D-sub J DSUMINITURE ONNETOR J SERIES Solder pot plug and receptacle SOLDER POT PLUG ND REEPTLE 01 Solder pot plug Solder pot Receptacle Features The receptacle contacts are formed by high-speed stamping presses to obtain the advantages of cold working. They are therefore highly elastic, which in turn ensures reliable connection even after many mating cycles. The dimples in the plug shell ensure continuity between it and the receptacle shell, thus providing complete shielding. Standards 0 Recognized E60381ertified LR20812 osts are kept low by selective gold plating the contacts. The solder cup portions of the contacts are tin-plated for easy soldering. Insulator housings are made of a heat-resistant glass-filled PT resin. * ontact JST if Lead-Free product is required. * Refer to "General Instruction and Notice when using Terminals and onnectors" at the end of this catalog. * ontact JST for details. Specifications Materials Model number identification onnector Part name ontact Material and Finish rass, nickel-undercoated, selective gold-plated or copper-undercoated, tin-plated J E Z P 12 Plug Insulator Glass-filled PT, UL4V-0, black Shell Steel, copper-undercoated, tin/lead-plated Series name Receptacle ontact Insulator Shell Phosphor bronze, nickel-undercoated, selective gold-plated or copper-undercoated, tin-plated Glass-filled PT, UL4V-0, black Steel, copper-undercoated, tin/lead-plated Shell size: E,,, Wire connection style: Z... Solder pot haracteristics urrent rating Voltage rating Temperature range ontact resistance Insulation resistance Withstanding voltage Note: ontact JST for details. 676 3,, D (2 for 37-circuits) 0V, D -40 to +85 (including temperature rise in applying electrical current) Initial value/mω max. fter environmental testing/30mω max. 5,000MΩ min. 1,000V /minute Number of circuits:,,, 37 onnector style: P... Plug, S... Receptacle Finish lank... Gold-plated (flash) 12... 0.2micron(8micro-inch) gold-plated 13... 0.4micron(16micro-inch) gold-plated 14... 0.76micron(30micro-inch) gold-plated 0... Tin-plated Note: 1. The relationship between number of circuits and shell size is shown below. : E, :, :, 37: 2. ontact JST for special plating requirements.
D SUMINITURE ONNETOR J SERIES Plug 10 3.05(.120)dia. 2.84(.112) 8.35(.32) 12.55(.44) [5.5(.234)] [10.72(.422)] 37 Dimensions mm(in.) Gold-plated Tin-plated JEZ- P JEZ- P-0 16.2(.666) 24.(.84) 30.80(1.213) JZ-P JZ-P-0.(.4) 33.32(1.321) 3.14(1.541) JZ-P JZ-P-0 38.7(1.534) 47.04(1.852) 53.04(2.088) JZ-37P JZ-37P-0 55.43(2.182) 63.50(2.500) 6.32(2.72) Q ty / 50 50 Receptacle 10 3.05(.120)dia. 2.84(.112) 7.(.311) 12.55(.44) 6.18 (.243) [10.(.42)] 37 Dimensions mm(in.) Gold-plated Tin-plated JEZ- S JEZ- S-0 16.34(.643) 24.(.84) 30.80(1.213) JZ-S JZ-S-0 24.67(.71) 33.33(1.312) 3.14(1.541) JZ-S JZ-S-0 38.38(1.511) 47.04(1.852) 53.04(2.088) JZ-37S JZ-37S-0 54.84(2.) 63.50(2.500) 6.32(2.72) Q ty / 50 50 677
D-sub J DSUMINITURE ONNETOR J SERIES Right angle through-hole plug and receptacle RIGT NGLE TROUG-OLE PLUG ND REEPTLE 01 Right angle through-hole plug (with hexagonal lock screw blocks) Right angle through-hole receptacle (with rectangular lock screw blocks) Right angle through-hole receptacle (with spring lock devices) Features The receptacle contacts are made by high-speed stamping presses. This promotes the uniform elasticity of the twin-contact mating sections and therefore ensures reliable contact even after repeated mating cycles. The solder tails are U-shaped for extra strength. osts are minimized by selective gold plating, high speed stamping presses, and completely automated assembly. To ensure complete shielding, a wide variety of grounding adapters are available so that the receptacles can be grounded to different kinds of supporting structures. Metric, inch or other lock screw blocks are available for fastening mating plugs. 678
