Owner's Manual Model: LG-00-0 (00) ( Gallon Lawn & Garden Trailer er) Technical Specifications Gal. Corrosion-Resistant Polyethylene Tank Volt Diaphragm Pump,. g.p.m. - 0 p.s.i. Deluxe Pistol-Grip Handgun Ft. Handgun Hose Ft. max. vertical throw, Ft. max. horizontal throw Low Profile Trailer & Tank.0 x.0 x Pneumatic Tires Gauge Adjustable -Nozzle Boom Assembly, 0" Coverage Assembly Instructions Your sprayer has been partially assembled at the factory. Follow the instructions below to complete the assembly of this unit. (Refer to the exploded view drawing later in this manual). Bolt the hitch brackets, both formed and flat, to the trailer frame.. Slide the axle through the frame holes, centering it as best as possible.. Slide a wheel spacer and a wheel (valve stem out) onto each end of the axle, then use a cotter pin to secure the wheels in place.. Bolt the boom brackets to the back of the frame.. Bolt the boom assembly to the boom brackets with the tips of the boom facing rearward. The tips need to be approximately " above the spraying surface. Secure in place with () bolts and nuts provided.. Thread the pressure gauge into the end of the manifold assembly. Use a good grade of thread sealant, to insure no leaks. 7. Remove the drain plug, handgun clips, and attach them to the tank, as shown.. Attach the 'loose' boom feeder hose to the center hose barb on the manifold assembly and to the nylon feeder "tee" on the boom. Secure in place with /" hose clamps.. Connect the electrical hook-up to the end of your pump and clip the clips to a fully charged battery. The red wire must be connected to the positive (+), and the black wire should be connected to the negative (-). General Information Thank you for purchasing this product. The purpose of this manual is to assist you in operating and maintaining your lawn & garden trailer sprayer. Please read it carefully, as it furnishes information which will help you achieve years of trouble-free operation. *** IMPORTANT REMINDER *** Detail A Warranty/Parts/Service Products are warranted for one year from date of purchase against manufacturer or workmanship defects. Commercial users have a 0 day warranty. Your authorized dealer is the best source of replacement parts and service. To obtain prompt, efficient service, always remember to give the following information... - Correct Part Description and/or part number. - Model number/serial number of your sprayer. A Inlet from Tank This sprayer comes with an On/Off (shut-off) valve located at the inlet location of the tank, towards the underside. (See Detail A). You must make sure the valve is in the "open" position before using your sprayer. Filter/Screen "ON/OFF" Valve Part descriptions and part numbers can be obtained from the illustrated parts list section(s) of this manual. Whenever you need parts or repair service, contact your distributor/dealer first. For warranty work, always take your original sales slip, or other evidence of purchase date, to your distributor/dealer. www.fimcoindustries.com 000 FIMCO Lane, P.O. Box 700, North Sioux City, SD 70 Toll Free Phone: 00--007 : Toll Free Fax: 00--00 Form [00 (0/)] Printed in the U.S.A.
