Floor Springs DORMA BTS 75 V BTS 80 BTS 84

Floor Springs DORMA BTS 75 V BTS 80 BTS 84

DORMA BTS 75 V DORMA BTS 80 DORMA BTS 84 Floor Springs Quality assurance for DORMA floor springs Quality assured manufacture to DIN ISO 900, EN 900, BS 5750. Certified and verified by BSI Quality Assurance Reg. No. Q 64, FM 0756 Data and features BTS75V BTS 80 BTS 84 ) For applications involving particularly high or heavy loads, and doors which have to close against wind or draught conditions, the next highest spring strength should be selected. ) For floor springs for fire and smoke check doors, see special brochure. Spring strength EN EN 4 EN 6 EN Spring strength adjustment EN -4 Standard and 950 mm external doors ) 00 mm 400 mm Fire and smoke check doors ) Non-handed, suitable for single and double action doors Closing speed adjustable by valve Backcheck, mechanical Hold-open, hydraulically adjustable Constant hold-open at 090 " " a door angle of 05 " " Delayed action adjustable by valve (selectable alternative to the hold-open feature) Weight in kg,0 7, 7, 7, 5,0 Dimensions in mm Length 85 4 4 4 06 Width 08 78 78 78 08 Height 050 60 60 60 040 Floor spring tested to EN 54 yes no " option BTS 75 V/80/84 GB

Floor spring With adjustable spring strength. Whether standard, narrow or wide, whether LH, RH or double action with the DORMA BTS 75 V, the right spring strength can be obtained by simply turning the integral adjustment screw. Designed and built DORMA BTS 75 V for robustness, the DORMA BTS 75 V is suitable for all doors up to a weight of 0 kg and a width up to 00 mm. Its range of functions ensures high user benefit, convenience and safety. 90 05 5 5 90 05 Fully controlled closing with adjustable speed in the ranges 75 5 and 5 0. Mechanical backcheck. Fixed hold-open at 90 or 05. Floor spring DORMA BTS 80 With many extras as standard. The DORMA BTS 80 is suitable for virtually any size and design of door and offers features which owe their effectiveness to extensive know-how in the development, design and manufacture of such units. Thanks to a wide range of functions which can be individually selected to suit different conditions and requirements, this floor spring offers maximum reliability and quality. 4 4 Fully controlled closing with adjustable speed. Hold-open range or delayed action range (approx. 75 to 80 ). Adjustment range point at which hold-open begins, or end of delayed action range (approx. 75 to 05 ). 4 Mechanical backcheck (from approx. 80 ). Floor spring DORMA BTS 84 The economical solution for double action doors. Specifically tailored to the requirements of floor springs for double action doors, the DORMA BTS 84 also impresses by its low-height design and the ease of installation that this brings. 4 With two closing ranges available for adjustment and the resulting flexibility of the floor spring s function, the BTS 84 is able to meet virtually any set of requirements. Its ever-constant reliability and functional efficiency are further enhanced by a comprehensive quality assurance programme. 4 First adjustable closing range (0 0 ). Second adjustable closing range (0 approx. 0 ). Fixed hold-open at 90 (optional extra). 4 Fixed hold-open at 05 (optional extra). BTS 75 V/80/84 GB