D SUMINITURE ONNETOR J SERIES Specifications Materials ontact of plug Part name ontact of receptacle Insulator Shell exagonal lock screw block Rectangular lock screw block Grounding adapter having a 3.2mm(.126") dia. hole Grounding adapter having an M3 tapped hole Grounding adapter having a spring lock lever Model number identification Material and Finish rass, nickel-undercoated, selective gold-plated or copper-undercoated, tin-plated Phosphor bronze, nickel-undercoated, selective gold-plated or copper-undercoated, tin-plated Glass-filled PT, UL4V-0, black Steel, copper-undercoated, nickel-plated Steel, copper-undercoated, nickel-plated Zinc, copper-undercoated, nickel-plated Steel, copper-undercoated, nickel-plated rass, copper-undercoated, tin/lead-plated haracteristics urrent rating Voltage rating Temperature range ontact resistance Insulation resistance Withstanding voltage pplicable P board thickness Note: ontact JST for details. 3,, D (2.0, D for 37-circuits) 0V, D -40 to +85 (including temperature rise in applying electrical current) Initial value/mω max. fter environmental testing/30mω max. 5,000MΩ min. 1,000V /minute 1.6mm(.063") Standards 0 Recognized E60381 ertified LR20812 * ontact JST if Lead-Free product is required. * Refer to "General Instruction and Notice when using Terminals and onnectors" at the end of this catalog. * ontact JST for details. J E Y S 1 3 12 S1 Series name Shell size: E,,, Wire connection style: Y... Right angle through-hole style Number of circuits:,,, 37 onnector style: P... Plug, S... Receptacle onnector construction/dimensions: Standard J series Types of grounding adapters 0... Without grounding adapters 1... With grounding adapters having a 3.2mm(.126") dia. hole 2... With grounding adapters having an M3 thread 3... With grounding adapters having a spring lock device (1) 4... With grounding adapters having a spring lock device (2) Types of lock screw blocks... With hexagonal lock screw blocks having a No. 4-40 UN inch thread... With hexagonal lock screw blocks having an M2.6 thread... With rectangular lock screw blocks having an M2.6 thread D... Without lock screw blocks E... Without lock screw blocks, but with grounding adapters having a 3.05mm(.120") dia. hole F... Without lock screw blocks, but with grounding adapters having a No. 4-40UN inch thread G... Without lock screw blocks, but with grounding adapters having an M2.6 thread... Without lock screw blocks, but with grounding adapters having an M3 thread Finish lank... Gold-plated (flash) 12... 0.2micron(8micro-inch) gold-plated 13... 0.4micron(16micro-inch) gold-plated 14... 0.76micron(30micro-inch) gold-plated 0... Tin-plated Spring lock devices lank...without spring lock devices S or S1...With spring lock devices S2...With spring lock devices (with addition of spring characteristic) Note: 1. The relationship between number of circuits and shell size is shown below. : E, :, :, 37: 2. ontact JST for special plating requirements. 3. ontact JST for the Receptacle with spring lock devices. (Not UL recognized nor S certified.) 67
D SUMINITURE ONNETOR J SERIES Right angle through-hole plug Type Type 10 D 2.84 (.112) 2.84 (.112) 8.35(.32) 12.55(.44) 0.75 [5.5 (.030) (.234)] E [18.6(.732)] 3.2 (.126) : eight of the lock screw block (for Types, & ) Dimensions mm(in.) gold-plated plug tin-plated plug D JEY- P-1** JY-P-1** JY-P-1** JEY- P-1**0 JY-P-1**0 JY-P-1**0 16.0(.665) 24.(.84) 30.80(1.213).(.4) 33.33(1.312) 3.14(1.541) 38.7(1.534) 47.04(1.852) 53.00(2.087) 8.1(.31) 8.1(.31) 8.2(.323) 0.6 (.024) Q'ty / Note: ** shows the location where a two-digit code (see the table below for codes) should be entered. For example, if a -circuit gold-plated plug with hexagonal lock screw blocks having a No.4-40UN inch thread and without grounding adapters is required, specify the model number as JEY-P-10. E.52(.375).52(.375).62(.37) 60 40 With hexagonal lock screw blocks (: 6.3mm (.248")) having a No.4-40UN inch thread With hexagonal lock screw blocks (: 6.3mm (.248")) having an M2.6 thread No.4-40UN M2.6 Without grounding adapters 0 0 With grounding adapters with a 3.2mm (.126") dia. hole 1 1 With grounding adapters with an M3 thread 2 2 With grounding adapters with a spring lock device (1) 3 3 With grounding adapters with a spring lock device (2) 680
D SUMINITURE ONNETOR J SERIES Type Type D Type E Type F Type G Type With rectangular lock screw blocks (: 6.2mm (.244")) having an M2.6 thread Without lock screw blocks Without lock screw blocks E: Grounding adapter has no thread. F, G, : Grounding adapters have a thread (*1) for securing separately-purchased lock screw blocks (*2) Use a lock screw block of Model number JFS-( )S-1N. *1: No.4-40UN inch thread *2: Model number JFS-4S-( )1W(M) *1: M2.6 thread *2: Model number JFS-2.6S-( )1W(M) *1: M3 thread *2: Model number JFS-3S-( )1W(M) M2.6 3.05mm (.120")dia. hole No.4-40UN M2.6 M3 0 0D 1 1D 1E 1F 1G 2 2D 2E 2F 2G 3 3D 3E 3F 3G 4 681
