FITTINGS
Push - in fittings 431 Series Fluid... Working pressure... Vacuum level... Rated temperature... Torque... Standards... Materials... Compressed air Max. 20 bar (290 psi) 55 mm Hg vacuum (99 %) -20...80 C (-4...16 F) - Consult for temperatures higher than +80 C M5 1/8 1/4 3/8 1/2 1,6Nm 8Nm 12Nm 30Nm 35Nm DIN 3852, NF E49051, NF E48051 and JIS B2351 HR polymer (high chemical and impact resistant), brass collet gripping, stainless steel gripping washer (Ø8, 10 and 12 mm), NBR seals, nickel plated brass housing. All models are sillicon-free guaranted Instant Connection This technology allows easy and instant connection by hand, without the use of tools. Installation. Simply push the tubing until it can go no further. Connection and sealing is accomplished instantaneously.. To disconnect, push on the release button and pull out the tube.. To achieve a 90 straight cut of the tube, use the MICRO tube cutter. Advantages. Instantaneous connection and disconnection.. Full flow (no restriction to passage) as gripping and sealing is achieved using the outside diameter of the tube without deformation.. Immediate sealing by means of the O-ring seal and the optimised design of the tube.. Space saving installation: no access required for a tightening tool. Characteristics - For pneumatic installations - High Resistance Polymer - Designed for use with plastic tubing (PA, Polyurethane) - Light weight, compact and aesthetic Male stud fittings Male stud elbow ØG ØG M 5 4 0.431.010.419 M 5 6 0.431.010.619 G 1/8 4 0.431.010.410 G 1/8 6 0.431.010.610 G 1/8 8 0.431.010.810 G 1/4 4 0.431.010.413 G 1/4 6 0.431.010.613 G 1/4 8 0.431.010.813 G 1/4 10 0.431.011.013 G 3/8 8 0.431.010.81 G 3/8 10 0.431.011.01 G 3/8 12 0.431.011.21 G 1/2 12 0.431.011.221 G 1/2 14 0.431.011.421 M 5 4 0.431.990.419 M 5 6 0.431.990.619 G 1/8 4 0.431.990.410 G 1/8 6 0.431.990.610 G 1/8 8 0.431.990.810 G 1/4 4 0.431.990.413 G 1/4 6 0.431.990.613 G 1/4 8 0.431.990.813 G 1/4 10 0.431.991.013 G 3/8 8 0.431.990.81 G 3/8 10 0.431.991.01 G 3/8 12 0.431.991.21 G 1/2 12 0.431.991.221 G 1/2 14 0.431.991.421.1.1.1
Push - in fittings 431 Series Oscillating compact elbow (0...20 ) Equal elbow ØG M 5 4 0.431.890.419 G 1/8 4 0.431.890.410 G 1/8 6 0.431.890.610 G 1/4 8 0.431.890.813 G 1/4 10 0.431.891.013 G 3/8 10 0.431.891.01 G 3/8 12 0.431.891.21 4 0.431.020.400 6 0.431.020.600 8 0.431.020.800 10 0.431.021.000 12 0.431.021.200 14 0.431.021.400 Male stud branch Tee Equal Tee ØG M 5 4 0.431.980.419 M 5 6 0.431.980.619 G 1/8 4 0.431.980.410 G 1/8 6 0.431.980.610 G 1/8 8 0.431.980.810 G 1/4 4 0.431.980.413 G 1/4 6 0.431.980.613 G 1/4 8 0.431.980.813 G 1/4 10 0.431.981.013 G 3/8 8 0.431.980.81 G 3/8 10 0.431.981.01 G 3/8 12 0.431.981.21 G 1/2 12 0.431.981.221 G 1/2 14 0.431.981.421 4 0.431.040.400 6 0.431.040.600 8 0.431.040.800 10 0.431.041.000 12 0.431.041.200 14 0.431.041.400 Single Y piece Unequal multiple Y piece 2 x 1 1 x 2 4 4 0.431.400.400 6 8 0.431.400.608 4 x 1 1 x 2 4 6 0.431.440.406.1.1.2
