BEARINGS INTRODUCTION General Information The Uses and Limitations of This Manual This publication is a compilation of material from the Manufacturers whose products we are proud to distribute throughout Australia. The material has been selected to make it easy for bearings to be identified, so a replacement can be ordered, confident that the right bearing is being fitted and will give satisfactory service. While containing some technical information, this Manual is primarily for the identification of a replacement and not for selecting a bearing by load carrying capacity. There could, however, be occasions when the information contained in the Manual will prompt a question as to whether by selecting another type or size of bearing there would be a more satisfactory performance of the equipment into which the bearing is to be fitted. On these occasions would welcome your inquiry so we can provide expert advice. Before replacing a failed bearing it is a wise practice to consider if the failure appears premature. If it seems likely that this could be the case it may be worthwhile to refer to the Bearing Engineering Section of this manual showing various bearing failures and their likely causes. After all, there is little point in spending the money to carry out the replacement if the cause of the premature failure is not removed and rectified. The two common causes for bearing failure are lack of cleanliness and the fit of the bearing on the shaft and/or in the housing not being correct. They may well have been correct once upon a time - but what about now! That is why we have included tables which show some basic recommended tolerances in the Bearing Engineering Section of this Manual for the most important detail effecting bearing performance. If you are designing some new equipment and need to make an initial selection, please contact your nearest branch for assistance. When Should a Bearing Be Replaced? The usual signs that there is a troublesome bearing will be one or all of the following:- Rough running of the equipment effecting its performance Significant increase in the bearing temperature Abnormal noise from the bearing housing These conditions will prompt the scheduling of the equipment for inspection. After dismantling the equipment and identifying the problem, it is strongly recommended that even if the other bearing(s) on the same shaft as the failed bearing appears to be okay, it, too, should be replaced. In the long run this will prove to be an economically sound policy. Some may be cautious about that recommendation as well as the proposition that if a machine is being overhauled for reasons other than the bearings that, nonetheless, all the bearings are replaced. The reasons for these recommendations are:- The other bearing(s) on a shaft with a failed bearing have almost certainly been subjected to abnormal loading resulting from the rough running of that failed bearing which will cause it to fail at some time before the new bearing now being fitted. The same reasoning applies to a machine overhaul. In both cases, the following points are worth considering:- The cost of bearings is very small, relative to the cost of the loss of machine availability and its effect on production. There is no additional labour costs to fit new bearings while the machine is being reassembled. Stripping down a machine for major overhaul is frequently carried out in less than ideally clean conditions which makes it likely that rubbish will find its way into those parts of the bearing which are difficult to clean out and almost impossible to inspect, particularly Double Row Bearings - both ball and spherical roller. Even a single row tapered roller bearing is not really easy to clean thoroughly. When dismantling equipment, it is difficult to avoid the risk of bruising the tracks of ball bearings and scoring the tracks of roller bearings. In fact, some machine designs are such that to take them apart is almost impossible to avoid. Damage to bearings will probably not become obvious until the machine goes back into service - with frustrations to all concerned when it has to be returned to the workshop to be reworked. GENERAL INFORMATION 1
BEARINGS Rolling Bearings : Structures and Types General Information STRUCTURE Rolling bearings (bearings hereinafter) normally comprise bearing rings, rolling elements and a cage. (see Fig. 1-1). Rolling elements are arranged between inner and outer rings with a cage, which retains the rolling elements in correct relative position, so they do not touch one another. With this structure, a smooth rolling motion is realized during operation. 2) Rolling element Rolling elements may be either balls or rollers. Many types of bearings with various shapes of rollers are available. Bearings are classified by the number of rows of rolling elements: e.g. single-row, double-row, or multi-row (triple or four-row) bearings. Fig. 1-1: Bearing Structure Deep Groove Ball Bearing Outer ring Ball Inner ring Cage Tapered Roller Bearing Cup Roller Cone Cage 3) Cage The cage guides the rolling elements along the bearing rings, retaining the rolling elements in correct relative position. There are various materials and types of cages including pressed, machined, moulded, and pin type cages in Steel, Brass and Plastics. Due to lower friction resistance than that found in full complement roller and ball bearings, bearings with a cage are more suitable for use under high speed rotation. TYPE 1) Bearing Rings Thrust Ball Bearing Shaft washer Ball Housing Cage Note: In thrust bearings inner and outer rings are also called shaft washer and housing washer, respectively; in tapered roller bearings, the respective forms are cone and cup. The path of the rolling elements is called the raceway; and, the section of the bearing rings where the elements roll is called the raceway surface. In the case of ball bearings, since grooves are provided for the balls, they are also referred to as raceway grooves. The contact angle (α) is the angle formed by the direction of the load applied to the bearing rings and rolling elements, and a plan perpendicular to the shaft center, when the bearing is loaded. Bearings are classified into two types in accordance with the contact angle (α). Radial bearings (0 < α < 45 ) - designed to accommodate mainly radial load. Thrust bearings (45 < α < 90 ) - designed to accommodate mainly axial load. Rolling bearings are classified in Fig. 1-2, and characteristics of each bearing type are described in Tables 1-1 to 1-13. The inner ring is normally engaged with a shaft; and, the outer ring with a housing. 2
BEARINGS General Information Rolling Bearing Structures and Types Fig. 1-2: Rolling Bearing Structures and Types 6210 4210 7210 3210 QJ 1210 N210 NNU NCS RNA 30210 TDI 22210 3
BEARINGS AUTOMOBILE Bearings Classified by Use General Information Bearings Classification RAILWAY ROLLING STOCK ELECTRIC EQUIPMENT BUSINESS EQUIPMENT STEEL INDUSTRY EQUIPMENT PAPER MANUFACTURING EQUIPMENT AIRCRAFT Others P210 FL210 F210 T210 SD510 SN510 4
BEARINGS Table 1-1: Deep Groove Ball Bearings General Information Deep Groove Ball Bearings Maximum capacity type VV (2RU) DDU (2RS) BL (M) 680, 690, 600, 620, 630, (ML), (OB)...Extra-small, miniature bearing 6800, 6900, 16000, 6000, 6200, 6300, 6400 The most popular types among rolling bearings, widely used in a variety of industries. Radial load and axial load in both directions can be accommodated. Suitable for operation at high speed, with low noise and low vibration. Sealed bearings employing steel shields or rubber seals are filled with the appropriate volume of grease when manufactured. Bearings with a flange or locating snap ring attached on the outer ring are easily mounted in housings for simple positioning of housing location. In spite of having the same boundary dimensions as standard bearings, maximum type bearings have a higher load rating because a filling slot on each of the inner and outer rings, allows a greater number of balls to be inserted than do standard bearings. Recommended Cages BL200 BL300 4200 4300 Pressed steel cage (ribbon type, snap type), copper alloy or phenolic resin machined cage, synthetic resin moulded cage. Main Applications Automobile: Front and rear wheels, transmissions, electric devices. Electric Equipment: Standard motors, electric appliances for domestic use. Others: Measuring instruments, internal combustion engines, construction equipment, railway rolling stock, cargo transport equipment, agricultural equipment, equipment for other industrial uses. 5
BEARINGS Table 1-2: Angular Contact Ball Bearings General Information Angular Contact Ball Bearings 7000, 7200, 7300, 7400... Contact Angle 30 7000B, 7200B, 7300B, 7400B... 40 7900C, 7000C, 7200C, 7300C... 15 3200 3300 Contact Angle 32 5200 5300 Contact Angle 24 Bearing rings and balls possess their own contact angle which is normally 15, 30, or 40. (Larger contact angle... higher resistance against axial load) (Smaller contact angle...more advantageous for high-speed rotation) Single-row bearings can accommodate radial load and axial load in one direction. DB and DF matched pair bearings and double-row bearings can accommodate radial load and axial load in both directions. DT matched pair bearing are used for applications where axial load in one direction is too large for one bearing to accept. Angular contact ball bearings are used for high accuracy and high-speed operation. Axial load in both directions and radial load can be accommodated by adapting a structure pairing two single-row angular contact ball bearings back to back. For bearings with no filling slot, the sealed type is available. Recommended cages Pressed steel cage (Conical type...single-row: S Type, Snap Type...double-row), copper alloy or phenolic resin machined cage, synthetic resin moulded cage. Main applications Single-row: Machine tool spindles, high frequency motors, gas turbines, centrifugal separators, front wheels of small size automobiles, differential pinion shafts Double-row: Hydraulic pumps, roots blowers, air-compressors, transmissions, fuel injection pumps, printing equipment 6
BEARINGS Table 1-3: Four Point Contact Ball Bearings (QJ) Table 1-4: General Information Four Point Contact & Self-Aligning Self-Aligning Ball Bearings Two-piece inner ring Cylindrical Bore Tapered Bore Sealed QJ200 QJ300 Radial load and axial load in both directions can be accommodated. A four-point contact ball bearing can substitute for a faceto-face or back-to-back arrangement of angular contact ball bearings. Suitable for use under pure axial load or combined radial and axial load with heavy axial load. This type of bearing possesses a contact angle (a) determined in accordance with the axial load direction. This means that the bearing ring and balls contact each other at two points on the lines forming the contact angle. Recommended cage Copper alloy machined cage Main applications Aircraft jet engines, gas turbines 120, 130 1200, 1300 2200, 2300 Spherical outer ring raceway allows self-alignment, accommodating shaft or housing deflection and misaligned mounting conditions. Tapered bore design can be mounted readily using an adaptor. Pressed steel cage 2200 2RS 2300 2RS (Staggered type 12, 13, 22...2RS, 23...2RS) (Snap type 22, 23) Power transmission shaft of wood working and spinning machines, plummer blocks. 7
BEARINGS Table 1-5: Cylindrical Roller Bearings General Information Cylindrical Roller Bearings NU1000, NU200, NU300, NU400 NU2200, NU2300 NU3200, NU3300 Cylindrical Bore NNU4900 NN3000 Tapered Bore NNU4900K NN3000K Cylindrical Bore Tapered Bore RV RVK Since the design allowing linear contact of cylindrical rollers with the raceway provides strong resistance to radial load, this type is suitable for use under heavy radial load and impact load, as well as at high speed. N and NU types are ideal for use on the free side. They are movable in the shaft direction in response to changes in bearing position relative to the shaft or housing, which are caused by heat expansion of the shaft or improper mounting. NJ and NF types can accommodate axial load in one direction; and NH and NUP types can accommodate partial axial load in both directions. With separable inner and outer ring, this type ensures easy mounting. Due to their high rigidity, NNU and NN types are widely used in machine tool spindles. Recommended cages Pressed steel cage, copper alloy machined cage, pin type cage, synthetic resin moulded cage Main applications Large and medium size motors, traction motors, generators, internal combustion engines, gas turbines, machine tool spindles, speed reducers, cargo transport equipment, and other industrial equipment 8
BEARINGS General Information Needle Roller Bearings Table 1-6: Machined Ring Needle Roller Bearings With inner ring Without inner ring Sealed With inner ring Without inner ring NA4800 NA4900 NA5900 RNA4800 RNA4900 RNA5900 -- NA4900UU -- NA6900 RNA6900 In spite of their basic structure, which is the same as that of NU type cylindrical roller bearings, bearings with minimum ring sections offer space savings and greater resistance to radial load, by using needle rollers. Bearings with no inner rings function using heat treated and ground shafts as their raceway surface. Recommended cage Pressed steel cage Main applications Automobile engines, transmissions, pumps, power shovel wheel drums, hoists, overhead travelling cranes, compressors. Reference: Many needle roller bearings other than those with machined ring are available. For further details, refer to the section, Needle Roller Bearing Specification Table. 9
BEARINGS Table 1-7: Tapered Roller Bearings General Information Tapered Roller Bearings Standard Intermediate Steep Contact Angle Contact Contact Angle Angle 32900J 30200J 30200C 30300DJ 32000J 32200J 32200C 31300J 33000J 33200J 30300C 33100J 30300J 32300C 32300J KBE KDE Tapered rollers assembled in the bearings are guided by the cone back face rib. The raceway surfaces of cone and cup and the rolling contact surface of rollers are designed so that the respective apexes converge at a point on the bearing center line. Single-row bearings can accommodate radial load and axial load in one direction, and double-row bearings can accommodate radial load and axial load in both directions. This type of bearing is suitable for use under heavy load or impact load. Bearings are classified into standard, intermediate and steep types, in accordance with their contact angle (a). The larger the contact angle is, the greater the bearing resistance to axial load. KH KDH KV KVE KVS Since cup and cone assembly can be separated from each other, mounting is easy. Bearings designated by the suffix J are interchangeable internationally. Items sized in inches are still widely used. Recommended cages Pressed steel cage, synthetic resin moulded cage, pin type cage. Main applications Automobile: Front and rear wheels, transmissions, differential pinion. Others: Machine tool spindles, construction equipment, large size agricultural equipment, railway rolling stock speed reduction gears, rolling mill roll necks and speed reducers, etc 10
BEARINGS Table 1-8: Spherical Roller Bearings General Information Spherical Roller Bearings NSK M C, CD & EA CAM H K or K30 Torrington SD CJ YM CF K or K30 SKF -- CC CA -- K or K30 Fag MB -- EAM ETVPB K or K30 KOYO R RH RHA SR K or K30 23900, 23000, 23100, 22200, 21300 24000, 24100, 23200, 22300 Spherical roller bearings comprising barrel-shaped convex rollers, double-row inner ring and outer ring are classified into types according to their internal structure. With the bearing designed such that the circular arc center of the outer ring raceway matches with the bearing center, the bearing is self-aligning, insensitive to errors of alignment of the shaft relative to the housing, and to shaft bending. This type can accommodate radial load and axial load in both directions, which makes it especially suitable for applications in which heavy load or impact load is applied. The tapered bore type can be easily mounted/dismounted by using an adapter or withdrawal sleeve. There are two types of tapered bores (tapered ratio): 1 : 30 supplementary... Suitable for 1 : 12 [ ] code K30 series 240 and 241 supplementary... Suitable for series code K other than 240 & 241 [ ] Lubrication holes, a lubrication groove and anti-rotation pin hole can be provided on the outer ring. Lubrication holes and a lubrication groove can be provided on the inner ring, too. Recommended cages Copper alloy machined cage, pressed steel cage, pin type cage, synthetic resin moulded cage. Main applications Paper manufacturing equipment, speed reducers, railway rolling stock axle journals, rolling mill pinion stands, table rollers, crushers, shaker screens, printing equipment, wood working equipment, speed reducers for various industrial uses, plummer blocks. 11
BEARINGS Table 1-9: Thrust Ball Bearings General Information Thrust Ball Bearings 51100 51200 51300 51400-53200 53300 53400-53200U 53300U 53400U - 52200 52300 52400-54200 54300 54400-53200U 54300U 54400U This type of bearing comprises washer-shaped rings with raceway groove and ball and cage assembly. Washers to be mounted on shafts are called shaft washers (or inner rings); and, washers to be mounted into housings are housing washers (or outer rings). Central washers of double direction bearings are mounted on the shafts. Single direction bearings accommodate axial load in one direction, and double direction bearings accommodate axial load in both directions. (Both of these bearings cannot accommodate radial loads). Since bearings with a spherical back face are self-aligning, it helps to compensate for mounting errors. Recommended Cages Pressed steel cage, copper alloy or phenolic resin machined cage, synthetic resin moulded cage Main Applications Automobile king pins, machine tool spindles 12
BEARINGS Table 1-10: Cylindrical Roller Thrust Bearings Table 1-11: General Information Roller Thrust Bearings Needle Roller Thrust Bearings SINGLE DIRECTION SEPARABLE NON-SEPARABLE TMP This type of bearing comprises washer-shaped rings (shaft and housing washer) and cylindrical roller and cage assembly. Crowned cylindrical rollers produce uniform pressure distribution on roller/raceway contact surface. Axial load can be accommodated in one direction. Great axial load resistance and high axial rigidity are provided. Recommended cages Copper alloy machined cage. Main applications Oil excavators, iron and steel equipment. The separable type, comprising needle roller and cage thrust assembly and a washer, can be matched with a pressed thin washer or machined thick washer. The non-separable type comprises needle roller and cage thrust assembly and a precision pressed washer. Axial load can be accommodated in one direction. Due to the very small installation space required, this type contributes greatly to size reduction of application equipment. In many cases, needle roller and cage thrust assembly function by using the mounting surface of the application equipment, including shafts and housings, as its raceway surface. Recommended cages Pressed steel cage, synthetic resin moulded cage. Main applications Transmissions for automobiles, cultivators and machine tools. 13
BEARINGS Table 1-12: Tapered Roller Thrust Bearings General Information Roller Thrust Bearings Table 1-13: Spherical Roller Thrust Bearings T THR 2THR 29200 29300 29400 This type of bearing comprises tapered rollers (with spherical large end), which are uniformly guided by the ribs of the shaft and housing washers. Both shaft and housing washers and rollers have tapered surfaces whose apexes converge at a point on the bearing axis. Single direction bearings can accommodate axial load in one direction; and, double direction bearings can accommodate axial load in both directions. Double direction bearings are to be mounted such that their central washer is placed on the shaft shoulder. Since this type is treated with a clearance fit, the central washer must be fixed with a sleeve, etc This type of bearing, comprising barrel-shaped convex rollers arranged at an angle with the axis, is self-aligning due to spherical housing washer raceway; therefore, shaft inclination can be compensated for to a certain degree. Great axial load resistance is provided. This type can accommodate a small amount of radial load as well as heavy axial load. Normally, oil lubrication is employed. Recommended cages Copper alloy machined cage Recommended cages Copper alloy machined cage Main applications Single direction: Crane hooks, oil excavator swivels Double direction: Rolling mill roll necks Main applications Hydroelectric generators, vertical motors, propeller shafts for ships, screw down speed reducers, jib cranes, coal mills, crushing machines, moulding machines 14
Ball Bearings Single Row - Radial... 16 Metric... 16 Inch... 19 Single Row - Maximum Capacity... 21 Spherical OD & Wide Series... 22 Extra Small & Miniature... 23 Single Row - Angular Contact... 26 Single Row - Duplex (QJ)... 29 Single Row - Magneto... 30 Thrust - Single Direction... 31 Metric... 31 Inch... 33 Thrust - Double Direction... 35 Double Row - Self Aligning... 36 Metric... 36 Inch... 38 Double Row - Radial... 39 Double Row - Angular Contact... 40 Triangle s Lazy Susan... 41 Sprag Clutches... 42 NSK One-Way Clutches... 43 15
BALL BEARINGS Single Row - Radial Metric Dimensions Bearing Variance ID OD W Number ZZ VV DDU NR ZNR 3 10 4 623 13 5 633 4 12 4 604 13 5 624 16 5 634 5 14 5 605 16 5 625 19 6 635 6 17 6 606 19 6 626 22 7 636 7 19 6 607 22 7 627 26 9 637 8 22 7 608 24 8 628 28 9 638 9 24 7 609 26 8 629 30 10 639 10 19 5 6800 22 6 6900 26 8 6000 28 8 16100 30 9 6200 35 11 6300 12 21 5 6801 24 6 6901 28 7 16001 28 8 6001 30 8 16101 32 10 6201 37 12 6301 13 32 10 6201-13ZZ 15 24 5 6802 28 7 6902 32 8 16002 32 9 6002 35 11 6202 37 9 98202 42 13 6302 16 35 11 6202-16DDU (contact seal type) 40 12 6203-16DDU (contact seal type) 17 26 5 6803 30 7 6903 35 8 16003 35 10 6003 40 12 6203 47 14 6303 62 17 6403 Dimensions in mm. 16 ZZ VV DDU NR ZNR Dimensions Bearing Variance ID OD W Number ZZ VV DDU NR ZNR 20 32 7 6804 37 9 6904 42 8 16004 42 9 98204 42 12 6004 47 14 6204 52 10 98304 52 15 6304 72 19 6404 22 44 12 60/22 50 14 62/22 56 16 63/22 25 37 7 6805 42 9 6905 47 8 16005 47 12 6005 52 9 98205 52 15 6205 62 12 98305 62 17 6305 80 21 6405 28 52 12 60/28 58 16 62/28 68 18 63/28 30 42 7 6806 47 9 6906 55 9 16006 55 13 6006 62 10 98206 62 16 6206 72 19 6306 90 23 6406 32 58 13 60/32 65 17 62/32 INTERCHANGE TABLE NSK ZZ VV DDU NR ZNR KOYO ZZ 2RU 2RS NR ZNR NTN ZZ LLB LLU NR ZNR SKF 2Z 2RZ 2RS1 NR ZNR FAG 2ZR - 2RSR NR ZRN* NACHI ZZE 2NKE 2NSE NR ZENR TO 75MM NACHI 75MM AND OVER ZZ 2NK 2NSL NR ZNR * Does not include Snap Ring For more information on miniature bearings, please refer to the Extra Small & Miniature section.
BALL BEARINGS Single Row - Radial Metric Dimensions Bearing Variance ID OD W Number ZZ VV DDU NR ZNR 32 75 20 63/32 35 47 7 6807 55 10 6907 62 9 16007 62 14 6007 70 10 98207 72 17 6207 80 21 6307 100 25 6407 40 52 7 6808 62 12 6908 68 9 16008 68 15 6008 80 11 98208 80 18 6208 90 23 6308 110 27 6408 45 58 7 6809 68 12 6909 75 10 16009 75 16 6009 85 11 98209 85 19 6209 100 17 98309 100 25 6309 120 29 6409 50 65 7 6810 72 12 6910 80 10 16010 80 16 6010 90 11 98210 90 20 6210 110 27 6310 130 31 6410 55 72 9 6811 80 13 6911 90 11 16011 90 18 6011 100 21 6211 120 29 6311 140 33 6411 60 78 10 6812 85 13 6912 95 11 16012 95 18 6012 105 12 98212 110 22 6212 130 31 6312 150 35 6412 65 85 10 6813 Dimensions in mm. ZZ VV DDU NR ZNR Dimensions Bearing Variance ID OD W Number ZZ VV DDU NR ZNR 65 90 13 6913 100 11 16013 100 18 6013 120 23 6213 140 33 6313 160 37 6413 70 90 10 6814 100 16 6914 110 13 16014 110 20 6014 125 24 6214 147 24 98314 150 35 6314 180 42 6414 75 95 10 6815 105 16 6915 115 13 16015 115 20 6015 130 25 6215 160 37 6315 190 45 6415 80 100 10 6816 110 16 6916 125 14 16016 125 22 6016 140 26 6216 170 39 6316 200 48 6416 85 110 13 6817 120 18 6917 130 14 16017 130 22 6017 150 28 6217 180 41 6317 210 52 6417 90 115 13 6818 INTERCHANGE TABLE NSK ZZ VV DDU NR ZNR KOYO ZZ 2RU 2RS NR ZNR NTN ZZ LLB LLU NR ZNR SKF 2Z 2RZ 2RS1 NR ZNR FAG 2ZR - 2RSR NR ZRN* NACHI ZZE 2NKE 2NSE NR ZENR TO 75MM NACHI 75MM AND OVER ZZ 2NK 2NSL NR ZNR * Does not include Snap Ring If the product you need is not listed, please contact your local branch. 17
BALL BEARINGS Single Row - Radial Metric Dimensions Bearing Variance ID OD W Number ZZ VV DDU NR ZNR 90 125 18 6918 140 16 16018 140 24 6018 160 30 6218 190 43 6318 225 54 6418 95 120 13 6819 130 18 6919 145 16 16019 145 24 6019 170 32 6219 200 45 6319 100 125 13 6820 140 20 6920 150 16 16020 150 24 6020 180 34 6220 215 47 6320 250 58 6420 105 130 13 6821 145 20 6921 160 18 16021 160 26 6021 190 36 6221 225 49 6321 110 140 16 6822 150 20 6922 170 19 16022 170 28 6022 200 38 6222 240 50 6322 120 150 16 6824 165 22 6924 180 19 16024 180 28 6024 215 40 6224 260 55 6324 130 165 18 6826 180 24 6926 200 22 16026 200 33 6026 230 40 6226 280 58 6326 140 175 18 6828 190 24 6928 210 22 16028 210 33 6028 250 42 6228 300 62 6328 150 190 20 6830 Dimensions in mm. 18 ZZ VV DDU NR ZNR Dimensions Bearing Variance ID OD W Number ZZ VV DDU NR ZNR 150 210 28 6930 225 24 16030 225 35 6030 270 45 6230 320 65 6330 160 200 20 6832 220 28 6932 240 25 16032 240 38 6032 290 48 6232 340 68 6332 170 215 22 6834 230 28 6934 260 28 16034 260 42 6034 310 52 6234 360 72 6334 180 225 22 6836 250 33 6936 280 31 16036 280 46 6036 320 52 6236 380 75 6336 190 240 24 6838 260 33 6938 290 31 16038 290 46 6038 340 55 6238 400 78 6338 200 250 24 6840 280 38 6940 310 34 16040 310 51 6040 360 58 6240 420 80 6340 INTERCHANGE TABLE NSK ZZ VV DDU NR ZNR KOYO ZZ 2RU 2RS NR ZNR NTN ZZ LLB LLU NR ZNR SKF 2Z 2RZ 2RS1 NR ZNR FAG 2ZR - 2RSR NR ZRN* NACHI ZZE 2NKE 2NSE NR ZENR TO 75MM NACHI 75MM AND OVER ZZ 2NK 2NSL NR ZNR * Does not include Snap Ring Larger sizes are available. If the product you need is not listed, please contact your local branch.
BALL BEARINGS Single Row - Radial Inch Dimensions Bearing VARIANCE Alt ID OD W Number ZZ DDU NR No 0.125 0.3750 0.1563 R 2 0.188 0.5000 0.1563 R 3 EE1 0.250 0.6250 0.1960 R 4 0.250 0.7500 0.2188 R 4 A EE2 0.375 0.8750 0.2188 R 6 EE3 1.5000 0.5625 RMS 3 0.500 1.1250 0.2500 R 8 EE4 1.3125 0.3750 RLS 4 1.6250 0.6250 RMS 4 0.625 1.3750 0.2813 R 10 EE5 1.5625 0.4375 RLS 5 1.8125 0.6250 RMS 5 0.750 1.6250 0.3125 R 12 EE6 1.8750 0.5625 RLS 6 2.0000 0.6875 RMS 6 0.875 1.8750 0.3750 R 14 EE8 2.0000 0.5625 RLS 7 2.2500 0.6875 RMS 7 1.000 2.0000 0.3750 R 16 EE9 2.2500 0.6250 RLS 8 2.5000 0.7500 RMS 8 1.125 2.1250 0.3750 R 18 EE10 2.5000 0.6250 RLS 9 2.8125 0.8125 RMS 9 1.250 2.2500 0.3750 R 20 EE11 2.7500 0.6875 RLS 10 3.1250 0.8750 RMS 10 1.375 2.5000 0.4375 R 22 EE12 2.5625 0.5625 XLJ 1-3/8 3.0000 0.6875 RLS 11 3.5000 0.8750 RMS 11 1.500 2.6250 0.4375 R 24 EE13 2.6875 0.5625 XLJ 1-1/2 3.2500 0.7500 RLS 12 3.7500 0.9375 RMS 12 1.625 2.8750 0.5625 XLJ 1-5/8 3.5000 0.7500 RLS 13 4.0000 0.9375 RMS 13 Note: R series bearings equivalent to EE series have a greater width in the ZZ and 2RS varieties. The W measurement listed above refers to the open bearing. Phoenix bearings uses the same Part Number with suffix PH. XLJ sizes range from 5-15 inches. ZZ 2RS NR (DDU) Dimensions Bearing VARIANCE ID OD W Number ZZ DDU NR 1.750 3.0000 0.5625 XLJ 1-3/4 3.7500 0.8125 RLS 14 4.2500 1.0625 RMS 14 1.875 3.1875 0.6250 XLJ 1-7/8 4.0000 0.8125 RLS 15 4.5000 1.0625 RMS 15 2.000 3.3125 0.6250 XLJ 2 4.0000 0.8125 RLS 16 4.5000 1.0625 RMS 16 2.250 3.5625 0.6250 XLJ 2-1/4 4.5000 0.8750 RLS 18 5.0000 1.2500 RMS 18 2.500 3.8750 0.6875 XLJ 2-1/2 5.0000 0.9375 RLS 20 5.5000 1.2500 RMS 20 2.750 4.1250 0.6875 XLJ 2-3/4 5.2500 0.9375 RLS 22 6.2500 1.3750 RMS 22 3.000 4.5000 0.7500 XLJ 3 5.7500 1.0625 RLS 24 7.0000 1.5625 RMS 24 3.250 4.7500 0.7500 XLJ 3-1/4 6.0000 1.0625 RLS 26 7.5000 1.5625 RMS 26 3.375 7.5000 1.5625 RMS 27 3.500 5.0000 0.7500 XLJ 3-1/2 6.5000 1.1250 RLS 28 8.1250 1.7500 RMS 28 3.750 5.2500 0.7500 XLJ 3-3/4 6.7500 1.1250 RLS 30 8.2500 1.7500 RMS 30 4.000 5.6250 0.8750 XLJ 4 7.2500 1.2500 RLS 32 8.5000 1.7500 RMS 32 4.250 6.0000 0.8750 XLJ 4-1/4 7.5000 1.2500 RLS 34 8.7500 1.7500 RMS 34 4.500 6.2500 0.8750 XLJ 4-1/2 Dimensions in inches If the product you need is not listed, please contact your local branch. 19
BALL BEARINGS Single Row - Radial Inch and Inch Bore Metric Dimensions Bearing VARIANCE ID OD W Number ZZ DDU NR 8.0000 1.3125 RLS 36 9.3750 2.0000 RMS 36 4.750 6.5000 0.8750 XLJ 4-3/4 8.2500 1.3125 RLS 38 10.0000 2.0000 RMS 38 5.000 7.0000 1.0000 XLJ 5 8.0000 1.3750 RLS 40 10.0000 2.0000 RMS 40 5.250 7.2500 1.0000 XLJ 5-1/4 5.500 7.5000 1.0000 XLJ 5-1/2 9.5000 1.3750 RLS 44 11.0000 2.0000 RMS 44 5.750 7.7500 1.0000 XLJ 5-3/4 6.000 8.0000 1.0000 XLJ 6 10.5000 1.5625 RLS 48 12.0000 2.2500 RMS 48 6.500 8.7500 1.1250 XLJ 6-1/2 11.0000 1.5625 RLS 52 13.0000 2.5000 RMS 52 7.000 9.5000 1.2500 XLJ 7 12.0000 1.7500 RLS 56 13.5000 2.5000 RMS 56 7.500 10.0000 1.2500 XLJ 7-1/2 12.5000 1.7500 RLS 60 14.5000 2.7500 RMS 60 8.000 10.7500 1.3750 XLJ 8 13.0000 1.7500 RLS 64 15.0000 2.7500 RMS 64 8.500 11.5000 1.5000 XLJ 8-1/2 14.0000 2.0000 RLS 68 16.0000 3.0000 RMS 68 9.000 12.0000 1.5000 XLJ 9 14.5000 2.0000 RLS 72 17.0000 3.0000 RMS 72 Dimensions in inches. ZZ 2RS NR (DDU) Dimensions Bearing ID OD W Number 12.700 (0.500) 32 10 6201-08DDU 35 11 6202-08ZZ 35 11 6202-08DDU 40 12 6203-08ZZ 15.875 (0.625) 35 11 6202-10DDU 35 11 6202-10DDUNR 40 12 6203-625DDU 19.050 (0.750) 40 12 6203-12DDU 47 14 6204-750DDU 25.400 (1.000) 52 15 6205X2DDU25.4 Dimensions in mm. Inches shown in brackets. Note: Phoenix bearings uses the same Part Number with suffix PH. XLJ sizes range from 5-15 inches. If the product you need is not listed, please contact your local branch. 20
BALL BEARINGS Single Row - Maximum Capacity Metric Dimensions NSK VARIANCE ALTERNATE ID OD W Number Z ZZ NR ZNR NUMBER 12 32 10 BL201 15 35 11 BL202 42 13 BL302 17 40 12 BL203 M6203 47 14 BL303 20 47 14 BL204 M6204 52 15 BL304 25 52 15 BL205 M6205 62 17 BL305 M6305 30 62 16 BL206 M6206 72 19 BL306 M6306 35 72 17 BL207 M6207 80 21 BL307 M6307 40 80 18 BL208 M6208 90 23 BL308 M6308 45 85 19 BL209 M6209 100 25 BL309 M6309 50 90 20 BL210 M6210 110 27 BL310 M6310 55 100 21 BL211 M6211 120 29 BL311 M6311 60 110 22 BL212 M6212 130 31 BL312 M6312 65 120 23 BL213 M6213 140 33 BL313 M6313 70 125 24 BL214 M6214 150 35 BL314 M6314 75 130 25 BL215 M6215 160 37 BL315 M6315 80 140 26 BL216 M6216 170 39 BL316 M6316 85 150 28 BL217 M6217 180 41 BL317 M6317 90 160 30 BL218 M6218 190 43 BL318 M6318 95 170 32 BL219 M6219 200 45 BL319 M6319 100 180 34 BL220 M6220 215 47 BL320 M6320 110 200 38 BL222 120 215 40 BL224 130 230 40 BL226 Dimensions in mm. Z ZZ NR ZNR If the product you need is not listed, please contact your local branch. 21
BALL BEARINGS SINGLE ROW - SPHERICAL OD WIDE SERIES Spherical OD & Wide Series Metric Dimensions (mm) Bearing ID OD W Number 10 30 9 CS 200 DDU 12 32 10 CS 201 DDU 15 35 11 CS 202 DDU 17 40 12 CS 203 DDU 20 47 14 CS 204 DDU 25 52 15 CS 205 DDU 62 17 CS 305 DDU 30 62 16 CS 206 DDU 72 19 CS 306 DDU 35 72 17 CS 207 DDU 80 21 CS 307 DDU 40 80 18 CS 208 DDU 90 23 CS 308 DDU 45 85 19 CS 209 DDU 100 25 CS 309 DDU 50 90 20 CS 210 DDU 100 27 CS 310 DDU 62000 Series 63000 Series ZZ -2RS NR 62200 SERIES 62300 SERIES Part Number ID OD W 62200 10 30 14 62200-2RS 10 30 14 62201 12 32 14 62201-2RS 12 32 14 62202 15 35 14 62202-2RS 15 35 14 62203 17 40 16 62203-2RS 17 40 16 62204 20 47 18 62204-2RS 20 47 18 62205 25 52 18 62205-2RS 25 52 18 62206 30 62 20 62206-2RS 30 62 20 62207 35 72 23 62207-2RS 35 72 23 62208 40 80 23 62208-2RS 40 80 23 62209 45 85 23 62210 50 90 23 62211 55 100 25 62212 60 110 28 62213 65 120 31 62214 70 125 31 Part Number ID OD W 62300 10 35 17 62301 12 37 17 62301-2RS 12 37 17 62302 15 42 17 62302-2RS 15 42 17 62303 17 47 19 62303-2RS.75 40 12 62304 20 52 21 62304-2RS 20 52 21 62305 25 62 24 62305-2RS 25 62 24 62306 30 72 27 62307 35 80 31 62308 40 90 33 62309 45 100 36 62310 50 110 40 62311 55 120 43 62312 60 130 46 62313 65 140 48 62314 70 150 51 If the product you need is not listed, please contact your local branch. 22
BALL BEARINGS Extra Small & Miniature Metric OPEN ZZ VV Dimensions (mm) Bearing VARIANCE ID OD W W1 Number ZZ VV 1 3 1 681 3 1.5 OB03 4 1.6 691 1.2 4 1.8 OB05 1.5 4 1.2 2 68/1.5 5 2 2.6 69/1.5 6 2.5 3 OB08 2 5 1.5 2.3 682 5 2 2.5 OB11 6 2.3 3 692 6 2.5 3 OB13 7 2.5 3 OB14 7 2.8 3.5 602 2.5 6 1.8 2.6 68/2.5 7 2.5 3.5 69/2.5 8 2.5 OB16 8 2.8 4 OB17 3 6 2 2.5 ML3006 7 2 3 683 8 2.5 ML3008 8 3 4 693 9 3 5 603 10 4 4 623 13 5 5 633 4 7 2 2.5 ML4007 8 2 3 ML4008 9 2.5 4 684 10 3 4 ML4010 11 4 4 694 12 4 4 604 13 5 5 624 16 5 5 634 5 8 2 2.5 ML5008 9 2.5 3 ML5009 Dimensions (mm) Bearing VARIANCE ID OD W W1 Number ZZ VV 5 10 3 4 ML5010 11 3 5 685 13 4 4 695 14 5 5 605 16 5 5 625 19 6 6 635 6 10 2.5 3 ML6010 12 3 4 ML6012 13 3.5 5 686 15 5 5 696 17 6 6 606 19 6 6 626 19 8 8 OB47 22 7 7 636 7 11 2.5 3 ML7011 13 3 4 ML7013 14 3.5 5 687 17 5 5 697 19 6 6 607 22 7 7 627 22 8 8 OB52 26 9 9 637 8 12 2.5 3.5 ML8012 14 3.5 4 ML8014 16 4 5 688 19 6 6 698 22 7 7 608 24 8 8 628 28 9 9 638 9 17 4 5 689 20 6 6 699 24 7 7 609 26 8 8 629 30 10 10 639 If the product you need is not listed, please contact your local branch. 23
BALL BEARINGS Extra Small & Miniature Flanged - Metric OPEN ZZ Dimensions (mm) Bearing VARIANCE ID OD W W1 FD FD1 FW FW1 Number ZZ 1 3 1 3.8 0.3 F681 4 1.6 5 0.5 F691 1.5 4 1.2 2 5 5 0.4 0.6 F68/1.5 5 2 2.6 6.5 6.5 0.6 0.8 F69/1.5 6 2.5 3 7.5 7.5 0.6 0.8 OBF08 2 5 1.5 2.3 6.1 6.1 0.5 0.6 F682 5 2 2.5 6.2 6.2 0.6 0.6 OBF11 6 2.3 3 7.5 7.5 0.6 0.8 F692 6 2.5 3 7.2 7.2 0.6 0.6 OBF13 7 2.5 3 8.2 8.2 0.6 0.6 OBF14 7 2.8 3.5 8.5 8.5 0.7 0.9 F602 2.5 6 1.8 2.6 7.1 7.1 0.5 0.8 F68/2.5 7 2.5 3.5 8.5 8.5 0.7 0.9 F69/2.5 8 2.8 4 9.5 9.5 0.7 0.9 OBF17 3 6 2 2.5 7.2 7.2 0.6 0.6 MLF3006 7 2 3 8.1 8.1 0.5 0.8 F683 8 3 4 9.5 9.5 0.7 0.9 F693 9 3 5 10.5 10.5 0.7 1 F603 10 4 4 11.5 11.5 1 1 F623 13 5 5 15 15 1 1 F633 4 7 2 2.5 8.2 8.2 0.6 0.6 MLF4007 8 2 3 9.2 9.2 0.6 0.6 MLF4008 9 2.5 4 10.3 10.3 0.6 1 F684 10 3 4 11.2 11.6 0.6 0.8 MLF4010 11 4 4 12.5 12.5 1 1 F694 12 4 4 13.5 13.5 1 1 F604 13 5 5 15 15 1 1 F624 16 5 5 18 18 1 1 F634 If the product you need is not listed, please contact your local branch. 24
