Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D PL 11117 01 00 according to DIN EN ISO/IEC 17025:2005 Period of validity: 08.09.2015 until 10.04.2019 Holder of certificate: TÜV Rheinland LGA Bautechnik GmbH Prüfstelle Baustoffe und Beton, Verkehrswegebau, Werkstoffe Tillystraße 2, 90431 Nürnberg Tests in the fields: Testing of concrete and grout, cement, admixtures and additives for concrete and grout, selected aggregates for concrete and grout, floor screed, building bricks, aerated and lightweight concrete, concrete goods, artificial stone, drainage goods, insulating materials, ceilings, wooden building components, material and construction element testing Tests of mineral construction materials and natural stone Geotechnical ground and soil investigations, sampling and testing of soils, rock and aggregate samples Testing of bituminous materials, road marking materials, coatings as well as hot and cold plastic masses non destructive testing of road surfaces and road areas mechanical structural test methods, tests of reinforcing steel, dynamic materials and components testing, testing of weld seams of metallic materials, metallographic and corrosion testing Test methods (investigation area I and special test methods of investigation area II) by third party testing authorities for the installation of mineral construction materials in landfill liner systems according to the Landfill Ordinance DepV and Federal Uniform Quality Standard BQS 9 1 Testing of construction products and testing of fire resistance within the framework of EU Regulation No. 305/2011 laying down the harmonised conditions for the marketing of construction products (Construction Products Regulation CPR) Abbreviations used: see last page This document is a translation. The definitive version is the original German annex to the accreditation certificate. 1/52
The testing laboratory is permitted, without being required to inform and obtain prior approval from DAkkS, to use standard testing methods listed here with different issue dates. This is valid for all areas of accreditation scope with the exception of section 4 (CPR). 1 Tests of concrete adhesives, concrete, grout, floor screed, building bricks and masonry, admixtures and additives, mineral building products and natural stones 1.1 Binders and concrete DIN EN 196 1 2005 05 DIN EN 196 2 2013 10 DIN EN 196 3 2009 02 DIN EN 196 6 2010 05 DIN EN 196 7 2008 02 Methods of testing cement Part 1: Determination of strength Method of testing cement Part 2: Chemical analysis of cement Methods of testing cement Part 3: Determination of setting times and soundness Methods of testing cement Part 6: Determination of fineness Methods of testing cement Part 7: Methods of taking and preparing samples of cement The above listed standards are to be used in connection with the following guidance documents: DIN EN 197 1 2011 11 DIN EN 197 2 2012 01 DIN EN 450 1 2012 10 Cement Part 1: Composition, specifications and conformity criteria for common cements Cement Part 2: Conformity evaluation Cement Part 1: Composition, specifications and conformity criteria for common cements DIN EN 451 2 1995 01 DIN EN 1015 3 2007 05 Method of testing fly ash Part 2: Determination of fineness by wet sieving Methods of test for mortar for masonry Part 3: Determination of consistence of fresh mortar (by flow table) Period of validity: 08.09.2015 to 10.04.2019 Translation 2/52
DIN EN 13454 2 2007 11 Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate Part 2: Test methods in connection with: DIN EN 13454 1 2005 1 Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate Part 1: Definitions and requirements DIN EN 413 2 2005 08 DIN EN 520 2009 12 DIN 51043 1979 08 DIN EN 480 1 2011 09 DIN EN 480 2 2006 11 DIN EN 480 4 2006 03 DIN EN 480 11 2005 12 DIN EN 934 6 2006 03 Masonry cement Part 2: Test methods Gypsum plasterboards Definitions, requirements and test methods Trass Requirements, Tests Admixtures for concrete, mortar and grout Test methods Part 1: Reference concrete and reference mortar for testing Admixtures for concrete, mortar and grout Test methods Part 2: Determination of setting time Admixtures for concrete, mortar and grout Test methods Part 4: Determination of bleeding of concrete Admixtures for concrete, mortar and grout Test methods Part 11: Determination of air void characteristics in hardened concrete Admixtures for concrete, mortar and grout Part 6: Sampling, conformity control and evaluation of conformity The above listed standards are to be used in connection with the following guidance documents: DIN EN 12518 2008 04 Chemicals used for treatment of water intended for human consumption High calcium lime DIN EN 445 2008 01 Grout for prestressing tendons Test methods Period of validity: 08.09.2015 to 10.04.2019 Translation 3/52
DIN EN 12350 1 2009 08 DIN EN 12350 2 2009 08 DIN EN 12350 3 2009 08 DIN EN 12350 4 2009 08 DIN EN 12350 5 2009 08 DIN EN 12350 6 2011 03 DIN EN 12350 7 2009 08 DIN EN 12350 8 2010 12 DIN EN 12350 11 2010 12 DIN EN 12350 12 2010 12 DIN EN 12504 1 2009 07 DIN EN 12504 2 2012 12 DIN 1048 5 1991 06 DIN EN 12390 1 2012 12 Testing fresh concrete Part 1: Sampling Testing fresh concrete Part 2: Slump test Testing fresh concrete Part 3: Vebe test Testing fresh concrete Part 4: Degree of compactibility Testing fresh concrete Part 5: Flow table test Testing fresh concrete Part 6: Density Testing fresh concrete Part 7: Air content Pressure methods Testing fresh concrete Part 8: Self compacting concrete Slumpflow test Testing fresh concrete Part 11: Self compacting concrete Sieve segregation test Testing fresh concrete Part 12: Self compacting concrete J ring test Testing concrete in structures Part 1: Cored specimens Taking, examining and testing in compression Testing concrete in structures Part 2: Non destructive testing Determination of rebound number Testing concrete testing of hardened concrete (specimens prepared in mould) Testing hardened concrete Part 1: Shape, dimensions and other requirements for specimens and moulds Period of validity: 08.09.2015 to 10.04.2019 Translation 4/52