Push - in fittings 431 Series Plug-in single Y piece Plug-in multiple Y piece 2 x 1 1 x 2 4 4 0.431.420.400 4 6 0.431.420.406 4 x Ø D1 1 x Ø D2 4 6 0.431.430.406 4 8 0.431.430.408 Male stud elbow (45 ) Multiple Tee, with fixing holes ØG 1 2 M 5 4 0.431.330.419 M 5 6 0.431.330.619 G 1/8 4 0.431.330.410 G 1/8 6 0.431.330.610 G 1/8 8 0.431.330.810 G 1/4 6 0.431.330.613 G 1/4 8 0.431.330.813 G 1/4 10 0.431.331.013 G 3/8 8 0.431.330.81 G 3/8 1 0.431.331.01 G 3/8 12 0.431.331.21 G 1/2 12 0.431.331.221 6 4 0.433.040.604 8 4 0.433.040.804 8 6 0.433.040.806 10 6 0.433.041.006 10 8 0.433.041.008 Equal cross Unequal cross 3 x 1 1 x 2 4 0.431.00.400 6 0.431.00.600 8 0.431.00.800 4 6 0.431.00.604 6 8 0.431.00.806.1.1.3
Push - in fittings 431 Series Tube / tube connector Double male stem connector 4 0.431.060.400 6 0.431.060.600 8 0.431.060.800 10 0.431.061.000 12 0.431.061.200 14 0.431.061.400 4 0.431.200.400 6 0.431.200.600 8 0.431.200.800 10 0.431.201.000 12 0.431.201.200 Reducer Increaser 1 2 1 2 4 6 0.431.660.406 4 8 0.431.660.408 4 10 0.431.660.410 6 8 0.431.660.608 6 10 0.431.660.610 6 12 0.431.660.612 8 10 0.431.660.810 8 12 0.431.660.812 10 12 0.431.661.012 12 14 0.431.661.214 6 4 0.431.680.604 Bulkhead connector Blanking plugs 4 0.431.160.400 6 0.431.160.600 8 0.431.160.800 10 0.431.161.000 12 0.431.161.200 4 0.431.260.400 6 0.431.260.600 8 0.431.260.800 10 0.431.261.000 12 0.431.261.200 14 0.431.261.400.1.1.4
Push-in fittings 441 and 451 Series Type... Fluid... Working pressure... Max. inlet pressure... Rated temperature... Vacuum level... Connection threads... Torque (kgf.cm)... Materials... Push-in fittings, 441 series (G thread) and 451 series (BSPT thread) Compressed air - Water 0...10 bar (0...145 psi) 15 bar (21 psi) -20...80 C (-4...16 F) - 1 bar (-14,5 psi) Cylindrical (G) or tapered (BSPT) M5 1/8 1/4 3/8 1/2 15-19 0-90 120-140 220-240 280-300 Nickel plated brass and PBT resin bodies, stainless steel gripping washer, NBR seals, PTFE coating (in tapered threads) Male stud fittings (G thread) ØR x1 x10 x50 x100 M 3 4 0.451.010.409 0.451.010.409/010 0.451.010.409/050 0.451.010.409/100 M 5 4 0.451.010.419 0.451.010.419/010 0.451.010.419/050 0.451.010.419/100 M 5 6 0.451.010.619 0.451.010.619/010 0.451.010.619/050 0.451.010.619/100 G 1/8 4 0.441.010.410 0.441.010.410/010 0.441.010.410/050 0.441.010.410/100 G 1/8 6 0.441.010.610 0.441.010.610/010 0.441.010.610/050 0.441.010.610/100 G 1/8 8 0.441.010.810 0.441.010.810/010 0.441.010.810/050 0.441.010.810/100 G 1/4 4 0.441.010.413 0.441.010.413/010 0.441.010.413/050 0.441.010.413/100 G 1/4 6 0.441.010.613 0.441.010.613/010 0.441.010.613/050 0.441.010.613/100 G 1/4 8 0.441.010.813 0.441.010.813/010 0.441.010.813/050 0.441.010.813/100 G 1/4 10 0.441.011.013 0.441.011.013/010 0.441.011.013/050 0.441.011.013/100 G 1/4 12 0.441.011.213 0.441.011.213/010 0.441.011.213/050 0.441.011.213/100 G 