DORMA BTS 75 V Floor Spring DORMA BTS 75 V Specification text Universal floor spring with adjustable closing force, tested and approved to EN 54, size 4, corrosion class 4, non-handed unit suitable for LH, RH and double action doors, with closing action operational from approx. 75. Featuring hydraulically fully controlled closing cycle, adjustable closing speed with two independent valves, and mechanical backcheck. Cover plate secured to floor spring body. Special models ( Fixed hold-open at 90 ( Fixed hold-open at 05 Accessories ( Spindle ( standard (...mm extension ( special design... Adjusting screw for selecting the spring strength. Valve for closing speed adjustment, 75 5. Valve for closing speed adjustment, 75 5 Universal application... Selection of spindles available LH (ISO 6) RH (ISO 5) ( Universal cover plate,.5 mm thick ( stainless steel ( satin brass ( Sealing compound... for double action doors... for LH and RH single action doors Accessories Make DORMA BTS 75 V BTS75V BTS75V/90 BTS75V/05 Cover plate for double action doors Snap-off corner for LH (ISO 6) doors Snap-off corner for RH (ISO 5) doors Universal cover plate Adaptable to right or left hand single action applications by simply snapping off the appropriate pre-blanked corner sections. For centre pivoted (i.e. double action) doors, the corner sections remain in place. The universal cover plate is available in stainless steel or satin brass (material thickness.5 mm). DORMA 00 sealing compound For filling cavities between the floor spring body and the cement box to protect against moisture penetration (specified by German VOB regulations, inter alia, for wet rooms). 5 Spindles A range of interchangeable spindles is available to provide floor clearance in a variety of situations (doors with thresholds, carpeted floors etc). Special spindles available on application: e.g. with offset or square section; spindles for non-dormaspecific accessories are also available. Z Calculation of the requisite spindle extension = X floor clearance (standard value 8 mm) Check calculation: Collar height Z mm = spindle extension X Z 8 X Z 8 4 BTS 75 V/80/84 GB

DORMA BTS 80 Floor Spring DORMA BTS 80 Specification text Universal non-handed floor spring for single and double action doors up to max. 00 kg leaf weight. With closing action from approx. 75, hydraulically fully controlled, and with integral pressure compensation feature for multi-point holdopen between 75 and 80 (removable). With adjustable hold-open start point, delayed action (end of delayed action range adjustable between 75 and 05 ), and backcheck; including cement box and interchangeable spindle insert. Size ( EN ( EN 4 ( EN 6 60 Valve for adjustment of the closing speed Valve for activation of the hold-open or delayed action Adjusting screw for varying the start of the hold-open range or the end point of the delayed action range 6-4 6-4 Universal application... 78 4 5-57 Accessories ( Universal cover plate (.5 mm thick) ( stainless steel ( satin brass ( Extended spindle insert,... mm extension ( Sealing compound Make DORMA BTS 80... for double action doors... for LH and RH single action doors Accessories BTS80/ BTS80/4 BTS80/6 Cover plate for double action doors Snap-off corner for LH (ISO 6) doors Snap-off corner for RH (ISO 5) doors Universal cover plate Adaptable to right or left hand single action applications by simply snapping off the appropriate pre-blanked corner sections. For centre pivoted (i.e. double action) doors, the corner sections remain in place. The universal cover plate is available in stainless steel or satin brass (material thickness.5 mm). DORMA 00 sealing compound For filling cavities between the floor spring body and the cement box to protect against moisture penetration (specified by German VOB regulations, inter alia, for wet rooms). 5 Spindles A range of interchangeable spindles is available to provide floor clearance in a variety of situations (doors with thresholds, carpeted floors etc). Special spindles available on application: e.g. with offset or square section; spindles for non-dormaspecific accessories are also available. Z Calculation of the requisite spindle extension = X floor clearance (standard value 8 mm) Check calculation: Collar height Z mm = spindle extension X Z 8 X Z 8 BTS 75 V/80/84 GB 5

DORMA BTS 84 Floor Spring DORMA BTS 84 Specification text Floor spring for double action doors, with hydraulically fully controlled closing from approx. 0, tested to EN 54; including cement box and replaceable spindle insert. Size ( EN Models ( Standard model ( With fixed hold-open at 90 ( With fixed hold-open at 05 Accessories ( Cover plate ( stainless steel ( satin brass ( Extended spindle insert,... mm extension ( Sealing compound Valve for adjusting the closing speed in the range 0 to 0 Valve for increasing the closing speed in the range 0 0 Accessories Make DORMA BTS 84 BTS84/ 6 4 Z 0 0,5 Cover plate available in stainless steel or satin brass. 5 Calculation of the requisite spindle extension = X floor clearance (standard value 8 mm) Check calculation: Collar height Z mm = spindle extension DORMA 00 sealing compound For filling cavities between the floor spring body and the cement box to protect against moisture penetration (specified by German VOB regulations, inter alia, for wet rooms). X Z 8 Spindles A range of interchangeable spindles is available to provide floor clearance in a variety of situations (doors with thresholds, carpeted floors etc). Special spindles available on application: e.g. with offset or square section; spindles for non-dormaspecific accessories are also available. 6 BTS 75 V/80/84 GB