BALL BEARINGS Extra Small & Miniature Flanged - Metric OPEN ZZ Dimensions (mm) Bearing VARIANCE ID OD W W1 FD FD1 FW FW1 Number ZZ 5 8 2 2.5 9.2 9.2 0.6 0.6 MLF5008 9 2.5 3 10.2 10.2 0.6 0.6 MLF5009 10 3 4 11.2 11.6 0.6 0.8 MLF5010 11 3 5 12.5 12.5 0.8 1 F685 13 4 4 15 15 1 1 F695 14 5 5 16 16 1 1 F605 16 5 5 18 18 1 1 F625 19 6 6 22 22 1.5 1.5 F635 6 10 2.5 3 11.2 11.2 0.6 0.6 MLF6010 12 3 4 13.2 13.6 0.6 0.8 MLF6012 13 3.5 5 15 15 1 1.1 F686 15 5 5 17 17 1.2 1.2 F696 17 6 6 19 19 1.2 1.2 F606 19 6 6 22 22 1.5 1.5 F626 22 7 7 25 25 1.5 1.5 F636 7 11 2.5 3 12.2 12.2 0.6 0.6 MLF7011 13 3 4 14.2 14.6 0.6 0.8 MLF7013 14 3.5 5 16 16 1 1.1 F687 17 5 5 19 19 1.2 1.2 F697 19 6 6 22 22 1.5 1.5 F607 22 7 7 25 25 1.5 1.5 F627 26 9 9 29 29 2 2 F637 8 12 2.5 3.5 13.2 13.6 0.6 0.8 MLF8012 14 3.5 4 15.6 15.6 0.8 0.8 MLF8014 16 4 5 18 18 1 1.1 F688 19 6 6 22 22 1.5 1.5 F698 22 7 7 25 25 1.5 1.5 F608 9 17 4 5 19 19 1 1.1 F689 20 6 6 23 23 1.5 1.5 F699 24 7 7 27 27 1.5 1.5 F609 If the product you need is not listed, please contact your local branch. 25
BALL BEARINGS Single Row - Angular Contact Metric With Pressed Cage Dimensions (mm) Bearing ID OD W Number 10 26 8 7000 B 30 9 7200 B 35 11 7300 B 12 28 8 7001 B 32 10 7201 B 37 12 7301 B 15 32 9 7002 B 35 11 7202 B 42 13 7302 B 17 35 10 7003 B 40 12 7203 B 47 14 7303 B 20 42 12 7004 B 47 14 7204 B 52 15 7304 B 72 19 7404 B 25 47 12 7005 B 52 15 7205 B 62 17 7305 B 80 21 7405 B 30 55 13 7006 B 62 16 7206 B 72 19 7306 B 90 23 7406 B 35 62 14 7007 B 72 17 7207 B 80 21 7307 B 100 25 7407 B Ground face bearings are identified by the suffix G. These bearings have a standout between the inner ring and outer ring on both sides that are equal in size and can be matched in a variety of ways. The clearance size of such bearings when mounted should be C2 in general. Example: 7309 BG Dimensions (mm) Bearing ID OD W Number 40 68 15 7008 B 80 18 7208 B 90 23 7308 B 110 27 7408 B 45 75 16 7009 B 85 19 7209 B 100 25 7309 B 120 29 7409 B 50 80 16 7010 B 90 20 7210 B 110 27 7310 B 130 31 7410 B 55 90 18 7011 B 100 21 7211 B 120 29 7311 B 140 33 7411 B 60 95 18 7012 B 110 22 7212 B 130 31 7312 B 150 35 7412 B 65 100 18 7013 B 120 23 7213 B 140 33 7313 B 160 37 7413 B 70 110 20 7014 B 125 24 7214 B 150 35 7314 B 180 42 7414 B The standard contact angle is 40 and is identified by the suffix B. Other angles of contact available are 30 with a suffix A and 15 with a suffix C. Standard cage material is Pressed Steel with suffix W. Other cage materials available include machined brass identified by suffix M. If the product you need is not listed, please contact your local branch. 26
BALL BEARINGS Single Row - Angular Contact Metric With Pressed Cage Dimensions (mm) Bearing ID OD W Number 75 115 20 7015 B 130 25 7215 B 160 37 7315 B 190 45 7415 B 80 125 22 7016 B 140 26 7216 B 170 39 7316 B 200 48 7416 B 85 130 22 7017 B 150 28 7217 B 180 41 7317 B 210 52 7417 B 90 140 24 7018 B 160 30 7218 B 190 43 7318 B 225 54 7418 B 95 145 24 7019 B 170 32 7219 B 200 45 7319 B 100 150 24 7020 B 180 34 7220 B 215 47 7320 B 105 160 26 7021 B 190 36 7221 B 225 49 7321 B 110 170 28 7022 B 200 38 7222 B 240 50 7322 B Ground face bearings are identified by the suffix G. These bearings have a standout between the inner ring and outer ring on both sides that are equal in size and can be matched in a variety of ways. The clearance size of such bearings when mounted should be C2 in general. Example: 7309 BG Dimensions (mm) Bearing ID OD W Number 120 180 28 7024 B 215 40 7224 B 260 55 7324 B 130 200 33 7026 B 230 40 7226 B 280 58 7326 B 140 210 33 7028 B 250 42 7228 B 300 62 7328 B 150 225 35 7030 B 270 45 7230 B 320 65 7330 B 160 240 38 7032 B 290 48 7232 B 340 68 7332 B 170 260 42 7034 B 310 52 7234 B 360 72 7334 B 180 280 46 7036 B 320 52 7236 B 380 75 7336 B 190 290 46 7038 B 340 55 7238 B 400 78 7338 B 200 310 51 7040 B 360 58 7240 B 420 80 7340 B The standard contact angle is 40 and is identified by the suffix B. Other angles of contact available are 30 with a suffix A and 15 with a suffix C. Standard cage material is Pressed Steel with suffix W. Other cage materials available include machined brass identified by suffix M. If the product you need is not listed, please contact your local branch. 27
BALL BEARINGS Single Row - Angular Contact Inch With Pressed Cage Dimensions (inch) Bearing ID OD W Number 0.375 1.5000 0.5625 MJT 3/8MB 0.500 1.3125 0.3750 LJT 1/2MB 1.6250 0.6250 MJT 1/2MB 0.625 1.5625 0.4375 LJT 5/8MB 1.8125 0.6250 MJT 5/8MB 0.750 1.8750 0.5625 LJT 3/4MB 2.0000 0.6875 MJT 3/4MB 0.875 2.0000 0.5625 LJT 7/8MB 2.2500 0.6875 MJT 7/8MB 1.000 2.2500 0.6250 LJT 1MB 2.5000 0.7500 MJT 1MB 1.125 2.5000 0.6250 LJT 1-1/8MB 2.8125 0.8125 MJT 1-1/8MB 1.250 2.7500 0.6875 LJT 1-1/4MB 3.1250 0.8750 MJT 1-1/4MB 1.375 3.0000 0.6875 LJT 1-3/8MB 3.5000 0.8750 MJT 1-3/8MB 1.500 3.2500 0.7500 LJT 1-1/2MB 3.7500 0.9375 MJT 1-1/2MB 1.625 3.5000 0.7500 LJT 1-5/8MB 4.0000 0.9375 MJT 1-5/8MB 1.750 3.7500 0.8125 LJT 1-3/4MB 4.2500 1.0625 MJT 1-3/4MB 1.875 4.0000 0.8125 LJT 1-7/8MB 4.5000 1.0625 MJT 1-7/8MB 2.000 4.0000 0.8125 LJT 2MB 4.5000 1.0625 MJT 2MB 2.250 4.5000 0.8750 LJT 2-1/4MB 5.0000 1.2500 MJT 2-1/4MB 2.500 5.0000 0.9375 LJT 2-1/2MB 5.5000 1.2500 MJT 2-1/2MB 2.750 5.2500 0.9375 LJT 2-3/4MB 6.2500 1.3750 MJT 2-3/4MB 3.000 5.7500 1.0625 LJT 3MB Dimensions (inch) Bearing ID OD W Number 3.000 7.0000 1.5625 MJT 3MB 3.250 6.0000 1.0625 LJT 3-1/4MB 7.5000 1.5625 MJT 3-1/4MB 3.375 7.5000 1.5625 MJT 3-3/8MB 3.500 6.5000 1.1250 LJT 3-1/2MB 8.1250 1.7500 MJT 3-1/2MB 3.750 6.7500 1.1250 LJT 3-3/4MB 8.2500 1.7500 MJT 3-3/4MB 4.000 7.2500 1.2500 LJT 4MB 8.5000 1.7500 MJT 4MB 4.250 7.5000 1.2500 LJT 4-1/4MB 8.7500 1.7500 MJT 4-1/4MB 4.500 8.0000 1.3125 LJT 4-1/2MB 9.3750 2.0000 MJT 4-1/2MB 4.750 8.2500 1.3125 LJT 4-3/4MB 10.0000 2.0000 MJT 4-3/4MB 5.000 9.0000 1.3750 LJT 5MB 10.0000 2.0000 MJT 5MB 5.500 9.5000 1.3750 LJT 5-1/2MB 11.0000 2.0000 MJT 5-1/2MB 6.000 10.5000 1.5625 LJT 6MB 12.0000 2.2500 MJT 6MB 6.500 11.0000 1.5625 LJT 6-1/2MB 13.0000 2.5000 MJT 6-1/2MB 7.000 12.0000 1.7500 LJT 7MB 13.5000 2.5000 MJT 7MB 7.500 12.5000 1.7500 LJT 7-1/2MB 14.5000 2.7500 MJT 7-1/2MB 8.000 13.0000 1.7500 LJT 8MB 15.0000 2.7500 MJT 8MB 8.500 14.0000 2.0000 LJT 8-1/2MB 16.0000 3.0000 MJT 8-1/2MB 9.000 14.5000 2.0000 LJT 9MB 17.0000 3.0000 MJT 9MB Notes: Standard contact angle is 20. Other contact angles are 15 with suffix X2 and 30 with suffix X4. Phoenix bearings LJT sizes range from 3-15 inches and MJT sizes range from 2 3/4-12 and uses the same part number with suffix of PH. If the product you need is not listed, please contact your local branch. 28
BALL BEARINGS Single Row - Duplex (QJ) Metric & Inch Dimensions (mm) Bearing ID OD W Number 17 40 12 QJ 203 20 47 14 QJ 204 52 15 QJ 304 25 52 15 QJ 205 62 17 QJ 305 30 62 16 QJ 206 72 19 QJ 306 35 72 17 QJ 207 80 21 QJ 307 40 80 18 QJ 208 90 23 QJ 308 45 85 19 QJ 209 100 25 QJ 309 50 90 20 QJ 210 110 27 QJ 310 55 100 21 QJ 211 120 29 QJ 311 60 110 22 QJ 212 130 31 QJ 312 65 120 23 QJ 213 140 33 QJ 313 70 125 24 QJ 214 150 35 QJ 314 75 130 25 QJ 215 160 37 QJ 315 80 140 26 QJ 216 170 39 QJ 316 85 150 28 QJ 217 180 41 QJ 317 90 160 30 QJ 218 190 43 QJ 318 95 170 32 QJ 219 200 45 QJ 319 100 180 34 QJ 220 215 47 QJ 320 105 225 49 QJ 321 110 200 38 QJ 222 240 50 QJ 322 Dimensions (inch) Bearing ID OD W Number 1.000 2.2500 0.6250 QJL 1 2.5000 0.7500 QJM 1 1.125 2.5000 0.6250 QJL 1-1/8 2.8125 0.8125 QJM 1-1/8 1.250 2.7500 0.6875 QJL 1-1/4 3.1250 0.8750 QJM 1-1/4 1.375 3.0000 0.6875 QJL 1-3/8 3.5000 0.8750 QJM 1-3/8 1.500 3.2500 0.7500 QJL 1-1/2 3.7500 0.9375 QJM 1-1/2 1.625 3.5000 0.7500 QJL 1-5/8 4.0000 0.9375 QJM 1-5/8 1.750 3.7500 0.8125 QJL 1-3/4 4.2500 1.0625 QJM 1-3/4 1.875 4.0000 0.8125 QJL 1-7/8 4.5000 1.0625 QJM 1-7/8 2.000 4.0000 0.8125 QJL 2 4.5000 1.0625 QJM 2 2.250 4.5000 0.8750 QJL 2-1/4 5.0000 1.2500 QJM 2-1/4 2.500 5.0000 0.9375 QJL 2-1/2 5.5000 1.2500 QJM 2-1/2 2.750 5.2500 0.9375 QJL 2-3/4 6.2500 1.3750 QJM 2-3/4 3.000 5.7500 1.0625 QJL 3 7.0000 1.5625 QJM 3 3.250 6.0000 1.0625 QJL 3-1/4 7.5000 1.5625 QJM 3-1/4 3.375 7.5000 1.5625 QJM 3-3/8 3.500 6.5000 1.1250 QJL 3-1/2 8.1250 1.7500 QJM 3-1/2 3.750 6.7500 1.1250 QJL 3-3/4 8.2500 1.7500 QJM 3-3/4 4.000 7.2500 1.2500 QJL 4 8.5000 1.7500 QJM 4 4.250 8.7500 1.7500 QJM 4-1/4 4.500 8.0000 1.3125 QJL 4-1/2 9.3750 2.0000 QJM 4-1/2 4.750 10.0000 2.0000 QJM 4-3/4 5.000 10.0000 2.0000 QJM 5 5.500 11.0000 2.0000 QJM 5-1/2 6.000 12.0000 2.2500 QJM 6 Note: Phoenix bearings QJ sizes range from 318-356mm, QJL sizes range from 3-6 1/2 inches, QJM sizes range from 3-6 inches, and uses the same part number with a suffix of PH. If the product you need is not listed, please contact your local branch. 29
BALL BEARINGS Single Row - Magneto Metric Dimensions (mm) Bearing ID OD W Number 3 16 5 E 3 4 16 5 E 4 5 16 5 E 5 6 21 7 E 6 7 22 7 E 7 8 24 7 E 8 9 28 8 E 9 10 28 8 E 10 12 32 7 E 12 13 30 7 E 13 15 35 8 E 15 17 40 10 E 17 20 47 12 E 20 20 47 12 R20-11XSA* * Tapered Roller If the product you need is not listed, please contact your local branch. 30
BALL BEARINGS Thrust - Single Direction Metric With Flat Back Faces With Aligning Seat Washer (U) Dimensions (mm) Bearing Number ID C ID OD W With Flat With Aligning Back Faces Seat Washer 10 11 24 9 51100 12 26 11 51200 53200 U 12 13 26 9 51101 14 28 11 51201 53201 U 15 16 28 9 51102 17 32 12 51202 53202 U 17 18 30 9 51103 19 35 12 51203 53203 U 20 21 35 10 51104 22 40 14 51204 53204 U 25 26 42 11 51105 27 47 15 51205 53205 U 27 52 18 51305 53305 U 27 60 24 51405 53405 U 30 32 47 11 51106 32 52 16 51206 53206 U 32 60 21 51306 53306 U 32 70 28 51406 53406 U 35 37 52 12 51107 37 62 18 51207 53207 U 37 68 24 51307 53307 U 37 80 32 51407 53407 U 40 42 60 13 51108 42 68 19 51208 53208 U 42 78 26 51308 53308 U 42 90 36 51408 53408 U 45 47 65 14 51109 47 73 20 51209 53209 U Dimensions (mm) Bearing Number ID C ID OD W With Flat With Aligning Back Faces Seat Washer 45 47 85 28 51309 53309 U 47 100 39 51409 53409 U 50 52 70 14 51110 52 78 22 51210 53210 U 52 95 31 51310 53310 U 52 110 43 51410 53410 U 55 57 78 16 51111 57 90 25 51211 53211 U 57 105 35 51311 53311 U 57 120 48 51411 53411 U 60 62 85 17 51112 62 95 26 51212 53212 U 62 110 35 51312 53312 U 62 130 51 51412 53412 U 65 67 90 18 51113 67 100 27 51213 53213 U 67 115 36 51313 53313 U 68 140 56 51413 53413 U 70 72 95 18 51114 72 105 27 51214 53214 U 72 125 40 51314 53314 U 73 150 60 51414 53414 U 75 77 100 19 51115 77 110 27 51215 53215 U 77 135 44 51315 53315 U 78 160 65 51415 53415 U 80 82 105 19 51116 82 115 28 51216 53216 U The dimensions shown in the table are for a bearing with flat back faces. For dimensions W 1 and OD 1, please contact your local branch. 31
BALL BEARINGS Thrust - Single Direction Metric With Flat Back Faces With Aligning Seat Washer (U) Dimensions (mm) Bearing Number ID C ID OD W With Flat With Aligning Back Faces Seat Washer 80 82 140 44 51316 53316 U 83 170 68 51416 53416 U 85 87 110 19 51117 88 125 31 51217 53217 U 88 150 49 51317 53317 U 88 180 72 51417 53417 U 90 92 120 22 51118 93 135 35 51218 53218 U 93 155 50 51318 53318 U 93 190 77 51418 53418 U 100 102 135 25 51120 103 150 38 51220 53220 U 103 170 55 51320 53320 U 103 210 85 51420 53420 U 110 112 145 25 51122 113 160 38 51222 53222 U 113 190 63 51322 53322 U 113 230 95 51422 120 122 155 25 51124 123 170 39 51224 53224 U 123 210 70 51324 53324 U 123 250 102 51424 130 132 170 30 51126 133 190 45 51226 53226 U 134 225 75 51326 53326 U 134 270 110 51426 The dimensions shown in the table are for a bearing with flat back faces. For dimensions W 1 and OD 1, please contact your local branch. Dimensions (mm) Bearing Number ID C ID OD W With Flat With Aligning Back Faces Seat Washer 140 142 180 31 51128 143 200 46 51228 53228 U 144 240 80 51328 53328 U 144 280 112 51428 150 152 190 31 51130 153 215 50 51230 53230 U 154 250 80 51330 53330 U 154 300 120 51430 160 162 200 31 51132 163 225 51 51232 53232 U 164 270 87 51332 53332 U 164 320 130 51432 170 172 215 34 51134 173 240 55 51234 53234 U 174 280 87 51334 53334 U 174 340 135 51434 180 183 225 34 51136 183 250 56 51236 53236 U 184 300 95 51336 53336 U 184 360 140 51436 190 193 240 37 51138 194 270 62 51238 53238 U 195 320 105 51338 53338 U 200 203 250 37 51140 204 280 62 51240 53240 U 205 340 110 51340 53340 U 32
BALL BEARINGS Thrust - Single Direction Inch FT XLT,, LT,, MT Dimensions (inches) Bearing ID C ID OD C OD W Number 0.250 0.656 0.250 FT 1/4 0.281 0.813 0.781 0.375 LT 1/4 0.313 0.750 0.250 FT 5/16 0.344 1.000 0.969 0.531 LT 5/16 0.375 0.813 0.250 FT 3/8 0.406 1.000 0.969 0.531 LT 3/8 0.438 0.875 0.250 FT 7/16 0.469 1.281 1.250 0.625 LT 7/16 0.500 0.969 0.250 FT 1/2 0.531 1.281 1.250 0.625 LT 1/2 0.563 0.594 1.406 1.375 0.625 LT 9/16 0.625 1.094 0.281 FT 5/8 0.656 1.406 1.375 0.625 LT 5/8 0.750 1.313 0.281 FT 3/4 0.781 1.531 1.500 0.625 LT 3/4 0.813 1.563 1.500 0.719 MT 3/4 0.875 1.500 0.375 FT 7/8 0.906 1.656 1.625 0.625 LT 7/8 0.938 1.813 1.750 0.750 MT 7/8 1.000 1.625 0.375 FT 1 1.031 1.781 1.750 0.625 LT 1 1.125 2.000 1.875 0.750 MT 1 1.125 1.750 0.375 FT 1-1/8 1.156 1.906 1.875 0.625 LT 1-1/8 1.250 2.250 2.125 0.875 MT 1-1/8 1.250 2.063 0.500 FT 1-1/4 1.250 2.063 2.063 0.719 LT 1-1/4 1.375 2.500 2.375 1.000 MT 1-1/4 1.375 2.188 0.500 FT 1-3/8 1.406 2.219 2.188 0.719 LT 1-3/8 1.500 2.313 0.500 FT 1-1/2 1.531 2.344 2.313 0.719 LT 1-1/2 1.625 2.875 2.750 1.125 MT 1-1/2 1.625 2.438 0.500 FT 1-5/8 1.656 2.469 2.438 0.719 LT 1-5/8 1.750 2.625 0.625 FT 1-3/4 1.781 2.688 2.656 0.750 LT 1-3/4 1.875 3.313 3.188 1..250 MT 1-3/4 Dimensions (inches) Bearing ID C ID OD C OD W Number 1.875 2.750 0.625 FT 1-7/8 1.906 2.813 2.781 0.750 LT 1-7/8 2.000 2.875 0.625 FT 2 2.031 2.969 2.938 0.750 LT 2 2.031 3.063 3.031 0.688 XLT 2 2.125 3.688 3.563 1.375 MT 2 2.125 2.156 3.188 3.156 0.688 XLT 2-1/8 2.156 3.219 3.188 0.875 LT 2-1/8 2.250 3.125 0.625 FT 2-1/4 2.281 3.313 3.281 0.688 XLT 2-1/4 2.281 3.344 3.313 0.875 LT 2-1/4 2.375 4.250 4.125 1.688 MT 2-1/4 2.375 2.406 3.438 3.406 0.688 XLT 2-3/8 2.406 3.594 3.563 1.000 LT 2-3/8 2.500 2.531 3.563 3.531 0.688 XLT 2-1/2 2.531 3.719 3.688 1.000 LT 2-1/2 2.625 4.750 4.625 2.000 MT 2-1/2 2.625 2.656 3.750 3.719 0.750 XLT 2-5/8 2.656 3.844 3.813 1.000 LT 2-5/8 2.750 2.781 3.875 3.844 0.750 XLT 2-3/4 2.781 4.031 4.000 1.000 LT 2-3/4 2.875 5.000 4.875 2.000 MT 2-3/4 2.875 2.906 4.000 3.969 0.750 XLT 2-7/8 2.906 4.156 4.125 1.000 LT 2-7/8 3.000 3.063 4.125 4.063 0.750 XLT 3 3.063 4.375 4.313 1.125 LT 3 3.125 5.625 5.500 2.250 MT 3 3.125 3.188 4.500 4.438 1.125 LT 3-3/8 3.250 3.313 4.375 4.313 0.750 XLT 3-1/4 3.313 4.813 4.750 1.250 LT 3-1/4 3.375 3.438 4.938 4.875 1.250 LT 3-3/8 3.500 3.563 4.625 4.563 0.750 XLT 3-1/2 3.563 5.063 5.000 1.250 LT 3-1/2 3.625 6.438 6.313 2.500 MT 3-1/2 3.625 3.688 5.188 5.125 1.250 LT 3-5/8 3.750 3.813 4.875 4.813 0.750 XLT 3-3/4 3.813 5.313 5.250 1.250 LT 3-3/4 3.875 3.938 5.688 5.625 1.375 LT 3-7/8 If the product you need is not listed, please contact your local branch. 33
BALL BEARINGS Thrust - Single Direction Inch XLT,, LT,, MT Dimensions (inches) Bearing ID C ID OD C OD W Number 4.000 4.063 5.250 5.188 0.875 XLT 4 4.063 5.813 5.750 1.375 LT 4 4.125 7.250 7.125 2.813 MT 4 4.250 4.313 6.313 6.250 1.750 LT 4-1/4 4.500 4.563 5.750 5.688 1.000 XLT 4-1/2 4.563 6.563 6.500 1.750 LT 4-1/2 4.625 8.375 8.250 3.375 MT 4-1/2 4.750 4.813 7.063 7.000 2.000 LT 4-3/4 5.000 5.063 6.500 6.438 1.125 XLT 5 5.063 7.313 7.250 2.000 LT 5 5.125 9.500 9.375 4.000 MT 5 5.500 5.563 7.000 6.938 1.125 XLT 5-1/2 5.563 8.063 8.000 2.188 LT 5-1/2 5.625 10.375 10.250 4.250 MT 5-1/2 6.000 6.063 7.625 7.563 1.250 XLT 6 6.063 8.688 8.625 2.375 LT 6 6.125 11.125 11.000 4.500 MT 6 6.500 6.625 8.125 8.000 1.250 XLT 6-1/2 6.625 9.406 9.281 2.500 LT 6-1/2 7.000 7.125 8.750 8.625 1.375 XLT 7 7.125 10.125 10.000 2.625 LT 7 7.125 12.750 12.625 5.000 MT 7 7.500 7.625 9.250 9.125 1.375 XLT 7-1/2 7.625 10.875 10.750 2.750 LT 7-1/2 8.000 8.125 10.000 9.875 1.500 XLT 8 8.125 11.625 11.500 3.000 LT 8 8.125 14.375 14.250 5.625 MT 8 8.500 8.625 10.500 10.375 1.500 XLT 8-1/2 9.000 9.125 11.250 11.125 1.875 XLT 9 9.125 13.125 13.000 13.500 LT 9 If the product you need is not listed, please contact your local branch. 34
BALL BEARINGS Thrust - Double Direction Metric With Flat Back Faces Dimensions (mm) Bearing Number ID C ID OD W With Flat With Aligning Back Faces Seat Washer With Aligning Seat Washer (U) Dimensions (mm) Bearing Number ID C ID OD W With Flat With Aligning Back Faces Seat Washer 10 17 32 22 52202 54202 U 15 22 40 26 52204 54204 U 27 60 45 52405 54405 U 20 27 47 28 52205 54205 U 27 52 34 52305 54305 U 32 70 52 52406 54406 U 25 32 52 29 52206 54206 U 32 60 38 52306 54306 U 37 80 59 52407 54407 U 30 37 62 34 52207 54207 U 42 68 36 52208 54208 U 37 68 44 52307 54307 U 42 78 49 52308 54308 U 42 90 65 52408 54408 U 35 47 73 37 52209 54209 U 47 85 52 52309 54309 U 47 100 72 52409 54409 U 40 52 78 39 52210 54210 U 52 95 58 52310 54310 U 52 110 78 52410 54410 U 45 57 90 45 52211 54211 U 57 105 64 52311 54311 U 57 120 87 52411 54411 U 50 62 95 46 52212 54212 U 62 110 64 52312 54312 U 62 130 93 52412 54412 U 68 140 101 52413 54413 U 55 67 100 47 52213 54213 U 72 105 47 52214 54214 U 67 115 65 52313 54313 U 72 125 72 52314 54314 U 73 150 107 52414 54414 U 60 77 110 47 52215 54215 U 77 135 79 52315 54315 U 78 160 115 52415 54415 U 65 82 115 48 52216 54216 U 82 140 79 52316 54316 U 83 170 120 52416 54416 U The dimensions shown in the table are for a bearing with flat back faces. For dimensions W 1 and OD 1, please contact your local branch. 65 88 180 128 52417 54417 U 70 88 125 55 52217 54217 U 88 150 87 52317 54317 U 93 190 135 52418 54418 U 75 93 135 62 52218 54218 U 93 155 88 52318 54318 U 80 103 210 150 52420 54420 U 85 103 150 67 52220 54220 U 170 97 52320 54320 U 90 113 230 166 52422 95 113 160 67 52222 54222 U 113 190 110 52322 54322 U 123 250 177 52424 100 123 170 68 52224 54224 U 123 210 123 52324 54324 U 134 270 192 52426 110 133 190 80 52226 54226 U 134 225 130 52326 144 280 196 52428 120 143 200 81 52228 54228 U 144 240 140 52328 154 300 209 52430 130 153 215 89 52230 54230 U 154 250 140 52330 164 320 226 52432 135 174 340 236 52434 140 163 225 90 52232 54232 U 164 270 153 52332 184 360 245 52436 150 173 240 97 52234 54234 U 183 250 98 52236 54236 U 174 280 153 52334 184 300 165 52336 160 194 270 109 52238 54238 U 195 320 183 52338 170 204 280 109 52240 54240 U 205 340 192 52340 190 224 300 110 52244 54244 U 35
BALL BEARINGS Double Row - Self Aligning Metric 36 Parallel bore Tapered bore Adapter assembly Dimensions (mm) Bearing VARIANCE Adapter Sleeves ID OD W Number K Ref MM Ref INCH 5 19 6 135 6 19 6 126 7 22 7 127 8 22 7 108 9 26 8 129 10 30 9 1200 30 14 2200 35 11 1300 35 17 2300 12 32 10 1201 32 14 2201 37 12 1301 37 17 2301 15 35 11 1202 35 14 2202 42 13 1302 42 17 2302 17 40 12 1203 40 16 2203 47 14 1303 47 19 2303 20 47 14 1204 H204 17 47 18 2204 52 15 1304 H304 17 52 21 2304 25 52 15 1205 H205 20 HE205 3/4 52 18 2205 H305 20 HE305 3/4 62 17 1305 H305 20 HE305 3/4 62 24 2305 H2305 20 HE2305 3/4 30 62 16 1206 H206 25 HE206 1 62 20 2206 H306 25 HE306 1 72 19 1306 H306 25 HE306 1 72 27 2306 H2306 25 HE2306 1 90 28 1406 35 72 17 1207 H207 30 72 23 2207 H307 30 80 21 1307 H307 30 80 31 2307 H2307 30 100 30 1407 40 80 18 1208 H208 35 HE208 1-1/4 80 23 2208 H308 35 HE308 1-1/4 90 23 1308 H308 35 HE308 1-1/4 90 33 2308 H2308 35 HE2308 1-1/4 110 33 1408 45 85 19 1209 H209 40 HE209 1-1/2 85 23 2209 H309 40 HE309 1-1/2 100 25 1309 H309 40 HE309 1-1/2 100 36 2309 H2309 40 HE2309 1-1/2 120 35 1409 50 90 20 1210 H210 45 HE210 1-3/4 90 23 2210 H310 45 HE310 1-3/4 110 27 1310 H310 45 HE310 1-3/4 If the product you need is not listed, please contact your local branch.
BALL BEARINGS Double Row - Self Aligning Metric Parallel bore Tapered bore Adapter assembly Dimensions (mm) Bearing VARIANCE Adapter Sleeves ID OD W Number K Ref MM Ref INCH 50 110 40 2310 H2310 45 HE2310 1-3/4 130 37 1410 55 100 21 1211 H211 50 HE211 2 100 25 2211 H311 50 HE311 2 120 29 1311 H311 50 HE311 2 120 43 2311 H2311 50 HE2311 2 140 40 1411 60 110 22 1212 H212 55 110 28 2212 H312 55 130 31 1312 H312 55 130 46 2312 H2312 55 150 42 1412 65 120 23 1213 H213 60 HE213 2-1/4 120 31 2213 H313 60 HE313 2-1/4 140 33 1313 H313 60 HE313 2-1/4 140 48 2313 H2313 60 HE2313 2-1/4 70 125 24 1214 125 31 2214 150 35 1314 150 51 2314 75 130 25 1215 H215 65 HE215 2-1/2 130 31 2215 H315 65 HE315 2-1/2 160 37 1315 H315 65 HE315 2-1/2 160 55 2315 H2315 65 HE2315 2-1/2 80 140 26 1216 H216 70 HE216 2-3/4 140 33 2216 H316 70 HE316 2-3/4 170 39 1316 H316 70 HE316 2-3/4 170 58 2316 H2316 70 HE2316 2-3/4 85 150 28 1217 H217 75 HE217 3 150 36 2217 H317 75 HE317 3 180 41 1317 H317 75 HE317 3 180 60 2317 H2317 75 HE2317 3 90 160 30 1218 H218 80 HE218 3-1/4 160 40 2218 H318 80 HE318 3-1/4 190 43 1318 H318 80 HE318 3-1/4 190 64 2318 H2318 80 HE2318 3-1/4 95 170 32 1219 H219 85 HE219 3-1/4 170 43 2219 H319 85 HE319 3-1/4 200 45 1319 H319 85 HE319 3-1/4 200 67 2319 H2319 85 HE2319 3-1/4 100 180 34 1220 H220 90 HE220 3-1/2 180 46 2220 H320 90 HE320 3-1/2 215 47 1320 H320 90 HE320 3-1/2 215 73 2320 H2320 90 HE2320 3-1/2 105 190 36 1221 H221 95 190 50 2221 H321 95 110 200 38 1222 H222 100 HE222 4 200 53 2222 H322 100 HE322 4 240 50 1322 H322 100 HE322 4 240 80 2322 H2322 100 HE2322 4 120 215 42 1224 H3024 110 HE3124 4-1/4 130 230 46 1226 If the product you need is not listed, please contact your local branch. 37
BALL BEARINGS Double Row - Self Aligning Inch Dimensions (inch) Bearing ID OD W Number 0.500 1.3125 0.3750 NLJ 1/2 1.6250 0.6250 NMJ 1/2 0.625 1.5625 0.4375 NLJ 5/8 1.8125 0.6250 NMJ 5/8 0.750 1.8750 0.5625 NLJ 3/4 2.0000 0.6875 NMJ 3/4 0.875 2.0000 0.5625 NLJ 7/8 2.2500 0.6875 NMJ 7/8 1.000 2.2500 0.6250 NLJ 1 2.5000 0.7500 NMJ 1 1.125 2.5000 0.6250 NLJ 1-1/8 2.8125 0.8125 NMJ 1-1/8 1.250 2.7500 0.6875 NLJ 1-1/4 3.1250 0.8750 NMJ 1-1/4 1.375 3.0000 0.6875 NLJ 1-3/8 3.5000 0.8750 NMJ 1-3/8 1.500 3.2500 0.7500 NLJ 1-1/2 3.7500 0.9375 NMJ 1-1/2 1.625 3.5000 0.7500 NLJ 1-5/8 4.0000 0.9375 NMJ 1-5/8 1.750 3.7500 0.8125 NLJ 1-3/4 4.2500 1.0625 NMJ 1-3/4 1.875 4.0000 0.8125 NLJ 1-7/8 4.5000 1.0625 NMJ 1-7/8 2.000 4.0000 0.8125 NLJ 2 4.5000 1.0625 NMJ 2 2.250 4.5000 0.8750 NLJ 2-1/4 5.0000 1.2500 NMJ 2-1/4 Note: Phoenix bearings uses the same Part Numbers with a suffix of PH. Dimensions (inch) Bearing ID OD W Number 2.500 5.0000 0.9375 NLJ 2-1/2 5.5000 1.2500 NMJ 2-1/2 2.750 5.2500 0.9375 NLJ 2-3/4 6.2500 1.3750 NMJ 2-3/4 3.000 5.7500 1.0625 NLJ 3 7.0000 1.5625 NMJ 3 3.250 6.0000 1.0625 NLJ 3-1/4 7.5000 1.5625 NMJ 3-1/4 3.375 7.5000 1.5625 NMJ 3-3/8 3.500 6.5000 1.1250 NLJ 3-1/2 8.1250 1.7500 NMJ 3-1/2 3.750 6.7500 1.1250 NLJ 3-3/4 8.2500 1.7500 NMJ 3-3/4 4.000 7.2500 1.2500 NLJ 4 8.5000 1.7500 NMJ 4 4.250 7.5000 1.2500 NLJ 4-1/4 8.7500 1.7500 NMJ 4-1/4 4.500 8.0000 1.3125 NLJ 4-1/2 9.3750 2.0000 NMJ 4-1/2 4.750 8.2500 1.9375 NLJ 4-3/4 10.0000 2.0000 NMJ 4-3/4 5.000 9.0000 1.3750 NLJ 5 10.0000 2.0000 NMJ 5 5.500 9.5000 1.3750 NLJ 5-1/2 11.0000 2.0000 NMJ 5-1/2 6.000 10.5000 1.5625 NLJ 6 12.0000 2.2500 NMJ 6 If the product you need is not listed, please contact your local branch. 38
BALL BEARINGS Double Row - Radial Metric Dimensions (mm) Bearing ID OD W Number 10 30 14 4200 35 17 4300 12 32 14 4201 37 17 4301 15 35 14 4202 42 17 4302 17 40 16 4203 47 19 4303 20 47 18 4204 52 21 4304 25 52 18 4205 62 24 4305 30 62 20 4206 72 27 4306 35 72 23 4207 80 31 4307 40 80 23 4208 90 33 4308 45 85 23 4209 100 36 4309 50 90 23 4210 110 40 4310 55 100 25 4211 120 43 4311 60 110 28 4212 130 46 4312 65 120 31 4213 140 48 4313 70 125 31 4214 150 51 4314 75 130 31 4215 160 55 4315 80 140 33 4216 170 58 4316 85 150 36 4217 90 160 40 4218 95 170 43 4219 100 180 46 4220 If the product you need is not listed, please contact your local branch. 39
BALL BEARINGS Double Row - Angular Contact Metric 52, 53 without filling slot 52...ZZ 53...ZZ 52...2RS 53...2RS 32, 33 with filling slot Dimensions (mm) Bearing VARIANCE ID OD W Number ZZ 2RS 17 40 17.5 5203 20 47 20.6 5204 52 22.2 5304 25 52 20.6 5205 62 25.4 5305 30 62 23.8 5206 72 30.2 5306 35 72 27.0 5207 80 34.9 5307 40 80 30.2 5208 90 36.5 5308 45 85 30.2 5209 100 39.7 5309 50 90 30.2 5210 110 44.4 5310 55 100 33.3 5211 120 49.2 5311 60 110 36.5 5212 130 54.0 5312 65 120 38.1 5213 140 58.7 5313 70 125 39.7 5214 150 63.5 5314 75 160 68.3 5315 Double-row angular contact ball bearings accommodate radial load and axial load in both directions. The 52 and 53 series are a standard capacity type and are available shielded or sealed. The 32 and 33 series are a maximum capacity type provided with a filling slot and no seal options. 32 and 33 series: contact angle 32 52 and 53 series: contact angle 24 If the product you need is not listed, please contact your local branch. Dimensions (mm) Bearing ID OD W Number 10 30 14.3 3200 12 32 15.9 3201 15 35 15.9 3202 42 19.0 3302 17 40 17.5 3203 47 22.2 3303 20 47 20.6 3204 52 22.2 3304 25 52 20.6 3205 62 25.4 3305 30 62 23.8 3206 72 30.2 3306 35 72 27.0 3207 80 34.9 3307 40 80 30.2 3208 90 36.5 3308 45 85 30.2 3209 100 39.7 3309 50 90 30.2 3210 110 44.4 3310 55 100 33.3 3211 120 49.2 3311 60 110 36.5 3212 130 54.0 3312 65 120 38.1 3213 140 58.7 3313 70 125 39.7 3214 150 63.5 3314 75 130 41.3 3215 160 68.3 3315 80 140 44.4 3216 170 68.3 3316 85 150 49.2 3217 180 73.0 3317 90 160 52.4 3218 190 73.0 3318 95 170 55.6 3219 200 77.8 3319 100 180 60.3 3220 215 82.6 3320 105 190 65.1 3221 225 87.3 3321 110 200 69.8 3222 240 92.1 3322 40
BALL BEARINGS Triangle s Lazy Susan FEATURES TYPICAL USES Attaches easily to second surface even though hidden after it is fastened to first surface. Only 5/16 thick! Engineered to add a minimum of height to item, with only a rolling contact between sections. (Can be recessed into surfaces, reducing space to 1/8. Also can be inverted if desirable.) Triangle s large ball race designed for maximum stability. Has a full race of precision ground ball bearings for smooth gliding rotation. One-unit construction. No separate parts, but preassembled so there is no contact under load except through the rolling balls. Center opening allows for center post and ease of centering the unit. Triangle s 360 interlock prevents separation of moving parts. Bearing is interlocked for lifetime of unit. No rivet to work loose or bind. Zinc coated for rust resistance. Corner Cabinet Shelves Spice Shelves Book Stands Bird Feeders Weather Vanes Flower Racks Serving Trays Picnic Tables Cake Decorators Yarn Winders Boat Seats Shoe Racks Scrabble Turntables Ceramics and Sculpturing Coffee Tables Furniture Novelties Advertising Displays Advertising Signs TV Turntables Canned Goods Storage Storage-Door Closets Rotating Wardrobes Machine Stands Model Rwy. Turntables Toys and Games Book Shelves Paint Spray Turntables Portable Radio Turntables Office Stationery Holders Stairwell Closet Storage Industrial Assembly Fixtures SIZES AVAILABLE SIZE & PART CENTER HOLE DIAMETER NOMINAL LOAD TURNTABLE SHAPES NO INCH MM LBS KGS DIAM (Approx) 3" square 3C 1-1/4" 31.5 200 90 to 18" 4" square 4C 2-5/32" 54.8 300 136 12" to 25" 6" square 6C 4-11/16" 119.1 500 226 15" to 30" 9" square 9C 4-1/2" 114.3 750 340 17" to 35" 12" round 12C 6-9/32" 159.5 1000 450 20" & over 41
BALL BEARINGS Sprag Clutches MODEL CSK Ball and roller bearing over-running clutches. Individually spring-loaded locking rollers. MODEL AS Built-in over-running clutch extra narrow series. Individually springloaded locking rollers. MODEL ASNU Built-in over-running clutch narrow series with face grooves. Individually spring-loaded locking rollers. Dimensions (mm) Part Number ID OD W / Other WARNER Manufacturer 8 22 9 CSK8 15 35 11 CSK15 17 40 12 CSK17 KK17 20 47 14 CSK20 KK20 25 52 15 CSK25 KK25 30 62 16 CSK30 KK30 35 72 17 CSK35 KK35 8 24 8 AS8 NSS8 10 30 9 AS10 NSS10 12 32 10 AS12 NSS12 15 35 11 AS15 NSS15 20 47 14 AS20 NSS20 25 52 15 AS25 NSS25 30 62 16 AS30 NSS30 35 72 17 AS35 NSS35 40 80 18 AS40 NSS40 45 85 19 AS45 NSS45 50 90 20 AS50 NSS50 60 110 22 AS60 NSS60 8 35 13 ASNU8 NFS8 12 35 13 ASNU12 NFS12 15 42 18 ASNU15 NFS15 17 47 19 ASNU17 NFS17 20 52 21 ASNU20 NFS20 25 62 24 ASNU25 NFS25 30 72 27 ASNU30 NFS30 35 80 31 ASNU35 NFS35 40 90 33 ASNU40 NFS40 45 100 36 ASNU45 NFS45 50 110 40 ASNU50 NFS50 60 130 46 ASNU60 NFS60 70 150 51 ASNU70 NFS70 80 170 58 ASNU80 NFS80 If the product you need is not listed, please contact your local branch. 42
BALL BEARINGS NSK One-Way Clutches 1. Outer race 2. Inner race 3. Cam 4. Garter spring 5. Bearing 6. Retaining ring 7. Side plate DIMENSIONS (mm) ID OD IR W OR W PART NUMBER 15 68 62 60 GX15 17 75 66 64 GX17 20 80 67 65 GX20 22 100 82 80 GX22 25 100 82 80 GX25 30 100 82 80 GX30 35 110 87 85 GX35 40 125 92 90 GX40 45 125 92 90 GX45 50 155 102 100 GX50 55 155 102 100 GX55 60 155 102 100 GX60 65 175 105 103 GX65 70 175 105 103 GX70 Features: NSK s GX-series One-Way Clutches incorporate a host of features designed to support further improvements in the productivity and safety of industrial machinery. Maintenance-free operation GX series One-Way Clutches are permanently lubricated and are supplied ready-to-use. They require no maintenance such as greasing up, cleaning grease changing, offering significant economies of time and labour. A broad operating temperature range The lubricant used in GX series is a special high-performance grease developed by NSK. It assures outstanding reliability over an ambient operating temperature range of -20 to +80 C. High Torque capacity Wide cams with a larger radius of curvature than conventional models achieve high torque capacity under high loads for improved safety. A unique cam shape allows the GX series to withstand even shock loads without slipping. Long service life NSK s expertise in ball bearing manufacturing technology ensures high dimensional precision of the cams, and inner and outer races, offering long service life. The high performance grease used to lubricate the GX series also helps minimise the wear on each part and prolong its life. Easy to use GX series One-Way Clutches are supplied as integral systems with all components built in. They are ready to be used as it is. 43
BALL BEARINGS 44
Super Precision Bearings Hybrid RHP Ultra... 46 Single Row-Radial... 46 Single Row-Angular Contact... 47 Ball Screw Support... 48 BSB Metric Series... 48 45
SUPER PRECISION Single Row Radial Ball Bearing Designation System 6 0 10 T B CN P4 6 Type 6 Single row radial ball bearing 0 10 T RHP ISO RHP ISO Dimension 2 02 Series 0 10 3 03 00 10mm 04 upwards, multiply Bore 01 12mm by 5 to obtain bore Code 02 15mm size in mm 03 17mm Normal type Construction S Ceramic ball type Cage T Phenolic resin Material M Brass TN/TNH Polyamide Denotes standard feature, no indicator necessary ** Denotes mean figure given in m Dimensions Bearing Dimensions ID OD W Number ID OD W 10 26 8 6000 TBR12P4 30 9 6200 TBR12P4 12 28 8 6001 TBR12P4 32 10 6201 TBR12P4 15 32 9 6002 TBR12P4 35 11 6202 TBR12P4 17 35 10 6003 TBR12P4 40 12 6203 TBR12P4 20 42 12 6004 TBR12P4 47 14 6204 TBR12P4 52 15 6304 TBR12P4 25 47 12 6005 TBR12P4 52 15 6205 TBR12P4 62 17 6305 TBR12P4 B Inner ring guided B Location A Outer ring guided BH Inner ring guided C1 C2 Radial Standard R.I.C. CN Internal C3 Clearance C4 Special R.I.C. R** Special Axial Fit A** RHP ISO ABEC P5 5 5 Precision P4 4 7 Grade P3 Dimensional accuracy P4 Running accuracy P2 P2 2 9 CN P4 Bearing Number 30 55 13 6006 TBR12P4 62 16 6206 TBR12P4 72 19 6306 TBR12P4 35 62 14 6007 TBR12P4 72 17 6207 TBR12P4 80 21 6307 TBR12P4 40 68 15 6008 TBR12P4 80 18 6208 TBR12P4 90 23 6308 TBR12P4 45 75 16 6009 TBR12P4 85 19 6209 TBR12P4 100 25 6309 TBR12P4 Other Precision Grades (eg. P2, P5 and P6) are available. Dimensions Bearing ID OD W Number 50 80 16 6010 TBR12P4 90 20 6210 TBR12P4 110 27 6310 TBR12P4 55 90 18 6011 TBR12P4 100 21 6211 TBR12P4 120 29 6311 TBR12P4 60 95 18 6012 TBR12P4 110 22 6212 TBR12P4 130 31 6312 TBR12P4 65 100 18 6013 TBR12P4 120 23 6213 TBR12P4 140 33 6313 TBR12P4 70 110 20 6014 TBR12P4 125 24 6214 TBR12P4 150 35 6314 TBR12P4 Single Row-Radial Metric Radial Metric Dimensions Bearing ID OD W Number 75 115 20 6015 TBR12P4 130 25 6215 TBR12P4 160 37 6315 TBR12P4 80 125 22 6016 TBR12P4 140 26 6216 TBR12P4 170 39 6316 TBR12P4 85 130 22 6017 TBR12P4 150 28 6217 TBR12P4 180 41 6317 TBR12P4 90 140 24 6018 TBR12P4 190 43 6318 TBR12P4 95 145 24 6019 TBR12P4 100 150 24 6020 TBR12P4 110 170 28 6022 TBR12P4 Hybrid RHP Ultra T70**S ISO Series 10 46 Hybrid RHP Ultra T170**S: Single Row Angular Contact Ball Bearing with Ceramic Balls Primary Limiting Load Abutment Dimensions Grease PCD of Dimensions Speeds Ratings max fillet radius Volume Lubri- Basic Dyna Static d1* D1* cation d D B Bearing Oil/Air Grease Co Cor r r1 min max 20% P mm rev/ min N mm cm 3 mm 20 42 12 T7004SCTSU 92500 56500 7490 3520 0.6 0.3 23 39 0.7 27.6 25 47 12 T7005SCTSU 79500 48500 8330 4340 0.6 0.3 28 44 0.8 32.6 30 55 13 T7006SCTSU 67500 41000 10300 5550 1.0 0.6 35 50 1.1 36.7 35 62 14 T7007SCTSU 59000 36000 13000 7400 1.0 0.6 40 57 1.5 44.2 40 68 15 T7008SCTSU 53000 32500 14100 8650 1.0 0.6 45 63 1.8 49.7 45 75 16 T7009SCTSU 47500 29000 16700 10500 1.0 0.6 50 70 2.4 55.3 50 80 16 T7010SCTSU 44000 27000 17200 11300 1.0 0.6 55 75 2.6 60.3 55 90 18 T7011SCTSU 37500 23500 20800 14300 1.0 1.0 60 85 3.5 67.4 60 95 18 T7012SCTSU 35500 21000 21400 15200 1.0 1.0 65 90 3.8 72.4 65 100 18 T7013SCTSU 33000 20000 24800 17700 1.0 1.0 70 95 4.2 77.0 70 110 20 T7014SCTSU 30500 18000 32200 23400 1.0 1.0 75 105 5.7 63.7 75 115 20 T7015SCTSU 29000 16500 32000 23700 1.0 1.0 80 110 6.1 66.7 80 125 22 T7016SCTSU 26500 15000 35900 27100 1.0 1.0 85 120 7.8 95.6 85 130 22 T7017SCTSU 25500 14000 36900 28700 1.0 1.0 90 125 8.2 100.6 90 140 24 T7018SCTSU 24000 13000 42400 34000 1.5 1.5 97.5 132.5 10.0 107.9 *Abutment dimensions are suitable for both sides of the bearing.
