Deburring & Edge Rounding Machines SIDEWINDER SERIES
SIDEWINDER DRY / WET SERIES DEBURRING & EDGE ROUNDING MACHINES Sidewinder Models SDi Single Disc and TBr Top Brush Series Multi-Directional Deburring and Edge Rounding Machines are ideal for sheet metal parts that need to be deburred or edge rounded to eliminate a sharp edge. The machines are most effective on parts fabricated on lasers, water jet cutters, shears, or punch presses. As a result of mounting the disc and/or brushes horizontally over the conveyor, the part is introduced in such a way that every edge, including holes and slots, are deburred and radiused using Scotch-Brite discs and proprietary top brushes. Made in USA. MODEL TBr DRY/WET SERIES The Sidewinder TBr Top Brush Series is designed for economically deburring and/or edge rounding a wide variety of ferrous and non-ferrous components. One or two head configurations are available where fewer passes are required to achieve the desired results. Simple to use. Easy to maintain. Made in USA. Control Panel STANDARD FEATURES Upper and lower frames manufactured from heavy-duty steel plate Conveyor bed is manufactured with 0.375 inch thick steel plate Conveyor bed machined to insure flatness Electric thickness adjustment Smooth top high coefficient of friction belt to hold small parts Automatic conveyor belt tracking system Pressure regulator for conveyor belt tracking Cartridge-style top brush head assembly(s): - Handwheel adjustment to maximize abrasive media wear - 10 inch diameter abrasive brushes or Scotch-Brite pads - Standard oscillating speed of 250 stokes per minute - Thickness pointer and scale Pinch rollers are spring-loaded Infeed conveyor section includes 2 vinyl covered rollers Electrical control panel with 24 volt DC circuit HMI/PLC controls with 5.7 inch color monitor Internal jog switch to facilitate setup Wet models include: - Stainless steel catch pan - Automatic parts dryer with Air Sonic air knife - Automatic paper bed filter Dry models include: - Conveyor belt cleaning - Dust collection pickups Infeed safety bar with over-thickness limit switch Exterior doors include safety interlocks UL/CSA approved components Emergency stop One & two head configurations MODEL TBr SPECIFICATIONS Maximum Panel Width Working Thickness - Minimum determined by material - Maximum 3D ENGINEERING DRAWING 37 INCH 36 inches (914 mm) 0.035 in (0.9 mm) 6 inches (152 mm) Minimum Part Length - w/top brush assemblies 12.5 inches (318 mm) Top Brush Head Assembly (TB) Brush/Pad Diameter Number of Brushes Brush Speed Motor Size (each) Oscillating Speed Pinch Roller Diameter Feed Speed Compressed Air Requirements Electrical Requirements 10 inches (254 mm) 4 each 1200 SFPM 2 HP 250 SPM 2.15 inches (55 mm) 6-40 FPM 80 PSI @ 5 CFM TBD ACCESSORIES Thin material hold-down shoe Vacuum bed with cleanout ports Top Brush Head (TB) Top Brushes Scotch-Brite Discs 4-10-inch diameter brushes or Scotch-Brite disc Top brushes are ideal for deburring and edge rounding materials greater than.050 thick Scotch-Brite discs are ideal for deburring and edge rounding materials less than.050 thick
SIDEWINDER SERIES MODEL SDi WET SERIES The Sidewinder SDi Single Disc Series is available in 18, 37, and 48-inch widths and is ideal for for deburring and removal of sharp edges on sheet metal parts processed on lasers, water jet cutters, shears or punch presses. A vacuum bed is included in the standard features allowing short parts to be run. As a result of mounting the disc horizontally over the conveyor, the part is introduced in such a way that every edge, including holes and slots, are deburred and radiused using a Scotch Brite disc. The SDi Series operates with coolant to maximize the life of the abrasive media, includes a paper bed filter. Made in USA. STANDARD FEATURES Heavy duty frame with heavy wall structural steel tubing and one (1) inch thick plate Constant pass line height Automatic, self-centering conveyor belt tracking system Smooth SBR rubber conveyor belt with vacuum hold-down Electronic variable speed AC drive with digital line speed display on control panel Electronic variable speed abrasive disc Note: SDi 48 abrasive disc oscillates for full part coverage Powered thickness adjustment with four (4) precision jacks guided on 1.5 inch gibs with digital display TEFC disc motor for head assembly with ammeter mounted on control panel Abrasive disc assembly is high speed balanced for precision operation Single infeed and outfeed pinch rollers Stainless steel drip pan & doors are corrosion resistant Automatic parts dryer with Air Sonic air knife and regenerative blower Automatic Paper Bed Filter with filter media, clean tank, sludge bin and clean return pump Central lubrication point Electric control panel with push button controls mounted on movable pendant arm Infeed end safety bar Safety interlocks and emergency stop UL/CSA Approved electric components Abrasive Disc Abrasive disc with variable speed controls for optimum results. OPTIONAL EQUIPMENT HMI/PLC controls with color monitor Small part return conveyor Note: maximum length, 14 inches Automatic Paper Bed Filter Includes filter media, clean tank, sludge bin, and clean return pump.
Sidewinder SDi Specifications Typical Application MODEL SDi SPECIFICATIONS Working width 18", 36" & 48" Working height 0-6" Minimum part length 6" Abrasive disc dimensions SDi 36/48 model 27" 48" Pinch roller diameter 2.25" Disc motor SDi 36 model SDi 48 model 5 hp Oscillating head drive motor Vacuum bed motor D18 model D36/48 model Air knife blower motor SDi 36 model SDi 48 model Conveyor motor Conveyor roller diameter Feed speed Height adjust motor 1 hp 25 hp 3 hp 4 hp 7.5 hp 2 hp 6" BEFORE 5-40 fpm 1 hp MACHINE CONFIGURATIONS SINGLE HEAD TBr TWO HEAD TBr SW SDi 18/36/48 DISC HEAD AFTER
YOUR REQUIREMENTS DRIVE OUR BUSINESS. Midwest Automation is a family owned U.S. manufacturing company located in Minneapolis Minnesota. For companies who care where the products they buy are made, it will come as no surprise that buying American is not as easy as it used to be. If you look closely you will discover that many of the machines represented to be American made are in fact imported from foreign countries. For over 60 years, Midwest Automation has manufactured industrial machinery for the woodworking, composite panel and metalworking industries using U.S. labor, and locally available components whenever possible. Our extensive application knowledge, coupled with creative machine designs, allows us to provide unique and reliable solutions that improve your manufacturing processes, supported by local parts and service. If you are looking for an industrial machinery manufacturer with real application expertise, contact Midwest Automation today. Manufacturing results since 1959. 2645 26th Avenue South, Minneapolis, MN 55406 phone 612-721-5347 www.midwestautomation.com 02.01.2017 Midwest Automation LLC