DORMA BTS 75 V DORMA BTS 80 DORMA BTS 84 Floor Springs Equipment and accessories Floor spring Floor spring Extended interchangeable spindles* (extension in mm) Universal cover plate Sealing including including 0 5 7.5 0.5 5 0 5 8 0 5 40 45 50 compound cement box cement box Stainless Satin 00 and standard without steel brass 0.5 kg spindle spindle 45090059 BTS 80 BTS 75 V EN EN 800000 80000 EN 4 EN 4 800000 80000 EN 6 EN 6 800000 80000 BTS 84 450040 standard 450040 Size EN 4 67000 # # # # # # # # # # # # # # Size EN 4 with hold-open at 90 # # # # # # # # # # # # # # # # # 6700 46700059 4670059 Size EN 4 with hold-open at 05 # # # # # # # # # # # # # # 6700 # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # 46700000 4670000 # # # # # # # # # # # # # # EN # # # # # # # # # # # # # # 8000 8000 with hold-open at 90 EN # # # # # # # # # # # # # # 8000 8000 450040 4500404 450049 4500405 4500406 4500407 450044 4500408 4500409 450040 45004 45004 # # # 467000 467000 # = Optional accessory *Special models on application: e.g. with offset or square section insert; spindles for non-dorma-specific accessories also available BTS 75 V/80/84 GB 7

Accessories for floor springs Aluminium-framed single action doors For aluminium-framed single action doors Aluminium door straps for flush-closing single action doors of various systems door widths up to 00 mm, leaf weights up to 0 kg non-handed easy to install no cutting work required; just four drill holes fast fixing thanks to lock pin connections robust and secure connection with insert plate and reinforcing bracket the press-fitted steel insert provides a robust, load-bearing interference fit with the floor spring s spindle Example installation DORMA aluminium hinge, 6 mm, and DORMA aluminium door strap for DORMA BTS floor spring (alternative: DORMA floor pivot bearing). DORMA aluminium door straps Art. No. 7459 Silver finish (EV, Euras C-0): Order No. 4500409 Dark brown finish (DB 4, Euras C-4): Order No. 4500709 Special colours on application. DORMA aluminium door straps Art. No. 7459 B Silver finish (EV, Euras C-0): Order No. 450048 Dark brown finish (DB 4, Euras C-4): Order No. 450078 Special colours on application. ( ) = Dimensions for model 7459 B 8 BTS 75 V/80/84 GB

Drilling template for aluminium hinges For standard hinges (9 mm dia.), for insulated door hinges ( mm dia.) and also for and -part hinges; indicate dimensions x and y, or profile system. Drilling templates Universal drilling template for aluminium door straps Art. No. 7459 L Adjustable to different profile systems; for standard doors (9 mm dia.) and insulated doors, external fixing ( mm dia.). Standard model: Order No. 45090074 Type B model: Order No. 45090075 Universal drilling template for LM door straps for direct screw fixing Art. No. 7459 L/D Adjustable to different profile systems, designed for direct fixing; for standard doors (9 mm dia.) and insulated doors, external fixing ( mm dia.). Standard model: Order No. 45090077 Type B model: Order No. 45090078 Heavy duty door straps Art. No. 7456/ Drop-forged steel; adjustable to different profile systems, non-handed. Order No. 4500006 Drop-forged steel door strap Covers See pages 0 and, Art. No. 808/ and 748/. BTS 75 V/80/84 GB 9