SUPER PRECISION Single Row-Angular Contact Metric Single Row Angular Contact Ball Bearing Designation System 7 0 10 C T DU M P4 Construction 7 Type 0 Normal range X Small ball "RHP EXCEL" range T RHP Ultra range 7 Single row angular contact ball bearing Dimension RHP ISO RHP ISO Series 9 19 2 02 0 10 3 03 00 10mm 02 15mm Bore 01 12mm 03 17mm 10 Code 04 upwards, multiply by 5 to obtain bore size in mm C T Construction Normal Type R Reverse Type S Ceramic Ball Type Contact C 15 o A 30 o Angle E 25 o Cage T/ET Phenolic Material Resin TN/TNH/ETN Denotes standard feature, no indicator necessary. ** Denotes mean figure given in m. Location Outer ring guided Phenolic cages A Outer ring guided cages except Phenolic B Inner ring guided SU Single universal DU, DB, DF, DT Paired unit DU Grouping 3U, 3T, 2TB, 2TF Triple set QU, QB, QF, 3TB, 3TF Quad Set 3B2, 3F2, 4TB, 4TF Set of 5 M Preload P4 S Slack M Medium F Flush H Heavy X Extra Light G** Special Preload L Light A** Special Axial Load GX Extra Light GL Light For standard and RHP Excel ceramic ball bearings Special Refer to NSK-RHP for details. Precision Applies only to single bearings. RHP ISO Class ABEC RHP ISO Class ABEC Precision P6 6 3 P3 Dim. Accuracy P4 Grade P5 5 5 Run Accuracy P2 P4 4 7 P2 2 9 Special Feature Refer to NSK-RHP for details. Angular Contact Super Precision Metric Dimensions Bearing Number ID OD W NSK RHP Fafnir 10 26 8 7000CTYDULP4 7000CTRDULP4 2MM9100WICRDUL 30 9 7200CTYDULP4 7200CTRDULP4 2MM200WICRDUL 12 28 8 7001CTYDULP4 7001CTRDULP4 2MM9101WICRDUL 32 10 7201CTYDULP4 7201CTRDULP4 2MM201WICRDUL 15 32 9 7002CTYDULP4 7002CTRDULP4 2MM9102WICRDUL 35 11 7202CTYDULP4 7202CTRDULP4 2MM202WICRDUL 17 30 7 7903CTYDULP4 7903CTRDULP4 2MM9303WICRDUL 35 10 7003CTYDULP4 7003CTRDULP4 2MM9103WICRDUL 40 12 7203CTYDULP4 7203CTRDULP4 2MM203WICRDUL 47 14 7303CTYDULP4 7303CTRDULP4 2MM303WICRDUL 20 37 9 7904CTYDULP4 7904CTRDULP4 2MM9304WICRDUL 42 12 7004CTYDULP4 7004CTRDULP4 2MM9104WICRDUL 47 14 7204CTYDULP4 7204CTRDULP4 2MM204WICRDUL 52 15 7304CTYDULP4 7304CTRDULP4 2MM304WICRDUL 25 42 9 7905CTYDULP4 7905CTRDULP4 2MM9305WICRDUL 47 12 7005CTYDULP4 7005CTRDULP4 2MM9105WICRDUL 52 15 7205CTYDULP4 7205CTRDULP4 2MM205WICRDUL 62 17 7305CTYDULP4 7305CTRDULP4 2MM305WICRDUL 30 47 9 7906CTYDULP4 7906CTRDULP4 2MM9306WICRDUL 55 13 7006CTYDULP4 7006CTRDULP4 2MM9106WICRDUL 62 16 7206CTYDULP4 7206CTRDULP4 2MM206WICRDUL 72 19 7306CTYDULP4 7306CTRDULP4 2MM306WICRDUL Other Precision Grades (eg. P2, P5 and P6) are available. 47
SUPER PRECISION Ball Screw Support Ball Screw Support Bearings and Units Designation Systems BSB 025 062 DU M P3 BSB Type BSB Ball Screw Support Bearing U Cartridge Unit BSPB Pillow Block Unit RHP ISO Dimension Non ISO Series 2 02 3 03 RHP Metric RHP Inch 025 for Brgs Bore Size in mm Nom size in 25 for Units Code 100ths of an inch e.g. 150 = 1-1/2" 062 RHP Metric For BSB Size in mm (except O.D. for ISO Series) Code For U Housing diameter in mm For BSPB Base to bore centreline height in mm. RHP Inch SU Single Universal DU, DB, DF, DT Paired Unit DU Grouping 3U, 3T, 2TB, 2TF Triple Set QU, QB, QF, 3TB, 3TF Quad Set M P3 Preload RHP L M H H G** Level Light-Metric Series Medium-Metric Series Heavy-Metric Series Standard Preload-Inch Series Special Preload Special Refer to Precision NSK-RHP Applies only to single bearings for details Dimensional accuracy P4. Precision Grade Running accuracy P2. BSB Metric Series No indicator used to denote this feature. ** Denotes mean figure given in m. The figures listed in the L, M and H columns below for axial stiffness, limiting speeds and drag torque are based on the L (Light), M (Medium) and H (Heavy) preload values given in this table. * Abutment diameters are suitable for both sides of the bearing. ** Preload, axial stiffness and limiting speeds are for pairs of bearings mounted either backto-back or face-to-face. Primary Dimensions Ball Screw Support Bearings - BSB Metric Series Axial Load Abut Dim. Ratings max fillet ra. Basic Dyna Static d 1 * D 1 * Preload Axial Stiffness** Limiting Speeds** Drag Torque d D B Bearing C o C or r min max L M H L M H L M H L M H mm N mm N N/ rev/ Nm/ μm min bearing 17 47 15 BSB017047 23000 34200 0.6 23 42 875 1750 3500 480 610 750 4800 4200 3300 0.04 0.08 0.16 20 47 15 BSB020047 23000 34200 0.6 26 42 875 1750 3500 480 610 750 4800 4200 3300 0.04 0.08 0.16 25 62 15 BSB025062 26500 47500 1.0 35 56 1125 2250 4000 650 815 1000 3300 2900 2300 0.05 0.11 0.21 30 62 15 BSB030062 26500 47500 1.0 37 56 1125 2250 4500 650 815 1000 3300 2900 2300 0.05 0.11 0.21 72 15 BSB030072 31900 61900 1.0 37 66 1700 3400 6800 800 1000 1270 2900 2600 2000 0.06 0.12 0.24 35 72 15 BSB035072 31900 61900 1.0 42 66 1700 3400 6800 800 1000 1270 2900 2600 2000 0.06 0.12 0.24 100 20 BSB035100 63600 130000 1.0 42 90 3200 6400 12800 1090 1360 1750 2200 1900 1500 0.18 0.35 0.69 40 72 15 BSB040072 31900 61900 1.0 46 66 1700 3400 6800 800 1000 1270 2900 2600 2000 0.06 0.12 0.24 90 15 BSB040090 36500 86100 1.0 46 82 1975 3950 7900 1000 1290 1630 2300 2000 1600 0.09 0.18 0.36 100 20 BSB040100 63600 130000 1.0 49 90 3200 6400 12800 1090 1360 1750 2200 1900 1500 0.18 0.35 0.69 45 75 15 BSB045075 33700 69800 1.0 51 69 1700 3400 6800 840 1070 1370 2800 2400 1900 0.07 0.14 0.28 100 20 BSB045100 63600 130000 1.0 54 90 3200 6400 12800 1090 1360 1750 2200 1900 1500 0.18 0.35 0.69 50 90 15 BSB050090 36500 86100 1.0 56 82 1975 3950 7900 1000 1290 1630 2300 2000 1600 0.09 0.18 0.36 100 20 BSB050100 63600 130000 1.0 59 90 3200 6400 12800 1090 1360 1750 2200 1900 1500 0.18 0.35 0.69 55 90 15 BSB055090 36500 86100 1.0 63 82 1975 3950 7900 1000 1290 1630 2300 2000 1600 0.09 0.18 0.36 120 20 BSB055120 67800 156000 1.0 65 110 3900 7800 15600 1280 1590 2080 1800 1600 1250 0.20 0.39 0.78 60 120 20 BSB060120 67800 156000 1.0 69 110 3900 7800 15600 1280 1590 2080 1800 1600 1250 0.20 0.39 0.78 75 110 15 BSB075110 39700 111000 1.0 84 102 2500 5000 10000 1260 1620 2050 1800 1600 1250 0.11 0.22 0.44 100 150 22,5 BSB100150 77900 225000 1.0 110 140 5250 10500 21000 1800 2250 2850 1300 1150 900 0.27 0.53 1.06 48
Roller Bearings Cylindrical Roller... 50 Single Row - Metric... 51 Single Row - Imperial... 54 Single & Double Row... 55 EM & EW Series... 56 EM Series... 57 EW Series... 59 Cylindrical Hyload... 60 Spherical Roller... 63 HPS... 63 Double Row... 65 Double Row - Vibrating Screen... 67 Mounting Procedure... 68 Interchange Table... 69 Spherical Thrust... 70 49
ROLLER BEARINGS Cylindrical Roller Cylindrical roller bearings feature high radial load capacity because the rollers and raceway are in linear contact. These bearings are suitable for applications that involve heavy radial and impact loading. They are also appropriate for high-speed applications in that they can be machined very accurately due to their structure. Having a separable inner ring or outer ring, these bearings can be mounted and dismounted easily. NU - Rollers attached to Outer Race with a loose Inner Race. N - Rollers attached to Inner Race with a loose Outer Race. Single-Row cylindrical roller bearings NJ - Rollers attached to Outer Race with a loose Inner Race with a Lip on one side. The NU and N types exhibit their best performance when used as free side bearings since they adjust to the shaft s axial movement, to a certain extent, relative to the housing position. The NJ and NF types carry axial load in one direction, while the NUP and NH types can carry a certain degree of axial load in both directions. Type E cylindrical roller bearings feature enhanced load rating capacity compared with standard series, though both have equal dimensions. They are identified by supplementary code E. NF - Rollers attached to Inner Race with a loose Outer Race with a Lip on one side. NUP - Non-removable. Single-row cylindrical roller bearings Bore diameter 20-460 mm Thrust collar Bore diameter 20-320 mm Double-Row cylindrical roller bearings Double-row cylindrical roller bearings Double-row cylindrical roller bearings come in two types: with a cylindrical bore, and with a tapered bore. As for those with a tapered bore, the specified amount of clearance can be obtained by adjusting the press-in distance. These bearings can accommodate high radial loads, and are often used on machine tool spindles. Bearings with internal clearance greater than standard (eg identified by suffix C3) are also available. When ordering, please advise any special requirement such as high speed, high temperature or high running accuracy. Bore diameter 25-480 mm 50
ROLLER BEARINGS NU Cylindrical Single Row: METRIC Cylindrical Roller Single Row - Metric NJ NUP N NF Dimensions Variance Dimensions Variance REF REF I D O D W NU NJ NUP N NF Size Code I D O D W NU NJ NUP N NF Size Code 20 47 14 204 45 75 16 1009 20 47 14 204E 45 85 19 209 20 47 18 2204 45 85 19 209E 20 47 18 2204E 45 85 23 2209E 20 52 15 304 45 100 25 309 20 52 15 304E 45 100 25 309E 20 52 21 2304 45 100 36 2309E 20 52 21 2304E 45 120 29 409 25 47 12 1005 50 80 16 1010 25 52 15 205 50 90 20 210 25 52 15 205E 50 90 20 210E 25 52 18 2205E 50 90 23 2210E 25 62 17 305 50 110 27 310 25 62 17 305E 50 110 27 310E 25 62 24 2305E 50 110 40 2310E 25 80 21 405 50 130 31 410 30 55 13 1006 55 90 18 1011 30 62 16 206 55 100 21 211 30 62 16 206E 55 100 21 211E 30 62 20 2206E 55 100 25 2211E 30 72 19 306 55 120 29 311 30 72 19 306E 55 120 29 311E 30 72 27 2306E 55 120 43 2311E 30 90 23 406 55 140 33 411 35 62 14 1007 60 95 18 1012 35 72 17 207 60 110 22 212 35 72 17 207E 60 110 22 212E 35 72 23 2207E 60 110 28 2212E 35 80 21 307 60 130 31 312 35 80 21 307E 60 130 31 312E 35 80 31 2307E 60 130 46 2312E 35 100 25 407 60 150 35 412 40 68 15 1008 65 100 18 1013 40 80 18 208 65 120 23 213 40 80 18 208E 65 120 23 213E 40 80 23 2208E 65 120 31 2213E 40 90 23 308 65 140 33 313 40 90 23 308E 65 140 33 313E 40 90 33 2308E 65 140 48 2313E 40 110 27 408 65 160 37 413 Note: Phoenix bearings uses the same Part Number with a suffix of PH. Code sizes range from 318-356. 51
ROLLER BEARINGS NU Cylindrical Roller Single Row - Metric Cylindrical Single Row: METRIC NJ NUP N NF Dimensions Variance Dimensions Variance REF REF I D O D W NU NJ NUP N NF Size Code I D O D W NU NJ NUP N NF Size Code 70 110 20 1014 95 145 24 1019 70 125 24 214 95 170 32 219 70 125 24 214E 95 170 32 219E 70 125 31 2214E 95 170 43 2219E 70 150 35 314 95 200 45 319 70 150 35 314E 95 200 45 319E 70 150 51 2314E 95 200 67 2319E 70 180 42 414 95 240 55 419 75 115 20 1015 100 150 24 1020 75 130 25 215 100 180 34 220 75 130 25 215E 100 180 34 220E 75 130 31 2215E 100 180 46 2220E 75 160 37 315 100 215 47 320 75 160 37 315E 100 215 47 320E 75 160 55 2315E 100 215 73 2320E 75 190 45 415 100 250 58 420 80 125 22 1016 105 160 26 1021 80 140 26 216 105 190 36 221 80 140 26 216E 105 190 36 221E 80 140 33 2216E 105 225 49 321 80 170 39 316 105 225 49 321E 80 170 39 316E 105 260 60 421 80 170 58 2316E 110 170 28 1022 80 200 48 416 110 200 38 222 85 130 22 1017 110 200 38 222E 85 150 28 217 110 200 53 2222E 85 150 28 217E 110 240 50 322 85 150 36 2217E 110 240 50 322E 85 180 41 317 110 280 65 422 85 180 41 317E 120 180 28 1024 85 180 60 2317E 120 215 40 224 85 210 52 417 120 215 40 224E 90 140 24 1018 120 215 58 2224E 90 160 30 218 120 260 55 324 90 160 30 218E 120 260 55 324E 90 160 40 2218E 120 260 86 2324E 90 190 43 318 120 310 72 424 90 190 43 318E Note: Phoenix bearings uses the same Part Number with a suffix of 90 190 64 2318E PH. Code sizes range from 318-356. 90 225 54 418 52
ROLLER BEARINGS Cylindrical Roller Single Row Metric and Imperial Dimensions Variance I D O D W NU NJ NUP N NF 130 200 33 1026 130 230 40 226 130 230 40 226E 130 230 64 2226E 130 280 58 326 130 280 58 326E 130 280 93 2326E 130 340 78 426 140 210 33 1028 140 250 42 228 140 250 42 228E 140 250 68 2228E 140 300 62 328 140 300 62 328E 140 300 102 2328E 140 360 82 428 150 225 35 1030 150 270 45 230 150 270 45 230E 150 270 73 2230E 150 320 65 330 150 320 65 330E 150 320 108 2330E 150 380 85 430 160 240 38 1032 160 290 48 232 160 290 48 232E 160 290 80 2232E 160 340 68 332 160 340 68 332E 160 340 114 2332E 170 260 42 1034 170 310 52 234 170 310 52 234E 170 31 86 2234E 170 360 72 334 170 360 72 334E 170 360 120 2334E Dimensions Variance REF Size Code I D O D W NU NJ NUP N NF Cylindrical Single Row: IMPERIAL REF Size Code 180 280 46 1036 180 320 52 236 180 320 52 236E 180 320 86 2236E 180 380 75 336 180 380 75 336E 180 380 126 2336E 190 290 46 1038 190 340 55 238 190 340 55 238E 190 340 92 2238E 190 400 78 338 190 400 78 338E 190 400 132 2338E 200 310 51 1040 200 360 58 240 200 360 58 240E 200 360 98 2240E 200 420 80 340 200 420 80 340E 200 420 138 2340E 220 340 56 1044 220 400 65 244 220 400 108 2244 220 460 88 344 240 360 56 1048 240 440 72 248 240 440 120 2248 240 500 95 348 260 400 65 1052 260 480 80 252 260 480 130 2252 260 540 102 352 280 420 65 1056 280 500 80 256 300 460 74 1060 300 540 85 260 Note: Phoenix bearings uses the same Part Number with a suffix of PH. Code sizes range from 318-356. Used in applications where high radial loads exist or when axial shaft expansion has to be accommodated. Normally used in conjunction with another bearing capable of taking axial loads, but can be used with the appropriate rib configuration to provide shaft axial location and to support modest axial loading. The various rib formations are chosen to suit the needs of the application in terms of shaft axial location and ring retention. Cylindrical roller bearings are also made with specially controlled running tolerances and design features for traction motor type applications. XLRJ No Axial Location LLRJ LRJ No Axial Location MMRJ No Axial Location MRJ LRJA MRJA No Axial Location Axial Location in One Direction 53
ROLLER BEARINGS Cylindrical Roller Single Row - Imperial Part Number Example: LRJ2-1/2 Dimensions Variance Ref. ID OD W XLRJ LLRJ LRJ LRJA MMRJMRJ MRJA Size Code 3.000 4.500 0.750 3 5.750 1.063 3 7.000 1.563 3 3.250 4.750 0.750 3-1/4 6.000 1.063 3-1/4 7.500 1.563 3-1/4 3.375 7.500 1.563 3-3/8 3.500 5.000 0.750 3-1/2 6.500 1.125 3-1/2 8.125 1.750 3-1/2 3.750 5.250 0.750 3-3/4 6.750 1.125 3-3/4 8.250 1.750 3-3/4 Dimensions Variance Ref. 4.000 5.625 0.875 4 ID OD W XLRJ LLRJ LRJ LRJA MMRJMRJ MRJA Size 7.250 1.250 4 Code 8.500 1.750 4 0.500 1.313 0.375 1/2 4.250 6.000 0.875 4-1/4 1.625 0.625 1/2 7.500 1.250 4-1/4 0.625 1.563 0.438 5/8 8.750 1.750 4-1/4 1.813 0.625 5/8 4.500 6.250 0.875 4-1/2 0.750 1.875 0.563 3/4 8.000 1.313 4-1/2 2.000 0.688 3/4 9.375 2.000 4-1/2 0.875 2.000 0.563 7/8 4.750 6.500 0.875 4-3/4 2.250 0.688 7/8 8.250 1.313 4-3/4 1.000 2.250 0.625 1 10.000 2.000 4-3/4 2.250 0.750 1 5.000 7.000 1.000 5 1.125 2.500 0.625 1-1/8 9.000 1.375 5 2.813 0.813 1-1/8 10.000 2.000 5 1.250 2.750 0.688 1-1/4 5.250 7.250 1.000 5-1/4 3.125 0.875 1-1/4 5.500 7.500 1.000 5-1/2 1.375 3.000 0.688 1-3/8 9.500 1.375 5-1/2 3.500 0.875 1-3/8 11.000 2.000 5-1/2 1.500 2.688 0.563 1-1/2 5.750 7.750 1.000 5-3/4 3.250 0.750 1-1/2 6.000 8.000 1.000 6 3.750 0.938 1-1/2 10.500 1.563 6 1.625 2.875 0.563 12.000 2.250 6 3.500 0.750 1-5/8 6.500 8.750 1.125 6-1/2 11.000 1.563 6-1/2 4.000 0.938 1-5/8 13.000 2.500 6-1/2 1.750 3.000 0.563 1-3/4 7.000 9.500 1.250 7 3.750 0.813 1-3/4 12.000 1.750 7 4.250 1.063 1-3/4 13.500 2.500 7 1.875 3.188 0.625 1-7/8 7.500 10.000 1.250 7-1/2 4.000 0.813 1-7/8 12.500 1.750 7-1/2 4.500 1.063 1-7/8 14.500 2.750 7-1/2 2.000 3.313 0.625 2 8.000 10.750 1.375 8 4.000 0.813 2 13.000 1.750 8 4.500 1.063 2 15.000 2.750 8 2.250 3.563 0.625 2-1/4 8.500 11.500 1.500 8-1/2 4.500 0.875 2-1/4 14.000 2.000 8-1/2 5.000 5.250 2-1/4 16.000 3.000 8-1/2 2.500 3.875 0.688 2-1/2 9.000 12.000 1.500 9 5.000 0.938 2-1/2 14.500 2.000 9 5.500 1.250 2-1/2 17.000 3.000 9 2.750 4.125 0.688 2-3/4 9.500 12.750 1.625 9-1/2 5.250 0.938 2-3/4 15.125 2.000 9-1/2 6.250 1.375 2-3/4 18.000 3.250 9-1/2 Note: Larger sizes are available in machined brass cage. Phoenix bearings uses the same Part Number with a suffix of PH. If the product you need is not listed, please contact your local branch. 54
ROLLER BEARINGS Cylindrical Roller Single & Double Row Part Number Example: LRJ2-1/2 Note: Larger sizes are available in machined brass cage. Phoenix bearings uses the same Part Number with a suffix of PH. Dimensions Variance Ref. ID OD W XLRJ LLRJ LRJ LRJA MMRJMRJ MRJA Size Code 10.000 13.250 1.625 10 15.750 2.000 10 18.500 3.250 10 10.500 14.000 1.750 10-1/2 16.625 2.250 10-1/2 19.500 3.500 10-1/2 11.000 14.500 1.750 11 17.500 2.250 11 20.000 3.500 11 11.500 15.250 1.875 11-1/2 18.000 2.344 11-1/2 12.000 16.000 2.000 12 18.500 2.625 12 21.500 3.750 12 13.000 17.500 2.250 13 20.000 2.750 13 14.000 18.500 2.250 14 21.500 2.875 14 15.000 20.000 2.500 15 22.500 3.000 15 NN Cylindrical Double Row - Metric NNU Taper 1/12 Taper 1/12 Cylindrical Bore Tapered Bore Cylindrical Bore Tapered Bore Dimensions Bearing Number ID OD W Cylindrical Tapered Bore Bore 25 47 16 NN3005 NN3005K 30 55 19 NN3006 NN3006K 35 62 20 NN3007 NN3007K 40 68 21 NN3008 NN3008K 45 75 23 NN3009 NN3009K 50 80 23 NN3010 NN3010K 55 90 26 NN3011 NN3011K 60 95 26 NN3012 NN3012K 65 100 26 NN3013 NN3013K 70 110 30 NN3014 NN3014K 75 115 30 NN3015 NN3015K 80 125 34 NN3016 NN3016K 85 130 34 NN3017 NN3017K 90 140 37 NN3018 NN3018K 95 145 37 NN3019 NN3019K Dimensions Bearing Number ID OD W Cylindrical Tapered Bore Bore 100 150 37 NN3020 NN3020K 100 140 40 NNU4920 NNU4920K 105 160 41 NN3021 NN3021K 105 145 40 NNU4921 NNU4921K 110 170 45 NN3022 NN3022K 110 150 40 NNU4922 NNU4922K 120 180 46 NN3024 NN3024K 120 165 45 NNU4924 NNU4924K 130 200 52 NN3026 NN3026K 130 180 50 NNU4926 NNU4926K 140 210 53 NN3028 NN3028K 140 190 50 NNU4928 NNU4928K 150 225 56 NN3030 NN3030K 150 210 60 NNU4930 NNU4930K 160 240 60 NN3032 NN3032K 55
ROLLER BEARINGS EM Series Cylindrical Roller EM & EW Series NSK has been supplying a standard cage for smaller-sized, single row cylindrical roller bearings as indicated here: Standard Machined Cage --- M type (Riveted-type two-piece brass landriding cage) High Load-Carrying E Type -- MA1 type (One-piece brass land-riding cage) In the 21st century, you can now take advantage of NSK s newly developed cylindrical roller bearing, the EM Series, which combines the strengths and technologies of previous cages into a one-piece steel cage. NSK has achieved a new design involving even newer concepts, while maintaining excellence in function and service life. Our EM series can meet your high load-carrying capacity needs for the new era. EW Series NSK has been supplying a standard cage for smaller-sized, single row cylindrical roller bearings as indicated here: Standard Bearings --- W type (Pressed steel cage with flaps) High Load-Carrying E Type --ET type (Polyamide resin cage) In the 21st century, you can now take advantage of NSK s newly developed cylindrical roller bearing, the EW Series, which combines the strengths and technologies of previous cages into a one-piece steel cage. NSK has achieved a new design involving even newer concepts, while maintaining excellence in function and service life. Our EW series can meet your high load-carrying capacity needs for the new era. 56
ROLLER BEARINGS NU EM Series Bearing Table Cylindrical Roller EM Series NUP NJ Boundary Dimensions Part No. Example NU210 EM C3 Cylindrical roller bearings; NU type; Diameter series 2; Bearing bore 50mm Limiting Basic Load Speeds High Capacity Machined BrassCage Bearing Radial clearance, C3 Abutment and Fillet Dimensions (mm) r r 1 Ratings (N) (min -1 ) Numbers d a d b d c d d D a r a r b Move d D B minmin F w C r C or Grease Oil NU NJ NUP min min max min min max max max S (mm) 25 52 15 1.0 0.6 31.5 29300 27700 13000 16000 NU205EM NJ NUP 30 29 30 34 37 47.0 1.0 0.6 1.2 62 17 1.1 1.1 34.0 41500 37500 10000 13000 NU305EM NJ NUP 31.5 32 32 37 40 55.5 1.0 1.0 1.2 30 62 16 1.0 0.6 37.5 39000 37500 11000 13000 NU206EM NJ NUP 35 34 36 40 44 57.0 1.0 0.6 1.2 72 19 1.1 1.1 40.5 53000 50000 8500 11000 NU306EM NJ NUP 36.5 37 39 44 48 65.5 1.0 1.0 1.2 35 72 17 1.1 0.6 44.0 50500 50000 9500 11000 NU207EM NJ NUP 41.5 39 42 46 50 65.5 1.0 0.6 1.2 80 21 1.5 1.1 46.2 66500 65500 8000 9500 NU307EM NJ NUP 43 42 44 48 53 72.0 1.5 1.0 1.2 40 80 18 1.1 1.1 49.5 55500 55500 8500 10000 NU208EM NJ NUP 46.5 47 48 52 56 73.5 1.0 1.0 1.2 90 23 1.5 1.5 52.0 83000 81500 6700 8500 NU308EM NJ NUP 48 48 50 55 60 82.0 1.5 1.5 1.2 45 85 19 1.1 1.1 54.5 63000 66500 7500 9000 NU209EM NJ NUP 51.5 52 52 57 61 78.5 1.0 1.0 1.2 100 25 1.5 1.5 58.5 97500 98500 6300 7500 NU309EM NJ NUP 53 53 56 60 66 92.0 1.5 1.5 1.4 50 90 20 1.1 1.1 59.5 69000 76500 7100 8500 NU210EM NJ NUP 56.5 57 57 62 67 83.5 1.0 1.0 1.7 110 27 2.0 2.0 65.0 110000 113000 5600 6700 NU310EM NJ NUP 59 59 63 67 73 101.0 2.0 2.0 1.4 55 100 21 1.5 1.1 66.0 86500 98500 6300 7500 NU211EM NJ NUP 63 62 64 68 73 92.0 1.5 1.0 1.2 120 29 2.0 2.0 70.5 137000 143000 5000 6300 NU311EM NJ NUP 64 64 68 72 80 111.0 2.0 2.0 1.4 60 110 22 1.5 1.5 72.0 97500 107000 6000 7100 NU212EM NJ NUP 68 68 70 75 80 102.0 1.5 1.5 1.2 130 31 2.1 2.1 77.0 150000 157000 4800 5600 NU312EM NJ NUP 71 71 75 79 86 119.0 2.0 2.0 1.5 65 120 23 1.5 1.5 78.5 108000 119000 5300 6300 NU213EM NJ NUP 73 73 76 81 87 112.0 1.5 1.5 1.4 140 33 2.1 2.1 82.5 181000 191000 4300 5300 NU313EM NJ NUP 76 76 80 85 93 129.0 2.0 2.0 1.5 Perm. Axial 57
ROLLER BEARINGS Limiting Boundary Dimensions Basic Load Speeds Bearing Abutment and Fillet Dimensions (mm) r r 1 Ratings (N) (min -1 ) Numbers d a d b d c d d D a r a r b Move d D B minmin F w C r C or Grease Oil NU NJ NUP min min max min min max max max S (mm) 70 125 24 1.5 1.5 83.5 119000 137000 5000 6300 NU214EM NJ NUP 78 78 81 86 92 117.0 1.5 1.5 1.4 150 35 2.1 2.1 89.0 205000 222000 4000 5000 NU314EM NJ NUP 81 81 86 92 100 139.0 2.0 2.0 1.5 75 130 25 1.5 1.5 88.5 130000 156000 4800 6000 NU215EM NJ NUP 83 83 86 90 96 122.0 1.5 1.5 1.4 160 37 2.1 2.1 95.0 240000 263000 3800 4800 NU315EM NJ NUP 86 86 92 97 106 149.0 2.0 2.0 1.4 80 140 26 2.0 2.0 95.3 139000 167000 4500 5300 NU216EM NJ NUP 89 89 92 97 104 131.0 2.0 2.0 1.4 170 39 2.1 2.1 101.0 256000 282000 3600 4300 NU316EM NJ NUP 91 91 98 105 114 159.0 2.0 2.0 1.5 85 150 28 2.0 2.0 100.5 167000 199000 4300 5000 NU217EM NJ NUP 94 94 98 104 110 141.0 2.0 2.0 1.3 180 41 3.0 3.0 108.0 291000 330000 3400 4000 NU317EM NJ NUP 98 98 105 110 119 167.0 2.5 2.5 2.0 90 160 30 2.0 2.0 107.0 182000 217000 4000 4800 NU218EM NJ NUP 99 99 104 109 116 151.0 2.0 2.0 1.4 190 43 3.0 3.0 113.5 315000 355000 3200 3800 NU318EM NJ NUP 103 103 111 117 127 177.0 2.5 2.5 1.5 95 170 32 2.1 2.1 112.5 220000 265000 3800 4500 NU219EM NJ NUP 106 106 110 116 123 159.0 2.0 2.0 1.4 200 45 3.0 3.0 121.5 335000 385000 3000 3600 NU319EM NJ NUP 108 108 118 124 134 187.0 2.5 2.5 1.5 100 180 34 2.1 2.1 119.0 249000 305000 3600 4300 NU220EM NJ NUP 111 111 116 122 130 169.0 2.0 2.0 1.4 215 47 3.0 3.0 127.5 380000 425000 2800 3400 NU320EM NJ NUP 113 113 124 132 143 202.0 2.5 2.5 1.8 105 190 36 2.1 2.1 125.0 262000 310000 3400 4000 NU221EM NJ NUP 116 116 121 129 137 179.0 2.0 2.0 1.4 225 49 3.0 3.0 133.0 425000 480000 2600 3200 NU321EM NJ NUP 118 118 131 137 149 212.0 2.5 2.5 1.8 110 200 38 2.1 2.1 132.5 293000 365000 3200 3800 NU222EM NJ NUP 121 121 129 135 144 189.0 2.0 2.0 1.4 200 53 2.1 2.1 132.5 385000 515000 2800 3400 NU2222EM NJ NUP 121 121 129 135 144 189.0 2.0 2.0 1.4 240 50 3.0 3.0 143.0 450000 525000 2600 3000 NU322EM NJ NUP 123 123 139 145 158 227.0 2.5 2.5 3.8 120 215 40 2.1 2.1 143.5 335000 420000 3000 3400 NU224EM NJ NUP 131 131 140 146 156 204.0 2.0 2.0 1.5 215 58 2.1 2.1 143.5 450000 620000 2600 3200 NU2224EM NJ NUP 131 131 140 146 156 204.0 2.0 2.0 2.0 260 55 3.0 3.0 154.0 530000 610000 2200 2800 NU324EM NJ NUP 133 133 150 156 171 247.0 2.5 2.5 1.8 260 86 3.0 3.0 154.0 795000 1030000 2000 2600 NU2324EM NJ NUP 133 133 150 156 171 247.0 2.5 2.5 2.8 130 230 40 3.0 3.0 153.5 365000 455000 2600 3200 NU226EM NJ NUP 143 143 150 158 168 217.0 2.5 2.5 1.5 230 64 3.0 3.0 153.5 530000 735000 2400 3000 NU2226EM NJ NUP 143 143 150 158 168 217.0 2.5 2.5 3.0 280 58 4.0 4.0 167.0 615000 735000 2200 2600 NU326EM NJ NUP 146 146 163 169 184 264.0 3.0 3.0 2.3 280 93 4.0 4.0 167.0 920000 1230000 1900 2400 NU2326EM NJ NUP 146 146 163 169 184 264.0 3.0 3.0 2.3 140 250 42 3.0 3.0 169.0 395000 515000 2400 3000 NU228EM NJ NUP 153 153 165 171 182 237.0 2.5 2.5 1.5 250 68 3.0 3.0 169.0 550000 790000 2200 2800 NU2228EM NJ NUP 153 153 165 171 182 237.0 2.5 2.5 2.5 300 62 4.0 4.0 180.0 665000 795000 2000 2400 NU328EM NJ NUP 156 156 176 182 198 284.0 3.0 3.0 3.3 300 102 4.0 4.0 180.0 1020000 1380000 1700 2200 NU2328EM NJ NUP 156 156 176 182 198 284.0 3.0 3.0 2.8 150 270 45 3.0 3.0 182.0 450000 595000 2200 2800 NU230EM NJ NUP 163 163 177 184 196 257.0 2.5 2.5 1.5 270 73 3.0 3.0 182.0 635000 930000 2000 2600 NU2230EM NJ NUP 163 163 177 184 196 257.0 2.5 2.5 3.0 320 65 4.0 4.0 193.0 760000 920000 1800 2200 NU330EM NJ NUP 166 166 188 195 213 304.0 3.0 3.0 3.2 320 108 4.0 4.0 193.0 1160000 1600000 1600 2000 NU2330EM NJ NUP 166 166 188 195 213 304.0 3.0 3.0 2.2 160 290 48 3.0 3.0 195.0 500000 665000 2200 2600 NU232EM NJ NUP 173 173 190 197 210 277.0 2.5 2.5 1.8 290 80 3.0 3.0 193.0 810000 1190000 1900 2400 NU2232EM NJ NUP 173 173 188 197 210 277.0 2.5 2.5 3.3 340 68 4.0 4.0 204.0 860000 1050000 1700 2000 NU332EM NJ NUP 176 176 199 211 228 324.0 3.0 3.0 3.2 340 114 4.0 4.0 204.0 1310000 1820000 1500 1900 NU2332EM NJ NUP 176 176 199 211 228 324.0 3.0 3.0 2.7 170 310 52 4.0 4.0 207.0 605000 800000 2000 2400 NU234EM NJ NUP 186 186 202 211 223 294.0 3.0 3.0 3.8 310 86 4.0 4.0 205.0 925000 1330000 1800 2200 NU2234EM NJ NUP 186 186 200 211 223 294.0 3.0 3.0 2.8 360 72 4.0 4.0 218.0 930000 1150000 1600 2000 NU334EM NJ NUP 186 186 213 223 241 344.0 3.0 3.0 1.7 360 120 4.0 4.0 216.0 1490000 2070000 1400 1800 NU2334EM NJ NUP 186 186 210 223 241 344.0 3.0 3.0 6.2 180 320 52 4.0 4.0 217.0 625000 850000 1900 2200 NU236EM NJ NUP 196 196 212 221 233 304.0 3.0 3.0 2.2 320 86 4.0 4.0 215.0 1010000 1510000 1700 2000 NU2236EM NJ NUP 196 196 210 221 233 304.0 3.0 3.0 2.7 380 75 4.0 4.0 231.0 985000 1230000 1500 1800 NU336EM NJ NUP 196 196 226 235 255 364.0 3.0 3.0 2.2 380 126 4.0 4.0 227.0 1560000 2220000 1300 1700 NU2336EM NJ NUP 196 196 222 235 255 364.0 3.0 3.0 6.2 190 340 55 4.0 4.0 230.0 695000 955000 1800 2200 NU238EM NJ NUP 206 206 225 234 247 324.0 3.0 3.0 1.7 340 92 4.0 4.0 228.0 1100000 1670000 1600 2000 NU2238EM NJ NUP 206 206 223 234 247 324.0 3.0 3.0 1.7 400 78 5.0 5.0 245.0 1060000 1340000 1400 1700 NU338EM NJ NUP 210 210 240 248 268 380.0 4.0 4.0 1.7 400 132 5.0 5.0 240.0 1770000 2520000 1300 1600 NU2338EM NJ NUP 210 210 235 248 268 380.0 4.0 4.0 6.2 200 360 58 4.0 4.0 243.0 765000 1060000 1700 2000 NU240EM NJ NUP 216 216 238 247 261 344.0 3.0 3.0 2.2 360 98 4.0 4.0 241.0 1220000 1870000 1500 1800 NU2240EM NJ NUP 216 216 235 247 261 344.0 3.0 3.0 2.2 420 80 5.0 5.0 258.0 1140000 1450000 1300 1600 NU340EM NJ NUP 220 220 252 263 283 400.0 4.0 4.0 1.2 420 138 5.0 5.0 253.0 1910000 2760000 1200 1500 NU2340EM NJ NUP 220 220 247 263 283 400.0 4.0 4.0 7.7 The following are also available: (Please contact NSK for details) 1. N and NF type bearings 2. Cages with an outside diameter of less than 650mm 58 EM Series Cylindrical Roller EM Series Perm. Axial
