking lights will flash as well as chirp four times, followed by four chirps and flashes. 3) To end programming mode, press I + IV ( + ) for 2 seconds. It will also end programming with 30 seconds of inactivity. The vehicle s parking lights will flash once and chirp once, stating that it is now out of the programming mode. Tech Support available on Monday thru Saturday, 9am ~ 5pm (PST) (562) 841-4968 20 INSTALLATION GUIDE INSTALLATION GUIDE 21

Select Market Trading, Inc. Limited One Year Warranty M/E/M/O This limited warranty is given to the end-user or the retail purchaser (referred to this warranty as "Original Purchaser") that it will be free from defects in material and workmanship for a period of 1 year from the date of the purchase of the new product (excluding accessory items such as harness, keypad, antenna, remote control and pager). A copy of the original proof of purchase and this warranty card with RMA number given by Select Market Trading, Inc. is required to receive warranty service. In the unlikely event that the new product should fail due to defect in material or workmanship, Select Market Trading, Inc. will repair or replace the entire product, where each party will be responsible for one-way shipping. This limited warranty does not cover any physical damage to this product, damage caused by improper installation; improper use; misuse; neglect; repair of cracked, scratched, broken or modified cosmetics; or parts that have been altered or removed; damages done by another device used with this product resulting from use of non Easycar TM - brand parts. This warranty is VOID if you purchased this product as used, floor model sample, or refurbished; if the product has been altered or modified in any way (including but not limited to attempted repair without authorization from Easycar TM - Select Market Trading, Inc. and/or alteration/removal of the serial number). This limited warranty does not cover the vehicle of any damages or liabilities in which this product is installed or being installed. This product does not guarantee avoidance of vehicle collision or accident. If you think your product is eligible for warranty service, please email to info@easycar-usa.com to receive an RMA Number with further instructions. Model Number: Serial Number: Date of Purchase: Purchased Store Name: RMA Number: Reason: U S A Name: Address: City: State: Zip: Tel: Important: An RMA (Return Material Authorization) is REQUIRED to receive warranty on defective products, along with proof of purchase and this warranty card.