DIN EN 12390 2 2009 08 + Corrigenda 1 2012 02 DIN EN 12390 3 2009 07 + Corrigenda 1 2011 11 DIN EN 12390 5 2009 07 DIN EN 12390 6 2010 09 DIN EN 12390 7 2009 07 DIN EN 12390 8 2009 07 ZTV Ing, Teil 1 2012 03 Testing hardened concrete Part 2: Making and curing specimens for strength tests Testing hardened concrete Part 3: Compressive strength of test specimens (withdrawn standard) Testing hardened concrete Part 5: Flexural strength of test specimens Testing hardened concrete Part 6: Tensile splitting strength of test specimens Testing hardened concrete Part 7: Density of hardened concrete Testing hardened concrete Part 8: Depth of penetration of water under pressure Additional terms of contract and guidelines for structural Engineering general part 3 tests during construction part 3.3 The above listed standards are to be used in connection with the following guidance documents: ZTV Ing, Teil 3 2012 03 DAfStB RiLi Schutz und Instandsetzung von Betonbauteilen 2001 10 Additional terms of contract and guidelines for structural Engineering solid structure part 4 protection and maintenance of concrete building parts annex B determination of concrete humidity with the CM device DAfStB guideline for protection and maintenance of concrete building parts part 3: requirements for service companies and surveillance of execution DAfStb RiLi Wassergefährdende Stoffe 2011 11 DAfStb Heft 422 1991 DAfStb guideline for concrete structural engineering using water polluting substances annex A: test method (only test method A2) Testing of concrete advice and hints as in addition to DIN 1048, only chapters 2.2, 2.5, 2.6 und 3.3 Period of validity: 08.09.2015 to 10.04.2019 Translation 5/52
The above listed standards are to be used in connection with the following guidance document: DAStb Richtline 2010 03 Steel fibre concrete DIN 1048 2 1991 06 DIN 1048 4 1991 06 DIN EN 13791 2008 05 DIN EN 14488 1 2005 11 DIN EN 14488 3 2006 09 DIN EN 14488 4 2008 08 DIN EN 14488 6 2006 09 DIN EN 14488 7 2006 08 DIN EN 14845 1 2007 09 DIN EN 14845 2 2006 11 Testing concrete testing of hardened concrete (specimens taken in situ) Test methods for concrete determination of the compressive strength in hardened concrete in structures and components application of reference lines and evaluation with special methods Assessment of in situ compressive strength in structures and precast concrete components Testing sprayed concrete Part 1: Sampling fresh and hardened concrete Testing sprayed concrete Part 3: Flexural strengths (first peak, ultimate and residual) of fibre reinforced beam specimens Testing sprayed concrete Part 4: Bond strength of cores by direct tension Testing sprayed concrete Part 6: Thickness of concrete on a substrate Testing sprayed concrete Part 7: Fibre content of fibre reinforced concrete Test methods for fibres in concrete Part 1: Reference concretes Test methods for fibres in concrete Part 2: Effect on concrete The above listed standards are to be used in connection with the following guidance documents: DIN EN 14889 1 2006 11 DIN EN 14889 2 2006 11 Fibres for concrete Part 1: Steel fibres Definitions, specifications and conformity Fibres for concrete Part 2: Polymer fibres Definitions, specifications and conformity Period of validity: 08.09.2015 to 10.04.2019 Translation 6/52
DIN 1100 2004 05 Hard aggregates for cement bound floor screeds Requirements and test methods Other applicable documents: ONR 23303 2010 03 ÖNORM B 4706 2008 12 Test methods for concrete National application of testing standards for concrete and its source materials Repair, reconstruction and strengthening of concrete structures 1.2 Grout DIN 272 1986 02 DIN EN 1308 2007 11 Testing of magnesium oxychloride screeds Adhesives for tiles Determination of slip The above listed standards are to be used in connection with the following guidance document: DIN EN 1323 2007 11 Adhesives for tiles Concrete slabs for tests DIN EN 1324 2007 11 DIN EN 1346 2007 11 DIN EN 1347 2007 10 DIN EN 1348 2007 11 DIN EN 1015 1 2007 05 DIN EN 1015 2 2007 05 Adhesives for tiles Determination of shear adhesion strength of dispersion adhesives Adhesives for tiles Determination of open time Adhesives for tiles Determination of wetting capability Adhesives for tiles Determination of tensile adhesion strength for cementitious adhesives Methods of test for mortar for masonry Part 1: Determination of particle size distribution (by sieve analysis) Methods of test for mortar for masonry Part 2: Bulk sampling of mortars and preparation of test mortars Period of validity: 08.09.2015 to 10.04.2019 Translation 7/52
DIN EN 1015 3 2007 05 DIN EN 1015 4 1998 12 DIN EN 1015 6 2007 05 DIN EN 1015 7 1998 12 DIN EN 1015 9 2007 05 DIN EN 1015 10 2007 05 DIN EN 1015 11 2007 05 DIN EN 1015 12 2000 06 DIN EN 1015 18 2003 03 DIN EN 1015 19 2005 01 DIN EN 12002 2009 01 DIN EN 12003 2009 01 Methods of test for mortar for masonry Part 3: Determination of consistence of fresh mortar (by flow table) Methods of test for mortar for masonry Part 4: Determination of consistence of fresh mortar (by plunger penetration) Methods of test for mortar for masonry Part 6: Determination of bulk density of fresh mortar Methods of test for mortar for masonry Part 7: Determination of air content of fresh mortar Methods of test for mortar for masonry Part 9: Determination of workable life and correction time of fresh mortar Methods of test for mortar for masonry Part 10: Determination of dry bulk density of hardened mortar Methods of test for mortar for masonry part 11: determination of flexural and compressive strength of hardened mortar Methods of test for mortar for masonry Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates Methods of test for mortar for masonry Part 18: Determination of water absorption coefficient due to capillary action of hardened mortar Methods of test for mortar for masonry Part 19: Determination of water vapour permeability of hardened rendering and plastering mortars Adhesives for tiles Determination of transverse deformation for cementitious adhesives and grouts Adhesive for tiles Determination of shear adhesion strength of reaction resin adhesives The above listed standards are to be used in connection with the following guidance documents: DIN EN 12004 2012 09 Adhesives for tiles Requirements, evaluation of conformity, classification and designation Period of validity: 08.09.2015 to 10.04.2019 Translation 8/52