D SUMINITURE ONNETOR J SERIES Right angle through-hole receptacle Type Type 10 D 2.84 (.112) 2.84 (.112) 7.(.311) 12.55(.44) 0.7 (.028) 6.18 (.243) E [18.8(.740)] 3.2 (.126) : eight of the lock screw block (for Types, & ) Dimensions mm(in.) gold-plated tin-plated receptacle receptacle D 37 JEY- S-1** JY-S-1** JY-S-1** JY-37S-1** JEY- S-1**0 JY-S-1**0 JY-S-1**0 JY-37S-1**0 16.34(.643) 24.67(.71) 38.38(1.511) 54.84(2.) 24.(.84) 30.81(1.213) 33.32(1.312) 3.14(1.541) 47.04(1.852) 53.04(2.088) 63.50(2.500) 6.32(2.72) 8.1(.31) 8.1(.31) 8.2(.323) 8.2(.323) 0.6 (.024) Q'ty / Note: ** shows the location where a two-digit code (see the table below for codes) should be entered. For example, if a -circuit gold-plated plug with hexagonal lock screw blocks having a No.4-40UN inch thread and without grounding adapters is required, specify the model number as JEY-S-10. E.52(.375).52(.375).62(.37).62(.37) 60 40 40 With hexagonal lock screw blocks (: 6.3mm (.248")) having a No.4-40UN inch thread No.4-40UN With hexagonal lock screw blocks (: 6.3mm (.248")) having an M2.6 thread M2.6 Without grounding adapters 0 0 With grounding adapters with a 3.2mm (.126") dia. hole 1 1 With grounding adapters with an M3 thread 2 2 With grounding adapters with a spring lock device (1) 3 3 With grounding adapters with a spring lock device (2) 682
D SUMINITURE ONNETOR J SERIES Type Type D Type E Type F Type G Type With rectangular lock screw blocks (: 6.2mm (.244")) having an M2.6 thread Without lock screw blocks Without lock screw blocks E: Grounding adapter has no thread. F, G, : Grounding adapters have a thread (*1) for securing separately-purchased lock screw blocks (*2) Used a lock screw block [model number JFS-( )S-1N] *1: No.4-40UN inch thread *2: Model number JFS-4S-( )1W(M) *1: M2.6 thread *2: Model number JFS-2.6S-( )1W(M) *1: M3 thread *2: Model number JFS-3S-( )1W(M) M2.6 3.05mm (.120")dia. hole No.4-40UN M2.6 M3 0 0D 1 1D 1E 1F 1G 2 2D 2E 2F 2G 3 3D 3E 3F 3G 4 683
D SUMINITURE ONNETOR J SERIES P board layout (viewed from component side) ( circuits) ( circuits) +0.1 ---1.0 0 +.004 (.03 )dia. 0 5.4 ± 0.05 2.74 ± 0.05(.216 ±.002) (.108 ±.002) 2.84 ± 0.05 (.112 ±.002) +0.1 ---1.0 0 +.004 (.03 0 )dia. 4.11 ± 0.05 (.162 ±.002) 1.37 ± 0.05 (.054 ±.002).60 ± 0.05 (.378 ±.002) 6.86 ± 0.05(.270 ±.002) 2.84 ± 0.05 (.112 ±.002) 2---3.2 ± 0.1 (.126 ±.004)dia. 1.37 ± 0.05 (.054 ±.002) 4.11 ± 0.05 (.162 ±.002) 24. ± 0.(.84 ±.006).0(.354) max. P board edge 2---3.2 ± 0.1 (.126 ±.004)dia. 2.74 ± 0.05 (.108 ±.002) 5.4 ± 0.05 (.216 ±.002) 33.32 ± 0.(1.312 ±.006) 8.23 ± 0.05(.324 ±.002).0(.354) max. P board edge ( circuits) (37 circuits) +0.1 ---1.0 0 +.004 (.03 0 )dia. 2---3.2 ± 0.1 (.126 ±.004)dia. 16.56 ± 0.05(.652 ±.002) 13.82 ± 0.05(.544 ±.002) 11.05 ± 0.05(.435 ±.002) 8.28 ± 0.05(.326 ±.002) 2.77 ± 0.05 5.54 ± 0.05(.218 ±.002) (.10 ±.002) 1.40 ± 0.05(.055 ±.002) 4.14 ± 0.05(.163 ±.002) 6.1 ± 0.05(.272 ±.002).68 ± 0.05(.381 ±.002) 12.42 ± 0.05(.48 ±.002).1 ± 0.05(.58 ±.002) 47.04 ± 0.(1.852 ±.006) 2.84 ± 0.05 (.112 ±.002).0(.354) max. P board edge +0.1 37---1.0 0 +.004 (.03 )dia. 0 2---3.2 ± 0.1 (.126 ±.004)dia. 2.77 ± 0.05 (.10 ±.002) 1.40 ± 0.05 (.055 ±.002) 4.14 ± 0.05 (.163 ±.002) 24.84 ± 0.05(.78 ±.002) 22.10 ± 0.05(.870 ±.002) 1.33 ± 0.05(.761 ±.002) 16.56 ± 0.05(.652 ±.002) 13.82 ± 0.05(.544 ±.002) 11.05 ± 0.05(.435 ±.002) 8.28 ± 0.05(.326 ±.002) 5.54 ± 0.05(.218 ±.002) 6.1 ± 0.05(.272 ±.002).68 ± 0.05(.381 ±.002) 12.42 ± 0.05(.48 ±.002).1 ± 0.05(.58 ±.002) 17.6 ± 0.05(.707 ±.002) 20.70 ± 0.05(.8 ±.002) 23.47 ± 0.05(.24 ±.002) 63.50 ± 0.(2.500 ±.006) 2.84 ± 0.05 (.112 ±.002).0(.354) max. P board edge Note: 1. Tolerances are non-cumulative: ±0.05mm (±.002") for all centers. 2. ole dimensions differ according to the kind of P board and piercing method. The dimensions above should serve as a guideline. ontact JST for details. Panel layout Mounting on the rear side Mounting on the front side 2---3.2± 0.1 (.126 ±.004)dia. 4---1.6R 10 The connector can be mounted either on the front side or on the rear side of the panel as shown above. Use M2.5 or M2.6 screws for installation. 684 37 ±0.(.006) ±0.2(.008) ±0.2(.008) 24.(1.84) 33.32(1.312) 47.04(1.852) 63.50(2.500) 20.6(1.811) 28.8(1.134) 42.6(1.677) 5.0(2.323) 12.0(.472) 12.0(.472) 12.0(.472) 12.0(.472) Note: The dimensions above should serve as a guideline. ontact JST for details.