Testing the er NOTE: It is VERY important for you to test your sprayer with plain water before actual spraying is attempted. This will enable you to check the sprayer for leaks, without the possibility of losing any expensive chemicals. Add water to the tank & drive to the starting place for spraying. When you are ready to spray, turn the boom valve to the "on" position. This will start solution spraying from the tips of the boom. The pressure will decrease slightly when the boom is spraying. Adjust the pressure by turning the "ON/OFF" valve lever on the bypass line valve. Read the operating instructions and Initially begin spraying by closing the 'bypass' valve (this is the center ON/OFF valve located at the center port of your manifold assembly) and opening the boom line valve (this is the 'other' valve on the manifold). This will enable the air in the line to be eliminated (purged) through all the tips, while building pressure. When everything tests all right (no leaks, & good pressure), add the desired chemicals to the mixture and water combination and start your spraying operation. Adjust the pressure and spray as you did in the testing procedure. Conditions of weather and terrain must be considered when setting the sprayer. Do not spray on windy days. Protective clothing must be worn in some cases. Be sure to read the chemical label(s) correctly! WARNING: Some chemicals will damage the pump valves if allowed to soak untreated for a length of time. ALWAYS thoroughly flush the pump with water after use. DO NOT allow chemicals to sit in the pump for extended times of idleness. Follow the chemical manufacturer's instructions on disposal of all waste water from the sprayer. Operation Your sprayer is equipped with () ON/OFF switches. One is on the wire assembly that you hook up to your battery, the other is on the pump itself, on the opposite end of the pressure switch. The "-" is the "ON" position and the "o" is the "OFF" position for the switches. Make sure both switches are depressed in the "-" position for operation. In addition to the ON/OFF switch, the pump is equipped with an electronic pressure switch that is factory pre-set for it to shut off at 0 p.s.i.. This switch assembly is the 'square box' on the head portion of the pump. Always fill the tank with a desired amount of water first, and then add the chemical slowly, mixing as you pour the chemical into the tank. You may use the handgun to spray into the solution in order to mix the chemical and water. The pumping system draws solution from the tank, through the strainer/filter, and to the pump. The pump forces the solution under pressure to the handgun and/or boom nozzles. Open the handgun by squeezing the handle lever. Rotating the adjustable nozzle tip on the handgun will change the tip pattern from a straight stream to a cone pattern (finer mist). (Color) Speed Chart Time Required in seconds to travel a distance of: Speed in M.P.H. (Miles per Hour) 00 Ft. 00 Ft. 00 Ft..0.0 sec. sec. 0 sec. 0.0.0 7.0 7.0 7.0.7.0.0 0.0. 7.. 7 0 " " " 0 0 0 0 0 0 0 0 0 0 0 0.0...0...0.. Chart Gallons Per Acre - Based on Water 7.. 7 0 Gallons Per 000 Sq. Ft. - Based on Water.0.0..7.7.7.0.00.... Gallons Per 00 Sq. Ft. - Based on Water.0.0.0.0.0.0.0..07.0.0.0.0.0.7.07.0.0.0.0.07.0.0.0.0.0.07.0 Calibration. 0...7.... 0 7. 7. 0....0.0...0.... 0. 7.7......7 7. Chemical labels may show application rates in gallons per acre, gallons per 000 square feet, or gallons per 00 square feet. You will note that the tip chart shows all of these rating systems. Once you know how much you are going to spray, then determine (from the tip chart) the spraying pressure (PSI), and the spraying speed (). Determining the proper speed of the pulling vehicle can be done by marking off 00, 00, & 00 feet. The speed chart indicates the number of seconds it takes to travel the distances. Set the throttle and with a running start, travel the distances. Adjust the throttle until you travel the distances in the number of seconds indicated by the speed chart. Once you have reached the throttle setting needed, mark the throttle location so you can stop and go again, returning to the same speed. Add water and proper amount of chemical to the tank and drive to the starting place for spraying. 0.0..7.0 0 This sprayer is designed to be towed behind a garden tractor. The nozzles on the boom will spray an 0 inch wide swath. Check the nozzle pattern by spraying water on a concrete surface. Raise the boom to a higher mounting position to get more spray pattern overlap, if desired. Page