Accessories for floor springs Single action timber doors For flush-closing single action timber doors Top centre Art. No. 74 K/56 Steel, zinc-plated; with eccentric pin and eccentric plastic bushing for adjusting the door once installed (adjustment range ± mm); non-handed. Order No. 450006 56 6 56 6 8 Door strap Art. No. 74/56 Drop-forged steel, zinc-plated. Order No. 450000 Washer cover for door strap Art. No. 74 of stainless steel. Order No. 4509000 Covers for top centre and for door strap Design Order No. for covers For top centre, For door strap, two-part single part LH door (ISO 6) RH door (ISO 5) Die-cast aluminium Art. No. 748/748 Suitable for anodising 455000 4505500 450500 Silver (EV, Euras C-0) 4550040 45055400 4505400 Dark brown (DB 4, Euras C-4) 4550070 45055700 4505700 Aluminium hinges with fixings for flush-closing timber doors Offset in mm Art. No. 6 A-6.0 A-.0 A-.0 0 BTS 75 V/80/84 GB

For over-rebated single action timber doors Top centre Art. No. 74 K/46 Steel, zinc-plated; with eccentric pin and eccentric plastic bushing for adjusting the door once installed (adjustment range ± mm). LH door (ISO 6) Order No. 450505 RH door (ISO 5) Order No. 45005 Door strap Art. No. 74/46 Drop-forged steel, zinc-plated. Order No. 4500000 Washer cover for door strap Art. No. 74 of stainless steel. Order No. 4509000 Covers for top centre and for door strap Design Order No. for covers For top centre, For door strap, two-part single part LH door (ISO 6) RH door (ISO 5) LH door (ISO 6) RH door (ISO 5) Die-cast aluminium Art. No. 7484/748 Suitable for anodising 4550500 455000 450550 45050 Silver (EV, Euras C-0) 45505400 4550400 4505540 450540 Dark brown (DB 4, Euras C-4) 45505700 4550700 4505570 450570 Aluminium hinges with fixings for over-rebated timber doors For order numbers, see separate aluminium hinges brochure Drilling template for flush-closing and over-rebated doors Dimension x = 50.5 mm Dimension y = mm BTS 75 V/80/84 GB

Accessories for floor springs Single action steel doors For single action steel doors Weld-on Top centre Art. No. 74 K Steel, primer-coated; with eccentric pin and eccentric plastic bushing for adjusting the door once installed (adjustment range ± mm); non-handed. Order No. 45000 Door strap Art. No. 74 Drop-forged steel, primer-coated. Order No. 4500005 Washer cover for door strap Art. No. 74 of stainless steel. Order No. 4509000 Weld-in Top centre Art. No. 744 K Steel, primer-coated; with eccentric pin and eccentric plastic bushing for adjusting the door once installed (adjustment range ± mm); non-handed. Order No. 450004 Door strap Art. No. 744 Drop-forged steel, primer-coated. Order No. 4500007 Covers See pages 0 and Art. No. 808/ and 748/ Weld-on extension Art. No. 74 Order No. 450900 ( ) = TS 9 5 7 BTS 75 V/80/84 GB

