RKE CONTROL VEHICLE STILITY CONTROL SYSTEM 65 DTC C0210/33 Rear Speed Sensor RH Circuit DTC C0215/34 Rear Speed Sensor LH Circuit DTC C1238/38 DTC C1239/39 Foreign Object is ttached on Tip of Rear Speed Sensor RH Foreign Object is ttached on Tip of Rear Speed Sensor LH DESCRIPTION The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the S,, TRC, -TRC, VSC, UTO LSD, downhill assist and hill-start assist control systems. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing. To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the ECU. Speed Sensor MRE MRE Sensor IC (+) To ECU (-) Speed Sensor Rotor (earing Inner Race) Low speed High speed 2.6 V 1.4 V 0.7 V ackward Forward I042838E01
66 RKE CONTROL VEHICLE STILITY CONTROL SYSTEM DTC No. DTC Detection Condition Trouble rea C0210/33 C0215/34 C1238/38 C1239/39 When any of the following conditions is detected: 1. t a vehicle speed of 6 mph (10 km/h) or more, pulses are not input for 1 second. 2. Momentary interruption of the speed sensor signal occurs at least 255 times when switching the ignition switch ON and OFF. 3. Continuous noise occurs in speed sensor signals at a vehicle speed of 12 mph (20 km/h) or more. 4. Speed sensor signal circuit is open for 0.12 seconds or more. 5. 3 of the wheel sensors detect normal reversing signals, and the other wheel sensor detects malfunction signals 75 times with IG ON while reversing at 3 km/h. 6. Rotating direction of each wheel changes 7 times within 0.006 seconds with IG ON while driving at 10 km/ h or more. 7. Rotating direction of one of the wheels is not the same as that of the other wheels for 1 second while driving at 30 km/h or more. 8. Reversing signal is output for 1 second or more while driving at 100 km/h or more. 9. Rotating direction of one of the wheels is not detected normally, and the rotating direction of each of the other wheels is not the same for 1 second while driving at 30 km/h or more. Continuous noise occurs in speed sensor signals when vehicle speed is 12 mph (20 km/h) or more for 5 seconds or more. HINT: DTC C0210/33 and C1238/38 are for the right rear speed sensor. DTC C0215/34 and C1239/39 are for the left rear speed sensor. Right rear and left rear speed sensor Each speed sensor circuit Speed sensor rotor Sensor installation Master cylinder solenoid Right rear and left rear speed sensor Speed sensor rotor Sensor installation Master cylinder solenoid
RKE CONTROL VEHICLE STILITY CONTROL SYSTEM 67 WIRI DIGRM Rear Speed Sensor RH 1 2 Shielded Master Cylinder Solenoid 5 S28 RR+ 19 S28 RR- Rear Speed Sensor LH 1 2 Shielded 20 S28 6 S28 RL+ RL- C132911E01 INSPECTION PROCEDURE When replacing the master cylinder solenoid, perform zero point calibration (See page -20). 1 RED VLUE OF INTELLIGENT TESTER (MOMENTRY INTERRUPTION OF RER SPEED SENSOR) (c) Connect the intelligent tester to the DLC3. Turn the ignition switch to the ON position and push the intelligent tester main switch ON. Select "DT LIST" mode on the intelligent tester. Item Measurement Item / Range (Display) Normal Condition Diagnostic Note SPD SEN RR Speed sensor open detection (RR)/OPN DET or NORML OPN DET: Momentary interruption NORML: Normal - SPD SEN RL Speed sensor open detection (RL)/OPN DET or NORML OPN DET: Momentary interruption NORML: Normal - (d) Check for any momentary interruption in the wire harness and connector corresponding to a DTC (See page -18). : There are no momentary interruptions.