ROLLER BEARINGS EW Series Cylindrical Roller EW Series NU NJ NUP EW Series Bearing Table 305-311 and 205-213 of NU, NJ, NUP Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Perm. Abutment and Fillet Dimensions (mm) Axial r r 1 [N] [kgf] (rpm) Numbers d a d b d c d d D a r a r b Move d D B min min F w C r C or C r C or Grease Oil NU NJ NUP min min max min min max max max S (mm) 25 52 15 1.0 0.6 31.5 29300 27700 2990 2830 12000 14000 NU205EW NU NUP 30.0 29.0 30 34 37 47.0 1.0 0.6 1.2 62 17 1.1 1.1 34.0 41500 37500 4250 3800 10000 12000 NU305EW NU NUP 31.5 31.5 32 37 40 55.5 1.0 1.0 1.2 30 62 16 1.0 0.6 37.5 39000 37500 4000 3800 9500 12000 NU206EW NU NUP 35.0 34.0 36 40 44 57.0 1.0 0.6 1.2 72 19 1.1 1.1 40.5 53000 50000 5400 5100 8500 10000 NU306EW NU NUP 36.5 36.8 39 44 48 65.5 1.0 1.0 1.2 35 72 17 1.1 0.6 44.0 50500 50000 5150 5100 8500 10000 NU207EW NU NUP 41.5 39.0 42 46 50 65.5 1.0 0.6 1.2 80 21 1.5 1.1 46.2 66500 65500 6800 6650 7500 9500 NU307EW NU NUP 43.0 41.5 44 48 53 72.0 1.5 1.0 1.2 40 80 18 1.1 1.1 49.5 55500 55500 5700 5650 7500 9000 NU208EW NU NUP 46.5 46.5 48 52 56 73.5 1.0 1.0 1.2 90 23 1.5 1.5 52.0 83000 81500 8500 8300 6700 8000 NU308EW NU NUP 48.0 48.0 50 55 60 82.0 1.5 1.5 1.2 45 85 19 1.1 1.1 54.5 63000 66500 6450 6800 6700 8000 NU209EW NU NUP 51.5 51.5 52 57 61 78.5 1.0 1.0 1.2 100 25 1.5 1.5 58.5 97500 98500 9950 10000 6000 7500 NU309EW NU NUP 53.0 53.0 56 60 66 92.0 1.5 1.5 1.4 50 90 20 1.1 1.1 59.5 69000 76500 7050 7800 6300 7500 NU210EW NU NUP 56.5 56.5 57 62 67 83.5 1.0 1.0 1.7 110 27 2.0 2.0 65.0 110000 113000 11200 11500 5000 6000 NU310EW NU NUP 59.0 59.0 63 67 73 101.0 2.0 2.0 1.4 55 100 21 1.5 1.1 66.0 86500 98500 8800 10100 5600 7100 NU211EW NU NUP 63.0 61.5 64 68 73 92.0 1.5 1.0 1.2 120 29 2.0 2.0 70.5 137000 143000 14000 14600 4500 5600 NU311EW NU NUP 64.0 64.0 68 72 80 111.0 2.0 2.0 1.4 60 110 22 1.5 1.5 72.0 97500 107000 9950 10900 5300 6300 NU212EW NU NUP 68.0 68.0 70 75 80 102.0 1.5 1.5 1.2 65 120 23 1.5 1.5 78.5 108000 119000 11000 12100 4800 5600 NU213EW NU NUP 73.0 73.0 76 81 87 112.0 1.5 1.5 1.4 59
ROLLER BEARINGS Nomenclature Cylindrical Hyload Series M - Metric Series M 1000, 1200, 1300, 1900, 5200, 5300, 7300 Symbol Description M A I 2 05 GEA X / W101 / C0 M A R SN U Metric series designation Plain cylindrical inner ring Single rib inner ring Short, single rib w/inner ring side plate Double rib inner ring S Metric bore size of next smaller bearing None Standard capacity 6 High capacity series 1 Narrow width 5 Wide width 7 Intermediate width 0 Extra light series 2 Light series 3 Medium series 9 Extra extra light series 05 One-fifth of bore diameter (mm) G GG R RR C D E SN T U A H X M V B Snap ring groove in outer ring O.D. Two snap ring grooves in outer ring O.D. Snap ring groove in outer ring O.D.; snap rings included Two snap ring grooves in outer ring O.D.; snap rings included Plain cylindrical outer ring Single rib outer ring Double rib outer ring Short single rib w/outer ring side plate Outer ring w/two retaining rings in I.D. Single rib outer ring, one retaining ring in I.D. Oversize O.D. outer ring Blind dowel hole in outer ring O.D. Segmented retainer Full complement (no retainer) Formed steel retainer Polymeric retainer omitted if inner ring not furnished omitted if outer ring not furnished 60
ROLLER BEARINGS Nomenclature Cylindrical Hyload Series M - Metric Series M 1000, 1200, 1300, 1900, 5200, 5300, 7300 Symbol Description M A I 2 05 GEA X / W101 / C0 W101 W102 W105 W104 W105 W106 W107 W108 W110 W111 W112 W121 W122 W131 W132 W133 W140 W141 W142 W143 None C2 C0 C3 C4 C5 Cxxx Inner ring bore radius to clear.060" shaft fillet Inner ring bore radius to clear.080" shaft fillet Inner ring bore radius to clear.100" shaft fillet Inner ring bore radius to clear.125" shaft fillet Inner ring bore radius to clear.156" shaft fillet Inner ring bore radius to clear.187" shaft fillet Inner ring bore radius to clear.250" shaft fillet Inner ring with double bore radius, standard shaft fillet radius Outer ring with reduced width tol. Outer ring width.0787" oversize (symmetrical ring) Outer ring width.1575" oversize (symmetrical ring) Outer ring width.0787" oversize and inner ring bore radius clear.060" fillet Outer ring width.1575" oversize and inner ring bore radius clear.156" fillet I.R. bore radius to clear.060" shaft fillet both sides I.R. bore radius to clear.080" shaft fillet both sides I.R. bore radius to clear.100" shaft fillet both sides O.R. snap ring groove on side opposite rib ring O.R. snap ring groove on side opposite rib ring with W131 I.R. O.R. snap ring groove on side opposite rib ring with W132 I.R. O.R. snap ring groove on side opposite rib ring with W133 I.R. Standard commercial clearance Less than basic clearance Basic clearance Greater than basic clearance Greater than C3 clearance Greater than standard clearance(standard for assembly with A outer ring and omitted in model number) Special specific clearance or range - ie/c002 or/c35-49 or C3549 The nomenclature is provided to identify the basic and optional features of bearing and mounted unit assemblies. The most commonly specified variations are listed; however availability of all variations cannot be assumed. Bearing Division should be consulted regarding optional features, availability, and the application requirements. 61
ROLLER BEARINGS Cylindrical Hyload Series M - Metric Fully Crowned Rollers Precision Ground Ribs ContouredRoller Pockets Rollers Individually Separated Optional Full Complement Part Number Example: Prefix Suffix MA7309TV Bearing Number Dimensions Bearing IR OR Dimensions Bearing IR OR ID OD W Number OD ID ID OD W Number OD ID 25 52 15.000 1205 32.166 44.854 65 140 58.738 5313 83.675 121.366 52 20.638 5205 32.166 44.854 70 100 16.000 1914 77.978 92.268 62 17.000 1305 33.972 53.426 110 20.000 1014 80.188 99.906 62 21.000 7305 33.972 53.426 125 24.000 1214 84.772 111.536 62 25.400 5305 33.972 53.426 125 39.688 5214 84.772 111.536 30 62 16.000 1206 38.062 54.074 150 35.000 1314 89.192 129.375 62 23.812 5206 38.062 54.074 150 43.000 7314 89.192 129.375 72 19.000 1306 40.681 60.409 150 63.500 5314 89.192 129.375 72 23.000 7306 40.681 60.409 75 105 16.000 1915 82.931 97.221 72 30.162 5306 40.681 60.409 115 20.000 1015 85.217 104.938 35 72 17.000 1207 43.970 62.471 130 25.000 1215 89.014 115.781 72 26.988 5207 43.970 62.471 130 41.275 5215 89.014 115.781 80 21.000 1307 46.843 67.942 160 37.000 1315 95.920 139.136 80 26.000 7307 46.843 67.942 160 46.000 7315 95.920 139.136 80 34.925 5307 46.843 67.942 160 68.262 5315 95.920 139.136 40 80 18.000 1208 49.929 69.619 80 110 16.000 1916 87.884 102.176 80 30.162 5208 49.929 69.619 125 22.000 1016 91.313 113.088 90 23.000 1308 52.299 77.663 140 26.000 1216 95.286 124.658 90 30.000 7308 52.299 77.663 140 44.450 5216 95.286 124.658 90 36.512 5308 52.299 77.663 170 39.000 1316 101.636 147.424 45 85 19.000 1209 55.519 74.988 170 49.000 7316 101.636 147.424 85 30.162 5209 55.519 74.988 170 68.262 5316 101.636 147.424 100 25.000 1309 59.362 86.103 85 120 18.000 1917 94.615 110.678 100 31.000 7309 59.362 86.103 130 22.000 1017 96.317 118.173 100 39.688 5309 59.362 86.103 150 28.000 1217 102.006 134.216 50 80 16.000 1010 57.882 72.151 150 49.212 5217 102.006 134.216 90 20.000 1210 60.460 79.545 180 41.000 1317 108.522 157.422 90 30.162 5210 60.460 79.545 180 51.000 7317 108.522 157.422 110 27.000 1310 65.146 94.490 180 73.025 5317 108.522 157.422 110 33.000 7310 65.146 94.490 90 125 18.000 1918 99.568 115.636 110 44.450 5310 65.146 94.490 140 24.000 1018 102.362 127.775 55 80 13.000 1911 61.722 73.378 160 30.000 1218 107.218 142.189 90 18.000 1011 64.496 80.531 160 52.388 5218 107.218 142.189 100 21.000 1211 66.901 88.019 190 43.000 1318 114.031 165.407 120 29.000 1311 71.432 103.607 190 54.000 7318 114.031 165.407 120 36.000 7311 71.432 103.607 190 73.025 5318 114.031 165.407 120 49.212 5311 71.432 103.607 95 130 18.000 1919 104.521 120.589 60 85 13.000 1912 66.802 78.461 145 24.000 1019 107.340 132.756 95 18.000 1012 69.499 85.534 170 32.000 1219 113.518 151.242 110 22.000 1212 72.380 97.762 170 55.562 5219 113.518 151.242 110 36.512 5212 72.380 97.762 200 45.000 1319 122.154 173.530 130 31.000 1312 77.551 112.486 200 56.000 7319 122.154 173.530 130 38.000 7312 77.551 112.486 200 77.788 5319 122.154 173.530 130 53.975 5312 77.551 112.486 100 140 20.000 1920 109.995 129.738 65 90 13.000 1913 71.755 83.416 150 24.000 1020 112.344 137.759 100 18.000 1013 74.503 90.541 180 34.000 1220 121.006 161.216 120 23.000 1213 80.421 105.804 180 60.325 5220 121.006 161.216 120 38.100 5213 80.421 105.804 215 47.000 1320 130.165 184.907 140 33.000 1313 83.675 121.366 215 60.000 7320 130.165 184.907 140 40.000 7313 83.675 121.366 215 82.550 5320 130.165 184.907 62
ROLLER BEARINGS High performance in diverse applications with reduced maintenance costs and more compact design HPS Spherical Roller Bearings meet the needs of various equipment for components with reduced costs and unsurpassed functionality. By taking full advantage of NSK s wealth of experience and expertise, HPS spherical roller bearings realize unprecedented endurance and high limiting speeds to support downsizing while at the same time improving performance and lengthening equipment operating life. Long Life Lower maintenance cost Spherical Roller HPS LIFE 2 times the operating life (maximum) LIMITING SPEED 20% higher (maximum) Maintenance costs are an important factor in reducing total equipment costs. HPS spherical roller bearings realize twice the operating life of conventional products, and longer operating life leads to lower maintenance costs. Flexible Applicable to a variety of applications With extremely high limiting speed and high-strength cage, HPS spherical roller bearings deliver high performance to a variety of applications. Compact Contributing to equipment downsizing Achieving longer operating life can be realized together with the selection of smaller bearings. HPS spherical roller bearings encourage compact design for various equipment, thereby supporting the demand for downsizing. Innovative design developed through enhanced structural analysis Technology The HPS cage incorporates a roller guide function in place of a guide ring. Eliminating the guide ring and optimizing the design of the inner and outer ring configuration facilitates the placement of additional, larger rollers. Optimized design for the internal specifications and improved press technology greatly increase load capacity, and realize longer life. Special surface treatment further strengthens the cage, reducing wear, heat and friction; it also allows for higher limiting speeds. Adoption of state-of-the-art materials HPS spherical roller bearings are made from NSK s high cleanliness Z steel. This steel features greater fatigue strength. In addition, special surface treatment makes it more resistant to wear and more durable in a variety of applications. NSK old type bearing HPS Cage design features stronger resistance to wear By utilizing the space gained from eliminating the guide ring and improving the design through advanced structural analysis, cage strength has been increased dramatically. The high-precision roller guide function in place of the guide ring, united with a special surface treatment, strengthens the cage against wear and increases the limiting speeds. 63
ROLLER BEARINGS Spherical Roller HPS Dynamic Equivalent Load P = XFr + YFa F a / F r < e Fa / F r > e X Y X Y 1 Y 3 0.067 Y 2 Static Equivalent Load P0 = Fr + Y0Fa The values for e,y2,y3 and Y0 are given in the table below. Dimensions (mm) Basic Load Rating Limiting Speeds (min -1 ) Bearing Numbers Abutment and Fillet Dimensions (mm) Constant Axial Load Factor Mass r N Cylindrical Tapered da Da ra Approx d D B (min) Cr Cor Grease Oil Bore Bore ( 1 ) min max max min max e Y2 Y3 Y0 kg 40 80 23 1.1 113000 99500 6700 8500 22208EAE4 22208EAKE4 47 49 73 70 1.0 0.28 3.6 2.4 2.4 0.50 90 23 1.5 118000 111000 6000 7500 21308EAE4 21308EAKE4 49 54 81 75 1.5 0.25 3.9 2.7 2.6 0.73 90 33 1.5 170000 153000 5300 6700 22308EAE4 22308EAKE4 49 52 81 77 1.5 0.35 2.8 1.9 1.9 0.98 45 85 23 1.1 118000 111000 6000 7500 22209EAE4 22209EAKE4 52 54 78 75 1.0 0.25 3.9 2.7 2.6 0.55 100 25 1.5 149000 144000 5000 6300 21309EAE4 21309EAKE4 54 65 91 89 1.5 0.23 4.3 2.9 2.8 0.96 100 36 1.5 207000 195000 4500 5600 22309EAE4 22309EAKE4 54 59 91 86 1.5 0.34 2.9 2.0 1.9 1.34 50 90 23 1.1 124000 119000 5600 7100 22210EAE4 22210EAKE4 57 60 83 81 1.0 0.24 4.3 2.9 2.8 0.61 110 27 2.0 178000 174000 4500 5600 21310EAE4 21310EAKE4 60 72 100 98 2.0 0.23 4.4 3.0 2.9 1.21 110 40 2.0 246000 234000 4300 5300 22310EAE4 22310EAKE4 60 64 100 93 2.0 0.35 2.8 1.9 1.9 1.78 55 100 25 1.5 149000 144000 5300 6700 22211EAE4 22211EAKE4 64 65 91 89 1.5 0.23 4.3 2.9 2.8 0.81 120 29 2.0 178000 174000 4500 5600 21311EAE4 21311EAKE4 65 72 110 98 2.0 0.23 4.4 3.0 2.9 1.58 120 43 2.0 292000 292000 3800 4800 22311EAE4 22311EAKE4 65 73 110 103 2.0 0.34 2.9 2.0 1.9 2.30 60 110 28 1.5 178000 174000 4800 6000 22212EAE4 22212EAKE4 69 72 101 98 1.5 0.23 4.4 3.0 2.9 1.10 130 31 2.1 238000 244000 3800 4800 21312EAE4 21312EAKE4 72 87 118 117 2.0 0.22 4.5 3.0 3.0 1.98 130 46 2.1 340000 340000 3600 4500 22312EAE4 22312EAKE4 72 79 118 111 2.0 0.34 3.0 2.0 1.9 2.89 65 120 31 1.5 221000 230000 4300 5300 22213EAE4 22213EAKE4 74 80 111 107 1.5 0.24 4.2 2.8 2.7 1.51 140 33 2.1 264000 275000 3600 4500 21313EAE4 21313EAKE4 77 94 128 126 2.0 0.22 4.6 3.1 3.0 2.45 140 48 2.1 375000 380000 3200 4000 22313EAE4 22313EAKE4 77 84 128 119 2.0 0.33 3.0 2.0 2.0 3.52 70 125 31 1.5 225000 232000 4000 5300 22214EAE4 22214EAKE4 79 84 116 111 1.5 0.23 4.3 2.9 2.8 1.58 150 35 2.1 310000 325000 3200 4000 21314EAE4 21314EAKE4 82 101 138 135 2.0 0.22 4.6 3.1 3.0 3.00 150 51 2.1 425000 435000 3000 3800 22314EAE4 22314EAKE4 82 91 138 129 2.0 0.33 3.0 2.0 2.0 4.28 75 130 31 1.5 238000 244000 4000 5000 22215EAE4 22215EAKE4 84 87 121 117 1.5 0.22 4.5 3.0 3.0 1.64 160 37 2.1 310000 325000 3200 4000 21315EAE4 21315EAKE4 87 101 148 134 2.0 0.22 4.6 3.1 3.0 3.64 160 55 2.1 485000 505000 2800 3600 22315EAE4 22315EAKE4 87 97 148 137 2.0 0.33 3.0 2.0 2.0 5.26 80 140 33 2.0 264000 275000 3600 4500 22216EAE4 22216EAKE4 90 94 130 126 2.0 0.22 4.6 3.1 3.0 2.01 170 39 2.1 355000 375000 3000 3800 21316EAE4 21316EAKE4 92 109 158 146 2.0 0.23 4.4 3.0 2.9 4.32 170 58 2.1 540000 565000 2600 3400 22316EAE4 22316EAKE4 92 103 158 145 2.0 0.33 3.0 2.0 2.0 6.23 85 150 36 2.0 310000 325000 3400 4300 22217EAE4 22217EAKE4 95 101 140 135 2.0 0.22 4.6 3.1 3.0 2.54 180 41 3.0 360000 395000 3000 4000 21317EAE4 21317EAKE4 99 108 166 142 2.5 0.24 4.3 2.9 2.8 5.20 180 60 3.0 600000 630000 2400 3200 22317EAE4 22317EAKE4 99 110 166 155 2.5 0.33 3.1 2.1 2.0 7.23 90 160 40 2.0 360000 395000 3200 4000 22218EAE4 22218EAKE4 100 108 150 142 2.0 0.24 4.3 2.9 2.8 3.30 190 43 3.0 415000 450000 2800 3600 21318EAE4 21318EAKE4 104 115 176 152 2.5 0.24 4.3 2.9 2.8 6.10 190 64 3.0 665000 705000 2400 3000 22318EAE4 22318EAKE4 104 115 176 163 2.5 0.33 3.1 2.1 2.0 8.56 95 170 43 2.1 415000 450000 3000 3800 22219EAE4 22219EAKE4 107 115 158 152 2.0 0.24 4.3 2.9 2.8 4.04 200 67 3.0 735000 780000 2200 2800 22319EAE4 22319EAKE4 109 121 186 172 2.5 0.33 3.1 2.1 2.0 9.91 100 180 46 2.1 455000 490000 2800 3600 22220EAE4 22220EAKE4 112 119 168 160 2.0 0.24 4.3 2.9 2.8 4.84 215 73 3.0 860000 930000 2000 2600 22320EAE4 22320EAKE4 114 130 201 184 2.5 0.33 3.0 2.0 2.0 12.70 110 200 53 2.1 605000 645000 2600 3200 22222EAE4 22222EAKE4 122 129 188 178 2.0 0.25 4.0 2.7 2.6 6.99 240 80 3.0 1030000 1120000 1900 2400 22322EAE4 22322EAKE4 124 145 226 206 2.5 0.33 3.1 2.1 2.0 17.60 120 215 58 2.1 685000 765000 2400 3000 22224EAE4 22224EAKE4 132 142 203 190 2.0 0.25 3.9 2.7 2.6 8.80 260 86 3.0 1190000 1320000 1700 2200 22324EAE4 22324EAKE4 134 157 246 222 2.5 0.32 3.1 2.1 2.0 22.20 130 230 64 3.0 820000 940000 2200 2600 22226EAE4 22226EAKE4 144 152 216 204 2.5 0.26 3.8 2.6 2.5 11.00 Note ( 1 ) The suffix K indicates that the bearing has a tapered bore (taper 1:12). Remarks 1. The maximum operating temperature of standard HPS spherical roller bearings is 200 o C. 2. The suffix E4 indicates that the bearing has an oil groove and holes. 64
ROLLER BEARINGS Spherical Roller Double Row Spherical roller bearings feature a large load rating capacity and self-aligning capability. This type of bearing is suitable for low or medium speed applications which involve heavy or impact loading. Bearings with a tapered bore can be fitted and removed easily using an adapter assembly or withdrawal sleeve. The rate of taper is equivalent among all bearing series. 240 and 241 series... 1:30 (supplementary code K30 ) Others... 1:12 (supplementary code K ) Common suffixes used with basic bearing number. C3... Internal clearance greater than standard. C4... Internal clearance greater than C3. E4... Lubrication groove and three equally spaced holes in outer ring. Cage Materials are indicated by suffix: CAM - Brass Cage C, CD & EA - Steel Cage Standard Spherical Roller Design Manufacturer Bearing Type NSK KOYO NSK KOYO NSK KOYO EA, C & CD RH M R CAM RHA Inner Ring Central Integral Flange and Side Flange Side Flanges Roller Symmetrical Symmetrical Symmetrical Roller Guide Cage - Piloted Central Integral Flange Guide Ring Cage Two Piece Press Steel One Piece Brass One Piece Brass SKF FAG CC - - MB CA EAM Torrington CJ SD YM 65
ROLLER BEARINGS Cylindrical Bore Tapered Bore Dimensions Basic Bearing No. ID OD W Cylindrical Tapered Bore Bore 25 52 18 22205 22205K 62 17 21305 21305K 30 62 20 22206 22206K 72 19 21306 21306K 35 72 23 22207 22207K 80 21 21307 21307K 80 31 22307 22307K 40 80 23 22208 22208K 90 23 21308 21308K 90 33 22308 22308K 45 85 23 22209 22209K 100 25 21309 21309K 100 36 22309 22309K 50 90 23 22210 22210K 110 27 21310 21310K 110 40 22310 22310K 55 100 25 22211 22211K 120 29 21311 21311K 120 43 22311 22311K 60 110 28 22212 22212K 130 31 21312 21312K 130 46 22312 22312K 65 120 31 22213 22213K 140 33 21313 21313K 140 48 22313 22313K 70 125 31 22214 22214K 150 35 21314 21314K 150 51 22314 22314K 75 130 31 22215 22215K 160 37 21315 21315K 160 55 22315 22315K 80 140 33 22216 22216K 170 39 21316 21316K 170 58 22316 22316K 85 150 36 22217 22217K 180 41 21317 21317K 180 60 22317 22317K 90 160 40 22218 22218K 160 52 23218 23218K 190 43 21318 21318K 190 64 22318 22318K 95 170 43 22219 22219K 200 45 21319 21319K 200 67 22319 22319K 100 165 52 23120 23120K 180 46 22220 22220K 180 60 23220 23220K 215 47 21320 21320K 215 73 22320 22320K 110 170 45 23022 23022K 180 56 23122 23122K 180 69 24122 24122K30 200 53 22222 22222K 200 70 23222 23222K 240 50 21322 21322K Dimensions Basic Bearing No. ID OD W Cylindrical Tapered Bore Bore 110 240 80 22322 22322K 120 180 46 23024 23024K 180 60 24024 24024K30 200 62 23124 23124K 200 80 24124 24124K30 215 58 22224 22224K 215 76 23224 23224K 260 86 22324 22324K 130 200 52 23026 23026K 200 69 24026 24026K30 210 64 23126 23126K 210 80 24126 24126K30 230 64 22226 22226K 230 80 23226 23226K 280 93 22326 22326K 140 210 53 23028 23028K 210 69 24028 24028K30 225 68 23128 23128K 225 85 24128 24128K30 250 68 22228 22228K 250 88 23228 23228K 300 102 22328 22328K 150 210 45 23930 23930K 225 56 23030 23030K 225 75 24030 24030K30 250 80 23130 23130K 250 100 24130 24130K30 270 73 22230 22230K 270 96 23230 23230K 320 108 22330 22330K 160 220 45 23932 23932K 240 60 23032 23032K 240 80 24032 24032K30 270 86 23132 23132K 270 109 24132 24132K30 290 80 22232 22232K 290 104 23232 23232K 340 114 22332 22332K 170 230 45 23934 23934K 260 67 23034 23034K 260 90 24034 24034K30 280 88 23134 23134K 280 109 24134 24134K30 310 86 22234 22234K 310 110 23234 23234K 360 120 22334 22334K 180 250 52 23936 23936K 280 74 23036 23036K 280 100 24036 24036K30 300 96 23136 23136K 300 118 24136 24136K30 320 86 22236 22236K 320 112 23236 23236K 380 126 22336 22336K 190 260 52 23938 23938K Spherical Roller Double Row Dimensions Basic Bearing No. ID OD W Cylindrical Tapered Bore Bore 190 290 75 23038 23038K 290 100 24038 24038K30 320 104 23138 23138K 320 128 24138 24138K30 340 92 22238 22238K 340 120 23238 23238K 400 132 22338 22338K 200 280 60 23940 23940K 310 82 23040 23040K 310 109 24040 24040K30 340 112 23140 23140K 340 140 24140 24140K30 360 98 22240 22240K 360 128 23240 23240K 420 138 22340 22340K 220 300 60 23944 23944K 340 90 23044 23044K 340 118 24044 24044K30 370 120 23144 23144K 370 150 24144 24144K30 400 108 22244 22244K 400 144 23244 23244K 460 145 22344 22344K 240 320 60 23948 23948K 360 92 23048 23048K 360 118 24048 24048K30 400 128 23148 23148K 400 160 24148 24148K30 440 120 22248 22248K 440 160 23248 23248K 500 155 22348 22348K 260 360 75 23952 23952K 400 104 23052 23052K 400 140 24052 24052K30 440 144 23152 23152K 440 180 24152 24152K30 480 130 22252 22252K 480 174 23252 23252K 540 165 22352 22352K 280 380 75 23956 23956K 420 106 23056 23056K 420 140 24056 24056K30 460 146 23156 23156K 460 180 24156 24156K30 500 130 22256 22256K 500 176 23256 23256K 580 175 22356 22356K 300 420 90 23960 23960K 460 118 23060 23060K 460 160 24060 24060K30 500 160 23160 23160K 500 200 24160 24160K30 540 140 22260 22260K 540 192 23260 23260K 620 185 22360 22360K 66
ROLLER BEARINGS Features of Vibrating Equipment Bearings Spherical Roller Double Row - Vibrating Screen Bearings Identified by the U15 Suffix Have a reduced OD tolerance held to the middle half of Class 0 specifications to provide more accurate control of housing fit. Have a reduced bore tolerance held to the upper half of Class 0 specification to provide adequate clearance for loose fitted inner rings, while at the same time reducing excessive slippage and galling. Bearings for vibrating applications such as screens, feeders and compactors must tolerate very severe operating conditions. After many years of research and analysis, NSK has developed modified self-aligning spherical roller bearings to accommodate the high loads and static and dynamic misalignment characteristic of this equipment. Features incorporated in the NSK vibrating mechanism design include - VS features and U15 features. Bearings Identified by the - VS Suffix Supplied with special surface finishes to ensure smooth operation and low running temperatures. Specially heat treated to increase shock loading capabilities. Have internal clearances held to the top two-thirds of the specified clearance to precisely control load distribution and heat generation. Available in C3/C4 clearance range. Features of CAM-VS Type Bearings CA series bearings have high load capacity, superior durability, and wear resistance featuring brass cage and larger rollers than that of the conventional M series. The CA series is available in a wide selection of sizes and other specifications, such as bearings with a lubrication hole and groove provided in the outer ring (E4), high heat-resistant bearings capable of withstanding up to 200 o C (S11), and high-precision bearings (P55), for various types of large rolls. Dimensions (mm) Bearing ID OD W Number 40 90 33 22308CAME4U15-VS 45 100 36 22309CAME4U15-VS 50 110 40 22310CAME4U15-VS 55 120 43 22311CAME4U15-VS 60 130 46 22312CAME4U15-VS 65 140 48 22313CAME4U15-VS 70 150 51 22314CAME4U15-VS 75 160 55 22315CAME4U15-VS 80 170 58 22316CAME4U15-VS 85 180 60 22317CAME4U15-VS 90 190 64 22318CAME4U15-VS 95 200 67 22319CAME4U15-VS 100 215 73 22320CAME4U15-VS 110 240 80 22322CAME4U15-VS 120 260 86 22324CAME4U15-VS 130 280 93 22326CAME4U15-VS 140 300 102 22328CAME4U15-VS 150 320 108 22330CAME4U15-VS 160 340 114 22332CAME4U15-VS 170 360 120 22334CAME4U15-VS 180 380 125 22336CAME4U15-VS 190 400 132 22338CAME4U15-VS 200 420 138 22340CAME4U15-VS 67