DIN EN 12004 2014 02 Adhesives for tiles Requirements, evaluation of conformity, classification and designation DIN 18555 1 1982 09 DIN 18555 2 1982 09 DIN 18555 3 1982 09 DIN 18555 4 1986 03 DIN 18555 5 1986 03 DIN 18555 6 1987 11 DIN 18555 7 1987 11 DIN 18555 8 1987 11 DIN 18555 9 1999 09 DIN 18556 1985 01 Testing of mortars containing mineral binders general, sampling, test mortar (withdrawn standard) Testing of mortars containing mineral binders freshly mixed mortars containing aggregates of dense structure (heavy aggregates) determination of consistence, bulk density and air content (withdrawn standard) Testing of mortars containing mineral binders hardened mortars determination of flexural strength, compressive strength and bulk density Testing of mortars containing mineral binders hardened mortars determination of linear and transverse strain and of deformation characteristics of masonry mortars by the static pressure test Testing of mortars containing mineral binders hardened mortars determination of bond shear strength of masonry mortars (withdrawn standard) Testing of mortars containing mineral binders determination of bond strength of hardened mortar Testing of mortars containing mineral binders determination of water retentivity of freshly mixed mortar by the filter plate method Testing of mortars containing mineral binders freshly mixed mortar determination of workability time and correction time of thinbed mortar for use with masonry (withdrawn standard) Testing of mortars containing mineral binders Part 9: Hardened mortars determination of the mortar compressive strength in the bed joint Testing of coating material for synthetic resin plasters and of synthetic resin plasters (withdrawn standard) Period of validity: 08.09.2015 to 10.04.2019 Translation 9/52
1.3 Screeds DIN EN 13892 1 2003 02 DIN EN 13892 2 2003 02 DIN EN 13892 3 2004 07 DIN EN 13892 8 2003 02 Methods of test for screed materials Part 1: Sampling, making and curing specimens for test Methods of test for screed materials Part 2: Determination of flexural and compressive strength Methods of test for screed materials Part 3: Determination of wear resistance Böhme Methods of test for screed materials Part 8: Determination of bond strength The above listed standards are to be used in connection with the following guidance documents: DIN EN 13813 2003 01 DIN 18560 1 2009 09 DIN 18560 2 2009 09 DIN 18560 3 2006 03 DIN 18560 4 2012 06 DIN 18560 7 2004 04 Screed material and floor screeds Screed materials Properties and requirements Floor screeds in building construction Part 1: General requirements, testing and construction Floor screeds in building construction Part 2: Floor screeds and heating floor screeds on insulation layers Floor screeds in building construction Part 3: Base bonded floor screeds Floor screeds Part 4: Screeds laid on separated layer Floor screeds Part 7: Heavy duty screeds (industrial screeds) 1.4 Building bricks and masonry DIN EN 846 2 2000 08 DIN EN 846 3 2000 08 Methods of tests for ancillary components for masonry Part 2: Determination of bond strength of prefabricated bed joint reinforcement in mortar joints Methods of tests for ancillary components for masonry Part 3: Determination of shear load capacity of welds in prefabricated bed joint reinforcement Period of validity: 08.09.2015 to 10.04.2019 Translation 10/52
DIN EN 846 4 2005 01 DIN EN 846 5 2012 11 DIN EN 846 6 2012 11 DIN EN 846 7 2012 11 DIN EN 846 8 2006 10 DIN EN 846 9 2000 08 DIN EN 846 10 2000 08 DIN EN 846 11 2000 08 DIN EN 846 13 2001 12 DIN EN 772 1 2011 07 DIN EN 772 6 2002 02 DIN EN 772 14 2002 02 Methods of test for ancillary components for masonry Part 4: Determination of load capacity and load deflection characteristics of straps Methods of test for ancillary components for masonry Part 5: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (couplet test) Methods of test for ancillary components for masonry Part 6: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (single end test) Methods of test for ancillary components for masonry Part 7: Determination of shear load capacity and load displacement characteristics of shear ties and slip ties (couplet test for mortar joint connections) Methods of tests for ancillary components for masonry Part 8: Determination of load capacity and load deflection characteristics of joist hangers Methods of tests for ancillary components for masonry Part 9: Determination of flexural resistance and shear resistance of lintels Methods of test for ancillary components for masonry Part 10: Determination of load capacity and load deflection characteristics of brackets Methods of test for ancillary components for masonry Part 11: Determination of dimensions and bow of lintels Methods of test for ancillary components for masonry Part 13: Determination of resistance to impact, abrasion and corrosion of organic coatings Methods of test for masonry units Part 1: Determination of compressive strength Methods of test for masonry units Part 6: Determination of bending tensile strength of aggregate concrete masonry units Methods of test for masonry units Part 14: Determination of moisture movement of aggregate concrete and manufactured stone masonry units Period of validity: 08.09.2015 to 10.04.2019 Translation 11/52