DORMA accessories Pivot bearings Pivot bearings Floor pivot Floor pivot Art. No. 747 K ) with ball bearing assembly, load capacity max. 00 kg. Order No. 4507000 Cover plate 747 K/AX Art. No. 747 AX with angular-contact ball bearing, load capacity max. 00 kg. Order No. 4507000 Floor pivot Floor pivot Art. No. 7475 AX with angular-contact ball bearing, load capacity max. 00 kg. Order No. 4507000 Also available in stainless steel. Art. No 8560 GE. Order No. 65540059 Weld-on pivot bearing Weld-on pivot bearing Art. No. 747 K with ball bearing, load capacity max. 00 kg, and door strap 74 (see page ); can be used for LH and RH doors by reversing connection. Order No. 4507000 Weld-on hinge Weld-on hinge Art. No. 747 M for use as centre and top hinge; with eccentric pin and eccentric plastic bushing for adjusting the door once installed (adjustment range ± mm); can be used for LH and RH doors by reversing connection. Order No. 45900008 Weld-on pivot bearing Weld-on pivot bearing Art. No. 7474 K ) with ball bearing, load capacity max. 00 kg, and welded reinforcement plate. LH (ISO 6) door: Order No. 45075007 RH (ISO 5) door: Order No. 4507007 AX model available on request ) Also available with extended spindles, extensions in increments of 5 mm up to a maximum length of 50 mm. Screw-on pivot bearing Screw-on pivot bearing Art. No. 747 K ) with ball bearing, load capacity max. 00 kg, and reinforcing plate supplied as loose part. Suitable for timber, steel and aluminium doors. LH (ISO 6) door: Order No. 45075005 RH (ISO 5) door: Order No. 4507005 Screw-on pivot bearing Art. No. 7476 AX with angular-contact ball bearing, load capacity max. 00 kg Order No. 450700 BTS 75 V/80/84 GB

Accessories for floor springs Double action doors For steel, aluminium and timber double action doors Adjustable top centre (complete) Art. No. 806 in die-cast aluminium Order No. 460000 Art. No. 8066 in steel Order No. 4600004 comprising upper section with adjustable pin for bridging door-frame gaps up to 0 mm, and lower section with needle bearing. Flat design ensures no routing or milling of the basic frame profile necessary. For bridging of larger doorframe gaps, a top centre with 0 mm or 0 mm extended pin is also available. Cover plate Art. No. 8064 Order No. for stainless steel 4600044 Order No. EV (C-0) 460050 in stainless steel, bright aluminium and EV (Euras C-0) Upper section 806/8067 Cover plate 8064 Lower section 806 Lower section 8067 Order No. 46000 Screw-on angle bracket 8065 Order No. 460009 Adjustable top centre comprising an upper section with adjustable pin for bridging door-frame gaps up to max. 0 mm, and a lower section (A or B) for special door constructions. A top centre upper section with a 0 mm or 0 mm extended pin is available for bridging larger door-frame gaps. Upper section 8066/746* Cover plate 8064 Lower section 8066 Lower section 746 A Order No. 4600004 * For lower sections 746 A and 746 B, use upper section 746 with mm dia. pin, Order No. 460006. Lower section 746 B Order No. 4600049 4 BTS 75 V/80/84 GB

Example installations for aluminium doors Top centre 806 Door straps Universal door strap Art. No. 74 Drop-forged steel, zinc-plated; adjustable to different profile systems. Order No. 460000 X = min. 5 mm for steel doors Top centre 8067 Door strap Art. No. 80 Zinc-plated steel; for leaf weights up to 00 kg. Order No. 450040 X = min. 5 mm Door strap Art. No. 74 Drop-forged steel, zinc-plated. Order No. 460000 for timber doors Top centre 8066 Door strap installation examples X = min. 5 mm for steel doors Top centre 746 Door strap 80 Door strap 74 Door strap 74 with milled recess without milled recess X = min. 5 mm Door strap 74 Door strap 80 Door strap 74 BTS 75 V/80/84 GB 5

DORMA GmbH + Co. KG Postfach 40 09 D-5847 Ennepetal Tel. +49(0)/79-0 Fax +49(0)/79 4 95 www.dorma.com Subject to change without notice WN 05 XXX, XX/0, GB, XX. XX/CtP, XX/0