D-sub J DSUMINITURE ONNETOR J SERIES Straight through-hole plug and receptacle STRIGT TROUG-OLE PLUG ND REEPTLE 01 Straight through-hole plug (with hexagonal lock screw blocks) Straight through-hole receptacle (without lock screw blocks, but with grounding adapters having a No.4-40UN inch thread) Features Three standard s are available with different dimensions between the flange and solder tail: 6mm (.236"), mm (.354"), and 12mm (.472"). The roots of the contact leads are covered to prevent flux from rising into the connector during soldering. 6.0 (.236) grounding adapter with a spring lock device allows the connector to be temporarily secured onto the printed circuit board so that the connector can be soldered easily. Standards 0 Recognized E6038 1ertified LR20812.0 (.354) * ontact JST if Lead-Free product is required. * Refer to "General Instruction and Notice when using Terminals and onnectors" at the end of this catalog. * ontact JST for details. 12.0 (.472) 685
D SUMINITURE ONNETOR J SERIES Specifications Materials haracteristics ontact Part name Plug Receptacle Insulator Shell eaxagonal lock screw block Grounding adapter with spring lock device Material and Finish rass, nickel-undercoated, selective gold-plated Phosphor bronze, nickel-undercoated, selective gold-plated Glass-filled PT, UL4V-0, black Steel, copper-undercoated, nickel-plated Steel, copper-undercoated, nickel-plated rass, copper-undercoated, tin/lead-plated urrent rating Voltage rating Temperature range ontact resistance Insulation resistance Withstanding voltage pplicable P board thickness *ontact JST for details. 3, D 0V, D -40 to +85 (including temperature rise in applying electrical current) Initial value/mω max. fter environmental testing/30mω max. 5,000MΩ min. 1,000V /minute 1.6mm(.063") Straight through-hole plug 10 With grounding adapters with a spring lock device 2.84(.112) 8.35(.32) : eight of the lock screw block (for Types, & J) Dimension between flange and solder tail mm(in.) 6 (.236) (.354) 12 (.472) 6 (.236) (.354) 12 (.472) Gold-plated (flash) Plug JES- P-2** JES- P-3** JES- P-4** JS-P-2** JS-P-3** JS-P-4** 12.55(.44) 3.5 2.7 3.5 2.7 D (.138)(.106) D (.138)(.106) D 0.5(.020) 5.5 6.0 3.2 (.234) (.236) (.126) [.04(.52)] Gold-plated 0.76micron(30micro-inch) JES- P-2**14 JES- P-3**14 JES- P-4**14 JS-P-2**14 JS-P-3**14 JS-P-4**14 2.84(.112) 7.6(.2) 5.5 (.234).0 (.354) [18.04(.710)] 3.2 (.126) 5.5 (.234) D 16.0 (.665) 38.7 (1.534) Dimensions mm(in.) 24. (.84) 47.04 (1.852) 30.8 (1.213) 53.0 (2.087) 3.5 (.138) 12.0 (.472) [21.04(.828)] 2.4 (.04) 2.5 (.08) Note: ** shows the location where a two-digit code (see the table below for codes) should be entered. For example, if a gold-plated (flash) receptacle with hexagonal lock screw blocks having a No. 4-40UN inch thread and without grounding adapters whose dimension between flange and solder tail is 6.0mm(.236") is required, specify the model number as JS-P-23. 2.7 (.106) Q'ty / 3.2 (.126) 6.0 mm (.236").0 mm (.354") 12.0 mm (.472") 50 With hexagonal lock screw blocks (: 6.3mm (.248")) having a No.4-40UN inch thread No.4-40UN Type 3 686
D SUMINITURE ONNETOR J SERIES Model number identification Series name Shell size:, E J S P 2 3 F 14 S1 Wire connection : S... Straight through-hole Number of circuits:, onnector : P... Plug S... Receptacle onnector construction/dimensions: 2... 6.0 mm (.236") from flange to solder tail 3....0 mm (.354") from flange to solder tail 4... 12.0mm (.472") from flange to solder tail Types of grounding adapter: 3... Grounding adapter with a spring lock device Types of lock screw block:... With hexagonal lock screw blocks having a No. 4-40UN inch thread... With hexagonal lock screw blocks having an M2.6 thread F... Without lock screw blocks, but with grounding adapters having an No.4-40UN inch thread G... Without lock screw blocks, but with grounding adapters having an M2.6 thread... Without lock screw blocks, but with grounding adapters having an M3 thread J... With hexagonal lock screw block having an M3 thread Finish lank... Gold-plated(flash) 12... 0.2micron(8micro-inch)gold-plated 13... 0.4micron(16micro-inch)gold-plated 14... 0.76micron(30micro-inch)gold-plated 0... Tin-plated Spring lock devices lank...without spring lock devices S or S1...With spring lock devices (round ) S2...With spring lock devices (with addition of spring characteristic, round ) S3...With spring lock devices (with addition of spring characteristic, rhombus ) Note: 1. In the J Series, the number of circuits is determined by the shell size: circuits for E and circuits for. 2. ontact JST for special plating requirements. 3. ontact JST for the dimensions between the flange and solder tail other than those listed above. 4. Grounding adapters that can secure printed circuit boards are also available. Type Type F Type G Type Type J With hexagonal lock screw blocks (: 6.3mm(.248")) having an M2.6 thread *1: No.4-40UN inch thread *2: Model number SFS-4S-( )1W(M) Without lock screw blocks F, G, : Grounding adapters have a thread (*1) for securing separatelypurchased lock screw blocks (*2) *1: M2.6 thread *2: Model number SFS-2.6S-( )1W(M) *1: M3 thread *2: Model number SFS-3S-( )1W(M) With hexagonal lock screw blocks (: 6.3mm (.248")) having an M3 thread M2.6 No.4-40UN M2.6 M3 M3 3 3F 3G 3 3J 687