DIN EN 772 15 2000 09 Methods of test for masonry units Part 15: Determination of water vapour permeability of autoclaved aerated concrete masonry units The above listed standards are to be used in connection with the following guidance documents: DIN EN 845 1 2013 10 DIN EN 845 2 2013 08 DIN EN 845 3 2013 08 DIN V 18151 100 2005 10 DIN V 18152 100 2005 10 DIN V 18153 100 2005 10 DIN 105 100 2012 01 Specification for ancillary components for masonry Part 1: Wall ties, tension straps, hangers and brackets Specification for ancillary components for masonry Part 2: Lintels Specification for ancillary components for masonry Part 3: Bed joint reinforcement of steel meshwork Lightweight concrete hollow blocks Part 100: Hollow blocks with specific properties Lightweight concrete solid bricks and blocks Part 100: Solid bricks and blocks with specific properties Concrete masonry units (Normal weight concrete) Part 100: Masonry units with specific properties Clay masonry units Part 100: Clay masonry units with specific properties 1.5 Aerated and lightweight concrete DIN EN 678 1994 02 DIN EN 679 2005 09 DIN EN 680 2006 03 DIN EN 990 2003 01 Determination of the dry density of autoclaved aerated concrete Determination of the compressive strength of autoclaved aerated concrete Determination of the drying shrinkage of autoclaved aerated concrete Test methods for verification of corrosion protection of reinforcement in autoclaved aerated concrete and lightweight aggregate concrete with open structure Period of validity: 08.09.2015 to 10.04.2019 Translation 12/52
DIN EN 991 1995 09 DIN EN 992 1995 09 DIN EN 1351 1997 02 DIN EN 1352 1997 02 DIN EN 1353 1997 02 DIN EN 1354 2005 09 Determination of the dimensions of prefabricated reinforced components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure Determination of the dry density of lightweight aggregate concrete with open structure Determination of flexural strength of autoclaved aerated concrete Determination of static modulus of elasticity under compression of autoclaved aerated concrete or lightweight aggregate concrete with open structure Determination of moisture content of autoclaved aerated concrete Determination of compressive strength of lightweight aggregate concrete with open structure The above listed standards are to be used in connection with the following guidance documents: DIN V 4165 100 2005 10 DIN 4166 1997 10 Autoclaved aerated concrete masonry units Part 100: High precision units and elements with specific properties Autoclaved aerated concrete slabs and panels 1.6 physical performance of construction products DIN EN ISO 12571 2013 12 DIN EN ISO 12572 2001 09 DIN EN 12667 2001 05 Hygrothermal performance of building materials and products Determination of hygroscopic sorption properties Hygrothermal performance of building materials and products Determination of water vapour transmission properties Thermal performance of building materials and products Determination of thermal resistance by means of guarded hot plate and heat flow meter methods Products of high and medium thermal resistance Period of validity: 08.09.2015 to 10.04.2019 Translation 13/52
1.7 Roof panels, insulating materials, wooden structures, planked ceiling and suspended ceilings DIN EN 492 2012 12 DIN EN 494 2013 01 DIN EN 822 2013 05 DIN EN 823 2013 05 DIN EN 824 2013 05 DIN EN 825 2013 05 DIN EN 826 2013 05 DIN EN 1602 2013 05 DIN EN 1607 2013 05 DIN EN 1608 2013 05 DIN EN 1609 2013 05 DIN EN 12086 2013 06 DIN EN 12087 2013 06 Fibre cement slates and fittings Product specification and test methods, except 7.3.3, 7.4.2 und 7.5 Fibre cement profiled sheets and fittings Product specification and test methods, only 7.3.1 and 7.3.2 Thermal insulating products for building applications Determination of length and width Thermal insulating products for building applications Determination of thickness Thermal insulating products for building applications Determination of squareness Thermal insulating products for building applications Determination of flatness Thermal insulating products for building applications Determination of compression behaviour (here: without determination of 10% compression) Thermal insulating products for building applications Determination of the apparent density Thermal insulating products for building applications Determination of tensile strength perpendicular to faces Thermal insulating products for building applications Determination of tensile strength parallel to faces Thermal insulating products for building applications Determination of short term water absorption by partial immersion Thermal insulating products for building applications Determination of water vapour transmission properties Thermal insulating products for building applications Determination of water vapour transmission properties Period of validity: 08.09.2015 to 10.04.2019 Translation 14/52
DIN EN 12089 2013 06 DIN 4158 1978 05 DIN 1052 10 2012 05 DIN EN 1382 2000 03 DIN EN 1383 2000 03 DIN EN 14592 2012 07 DIN EN 14195 2011 11 DIN EN 14316 1 2004 11 DIN 18168 2 2008 05 Thermal insulating products for building applications Determination of bending behaviour Filler concrete joists for reinforced and prestressed concrete floors Design of timber structures Part 10: Additional provisions Timber structures Test methods Withdrawel capacity of timber fasteners Timber structures Test methods Pull through resistance of timber fasteners Timber structures Dowel type fasteners Requirements Metal framing components for gypsum board systems Definitions, requirements and test methods Thermal insulation products for buildings In situ thermal insulation formed from expanded perlite (EP) products Part 1: Specification for bonded and loose fill products before installation Ceiling linings and suspended ceilings with gypsum plasterboards Part 2: Verification of the load carrying capacity of metal subconstructions and metal suspending rods in connection with : DIN 18168 1 2007 04 Ceiling linings and suspended ceilings with gypsum plasterboards Part 1: Requirements for construction DIN EN 13964 2014 08 ETAG 003 1999 Suspended ceilings Requirements and test methods Guideline for european technical approval of internal partition kits for use as non loadbearing walls Period of validity: 08.09.2015 to 10.04.2019 Translation 15/52