ROLLER BEARINGS Procedure for Mounting Spherical Roller Bearings with Tapered Bore and using an Adapter Sleeve Spherical Roller Mounting Procedure 1 Unwrap bearing and inspect for internal clearance group. When supplied with housings they will usually be Normal Clearance - no suffix after number - or, C3 Clearance one group greater than normal. Multiply last two numerals of bearing number by 5 to determine nominal bore size in millimetres. Example: 22232 = 32 x 5 = 160mm Nominal Bore (bearing bore) 2 Measure bearing with feeler gauges and note actual internal clearance. Two rollers should be lined up side by side at top of the bearing and progressively larger feelers slid between rollers and outer race until beginning of interference is felt. Under no circumstances should bearing be rotated to roll feelers through - this will result in an erroneous reading. 3 From Actual Clearance measured, subtract Decrease in Radial Clearance from column B of TABLE 1 below to obtain required Residual Clearance. Example : 22232KC3 is measured at.230mm actual clearance which falls within the I.S.O. standard actual clearance range of.180 to.230mm. The Decrease in Radial Clearance for 22232KC3 column reads.075 to.100mm. Therefore the Residual Clearance range, which is what the bearing should measure within after tightening adapter, is :- Max = (.230 -.075) =.155mm and Min = (.230 -.100) =.130mm. 7 When bearings are in position, the adapter sleeves can be tightened. Fixed bearing should be tightened first, C spanners should be used where possible. Progressively, tighten locknut whilst feeler gauge readings are taken to achieve desired Residual Clearance. 8 The floating bearing should be positioned slightly off housing centre toward locknut side of sleeve so that as nut is tightened, bearing will be displaced approximately back to centre line. No spacer rings are used. 9 Grease should be worked into bearing for as much of circumference as possible, rotating occasionally. Basic grease capacity rule is that 1/2-1/3 of housing volumetric capacity be filled. This can be done by hand prior to fitting cap which can be plugged and only the taconite seals lubricated via nipples on a regular basis. High temperature or unusual applications may require a special grease selection and should be referred to your nearest branch. SUITABLE LUBRICANTS: Shell - ALvania R2, EP2 BP - Energrease LS2, LSEP2 Mobil - Grease 77, Mobilux EP2 Ampol - RRs, EP Grease C2 Caltex - Regal, Starfak, Premium 2 4 Bearings should be located or fixed in one housing and allowed to float in the other. Therefore, spacer rings will be used in one housing only. One or two spacer rings are used according to bearing size. If one is used, it should be located on locknut size. If two, they should be positioned each side of bearing. Two types of spacer rings commonly used are Solid (fully circular) and Gap types. 10 Housing cap, after cleaning, can be assembled to bodies (not interchangeable). Feeler gauge should be tried between housing base and frame pad to ensure flatness and that shims are not required. Base bolts can be tightened. Check that rotation is free and not impaired. Taconite seals should be fitted. Adjust housing base alignment to allow constant clearance around circumference of rotating labyrinth and taconite cover body. Seals should be lubricated until grease extrudes fully around labyrinth circumference. DO NOT overgrease bearing housing as damage and overheating can occur during initial running period. 5 Bearings, adapter sleeves, rotating seal components and solid spacer rings should be fitted loosely to shaft in approximately required positions. The taconite seals (with outer casting) can be positioned already assembled. Otherwise, rotating labyrinth and oil seal can be positioned loosely. 6 After cleaning, set up bases in position. Fit base bolts (if on base frame) but leave loose so that bases can be moved later to provide correct shaft alignment. Lower bearings and shaft assembly into position carefully, re-spacing components as required. TABLE 1. Standard Tolerance Values A B C D Bearing bore Decrease in Axial displacement Min. permissible diameter rad1al internal residual d clearance Taper 1:12 clearance over incl. min max min max Normal C3 30 40 0.020 0.025 0.35 0.4 0.015 0.025 40 50 0.025 0.030 0.4 0.45 0.020 0.030 50 65 0.030 0.040 0.45 0.6 0.025 0.035 65 80 0.040 0.050 0.6 0.75 0.025 0.040 80 100 0.045 0.060 0.7 0.9 0.035 0.050 100 120 0.050 0.070 0.75 1.1 0.050 0.065 120 140 0.065 0.090 1.1 1.4 0.055 0.080 140 160 0.075 0.100 1.2 1.6 0.055 0.090 160 180 0.080 0.110 1.3 1.7 0.060 0.100 180 200 0.090 0.130 1.4 2.0 0.070 0.100 200 225 0.100 0.140 1.6 2.2 0.080 0.120 225 250 0.110 0.150 1.7 2.4 0.090 0.130 250 280 0.120 0.170 1.9 2.7 0.100 0.140 280 315 0.130 0.190 2.0 3.0 0.110 0.150 315 355 0.150 0.210 2.4 3.3 0.120 0.170 355 400 0.170 0.230 2.6 3.6 0.130 0.190 400 450 0.200 0.260 3.1 4.0 0.130 0.200 450 500 0.210 0.280 3.3 4.4 0.160 0.230 500 560 0.240 0.320 3.7 5.0 0.170 0.250 560 630 0.260 0.350 4.0 5.4 0.200 0.290 630 710 0.300 0.400 4.6 6.2 0.210 0.310 710 800 0.340 0.450 5.3 7.0 0.230 0.350 68
ROLLER BEARINGS 69 Spherical Roller Interchange Table Interchange Table - Spherical Roller Bearings for Vibrating Equipment FAG 22308ET41A 22309ET41A 22310ET41A 22311ET41A 22312ET41A 22313ET41A 22314ET41A 22315ET41A 22316ET41A 22317ET41A 22318ET41A 22319ET41A 22320ET41A 22322ET41A 22324ET41A 22326ET41A 22328ET41A 22330ET41A 22332ET41A 22334ET41A 22336ET41A 22338ET41A 22340ET41A SKF 22308CCJA/W33VA405 22309CCJA/W33VA405 22310CCJA/W33VA405 22311CCJA/W33VA405 22312CCJA/W33VA405 22313CCJA/W33VA405 22314CCJA/W33VA405 22315CCJA/W33VA405 22316CCJA/W33VA405 22317CCJA/W33VA405 22318CCJA/W33VA405 22319CCJA/W33VA405 22320CCJA/W33VA405 22322CCJA/W33VA405 22324CCJA/W33VA405 22326CCJA/W33VA405 22328CCJA/W33VA405 22330CCJA/W33VA405 22332CCJA/W33VA405 22334CCJA/W33VA405 22336CCJA/W33VA405 22338CCJA/W33VA405 22340CCJA/W33VA405 TORRINGTON 22308VCFW33C4 22309VCFW33C4 22310VCFW33C4 22311YMW33W800C4 22312YMW33W800C4 22313YMW33W800C4 22314YMW33W800C4 22315YMW33W800C4 22316YMW33W800C4 22317YMW33W800C4 22318YMW33W800C4 22319YMW33W800C4 22320YMW33W800C4 22322YMW33W800C4 22324YMW33W800C4 22326YMW33W800C4 22328YMW33W800C4 22330YMW33W800C4 22332YMW33W800C4 22334W33W800C4 22336W33W800C4 22338W33W800C4 22340W33W800C4 KOYO 22308UAD1L1VS-PX2 22309UAD1L1VS-PX2 22310UAD1L1VS-PX2 22311UAD1L1VS-PX2 22312UAD1L1VS-PX2 22313UAD1L1VS-PX2 22314UAD1L1VS-PX2 22315UAD1L1VS-PX2 22316UAD1L1VS-PX2 22317UAD1L1VS-PX2 22318UAD1L1VS-PX2 22319UAD1L1VS-PX2 22320UAD1L1VS-PX2 22322UAD1L1VS-PX2 22324UAD1L1VS-PX2 22326UAD1L1VS-PX2 22328UAD1L1VS-PX2 22330UAD1L1VS-PX2 22332UAD1L1VS-PX2 22334UAD1L1VS-PX2 22336UAD1L1VS-PX2 22338UAD1L1VS-PX2 22340UAD1L1VS-PX2 NTN 22308ROVSW502-C4FY 22309ROVSW502-C4FY 22310ROVSW502-C4FY 22311ROVSW502-C4FY 22312ROVSW502-C4FY 22313ROVSW502-C4FY 22314ROVSW502-C4FY 22315ROVSW502-C4FY 22316ROVSW502-C4FY 22317ROVSW502-C4FY 22318ROVSW502-C4FY 22319ROVSW502-C4FY 22320ROVSW502-C4FY 22322ROVSW502-C4FY 22324ROVSW502-C4FY 22326ROVSW502-C4FY 22328ROVSW502-C4FY 22330ROVSW502-C4FY 22332ROVSW502-C4FY 22334ROVSW502-C4FY 22336ROVSW502-C4FY 22338ROVSW502-C4FY 22340ROVSW502-C4FY NSK 22308CAME4C4U15-VS 22309CAME4C4U15-VS 22310CAME4C4U15-VS 22311CAME4C4U15-VS 22312CAME4C4U15-VS 22313CAME4C4U15-VS 22314CAME4C4U15-VS 22315CAME4C4U15-VS 22316CAME4C4U15-VS 22317CAME4C4U15-VS 22318CAME4C4U15-VS 22319CAME4C4U15-VS 22320CAME4C4U15-VS 22322CAME4C4U15-VS 22324CAME4C4U15-VS 22326CAME4C4U15-VS 22328CAME4C4U15-VS 22330CAME4C4U15-VS 22332CAME4C4U15-VS 22334CAME4C4U15-VS 22336CAME4C4U15-VS 22338CAME4C4U15-VS 22340CAME4C4U15-VS
ROLLER BEARINGS Spherical Thrust Metric Dimensions (mm) Bearing ID OD W Number 60 130 42 29412 65 140 45 29412 70 150 48 29414 75 160 51 29415 80 170 54 29416 85 150 39 29317 180 58 29417 90 155 39 29318 190 60 29418 100 170 42 29320 210 67 29420 110 190 48 29322 230 73 29422 120 210 54 29324 250 78 29424 130 225 58 29326 270 85 29426 140 240 60 29328 280 85 29428 150 250 60 29330 300 90 29430 160 270 67 29332 320 95 29432 170 280 67 29334 340 103 29434 180 300 73 29336 360 109 29436 190 320 78 29338 380 115 29438 200 280 48 29240 340 85 29340 400 122 29440 220 300 48 29244 360 85 29344 420 122 29444 240 340 60 29248 380 85 29348 440 122 29448 Dimensions (mm) Bearing ID OD W Number 260 360 60 29252 420 95 29352 480 132 29452 280 380 60 29256 440 95 29356 520 145 29456 300 420 73 29260 480 109 29360 540 145 29460 320 440 73 29264 500 109 29364 580 155 29464 340 460 73 29268 540 122 29368 620 170 29468 360 500 85 29272 560 122 29372 640 170 29472 380 520 85 29276 600 132 29376 670 175 29476 400 540 85 29280 620 132 29380 710 185 29480 420 580 95 29284 650 140 29384 730 185 29484 440 600 95 29288 680 145 29388 780 206 29488 460 620 95 29292 710 150 29392 800 206 29492 480 650 103 29296 730 150 29396 850 224 29496 500 670 103 292/500 750 150 293/500 870 224 294/500 If the product you need is not listed, please contact your local branch. 70
Ball Bearing Units WIR Housing Summary... 163 NSK 200 Series... 163 WIR Bearing Summary... 164 Pillow Blocks: Cast Iron... 165 UCP 200... 165 UCP X00, UCP300... 166 UCP 300... 167 UKP 200... 168 UKP X00... 169 UKP 300... 170 UELP 200... 171 Pillow Blocks: Normal Duty... 172 UCSB2... 172 UKSB2... 173 UCSBX... 174 UKSBX... 175 Pillow Blocks: Short Base... 176 UCUP 200... 176 Pillow Blocks: Pressed Steel... 177 PB, RPB... 177 PBS... 178 Flanged: 4 Bolt Square... 179 Cast Iron: UCF 200... 179 Cast Iron: UCF X00... 180 Cast Iron: UCF 300... 181 Cast Iron: UKF 200... 182 Cast Iron: UKF 300... 183 Cast Iron: UELF 200... 184 Cast Iron: UCFC 200... 185 Cast Iron: UCFC X00... 186 Cast Iron: UKFC 200... 187 Flanged: Pressed Metal... 188 MST, MS... 188 Flanged: 2 Bolt Hole... 189 Cast Iron: UCFL 200... 189 Cast Iron: UKFL 200... 190 Cast Iron: FD 200... 191 Special Flanged Units... 192 UCFA 200... 192 UCFH 200... 193 161
Ball Bearing Units Take Up: Cast Iron... 194 UCT 200... 194 UELT 200... 195 UKT 200... 196 Take Up: Pressed Metal... 197 MSTU... 197 Hanger Unit: Cast Iron... 198 UCHB 200... 198 Cartridge Type: Cast Iron... 199 UCC2... 199 UKC2... 200 Housed Bearing Inserts... 201 Selection Guide... 201 Inserts: Spherical O/D... 202 UC2... 202 UCX... 203 UC3... 204 AS2... 205 UEL2... 206 AEL2... 207 UK2... 208 UKX... 209 UK3... 210 Inserts: Parallel O/D... 211 UCS2... 211 AELS2... 212 Silver Lube... 213 Series PNP, PSF, PSFT... 214 Housings... 215 Bearing Inserts... 218 162
BALL BRG UNITS Shaft Diameter inch mm Bearing Series WIR Housing Summary NSK 200 Series NSK 200 Series Wide Re-greasable Units 12.000 201 P203 1/2 12.700 9/16 14.288 15.000 202 P203 5/8 15.875 17.000 203 P203 11/16 17.462 3/4 19.050 204 P204 UP204 T204 F204 FC204 FL204 FA204 HB204 C204 FH204 20.000 13/16 20.638 7/8 22.225 15/16 23.812 205 P205 SB205 UP205 T205 F205 FC205 FL205 FA205 HB205 C205 FH205 25.000 1 25.400 1-1/16 26.988 1-1/8 28.575 30.000 206 P206 SB206 UP206 T206 F206 FC206 FL206 FA206 HB206 C206 FH206 1-3/16 30.162 1-1/4 31.750 1-1/4 31.750 1-5/16 33.338 1-3/8 34.925 207 P207 SB207 UP207 T207 F207 FC207 FL207 FA207 HB207 C207 FH207 35.000 1-7/16 36.512 1-7/16 36.512 1-1/2 38.100 208 P208 SB208 UP208 T208 F208 FC208 FL208 FA208 HB208 C208 FH208 1-9/16 39.688 40.000 1-5/8 41.275 1-11/16 42.862 209 P209 SB209 UP209 T209 F209 FC209 FL209 FA209 HB209 C209 FH209 1-3/4 44.450 45.000 1-13/16 46.038 1-7/8 47.625 1-15/16 49.212 210 P210 SB210 UP210 T210 F210 FC210 FL210 FA210 HB210 C210 50.000 2 50.800 2 50.800 2-1/16 52.388 2-1/8 53.975 211 P211 SB211 T211 F211 FC211 FL211 FA211 HB211 C211 55.000 2-3/16 55.562 2-1/4 57.150 2-5/16 58.738 212 P212 SB212 T212 F212 FC212 FL212 HB212 C212 60.000 2-3/8 60.325 2-7/16 61.912 2-1/2 63.500 213 P213 SB213 T213 F213 FC213 FL213 C213 65.000 2-5/8 66.675 2-11/16 68.262 214 P214 SB214 T214 F214 FC214 2-3/4 69.850 70.000 2-13/16 71.438 2-7/8 73.025 2-15/16 74.612 215 P215 SB215 T215 F215 FC215 75.000 3 76.200 3-1/8 79.375 80.000 216 P216 SB216 T216 F216 3-3/16 80.962 3-1/4 82.550 217 P217 SB217 T217 F217 85.000 3-7/16 87.312 3-1/2 88.900 218 P218 SB218 F218 FC218 Additional Housing Seal Pressed Steel Cast Cover Type Temperature Ranges for Mounted Ball Bearing Units Temperature Ranges for Ball Bearing Units Symbol Temperature Range C Radial Clearance of Bearing Enclosed Grease Thickener Basic Oil Type Material Standard - -10 to +110 Normal Lithium Mineral Soap Oil Coldproof T1-50 to +110 Normal Lithium Diester Soap Oil Lithium Semi- Mineral T2-10 to +120 C3 Complex Heatproof Oil Soap Heatproof T3-30 to +160 C4 Lithium Silicone Oil Seal Contact Nitrite Rubber Labyrinth Steel Plate Heat Contact Resistant Rubber Labyrinth Steel Plate Recommended Replenishing Interval and Operating Temperature Operating Temperature C F Up to 70 Up to 158 Recommended Replenishing Interval Bearing Type - Standard 70 100 158 212 6 Months Standard 100 120 212 248 3 Months Semi-Heatproof 120 150 248 302 0.5 Months Heatproof 2-3 Shots Maximum 163
BALL BRG UNITS WIR Bearing Summary NSK 200 Series NSK -RHP 200 Wide Series Re-greasable Insert Bearings (Superior Seals) NSK RHP RHP(T) NSK Metal Flinger Standard (200) Standard (1000) Triple Lip Seal (1000) Shaft NSK Wide 200 Series Adaptor RHP Wide 200 Series F/Outer Ring Diameter Sleeve inch mm (Use with UK Bearing) (T) (T) Set Screw Eccentric Adaptor Set Screw Eccentric Eccentric 12.000 UC201 UEL201 1017-12G 1/2 12.700 UC201-008 UEL201-008 1017-1/2G UCS201-008-SNRDG 9/16 14.288 UC202-009 UEL202-009 15.000 UC202 UEL202 1017-15G 5/8 15.875 UC202-010 UEL202-010 1017-5/8G UCS202-010-SNRDG 17.000 UC203 UEL203 1017-17G UCS203-SNRDG 11/16 17.462 UC203-011 UEL203-011 UCS203-011-SNRDG 3/4 19.050 UC204-012 UEL204-012 UK205 HE2305 1020-3/4G T1020-3/4G 1020-3/4DECG UCS204-012-SNRDG 20.000 UC204 UEL204 UK205 H2305 1020-20G T1020-20G 1020-20DECG UCS204-SNRDG 13/16 20.638 UC205-013 UEL205-013 UCS205-013-SNRDG 7/8 22.225 UC205-014 UEL205-014 UK206 HS2306 1025-7/8G T1025-7/8G 1025-7/8DECG T1025-7/8DECG UCS205-014-SNRDG 15/16 23.812 UC205-015 UEL205-015 UK206 HA2306 1025-15/16G T1025-15/16G 1025-15/16DECG T1025-15/16DECG UCS205-015-SNRDG 25.000 UC205 UEL205 UK206 H2306 1025-25G T1025-25G 1025-25DECG T1025-25DECG UCS205-SNRDG 1 25.400 UC205-100 UEL205-100 UK206 HE2306 1025-1G T1025-1G 1025-1DECG T1025-1DECG UCS205-100-SNRDG 1-1/16 26.988 UC206-101 UEL206-101 UCS206-101-SNRDG 1-1/8 28.575 UC206-102 UEL206-102 UK207 HS2307 1030-1-1/8G T1030-1-1/8G 1030-1-1/8DECG T1030-1-1/8DECG UCS206-102-SNRDG 30.000 UC206 UEL206 UK207 H2307 1030-30G T1030-30G 1030-30DECG T1030-30DECG UCS206-SNRDG 1-3/16 30.162 UC206-103 UEL206-103 UK207 HA2307 1030-1-3/16G T1030-1-3/16G 1030-1-3/16DECG T1030-1-3/16DECG UCS206-103-SNRDG 1-1/4 31.750 UC206-104 UEL206-104 1030-1-1/4G T1030-1-1/4G 1030-1-1/4DECG T1030-1-1/4DECG UCS206-104-SNRDG 1-1/4 31.750 UC207-104 UEL207-104 UK208 HE2308 1035-1-1/4G T1035-1-1/4G 1035-1-1/4DECG T1035-1-1/4DECG UCS207-104-SNRDG 1-5/16 33.338 UC207-105 UEL207-105 1035-1-5/16G UCS207-105-SNRDG 1-3/8 34.925 UC207-106 UEL207-106 UK208 HS2308 1035-1-3/8G T1035-1-3/8G 1035-1-3/8DECG T1035-1-3/8DECG UCS207-106-SNRDG 35.000 UC207 UEL207 UK208 H2308 1035-35G T1035-35G 1035-35DECG T1035-35DECG UCS207-SNRDG 1-7/16 36.512 UC207-107 UEL207-107 1035-1-7/16G T1035-1-7/16G 1035-1-7/16DECG T1035-1-7/16DECG UCS207-107-SNRDG 1-7/16 36.512 UC208-107 UEL208-107 UK209 HA2309 1040-1-7/16G T1040-1-7/16G UCS208-107-SNRDG 1-1/2 38.100 UC208-108 UEL208-108 UK209 HE2309 1040-1-1/2G T1040-1-1/2G 1040-1-1/2DECG T1040-1-1/2DECG UCS208-108-SNRDG 1-9/16 39.688 UC208-109 UEL208-109 UCS208-109-SNRDG 40.000 UC208 UEL208 UK209 H2309 1040-40G T1040-40G 1040-40DECG T1040-40DECG UCS208-SNRDG 1-5/8 41.275 UC209-110 UEL209-110 UK209 HS2309 1045-1-5/8G T1045-1-5/8G 1045-1-5/8DECG T1045-1-5/8DECG UCS209-110-SNRDG 1-11/16 42.862 UC209-111 UEL209-111 UK210 HA2310 1045-1-11/16G T1045-1-11/16G 1045-1-11/16DECG T1045-1-11/16DECG UCS209-111-SNRDG 1-3/4 44.450 UC209-112 UEL209-112 UK210 HE2310 1045-1-3/4G T1045-1-3/4G 1045-1-3/4DECG T1045-1-3/4DECG UCS209-112-SNRDG 45.000 UC209 UEL209 UK210 H2310 1045-45G T1045-45G 1045-45DECG T1045-45DECG UCS209-SNRDG 1-13/16 46.038 UC210-113 UEL210-113 UCS210-113-SNRDG 1-7/8 47.625 UC210-114 UEL210-114 UK211 HS2311 1050-1-7/8G T1050-1-7/8G 1050-1-7/8DECG T1050-1-7/8DECG UCS210-114-SNRDG 1-15/16 49.212 UC210-115 UEL210-115 UK211 HA2311 1050-1-15/16G T1050-1-15/16G 1050-1-15/16DECG T1050-1-15/16DECG UCS210-115-SNRDG 50.000 UC210 UEL210 UK211 H2311 1050-50G T1050-50G 1050-50DECG T1050-50DECG UCS210-SNRDG 2 50.800 UC210-200 UEL210-200 UK211 HE2311 1050-2G T1050-2G 1055-2DECG T1055-2DECG UCS210-200-SNRDG 2 50.800 UC211-200 UEL211-200 1055-2G T1055-2G 1055-2DECG T1055-2DECG UCS211-200-SNRDG 2-1/16 52.388 UC211-201 UEL211-201 UCS211-201-SNRDG 2-1/8 53.975 UC211-202 UEL211-202 UK212 HS2312 1055-2-1/8G T1055-2-1/8G 1055-2-1/8DECG T1055-2-1/8DECG UCS211-202-SNRDG 55.000 UC211 UEL211 UK212 H2312 1055-55G T1055-55G 1055-55DECG T1055-55DECG UCS211-SNRDG 2-3/16 55.562 UC211-203 UEL211-203 UK213 HA2313 1055-2-3/16G T1055-2-3/16G 1055-2-3/16DECG T1055-2-3/16DECG UCS211-203-SNRDG 2-1/4 57.150 UC212-204 UEL212-204 UK213 HE2313 1060-2-1/4G T1060-2-1/4G 1060-2-1/4DECG T1060-2-1/4DECG 2-5/16 58.738 UC212-205 UEL212-205 60.000 UC212 UEL212 UK213 H2313 1060-60G T1060-60G 1060-60DECG T1060-60DECG UCS212-SNRDG 2-3/8 60.325 UC212-206 UEL212-206 UK213 HS2313 1060-2-3/8G T1060-2-3/8G 1060-2-3/8DECG T1060-2-3/8DECG 2-7/16 61.912 UC213-207 UEL213-207 UK215 HA2315 1060-2-7/16G T1060-2-7/16G 1060-2-7/16DECG T1060-2-7/16DECG 2-1/2 63.500 UC213-208 UEL213-208 UK215 HE2315 1065-2-1/2G T1070-2-1/2G 1065-2-1/2DECG T1070-2-1/2DECG UCS213-208-SNRDG 65.000 UC213 UEL213 UK215 H2315 1065-65G T1070-65G 1070-65DECG T1070-65DECG UCS213-SNRDG 2-5/8 66.675 UC214-210 UEL214-210 1070-2-5/8G T1070-2-5/8G 1070-2-5/8DECG 2-11/16 68.262 UC214-211 UEL214-211 UK216 HA2316 1070-2-11/16G T1070-2-11/16G 1070-2-11/16DECG 2-3/4 69.850 UC214-212 UEL214-212 UK216 HE2316 1075-2-3/4G 1075-2-3/4DECG 70.000 UC214 UEL214 UK216 H2316 1070-70G T1070-70G 1070-70DECG T1070-70DECG UCS214-SNRDG 2-13/16 71.438 UC215-213 UEL215-213 2-7/8 73.025 UC215-214 UEL215-214 1075-2-7/8G 1075-2-7/8DECG 2-15/16 74.612 UC215-215 UEL215-215 UK217 HA2317 1075-2-15/16G T1080-2-15/16G 1075-2-15/16DECG 75.000 UC215 UEL215 UK217 H2317 1075-75G T1080-75G 1075-75DECG UCS215-SNRDG 3 76.200 UC215-300 UEL215-300 UK217 HE2317 1075-3G T1080-3G 3-1/8 79.375 UC216-302 UK218 HS2318 80.000 UC216 UK218 H2318 1080-80G T1080-80G UCS216-SNRDG 3-3/16 80.962 UC216-303 UK218 HA2318 1080-3-3/16G 3-1/4 82.550 UC217-304 1080-3-1/4G 85.000 UC217 1085-85G UCS217-SNRDG 3-7/16 87.312 UC218-307 1085-3-7/16G 3-1/2 88.900 UC218-308 1090-3-1/2G 90.000 UC218 1090-90G UCS218-SNRDG Notes: 300, X Series housings and RHP housings are available. Limiting speeds apply depending on shaft tolerance. If RHP product is to be used in Japanese standard housings, the bearing Part Number is prefixed J. 164
BALL BRG UNITS Standard Pillow Blocks with Set Screws: UCP 200 Shaft Diameter: 12-90 mm 1/2 to 3-1/2 inches Pillow Blocks: Cast Iron UCP 200 Part No. Example: For Bearing UC 205 Order Complete Unit UCP 205 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No. Diameter No. H A E B S1 S2 G W Bi N Size No. Wt. inch mm mm Kg UCP201 12 UC 201 30.2 127 95 38 13 19 15 62 31.0 12.7 M10 P203 0.70 UCP201-008 1/2 12.700 UC201-008 UCP202-009 9/16 14.288 UC202-009 UCP202 15 UC202 30.2 127 95 38 13 19 15 62 31.0 12.7 M10 P203 0.69 UCP202-010 5/8 15.875 UC202-010 UCP203 17 UC203 30.2 127 95 38 13 19 15 62 31.0 12.7 M10 P203 0.68 UCP203-011 11/16 17.462 UC203-011 UCP204-012 3/4 19.050 UC204-012 33.3 127 95 38 13 19 15 65 31.0 12.7 M10 P204 0.68 UCP204 20 UC204 UCP205-013 13/16 20.638 UC205-013 UCP205-014 7/8 22.225 UC205-014 UCP205-015 15/16 23.812 UC205-015 36.5 140 105 38 13 19 16 70 34.0 14.8 M10 P205 0.84 UCP205 25 UC205 UCP205-100 1 25.400 UC205-100 UCP206-101 1-1/16 26.988 UC206-101 UCP206-102 1-1/8 28.575 UC206-102 UCP206 30 UC206 42.9 165 121 48 17 21 18 83 38.1 15.9 M14 P206 1.36 UCP206-103 1-3/16 30.162 UC206-103 UCP206-104 1-1/4 31.750 UC206-104 UCP207-104 1-1/4 31.750 UC207-104 UCP207-105 1-5/16 33.338 UC207-105 UCP207-106 1-3/8 34.925 UC207-106 47.6 167 127 48 17 21 19 94 42.9 17.5 M14 P207 1.74 UCP207 35 UC207 UCP207-107 1-7/16 36.512 UC207-107 UCP208-107 1-7/16 36.512 UC208-107 UCP208-108 1-1/2 38.100 UC208-108 49.2 184 137 54 17 23 19 100 49.2 19.0 M14 P208 2.20 UCP208-109 1-9/16 39.688 UC208-109 UCP208 40 UC208 UCP209-110 1-5/8 41.275 UC209-110 UCP209-111 1-11/16 42.862 UC209-111 54.0 190 146 54 17 23 20 108 49.2 19.0 M14 P209 2.40 UCP209-112 1-3/4 44.450 UC209-112 UCP209 45 UC209 UCP210-113 1-13/16 46.038 UC210-113 UCP210-114 1-7/8 47.625 UC210-114 UCP210-115 1-15/16 49.212 UC210-115 57.2 206 159 60 20 25 22 114 51.6 19.0 M16 P210 2.70 UCP210 50 UC210 UCP210-200 2 50.800 UC210-200 UCP211-200 2 50.800 UC211-200 UCP211-201 2-1/16 52.388 UC211-201 UCP211-202 2-1/8 53.975 UC211-202 63.5 219 171 60 20 25 22 126 55.6 22.2 M16 P211 3.40 UCP211 55 UC211 UCP211-203 2-3/16 55.562 UC211-203 UCP212-204 2-1/4 57.150 UC212-204 UCP212-205 2-5/16 58.738 UC212-205 69.8 241 184 70 20 25 25 138 65.1 25.4 M16 P212 4.90 UCP212 60 UC212 UCP212-206 2-3/8 60.325 UC212-206 UCP213-207 2-7/16 61.912 UC213-207 UCP213-208 2-1/2 63.500 UC213-208 76.2 265 203 70 25 29 27 150 65.1 25.4 M20 P213 5.80 UCP213 65 UC213 UCP214-210 2-5/8 66.675 UC214-210 UCP214-211 2-11/16 68.262 UC214-211 79.4 266 210 72 25 31 27 156 74.6 30.2 M20 P214 6.50 UCP214-212 2-3/4 69.850 UC214-212 UCP214 70 UC214 UCP215-213 2-13/16 71.438 UC215-213 UCP215-214 2-7/8 73.025 UC215-214 UCP215-215 2-15/16 74.612 UC215-215 82.6 275 217 74 25 31 28 163 77.8 33.3 M20 P215 7.20 UCP215 75 UC215 UCP215-300 3 76.200 UC215-300 UCP216-302 3-1/8 79.375 UC216-302 UCP216 80 UC216 88.9 292 232 78 25 31 30 175 82.6 33.3 M20 P216 8.70 UCP216-303 3-3/16 80.962 UC216-303 UCP217-304 3-1/4 82.550 UC217-304 95.2 310 247 83 25 31 32 187 85.7 34.1 M20 P217 11.20 UCP217 85 UC217 UCP218-307 3-7/16 87.312 UC218-307 UCP218-308 3-1/2 88.900 UC218-308 101.6 327 262 88 27 33 34 200 96.0 39.7 M22 P218 13.40 UCP218 90 UC218 Note: To obtain the shaft diameter in fractions, the second figure in the above unit numbers is the diameter in sixteenths of an inch. Example: For Unit No UCP216-50, the shaft dia is 3-1/8 inches. 165
BALL BRG UNITS Pillow Blocks: Cast Iron UCP X00, UCP300 Standard Pillow Blocks with Set Screws: UCPX 00 Shaft Diameter: 23.812 101.6 mm Part No. Example: For Bearing UC X15 Order Complete Unit UCP X15 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No. Diameter No. H A E B S1 S2 G W Bi N Size No. Wt. mm inch mm Kg UCPX05-015 23.812 15/16 UC206-015 UCPX05 25 UCX05 44.4 159 119 51 17 21 16 83 38.1 15.9 M14 PX05 1.31 UCPX05-100 25.400 1 UC206-100 UCPX06 30 UCX06 UCPX06-103 30.162 1-3/16 UC207-103 47.6 175 127 57 17 21 18 93 42.9 17.5 M14 PX06 1.86 UCPX06-104 31.750 1-1/4 UC207-104 UCPX07 35 UCX07 54.0 203 144 57 17 26 20 104 49.2 19.0 M14 PX07 2.40 UCPX07-107 36.512 1-7/16 UC208-107 UCPX08-108 38.100 1-1/2 UC209-108 58.7 222 156 67 20 28 21 112 49.2 19.0 M16 PX08 3.10 UCPX08 40 UCX08 UCPX09-111 42.862 1-11/16 UC210-111 UCPX09-112 44.450 1-3/4 UC210-112 58.7 222 156 67 20 29 22 115 51.6 19.0 M16 PX09 3.20 UCPX09 45 UCX09 UCPX10-115 49.212 1-15/16 UC211-115 UCPX10 50 UCX10 63.5 241 171 73 20 30 25 126 55.6 22.2 M16 PX10 4.20 UCPX10-200 50.800 2 UC211-200 UCPX11 55 UCX11 UCPX11-203 55.562 2-3/16 UC212-203 69.8 260 184 79 25 30 28 139 65.1 25.4 M20 PX11 5.60 UCPX11-204 57.150 2-1/4 UC212-204 UCPX12 60 UCX12 76.2 286 203 83 25 35 30 151 65.1 25.4 M20 PX12 6.90 UCPX13-207 61.912 2-7/16 UC214-207 UCPX13-208 63.500 2-1/2 UC214-208 76.2 286 203 83 25 35 31 154 74.6 30.2 M20 PX13 7.50 UCPX13 65 UCX13 UCPX14-211 68.262 2-11/16 UC215-211 UCPX14-212 69.850 2-3/4 UC215-212 88.9 330 229 89 27 39 32 170 77.8 33.3 M22 PX14 9.10 UCPX14 70 UCX14 UCPX15-215 74.612 2-15/16 UC216-215 UCPX15 75 UCX15 88.9 330 229 89 27 39 35 175 82.6 33.3 M22 PX15 10.30 UCPX15-300 76.200 3 UC216-300 UCPX16 80 UCX16 UCPX16-303 80.962 3-3/16 UC217-303 101.6 381 283 102 27 54 38 196 85.7 34.1 M22 PX16 14.00 UCPX16-304 82.550 3-1/4 UC217-304 UCPX17 85 UCX17 UCPX17-307 87.312 3-7/16 UC218-307 101.6 381 283 102 27 54 40 202 96.0 39.7 M22 PX17 15.40 UCPX17-308 88.900 3-1/2 UC218-308 UCPX18 90 UCX18 101.6 381 283 111 27 54 42 208 104.0 42.9 M22 PX18 17.80 UCPX20 100 UCX20 UCPX20-315 100.012 3-15/16 UC221-315 127.0 432 337 121 33 58 48 246 117.5 49.2 M27 PX20 26.00 UCPX20-400 101.600 4 UC221-400 Note: To obtain the shaft diameter in fractions, the second figure in the above unit numbers is the diameter in sixteenths of an inch. Example: For Unit No UCPX16-51, the shaft dia is 3-3/16 inches. Standard Pillow Blocks: UCP 300 with Set Screws Shaft Diameter: 20.638140 mm Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No. Diameter No. H A E B S1 S2 G W Bi N Size No. Wt. mm inch mm Kg UCP305-013 20.638 13/16 UC305-013 UCP305-014 22.225 7/8 UC305-014 UCP305-015 23.812 15/16 UC305-015 45 175 132 45 17 20 16 83 38 15 M14 P305 1.33 UCP305 25 UC305 UCP305-100 25.400 1 UC305-100 166
BALL BRG UNITS Pillow Blocks: Cast Iron UCP 300 Part No. Example: For Bearing UC 305 Order Complete Unit UCP 305 Complete Unit with Cast Cover: CUCP 305 + C (Open) CUCP 305 + CE (Closed) Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No. Diameter No. H A E B S1 S2 G W Bi N Size No. Wt. mm inch mm Kg UCP306-101 26.988 1-1/16 UC306-101 UCP306-102 28.575 1-1/8 UC306-102 UCP306 30 UC306 50 180 140 50 17 20 19 94 43 17 M14 P306 1.83 UCP306-103 30.162 1-3/16 UC306-103 UCP306-104 31.750 1-1/4 UC306-104 UCP307-104 31.750 1-1/4 UC307-104 UCP307-105 33.338 1-5/16 UC307-105 UCP307-106 34.925 1-3/8 UC307-106 56 210 160 56 17 25 21 105 48 19 M14 P307 2.50 UCP307 35 UC307 UCP307-107 36.512 1-7/16 UC307-107 UCP308-107 36.512 1-7/16 UC308-107 UCP308-108 38.100 1-1/2 UC308-108 60 220 170 60 17 27 23 116 52 19 M14 P308 3.20 UCP308-109 39.688 1-9/16 UC308-109 UCP308 40 UC308 UCP309-110 41.275 1-5/8 UC309-110 UCP309-111 42.862 1-11/16 UC309-111 67 245 190 67 20 30 25 128 57 22 M16 P309 4.30 UCP309-112 44.450 1-3/4 UC309-112 UCP309 45 UC309 UCP310-113 46.038 1-13/16 UC310-113 UCP310-114 47.625 1-7/8 UC310-114 UCP310-115 49.212 1-15/16 UC310-115 75 275 212 75 20 35 28 143 61 22 M16 P310 5.80 UCP310 50 UC310 UCP310-200 50.800 2 UC310-200 UCP311-200 50.800 2 UC311-200 UCP311-201 52.388 2-1/16 UC311-201 UCP311-202 53.975 2-1/8 UC311-202 80 310 236 80 20 38 31 154 66 25 M16 P311 7.40 UCP311 55 UC311 UCP311-203 55.562 2-3/16 UC311-203 UCP312-204 57.150 2-1/4 UC312-204 UCP312-205 58.738 2-5/16 UC312-205 85 330 250 85 25 38 33 165 71 26 M20 P312 9.10 UCP312 60 UC312 UCP312-206 60.325 2-3/8 UC312-206 UCP313-207 61.912 2-7/16 UC313-207 UCP313-208 63.500 2-1/2 UC313-208 90 340 260 90 25 38 36 174 75 30 M20 P313 10.20 UCP313 65 UC313 UCP314-210 66.675 2-5/8 UC314-210 UCP314-211 68.262 2-11/16 UC314-211 95 360 280 90 27 40 40 186 78 33 M22 P314 12.50 UCP314-212 69.850 2-3/4 UC314-212 UCP314 70 UC314 UCP315-213 71.438 2-13/16 UC315-213 UCP315-214 73.025 2-7/8 UC315-214 UCP315-215 74.612 2-15/16 UC315-215 100 380 290 100 27 40 40 197 82 32 M22 P315 14.60 UCP315 75 UC315 UCP315-300 76.200 3 UC315-300 UCP316-302 79.375 3-1/8 UC316-302 UCP316 80 UC316 106 400 300 110 27 40 45 209 86 34 M22 P316 18.10 UCP316-303 80.962 3-3/16 UC316-303 UCP317-304 82.550 3-1/4 UC317-304 112 420 320 110 33 45 45 221 96 40 M27 P317 21.00 UCP317 85 UC317 UCP318-307 87.312 3-7/16 UC318-307 UCP318-308 88.900 3-1/2 UC318-308 118 430 330 110 33 45 50 233 96 40 M27 P318 23.00 UCP318 90 UC318 UCP319 95 UC319 125 470 360 120 36 50 50 250 103 41 M30 P319 29.00 UCP319-312 95.250 3-3/4 UC319-312 UCP320 100 UC320 UCP320-315 100.012 3-15/16 UC320-315 140 490 380 120 36 50 55 275 108 42 M30 P320 36.00 UCP320-400 101.600 4 UC320-400 UCP321 105 UC321 140 490 380 120 36 50 55 278 112 44 M30 P321 36.00 UCP322 110 UC322 150 520 400 140 40 55 60 295 117 46 M33 P322 45.00 UCP324 120 UC324 160 570 450 140 40 55 70 321 126 51 M33 P324 61.00 UCP326 130 UC326 180 600 480 140 40 55 80 354 135 54 M33 P326 75.00 UCP328 140 UC328 200 620 500 140 40 55 80 388 145 59 M33 P328 91.00 Note: To obtain the shaft diameter in fractions, the second figure in the above unit numbers is the diameter in sixteenths of an inch. Example: For Unit No UCP306-18, the shaft dia is 1-1/8 inches. 167