D SUMINITURE ONNETOR J SERIES Straight through-hole receptacle 10 With grounding adapters with a spring lock device 2.84(.112) 7.(.311) 12.55(.44) D 2.7 (.106) 6.18 6.0 3.2 (.243) (.236) (.126) [.38(.606)] : eight of the lock screw block (for Types, & J) Dimension between Gold-plated (flash) Gold-plated flange and solder tail mm(in.) Tin-plated receptacle 0.76micron(30micro-inch) 6(.236) JES- S-2** JES- S-2**14 - (.354) JES- S-3** JES- S-3**14-12(.472) JES- S-4** JES- S-4**14-6(.236) JS-S-2** JS-S-2**14 JS-S-2**0 (.354) JS-S-3** JS-S-3**14 JS-S-3**0 12(.472) JS-S-4** JS-S-4**14-0.5(.020) 2.84(.112) 7.6(.2) D 2.7 (.106) 6.0 6.0 6.18 (.236) 3.2 6.18 (.236) (.243).0(.354) (.126) (.243) 12.0(.472) [18.38(.724)] [21.38(.842)] 2.7 (.106) 6.0 mm (.236").0 mm (.354") 12.0 mm (.472") Dimensions mm(in.) D 16.34 (.643) 38.38 (1.511) 24. (.84) 47.04 (1.852) 30.8 (1.213) 53.0 (2.087) D 2.4 (.04) 2.5 (.08) Note: ** shows the location where a two-digit code (see the table below for codes) should be entered. For example, if a goldplated (flash) receptacle with hexagonal lock screw blocks having a No. 4-40UN inch thread and without grounding adapters whose dimension between flange and solder tail is 6.0mm(.236") is required, specify the model number as JES-S-23. 3.2 (.126) Q'ty / 50 Type With hexagonal lock screw blocks (: 6.3mm (.248")) having a No.4-40UN inch thread No.4-40UN 3 P board layout (viewed from component side) (-circuits) (- circuits) +0.1 ---1.0 0 +.004 (.03 )dia. 0 2---3.05 ± 0.05 (.120 ±.002)dia. 5.4 ± 0.05 2.74 ± 0.05 (.216 ±.002) (.108 ±.002) 1.37 ± 0.05 (.054 ±.002) 4.11 ± 0.05 (.162 ±.002) 24. ± 0.05(.84 ±.002) 2.84 ± 0.05 (.112 ±.002) +0.1 ---1.0 0 +.004 (.03 0 )dia. 2---3.05 ± 0.05 (.120 ±.002)dia. 16.56 ± 0.05(.652 ±.002) 13.82 ± 0.05(.544 ±.002) 11.05 ± 0.05(.435 ±.002) 8.28 ± 0.05(.326 ±.002) 2.77 ± 0.05 5.54 ± 0.05(.218 ±.002) (.10 ±.002) 1.40 ± 0.05(.055 ±.002) 4.14 ± 0.05(.163 ±.002) 6.1 ± 0.05(.272 ±.002).68 ± 0.05(.381 ±.002) 12.42 ± 0.05(.48 ±.002).1 ± 0.05(.58 ±.002) 47.04 ± 0.05(1.852 ±.002) 2.84 ± 0.05 (.112 ±.002) Note: 1. Tolerances are non-cumulative: ±0.05mm (±.002") for all centers. 2. ole dimensions differ according to the kind of P board and piercing method. The dimensions above should serve as a guideline. ontact JST for details. 688
D SUMINITURE ONNETOR J SERIES Type Type F Type G Type Type J With hexagonal lock screw blocks (: 6.3mm (.248")) having an M2.6 thread *1: No.4-40UN inch thread *2: Model number SFS-4S-( )1W(M) Without lock screw blocks F, G, : Grounding adapters have a thread (*1) for securing separatelypurchased lock screw blocks (*2) *1: M2.6 thread *2: Model number SFS-2.6S-( )1W(M) *1: M3 thread *2: Model number SFS-3S-( )1W(M) With hexagonal lock screw blocks (: 6.3mm (.248")) having an M3 thread M2.6 No.4-40UN M2.6 M3 M3 3 3F 3G 3 3J Panel layout 2---3.2 ± 0.1 (.126 ±.004)dia. 4---1.6R 10 ± 0.(±.006) ± 0.2(±.008) ± 0.2(±.008) 24.(.84) 20.6(.811) 12.0(.472) 47.04(1.852) 42.6(1.677) 12.0(.472) Note: The dimensions above should serve as a guideline. ontact JST for details. 68
D-sub J DSUMINITURE ONNETOR J SERIES rimp style plug and receptacle RIMP STYLE PLUG ND REEPTLE 01 onnector Plug Receptacle 60 Part name Pin contact Insulator Shell Socket contact Insulator Shell Material and Finish rass, nickel-undercoated, selective gold-plated or copper-undercoated, tin-plated Glass-filled PT, UL4V-0, black Steel, copper-undercoated, tin/lead-plated Phosphor bronze, nickel-undercoated, selective gold-plated Glass-filled PT, UL4-0, black Steel, copper-undercoated, tin/lead-plated Pin contact The contacts of this plug are formed by high-speed stamping presses into continuous strips that can be automatically fed into our compact crimping machines. Much less time is required to assemble RT and RS-232 round cables using this plug than when soldering connections. The contacts in this connector are selectively gold-plated. Moreover, JST's advanced technological knowledge and Socket contact Features experience are fully utilized to significantly reduce production costs. The dimples in the connector shell provide the ground connection and are important factors in preventing electromagnetic interference. The contact has a lance that can be visually checked during assembly. This assures accurate assembly and reduces defects. Specifications Materials haracteristics urrent rating Voltage rating Temperature range ontact resistance Insulation resistance Withstanding voltage Note: ontact JST for details. rimp style plug 3,, D (2 for 37-circuits)(WG #20) 0V, D -40 to +85 (including temperature rise in applying electrical current) Initial value/mω max. fter environmental testing/30mω max. 5,000MΩ min. 1,000V /minute Model number identification rimp style receptacle ontact J S P 2 1 40 Series name Product shape: S... hain,... Loose piece Type of contact: P... Pin contact, S... Socket contact pplicable wire: 1... WG #24 to #20, 2... WG #28 to #24 Material: 1... rass(pin contact), 3... Phosphor bronze(socket contact) Finish 40... Gold-plated (flash) 42... 0.2micron(8micro-inch) gold-plated 43... 0.4micron(16micro-inch)gold-plated 44... 0.76micron(30micro-inch) gold-plated 0... Tin-plated Note: ontact JST for special plating requirements. ousing Series name J E P Shell size: E,,, Wire connection style:... crimp style Number of circuits:,,, 37 onnector style: P... Plug, S... Receptacle Note: The relationship between number of circuits and shell size is shown below. : E, :, :, 37: Standards 0 Recognized E6038 1ertified LR20812 * ontact JST if Lead-Free product is required. * Refer to "General Instruction and Notice when using Terminals and onnectors" at the end of this catalog. * ontact JST for details.