1.8 Cast stones DIN V 18500 2006 12 Cast stones Terminology, requirements, testing, inspection in connection with : DIN 483 2005 10 Concrete kerb units Shapes, dimensions, marking DIN EN 1338 2003 08 + Corrigenda 1 2006 11 E DIN EN 1338 2010 08 Bundesverband Deutsche Beton und Fertigteilindustrie e.v., Bonn 1996 04 DIN EN 1339 2003 08 + Corrigenda 1 2006 11 E DIN EN 1339 2010 08 DIN EN 1340 2003 08 + Corrigenda 1 2006 11 E DIN EN 1340 2010 08 DIN EN 13748 1 2005 08 DIN EN 13748 2 2005 03 Concrete paving blocks Requirements and test methods, not annex G Concrete paving blocks Requirements and test methods, not annex G Guideline, production and quality assurance of permeable concrete paving blocks made of open matrix concrete Concrete paving flags Requirements and test methods, not annex G Concrete paving flags Requirements and test methods, not annex G Concrete kerb units Requirements and test methods, not annex G Concrete kerb units Requirements and test methods, not annex G Terrazzo tiles Part 1: Terrazzo tiles for internal use, not section 5.6.1 Terrazzo tiles Part 2: Terrazzo tiles for external use, not section 5.6.1 Period of validity: 08.09.2015 to 10.04.2019 Translation 16/52
The above listed standards are to be used in connection with the following guidance document: BGB RINGB 2006 11 Non standardized concrete products Requirements and test methods DIN 19555 2003 04 DIN 19555 Corrigenda 1 2006 04 DIN EN 13101 2003 04 DIN EN 1433 2005 09 DIN EN 124 1994 08 Step irons for single line installation Step irons for setting in concrete Step irons for single line installation Step irons for setting in concrete Steps for underground man entry chambers Requirements, marking, testing and evaluation of conformity Drainage channels for vehicular and pedestrian areas Classification, design and testing requirements, marking and evaluation of conformity Gully tops and manhole tops for vehicular and pedestrian areas design requirements, testing, marking, quality control 1.9 Mineral construction materials DIN EN 932 1 1996 11 Test for general properties of aggregates Part 1: Methods for sampling in connection with : ZTV wwg StB By 05 Az: IID9 43437 002/92 2005 21 12 Additional technical Conditions for contract and delivery for required water management relevant quality parameter for the use of recycled road construction products in Bavaria, only section 6.1 DIN EN 932 2 1999 03 DIN EN 932 3 2003 12 Test for general properties of aggregates Part 2: Methods for reducing laboratory samples Tests for general properties of aggregates Part 3: Procedure and terminology for simplified petrographic description Period of validity: 08.09.2015 to 10.04.2019 Translation 17/52
The above listed standards are to be used in connection with the following guidance document: DIN EN 932 5 2012 05 Tests for general properties of aggregates Part 5: Common equipment and calibration DIN EN 933 1 2012 03 ÖNORM EN 933 1 2012 03 ÖNORM EN 13286 41 2003 06 ÖNORM EN 13286 42 2003 06 DIN EN 933 3 2012 04 DIN EN 933 4 2015 01 DIN EN 933 5 2005 02 DIN EN 933 6 2014 07 DIN EN 933 7 1998 05 Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution Sieving method Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution Sieving method Unbound and hydraulically bound mixtures Part 41: Test method for the determination of the compressive strength of hydraulically bound mixtures Unbound and hydraulically bound mixtures Part 42: Test method for the determination of the indirect tensile strength of hydraulically bound mixtures Tests for geometrical properties of aggregates Part 3: Determination of particle shape Flakiness index Tests for geometrical properties of aggregates Part 4: Determination of particle shape Shape index Tests for geometrical properties of aggregates Part 5: Determination of percentage of crushed and broken surfaces in coarse aggregate particles Tests for geometrical properties of aggregates Part 6: Assessment of surface characteristics Flow coefficient of aggregates Tests for geometrical properties of aggregates Part 7: Determination of shell content percentage of shells in coarse aggregates Period of validity: 08.09.2015 to 10.04.2019 Translation 18/52
DIN EN 933 8 2012 04 DIN EN 933 9 2013 07 DIN EN 933 10 2009 10 DIN EN 933 11 2011 05 DIN 52106 2013 12 DIN EN 1097 1 2011 04 DIN EN 1097 2 2010 07 DIN EN 1097 3 1998 06 DIN EN 1097 4 2008 06 DIN EN 1097 7 2008 06 + Corrigenda 1 2008 09 DIN EN 1097 8 2009 10 Tests for geometrical properties of aggregates Part 8: Assessment of fines Sand equivalent test Tests for geometrical properties of aggregates Part 9: Assessment of fines Methylene blue test Tests for geometrical properties of aggregates Part 10: Assessment of fines Grading of filler aggregates (air jet sieving) Tests for geometrical properties of aggregates Part 11: Classification test for the constituents of coarse recycled aggregate Testing of aggregates Test methods for the assessment of the weathering resistance Tests for mechanical and physical properties of aggregates Part 1: Determination of the resistance to wear (micro Deval) Tests for mechanical and physical properties of aggregates Part 2: Methods for the determination of resistance to fragmentation Tests for mechanical and physical properties of aggregates Part 3: Determination of loose bulk density and voids Tests for mechanical and physical properties of aggregates Part 4: Determination of the voids of dry compacted filler Tests for mechanical and physical properties of aggregates Part 7: Determination of the particle density of filler Pyknometer method Tests for mechanical and physical properties of aggregates Part 8: Determination of the polished stone value Period of validity: 08.09.2015 to 10.04.2019 Translation 19/52
DIN EN 1367 2 2010 02 DIN EN 1367 3 2001 06 + Corrigenda 1 2004 09 DIN EN 1367 5 2011 04 DIN EN 1367 6 2008 12 DIN EN 13055 1 2002 08 + Corrigenda 1 2004 12 E DIN EN 13055 1 2012 05 DIN EN 13055 2 2004 09 DIN 52115 2 2014 02 DIN EN 1744 1 2013 03 Tests for thermal and weathering properties of aggregates Part 1: Determination of resistance to freezing and thawing Tests for thermal and weathering properties of aggregates Part 3: Boiling test for "Sonnenbrand basalt Tests for thermal and weathering properties of aggregates Part 5: Determination of resistance to thermal shock Tests for thermal and weathering properties of aggregates Part 6: Determination of resistance to freezing and thawing in the presence of salt (NaCl) Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applications, not annex B Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applications, not annex B Lightweight aggregates Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications Test methods for aggregates Part 2: Impact test on crushed and broken aggregates larger than 32 mm Tests for chemical properties of aggregates Part 1: Chemical analysis, only chapter. 14.2 und 15.1 DIN EN 13286 2 2013 02 DIN EN 13383 2 2013 08 DIN EN 13450 2013 07 Unbound and hydraulically bound mixtures Part 2: Test methods for laboratory reference density and water content Proctor compaction Armourstone Part 1: Specification Aggregates for railway ballast, only annexes A, C and D Period of validity: 08.09.2015 to 10.04.2019 Translation 20/52