BALL BRG UNITS Pillow Blocks: Cast Iron UKP 200 Standard Pillow Blocks UKP 200 + H with Adapter Shaft Diameter: 19.050-80.962 mm 3/4 to 3-3/16 inches Part No. Example: For Bearing UK 206 Order Complete Unit UKP 206 With Adapter Sleeves for 25mm shaft UKP 206 + H2306 Unit Shaft Diameter Bearing Dimensions in mm Bolt Housing Approx No. mm inch No. H A E B S1 S2 G W L Size No. Wt. mm Kg UKP205+HE2305 19.050 3/4 UK205 36.5 140 105 38 13 19 16 70 35 M10 P205 0.88 UKP205+H 2305 20 UKP206+HS2306 22.225 7/8 UKP206+HA2306 23.812 15/16 UK206 42.9 165 121 48 17 21 18 83 38 M14 P206 1.46 UKP206+H 2306 25 UKP206+HE2306 25.400 1 UKP207+HS2307 28.575 1-1/8 UKP207+H 2307 30 UK207 47.6 167 127 48 17 21 19 94 43 M14 P207 1.78 UKP207+HA2307 30.162 1-3/16 UKP208+HE2308 31.750 1-1/4 UKP208+HS2308 34.925 1-3/8 UK208 49.2 184 137 54 17 23 19 100 46 M14 P208 2.20 UKP208+H 2308 35 UKP209+HA2309 36.512 1-7/16 UKP209+HE2309 38.100 1-1/2 UK209 54.0 190 146 54 17 23 20 108 50 M14 P209 2.40 UKP209+H 2309 40 UKP210+HS2310 41.275 1-5/8 UKP210+HA2310 42.862 1-11/16 UK210 57.2 206 159 60 20 25 22 114 55 M16 P210 3.00 UKP210+HE2310 44.450 1-3/4 UKP210+H 2310 45 UKP211+HS2311 47.625 1-7/8 UKP211+HA2311 49.212 1-15/16 UK211 63.5 219 171 60 20 25 22 126 59 M16 P211 3.50 UKP211+H 2311 50 UKP211+HE2311 50.800 2 UKP212+HS2312 53.975 2-1/8 UK212 69.8 241 184 70 20 25 25 138 62 M16 P212 4.80 UKP212+H 2312 55 UKP213+HA2313 55.562 2-3/16 UKP213+HE2313 57.150 2-1/4 UK213 76.2 265 203 70 25 29 27 150 65 M20 P213 5.80 UKP213+H 2313 60 UKP213+HS2313 60.325 2-3/8 UKP215+HA2315 61.912 2-7/16 UKP215+HE2315 63.500 2-1/2 UK215 82.6 275 217 74 25 31 28 163 73 M20 P215 7.60 UKP215+H 2315 65 UKP216+HA2316 68.262 2-11/16 UKP216+HE2316 69.850 2-3/4 UK216 88.9 292 232 78 25 31 30 175 78 M20 P216 9.20 UKP216+H 2316 70 UKP217+HA2317 74.612 2-15/16 UKP217+H 2317 75 UK217 95.2 310 247 83 25 31 32 187 82 M20 P217 11.30 UKP217+HE2317 76.200 3 UKP218+HS2318 79.375 3-1/8 UKP218+H 2318 80 UK218 101.6 327 262 88 27 33 34 200 86 M22 P218 13.90 UKP218+HA2318 80.962 3-3/16 Note: Pressed steel covers are available. Please contact any branch near you for details. 168
BALL BRG UNITS Pillow Blocks: Cast Iron UKP X00 Standard Pillow Blocks UKP X00 + H with Adapter Shaft Diameter: 19.050 90 mm 3/4 to 3-1/2 inches Part No. Example: For Bearing UK X20 Order Complete Unit UKP X20 With Adapter Sleeve for 90mm shaft UKP X20 + H2320 Unit Shaft Diameter Bearing Dimensions in mm Bolt Housing Approx No. mm inch No. H A E B S1 S2 G W L Size No. Wt. mm Kg UKPX05+HE2305 19.050 3/4 UKX05 44.4 159 119 51 17 21 16 83 35 M14 PX05 1.32 UKPX05+H 2305 20 UKPX06+HS2306 22.225 7/8 UKPX06+HA2306 23.812 15/16 UKX06 47.6 175 127 57 17 21 18 93 38 M14 PX06 1.86 UKPX06+H 2306 25 UKPX06+HE2306 25.400 1 UKPX07+HS2307 28.575 1-1/8 UKPX07+H 2307 30 UKX07 54.0 203 144 57 17 26 20 104 43 M14 PX07 2.40 UKPX07+HA2307 30.162 1-3/16 UKPX08+HE2308 31.750 1-1/4 UKPX08+HS2308 34.925 1-3/8 UKX08 58.7 222 156 67 20 28 21 112 46 M16 PX08 3.10 UKPX08+H 2308 35 UKPX09+HA2309 36.512 1-7/16 UKPX09+HE2309 38.100 1-1/2 UKX09 58.7 222 156 67 20 29 22 115 50 M16 PX09 3.20 UKPX09+H 2309 40 UKPX10+HS2310 41.275 1-5/8 UKPX10+HA2310 42.862 1-11/16 UKX10 63.5 241 171 73 20 30 25 126 55 M16 PX10 4.30 UKPX10+HE2310 44.450 1-3/4 UKPX10+H 2310 45 UKPX11+HS2311 47.625 1-7/8 UKPX11+HA2311 49.212 1-15/16 UKX11 69.8 260 184 79 25 30 28 139 59 M20 PX11 5.50 UKPX11+H 2311 50 UKPX11+HE2311 50.800 2 UKPX12+HS2312 53.975 2-1/8 UKX12 76.2 286 203 83 25 35 30 151 62 M20 PX12 6.80 UKPX12+H 2312 55 UKPX13+HA2313 55.562 2-3/16 UKPX13+HE2313 57.150 2-1/4 UKX13 76.2 286 203 83 25 35 31 154 65 M20 PX13 7.30 UKPX13+H 2313 60 UKPX15+HA2315 61.912 2-7/16 UKPX15+HE2315 63.500 2-1/2 UKX15 88.9 330 229 89 27 39 35 175 73 M22 PX15 10.40 UKPX15+H 2315 65 UKPX16+HA2316 68.262 2-11/16 UKPX16+HE2316 69.850 2-3/4 UKX16 101.6 381 283 102 27 54 38 196 78 M22 PX16 14.00 UKPX16+H 2316 70 UKPX17+HA2317 74.612 2-15/16 UKPX17+H 2317 75 UKX17 101.6 381 283 102 27 54 40 202 82 M22 PX17 15.80 UKPX17+HE2317 76.200 3 UKPX18+H 2318 80 UKX18 101.6 381 283 111 27 54 42 208 86 M22 PX18 17.30 UKPX18+HA2318 80.962 3-3/16 UKPX20+HE2320 88.900 3-1/2 UKX20 127.0 432 337 121 33 58 48 246 97 M27 PX20 25.00 UKPX20+H 2320 90 169
BALL BRG UNITS Standard Pillow Blocks UKP 300 + H with Adapter Shaft Diameter: 19.050-125 mm 3/4 to 4 inches Pillow Blocks: Cast Iron UKP 300 Part No. Example: For Bearing UK 306 Order Complete Unit UKP 306 With Adapter Sleeve for 90mm shaft UKP 306 + H2306 Unit Shaft Diameter Bearing Dimensions in mm Bolt Hsng Appr No. mm inch No. H A E B S1 S2 G W L Size No. Wt. mm Kg UKP305+HE2305 19.050 3/4 UK305 45 175 132 45 17 20 16 83 35 M14 P305 1.34 UKP305+H 2305 20 UKP306+HS2306 22.225 7/8 UKP306+HA2306 23.812 15/16 UK306 50 180 140 50 17 20 19 94 38 M14 P306 1.94 UKP306+H 2306 25 UKP306+HE2306 25.400 1 UKP307+HS2307 28.575 1-1/8 UKP307+H 2307 30 UK307 56 210 160 56 17 25 21 105 43 M14 P307 2.50 UKP307+HA2307 30.162 1-3/16 UKP308+HE2308 31.750 1-1/4 UKP308+HS2308 34.925 1-3/8 UK308 60 220 170 60 17 27 23 116 46 M14 P308 3.20 UKP308+H 2308 35 UKP309+HA2309 36.512 1-7/16 UKP309+HE2309 38.100 1-1/2 UK309 67 245 190 67 20 30 25 128 50 M16 P309 4.30 UKP309+H 2309 40 UKP310+HS2310 41.275 1-5/8 UKP310+HA2310 42.862 1-11/16 UK310 75 275 212 75 20 35 28 143 55 M16 P310 5.90 UKP310+HE2310 44.450 1-3/4 UKP310+H 2310 45 UKP311+HS2311 47.625 1-7/8 UKP311+HA2311 49.212 1-15/16 UK311 80 310 236 80 20 38 31 154 59 M16 P311 7.40 UKP311+H 2311 50 UKP311+HE2311 50.800 2 UKP312+HS2312 53.975 2-1/8 UK312 85 330 250 85 25 38 33 165 62 M20 P312 8.90 UKP312+H 2312 55 UKP313+HA2313 55.562 2-3/16 UKP313+HE2313 57.150 2-1/4 UK313 90 340 260 90 25 38 36 174 65 M20 P313 10.20 UKP313+H 2313 60 UKP313+HS2313 60.325 2-3/8 UKP315+HA2315 61.912 2-7/16 UKP315+HE2315 63.500 2-1/2 UK315 100 380 290 100 27 40 40 197 73 M22 P315 14.80 UKP315+H 2315 65 UKP316+HA2316 68.262 2-11/16 UKP316+HE2316 69.850 2-3/4 UK316 106 400 300 110 27 40 45 209 78 M22 P316 18.30 UKP316+H 2316 70 UKP317+HA2317 74.612 UKP317+H 2317 75 UK317 112 420 320 110 33 45 45 221 82 M27 P317 21.00 UKP317+HE2317 76.200 3 UKP318+HS2318 79.375 3-1/8 UKP318+H 2318 80 UK318 118 430 330 110 33 45 50 233 86 M27 P318 23.00 UKP318+HA2318 80.962 3-3/16 UKP319+HE2319 82.550 3-1/4 UK319 125 470 360 120 36 50 50 250 90 M30 P319 29.00 UKP319+H 2319 85 UKP320+HE2320 88.900 3-1/2 UK320 140 490 380 120 36 50 55 275 97 M30 P320 35.00 UKP320+H 2320 90 UKP322+H 2322 100 UKP322+HE2322 101.600 4 UK322 150 520 400 140 40 55 60 295 105 M33 P322 45.00 UKP324+H 2324 110 UK324 160 570 450 140 40 55 70 321 112 M33 P324 60.00 UKP326+H 2326 115 UK326 180 600 480 140 40 55 80 354 121 M33 P326 75.00 UKP328+H 2328 125 UK328 200 620 500 140 40 55 80 388 131 M33 P328 90.00 170
BALL BRG UNITS Pillow Blocks: Cast Iron UELP 200 Standard Pillow Blocks UELP 200 with Eccentric Locking Collar Shaft Diameter: 19.050-76.200 mm 3/4 to 3 inches Part No. Example: For Bearing UEL 204 Order Complete Unit UELP 204 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No. Diameter No. H A E B S1 S2 G W Bi N Size No. Wt. mm inch mm Kg UELP204-012 19.050 3/4 UEL204-012 33.3 127 95 38 13 19 15 65 43.7 17.1 M10 P204 0.74 UELP204 20 UEL204 UELP205-013 20.638 13/16 UEL205-013 UELP205-014 22.225 7/8 UEL205-014 UELP205-015 23.812 15/16 UEL205-015 36.5 140 105 38 13 19 16 70 44.4 17.5 M10 P205 0.88 UELP205 25 UEL205 UELP205-100 25.400 1 UEL205-100 UELP206-101 26.988 1-1/16 UEL206-101 UELP206-102 28.575 1-1/8 UEL206-102 UELP206 30 UEL206 42.9 165 121 48 17 21 18 83 48.4 18.3 M14 P206 1.42 UELP206-103 30.162 1-3/16 UEL206-103 UELP206-104 31.750 1-1/4 UEL206-104 UELP207-104 31.750 1-1/4 UEL207-104 UELP207-105 33.338 1-5/16 UEL207-105 UELP207-106 34.925 1-3/8 UEL207-106 47.6 167 127 48 17 21 19 94 51.1 18.8 M14 P207 1.86 UELP207 35 UEL207 UELP207-107 36.512 1-7/16 UEL207-107 UELP208-107 36.512 1-7/16 UEL208-107 UELP208-108 38.100 1-1/2 UEL208-108 49.2 184 137 54 17 23 19 100 56.3 21.4 M14 P208 2.30 UELP208-109 39.688 1-9/16 UEL208-109 UELP208 40 UEL208 UELP209-110 41.275 1-5/8 UEL209-110 UELP209-111 42.862 1-11/16 UEL209-111 54.0 190 146 54 17 23 20 108 56.3 21.4 M14 P209 2.50 UELP209-112 44.450 1-3/4 UEL209-112 UELP209 45 UEL209 UELP210-113 46.038 1-13/16 UEL210-113 UELP210-114 47.625 1-7/8 UEL210-114 UELP210-115 49.212 1-15/16 UEL210-115 57.2 206 159 60 20 25 22 114 62.7 24.6 M16 P210 2.90 UELP210 50 UEL210 UELP210-200 50.800 2 UEL210-200 UELP211-200 50.800 2 UEL211-200 UELP211-201 52.388 2-1/16 UEL211-201 UELP211-202 53.975 2-1/8 UEL211-202 63.5 219 171 60 20 25 22 126 71.4 27.8 M16 P211 3.70 UELP211 55 UEL211 UELP211-203 55.562 2-3/16 UEL211-203 UELP212-204 57.150 2-1/4 UEL212-204 UELP212-205 58.738 2-5/16 UEL212-205 69.8 241 184 70 20 25 25 138 77.8 31.0 M16 P212 5.10 UELP212 60 UEL212 UELP212-206 60.325 2-3/8 UEL212-206 UELP213-207 61.912 2-7/16 UEL213-207 UELP213-208 63.500 2-1/2 UEL213-208 76.2 265 203 70 25 29 27 150 85.7 34.1 M20 P213 6.30 UELP213 65 UEL213 UELP214-210 66.675 2-5/8 UEL214-210 UELP214-211 68.262 2-11/16 UEL214-211 79.4 266 210 72 25 31 27 156 85.7 34.1 M20 P214 7.00 UELP214-212 69.850 2-3/4 UEL214-212 UELP214 70 UEL214 UELP215-213 71.438 2-13/16 UEL215-213 UELP215-214 73.025 2-7/8 UEL215-214 UELP215-215 74.612 2-15/16 UEL215-215 82.6 275 217 74 25 31 28 163 92.1 37.3 M20 P215 7.60 UELP215 75 UEL215 UELP215-300 76.200 3 UEL215-300 171
BALL BRG UNITS Pillow Blocks: Normal Duty UCSB2 Part No. Example: For Bearing UC 205 Order Complete Unit UCSB 205 Dust-proof covers S for open type SM for closed type Unit Shaft Diameter Bearing Dimensions in mm Basic No. inch mm No. H A E B C G W Bi M S T Dyn Cap kn UCSB205-014 7/8 22.225 UC205-014 UCSB205-015 15/16 23.812 UC205-015 31.70 92 70 38 25 58 67 34.0 19.7 11.0 60 14.0 UCSB205 25 UC205 UCSB205-100 1 25.400 UC205-100 UCSB206-102 1-1/8 28.575 UC206-102 UCSB206 30 UC206 38.10 108 83 44 30 68 78 38.1 22.2 11.0 65 19.5 UCSB206-103 1-3/16 30.162 UC206-103 UCSB207-104 1-1/4 31.750 UC207-104 UCSB207-105 1-5/16 33.338 UC207-105 UCSB207-106 1-3/8 34.925 UC207-106 44.40 133 102 48 33 76 95 42.8 25.4 14.0 75 25.7 UCSB207 35 UC207 UCSB207-107 1-7/16 36.512 UC207-107 UCSB208-108 1-1/2 38.100 UC208-108 UCSB208 1-9/16 39.688 UC208 47.60 140 108 54 39 81 100 49.0 30.0 14.0 85 29.1 UCSB208 40 UC208 UCSB209-110 1-5/8 41.275 UC209-110 UCSB209-111 1-11/16 42.862 UC209-111 50.80 146 111 54 39 86 105 49.0 30.0 14.0 85 32.5 UCSB209-112 1-3/4 44.450 UC209-112 UCSB209 45 UC209 UCSB210-114 1-7/8 47.625 UC210-114 UCSB210-115 1-15/16 49.212 UC210-115 53.97 152 118 60 41 90 110 52.0 33.0 14.0 91 35.0 UCSB210 50 UC210 UCSB211-200 2 50.800 UC211-200 UCSB211-202 2-1/8 53.975 UC211-202 58.70 172 137 60 41 98 122 56.0 33.0 17.0 98 43.5 UCSB211 55 UC211 UCSB211-203 2-3/16 55.562 UC211-203 UCSB212-204 2-1/4 57.150 UC212-204 UCSB212 60 UC212 69.85 197 162 65 48 111 146 65.0 40.0 17.0 105 52.5 UCSB212-206 2-3/8 60.325 UC212-206 UCSB212-207 2-7/16 61.912 UC212-207 UCSB213-208 2-1/2 63.500 UC213-208 69.85 197 162 65 48 111 146 65.0 40.0 17.0 112 57.5 UCSB213 65 UC213 UCSB214-211 2-11/16 68.262 UC214-211 UCSB214-212 2-3/4 69.850 UC214-212 76.20 206 172 73 60 117 155 75.0 45.0 17.0 62.0 UCSB214 70 UC214 UCSB215 75 UC215 UCSB215-215 2-15/16 74.613 UC215-215 76.20 206 172 73 60 117 155 77.8 45.0 17.0 66.0 UCSB215-300 3 76.200 UC215-300 UCSB216 80 UC216 82.55 238 191 86 64 127 168 83.0 49.0 21.0 72.5 UCSB217-304 3-1/4 82.550 UC217-304 88.90 254 203 89 64 136 181 86.0 52.0 21.0 83.5 UCSB217 85 UC217 UCSB218-308 3-1/2 88.900 UC218-308 98.40 273 222 92 67 152 200 96.0 56.0 25.4 96.0 172
BALL BRG UNITS Pillow Blocks: Normal Duty UKSB2 Part No. Example: For Bearing UK 205 Order Complete Unit UKSB 205 Dust-proof covers S for open type SM for closed type Unit Shaft Diameter Bearing Dimensions in mm Basic Adapter No. inch mm No. H A E B C G W Bi M S T Dyn Cap Sleeve kn UKSB205 3/4 19.050 UK205 31.70 92 70 38 25 58 67 35 19.5 11.0 60 14.0 HE2305 UKSB205 20 H 2305 UKSB206 7/8 22.225 HS2306 UKSB206 25 UK206 38.10 108 83 44 30 68 78 38 22.0 11.0 65 19.5 H 2306 UKSB206 1 25.400 HE2306 UKSB207 1-1/8 28.575 UK207 44.40 133 102 48 33 76 95 43 23.7 14.0 75 25.7 HS2307 UKSB207 30 H 2307 UKSB208 1-1/4 31.750 HE2308 UKSB208 1-3/8 34.925 UK208 47.60 140 108 54 39 81 100 46 25.5 14.0 85 29.1 HS2308 UKSB208 35 H 2308 UKSB209 1-7/16 36.512 HA2309 UKSB209 1-1/2 38.100 UK209 50.80 146 111 54 39 86 105 50 26.5 14.0 85 32.5 HE2309 UKSB209 40 H 2309 UKSB210 1-5/8 41.275 HS2310 UKSB210 1-11/16 42.862 UK210 54.00 152 118 60 41 90 110 55 28.0 14.0 91 35.0 HA2310 UKSB210 1-3/4 44.450 HE2310 UKSB210 45 H 2310 UKSB211 1-7/8 47.625 HS2311 UKSB211 1-15/16 49.212 UK211 58.70 172 137 60 41 98 122 59 29.5 17.0 98 43.5 HA2311 UKSB211 50 H 2311 UKSB211 2 50.800 HE2311 UKSB212 2-1/8 53.975 UK212 69.85 197 162 65 48 111 146 62 32.0 17.0 105 52.5 HS2312 UKSB212 55 H 2312 UKSB213 2-3/16 55.562 HA2313 UKSB213 2-1/4 57.150 UK213 69.85 197 162 65 48 111 146 65 34.0 17.0 112 57.5 HE2313 UKSB213 60 H 2313 UKSB213 2-3/8 60.325 HS2313 UKSB215 2-7/16 61.912 HA2315 UKSB215 2-1/2 63.500 UK215 76.20 206 172 73 60 117 155 73 37.0 17.0 66.0 HE2315 UKSB215 65 H 2315 UKSB216 2-11/16 68.262 HA2316 UKSB216 2-3/4 69.850 UK216 82.55 238 191 86 64 127 168 78 39.5 21.0 72.5 HE2316 UKSB216 70 H 2316 UKSB217 2-15/16 74.613 HA2317 UKSB217 75 UK217 89.10 254 203 89 64 136 181 82 41.8 21.0 83.5 H 2317 UKSB217 3 76.200 HE2317 UKSB218 80 UK218 98.40 273 222 92 67 152 200 86 42.8 25.4 96.0 H 2318 173
BALL BRG UNITS Pillow Blocks: Normal Duty UCSBX Part No. Example: For Bearing UCX 05 Order Complete Unit UCSB X05 Unit Shaft Diameter Bearing Dimensions in mm Basic No. inch mm No. H A E B C G W Bi M S Dyn Cap kn UCSBX05-014 7/8 22.225 UCX05-014 UCSBX05-015 15/16 23.812 UCX05-015 38.10 108 83 44 30 68 78 38.1 22.2 11.0 19.5 UCSBX05 25 UCX05 UCSBX05-100 1 25.400 UCX05-100 UCSBX06-102 1-1/8 28.575 UCX06-102 UCSBX06 30 UCX06 44.40 133 102 48 33 76 95 42.9 25.4 14.0 25.7 UCSBX06-103 1-3/16 30.162 UCX06-103 UCSBX06-104 1-1/4 31.750 UCX06-104 UCSBX07-106 1-3/8 34.925 UCX07-106 UCSBX07 35 UCX07 47.60 140 108 54 39 81 100 49.0 30.0 14.0 29.1 UCSBX07-107 1-7/16 36.512 UCX07-107 UCSBX08-108 1-1/2 38.100 UCX08-108 50.80 146 111 54 39 86 105 49.0 30.0 14.0 32.5 UCSBX08 40 UCX08 UCSBX09-110 1-5/8 41.275 UCX09-110 UCSBX09-111 1-11/16 42.862 UCX09-111 53.97 152 118 60 41 90 110 52.0 33.0 14.0 35.0 UCSBX09-112 1-3/4 44.450 UCX09-112 UCSBX09 45 UCX09 UCSBX10-114 1-7/8 47.625 UCX10-114 UCSBX10-115 1-15/16 49.212 UCX10-115 58.70 172 137 60 41 98 122 55.0 33.0 17.0 43.5 UCSBX10 50 UCX10 UCSBX10-200 2 50.800 UCX10-200 UCSBX11-202 2-1/8 53.975 UCX11-202 UCSBX11 55 UCX11 69.85 197 162 65 48 111 146 65.0 40.0 17.0 52.5 UCSBX11-203 2-3/16 55.562 UCX11-203 UCSBX11-204 2-1/4 57.150 UCX11-204 UCSBX12 60 UCX12 UCSBX12-206 2-3/8 60.325 UCX12-206 69.85 197 162 65 48 111 146 65.0 40.0 17.0 57.5 UCSBX12-207 2-7/16 61.912 UCX12-207 UCSBX13-208 2-1/2 63.500 UCX13-208 76.20 206 172 73 60 117 155 75.0 45.0 17.0 62.0 UCSBX13 65 UCX13 UCSBX14-210 2-5/8 66.675 UCX14-210 UCSBX14-211 2-11/16 68.262 UCX14-211 76.20 208 172 73 60 117 155 78.0 45.0 17.0 66.0 UCSBX14-212 2-3/4 69.850 UCX14-212 UCSBX14 70 UCX14 UCSBX15 75 UCX15 UCSBX15-215 2-15/16 74.613 UCX15-215 82.55 238 191 86 64 127 165 83.0 49.0 21.0 72.5 UCSBX15-300 3 76.200 UCX15-300 UCSBX16 80 UCX16 88.90 254 203 89 64 136 181 86.0 52.0 21.0 83.5 UCSBX17-304 3-1/4 82.550 UCX17-304 98.40 273 222 92 67 152 200 96.0 56.0 25.4 96.0 UCSBX17 85 UCX17 UCSBX18-308 3-1/2 88.900 UCX18-308 98.40 273 222 92 67 152 200 104.0 61.0 25.4 109.0 UCSBX18 90 UCX18 UCSBX20 100 UCX20 108.00 298 241 108 76 178 221 117.0 68.0 25.4 133.0 UCSBX20-400 4 101.60 UCX20-400 174
BALL BRG UNITS Pillow Blocks: Normal Duty UKSBX Part No. Example: For Bearing Order Complete Unit UK X05 UKSB X05 + H2305 (to suit 20mm shaft) Unit Shaft Diameter Bearing Dimensions in mm Basic Adapter No. inch mm No. H A E B C G W Bi M S Dyn Cap Sleeve kn UKSBX05 3/4 19.050 UKX05 38.1 108 83 44 30 68 78 35 19.5 11 19.5 HE2305 UKSBX05 20 H 2305 UKSBX06 7/8 22.225 HS2306 UKSBX06 25 UKX06 44.4 133 102 48 33 76 95 38 22 14 25.7 H 2306 UKSBX06 1 25.400 HE2306 UKSBX07 1-1/8 28.575 UKX07 47.6 140 108 54 39 81 100 43 23.7 14 29.1 HS2307 UKSBX07 30 H 2307 UKSBX08 1-1/4 31.750 HE2308 UKSBX08 1-3/8 34.925 UKX08 50.8 146 111 54 39 86 105 46 25.5 14 32.5 HS2308 UKSBX08 35 H 2308 UKSBX09 1-1/2 38.100 UKX09 53.97 152 118 60 41 90 110 50 26.5 14 35.0 HE2309 UKSBX09 40 H 2309 UKSBX10 1-5/8 41.275 HS2310 UKSBX10 1-11/16 42.862 UKX10 58.7 172 137 60 41 98 122 55 28.0 17 43.5 HA2310 UKSBX10 45 H 2310 UKSBX10 1-3/4 44.450 HE2310 UKSBX11 1-7/8 47.625 HS2311 UKSBX11 1-15/16 49.213 UKX11 69.85 197 162 65 48 111 146 59 29.5 17 52.5 HA2311 UKSBX11 50 H 2311 UKSBX11 2 50.800 HE2311 UKSBX12 2-1/8 53.975 UKX12 69.85 197 162 65 48 111 146 62 32 17 57.5 HS2312 UKSBX12 55 H 2312 UKSBX13 2-3/16 55.562 HA2313 UKSBX13 2-1/4 57.150 UKX13 76.2 206 172 73 60 117 155 65 34 17 62.0 HE2313 UKSBX13 60 H 2313 UKSBX13 2-3/8 60.325 HS2313 UKSBX15 2-7/16 61.912 HA2315 UKSBX15 2-1/2 63.500 UKX15 82.55 238 191 86 64 127 168 73 37 21 72.5 HE2315 UKSBX15 65 H 2315 UKSBX16 2-11/16 68.262 HA2316 UKSBX16 2-3/4 69.850 UKX16 88.90 254 206 89 64 136 181 78 39.5 21 83.5 HE2316 UKSBX16 70 H 2316 UKSBX17 2-15/16 74.613 H 2317 UKSBX17 75 UKX17 98.4 273 222 92 67 152 200 82 41.8 25.4 96.0 HA2317 UKSBX17 3 76.200 HE2317 UKSBX18 80 UKX18 98.4 273 222 92 67 152 200 86 42.8 25.4 109. HE2318 UKSBX20 3-1/2 88.900 UKX20 108 298 241 108 76 178 220 97 47.0 25.4 133. HE2320 UKSBX20 90 H 2320 175
BALL BRG UNITS Pillow Blocks: Short Base UCUP 200 Compact Tapped - Base Pillow Blocks UCUP 200 with Set Screws Shaft Diameter: 12 50.800 mm 1/2 to 2 inches Part No. Example: For Bearing UC 205 Order Complete Unit UCUP 205 Unit Shaft Bearing Dimensions in mm Hsng Appr No. Diameter No. H A E B T G W Bi N No. Wt. mml inch mm Kg UCUP201 12 UC201 30.2 76 52 40 M10x1.5 11 62 31.0 12.7 UP204 0.67 UCUP201-008 12.700 1/2 UC201-008 UCUP202-009 14.288 9/16 UC202-009 UCUP202 15 UC202 30.2 76 52 40 M10x1.5 11 62 31.0 12.7 UP204 0.65 UCUP202-010 15.875 5/8 UC202-010 UCUP203 17 UC203 30.2 76 52 40 M10x1.5 11 62 31.0 12.7 UP204 0.64 UCUP203-011 17.462 11/16 UC203-011 UCUP204-012 19.050 3/4 UC204-012 30.2 76 52 40 M10x1.5 11 62 31.0 12.7 UP204 0.62 UCUP204 20 UC204 UCUP205-013 20.638 13/16 UC205-013 UCUP205-014 22.225 7/8 UC205-014 UCUP205-015 23.812 15/16 UC205-015 36.5 84 56 45 M10x1.5 12 72 34.0 14.3 UP205 0.93 UCUP205 25 UC205 UCUP205-100 25.400 1 UC205-100 UCUP206-101 26.988 1-1/16 UC206-101 UCUP206-102 28.575 1-1/8 UC206-102 UCUP206 30 UC206 42.9 94 66 50 M14x2.0 12 84 38.1 15.9 UP206 1.26 UCUP206-103 30.162 1-3/16 UC206-103 UCUP206-104 31.750 1-1/4 UC206-104 UCUP207-104 31.750 1-1/4 UC207-104 UCUP207-105 33.338 1-5/16 UC207-105 UCUP207-106 34.925 1-3/8 UC207-106 47.6 110 80 55 M14x2.0 13 95 42.9 17.5 UP207 1.84 UCUP207 35 UC207 UCUP207-107 36.512 1-7/16 UC207-107 UCUP208-107 36.512 1-7/16 UC208-107 UCUP208-108 38.100 1-1/2 UC208-108 49.2 116 84 58 M14x2.0 13 100 49.2 19.0 UP208 2.20 UCUP208-109 39.688 1-9/16 UC208-109 UCUP208 40 UC208 UCUP209-110 41.275 1-5/8 UC209-110 UCUP209-111 42.862 1-11/16 UC209-111 54.2 120 90 60 M14x2.0 13 108 49.2 19.0 UP209 2.60 UCUP209-112 44.450 1-3/4 UC209-112 UCUP209 45 UC209 UCUP210-113 46.038 1-13/16 UC210-113 UCUP210-114 47.625 1-7/8 UC210-114 UCUP210-115 49.212 1-15/16 UC210-115 57.2 130 94 64 M16x2.0 14 116 51.6 19.0 UP210 2.90 UCUP210 50 UC210 UCUP210-200 50.800 2 UC210-200 176
BALL BRG UNITS Pillow Blocks: Pressed Steel PB, RPB PB Part No. Example: For Bearing AEL205-014 Order Stamping 52PB The PB type pillow block is designed for light-duty applications to provide the advantages of ball bearings at low cost. The unit consists of a two-piece separable steel housing with spherical bearing seat. This allows the spherically-ground bearing initial selfalignment in all directions. The ball bearing is an AEL 200 extended inner ring type with self-locking collar or AS 200 extended inner ring with grub screw locking. Stamp Shaft Bearing Dimensions in mm Size Diameter Numbers A B E F G H J K N O S T LR LS inch mm AEL AS kgf RPM 40PB 12 AEL201 AS201 40PB 1/2 12.700 AEL201-008 AS201-008 22.2 43.7 68.3 85.7 25.4 2.5 9.5 10.3 30.2 18.2 22.1 12.7 136.2 8300 40PB 15 AEL202 AS202 40PB 5/8 15.875 AEL202-010 AS202-010 47PB 20 AEL204 AS204 47PB 3/4 19.050 AEL204-012 AS204-012 25.4 50.4 76.2 98.4 31.8 2.5 9.5 10.3 33.3 21.8 23.5 15.9 158.9 6800 52PB 25 AEL205 AS205 52PB 7/8 22.225 AEL205-014 AS205-014 28.6 56.0 85.7 108.0 31.8 2.8 11.1 11.9 38.1 21.8 23.5 15.9 181.6 6000 52PB 1 25.400 AEL205-100 AS205-100 62PB 30 AEL206 AS206 62PB 1-1/8 28.575 AEL206-102 AS206-102 33.3 65.9 95.3 117.5 38.1 3.6 11.1 11.9 44.5 25.4 26.7 19.1 272.4 4800 62PB 1-1/4 31.750 AEL206-104 AS206-104 RPB Part No. Example: For Bearing AEL205-100 Order Stamping 62RPB Order Insert T20661-3 The RPB type pillow block has the same construction as the PB type, but has a thick, electric-conductive rubber interliner. Bearings in the RPB unit are designated as AEL200 extended inner ring type with self-locking collar. Stamp Shaft Bearing Dimensions in mm Rubber Size Diameter Number A B E F G H J K N O S T LR LS Insul inch mm AEL AS kgf RPM 47RPB 12 AEL201 AS201 47RPB 1/2 12.700 AEL201-008 AS201-008 25.4 50.4 76.2 98.4 31.8 2.5 9.5 10.3 30.2 18.2 22.1 15.9 90.8 6800 T20661-1 47RPB 15 AEL202 AS202 47RPB 5/8 15.875 AEL202-010 AS202-010 52RPB 20 AEL204 AS204 52RPB 3/4 19.050 AEL204-012 AS204-012 28.6 59.9 85.7 108.0 31.8 2.8 11.1 11.9 33.3 21.8 23.5 15.9 113.5 6000 T20661-2 62RPB 25 AEL205 AS205 62RPB 1 25.400 AEL205-100 AS205-100 33.3 65.9 95.3 117.5 38.1 3.6 11.1 11.9 38.1 25.4 23.5 19.1 136.2 4800 T20661-3 72RPB 30 AEL206 AS206 72RPB 1-1/4 31.750 AEL206-104 AS206-104 39.7 77.8 106.3 129.4 42.1 4.6 11.1 11.9 44.5 28.6 27.0 22.2 181.8 4000 T20661-4 * Thrust rating is 30% of radial rating. Recommended shaft tolerance - Up to 50mm(2") dia. inclusive Nominal to -.0127mm(.0005") Over 50mm(2") dia. Nominal to -.0254mm(.0010"). These tolerances correspond to those of precision grounding. 177
BALL BRG UNITS Pillow Blocks: Pressed Steel PBS Part No. Example: For Bearing AEL204-014 Order Stamping 47PBS Note: AEL = Eccentric Locking Collar AS = Set Screw Locking Stamp Shaft Bearing Flange Dimensions in mm Radial* Brg Size Diameter Number No. A B 1 B 2 C D E F G H J K L M N P R Load Limit inch mm AEL AS Rating Speed kg/lbf RPM 40PBS 12 AEL201 AS201 40MST 30.2 92.1 15.9 123.8 59.5 63.5 28.6 22.2 14.3 25.4 2.64 1.91 32.5 7.1 10.3 10.3 272.4 8300 40PBS 1/2 AEL201-008 AS201-008 40PBS 15 AEL202 AS202 40PBS 5/8 AEL202-010 AS202-010 47PBS 20 AEL204 AS204 47MST 33.3 96.8 15.9 127.0 68.3 71.4 33.3 23.4 15.9 25.4 3.00 2.1 33.3 8.7 10.3 10.3 317.8 6800 47PBS 3/4 AEL204-012 AS204-012 52PBS 25 AEL205 AS205 52PBS 7/8 AEL205-014 AS205-014 52PBS 15/16 AEL205-015 AS205-015 52MST 36.5 95.3 20.6 133.4 72.2 76.2 38.1 23.4 17.5 25.4 3.4 2.1 34.1 8.7 11.1 11.1 363.2 6000 52PBS 1 AEL205-100 AS205-100 62PBS 30 AEL206 AS206 62PBS 1-1/16 AEL206-101 AS206-101 62PBS 1-1/8 AEL206-102 AS206-102 62MST 42.9 119.1 22.2 158.8 84.9 90.5 44.5 26.6 17.5 30.2 3.4 2.64 37.3 10.3 14.3 14.3 363.2 4800 62PBS 1-3/16 AEL206-103 AS206-103 62PBS 1-1/4 AEL206-104 AS206-104 72PBS 35 AEL207 AS207 72PBS 1-1/4 AEL207-104 AS207-104 72PBS 1-3/8 AEL207-106 AS207-106 72MST 47.6 127 22.2 165.1 94.5 100.0 55.6 29.4 22.2 34.9 3.78 2.64 46.0 10.3 14.3 14.3 408.6 4000 72PBS 1-7/16 AEL207-107 AS207-107 * Thrust Rating is 20% of Radial Rating. A complete PBS unit consists of PBS stamping, MST flangette and AEL/AS Bearings with collar. OTHER BEARING SIZES AND TYPES AVAILABLE ON REQUEST. Recommended shaft tolerance -: Up to 50mm(2")dia. inclusive Nominal 178