3/8 8 0.441.010.81 0.441.010.81/010 0.441.010.81/050 0.441.010.81/100 G 3/8 10 0.441.011.01 0.441.011.01/010 0.441.011.01/050 0.441.011.01/100 G 3/8 12 0.441.011.21 0.441.011.21/010 0.441.011.21/050 0.441.011.21/100 G 1/2 12 0.441.011.221 0.441.011.221/010 0.441.011.221/050 0.441.011.221/100 G 1/2 16 0.441.011.621 0.441.011.621/010 0.441.011.621/050 0.441.011.621/100 Male stud elbow (G thread) ØR x1 x10 x50 x100 M 3 4 0.451.990.409 0.451.990.409/010 0.451.990.409/050 0.451.990.409/100 M 5 4 0.451.990.419 0.451.990.419/010 0.451.990.419/050 0.451.990.419/100 M 5 6 0.451.990.619 0.451.990.619/010 0.451.990.619/050 0.451.990.619/100 G 1/8 4 0.441.990.410 0.441.990.410/010 0.441.990.410/050 0.441.990.410/100 G 1/8 6 0.441.990.610 0.441.990.610/010 0.441.990.610/050 0.441.990.610/100 G 1/8 8 0.441.990.810 0.441.990.810/010 0.441.990.810/050 0.441.990.810/100 G 1/4 4 0.441.990.413 0.441.990.413/010 0.441.990.413/050 0.441.990.413/100 G 1/4 6 0.441.990.613 0.441.990.613/010 0.441.990.613/050 0.441.990.613/100 G 1/4 8 0.441.990.813 0.441.990.813/010 0.441.990.813/050 0.441.990.813/100 G 1/4 10 0.441.991.013 0.441.991.013/010 0.441.991.013/050 0.441.991.013/100 G 3/8 8 0.441.990.81 0.441.990.81/010 0.441.990.81/050 0.441.990.81/100 G 3/8 10 0.441.991.01 0.441.991.01/010 0.441.991.01/050 0.441.991.01/100 G 3/8 12 0.441.991.21 0.441.991.21/010 0.441.991.21/050 0.441.991.21/100 G 1/2 12 0.441.991.221 0.441.991.221/010 0.441.991.221/050 0.441.991.221/100 G 1/2 16 0.441.991.621 0.441.991.621/010 0.441.991.621/050 0.441.991.621/100.1.1.10
Push-in fittings 441 and 451 Series Male stud branch Tee (G thread) ØR x1 x10 x50 x100 M 5 4 0.451.980.419 0.451.980.419/010 0.451.980.419/050 0.451.980.419/100 M 5 6 0.451.980.619 0.451.980.619/010 0.451.980.619/050 0.451.980.619/100 G 1/8 4 0.441.980.410 0.441.980.410/010 0.441.980.410/050 0.441.980.410/100 G 1/8 6 0.441.980.610 0.441.980.610/010 0.441.980.610/050 0.441.980.610/100 G 1/8 8 0.441.980.810 0.441.980.810/010 0.441.980.810/050 0.441.980.810/100 G 1/4 4 0.441.980.413 0.441.980.413/010 0.441.980.413/050 0.441.980.413/100 G 1/4 6 0.441.980.613 0.441.980.613/010 0.441.980.613/050 0.441.980.613/100 G 1/4 8 0.441.980.813 0.441.980.813/010 0.441.980.813/050 0.441.980.813/100 G 1/4 10 0.441.981.013 0.441.981.013/010 0.441.981.013/050 0.441.981.013/100 G 3/8 8 0.441.980.81 0.441.980.81/010 0.441.980.81/050 0.441.980.81/100 G 3/8 10 0.441.981.01 0.441.981.01/010 0.441.981.01/050 0.441.981.01/100 G 3/8 12 0.441.981.21 0.441.981.21/010 0.441.981.21/050 0.441.981.21/100 G 1/2 12 0.441.981.221 0.441.981.221/010 0.441.981.221/050 0.441.981.221/100 Male stud fittings (BSPT thread) ØR x1 x10 x50 x100 R 1/8 4 0.451.010.410 0.451.010.410/010 0.451.010.410/050 0.451.010.410/100 R 1/8 6 0.451.010.610 0.451.010.610/010 0.451.010.610/050 0.451.010.610/100 R 1/8 8 0.451.010.810 0.451.010.810/010 0.451.010.810/050 0.451.010.810/100 R 1/4 4 0.451.010.413 0.451.010.413/010 