D SUMINITURE ONNETOR J SERIES Pin contact (for plug housing) Socket contact (for receptacle housing) 16.3(.642).3(.602) 1.0(.03) 1.(.075) 5.8(.228) 3.6(.142) 1.4(.055) 1.(.075) 4.(.167) 3.6(.142) Pin contact Socket contact Gold-plated Tin-plated Gold-plated *J-SP1140 *J-SP110 *J-SS1340 J-SP2140 J-SP210 J-SS2340 WG # #24 to #20 #28 to #24 pplicable wire lnsulation O.D. mm(in.) 1.1 to1.8mm(.043" to.071") 0. to1.3mm(.035" to.051") Q ty / reel 10,000 Note: Models marked * are not S certified. Plug housing Receptacle housing 10 3.05 (.120)dia. [10.7(.421)] 10 3.05 (.120)dia. [10.7(.421)] 2.84(.112) 8.35(.32) 12.55(.44) 7.0(.276) 2.84(.112) 7.(.311) 12.55(.44) 7.0(.276) [5.5 (.234)] [10.8(.4)] 6.18 (.243) [10.(.42)] Dimensions mm(in.) Q ty / Dimensions mm(in.) Q ty / 37 JE- P J-P J-P J-37P 16.2(.666).(.4) 38.7(1.534) 55.43(2.182) 24.(.84) 33.32(1.312) 47.04(1.852) 63.50(2.500) 30.80(1.213) 3.14(1.541) 53.04(2.088) 6.32(2.72) 50 50 JE- S J-S J-S 16.34(.643) 24.67(.71) 38.38(1.511) 24.(.84) 33.33(1.312) 47.04(1.852) 30.80(1.213) 3.14(1.541) 53.04(2.088) 50 pplicator for the semi-automatic press P-K2N ontact rimp applicator MKS-L ompact crimp applicator MKS-LS Strip-crimp applicator MKS-S with safety cover without safety cover with safety cover without safety cover with safety cover J-SP1*** PLMK J-SP/SS1 PLN J-SP/SS1 PLS J-SP/SS1 J-SS1*** PLMK J-SP/SS1 PLN J-SP/SS1 PLS J-SP/SS1 J-SP2*** PLMK J-SP/SS2 PLN J-SP/SS2 PLS J-SP/SS2 J-SS2*** PLMK J-SP/SS2 PLN J-SP/SS2 PLS J-SP/SS2 61
ccessories DONNETOR EMI prevention shielding cover ( J cover) SUMINITURE J&JK SERIES J OVER J cover over over nut Features This shielding cover is made of steel, formed by our advanced stamping technology, and nickel-plated. The -shaped cover completely encloses such EMI radiating areas as the connections between the connector and wires. The result is a superior shielding effect. To install the shielding cover, simply align and press the upper and lower cover elements, then tighten the nuts. It then securely grips the round cables. This cover is so compact, light and sturdy, that it can be used to cover the connectors of any input/output cable. Moreover, it is attractive in appearance. * ontact JST if Lead-Free product is required. * Refer to "General Instruction and Notice when using Terminals and onnectors" at the end of this catalog. * ontact JST for details. pplicable cable dimensions J series 37 JK series able outer diameter mm(in.) 7.0 ±0.2(.276±.008) 8.0 ±0.2(.3±.008) 10.0 ±0.2(.34±.008) Shielding cover Shielding cover 6.0 (.236) 10.0 (.34) W 16.4(.646) L 10.0 (.34) W 3.0 (.118) dia. 16.6(.654) L J series JK series Dimensions mm(in.) W L Q'ty / J series JK series J-S Dimensions mm(in.) W L 30.0(1.181) [42.0(1.654)] Q'ty / 200 37 J-S J-S J-S J-S37 JK-S 1.4(.764) 27.6(1.087) 41.4(1.630) 57.8(2.276) 42.0(1.654) 46.(1.846) 57.0(2.244) 70.6(2.780) 200 0 1 37 J-S 38.0(1.46) J-S 52.0(2.047) J-S37 68.0(2.677) Material and Finish [4.7(1.57)] [57.0(2.244)] [70.6(2.780)] 0 0 Material and Finish Steel, copper- undercoated, nickel-plated Note: The cover of the JK series -circuit connector is the same as that of the J series -circuit connector, except for the number of circuits indicated. Steel, copper-undercoated, nickel-plated Note: The cover of the JK series -circuit connector is the same as that of the J series -circuit connector. 7
D SUMINITURE ONNETOR J&JK SERIES over nut E-ring D d L 5.0 (.17) dia. Thickness 0.4 (.016) 16.4(.646) D d L J-N. 13.6(.535) 7.2(.283) 1.0(.748) Q'ty / 1,000 J-ER Material Q'ty / 5,000 J-N 16.4(.646) 8.4(.331).0(.84) 1,000 Stainless steel 37 J-N37 18.8(.740) 10.4(.40) Material Glass-filled, PT, UL4V-0, black 28.0(1.102) 1,500 Note: The cover nuts, lock screws and E-rings are used with both the J and JK series connectors. Lock screw No.4-40UN (Inch thread) M2.6 (Metric thread) M3 (Metric thread) No.4-40UN M2.6 M3 4.5(.177) 1.7(.067) 5.7(.224) 2.7(.106) 4.5(.177) 1.7(.067) 5.7(.224) 2.7(.106) 4.5(.177) 1.7(.067) 5.7(.224) 2.7(.106) Type of screw No.4-40UN (Inch thread) M2.6 (Metric thread) M3 (Metric thread) J-SL-1 J-SL-2 J-SL-3 Q'ty / 5,000 5,000 5,000 Material and Finish Steel, copper-undercoated, nickel-plated Use the following Model Nos. when ordering J-covers as a set. J series JK series Parts in one set Q'ty / 37 J- -( ) J--( ) J--( ) J-37-( ) JK--( ) Shielding cover Shielding cover over nut Lock screw E-ring Note: In the above lock screw model numbers, the number in parentheses indicates the of screw-1: Inch thread (No.4-40UN), 2: Metric thread (M2.6), 3: Metric thread (M3). 1 pc. 1 pc. 1 pc. 2 pcs. 1 set 20 10 716