Transom concealed door closer DORMA RTS 85

DORMA RTS 85 Transom concealed door closer Disappears into the frame Ideal for shopfitting. For both double and single action doors. Elegant, versatile, practical and quality assured. The DORMA RTS 85 offers a solution for installations where door control must be provided without disturbing the aesthetic appearance of the door. The majority of preparation can be accomplished by the fabricator prior to installation, Plus points For the trade Just one body for all types of fixing. Low inventory costs and minimal stocking requirement thanks to unit packs for closer body and accessories. For the fabricator Can be used for double action doors, or left and right hand single action doors. Installation and setting adjustment possible before fixing the doorset on site. No floor preparation necessary. Positive zero position for double action doors easy to adjust. Comprehensive range of accessories. leaving minimal on-site work. A complete line of accessories is available to accommodate virtually any door and frame configuration. Quality assured manufacture to DIN ISO 900, EN 900, BS 5750 certified and verified by BSI Quality Assurance Reg.-No. Q 64, FM 0756 For the architect/specifier Aesthetically impressive solution especially with toughened glass doors. Ideal for shopfitting applications. For the user No cluttering of door or floor appearance. Backcheck to prevent door contact with the frame. Smooth closing with adjustable closing speed. Technical Data RTS 85 Closing force EN EN 4 EN 5 Internal up to 950 mm doors* 00 mm 50 mm External up to 950 mm doors* 00 mm 050 mm Same model for double action doors, RH (ISO 5) and LH (ISO 6) Closing speed variable by valve adjustment Final closing speed variable by valve adjustment Backcheck, progressive, mechanical Backstop, mechanical Hold-open 05 " " " 90 " " " Extended spindle 005 mm " " " 00 mm " " " Reduced pivot point for tempered glass doors (65 mm) " " " Weight in kg 4.7 4.8 4.9 Dimensions in mm Length Width 90 90 90 Height 8 8 8 Door closer tested to EN 54 Yes No " Option * Max Door weight for floor pivot 8550 8557 90 kgs. 8560 G 00 kgs. 5 4 5 4 Standard and optional functions Fully controlled closing with adjustable speed Adjustable final closing Progressive mechanical backcheck 4 Mechanical backstop** 5 Hold-open points depending on model (optional) 05 or 90 ** Door opening angle max. 0 on both sides; in the case of heavy doors which can be opened further, door stops must be used. In the case of single action doors, the opening angle may be reduced depending on the door design. RTS 85, GB

DORMA RTS 85 Accessories Accessories for double action and centre pivoted single action doors (70 mm pivot point) Side-load installation Side-load installation is achieved by offering the door in the closed position, onto the floor pivot. The closer arm, fitted in the upper door rail, is connected to the spindle and secured with a clamping piece. Floor pivot set, total height 57 mm Art.-No. 855 for bottom rails with channel depth of 8 50 mm. (Floor portion may be shortened to suit bottom rail.) Floor portion of pivot is fitted directly to floor. Closer arm with arm channel Art.-No. 850 for top rails with min. 5 mm channel depth and 8 mm width. Closer arm with angle bracket Art.-No. 85 for top rails with min. mm channel depth and 8 mm width (not suitable for doors with mitred-joints). Floor pivot set, total height 7 mm Art.-No. 8550 for bottom rails with channel depth of 8 0 mm. Floor portion of pivot is fitted directly to floor. 4 Threshold pivot set Art.-No. 8554 for bottom rails with channel depth of 5 mm. Floor clearance: 5 mm. Floor portion is fitted directly to threshold. (Upper portion same as ). Threshold pivot set Art.-No. 8556 for bottom rails with channel depth of 40 mm. Floor clearance: 5 mm. Floor portion is fitted directly to threshold. (Upper portion same as ). 4 End-load installation End-load installation is achieved by offering the door, in the open position, onto the floor pivot and spindle simultaneously. The floor pivot locks automatically, connection to spindle is secured with a clamping piece. Closer arm with arm channel Art.-No. 854 for top rails with min. mm channel depth and 5 mm width. Closer arm with angle bracket Art.-No. 855 for top rails with min. 8 mm channel depth and 5 mm width (not suitable for doors with mitred-joints). Floor pivot set, total height 7 mm Art.-No. 855 for bottom rails with channel depth of 8 0 mm. Floor portion of pivot is fitted directly to floor. Floor pivot set, total height 57 mm Art.-No. 855 for bottom rails with channel depth of 8 50 mm. (Floor portion may be cut to suit bottom rail). Floor portion is fitted directly to floor. 4 Threshold pivot set Art.-No. 8555 for bottom rails with channel depth of 5 mm. Floor clearance: 5 mm. Floor portion is fitted directly to threshold. (Upper portion same as ). 4 RTS 85, GB