0.451.010.413/050 0.451.010.413/100 R 1/4 6 0.451.010.613 0.451.010.613/010 0.451.010.613/050 0.451.010.613/100 R 1/4 8 0.451.010.813 0.451.010.813/010 0.451.010.813/050 0.451.010.813/100 R 1/4 10 0.451.011.013 0.451.011.013/010 0.451.011.013/050 0.451.011.013/100 R 3/8 8 0.451.010.81 0.451.010.81/010 0.451.010.81/050 0.451.010.81/100 R 3/8 10 0.451.011.01 0.451.011.01/010 0.451.011.01/050 0.451.011.01/100 R 3/8 12 0.451.011.21 0.451.011.21/010 0.451.011.21/050 0.451.011.21/100 R 1/2 12 0.451.011.221 0.451.011.221/010 0.451.011.221/050 0.451.011.221/100 Male stud elbow (BSPT thread) ØR x1 x10 x50 x100 R 1/8 4 0.451.990.410 0.451.990.410/010 0.451.990.410/050 0.451.990.410/100 R 1/8 6 0.451.990.610 0.451.990.610/010 0.451.990.610/050 0.451.990.610/100 R 1/8 8 0.451.990.810 0.451.990.810/010 0.451.990.810/050 0.451.990.810/100 R 1/4 4 0.451.990.413 0.451.990.413/010 0.451.990.413/050 0.451.990.413/100 R 1/4 6 0.451.990.613 0.451.990.613/010 0.451.990.613/050 0.451.990.613/100 R 1/4 8 0.451.990.813 0.451.990.813/010 0.451.990.813/050 0.451.990.813/100 R 1/4 10 0.451.991.013 0.451.991.013/010 0.451.991.013/050 0.451.991.013/100 R 3/8 8 0.451.990.81 0.451.990.81/010 0.451.990.81/050 0.451.990.81/100 R 3/8 10 0.451.991.01 0.451.991.01/010 0.451.991.01/050 0.451.991.01/100 R 3/8 12 0.451.991.21 0.451.991.21/010 0.451.991.21/050 0.451.991.21/100 R 1/2 12 0.451.991.221 0.451.991.221/010 0.451.991.221/050 0.451.991.221/100 Male stud branch Tee (BSPT thread) ØR x1 x10 x50 x100 R 1/8 4 0.451.980.410 0.451.980.410/010 0.451.980.410/050 0.451.980.410/100 R 1/8 6 0.451.980.610 0.451.980.610/010 0.451.980.610/050 0.451.980.610/100 R 1/8 8 0.451.980.810 0.451.980.810/010 0.451.980.810/050 0.451.980.810/100 R 1/4 6 0.451.980.613 0.451.980.613/010 0.451.980.613/050 0.451.980.613/100 R 1/4 8 0.451.980.813 0.451.980.813/010 0.451.980.813/050 0.451.980.813/100 R 1/4 10 0.451.981.013 0.451.981.013/010 0.451.981.013/050 0.451.981.013/100 R 3/8 8 0.451.980.81 0.451.980.81/010 0.451.980.81/050 0.451.980.81/100 R 3/8 10 0.451.981.01 0.451.981.01/010 0.451.981.01/050 0.451.981.01/100 R 3/8 12 0.451.981.21 0.451.981.21/010 0.451.981.21/050 0.451.981.21/100.1.1.11
Push-in fittings 441 and 451 Series Tube / tube connector x1 x10 x50 x100 4 0.451.060.400 0.451.060.400/010 0.451.060.400/050 0.451.060.400/100 6 0.451.060.600 0.451.060.600/010 0.451.060.600/050 0.451.060.600/100 8 0.451.060.800 0.451.060.800/010 0.451.060.800/050 0.451.060.800/100 10 0.451.061.000 0.451.061.000/010 0.451.061.000/050 0.451.061.000/100 12 0.451.061.200 0.451.061.200/010 0.451.061.200/050 0.451.061.200/100 Equal elbow x1 x10 x50 x100 4 0.451.020.400 0.451.020.400/010 0.451.020.400/050 0.451.020.400/100 6 0.451.020.600 0.451.020.600/010 0.451.020.600/050 0.451.020.600/100 8 0.451.020.800 0.451.020.800/010 0.451.020.800/050 0.451.020.800/100 10 0.451.021.000 0.451.021.000/010 0.451.021.000/050 0.451.021.000/100 12 0.451.021.200 0.451.021.200/010 