BALL BRG UNITS Flanged: 4 Bolt Square Cast Iron: UCF 200 Square Flange Cartridges: UCF 200 with Set Screws Shaft Diameter: 12-90 mm 1/2 to 3-1/2 inches Part No. Example: For Bearing UC 202 Order Complete Unit UCF 202 Unit Shaft Diameter Bearing Dimensions in mm Bolt Hsng Appr No. mm inch No. A E I G L S Z Bi N Size No. Wt. mm Kg UCF201 12 UC201 86 64 15 12 25.5 12 33.3 31.0 12.7 M10 F204 0.67 UCF201-008 12.700 1/2 UC201-008 UCF202-009 14.288 9/16 UC202-009 UCF202 15 UC202 86 64 15 12 25.5 12 33.3 31.0 12.7 M10 F204 0.66 UCF202-010 15.875 5/8 UC202-010 UCF203 17 UC203 86 64 15 12 25.5 12 33.3 31.0 12.7 M10 F204 0.64 UCF203-011 17.462 11/16 UC203-011 UCF204-012 19.050 3/4 UC204-012 86 64 15 12 25.5 12 33.3 31.0 12.7 M10 F204 0.62 UCF204 20 UC204 UCF205-013 20.638 13/16 UC205-013 UCF205-014 22.225 7/8 UC205-014 UCF205-015 23.812 15/16 UC205-015 95 70 16 14 27.0 12 35.7 34.0 14.3 M10 F205 0.85 UCF205 25 UC205 UCF205-100 25.400 1 UC205-100 UCF206-101 26.988 1-1/16 UC206-101 UCF206-102 28.575 1-1/8 UC206-102 UCF206 30 UC206 108 83 18 14 31.0 12 40.2 38.1 15.9 M10 F206 1.14 UCF206-103 30.162 1-3/16 UC206-103 UCF206-104 31.750 1-1/4 UC206-104 UCF207-104 31.750 UC207-104 UCF207-105 33.338 1-5/16 UC207-105 UCF207-106 34.925 1-3/8 UC207-106 117 92 19 16 34.0 14 44.4 42.9 17.5 M12 F207 1.47 UCF207 35 UC207 UCF207-107 36.512 1-7/16 UC207-107 UCF208-107 36.512 1-7/16 UC208-107 UCF208-108 38.100 1-1/2 UC208-108 130 102 21 16 36.0 16 51.2 49.2 19.0 M14 F208 2.10 UCF208-109 39.688 1-9/16 UC208-109 UCF208 40 UC208 UCF209-110 41.275 1-5/8 UC209-110 UCF209-111 42.862 1-11/16 UC209-111 137 105 22 18 38.0 16 52.2 49.2 19.0 M14 F209 2.50 UCF209-112 44.450 1-3/4 UC209-112 UCF209 45 UC209 UCF210-113 46.038 1-13/16 UC210-113 UCF210-114 47.625 1-7/8 UC210-114 UCF210-115 49.212 1-15/16 UC210-115 143 111 22 18 40.0 16 54.6 51.6 19.0 M14 F210 2.60 UCF210 50 UC210 UCF210-200 50.800 UC210-200 UCF211-200 50.800 2 UC211-200 UCF211-201 52.388 2-1/16 UC211-201 UCF211-202 53.975 2-1/8 UC211-202 162 130 25 20 43.0 19 58.4 55.6 22.2 M16 F211 3.60 UCF211 55 UC211 UCF211-203 55.562 2-3/16 UC211-203 UCF212-204 57.150 2-1/4 UC212-204 UCF212-205 58.738 2-5/16 UC212-205 175 143 29 20 48.0 19 68.7 65.1 25.4 M16 F212 4.90 UCF212 60 UC212 UCF212-206 60.325 2-3/8 UC212-206 UCF213-207 61.912 2-7/16 UC213-207 UCF213-208 63.500 2-1/2 UC213-208 187 149 30 20 50.0 19 69.7 65.1 25.4 M16 F213 5.90 UCF213 65 UC213 UCF214-210 66.675 2-5/8 UC214-210 UCF214-211 68.262 2-11/16 UC214-211 193 152 31 24 54.0 19 75.4 74.6 30.2 M16 F214 6.70 UCF214-212 69.850 2-3/4 UC214-212 UCF214 70 UC214 UCF215-213 71.438 2-13/16 UC215-213 UCF215-214 73.025 2-7/8 UC215-214 UCF215-215 74.612 2-15/16 UC215-215 200 159 34 24 56.0 19 78.5 77.8 33.3 M16 F215 7.70 UCF215 75 UC215 UCF215-300 76.200 3 UC215-300 UCF215-302 79.375 3-1/8 UC215-302 UCF216 80 UC216 208 165 34 24 58.0 23 83.3 82.6 33.3 M20 F216 8.20 UCF216-303 80.962 3-3/16 UC216-303 UCF217-304 82.550 3-1/4 UC217-304 220 175 36 26 63.0 23 87.6 85.7 34.1 M20 F217 9.80 UCF217 85 UC217 UCF218-307 87.312 3-7/16 UC218-307 UCF218-308 88.900 3-1/2 UC218-308 235 187 40 26 63.0 23 96.3 96.0 39.7 M20 F218 12.2 UCF218 90 UC218 179
BALL BRG UNITS Flanged: 4 Bolt Square Cast Iron: UCF X00 Square Flange Cartridges: UCF X00 with Set Screws Shaft Diameter: 23.812 101.6 mm 15/16 to 4 inches Part No. Example: For Bearing Order Complete Unit UC X06 UCF X06 Unit Shaft Bearing Dimensions in MM Bolt Hsng Appr No Diameter No A E I G L S Z Bi N Size No. Wt. mm inch mm Kg UCFX05-015 23.812 15/16 UC206-015 UCFX05 25 UCX05 108 83 18 13 30 12 40.2 38.1 15.9 M10 FX05 1.16 UCFX05-100 25.400 1 UC206-100 UCFX06 30 UCX06 UCFX06-103 30.162 1-3/16 UC207-103 117 92 19 14 34 16 44.4 42.9 17.5 M14 FX06 1.25 UCFX06-104 31.750 1-1/4 UC207-104 UCFX07 35 UCX07 130 102 21 14 38 16 51.2 49.2 19.0 M14 FX07 2.00 UCFX07-107 36.512 1-7/16 UC208-107 UCFX08-108 38.100 1-1/2 UC209-108 137 105 22 14 40 19 52.2 49.2 19.0 M16 FX08 2.40 UCFX08 40 UCX08 UCFX09-111 42.862 1-11/16 UC210-111 UCFX09-112 44.450 1-3/4 UC210-112 143 111 23 14 40 19 55.6 51.6 19.0 M16 FX09 2.60 UCFX09 45 UCX09 UCFX10-115 49.212 1-15/16 UC211-115 UCFX10 50 UCX10 162 130 26 20 44 19 59.4 55.6 22.2 M16 FX10 3.80 UCFX10-200 50.800 2 UC211-200 UCFX11 55 UCX11 UCFX11-203 55.562 2-3/16 UC212-203 175 143 29 20 49 19 68.7 65.1 25.4 M16 FX11 4.80 UCFX11-204 57.150 2-1/4 UC212-204 UCFX12 60 UCX12 187 149 34 21 59 19 73.7 65.1 25.4 M16 FX12 6.20 UCFX13-207 61.912 2-7/16 UC214-207 UCFX13-208 63.500 2-1/2 UC214-208 187 149 34 21 59 19 78.4 74.6 30.2 M16 FX13 6.70 UCFX13 65 UCX13 UCFX14-211 68.262 2-11/16 UC215-211 UCFX14-212 69.850 2-3/4 UC215-212 197 152 37 24 60 23 81.5 77.8 33.3 M20 FX14 7.50 UCFX14 70 UCX14 UCFX15-215 74.612 2-15/16 UC216-215 UCFX15 75 UCX15 197 152 40 24 68 23 89.3 82.6 33.3 M20 FX15 8.10 UCFX15-300 76.200 3 UC216-300 UCFX16 80 UCX16 UCFX16-303 80.962 3-3/16 UC217-303 214 171 40 24 70 23 91.6 85.7 34.1 M20 FX16 10.30 UCFX16-304 82.550 3-1/4 UC217-304 UCFX17 85 UCX17 UCFX17-307 87.312 3-7/16 UC218-307 214 171 40 24 70 23 96.3 96.0 39.7 M20 FX17 10.50 UCFX17-308 88.900 3-1/2 UC218-308 UCFX18 90 UCX18 214 171 45 24 76 23 106.1 104.0 42.9 M20 FX18 11.90 UCFX20 100 UCX20 UCFX20-315 100.012 3-15/16 UC221-315 268 211 59 31 97 31 127.3 117.5 49.2 M27 FX20 23.00 UCFX20-400 101.600 4 UC221-400 180
BALL BRG UNITS Square Flange Cartridges: UCF 300 with Set Screws Shaft Diameter: 20.638 140mm 13/16 to 4 inches Part No. Example: For Bearing UC 305 Order Complete Unit UCF 305 Flanged: 4 Bolt Square Cast Iron: UCF 300 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No. Diameter No. A E I G L S Z Bi N Size No. Wt. mm inch mm Kg UCF305-013 20.638 13/16 UC305-013 UCF305-014 22.225 7/8 UC305-014 UCF305-015 23.812 15/16 UC305-015 110 80 16 13 29 16 39 38 15 M14 F305 1.15 UCF305 25 UC305 UCF305-100 25.400 1 UC305-100 UCF306-101 26.988 1-1/16 UC306-101 UCF306-102 28.575 1-1/8 UC306-102 UCF306 30 UC306 125 95 18 15 32 16 44 43 17 M14 F306 1.64 UCF306-103 30.162 1-3/16 UC306-103 UCF306-104 31.750 1-1/4 UC306-104 UCF307-104 31.750 1-1/4 UC307-104 UCF307-105 33.338 1-5/16 UC307-105 UCF307-106 34.925 1-3/8 UC307-106 135 100 20 16 36 19 49 48 19 M16 F307 2.20 UCF307 35 UC307 UCF307-107 36.512 1-7/16 UC307-107 UCF308-107 36.512 1-7/16 UC308-107 UCF308-108 38.100 1-1/2 UC308-108 150 112 23 17 40 19 56 52 19 M16 F308 2.90 UCF308-109 39.688 1-9/16 UC308-109 UCF308 40 UC308 UCF309-110 41.275 1-5/8 UC309-110 UCF309-111 42.862 1-11/16 UC309-111 160 125 25 18 44 19 60 57 22 M16 F309 3.70 UCF309-112 44.450 1-3/4 UC309-112 UCF309 45 UC309 UCF310-113 46.038 1-13/16 UC310-113 UCF310-114 47.625 1-7/8 UC310-114 UCF310-115 49.212 1-15/16 UC310-115 175 132 28 19 48 23 67 61 22 M20 F310 4.70 UCF310 50 UC310 UCF310-200 50.800 2 UC310-200 UCF311-200 50.800 2 UC311-200 UCF311-201 52.388 2-1/16 UC311-201 UCF311-202 53.975 2-1/8 UC311-202 185 140 30 20 52 23 71 66 25 M20 F311 5.80 UCF311 55 UC311 UCF311-203 55.562 2-3/16 UC311-203 UCF312-204 57.150 2-1/4 UC312-204 UCF312-205 58.738 2-5/16 UC312-205 195 150 33 22 56 23 78 71 26 M20 F312 7.60 UCF312 60 UC312 UCF312-206 60.325 2-3/8 UC312-206 UCF313-207 61.912 2-7/16 UC313-207 UCF313-208 63.500 2-1/2 UC313-208 208 166 33 22 58 23 78 75 30 M20 F313 8.30 UCF313 65 UC313 UCF314-210 66.675 2-5/8 UC314-210 UCF314-211 68.262 2-11/16 UC314-211 226 178 36 25 61 25 81 78 33 M22 F314 9.90 UCF314-212 69.850 2-3/4 UC314-212 UCF314 70 UC314 UCF315-213 71.438 2-13/16 UC315-213 UCF315-214 73.025 2-7/8 UC315-214 UCF315-215 74.612 2-15/16 UC315-215 236 184 39 25 66 25 89 82 32 M22 F315 11.20 UCF315 75 UC315 UCF315-300 76.200 3 UC315-300 UCF316-302 79.375 3-1/8 UC316-302 UCF316 80 UC316 250 196 38 27 68 31 90 86 34 M27 F316 13.60 UCF316-303 80.962 3-3/16 UC316-303 UCF317-304 82.550 3-1/4 UC317-304 260 204 44 27 74 31 100 96 40 M27 F317 15.80 UCF317 85 UC317 UCF318-307 87.312 3-7/16 UC318-307 UCF318-308 88.900 3-1/2 UC318-308 280 216 44 30 76 35 100 96 40 M30 F318 20.00 UCF318 90 UC318 UCF319 95 UC319 290 228 59 30 94 35 121 103 41 M30 F319 22.00 UCF319-312 95.250 3-3/4 UC319-312 UCF320 100 UC320 UCF320-315 100.012 3-15/16 UC320-315 310 242 59 32 94 38 125 108 42 M33 F320 27.00 UCF320-400 101.600 4 UC320-400 UCF321 105 UC321 310 242 59 32 94 38 127 112 44 M33 F321 28.00 UCF322 110 UC322 340 266 60 35 96 41 131 117 46 M36 F322 37.00 UCF324 120 UC324 370 290 65 40 110 41 140 126 51 M36 F324 50.00 UCF326 130 UC326 410 320 65 45 115 41 146 135 54 M36 F326 65.00 UCF328 140 UC328 450 350 75 55 125 41 161 145 59 M36 F328 86.00 181
BALL BRG UNITS Flanged: 4 Bolt Square Cast Iron: UKF 200 Square Flange Cartridges UKF 200 + H with Adapter Shaft Diameter: 19.050 80.962 mm 3/4 to 3-3/16 inches Part No. Example: For Bearing UK 205 Order Complete Unit UKF 205 + H2305 (to fit 20mm shaft) Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No Diameter No a e i g l s z L Size No. Wt. mm inch mm Kg UKF205+HE2305 19.050 3/4 UK205 95 70 16 14 27 12 35.5 35 M10 F205 0.88 UKF205+H 2305 20 UKF206+HS2306 22.225 7/8 UKF206+HA2306 23.812 15/16 UK206 108 83 18 14 31 12 39.0 38 M10 F206 1.23 UKF206+H 2306 25 UKF206+HE2306 25.400 1 UKF207+HS2307 28.575 1-1/8 UKF207+H 2307 30 UK207 117 92 19 16 34 14 41.5 43 M12 F207 1.52 UKF207+HA2307 30.162 1-3/16 UKF208+HE2308 31.750 1-1/4 UKF208+HS2308 34.925 1-3/8 UK208 130 102 21 16 36 16 45.5 46 M14 F208 2.00 UKF208+H 2308 35 UKF209+HA2309 36.512 1-7/16 UKF209+HE2309 38.100 1-1/2 UK209 137 105 22 18 38 16 48.0 50 M14 F209 2.50 UKF209+H 2309 40 UKF210+HS2310 41.275 1-5/8 UKF210+HA2310 42.862 1-11/16 UK210 143 111 22 18 40 16 49.5 55 M14 F210 2.80 UKF210+HE2310 44.450 1-3/4 UKF210+H 2310 45 UKF211+HS2311 47.625 1-7/8 UKF211+HA2311 49.212 1-15/16 UK211 162 130 25 20 43 19 53.5 59 M16 F211 3.70 UKF211+H 2311 50 UKF211+HE2311 50.800 2 UKF212+HS2312 53.975 2-1/8 UK212 175 143 29 20 48 19 60.0 62 M16 F212 4.80 UKF212+H 2312 55 UKF213+HA2313 55.562 2-3/16 UKF213+HE2313 57.150 2-1/4 UK213 187 149 30 20 50 19 63.0 65 M16 F213 6.00 UKF213+H 2313 60 UKF213+HS2313 60.325 2-3/8 UKF215+HA2315 61.912 2-7/16 UKF215+HE2315 63.500 2-1/2 UK215 200 159 34 24 56 19 69.5 73 M16 F215 8.00 UKF215+H 2315 65 UKF216+HA2316 68.262 2-11/16 UKF216+HE2316 69.850 2-3/4 UK216 208 165 34 24 58 23 73.0 78 M20 F216 8.70 UKF216+H 2316 70 UKF217+HA2317 74.612 2-15/16 UKF217+H 2317 75 UK217 220 175 36 26 63 23 77.0 82 M20 F217 10.10 UKF217+HE2317 76.200 3 UKF218+HS2318 79.375 3-1/8 UKF218+H 2318 80 3-1/8 UK218 235 187 40 26 68 23 82.5 86 M20 F218 12.70 UKF218+HA2318 80.962 3-3/16 182
BALL BRG UNITS Flanged: 4 Bolt Square Cast Iron: UKF 300 Part No. Example: For Bearing UK 310 Order Complete Unit UKF 310 + H2310 (to fit 45mm shaft) Unit No. with Cast Cover UKF 310 + C + HE2310 (Open) UKF 310 + CE + HE2310 (Closed) Square Flange Cartridges UKF 300 + H with Adapter Shaft Diameter: 19.050 125 mm 3/4-4 inches Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No Diameter No a e i g l s z L Size No Wt. mm inch mm Kg UKF305+HE2305 19.050 3/4 UK305 110 80 16 13 29 16 37.0 35 M16 F305 1.17 UKF305+H 2305 20 UKF306+HS2306 22.225 7/8 UKF306+HA2306 23.812 15/16 UK306 125 95 18 15 32 16 40.5 38 M16 F306 1.66 UKF306+H 2306 25 UKF306+HE2306 25.400 1 UKF307+HS2307 28.575 1-1/8 UKF307+H 2307 30 UK307 135 100 20 16 36 19 44.5 43 M16 F307 2.20 UKF307+HA2307 30.162 1-3/16 UKF308+HE2308 31.750 1-1/4 UKF308+HS2308 34.925 1-3/8 UK308 150 112 23 17 40 19 50.0 46 M16 F308 2.90 UKF308+H 2308 35 UKF309+HA2309 36.512 1-7/16 UKF309+HE2309 38.100 1-1/2 UK309 160 125 25 18 44 19 54.5 50 M16 F309 3.60 UKF309+H 2309 40 UKF310+HS2310 41.275 1-5/8 UKF310+HA2310 42.862 1-11/16 UK310 175 132 28 19 48 23 60.0 55 M20 F310 4.80 UKF310+HE2310 44.450 1-3/4 UKF310+H 2310 45 UKF311+HS2311 47.625 1-7/8 UKF311+HA2311 49.212 1-15/16 UK311 185 140 30 20 52 23 63.5 59 M20 F311 5.80 UKF311+H 2311 50 UKF311+HE2311 50.800 2 UKF312+HS2312 53.975 2-1/8 UK312 195 150 33 22 56 23 69.0 62 M20 F312 7.30 UKF312+H 2312 55 UKF313+HA2313 55.562 2-3/16 UKF313+HE2313 57.150 2-1/4 UK313 208 166 33 22 58 23 71.0 65 M20 F313 8.30 UKF313+H 2313 60 UKF313+HS2313 60.325 2-3/8 UKF315+HA2315 61.912 2-7/16 UKF315+HE2315 63.500 2-1/2 UK315 236 184 39 25 66 25 81.0 73 M22 F315 11.40 UKF315+H 2315 65 UKF316+HA2316 68.262 2-11/16 UKF316+HE2316 69.850 2-3/4 UK316 250 196 38 27 68 31 83.5 78 M27 F316 13.80 UKF316+H 2316 70 UKF317+HA2317 74.612 2-15/16 UKF317+H 2317 75 UK317 260 204 44 27 74 31 92.0 82 M27 F317 15.40 UKF317+HE2317 76.200 3 UKF318+HS2318 79.375 3-1/8 UKF318+H 2318 80 UK318 280 216 44 30 76 35 93.5 86 M30 F318 20.0 UKF318+HA2318 80.962 3-3/16 UKF319+HE2319 82.550 3-1/4 UK319 290 228 59 30 94 35 111.0 90 M30 F319 21.0 UKF319+H 2319 85 UKF320+HE2320 88.900 3-1/2 UK320 310 242 59 32 94 38 115.0 97 M33 F320 27.0 UKF320+H 2320 90 UKF322+H 2322 100 3-15/16 UK322 340 266 60 35 96 41 121.0 105 M36 F322 37.0 UKF322+HE2322 101.60 4 UKF324+H 2324 110 UK324 370 290 65 40 110 41 130.0 112 M36 F324 49.0 UKF326+H 2326 115 UK326 410 320 65 45 115 41 134.0 121 M36 F326 65.0 UKF328+H 2328 125 UK328 450 350 75 55 125 41 148.0 131 M36 F328 86.0 183
BALL BRG UNITS Flanged: 4 Bolt Square Cast Iron: UELF 200 Square Flange Cartridges UELF 200 with Eccentric Locking Collar Shaft Diameter: 12-60.325 mm 1/2 to 2-3/8 inches Part No. Example: For Bearing UEL 205 Order Complete Unit UELF 205 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No Diameter No A E I G L S Z Bi N Size No Wt. mm inch mm Kg UELF201 12 UEL201 76 54 17 12 27 10.5 40.4 37.3 13.9 M10 F203 0.60 UELF201-008 12.700 1/2 UEL201-008 UELF202-009 14.288 9/16 UEL202-009 UELF202 15 UEL202 76 54 17 12 27 10.5 40.4 37.3 13.9 M10 F203 0.58 UELF202-010 15.875 5/8 UEL202-010 UELF203 17 UEL203 76 54 17 12 27 10.5 40.4 37.3 13.9 M10 F203 0.57 UELF203-011 17.462 11/16 UEL203-011 UELF204-012 19.050 3/4 UEL204-012 86 63.5 19 12 29.5 12 45.6 43.7 17.1 M10 F204 0.71 UELF204 20 UEL204 UELF205-013 20.638 13/16 UEL205-013 UELF205-014 22.225 7/8 UEL205-014 UELF205-015 23.812 15/16 UEL205-015 95 70 19 14 30 12 45.9 44.4 17.5 M10 F205 0.89 UELF205 25 UEL205 UELF205-100 25.400 1 UEL205-100 UELF206-101 26.988 1-1/16 UEL206-101 UELF206-102 28.575 1-1/8 UEL206-102 UELF206 30 UEL206 108 82.5 20 14 33 12 50.1 48.4 18.3 M10 F206 1.20 UELF206-103 30.162 1-3/16 UEL206-103 UELF206-104 31.750 1-1/4 UEL206-104 UELF207-104 31.750 1-1/4 UEL207-104 UELF207-105 33.338 1-5/16 UEL207-105 UELF207-106 34.925 1-3/8 UEL207-106 117 92 21 16 36 14 53.3 51.1 18.8 M12 F207 1.59 UELF207 35 UEL207 UELF207-107 36.512 1-7/16 UEL207-107 UELF208-107 36.512 1-7/16 UEL208-107 UELF208-108 38.100 1-1/2 UEL208-108 130 101.5 24 16 39 14 58.9 56.3 21.4 M14 F208 2.20 UELF208-109 39.688 1-9/16 UEL208-109 UELF208 40 UEL208 UELF209-110 41.275 1-5/8 UEL209-110 UELF209-111 42.862 1-11/16 UEL209-111 137 105 24 18 40 16 58.9 56.3 21.4 M14 F209 2.50 UELF209-112 44.450 1-3/4 UEL209-112 UELF209 45 UEL209 UELF210-113 46.038 1-13/16 UEL210-113 UELF210-114 47.625 1-7/8 UEL210-114 UELF210-115 49.212 1-15/16 UEL210-115 143 111 28 18 46 16 66.1 62.7 24.6 M14 F210 2.80 UELF210 50 UEL210 UELF210-200 50.800 2 UEL210-200 UELF211-200 50.800 2 UEL211-200 UELF211-201 52.388 2-1/16 UEL211-201 UELF211-202 53.975 2-1/8 UEL211-202 162 130 31 20 49 18 74.6 71.4 27.8 M16 F211 3.90 UELF211 55 UEL211 UELF211-203 55.562 2-3/16 UEL211-203 UELF212-204 57.150 2-1/4 UEL212-204 UELF212-205 58.738 2-5/16 UEL212-205 175 143 34 20 53 18 80.8 77.8 31 M16 F212 5.10 UELF212 60 UEL212 UELF212-206 60.325 2-3/8 UEL212-206 184
BALL BRG UNITS Round Flange Cartridges with Centering Pilots UCFC 200 with Set Screws Shaft Diameter: 12 90 mm 1/2 to 3-1/2 inches Flanged: 4 Bolt Round Cast Iron: UCFC 200 Part No. Example: For Bearing UC 205 Order Complete Unit UCFC 205 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No Diameter No a p e i s j k g f z Bi N Size No Wt. mm inch mm Kg UCFC201 12 UC201 UCFC201-008 12.700 1/2 UC201-008 100 78 55.1 10 12 5 7 20.5 62 28.3 31.0 12.7 M10 FC204 0.73 UCFC202-009 14.288 9/16 UC202-009 UCFC202 15 UC202 100 78 55.1 10 12 5 7 20.5 62 28.3 31.0 12.7 M10 FC204 0.71 UCFC202-010 15.875 5/8 UC202-010 UCFC203 17 UC203 100 78 55.1 10 12 5 7 20.5 62 28.3 31.0 12.7 M10 FC204 0.70 UCFC203-011 17.462 11/16 UC203-011 UCFC204-012 19.050 3/4 UC204-012 100 78 55.1 10 12 5 7 20.5 62 28.3 31.0 12.7 M10 FC204 0.68 UCFC204 20 UC204 UCFC205-013 20.638 13/16 UC205-013 UCFC205-014 22.225 7/8 UC205-014 UCFC205-015 23.812 15/16 UC205-015 115 90 63.6 10 12 6 7 21.0 70 29.7 34.0 14.3 M10 FC205 0.94 UCFC205 25 UC205 UCFC205-100 25.400 1 UC205-100 UCFC206-101 26.988 1-1/16 UC206-101 UCFC206-102 28.575 1-1/8 UC206-102 UCFC206 30 UC206 125 100 70.7 10 12 8 8 23.0 80 32.2 38.1 15.9 M10 FC206 1.23 UCFC206-103 30.162 1-3/16 UC206-103 UCFC206-104 31.750 1-1/4 UC206-104 UCFC207-104 31.750 1-1/4 UC207-104 UCFC207-105 33.338 1-5/16 UC207-105 UCFC207-106 34.925 1-3/8 UC207-106 135 110 77.8 11 14 8 9 26.0 90 36.4 42.9 17.5 M12 FC207 1.58 UCFC207 35 UC207 UCFC207-107 36.512 1-7/16 UC207-107 UCFC208-107 36.512 1-7/16 UC208-107 UCFC208-108 38.100 1-1/2 UC208-108 145 120 84.8 11 14 10 9 26.0 100 41.2 49.2 19.0 M12 FC208 1.92 UCFC208-109 39.688 1-9/16 UC208-109 UCFC208 40 UC208 UCFC209-110 41.275 1-5/8 UC209-110 UCFC209-111 42.862 1-11/16 UC209-111 160 132 93.3 10 16 12 14 26.0 105 40.2 49.2 19.0 M14 FC209 2.70 UCFC209-112 44.450 1-3/4 UC209-112 UCFC209 45 UC209 UCFC210-113 46.038 1-13/16 UC210-113 UCFC210-114 47.625 1-7/8 UC210-114 UCFC210-115 49.212 1-15/16 UC210-115 165 138 97.6 10 16 12 14 28.0 110 42.6 51.6 19.0 M14 FC210 2.80 UCFC210 50 UC210 UCFC210-200 50.800 2 UC210-200 UCFC211-200 50.800 2 UC211-200 UCFC211-201 52.388 2-1/16 UC211-201 UCFC211-202 53.975 2-1/8 UC211-202 185 150 106.1 13 19 12 15 31.0 125 46.4 55.6 22.2 M16 FC211 3.90 UCFC211 55 UC211 UCFC211-203 55.562 2-3/16 UC211-203 UCFC212-204 57.150 2-1/4 UC212-204 UCFC212-205 58.738 2-5/16 UC212-205 195 160 113.1 17 19 12 15 36.0 135 56.7 65.1 25.4 M16 FC212 4.90 UCFC212 60 UC212 UCFC212-206 60.325 2-3/8 UC212-206 UCFC213-207 61.912 2-7/16 UC213-207 UCFC213-208 63.500 2-1/2 UC213-208 205 170 120.2 16 19 14 15 36.0 145 55.7 65.1 25.4 M16 FC213 5.50 UCFC213 65 UC213 UCFC214-210 66.675 2-5/8 UC214-210 UCFC214-211 68.262 2-11/16 UC214-211 215 177 125.1 17 19 14 18 40.0 150 61.4 74.6 30.2 M16 FC214 7.00 UCFC214-212 69.850 2-3/4 UC214-212 UCFC214 70 UC214 UCFC215-213 71.438 2-13/16 UC215-213 UCFC215-214 73.025 2-7/8 UC215-214 UCFC215-215 74.612 2-15/16 UC215-215 220 184 130.1 18 19 16 18 40.0 160 62.5 77.8 33.3 M16 FC215 7.50 UCFC215 75 UC215 UCFC215-300 76.200 3 UC215-300 UCFC216-302 79.375 3-1/8 UC216-302 UCFC216 80 UC216 240 200 141.4 18 23 16 18 42.0 170 67.3 82.6 33.3 M20 FC216 8.80 UCFC216-303 80.962 3-3/16 UC216-303 UCFC217-304 82.550 3-1/4 UC217-304 250 208 147.1 18 23 18 20 45.0 180 69.6 85.7 34.1 M20 FC217 10.80 UCFC217 85 UC217 UCFC218-307 87.312 3-7/16 UC218-307 UCFC218-308 88.900 3-1/2 UC218-308 265 220 155.5 22 23 18 20 50.0 190 78.3 96.0 39.7 M20 FC218 13.00 UCFC218 90 UC218 185
BALL BRG UNITS Round Flange Cartridges with Centering Pilots UCFC X00 with Set Screws Shaft Diameter: 23.812 101.600 mm 15/16 to 4 inches Flanged: 4 Bolt Round Cast Iron: UCFC X00 Part No. Example: For Bearing UC X06 Order Complete Unit UCFC X06 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No Diameter No a p e i s j k g f z Bi n Size No Wt. mm inch mm Kg UCFCX05-015 23.812 15/16 UC206-015 UCFCX05 25 UCX05 111 92 65.0 10 9.5 6.0 9.5 24.0 76 32.2 38.1 15.9 M8 FCX05 1.10 UCFCX05-100 25.400 1 UC206-100 UCFCX06 30 UCX06 UCFCX06-103 30.162 1-3/16 UC207-103 127 105 74.2 8 12.0 9.5 9.5 22.5 85 33.4 42.9 17.5 M10 FCX06 1.46 UCFCX06-104 31.750 1-1/4 UC207-104 UCFCX07 35 UCX07 133 111 78.5 9 12.0 11.0 11.0 26.0 92 39.2 49.2 19.0 M10 FCX07 1.86 UCFCX07-107 36.512 1-7/16 UC208-107 UCFCX08-108 38.100 1-1/2 UC209-108 133 111 78.5 9 12.0 11.0 11.0 26.0 92 39.2 49.2 19.0 M10 FCX08 1.95 UCFCX08 40 UCX08 UCFCX09-111 42.862 1-11/16 UC210-111 UCFCX09-112 44.450 1-3/4 UC210-112 155 130 91.9 8 14.0 12.0 11.0 25.0 108 40.6 51.6 19.0 M12 FCX09 2.50 UCFCX09 45 UCX09 UCFCX10-115 49.212 1-15/16 UC211-115 UCFCX10 50 UCX10 162 136 96.2 7 14.0 16.0 11.0 25.0 118 40.4 55.6 22.2 M12 FCX10 3.00 UCFCX10-200 50.800 2 UC211-200 UCFCX11 55 UCX11 UCFCX11-203 55.562 2-3/16 UC212-203 180 152 107.5 4 16.0 22.0 13.0 26.0 127 43.7 65.1 25.4 M14 FCX11 4.10 UCFCX11-204 57.150 2-1/4 UC212-204 UCFCX12 60 UCX12 194 165 116.7 11 16.0 20.0 14.0 33.0 140 50.7 65.1 25.4 M14 FCX12 5.20 UCFCX13-207 61.912 2-7/16 UC214-207 UCFCX13-208 63.500 2-1/2 UC214-208 194 165 116.7 11 16.0 20.0 14.0 33.0 140 55.4 74.6 30.2 M14 FCX13 5.50 UCFCX13 65 UCX13 UCFCX14-211 68.262 2-11/16 UC215-211 UCFCX14-212 69.850 2-3/4 UC215-212 222 190 134.3 14 19.0 20.0 14.0 36.0 164 58.5 77.8 33.3 M16 FCX14 7.10 UCFCX14 70 UCX14 UCFCX15-215 74.612 2-15/16 UC216-215 UCFCX15 75 UCX15 222 190 134.3 12 19.0 22.0 16.0 35.0 164 61.3 82.6 33.3 M16 FCX15 7.60 UCFCX15-300 76.200 3 UC216-300 UCFCX16 80 UCX16 UCFCX16-303 80.962 3-3/16 UC217-303 260 219 154.8 10 23.0 25.0 19.0 36.0 186 61.6 85.7 34.1 M20 FCX16 11.20 UCFCX16-304 82.550 3-1/4 UC217-304 UCFCX17 85 UCX17 UCFCX17-307 87.312 3-7/16 UC218-307 260 219 154.8 10 23.0 25.0 19.0 36.0 186 66.3 96.0 39.7 M20 FCX17 11.40 UCFCX17-308 88.900 3-1/2 UC218-308 UCFCX18 90 UCX18 260 219 154.8 12 23.0 28.0 19.0 43.0 186 73.1 104.0 42.9 M20 FCX18 12.80 UCFCX20 100 UCX20 UCFCX20-315 100.012 3-15/16 UC221-315 276 238 168.3 22 23.0 28.0 22.0 66.0 206 90.3 117.5 49.2 M20 FCX20 17.70 UCFCX20-400 101.600 4 UC221-400 Note: Pressed Steel covers are also available. Please contact any branch near you. 186
BALL BRG UNITS Round Flange Cartridges with Centering Pilots UKFC 200 + H with Adapter Shaft Diameter: 19.050 80.962 mm 3/4 to 3-3/16 inches Flanged: 4 Bolt Round Cast Iron: UKFC 200 Part No. Example: For Bearing UK 208 Order Complete Unit UKFC 208 + H2308 (to fit 35mm shaft) Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No Diameter No a p e i s j k g f z L Size No Wt. mm inch mm Kg UKFC205+HE2305 19.050 3/4 UK205 115 90 63.6 10 12 6 7 21 70 29.5 35 M10 FC205 0.98 UKFC205+H 2305 20 UKFC206+HS2306 22.225 7/8 UKFC206+HA2306 23.812 15/16 UK206 125 100 70.7 10 12 8 8 23 80 31.0 38 M10 FC206 1.31 UKFC206+H 2306 25 UKFC206+HE2306 25.400 1 UKFC207+HS2307 28.575 1-1/8 UKFC207+H 2307 30 UK207 135 110 77.8 11 14 8 9 26 90 33.5 43 M12 FC207 1.62 UKFC207+HA2307 30.162 1-3/16 UKFC208+HE2308 31.750 1-1/4 UKFC208+HS2308 34.925 1-3/8 UK208 145 120 84.8 11 14 10 9 26 100 35.5 46 M12 FC208 1.93 UKFC208+H 2308 35 UKFC209+HA2309 36.512 1-7/16 UKFC209+HE2309 38.100 1-1/2 UK209 160 132 93.3 10 16 12 14 26 105 36.0 50 M14 FC209 2.80 UKFC209+H 2309 40 UKFC210+HS2310 41.275 1-5/8 UKFC210+HA2310 42.862 1-11/16 UK210 165 138 97.6 10 16 12 14 28 110 37.5 55 M14 FC210 3.10 UKFC210+HE2310 44.450 1-3/4 UKFC210+H 2310 45 UKFC211+HS2311 47.625 1-7/8 UKFC211+HA2311 49.212 1-15/16 UK211 185 150 106.1 13 19 12 15 31 125 41.5 59 M16 FC211 4.00 UKFC211+H 2311 50 UKFC211+HE2311 50.800 2 UKFC212+HS2312 53.975 2-1/8 UK212 195 160 113.1 17 19 12 15 36 135 48.0 62 M16 FC212 4.80 UKFC212+H 2312 55 UKFC213+HA2313 55.562 2-3/16 UKFC213+HE2313 57.150 2-1/4 UK213 205 170 120.2 16 19 14 15 36 145 49.0 65 M16 FC213 5.50 UKFC213+H 2313 60 UKFC213+HS2313 60.325 2-3/8 UKFC215+HA2315 61.912 2-7/16 UKFC215+HE2315 63.500 2-1/2 UK215 220 184 130.1 18 19 16 18 40 160 53.5 73 M16 FC215 7.90 UKFC215+H 2315 65 UKFC216+HA2316 68.262 2-11/16 UKFC216+HE2316 69.850 2-3/4 UK216 240 200 141.4 18 23 16 18 42 170 57.0 78 M20 FC216 9.30 UKFC216+H 2316 70 UKFC217+HA2317 74.612 2-15/16 UKFC217+H 2317 75 UK217 250 208 147.1 18 23 18 20 45 180 59.0 82 M20 FC217 11.00 UKFC217+HE2317 76.200 3 UKFC218+HS2318 79.375 3-1/8 UKFC218+H 2318 80 UK218 265 220 155.5 22 23 18 20 50 190 64.5 86 M20 FC218 13.50 UKFC218+HA2318 80.962 3-3/16 Note: Pressed Steel covers are also available. Please contact any branch near you for details. 187
BALL BRG UNITS Flanged: Pressed Metal MST, MS MST Part No. Example: For Bearing AEL204-012 Order Housing 47MST Dimensions in mm N ** Stamp* Brg. Stamp Shaft Bearing Hole Flange Radl Limit Size Size Number Width Bolt Hole Load Speed AEL AS A B C D E F H J1 K1 L Size Dia. Rate RPM inch mm mm kgf/lbf 40MST 12 AEL201 AS201 40MST 1/2 AEL201-008 AS201-008 58.7 81.0 7.1 63.5 7.1 49.2 1.90 23.8 5.6 28.6 6.4 10.3 272.4 8300 40MST 15 AEL202 AS202 40MST 5/8 AEL202-010 AS202-010 47MST 20 AEL204 AS204 47MST 3/4 AEL204-012 AS204-012 66.7 90.5 7.9 71.4 8.7 55.6 2.10 25.0 6.4 33.3 7.9 12.7 317.8 6800 52MST 25 AEL205 AS205 52MST 7/8 AEL205-014 AS205-014 52MST 15/16 AEL205-015 AS205-015 71.0 95.3 8.7 76.2 8.7 60.3 2.10 25.0 7.1 38.1 7.9 12.7 363.2 6000 52MST 1 AEL205-100 AS205-100 62MST 30 AEL206 AS206 62MST 1-1/16 AEL206-101 AS206-101 62MST 1-1/8 AEL206-102 AS206-102 84.1 112.7 8.7 90.5 10.3 71.4 2.64 29.0 6.8 44.5 9.5 15.1 499.4 4800 62MST 1-3/16 AEL206-103 AS206-103 62MST 1-1/4 AEL206-104 AS206-104 72MST 35 AEL207 AS207 72MST 1-1/4 AEL207-104 AS207-104 72MST 1-3/8 AEL207-106 AS207-106 93.7 125.4 11.1 100.0 10.3 81.0 2.64 32.1 6.8 55.6 9.5 15.1 635.6 4000 72MST 1-7/16 AEL207-107 AS207-107 * Thrust Ratings are 30% of radial load ratings ** To clear square shank Recommended shaft tolerance -: Up to 50mm(2") dia. inclusive Nominal to -.0127mm(.0005") Over 50mm(2") dia. Nominal to -.0254mm(.0010") These tolerances correspond to those of precision ground shafting. Commercial grade bright mild steel shafting suitable for most applications. MS Part No. Example: For Bearing AEL204-012 Order Housing 47MS Note: AEL = Eccentric Collar Locking AS = Set Screw Locking Dimensions in mm N ** Stamp* Brg. Stamp Shaft Bearing Hole Flange Radl Limit Size Size Number Width Bolt Hole Load Speed AEL AS B C D E F H J1 K1 L Size Dia. Rate RPM inch mm mm kgf/lbf 40MS 12 AEL201 AS201 40MS 1/2 AEL201-008 AS201-008 81.0 7.1 63.5 7.1 49.2 1.99 23.8 5.6 28.6 6.4 10.3 272.4 8300 40MS 15 AEL202 AS202 40MS 5/8 AEL202-010 AS202-010 47MS 20 AEL204 AS204 47MS 3/4 AEL204-012 AS204-012 90.5 7.9 71.4 8.7 55.6 1.99 25.0 6.4 33.3 7.9 12.7 317.8 6800 52MS 25 AEL205 AS205 52MS 7/8 AEL205-014 AS205-014 52MS 15/16 AEL205-015 AS205-015 95.3 8.7 76.2 8.7 60.3 1.99 25.0 7.1 38.1 7.9 12.7 363.2 6000 52MS 1 AEL205-100 AS205-100 62MS 30 AEL206 AS206 62MS 1-1/16 AEL206-101 AS206-101 62MS 1-1/8 AEL206-102 AS206-102 112.7 8.7 90.5 10.3 71.4 2.52 29.0 6.8 44.5 9.5 15.1 499.4 4800 62MS 1-3/16 AEL206-103 AS206-103 62MS 1-1/4 AEL206-104 AS206-104 72MS 35 AEL207 AS207 72MS 1-1/4 AEL207-104 AS207-104 72MS 1-3/8 AEL207-106 AS207-106 122.2 9.5 100.0 10.3 81.0 2.52 31.8 7.5 55.6 9.5 15.1 635.6 4000 72MS 1-7/16 AEL207-107 AS207-107 *80MS 40 AEL208 AS208 *80MS 1-1/2 AEL208-108 AS208-108 132.2 10.3 119.1 13.5 90.5 3.18 36.1 7.5 60.3 12.7 19.5 771.8 3600 *85MS 45 AEL209 AS209 *85MS 1-3/4 AEL209-112 AS209-112 149.2 11.1 120.6 13.5 96.8 3.18 36.1 7.5 63.5 12.7 19.5 771.8 3300 *100MS 55 AEL211 AS211 *100MS 2 AEL211-200 AS211-200 166.7 11.9 138.1 13.5 112.7 3.99 36.5 8.3 76.2 12.7 19.5 1044.2 2800 **Thrust ratings are 30% of radial load ratings. *80MS to 100MS stampings have four equally spaced bolt holes. Also available as a re-lubricatable unit - Series 52MSGN, etc. Recommended shaft tolerance -: Up to 50mm(2 ) dia. inclusive Nominal to.0127 188