Pump Model: 770 Available Replacement Parts 7 0 Item No Part Number Qty Description 70 7. Amp 'Mini Blade' Fuse Port Kit Fitting, /" MNPT Port Kit Fitting, /" Hose Barb 7 Port Kit Fitting, /" Hose Barb Upper Housing Assembly Plunger Kit 7 70 Switch Assembly 00-000 0 Pkg. () Clips (Port Fitting) Check Valve Kit (w/o-ring) 0 00 Diaphragm/Piston/Cam/Bearing Kit Mounting Feet (Pkg of ) 707 On/Off Rocker Switch w/cover Troubleshooting the Pump: Motor does not run: Check for loose wiring connection(s). Make sure the 'ON/OFF' switches in both the lead wire assembly & on the pump motor are in the 'ON' position. "I" is the 'ON' position and 'O' is the 'OFF' position. Check for defective pressure switch. Make sure you are connected to a good volt power source. Make sure your on/off switches are in the 'on' position. Remove the cap to the pressure switch. Pull both red wires off of their terminals, and touch the two ends together. If your pump runs when you do this, your pressure switch will need to be replaced. Check the fuse. Check for low voltage at the power supply. Pump Specifications Pump does not prime: Flow Rate:. GPM @ Open Flow Check for air leaks in supply line. Current:. Amps @ 0 PSI Check for debris in the check valve assembly. Check for defective check valve. Check Valve: Viton Check for clogged strainer/filter. Port Type: Plug-In Port Check for cracks in the pump housing. Motor Voltage: Volts DC Check for empty product supply. Pulsating flow (surging): Check for defective pressure switch. Check for leaks in the discharge line. Check for restriction in the discharge line. Check for debris in nozzle orifice. Discharge hose may be too long. Check for clogged strainer. Motor continues to run after discharge is shut off: Check for empty product supply. Check for open bypass valve. (if equipped) Check for low voltage. Check for leak in discharge line. Check for defective or dirty check valve. Check for defective pressure switch. Volt Connection On/Off Switch Fuse Pump 'Model' Number (Here on Label) Wetted Parts Housing: Polypropylene Diaphragm: Liquid Temperature: GPM = Gallons Per Minute PSI = Pounds per Square Inch DC = Direct Current 7xxxx 00000000.. Santoprene 0 F max. Pump 'Serial' Number (Here on Label) Inlet Outlet Page
Exploded View/Parts List: LG-00-0 (00)....................... 0...... 0.. 7..7..... 7.7...... 7 0 Item No Part Number Qty Description 000 Poly Knurled Swivel Nut, /" FGHT 0007 /"- Hex Whiz (Flange) Locknut 00 Garden Hose Washer 00 Hose, /"- Brd. x Ft. 00 Hose, /"- Brd. x " 00.0/.0- Wheel (White) w/ /" Offset & /" BB 7 00 Axle (/" Dia. x -/") 00 H.H.C.S. /"-nc x /" Long 00 H.H.C.S. /"-nc x " Long 0 0 /"- x /" Flange Lock Screw 07 Hitch Bracket (Formed) 0 Hitch Bracket (Flat) 0 /" Black Nylon Loom Cable Clamp 0 Hose Clamp (/") 0 Tank Lid w/lanyard 0700 Trailer Frame (-0 Gal) (Red) 7 070 Grommet 0 Boom Bracket (Light Duty) 00 Poly Bypass "J" Hose (./. - Gal.) 0 00 Siphon Tube 0077 Cotter Pin, /" x " 77 #0- x /" Phillips Truss Head Machine Screw 7 #0- x /" Phillips Truss Head Machine Screw 7 #0- x /" Truss Head Machine Screw 7 Bushing (/0 Gallon Trailer) 7 Manifold Spacer (.gpm) 7 7007 Gauge, 0-00 p.s.i. Gallon (New Style) Tank 7 Deluxe Pistol-Grip Handgun w/x- 0 77 Drain Plug Cap, Tether, and Washer Assembly 7 Lead Wire Assembly (w/switch), " 70 Handgun Clips & Screws (Pkg/) (#0- Thread) Item No Part Number Qty Description 770 Gold Series. g.p.m. Pump (0 psi, Amp) 777 Intake Sub-Assembly. Nylon Shut-Off Valve (/" GHT). Port Kit Fitting, /" Hose Barb. Strainer, " Filter Washer. 0 Poly Swivel, /" Hose Barb. 000 Poly Knurled Swivel Nut, /" FGHT. 007 /" Polyspring Hose x ".7 0 Hose Clamp (/"-/") 77 Manifold Assembly (Trailer/ATV). 