0.451.021.200/050 0.451.021.200/100 Equal Tee x1 x10 x50 x100 4 0.451.040.400 0.451.040.400/010 0.451.040.400/050 0.451.040.400/100 6 0.451.040.600 0.451.040.600/010 0.451.040.600/050 0.451.040.600/100 8 0.451.040.800 0.451.040.800/010 0.451.040.800/050 0.451.040.800/100 10 0.451.041.000 0.451.041.000/010 0.451.041.000/050 0.451.041.000/100 12 0.451.041.200 0.451.041.200/010 0.451.041.200/050 0.451.041.200/100 Reducer 1 2 x1 x10 4 6 0.451.660.406 0.451.660.406/010 4 8 0.451.660.408 0.451.660.408/010 6 8 0.451.660.608 0.451.660.608/010 6 10 0.451.660.610 0.451.660.610/010 6 12 0.451.660.612 0.451.660.612/010 8 10 0.451.660.810 0.451.660.810/010 8 12 0.451.660.812 0.451.660.812/010 10 12 0.451.661.012 0.451.661.012/010.1.1.12
Push-in fittings 441 and 451 Series Male stud elbow 45 (G thread) ØR x1 x10 G 1/8 4 0.441.330.410 0.441.330.410/010 G 1/8 6 0.441.330.610 0.441.330.610/010 G 1/4 6 0.441.330.613 0.441.330.613/010 G 1/8 8 0.441.330.810 0.441.330.810/010 G 1/4 8 0.441.330.813 0.441.330.813/010 G 1/4 10 0.441.331.013 0.441.331.013/010 G 3/8 10 0.441.331.01 0.441.331.01/010 G 3/8 12 0.441.331.21 0.441.331.21/010 G 1/2 12 0.441.331.221 0.441.331.221/010 Universal elbow (G thread) A female thread equal to the male thread is located in the upper side. ØR x1 x10 G 1/8 4 0.441.240.410 0.441.240.410/010 G 1/8 6 0.441.240.610 0.441.240.610/010 G 1/4 6 0.441.240.613 0.441.240.613/010 G 1/4 8 0.441.240.813 0.441.240.813/010 G 3/8 8 0.441.240.81 0.441.240.81/010 G 3/8 10 0.441.241.01 0.441.241.01/010 G 1/2 10 0.441.241.021 0.441.241.021/010 G 1/2 12 0.441.241.221 0.441.241.221/010 Equal cross x1 x10 4 0.451.00.400 0.451.00.400/010 6 0.451.00.600 0.451.00.600/010 8 0.451.00.800 0.451.00.800/010 Double male stem connector x1 x10 4 0.451.200.400 0.451.200.400/010 6 0.451.200.600 0.451.200.600/010 8 0.451.200.800 0.451.200.800/010 10 0.451.201.000 0.451.201.000/010 12 0.451.201.200 0.451.201.200/010.1.1.13
Push-in fittings 441 and 451 Series Female Y connector (3 female ports) 1 (1x) 2 (2x) x1 x10 4 4 0.451.400.400 0.451.400.400/010 6 6 0.451.400.600 0.451.400.600/010 8 6 0.451.400.608 0.451.400.608/010 8 8 0.451.400.800 0.451.400.800/010 10 10 0.451.401.000 0.451.401.000/010 Plug-in Y connector (2 female, 1 male ports) 1 (1x) 2 (2x) x1 x10 4 4 0.451.420.400 0.451.420.400/010 6 4 0.451.420.406 0.451.420.406/010 Multiple Tee connector 1 (2x) 2 (3x) x1 x10 6 4 0.453.040.604 0.453.040.604/010 8 4 0.453.040.804 0.453.040.804/010 8 6 0.453.040.806 0.453.040.806/010 10 6 0.453.041.006 0.453.041.006/010 10 8 0.453.041.008 0.453.041.008/010 Bulkhead connector M x1 x10 4 M12 0.451.160.400 0.451.160.400/010 6 M14 0.451.160.600 0.451.160.600/010 8 M16 0.451.160.800 0.451.160.800/010 10 M20 0.451.161.000 0.451.161.000/010 12 M22 0.451.161.200 0.451.161.200/010.1.1.14
Push-in fittings 441 and 451 Series Non-return valve x1 x10 4 0.451.260.400 0.451.260.400/010 6 0.451.260.600 0.451.260.600/010 8 0.451.260.800 0.451.260.800/010 10 0.451.261.000 0.451.261.000/010 12 0.451.261.200 0.451.261.200/010.1.1.15