D SUMINITURE ONNETOR J&JK SERIES J-cover assembly procedure J series JK series Shielding cover 5 Shielding cover Lock screw E-ring 6 4 Lock screw 7 E-ring onnector 1 Wire 2 over nut opper foil tape ontact over nut Meshed wire rimp style plug opper foil tape Shielding cover Meshed wire Wire 3 Shielding cover Lance Lance 14.0 (.551) 14.0 (.551) ssembly procedure 1. onnect wires to the connector by soldering or crimping. 2. Fold back the braided shielding wire along the outside insulation and wind the copper foil tape around the shielding wire. 3. Install the connector into shielding cover. 4. Screw the lock screws onto shielding cover. 5. Install the E-rings. 6. lign shielding cover with shielding cover and press shielding cover until it engages the lances of shielding cover. 7. Tighten the cover nut until the predetermined position is reached. Note: For details of the J-cover assembly procedure, please refer to the processing specifications separately available. The shielding effect of the J-cover is critically dependent on proper assembly. Dimensions after assembly Dimensions mm(in.) J series JK series 37 24.(.84) 33.32(1.312) 47.04(1.852) 63.50(2.500) [4.0(1.2)] [53.0(2.087)] [64.5(2.53)] [78.5(3.01)] 13.6(.535) 13.6(.535) 16.4(.646) 18.(.744) 717
ccessories DONNETOR EMI prevention overmolding cover SUMINITURE J&JK SERIES MOLD OVER Features This cover completely encloses all wire connections to the connector, and its braided wire crimp section ensures a reliable ground connection. The result is excellent shielding. This cover is sturdy enough to withstand the high pressure necessary during overmolding. It can thus be finish-molded directly. * ontact JST if Lead-Free product is required. * Refer to "General Instruction and Notice when using Terminals and onnectors" at the end of this catalog. * ontact JST for details. pplicable cable diameter J series JK series able O.D.mm(in.) 8.6±0.2(.33±.008) 7.6±0.2(.2±.008) 8.6±0.2(.33±.008) Note: ontact JST for cables other than those listed above. Ferrule L T J series JK series, Ferrule Dimensions mm(in.) D dia. T L 8.0(.3) 0.5(.020) 4.0(.7) 11.3(.445) 0.6(.024) 8.0(.3) D dia. 7.0(.276) 10.5(.413) 0.5(.020) 0.6(.024) 4.0(.7) 8.0(.3) Mold cover Mold cover JK-M-3 J-M J-M-4 JK-M-3 J-M J-M-4 16.2(.638) [J-M:24.4(.61)] 18.0(.70) 38.0(1.46) 17.4(.685) [.6(1.008)] 18.0(.70) 3.2(1.543) 18.0(.70) 18.0(.70) 37.0(1.457)[37.6(1.480)] 3.0(1.535) 37.0(1.457)[37.6(1.480)] 3.0(1.535) 2.7 (.106) 2.7 (.106) 2.7 (.106) 2.7 (.106) 7.8 (.307) 7.8 (.307) 7.4 (.21) 7.4 (.21) *Dimensions in [ the J-M. 718 ]are those for *Dimensions in [ the J-M. ]are those for
D SUMINITURE ONNETOR J&JK SERIES Mold cover assembly procedure Mold cover Ferrule ontact rimp style plug Ferrule opper foil tape raided wire Mold cover Mold Thumb screw Mold cover assembly <Molded assembly> Note: ontact JST for thumb screws. ssembly procedure 1. Processing braided shielding wire Pass the cable through ferrule and remove the insulation at the end of the cable. Install ferrule and fold back the braided shielding wire along the outside insulation. Then wind the copper foil tape around the shielding wire. 3. ssembling the mold covers lign mold cover with mold cover and press mold cover until it engages the lances of mold cover. Install ferrule over the cable holding section of the cover assembly and crimp ferrule. This completes the assembly. 2. onnecting the wires to the contacts onnect the wires to the contacts by crimping and insert the contacts into the housing. J series JK series Parts name Material and Finish Q'ty / or bag Mold cover Mold cover Ferrule Ferrule JK-M-3 JK-M-3 JK-FL-8.0 JK-FL-11.3 Steel, copper-undercoated, nickel-plated opper, tin-plated 500 0 500 Mold cover Mold cover Ferrule Ferrule J-M J-M J-FL-7.0 J-FL-10.5 Steel, copper-undercoated, nickel-plated opper, tin-plated 200 0 500 Mold cover Mold cover Ferrule Ferrule J-M-4 J-M-4 JK-FL-8.0 JK-FL-11.3 Steel, copper-undercoated, nickel-plated opper, tin-plated 0 0 500 pplicator for the semi-automatic press P-K2N ontact rimp applicator MKS-RG with safety cover without safety cover JK-FL-11.3 PLMK JK-M PLN JK-M J-FL-10.5 PLMK J-M PLN J-M 71