DIN EN 13179 1 2013 09 TP Beton StB 10 Teil 3.1 2010 TP Gestein StB Teil 3.1.4 2008 TP Gestein StB Teil 3.1.5 2008 TP Gestein StB Teil 4.1.3 2008 TP Gestein StB Teil 4.1.4 2008 TP Gestein StB Teil 4.7.1 2008 TP Gestein StB Teil 5.3.1.2 2008 TP Gestein StB Teil 5.4.1 2015 TP Gestein StB Teil 5.4.3 2008 TP Gestein StB Teil 5.6 2008 Tests for filler aggregate used in bituminous mixtures Part 1: Delta ring and ball test TP concrete StB 10 Technical test specifications for load bearing strata with hydraulic Binders and concrete road surfaces, part 3.1 TP aggregates StB: Technische test specification for aggregates for road construction material labelling of household waste incinerator ash (municipal incinerator bottom ash aggregates) Material labelling of recycled construction materials Determination of grain size distribution of fine grain sizes (air jet sieving) Determination of grain size distribution of Filler (air jet sieving) Estimation of ratio rounded to fragmented parts in fine grain sizes using a Binocular Impact test on particle size distributions > 32 mm Los Angeles test method on particle size distributions > 32 mm Determination of polished stone value (PSV fgk ) Determination of hardness Dynamic CBR test Period of validity: 08.09.2015 to 10.04.2019 Translation 21/52
TP Gestein StB Teil 6.3.2 2008 TP Gestein StB Teil 6.3.3 2008 TP Gestein StB Teil 6.5.1 2008 TP Gestein StB Teil 6.5.2 2008 TP Gestein StB Teil 6.6.3 2015 DIN EN 12697 11 2012 07 TP Asphalt StB Teil 11 2012 Resistance of mineral grain size composition against freeze thaw cycles Resistance of fine aggregates against frost and thaw changes Resistance of coarse aggregates against heat exposure Resistance of fine aggregates against heat exposure Water sensitivity of fine aggregates shaking and abrasive method Bituminous mixtures Test methods for hot mix asphalt Part 11: Determination of the affinity between aggregate and bitumen Technical test directives for Asphalt Part 11: adhesion betweenstone and Bitumen 1.10 Natural stone and brick DIN EN 1936 2007 02 DIN EN 13755 2008 08 DIN 52008 2006 03 DIN EN 1926 2007 03 DIN EN 12372 2007 02 Natural stone test method Determination of real density and apparent density, and of total and open porosity Natural stone test methods Determination of water absorption at atmospheric pressure Natural stone test methods Assessment of the weathering resistance, only annexes C and D Natural stone test methods Determination of uniaxial compressive strength Natural stone test methods Determination of flexural strength under concentrated load Period of validity: 08.09.2015 to 10.04.2019 Translation 22/52
DIN EN 13161 2008 08 DIN EN 13364 2002 03 DIN EN 14157 2005 01 DIN 51097 1992 11 DIN 51130 2014 02 DIN EN 538 1994 11 DIN EN 539 1 2005 12 DIN EN 539 2 2013 08 DIN EN 1024 2012 06 Natural stone test methods Determination of flexural strength under constant moment Natural stone test methods Determination of the breaking load at dowel hole Natural stone test methods Determination of the abrasion resistance Testing of floor coverings determination of the anti slip properties wet loaded barefoot areas walking method ramp test Testing of floor coverings Determination of the anti slip property Workrooms and fields of activities with slip danger Walking method Ramp test Clay roofing tiles for discontinuous laying Flexural strength test Clay roofing tiles for discontinuous laying Determination of physical characteristics Part 1: Impermeability test Clay roofing tiles for discontinuous laying Determination of physical characteristics Part 2: Test for frost resistance Clay roofing tiles for discontinuous laying Determination of geometric characteristics Period of validity: 08.09.2015 to 10.04.2019 Translation 23/52
2 Geotechnical site investigation, sampling and testing of soil, rocks and aggregate samples 2.1 Sampling DIN EN ISO 14688 1 2013 12 DIN EN ISO 14688 2 2013 12 DIN EN ISO 14689 1 2011 06 DIN EN ISO 22475 1 2007 01 DIN 4023 2011 01 DIN 19672, Blatt 1 1968 04 DIN 52101 2013 10 Geotechnical investigation and testing Identification and classification of soil Part 1: Identification and description Geotechnical investigation and testing Identification and classification of soil Part 2: Principles for a classification Geotechnical investigation and testing Identification and classification of rock Part 1: Identification and description Geotechnical investigation and testing Sampling methods and groundwater measurements Part 1: Technical principles for execution Geotechnical investigation and testing Graphical presentation of logs of boreholes, trial pits, shafts and adits Apparatus for drawing soil samples in agricultural engineering apparatus for soil sampling in undisturbed situation Aggregates test methods Sampling 2.2 soil and ground physical investigation DIN EN ISO 22476 2 2012 03 FGSV Nr. 591/B 15.1 2012 DIN 4094 4 2002 01 Geotechnical investigation and testing Field testing Part 2: Dynamic probing TP BF StB Technical test guidelines for soil and rock in road construction part B 15.1 Light dynamic probing DPL 5 und middle heavy dynamic probing DPM 10 Construction site tests in situ Part 4: vane shear test Period of validity: 08.09.2015 to 10.04.2019 Translation 24/52