Connection accessories Accessories Reducer male to female Straight male adaptor ØC 1 ØC 2 ØC 1 ØC 2 Double female sleeve G 1/8 M5 0.401.681.019 G 1/4 M5 0.401.681.319 G 1/4 G 1/8 0.401.681.310 G 3/8 G 1/8 0.401.681.10 G 3/8 G 1/4 0.401.681.13 G 1/2 G 1/4 0.401.682.113 G 1/2 G 3/8 0.401.682.11 G 3/4 G 1/4 0.401.682.13 G 3/4 G 3/8 0.401.682.1 G 3/4 G 1/2 0.401.682.21 G 1/8 M5 0.000.008.901 G 1/8 G 1/8 0.000.008.902 G 1/4 G 1/8 0.000.008.903 G 1/4 G 1/4 0.000.008.904 G 3/8 G 1/8 0.000.008.905 G 3/8 G 1/4 0.000.008.906 G 3/8 G 3/8 0.000.008.90 G 1/2 G 1/2 0.000.008.908 G 3/4 G 1/2 0.000.008.909 G 3/4 G 3/4 0.000.008.910 Internal hexagon headed plug ØC ØC M5 0.000.008.911 G 1/8 0.000.008.912 G 1/4 0.000.008.913 G 3/8 0.000.008.914 G 1/2 0.000.008.915 G 3/4 0.000.008.916 M5 0.000.008.621 G 1/8 0.000.005.424 G 1/4 0.000.005.840 G 3/8 0.000.005.841 G 1/2 0.000.005.842 G 3/4 0.000.008.422 Manifold block (Cross) Manifold block (bar) Teflon tape 4 x ØC M5 0.000.008.929 G 1/8 0.000.008.930 G 1/4 0.000.008.931 G 3/8 0.000.008.932 G 1/2 0.000.008.933 G 3/4 0.000.008.934 2 x ØC 1 8 x ØC 2 G 1/4 M5 0.000.008.935 G 3/8 G 1/8 0.000.008.936 G 1/2 G 1/4 0.000.008.93 G 3/4 G 1/2 0.000.008.938 Length Wide 10 m 12, mm 0.403.000.029.2.1.1
Tubes and hoses Standard tubing Polyurethane tubing (PU) The excellent flexibility of polyurethane tubing allows compact cabling where a small bend radius is required. According to NF E49-101 standard. The range comprises polyester polyurethane tubing, for superior chemical resistance and improved ageing, - High flexibility and small bend radius - Large range of working temperatures and pressures - Good chemical resistance (ask for list of fluids) - Small pressure drop - Constant rigidity, good ageing - Good absorption of vibration - UV resistant - 5 colours for easy circuit identification (mm) i (mm) Blue Red Green Yellow Black 4 2,5 0.000.012.528 0.403.000.110 0.403.000.111 0.403.000.112 0.403.000.113 6 4 0.000.012.529 0.403.000.114 0.403.000.115 0.403.000.116 0.403.000.11 8 5,5 0.000.012.530 0.403.000.118 0.403.000.119 0.403.000.120 0.403.000.121 10 0.000.012.531 0.403.000.122 0.403.000.123 0.403.000.124 0.403.000.125 12 8 0.000.012.532 0.403.000.126 0.403.000.12 0.403.000.128 0.403.000.129 14 9,5 0.000.026.226 16 12 0.900.004.800 Nylon tubing (PA12) Nylon tubing provides optimum mechanical properties, has good chemical resistance and conforms to NF E49-100 standard. (mm) i (mm) Natural Color - Large range of working temperatures and pressures - Good chemical resistance (ask for list of fluids) - Good humidity resistance - Small pressure drop - Constant rigidity, good ageing with constant tolerance on O.D. - Good absorption of vibration - Strong abrasion resistance 4 2, 0.000.008.616 6 4 0.000.008.61 8 6 0.000.008.618 10 8 0.000.008.619 12 10 0.000.008.620 14 11 0.000.01.315.5.1.2