Accessories for butt hung or offset pivoted single action doors Single action doors hung on butt hinges or offset pivots can be connected to the closer with slide arm and channel assemblies. Please note that this application may reduce the maximum opening angle available on the door. Similarly, if a hold-open model has been selected, the hold-open point will be altered: eg instead of 05, the position will lie between 90 and 00, depending on door thickness. Note: Maximum door opening with slide arm and channel assemblies 05. Consult our Technical Service Department giving specific details for slide arm and channel assemblies. Drawings of door and frame details must be submitted together with the pivot centre of the hinge. Slide arm and channel Art.-No. 850 Weld-on extension Art.-No. 85 For steel doors, 40 mm long (can be shortened), 8 mm dia. Einklappseite 95 breit Accessories for tempered glass doors (65 mm pivot point) For tempered glass doors, the RTS 85 is used with a special fixing bracket, Art.-No. 850 G, giving a 65 mm pivot point. The standard patch fittings can thus be used with appropriate inserts. (Patch fittings with insert available from DORMA-Glas range of products). Fixing bracket Art.-No. 850 G For fixing the DORMA RTS in the transom. Floor pivot bearing with flat-tapered spindle Art.-No. 8560 G With sealed roller bearing assembly, rust-protected, for max. door weights of 0 kg (if used without the transom concealed door closer, then 00 kg). Special pivots also available with extended spindles of 5, 0 and 5 mm, and also for special environments (e.g. wet rooms) in stainless steel; Art.-No. 8560 GE (only available with standard spindle). The floor pivot bearing combined with appropriate bottom straps from the accessories range for DORMA BTS floor springs is also suitable for aluminium, steel and timber doors. RTS 85, GB 4

Einklappseite 95 breit Typical applications Double action aluminium door Single action timber door Double action tempered glass door with aluminium frame Single action double rebated aluminium door Single action timber door in a steel frame Detailed installation drawings on a scale of : will be provided on request. RTS 85, GB 5