000 Port Kit Elbow, /" FNPT. 0 Manifold w/mounting Tab. Nylon Shut-Off Valve (/" GHT). 00 Garden Hose Washer. 0 Poly Swivel, /" Hose Barb. 000 Poly Knurled Swivel Nut, /" FGHT.7 00 Poly Elbow, /" FNPT x /" FNPT. 007 Poly Reducing Bushing, /" MNPT x /" FNPT 7777 -Nozzle Boom (QJ). 0 Boom Mount Angle - Nozzle (QJ00). 00 Plastic Retaining Clip Ga. & Ga.. 77 -Nozzle Harness (/").. 0 Hose Clamp (/").. 000 Hose, /"- Brd. x -/".. 77 ELL Nozzle Sub-Assembly (/")... 0 Single Hose Shank (/" Hose)... 0 Nozzle Strainer, Red (0 Mesh)... 07 Turbo FloodJet (TF-VP)... 0 QJ Cap Only (Black)... 07 Seat Washer (QJ Caps).. 00 Poly Hose Tee, /" HB. 0 Nylon Cable Tie Page
After ing After use, fill the sprayer tank part way with water. Start the sprayer, and allow the clear water to be pumped through the plumbing system and out through the spray nozzles. Refill the tank about half full with plain water and use FIMCO Tank Neutralizer and Cleaner, and repeat cleaning instructions above. Flush the entire sprayer with the neutralizing/cleaning agent, then flush out one more time with plain water. Follow the chemical manufacturer's disposal instructions of all wash or rinsing water. For the boom, (if applicable) remove the tips and screens from the nozzle assemblies. Wash these items out thoroughly. Blow the orifice clean and dry. If the orifice remains clogged, clean it with a fine bristle (NOT WIRE) brush, or with a toothpick. Do not damage the orifice. Water rinse and dry the tips before storing. Winter Storage Drain all water out of your sprayer, paying special attention to the pump, handgun, and valve(s). These items are especially prone to damage from chemicals and freezing weather. The sprayer should be winterized before storage by pumping a solution of RV antifreeze through the entire plumbing system. This antifreeze solution should remain in the plumbing system during the winter months. When spring time comes and you are preparing your sprayer for the spray season, rinse the entire plumbing system out, clearing the lines of the antifreeze solution. Proper care and maintenance will prolong the life of your sprayer. WARNING: Some chemicals will damage the pump valves if allowed to soak untreated for a length of time! ALWAYS flush the pump as instructed after each use. Intake/Siphon Tube/Screen Detail of a Typical L&G/ATV er (not including the 'EC' units) 'Cut' View of a 'Typical' Tank (looking inside) to Inlet of Pump Knurled Nut Siphon Tube Nylon Shut-Off Valve (/" GHT) Strainer, " Filter Washer The suction line of your sprayer should contain a 'siphon tube', or 'intake tube', which should be rotated so that it just touches the bottom of the tank surface. (see Detail Views) Reach in and rotate it, as needed, if not already in this position. A nylon shut-off valve is threaded onto the pipe nipple, at the intake location on the tank. It is at this location so you can shut off the flow of solution, to access your system's screen, for cleaning. Valve "Open" Make sure the siphon tube is rotated so that the tube just touches the bottom of the tank. Checking/Cleaning the sprayer's filter/screen: - Shut the nylon valve to the 'Closed' position. (lever is perpendicular to the flow of fluid) - Unscrew the knurled nut from the shut-off valve, leaving the valve connected to the tank. - Swing (swivel) the intake assembly towards you. Look in the nut you JUST unscrewed. There is a screen/washer there. - Remove the screen and clean as necessary. Replace when done and reassemble the entire assembly. - Make sure the valve in turned to the 'Open' position before restarting your pump. Valve "Closed" Spacer Manifold Screw Manifold Spacer Attachment NOTE: To install the manifold spacer, remove one screw holding the pump to the tank (upper left location as you're looking at the pump) and place the spacer between the manifold and the pump's foot. Replace original screw with the long machine screw, feeding it through the slot in the manifold and through the spacer, thus securing the manifold. This screw will be -/" long for the.gpm pump, and " long for the.gpm pump. This does not apply to units that use a.0 gpm pump. Page