TP BF StB Teil B 8.3 2003 DIN 18035 4 2012 01 DIN 18124 2011 04 DIN 18126 1996 11 DIN 18130 2 2011 07 DIN 18137 1 2010 07 DGGT Empfehlung Nr. 1 2004 DGGT Empfehlung Nr. 2 1986 DGGT Empfehlung Nr. 5 1986 DGGT Empfehlung Nr. 10 1986 DGGT Empfehlung Nr. 11 1986 DGGT Empfehlung Nr. 12 1987 DGGT Empfehlung Nr. 16 1994 Dynamic plate load test using a Drop Weight Tester Sports grounds Part 4: Sports turf areas Soil, investigation and testing Determination of density of solid particles Capillary pycnometer, wide mouth pycnometer, gas pycnometer Soil, investigation and testing Determination of density of noncohesive soils for maximum and minimum compactness Soil, investigation and testing Determination of the coefficient of water permeability Part 2: Field tests Soil, investigation and testing Determination of shear strenght Part 1: Concepts and general testing conditions Uniaxiale load tests on rock samples Triaxiale load tests on rock samples Point load tests on rock samples Indirect tensile test on rock samples tension fatigue test Swelling pressure test on rock samples Multistep technic for triaxial load tests and direct tensile tests Uni and triaxial creep tests on rock samples Period of validity: 08.09.2015 to 10.04.2019 Translation 25/52
QMA 4.3 05.5 303 2013 10 Swelling pressure tests in connection with : DGGT Empfehlung Nr. 11 1986 Swelling pressure test on rock samples DIN EN 932 3 2003 12 Tests for general properties of aggregates Part 3: Procedure and terminology for simplified petrographic description 2.3 Test methods (investigation area I) by third party testing authorities for the installation of mineral construction materials in landfill liner systems according to the Landfill Ordinance DepV and Federal Uniform Quality Standard BQS 9 1 DIN 18121 1 1998 04 DIN 18121 2 2012 02 DIN 18122 1 1997 07 DIN 18123 2011 04 DIN 18125 1 2010 07 DIN 18125 2 1999 08/2011 03* DIN 18127 1997 11/2012 09* DIN 18128 1990 11/2002 12* Soil, investigation and testing Water content Part 1: Determination by drying in oven Soil, investigation and testing Water content Part 2: Determination by rapid methods Soil, investigation and testing Consistency limits Part 1: Determination of liquid limit and plastic limit Soil, investigation and testing Determination of grain size distribution Soil, investigation and testing Determination of density of soil Part 1: Laboratory tests Soil investigation and testing Determination of density of soil Part 2: Field tests (Edition 1999 11 replaced) Soil, investigation and testing Proctor test (Edition 1997 11 replaced) Soil Investigation and testing Determination of ignition loss (Edition 1990 11 replaced) DIN 18129 1996 11/2010 10/ 2011 07* Soil, investigation and testing Determination of lime content (Edition 1996 11 und 2010 10 replaced) Period of validity: 08.09.2015 to 10.04.2019 Translation 26/52
DIN 18130 1 1998 05 DIN 18132 1995 12/2012 04* DIN 18134 2012 04* DIN 19682 1 2007 11 DIN 19682 2 2007 11/2013 08/ 2014 07* GDA E 3 12 (Nr. 3.6):2011 GDA Empfehlungen 3. Auflage 1997 S.268 Überarbeitung 4/2011 Soil investigation and testing Determination of the coefficient of water permeability Part 1: Laboratory tests Soil, testing procedures and testing equipment Determination of water absorption (Edition 1995 12 replaced) Soil Testing procedures and testing equipment Plate load test (Edition 2001 09 and 2010 04 replaced) Soil quality Field tests Part 1: Determination of soil colour Soil quality Field tests Part 2: Determination of soil texture (Edition 2007 11 und 2013 08 replaced) Acceptance test of mineral drainage layers para. 3.6 total carbonate content 2.4 Test methods (Investigation area II) by third party testing authorities for the installation mineral construction materials in landfill liner systems according to the Landfill Ordinance DepV and Federal Uniform Quality Standard BQS 9 1 DIN EN 932 1 1996 11 DIN EN 932 2 1999 03 DIN EN 1097 5 2008 06 + Corrigenda 1 2008 09 DIN EN 1097 6 2005 12/2013 09 DIN EN 1367 1 2007 06 DIN 18122 2 2000 09 Test for general properties of aggregates Part 1: Methods for sampling Test for general properties of aggregates Part 2: Methods for reducing laboratory samples Tests for mechanical and physical properties of aggregates Part 5: Determination of the water content by drying in a ventilated oven Tests for mechanical and physical properties of aggregates Part 6: Determination of particle density and water absorption (Edition 2005 12 replaced) Tests for thermal and weathering properties of aggregates Part 1: Determination of resistance to freezing and thawing Soil investigation and testing Part 2: Determination of the shrinkage limit Period of validity: 08.09.2015 to 10.04.2019 Translation 27/52
DIN 18135 2011 04/2012 04 DIN 18136 2003 11 DIN 18137 2 1990 12/2011 04* DIN 18137 3 2002 09 DIN 4094 2 1990 12/2003 05 Investigation and testing Oedometer consolidation test (Edition 2011 04 replaced) Soil Investigation and testing Unconfined compression test Soil, investigation and testing Determination of shear strength Part 2: Triaxial test (Edition 1990 12 replaced) Soil, investigation and testing Determination of shear strength Part 3: Direct shear test Construction site tests in situ part 2: Standard Penetration Test (Edition 1990 12 replaced) Other applicable documents (for Investigation areas I and II) DIN EN 12620 2008 07 DIN 18196 2006 06/2011 05* Aggregates for concrete Earthworks and foundation soil classification for civil engineering purposes (Edition 2006 06 replaced) *Previous editions already replaced new versions, but still remain as basis of BQS 2.5 Testing of bituminous construction materials DIN EN 12697 20 2012 06 TP Asphalt StB Teil 20 2007 Bituminous mixtures Test methods for hot mix asphalt Part 20: Indentation using cube or cylindrical specimens Technical testing of asphalt Part 20: Intrusion depth on cubic samples DIN EN 12697 27 2001 04 TP Asphalt StB Teil 27 2012 Bituminous mixtures Test methods for hot mix asphalt Part 27: sampling Technical guidelines for bituminous mixtures Part 27: sampling Period of validity: 08.09.2015 to 10.04.2019 Translation 28/52