68 RKE CONTROL VEHICLE STILITY CONTROL SYSTEM HINT: Perform the above inspection before removing the sensor and connector. REPIR OR REPLCE HRNESS OR CONNECTOR (SPEED SENSOR CIRCUIT) 2 RED VLUE OF INTELLIGENT TESTER (RER SPEED SENSOR) Item Measurement Item / Range (Display) Normal Condition Diagnostic Note WHEEL SPD RR Wheel speed sensor (RR) reading /Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h) ctual wheel speed Similar speed as indicated on speedometer WHEEL SPD RL Wheel speed sensor (RL) reading /Min.: 0 mph (0 km/h), Max.: 202 mph (326 km/h) ctual wheel speed Similar speed as indicated on speedometer Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle. : The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed. Go to step 4 3 PERFORM TEST MODE (SIGNL CHECK) Result Condition Test mode (signal check) DTC is output Test mode (signal check) DTC is not output Check if test mode (signal check) DTCs are detected. Proceed to Go to step 10
RKE CONTROL VEHICLE STILITY CONTROL SYSTEM 69 4 INSPECT RER SPEED SENSOR INSTLLTION 8.3 N*m (85 kgf*cm, 73 in.*lbf) No clearance Check the speed sensor installation. : The installation nut is tightened properly. There is no clearance between the sensor and the rear axle. Torque: 8.3 N*m (85 kgf*cm, 73 in.*lbf) Check the speed sensor signal after replacement (See page -23). I044006E04 INSTLL RER SPEED SENSOR CORRECTLY 5 INSPECT SPEED SENSOR TIP Remove the rear speed sensor (See page -213). Check the sensor tip. : No scratches or foreign matter on the sensor tip. Check the speed sensor signal after cleaning/ replacement (See page -23). CLEN OR REPLCE RER SPEED SENSOR 6 INSPECT RER SPEED SENSOR Rear Speed Sensor: 2 41 :RH 40 :LH 1 (c) (d) Install the rear speed sensor. Turn the ignition switch off. Disconnect the rear speed sensor connector. Measure the resistance according to the value(s) in the table below. Standard resistance: RH I045651E03 41-2 (RR+) - ody ground 41-1 (RR-) - ody ground LH 40-2 (RL+) - ody ground 40-1 (RL-) - ody ground REPLCE RER SPEED SENSOR
70 RKE CONTROL VEHICLE STILITY CONTROL SYSTEM 7 INSPECT SKID CONTROL SENSOR WIRE Skid Control Sensor Wire: Sensor Side Connector : 41 40 :RH :LH Vehicle Side Connector : I044004E05 Disconnect the skid control sensor wire. Measure the resistance according to the value(s) in the table below. Standard resistance: RH 41 (""-2) - 41 (""-4) 41 (""-2) - 41 (""-3) 41 (""-2) - ody ground 41 (""-1) - 41 (""-3) 41 (""-1) - 41 (""-4) 41 (""-1) - ody ground LH elow 1 Ω elow 1 Ω 40 (""-2) - 40 (""-2) 40 (""-2) - 40 (""-1) 40 (""-2) - ody ground 40 (""-1) - 40 (""-1) 40 (""-1) - 40 (""-2) 40 (""-1) - ody ground elow 1 Ω elow 1 Ω Check the speed sensor signal after replacement (See page -23). REPLCE SKID CONTROL SENSOR WIRE
RKE CONTROL VEHICLE STILITY CONTROL SYSTEM 71 8 CHECK HRNESS ND CONNECTOR (SKID CONTROL ECU - RER SPEED SENSOR) Skid Control ECU (harness side connector front view) S28 RR+ RL- Disconnect the skid control ECU connector. Measure the resistance according to the value(s) in the table below. Standard resistance: RH RR- RL+ S28-5 (RR+) - 41 (-4) (RR+) elow 1 Ω S28-5 (RR+) - ody ground S28-19 (RR-) - 41 (-3) (RR-) elow 1 Ω S28-19 (RR-) - ody ground Rear Speed Sensor (harness side connector front view) 40 :LH 41 :RH LH S28-20 (RL+) - 40 (-2) (RL+) elow 1 Ω S28-20 (RL+) - ody ground S28-6 (RL-) - 40 (-1) (RL-) elow 1 Ω S28-6 (RL-) - ody ground RL- RL+ RR- RR+ F049552E18 REPIR OR REPLCE HRNESS OR CONNECTOR 9 INSPECT MSTER CYLINDER SOLENOID Rear Speed Sensor (harness side connector front view) 40 :LH 41 :RH (c) Reconnect the skid control ECU connector. Turn the ignition switch to the ON position. Measure the voltage according to the value(s) in the table below. Standard voltage: RH RL+ RR+ C110680E19 41 (-4) (RR+) - ody ground LH 7.5 to 12 V 40 (-2) (RL+) - ody ground 7.5 to 12 V REPLCE MSTER CYLINDER SOLENOID 10 RECONFIRM DTC Clear the DTCs (See page -39). Drive the vehicle at a speed of approximately 20 mph (32 km/h) or more for 60 seconds or more.
72 RKE CONTROL VEHICLE STILITY CONTROL SYSTEM Result (c) Check if the same pending DTCs are detected (See page -39). HINT: Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs. Condition DTC is output DTC is not output (When troubleshooting in accordance with the DTC CHRT.) DTC is not output (When troubleshooting in accordance with the PROLEM SYMPTOMS TLE.) Proceed to C C END PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROLEM SYMPTOMS TLE 11 REPLCE RER SPEED SENSOR NEXT Replace the rear speed sensor (See page -213). Check the speed sensor signal after replacement (See page -23). 12 RECONFIRM DTC Result DTC is output DTC is not output Condition Clear the DTCs (See page -39). Drive the vehicle at a speed of approximately 20 mph (32 km/h) or more for 60 seconds or more. (c) Check if the same pending DTCs are detected (See page -39). HINT: Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs. Proceed to END 13 INSPECT SPEED SENSOR ROTOR Remove the rear axle bearing assembly (See page H- 23).
RKE CONTROL VEHICLE STILITY CONTROL SYSTEM 73 Check the sensor rotor. : No scratches, oil, or foreign matter on the rotors. Check the speed sensor signal after cleaning/ replacement (See page -23). CLEN OR REPLCE RER XLE ERI SSEMLY (SPEED SENSOR ROTOR) REPLCE MSTER CYLINDER SOLENOID