DORMA RTS 85 Transom concealed door closer DORMA RTS 85 for double and single action doors Door closer Standard Standard Standard with spindle with spindle with spindle with spindle with spindle with spindle RTS 85 model model with model with insert 5 mm insert 5 mm insert 5 mm insert 0 mm insert 0 mm insert 0 mm hold-open hold-open extended extended and extended and extended extended and extended and at 05 at 90 hold-open hold-open hold-open hold-open at 05 at 90 at 05 at 90 EN 850 850 850 850 850 850 850 850 850 EN 4 850 850 850 850 850 850 850 850 850 EN 5 850 850 850 850 850 850 850 850 850 Accessories closer arm closer arm Floor pivot Floor pivot Threshold Threshold Closer arm weld-on with with set, set, pivot set pivot set with channel extensions channel bracket height height HH 9 /6HH for single 7 mm 57 mm action doors Side-load installation 850005 850007 65000 654000 6550400 6550500 85000 85000 End-load installation 850009 8500 65000 654000 6550400 DORMA RTS 85 for tempered glass doors Door closer Standard Standard Standard with spindle with spindle with spindle with spindle with spindle with spindle RTS 85 G model model with model with insert 5 mm insert 5 mm insert 5 mm insert 0 mm insert 0 mm insert 0 mm hold-open hold-open extended extended and extended and extended extended and extended and at 05 90 hold-open hold-open hold-open hold-open at 05 at 90 at 05 at 90 EN 850 850 850 850 850 850 850 850 850 EN 4 850 850 850 850 850 850 850 850 850 EN 5 850 850 850 850 850 850 850 850 850 Accessories Floor pivot Floor pivot Floor pivot Floor pivot Floor pivot set set 5 mm set 0 mm set 5 mm set stainless extended extended extended steel to RTS 85 G 65540000 85005 85006 85007 85540059 Specification text Transom concealed door closer with built-in cushion backcheck, adjustable closing speed and sweep range. Size Y EN Y EN 4 Y EN 5 DORMA GmbH + Co. KG Division Door Control www.dorma.com Australia DORMA Door Controls Pty. Ltd. P.O. Box 09 Narre Warren Vic 805 5 Abbott Road Hallam/Victoria 80 Australia Phone: +6 /97 96 5 55 Fax: +6 /97 96 9 55 Central Europe DORMA GmbH + Co. KG Postfach 40 09 D-5847 Ennepetal Phone: +49 /79-0 Fax: +49 /79495 Emerging Markets DORMA GmbH + Co. KG Postfach 40 09 D-5847 Ennepetal Phone: +49 /7 9-0 Fax: +49 /79495 Model Y For both single and double action doors (pivot point 70 mm) Y For tempered glass doors (pivot point 65 mm) Y Non hold-open Y Hold-open at 05 Far East DORMA Door Controls Pte. Ltd. No. Jalan Terusan, Jurong Singapore 6985 Phone: +65 668/76 Fax: +65 665/7995 France DORMA France S.A.R.L. Silic 56 0/, Rue du Morvan F-946 Rungis-Cedex Phone: + /45 08 08 Fax: + /45 08 8 Gulf DORMA Gulf Door Controls FZE Jebel Ali Free Zone, Roundabout 8 Unit VC 0, P.O. Box 768 Jebel Ali Dubai, United Arab Emirates Phone: +97 48/8 90 4 Fax: +97 48/8 90 5 DORMA Group North America DORMA Door Controls DORMA Drive Reamstown, Pa. 7567, U.S.A. Phone: +77/ 6 8 8 Fax: +77/ 6 06 Y Hold-open at 90 Y With spindle insert 5 mm extended Y With spindle insert 0 mm extended Y Closer arm Art.-No. ScanBalt DORMA Danmark A/S Sindalvej 6 8 DK-60 Rødovre Phone: +45 44/94 0 77 Fax: +45 44/94 95 04 South Africa DORMA Door Controls (Pty.) Ltd. Kings Court 4A Mineral Crescent ZA-000 Crown/Gauteng Johannesburg Phone: +7 /8 0 0 80 Fax: +7 /8 0 0 9 South America DORMA Sistemas de Controles para Portas Ltda. Av. Piracema, 400 Centro Empresarial Tambore CEP 06400 Barueri/ São Paulo, Brasil Phone: +55 /4 9 8 Fax: +55 /4 9 8 Y Floor pivot set Art.-No. Make: DORMA RTS 85 South-East Europe DORMA AUSTRIA GmbH Pebering Strass A-50 Eugendorf Phone: +4 6 5/ 84 88 Fax: +4 6 5/ 84 9 South Europe DORMA Italiana S.r.l. Via. A. Canova 44/46 I-005 Lissone (MI) Phone: +9 09/4 40 Fax: +9 09/4 40 0 DORMA Ibérica, S.A. Camino San Martín de la Vega, 4 E-8500 Arganda del Rey (Madrid) Phone: +4 9/8 75 78 50 Fax: +4 9/8 75 78 8 UK/Ireland DORMA Door Controls Ltd. DORMA Trading Park Staffa Road GB-London E0 7QX Phone: +44 08/5 58 84 Fax: +44 08/5 58 6 WN 050 97 55, 07/0, RTS 85, GB, x. xx/ctp. 06/06 Subject to change without notice