DIN EN 12697 28 2001 04 TP Asphalt StB Teil 28 2007 DIN EN 12697 30 2012 06 TP Asphalt StB Teil 30 2007 DIN EN 12697 1 2012 09 TP Asphalt StB Teil 1 2012 DIN EN 12697 3 2013 08 TP Asphalt StB Teil 3 2007 DIN EN 12697 5 2010 04 TP Asphalt StB Teil 5 2012 DIN EN 12697 6 2012 07 TP Asphalt StB Teil 6 2012 DIN EN 12697 8 2003 06 TP Asphalt StB Teil 8 2012 DIN EN 12697 2 2007 11 Bituminous mixtures Test methods for hot mix asphalt Part 28: Preparation of samples for determining binder content, water content and grading Technical test guidelines for bituminous mixtures Part 28: Preparation of samples Bituminous mixtures Test methods for hot mix asphalt Part 30: Specimen preparation by impact compactor Technical test guidelines for bituminous mixtures Part 30: making of test specimens with the impact compactor (MVG) Bituminous mixtures Test methods for hot mix asphalt Part 1: Soluble binder content Technical test guidelines for bituminous mixtures Part 1: Soluble binder content Bituminous mixtures Test methods for hot mix asphalt Part 3: Bitumen recovery: Rotary evaporator Technical test guidelines for bituminous mixtures Part 3: Bitumen recovery: Rotary evaporator Technical test guidelines for bituminous mixtures Part 5: Determination of the maximum density Technical test guidelines for bituminous mixtures Part 5: Determination of the maximum density Bituminous mixtures Test methods for hot mix asphalt Part 6: Determination of bulk density of bituminous specimens Technical test guidelines for bituminous mixtures Part 6: Determination of bulk density of bituminous specimens Bituminous mixtures Test methods for hot mix asphalt Part 8: Determination of the air voids content of bituminous specimen Technical test guidelines for bituminous mixtures Part 8: Determination of the air voids content of bituminous specimen and degree of compaction Bituminous mixtures Test method for hot mix asphalt Part 2: Determination of particle size distribution Period of validity: 08.09.2015 to 10.04.2019 Translation 29/52
TP Asphalt StB Teil 2 2010 DIN EN 12697 35 2007 10 TP Asphalt StB Teil 35 2007 DIN EN 12697 13 2001 04 TP Asphalt StB Teil 13 2007 DIN EN 12697 18 2004 10 TP Asphalt StB Teil 18 2007 DIN EN 12697 29 2002 12 TP Asphalt StB Teil 29 2007 TP Asphalt StB Teil 80 2012 ÖNORM B 3639 1 1997 07 ÖNORM B 3639 2 1997 07 ÖNORM EN 12697 36 1997 07 DIN EN 1425 2012 07 DIN EN 1426 2007 06 Technical test guidelines for bituminous mixtures Part 2: Determination of particle size distribution Bituminous mixtures Test methods for hot mix asphalt Part 35: Laboratory mixing Technical test guidelines for bituminous mixtures Part 35: Laboratory mixing Bituminous mixtures Test methods for hot mix asphalt Part 13: Temperature measurement Technical test guidelines for bituminous mixtures Part 13: Temperature measurement Bituminous mixtures Test methods for hot mix asphalt Part 18: Binder drainage Technical test guidelines for bituminous mixtures Part 18: Drain of stone mastic asphalt and porous asphalt Bituminous mixtures Test method for hot mix asphalt Part 29: Determination of the dimensions of bituminous specimen Technical test guidelines for bituminous mixtures Part 29: Determination of dimensions of bituminous specimen Technical test guidelines for bituminous mixtures Part 80: Shear test Asphalts for road construction and related purposes Testing Shear resistance in contact surfaces of asphalt layers Asphalts for road construction and related purposes Testing Pull off resistance in contact surfaces of asphalt layers Bituminous mixtures Test methods for hot mix asphalt Part 36: Determination of the thickness of a bituminous pavement Bitumen and bituminous binders Characterisation of perceptible properties Bitumen and bituminous binders Determination of needle penetration Period of validity: 08.09.2015 to 10.04.2019 Translation 30/52
E DIN EN 1426 2013 09 DIN EN 1427 2007 06 E DIN EN 1427 2013 09 DIN EN 13398 2010 10 DIN 52013 2007 06 DIN EN 12594 2007 06 DIN EN 12594 2015 01 DIN EN 12607 1 2013 12 DIN EN 14769 2012 08 DIN EN 14770 2012 08 DIN EN 14771 2012 08 Multiple tress Creep and Recovery Test AL MSCR Prüfung (DSR) 2012 Bitumen and bituminous binders Determination of needle penetration Bitumen and bituminous binders Determination of the softening point Ring and Ball method Bitumen and bituminous binders Determination of the softening point Ring and Ball method Bitumen and bituminous binders Determination of the elastic recovery of modified bitumen Bitumen and bituminous binders Determination of ductility Bitumen and bituminous binders Preparation of test samples Bitumen and bituminous binders Preparation of test samples Bitumen and bituminous binders Determination of the resistance to hardening under the influence of heat and air Part 1: RTFOT method Bitumen and bituminous binders Accelerated long term ageing conditioning by a Pressure Ageing Vessel (PAV) Bitumen and bituminous binders Determination of complex shear modulus and phase angle using a Dynamic Shear Rheometer (DSR) Bitumen and bituminous binders Determination of the flexural creep stiffness Bending Beam Rheometer (BBR) Guideline fort the determination of deformation of Bitumen and bituminous binders using a Dynamic Shear Rheometer (DSR) execution of MSCR test 2.6 Testing of road marking materials DIN EN 12802 2011 12 Road marking materials Laboratory methods for identification Period of validity: 08.09.2015 to 10.04.2019 Translation 31/52
DIN EN 1436 2009 01 DIN EN 1423 2013 03 DIN EN 1424 2003 08 ZTV M 02 Teil 6.2.1 2002 ZTV M 02 Teil 6.2.2 2002 ZTV M 02 Teil 6.2.3 2002 ZTV M 02 Teil 6.2.4 2002 ZTV M 02 Teil 6.2.5 2002 ZTV M 02 Teil 6.2.6 2002 ZTV M 02 Teil 6.2.7 2002 Road marking materials Road marking performance for road users Road marking materials Drop on materials Glass beads, antiskid aggregates and mixtures of the two Road marking materials Premix glass beads Testing of height overhang, milling depth, milling width and milling length Examination of the amount supernatant Testing of drop on materials Testing of trafficability (drying time) Testing of day visibility Testing of night visibility Testing of skid resistance Testing of wear resistance (life time) 2.7 Testing of road equipment DIN EN 40 3 1 2013 06 EN 40 3 1 2013 02 DIN EN 40 3 2 2013 06 EN 40 3 2 2013 02 Lighting columns Part 3 1: Design and verification Specification for characteristic loads Lighting columns Part 3 1: Design and verification Specification for characteristic loads Lighting columns Part 3 2: Design and verification Verification by testing Lighting columns Part 3 2: Design and verification Verification by testing Period of validity: 08.09.2015 to 10.04.2019 Translation 32/52