ccessories Dovers SUMINITURE J&JK ONNETOR SERIES EMI SIELDING LUMINUM DIE-ST OVER (for -circuit J series connectors) 1.0(.748) 45.0(1.772) 40.0(1.575) 55.0(2.165) 4.0(.7) M2.6 x 0.45(.018) 14.0 (.551) 20.0(.787) Features Parts in one set This cover is made of aluminum die-cast. The D subminiature connector and all its wire connections can be completely covered to provide excellent shielding. This EMI shielding cover can be used together with the hexagonal and rectangular metric lock screws specified in JIS-6361. This cover is ideally suited for RS-232 cable connectors. J-EM over - 1 pc. over - 1 pc. Lock screw - 2 pcs. able clamp - 2 pcs. over screws and nuts - 2 pcs. for each lamp screws - 4 pcs. over material luminum die-cast * ontact JST if Lead-Free product is required. * Refer to "General Instruction and Notice when using Terminals and onnectors" at the end of this catalog. * ontact JST for details. Q ty / 10 JIS STYLE PLSTI OVER (for -circuit J series connectors) 1.0(.748) 45.0(1.772) 40.0(1.575) 55.0(2.165) 4.0(.7) M2.6 x 0.45(.018) 14.0 (.551) 20.0(.787) Features Parts in one set Molded plastic cover. This cover can be used together with the hexagonal and rectangular metric lock screws specified in JIS--6361. * ontact JST if Lead-Free product is required. * Refer to "General Instruction and Notice when using Terminals and onnectors" at the end of this catalog. * ontact JST for details. 720 over material Q ty / J-M overs - 2 pcs. Lock screw - 2 pcs. able clamp - 2 pcs. over screws and nuts - 2 pcs. for each lamp screws - 2 pcs. S resin 10
ccessories D SUMINITURE ONNETOR Lock screw block J J JK & K SERIES varietly of accessories are available for the D subminiature connectors. LOK SREW LOK exagonal lock screw block (inch thread: No.4-40UN) 4.78(.188) L L No.4-40UN No.4-40UN No.4-40UN Type Type pplicable series Dimension / Dimension L mm(in.) J series right angle throughhole JK series straight throughhole JK series right angle throughhole J series straight throughhole J series right angle throughhole K series right angle throughhole 13.1(.516).0(.51) 10.0(.34) 11.8(.465) JFS-4S-1N JFS-4S-1W JFS-4S-1W JFS-4S-1WM JFS-4S-1WM KFS-4S-1N KFS-4S-1W KFS-4S-1W KFS-4S-1WM KFS-4S-1WM SFS-4S-1W SFS-4S-1W SFS-4S-1WM SFS-4S-1WM Dimension mm(in.) 5.5(.217) FS-4S-1W FS-4S-1W FS-4S-1WM FS-4S-1WM 4.8(.18) 5.5(.217) 4.8(.18) 5.5(.217) Type ttachment Q'ty / Spring washer.. 1 pc. Nut... 1 pc. Spring washer.. 1 pc. exagonal lock screw & spring washer are integrated 2,000 exagonal lock screw block (metric thread: M3) 4.78(.188) L L M3 M3 Type M3 Type pplicable series Dimension / Dimension L mm(in.) J series right angle throughhole JK series straight throughhole JK series right angle throughhole J series straight throughhole J series right angle throughhole K series right angle throughhole 13.1(.516).0(.51) 10.0(.34) 11.8(.465) JFS-3S-1N JFS-3S-1W JFS-3S-1W JFS-3S-1WM JFS-3S-1WM KFS-3S-1N KFS-3S-1W KFS-3S-1W KFS-3S-1WM KFS-3S-1WM SFS-3S-1W SFS-3S-1W SFS-3S-1WM SFS-3S-1WM Dimension mm(in.) 5.5(.217) FS-3S-1W FS-3S-1W FS-3S-1WM FS-3S-1WM 4.8(.18) 5.5(.217) 4.8(.18) 5.5(.217) Type ttachment Q'ty / Spring washer.. 1 pc. Nut... 1 pc. Spring washer.. 1 pc. exagonal lock screw & spring washer are integrated 2,000 721
D SUMINITURE ONNETOR J J JK & K SERIES exagonal lock screw block (metric thread: M2.6) 4.78(.188) L L M2.6 M2.6 M2.6 Type Type pplicable series Dimension / Dimension L mm(in.) J series right angle throughhole JK series straight throughhole JFS-2.6S-1N JK series right angle throughhole KFS-2.6S-1N J series straight throughhole J series right angle throughhole K series right angle throughhole 13.1(.516).0(.51) 10.0(.34) 11.8(.465) JFS-2.6S-1W JFS-2.6S-1W KFS-2.6S-1W KFS-2.6S-1W SFS-2.6S-1W SFS-2.6S-1W FS-2.6S-1W FS-2.6S-1W JFS-2.6S-1WM KFS-2.6S-1WM SFS-2.6S-1WM FS-2.6S-1WM JFS-2.6S-1WM KFS-2.6S-1WM SFS-2.6S-1WM FS-2.6S-1WM Dimension mm(in.) 5.5(.217) 4.8(.18) 5.5(.217) 4.8(.18) 5.5(.217) Type ttachment Q ty / Spring washer.. 1 pc. Nut... 1 pc. Spring washer.. 1 pc. exagonal lock screw & spring washer are integrated 2,000 Rectangular lock screw block (metric thread: M2.6) 1.2(.047) 12.6(.46) M2.6 6.2(.244) 1.0(.03) 6.1(.240) 1.0(.03) JFS-2.6R-N ttachment Spring washer 1 pc. Set screw 1 pc. Q ty / 1,000 722
D SUMINITURE ONNETOR J J JK & K SERIES pplication examples of hexagonal lock screw blocks Total dimension 6.2(.244) onnector flange Grounding adapter with threads The resulting total dimension from the connector flange to the top of the hexagonal lock screw block must be 6.2mm(.244") after assembly. The D subminiature connector can be installed on the Panel by simply tightening the hexagonal lock screw block together with grounding adapter, which has an identical thread to that of the F, G, and s. eight of lock screw block 4.8(.18) P board Panel 0.8 thickness (.031) Spring washer thickness 0.6(.024) DUST OVER (for receptacles) Type 18.0(.70) 6.6(.260) Type J series JK series J-DES J-DES-1 Q ty / 1,000.6(.378) J DES JST Material Nylon, UL4V-0, black Type 18.0(.70) 3.0(.118)dia. 7.4(.21).6(.378) J DES-1 JST.0(.84) 33.0(1.2) EXTRTION TOOL With this tool, contacts (connected to wires by crimping) can be easily removed if they are improperly inserted into plug and receptacle housings. pplicable onnector J series Plug JK series Receptacle DEJ-0.3 KEJ-0.7 KEJ-0.4 723