BALL BRG UNITS Oval 2-Bolt Cartridges: UCFL 200 with Set Screws Shaft Diameter: 12-90 mm 1/2 to 3-1/2 inches Flanged: 2 Bolt Hole Cast Iron: UCFL 200 Part No. Example: For Bearing UC 205 Order Complete Unit UCFL 205 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No Diameter No a e i g l s b z Bi n Size No Wt. mm inch mm Kg UCFL201 12 UC201 113 90 15 12 25.5 12 60 33.3 31 12.7 M10 FL204 0.51 UCFL201-008 12.700 1/2 UC201-008 UCFL202-009 14.288 9/16 UC202-009 UCFL202 15 UC202 113 90 15 12 25.5 12 60 33.3 31 12.7 M10 FL204 0.49 UCFL202-010 15.875 5/8 UC202-010 UCFL203 17 UC203 113 90 15 12 25.5 12 60 33.3 31 12.7 M10 FL204 0.48 UCFL203-11 17.462 11/16 UC203-011 UCFL204-012 19.050 3/4 UC204-012 113 90 15 12 25.5 12 60 33.3 31 12.7 M10 FL204 0.46 UCFL204 20 UC204 UCFL205-013 20.638 13/16 UC205-013 UCFL205-014 22.225 7/8 UC205-014 UCFL205-015 23.812 15/16 UC205-015 130 99 16 14 27 16 68 35.7 34 14.3 M14 FL205 0.65 UCFL205 25 UC205 UCFL205-100 25.400 1 UC205-100 UCFL206-101 26.988 1-1/16 UC206-101 UCFL206-102 28.575 1-1/8 UC206-102 UCFL206 30 UC206 148 117 18 14 31 16 80 40.2 38.1 15.9 M14 FL206 0.95 UCFL206-103 30.162 1-3/16 UC206-103 UCFL206-104 31.750 1-1/4 UC206-104 UCFL207-104 31.750 1-1/4 UC207-104 UCFL207-105 33.338 1-5/16 UC207-105 161 130 19 16 34 16 90 44.4 42.9 17.5 M14 FL207 1.32 UCFL207-106 34.925 1-3/8 UC207-106 UCFL207 35 UC207 UCFL207-107 36.512 1-7/16 UC207-107 UCFL208-107 36.512 1-7/16 UC208-107 UCFL208-108 38.100 1-1/2 UC208-108 175 144 21 16 36 16 100 51.2 49.2 19 M14 FL208 1.74 UCFL208-109 39.688 1-9/16 UC208-109 UCFL208 40 UC208 UCFL209-110 41.275 1-5/8 UC209-110 UCFL209-111 42.862 1-11/16 UC209-111 188 148 22 18 38 19 108 52.2 49.2 19 M16 FL209 2.20 UCFL209-112 44.450 1-3/4 UC209-112 UCFL209 45 UC209 UCFL210-113 46.038 1-13/16 UC210-113 UCFL210-114 47.625 1-7/8 UC210-114 UCFL210-115 49.212 1-15/16 UC210-115 197 157 22 18 40 19 115 54.6 51.6 19 M16 FL210 2.40 UCFL210 50 UC210 UCFL210-200 50.800 2 UC210-200 UCFL211-200 50.800 2 UC211-200 UCFL211-201 52.388 2-1/16 UC211-201 224 184 25 20 43 19 130 58.4 55.6 22.2 M16 FL211 3.40 UCFL211-202 53.975 2-1/8 UC211-202 UCFL211 55 UC211 UCFL211-203 55.562 2-3/16 UC211-203 UCFL212-204 57.150 2-1/4 UC212-204 UCFL212-205 58.738 2-5/16 UC212-205 250 202 29 20 48 23 140 68.7 65.1 25.4 M20 FL212 4.40 UCFL212 60 UC212 UCFL212-206 60.325 2-3/8 UC212-206 UCFL213-207 61.912 2-7/16 UC213-207 UCFL213-208 63.500 2-1/2 UC213-208 258 210 30 24 50 23 155 69.7 65.1 25.4 M20 FL213 5.50 UCFL213 65 UC213 UCFL214-210 66.675 2-5/8 UC214-210 UCFL214-211 68.262 2-11/16 UC214-211 265 216 31 24 54 23 160 75.4 74.6 30.2 M20 FL214 6.50 UCFL214-212 69.850 2-3/4 UC214-212 UCFL214 70 UC214 UCFL215-213 71.438 2-13/16 UC215-213 UCFL215-214 73.025 2-7/8 UC215-214 275 225 34 24 56 23 165 78.5 77.8 33.3 M20 FL215 6.90 UCFL215-215 74.612 2-15/16 UC215-215 UCFL215 75 UC215 UCFL215-300 76.200 3 UC215-300 UCFL216-302 79.375 3-1/8 UC216-302 UCFL216 80 UC216 290 233 34 24 58 25 180 83.3 82.6 33.3 M22 FL216 8.40 UCFL216-303 80.962 3-3/16 UC216-303 UCFL217-304 82.550 3-1/4 UC217-304 305 248 36 26 63 25 190 87.6 85.7 34.1 M22 FL217 10.10 UCFL217 85 UC217 UCFL218-307 87.312 3-7/16 UC218-307 320 265 40 26 68 25 205 96.3 96 39.7 M22 FL218 12.5 UCFL218-308 88.900 3-1/2 UC218-308 UCFL218 90 UC218 189
BALL BRG UNITS Flanged: 2 Bolt Hole Cast Iron: UKFL 200 Oval 2-Bolt Cartridges: UKFL 200 + H with Set Screws Shaft Diameter: 20 80mm 3/4 to 3-3/16 inches Part No. Example: For Bearing UK 208 Order Complete Unit UKFL 208 + H23 (to fit 35mm shaft) Unit Shaft Diameter Bearing Dimensions in mm Bolt Housing Approx No. mm inch No. a e i g l s b z L Size No. Wt. mm Kg UKFL205+HE2305 19.050 3/4 UK205 130 99 16 14 27 16 68 35.5 35 M14 FL205 0.69 UKFL205+H 2305 20 UKFL206+HS2306 22.225 7/8 UKFL206+HA2306 23.812 15/16 UK206 148 117 18 14 31 16 80 39.0 38 M14 FL206 1.03 UKFL206+H 2306 25 UKFL206+HE2306 25.400 1 UKFL207+HS2307 28.575 1-1/8 UK207 161 130 19 16 34 16 90 41.5 43 M14 FL207 1.36 UKFL207+H 2307 30 UKFL207+HA2307 30.162 1-3/16 UKFL208+HE2308 31.750 1-1/4 UK208 175 144 21 16 36 16 100 45.5 46 M14 FL208 1.75 UKFL208+HS2308 34.925 1-3/8 UKFL208+H 2308 35 UKFL209+HA2309 36.512 1-7/16 UK209 188 148 22 18 38 19 108 48.0 50 M16 FL209 2.20 UKFL209+HE2309 38.100 1-1/2 UKFL209+H 2309 40 UKFL210+HS2310 41.275 1-5/8 UK210 197 157 22 18 40 19 115 49.5 55 M16 FL210 2.70 UKFL210+HA2310 42.862 1-11/16 UKFL210+HE2310 44.450 1-3/4 UKFL210+H 2310 45 UKFL211+HS2311 47.625 1-7/8 UK211 224 184 25 20 43 19 130 53.5 59 M16 FL211 3.50 UKFL211+HA2311 49.212 1-15/16 UKFL211+H 2311 50 UKFL211+HE2311 50.800 2 UK212 250 202 29 20 48 23 140 60.0 62 M20 FL212 4.30 UKFL212+HS2312 53.975 2-1/8 UKFL212+H 2312 55 UKFL213+HA2313 55.562 2-3/16 UK213 258 210 30 24 50 23 155 63.0 65 M20 FL213 5.50 UKFL213+HE2313 57.150 2-1/4 UKFL213+H 2313 60 UKFL213+HS2313 60.325 2-3/8 UKFL215+HA2315 61.912 2-7/16 UK215 275 225 34 24 56 23 165 69.5 73 M20 FL215 7.30 UKFL215+HE2315 63.500 2-1/2 UKFL215+H 2315 65 UKFL216+HA2316 68.262 2-11/16 UK216 290 233 34 24 58 25 180 73.0 78 M22 FL216 8.90 UKFL216+HE2316 69.850 2-3/4 UKFL216+H 2316 70 UKFL217+HA2317 74.612 2-15/16 UK217 305 248 36 26 63 25 190 77.0 82 M22 FL217 10.30 UKFL217+H 2317 75 UKFL217+HE2317 76.200 3 UKFL218+HS2318 79.375 3-1/8 UK218 320 265 40 26 68 25 205 82.5 86 M22 FL218 13.00 UKFL218+H 2318 80 UKFL218+HA2318 80.962 3-3/16 Note: Pressed Steel covers are also available. Please contact any branch near you for details. 190
BALL BRG UNITS Flanged: 2 Bolt Hole Cast Iron: FD 200 AELFD 200 Part No. Example: For Bearing AEL205-100 Order Housing FD205 Housing Shaft Bearing Dimension in mm Bolt Hsg. No Size Number A C E F H L P Size Wt. LS inch mm mm kg/lb RPM FD203 12 AEL201 FD203 1/2 AEL201-008 81.0 14.7 63.5 28.6 58.7 30.2 7.9 6.4 0.18 8300 FD203 15 AEL202 FD203 5/8 AEL202-010 FD204 20 AEL204 FD204 3/4 AEL204-012 90.5 17.1 71.4 33.3 66.7 33.0 9.5 6.4 0.27 6800 FD205 25 AEL205 FD205 7/8 AEL205-014 FD205 15/16 AEL205-015 95.3 17.5 76.2 38.1 71.0 33.3 9.9 7.9 0.27 6000 FD205 1 AEL205-100 FD206 30 AEL206 FD206 1-1/16 AEL206-101 FD206 1-1/8 AEL206-102 112.7 20.6 90.5 44.5 84.1 37.7 11.1 9.5 0.45 4800 FD206 1-3/16 AEL206-103 FD206 1-1/4 AEL206-104 FD207 35 AEL207 FD207 1-1/4 AEL207-104 FD207 1-3/8 AEL207-106 125.4 22.2 100.0 54.0 93.7 42.1 12.7 9.5 0.59 4000 FD207 1-7/16 AEL207-107 OTHER BEARING SIZES AND TYPES AVAILABLE ON REQUEST. Recommended shaft tolerance -: Up to 50mm(2") dia. inclusive Nominal to -.0127mm(.0005") Over 50mm(2")dia. Nominal to -.0254mm(.0010") These tolerances correspond to those of precision ground. ASFD 200 Part No. Example: For Bearing AS204 Order Complete Unit ASFD204J Housing Shaft Bearing Dimensions in mm Bolt Appr No Diameter No A E I G L S B Bi N Size Wt. mm inch mm Kg FD201 12 AS201 81 63.5 9.5 9.5 18.0 8 56 22.0 6.0 M6 0.27 FD201 12.700 1/2 AS201-008 FD202J 14.288 9/16 AS202-009 FD202J 15 AS202 81 63.5 9.5 9.5 18.0 8 56 22.0 6.0 M6 0.26 FD202J 15.875 5/8 AS202-010 FD203J 17 AS203 81 63.5 9.5 9.5 18.0 8 56 22.0 6.0 M6 0.25 FD203J 17.462 11/16 AS203-011 FD204J 19.050 3/4 AS204 90 71.5 11.0 11.0 20.0 10 63 24.7 7.0 M8 0.30 FD204J 20 AS204-012 FD205J 20.638 13/16 AS205-013 FD205J 22.225 7/8 AS205-014 95 76.0 11.0 11.0 20.0 10 69 27.0 7.5 M8 0.40 FD205J 23.812 15/16 AS205-015 FD205J 25 AS205 FD205J 25.400 1 AS205-100 FD206J 26.988 1-1/16 AS206-101 FD206J 28.575 1-1/8 AS206-102 FD206J 30 AS206 113 90.5 12.0 12.0 22.5 12 79 30.3 8.0 M10 0.56 FD206J 30.162 1-3/16 AS206-103 FD206J 31.750 1-1/4 AS206-104 FD207J 31.750 1-1/4 AS207-104 FD207J 33.338 1-5/16 AS207-105 FD207J 34.925 1-3/8 AS207-106 122 100.0 13.0 13.0 24.0 12 89 32.9 8.5 M10 0.78 FD207J 35 AS207 FD208J 36.512 1-7/16 AS208-107 191
BALL BRG UNITS Special Flanged Units UCFA 200 Sector Flange Cartridges UCFA 200 with Set Screws Shaft Diameter: 12 55.562 mm Part No. Example: For Bearing UC 206 Order Complete Unit UCFA 206 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No Diameter No. A E I G L S S1 S2 B F Z Bi N Size No Wt. mm inch mm Kg UCFA201 12 UC201 102 78 15 12 25.5 10 10 40 60 54 33.3 31.0 12.7 M8 FA204 0.45 UCFA201-008 12.700 1/2 UC201-008 UCFA202-009 14.288 9/16 UC202-009 UCFA202 15 UC202 102 78 15 12 25.5 10 10 40 60 54 33.3 31.0 12.7 M8 FA204 0.44 UCFA202-010 15.875 5/8 UC202-010 UCFA203 17 UC203 102 78 15 12 25.5 10 10 40 60 54 33.3 31.0 12.7 M8 FA204 0.43 UCFA203-011 17.462 11/16 UC203-011 UCFA204-012 19.050 3/4 UC204-012 102 78 15 12 25.5 10 10 40 60 54 33.3 31.0 12.7 M8 FA204 0.40 UCFA204 20 UC204 UCFA205-013 20.638 13/16 UC205-013 UCFA205-014 22.225 7/8 UC205-014 UCFA205-015 23.812 15/16 UC205-015 125 98 16 14 27.0 12 13 51 68 65 35.7 34.0 14.3 M10 FA205 0.63 UCFA205 25 UC205 UCFA205-100 25.400 1 UC205-100 UCFA206-101 26.988 1-1/16 UC206-101 UCFA206-102 28.575 1-1/8 UC206-102 UCFA206 30 UC206 144 117 18 14 31.0 12 13 58 80 72 40.2 38.1 15.9 M10 FA206 0.93 UCFA206-103 30.162 1-3/16 UC206-103 UCFA206-104 31.750 1-1/4 UC206-104 UCFA207-104 31.750 1-1/4 UC207-104 UCFA207-105 33.338 1-5/16 UC207-105 161 130 19 16 34.0 15 15 66 90 82 44.4 42.9 17.5 M12 FA207 1.28 UCFA207-106 34.925 1-3/8 UC207-106 UCFA207 35 UC207 UCFA207-107 36.512 1-7/16 UC207-107 UCFA208-107 36.512 1-7/16 UC208-107 UCFA208-108 38.100 1-1/2 UC208-108 175 144 21 16 36.0 15 15 71 100 87 51.2 49.2 19.0 M12 FA208 1.68 UCFA208-109 39.688 1-9/16 UC208-109 UCFA208 40 UC208 UCFA209-110 41.275 1-5/8 UC209-110 UCFA209-111 42.862 1-11/16 UC209-111 181 148 22 18 38.0 15 15 72 108 90 52.2 49.2 19.0 M12 FA209 2.10 UCFA209-112 44.450 1-3/4 UC209-112 UCFA209 45 UC209 UCFA210-113 46.038 1-13/16 UC210-113 UCFA210-114 47.625 1-7/8 UC210-114 UCFA210-115 49.212 1-15/16 UC210-115 190 157 22 18 40.0 15 15 76 115 94 54.6 51.6 19.0 M12 FA210 2.20 UCFA210 50 UC210 UCFA210-200 50.800 2 UC210-200 UCFA211-200 50.800 2 UC211-200 UCFA211-201 52.388 2-1/16 UC211-201 219 184 25 20 43 16 17 86 130 104 58.4 55.6 22.2 M14 FA211 3.40 UCFA211-202 53.975 2-1/8 UC211-202 UCFA211 55 UC211 UCFA211-203 55.562 2-3/16 UC211-203 192
BALL BRG UNITS Special Flanged Units UCFH 200 Offset Flange Cartridges UCFH 200 with Set Screws Shaft Diameter: 12 50.800mm Part No. Example: For Bearing UC 206 Order Complete Unit UCFH 206 Unit Shaft Bearing Dimensions in mm Bolt Hsng Appr No. Diameter No. A H E J I G L C S B F Z Bi N Size No Wt. mm inch mm UCFH201 12 UC201 110 42 32 27 15 13 25.5 52 10 62 52 33.3 31.0 12.7 M8 FH204 0.60 UCFH201-008 12.700 1/2 UC201-008 UCFH202-009 14.288 9/16 UC202-009 UCFH202 15 UC202 110 42 32 27 15 13 25.5 52 10 62 52 33.3 31.0 12.7 M8 FH204 0.58 UCFH202-010 15.875 5/8 UC202-010 UCFH203 17 UC203 110 42 32 27 15 13 25.5 52 10 62 52 33.3 31.0 12.7 M8 FH204 0.57 UCFH203-011 17.462 11/16 UC203-011 UCFH204-012 19.050 3/4 UC204-012 110 42 32 27 15 13 25.5 52 10 62 52 33.3 31.0 12.7 M8 FH204 0.55 UCFH204 20 UC204 UCFH205-013 20.638 13/16 UC205-013 UCFH205-014 22.225 7/8 UC205-014 UCFH205-015 23.812 15/16 UC205-015 116 45 34 27 16 13 27.0 52 10 68 56 35.7 34.0 14.3 M8 FH205 0.68 UCFH205 25 UC205 UCFH205-100 25.400 1 UC205-100 UCFH206-101 26.988 1-1/16 UC206-101 UCFH206-102 28.575 1-1/8 UC206-102 UCFH206 30 UC206 130 50 40 29 18 13 31.0 55 10 78 65 40.2 38.1 15.9 M8 FH206 0.92 UCFH206-103 30.162 1-3/16 UC206-103 UCFH206-104 31.750 1-1/4 UC206-104 UCFH207-104 31.750 1-1/4 UC207-104 UCFH207-105 33.338 1-5/16 UC207-105 144 55 46 32 19 15 34.0 62 10 90 70 44.4 42.9 17.5 M8 FH207 1.32 UCFH207-106 34.925 1-3/8 UC207-106 UCFH207 35 UC207 UCFH207-107 36.512 1-7/16 UC207-107 UCFH208-107 36.512 1-7/16 UC208-107 UCFH208-108 38.100 1-1/2 UC208-108 164 60 50 41 21 16 36.0 72 12 100 78 51.2 49.2 19.0 M10 FH208 1.80 UCFH208-109 39.688 1-9/16 UC208-109 UCFH208 40 UC208 UCFH209-110 41.275 1-5/8 UC209-110 UCFH209-111 42.862 1-11/16 UC209-111 UCFH209-112 44.450 1-3/4 UC209-112 174 65 54 43 22 18 38 76 12 106 80 52.2 49.2 19.0 M10 FH209 2.10 UCFH209 45 UC209 UCFH210-113 46.038 1-13/16 UC210-113 UCFH210-114 47.625 1-7/8 UC210-114 UCFH210-115 49.212 1-15/16 UC210-115 184 68 58 46 22 18 40 82 12 112 86 54.6 51.6 19.0 M10 FH210 2.30 UCFH210 50 UC210 UCFH210-200 50.800 2 UC210-200 193
BALL BRG UNITS Take Up: Cast Iron UCT 200 Take Up Units: UCT 200 with Set Screws Shaft Diameter: 12 85 mm Part No. Example: For Bearing UC 208 Order Complete Unit UCT 208 Unit Shaft Bearing Dimensions in mm Hsg Appr No. Diameter No O G P Q S B K E A W J L H Bi N No Wt. mm inch Kg UCT201 12 UC201 16 10 51 32 19 51 12 76 89 94 32 21 61 31.0 12.7 T204 1.30 UCT201-008 12.700 1/2 UC201-008 UCT202-009 14.288 9/16 UC202-009 UCT202 15 UC202 16 10 51 32 19 51 12 76 89 94 32 21 61 31.0 12.7 T204 1.26 UCT202-010 15.875 5/8 UC202-010 UCT203 17 UC203 16 10 51 32 19 51 12 76 89 94 32 21 61 31.0 12.7 T204 1.23 UCT203-011 17.462 11/16 UC203-011 UCT204-012 19.050 3/4 UC204-012 16 10 51 32 19 51 12 76 89 94 32 21 61 31.0 12.7 T204 1.19 UCT204 20 UC204 UCT205-013 20.638 13/16 UC205-013 UCT205-014 22.225 7/8 UC205-014 UCT205-015 23.812 15/16 UC205-015 16 10 51 32 19 51 12 76 89 97 32 24 62 34.0 14.3 T205 1.46 UCT205 25 UC205 UCT205-100 25.400 1 UC205-100 UCT206-101 26.988 1-1/16 UC206-101 UCT206-102 28.575 1-1/8 UC206-102 UCT206 30 UC206 16 10 56 37 22 57 12 89 102 113 37 28 70 38.1 15.9 T206 2.30 UCT206-103 30.162 1-3/16 UC206-103 UCT206-104 31.750 1-1/4 UC206-104 UCT207-104 31.750 1-1/4 UC207-104 UCT207-105 33.338 1-5/16 UC207-105 16 13 64 37 22 64 12 89 102 129 37 30 78 42.9 17.5 T207 3.60 UCT207-106 34.925 1-3/8 UC207-106 UCT207 35 UC207 UCT207-107 36.512 1-7/16 UC207-107 UCT208-107 36.512 1-7/16 UC208-107 UCT208-108 38.100 1-1/2 UC208-108 19 16 83 49 29 83 16 102 114 144 49 33 88 49.2 19.0 T208 2.40 UCT208-109 39.688 1-9/16 UC208-109 UCT208 40 UC208 UCT209-110 41.275 1-5/8 UC209-110 UCT209-111 42.862 1-11/16 UC209-111 19 16 83 49 29 83 16 102 117 144 49 35 87 49.2 19.0 T209 2.40 UCT209-112 44.450 1-3/4 UC209-112 UCT209 45 UC209 UCT210-113 46.038 1-13/16 UC210-113 UCT210-114 47.625 1-7/8 UC210-114 UCT210-115 49.212 1-15/16 UC210-115 19 16 83 49 29 86 16 102 117 149 49 37 90 51.6 19.0 T210 2.50 UCT210 50 UC210 UCT210-200 50.800 2 UC210-200 UCT211-200 50.800 2 UC211-200 UCT211-201 52.388 2-1/16 UC211-201 25 19 102 64 35 95 22 130 146 171 64 38 106 55.6 22.2 T211 3.30 UCT211-202 53.975 2-1/8 UC211-202 UCT211 55 UC211 UCT211-203 55.562 2-3/16 UC211-203 UCT212-204 57.150 2-1/4 UC212-204 UCT212-205 58.738 2-5/16 UC212-205 32 19 102 64 35 102 22 130 146 194 64 42 119 65.1 25.4 T212 5.00 UCT212 60 UC212 UCT212-206 60.325 2-3/8 UC212-206 UCT213-207 61.912 2-7/16 UC213-207 UCT213-208 63.500 2-1/2 UC213-208 32 21 111 70 41 121 26 151 167 224 70 44 137 65.1 25.4 T213 7.00 UCT213 65 UC213 UCT214-210 66.675 2-5/8 UC214-210 UCT214-211 68.262 2-11/16 UC214-211 32 21 111 70 41 121 26 151 167 224 70 46 137 74.6 30.2 T214 7.20 UCT214-212 69.850 2-3/4 UC214-212 UCT214 70 UC214 UCT215-213 71.438 2-13/16 UC215-213 UCT215-214 73.025 2-7/8 UC215-214 UCT215-215 74.612 2-15/16 UC215-215 32 21 111 70 41 121 26 151 167 232 70 48 140 77.8 33.3 T215 8.20 UCT215 75 UC215 UCT215-300 76.200 3 UC215-300 UCT216-302 79.375 3-1/8 UC216-302 UCT216 80 UC216 32 21 111 70 41 121 26 165 184 235 70 51 140 82.6 33.3 T216 8.90 UCT216-303 80.962 3-3/16 UC216-303 UCT217-304 82.550 3-1/4 UC217-304 38 29 124 73 48 157 30 173 198 260 73 54 162 85.7 34.1 T217 10.6 UCT217 85 UC217 194
BALL BRG UNITS Take Up: Cast Iron UELT 200 Take Up Units UELT 200 with Eccentric Locking Collar Shaft Diameter: 19.050-76.200 mm Part No. Example: For Bearing UEL 209 Order Complete Unit UELT 209 Unit Shaft Bearing Dimensions in mm Hsg Appr No. Diameter No. O G P Q S B K E A W J L H Bi N No Wt. mm inch Kg UELT204-012 19.050 3/4 UEL204-012 16 10 51 32 19 51 12 76 89 94 32 21 61 43.7 17.1 T204 0.60 UELT204 20 UEL204 UELT205-013 20.638 13/16 UEL205-013 UELT205-014 22.225 7/8 UEL205-014 UELT205-015 23.812 15/16 UEL205-015 16 10 51 32 19 51 12 76 89 97 32 24 62 44.4 17.5 T205 0.69 UELT205 25 UEL205 UELT205-100 25.400 1 UEL205-100 UELT206-101 26.988 1-1/16 UEL206-101 UELT206-102 28.575 1-1/8 UEL206-102 UELT206 30 UEL206 16 10 56 37 22 57 12 89 102 113 37 28 70 48.4 18.3 T206 1.11 UELT206-103 30.162 1-3/16 UEL206-103 UELT206-104 31.750 1-1/4 UEL206-104 UELT207-104 31.750 1-1/4 UEL207-104 UELT207-105 33.338 1-5/16 UEL207-105 UELT207-106 34.925 1-3/8 UEL207-106 16 13 64 37 22 64 12 89 102 129 37 30 78 51.1 18.8 T207 1.77 UELT207 35 UEL207 UELT207-107 36.512 1-7/16 UEL207-107 UELT208-107 36.512 1-7/16 UEL208-107 UELT208-108 38.100 1-1/2 UEL208-108 19 16 83 49 29 83 16 102 114 144 49 33 88 56.3 21.4 T208 2.50 UELT208-109 39.688 1-9/16 UEL208-109 UELT208 40 UEL208 UELT209-110 41.275 1-5/8 UEL209-110 UELT209-111 42.862 1-11/16 UEL209-111 19 16 83 49 29 83 16 102 117 144 49 35 87 56.3 21.4 T209 2.60 UELT209-112 44.450 1-3/4 UEL209-112 UELT209 45 UEL209 UELT210-113 46.038 1-13/16 UEL210-113 UELT210-114 47.625 1-7/8 UEL210-114 UELT210-115 49.212 1-15/16 UEL210-115 19 16 83 49 29 86 16 102 117 149 49 37 90 62.7 24.6 T210 2.70 UELT210 50 UEL210 UELT210-200 50.800 2 UEL210-200 UELT211-200 50.800 2 UEL211-200 UELT211-201 52.388 2-1/16 UEL211-201 UELT211-202 53.975 2-1/8 UEL211-202 25 19 102 64 35 95 22 130 146 171 64 38 106 71.4 27.8 T211 3.70 UELT211 55 UEL211 UELT211-203 55.562 2-3/16 UEL211-203 UELT212-204 57.150 2-1/4 UEL212-204 UELT212-205 58.738 2-5/16 UEL212-205 32 19 102 64 35 102 22 130 146 194 64 42 119 77.8 31.0 T212 5.30 UELT212 60 UEL212 UELT212-206 60.325 2-3/8 UEL212-206 UELT213-207 61.912 2-7/16 UEL213-207 UELT213-208 63.500 2-1/2 UEL213-208 32 21 111 70 41 121 26 151 167 224 70 44 137 85.7 34.1 T213 7.50 UELT213 65 UEL213 UELT214-210 66.675 2-5/8 UEL214-210 UELT214-211 68.262 2-11/16 UEL214-211 32 21 111 70 41 121 26 151 167 224 70 46 137 85.7 34.1 T214 7.70 UELT214-212 69.850 2-3/4 UEL214-212 UELT214 70 UEL214 UELT215-213 71.438 2-13/16 UEL215-213 UELT215-214 73.025 2-7/8 UEL215-214 UELT215-215 74.612 2-15/16 UEL215-215 32 21 111 70 41 121 26 151 167 232 70 48 140 92.1 37.3 T215 8.60 UELT215 75 UEL215 UELT215-300 76.200 3 UEL215-300 195
BALL BRG UNITS Take Up Units UKT 200 + H with Adapter Shaft Diameter: 19.050 76.200 mm Take Up: Cast Iron UKT 200 Part No. Example: For Bearing UK 208 Order Complete Unit UKT 208 + H2305 (to fit 35mm shaft) Unit Shaft Bearing Dimensions in mm Hsg Appr No. Diameter No O G P Q S B K E A W J l H L No Wt. mm inch Kg UKT205+HE2305 19.050 3/4 UK205 16 10 51 32 19 51 12 76 89 97 32 24 62 35 T205 0.69 UKT205+H 2305 20 UKT206+HS2306 22.225 7/8 UKT206+HA2306 23.812 15/16 UK206 16 10 56 37 22 57 12 89 102 113 37 28 70 38 T206 1.15 UKT206+H 2306 25 UKT206+HE2306 25.400 1 UKT207+HS2307 28.575 1-1/8 UKT207+H 2307 30 UK207 16 13 64 37 22 64 12 89 102 129 37 30 78 43 T207 1.69 UKT207+HA2307 30.162 1-3/16 UKT208+HE2308 31.750 1-1/4 UKT208+HS2308 34.925 1-3/8 UK208 19 16 83 49 29 83 16 102 114 144 49 33 88 46 T208 2.30 UKT208+H 2308 35 UKT209+HA2309 36.512 1-7/16 UKT209+HE2309 38.100 1-1/2 UK209 19 16 83 49 29 83 16 102 117 144 49 35 87 50 T209 2.50 UKT209+H 2309 40 UKT210+HS2310 41.275 1-5/8 UKT210+HA2310 42.862 1-11/16 UK210 19 16 83 49 29 86 16 102 117 149 49 37 90 55 T210 2.80 UKT210+HE2310 44.450 1-3/4 UKT210+H 2310 45 UKT211+HS2311 47.625 1-7/8 UKT211+HA2311 49.212 1-15/16 UK211 25 19 102 64 35 95 22 130 146 171 64 38 106 59 T211 3.50 UKT211+H 2311 50 UKT211+HE2311 50.800 2 UKT212+HS2312 53.975 2-1/8 UK212 32 19 102 64 35 102 22 130 146 194 64 42 119 62 T212 4.90 UKT212+H 2312 55 UKT213+HA2313 55.562 2-3/16 UKT213+HE2313 57.150 2-1/4 UK213 32 21 111 70 41 121 26 151 167 224 70 44 137 65 T213 7.10 UKT213+H 2313 60 UKT213+HS2313 60.325 2-3/8 UKT215+HA2315 61.912 2-7/16 UKT215+HE2315 63.500 2-1/2 UK215 32 21 111 70 41 121 26 151 167 232 70 48 140 73 T215 8.60 UKT215+H 2315 65 UKT216+HA2316 68.262 2-11/16 UKT216+HE2316 69.850 2-3/4 UK216 32 21 111 70 41 121 26 165 184 235 70 51 140 78 T216 9.30 UKT216+H 2316 70 UKT217+HA2317 74.612 2-15/16 UKT217+H 2317 75 UK217 38 29 124 73 48 157 30 173 198 260 73 54 162 82 T217 10.80 UKT217+HE2317 76.200 3 Note: Pressed Steel covers are also available. Please contact any Branch near you for details. 196
BALL BRG UNITS Take Up: Pressed Metal MSTU The MSTU Pressed Steel Take-Up Unit is a light duty, economical, easy to mount unit for adjusting shafts and belt tightening devices on many types of conveyors and elevators. It is adaptable to either guide type or bolt type methods of mounting. The new design of bearing seat incorporated in the base plate is made to a looser than normal fit to ensure bearing self-alignment without loosening the flangette bolts. This assures self-alignment of the bearings, if the two take-up units are not pulled up evenly. The MSTU Take-Up Unit incorporates an AEL/AS series wide inner ring bearing. A complete MSTU Take-Up Unit consists of MSTU base plate, MST flangette, and AEL/AS bearing. Stamp Shaft Bearing Flng t Dimensions in mm Bolt Size Size Number No A B C D E F H J K L Size LR** LS inch mm AEL AS mm kgf/lbf RPM 52MSTU 25 AEL205 AS205 52MSTU 7/8 AEL205-014 AS205-014 52MST 104.8 203.2 8.7 76.2 114.3 71.4 2.1 33.3 10.3 38.1 7.9 363.2 6000 52MSTU 1 AEL205-100 AS205-100 52MST 62MSTU 30 AEL206 AS206 62MSTU 1-1/8 AEL206-102 AS206-102 62MST 114.3 203.2 8.7 90.5 152.4 81.0 2.6 37.3 11.1 44.5 9.5 499.4 4800 62MSTU 1-1/4 AEL206-104 AS206-104 62MST Recommended shaft tolerance -: Up to 50mm(2") dia. inclusive Nominal to -.0127mm(.0005") Over 50mm(2") dia. Nominal to -.0254mm(.0010") These tolerances correspond to those of precision ground shafting. Commercial grade bright mild steel shafting Part No. Example: For Bearing AEL205-100 Order Stamping 52MSTU Note: AEL = Eccentric Collar Locking AS = Set Screw Locking 197
BALL BRG UNITS Hanger Unit: Cast Iron UCHB 200 Hanger Cartridges UCHB 200 with Set Screws Shaft Diameter: 12 60 mm Part No. Example: For Bearing UC 206 Order Complete Unit UCHB 206 Unit Shaft Bearing Dimensions in mm Hsng Appr No Diameter No A W H J S G Bi N No Wt. mm inch Kg UCHB201 12 UC201 64 96 64 40 PF 3/4 24 31.0 12.7 HB204 0.64 UCHB201-008 12.700 1/2 UC201-008 UCHB202-009 14.288 9/16 UC202-009 UCHB202 15 UC202 64 96 64 40 PF 3/4 24 31.0 12.7 HB204 0.63 UCHB202-010 15.875 5/8 UC202-010 UCHB203 17 UC203 64 96 64 40 PF 3/4 24 31.0 12.7 HB204 0.62 UCHB203-011 17.462 11/16 UC203-011 UCHB204-012 19.050 3/4 UC204-012 64 96 64 40 PF 3/4 24 31.0 12.7 HB204 0.60 UCHB204 20 UC204 UCHB205-013 20.638 13/16 UC205-013 UCHB205-014 22.225 7/8 UC205-014 UCHB205-015 23.812 15/16 UC205-015 70 99 64 40 PF 3/4 24 34.0 14.3 HB205 0.66 UCHB205 25 UC205 UCHB205-100 25.400 1 UC205-100 UCHB206-101 26.988 1-1/16 UC206-101 UCHB206-102 28.575 1-1/8 UC206-102 UCHB206 30 UC206 80 104 64 40 PF 3/4 24 38.1 15.9 HB206 0.89 UCHB206-103 30.162 1-3/16 UC206-103 UCHB206-104 31.750 1-1/4 UC206-104 UCHB207-104 31.750 1-1/4 UC207-104 UCHB207-105 33.338 1-5/16 UC207-105 UCHB207-106 34.925 1-3/8 UC207-106 92 116 70 40 PF 3/4 24 42.9 17.5 HB207 1.19 UCHB207 35 UC207 UCHB207-107 36.512 1-7/16 UC207-107 UCHB208-107 36.512 1-7/16 UC208-107 UCHB208-108 38.100 1-1/2 UC208-108 96 121 73 40 PF 3/4 24 49.2 19.0 HB208 1.34 UCHB208-109 39.688 1-9/16 UC208-109 UCHB208 40 UC208 UCHB209-110 41.275 1-5/8 UC209-110 UCHB209-111 42.862 1-11/16 UC209-111 108 136 82 48 PF 1 28 49.2 19.0 HB209 1.78 UCHB209-112 44.450 1-3/4 UC209-112 UCHB209 45 UC209 UCHB210-113 46.038 1-13/16 UC210-113 UCHB210-114 47.625 1-7/8 UC210-114 UCHB210-115 49.212 1-15/16 UC210-115 114 140 83 48 PF 1 28 51.6 19.0 HB210 1.92 UCHB210 50 UC210 UCHB210-200 50.800 2 UC210-200 UCHB211-200 50.800 2 UC211-200 UCHB211-201 52.388 2-1/16 UC211-201 UCHB211-202 53.975 2-1/8 UC211-202 126 150 87 60 PF 1-1/4 27 55.6 22.2 HB211 2.60 UCHB211 55 UC211 UCHB211-203 55.562 2-3/16 UC211-203 UCHB212-204 57.150 2-1/4 UC212-204 UCHB212-205 58.738 2-5/16 UC212-205 142 173 102 60 PF 1-1/4 35 65.1 25.4 HB212 3.80 UCHB212 60 UC212 198
BALL BRG UNITS Cartridge Type: Cast Iron UCC2 Cylindrical Cartridges UCC 200 with Set Screws Shaft Diameter: 12-65 mm Part No. Example: For Bearing UC 206 Order Complete Unit UCC 206 Unit Shaft Bearing Dimensions in mm Hsng No Diameter No. A L r-mm Bi N No Wt mm inch kg UCC201 12 UC201 72 20 1.0 31.0 12.7 C204 0.53 UCC201-008 12.700 1/2 UC201-008 UCC202-009 14.288 9/16 UC202-009 UCC202 15 UC202 72 20 1.0 31.0 12.7 C204 0.51 UCC202-010 15.875 5/8 UC202-010 UCC203 17 UC203 72 20 1.0 31.0 12.7 C204 0.50 UCC203-011 17.462 11/16 UC203-011 UCC204-012 19.050 3/4 UC204-012 72 20 1.0 31.0 12.7 C204 0.48 UCC204 20 UC204 UCC205-013 20.638 13/16 UC205-013 UCC205-014 22.225 7/8 UC205-014 UCC205-015 23.812 15/16 UC205-015 80 22 1.0 34.0 14.3 C205 0.65 UCC205 25 UC205 UCC205-100 25.400 1 UC205-100 UCC206-101 26.988 1-1/16 UC206-101 UCC206-102 28.575 1-1/8 UC206-102 UCC206 30 UC206 85 27 1.0 38.1 15.9 C206 0.79 UCC206-103 30.162 1-3/16 UC206-103 UCC206-104 31.750 1-1/4 UC206-104 UCC207-104 31.750 1-1/4 UC207-104 UCC207-105 33.338 1-5/16 UC207-105 90 28 1.0 42.9 17.5 C207 0.90 UCC207-106 34.925 1-3/8 UC207-106 UCC207 35 UC207 UCC207-107 36.512 1-7/16 UC207-107 UCC208-107 36.512 1-7/16 UC208-107 UCC208-108 38.100 1-1/2 UC208-108 100 30 1.0 49.2 19.0 C208 1.24 UCC208-109 39.688 1-9/16 UC208-109 UCC208 40 UC208 UCC209-110 41.275 1-5/8 UC209-110 UCC209-111 42.862 1-11/16 UC209-111 110 31 1.0 49.2 19.0 C209 1.55 UCC209-112 44.450 1-3/4 UC209-112 UCC209 45 UC209 UCC210-113 46.038 1-13/16 UC210-113 UCC210-114 47.625 1-7/8 UC210-114 UCC210-115 49.212 1-15/16 UC210-115 120 33 1.0 51.6 19.0 C210 1.90 UCC210 50 UC210 UCC210-200 50.800 2 UC210-200 UCC211-200 50.800 2 UC211-200 UCC211-201 52.388 2-1/16 UC211-201 UCC211-202 53.975 2-1/8 UC211-202 125 35 1.0 55.6 22.2 C211 2.10 UCC211 55 UC211 UCC211-203 55.562 2-3/16 UC211-203 UCC212-204 57.150 2-1/4 UC212-204 UCC212-205 58.738 2-5/16 UC212-205 130 38 1.0 65.1 25.4 C212 2.50 UCC212 60 UC212 UCC212-206 60.325 2-3/8 UC212-206 UCC213-207 61.912 2-7/16 UC213-207 UCC213-208 63.500 2-1/2 UC213-208 140 40 1.5 65.1 25.4 C213 2.90 UCC213 65 UC213 Note: Recommended grease nipple size; UCC201~213... 1/4-28UNF. 199
BALL BRG UNITS Cartridge Type: Cast Iron UKC2 Cylindrical Cartridges UKC 200 + H with Adapter Shaft Diameter: 19.050 60.325 mm Part No. Example: For Bearing UK 206 Order Housing C206 Complete Unit UKC 206 + H2306 (for 25mm shaft) Unit Shaft Diameter Bearing Dimensions in mm Housing Wt No. mm inch No. a l r-mm L No kg UKC205+HE2305 19.050 3/4 UK205 80 22 1.0 35 C205 0.69 UKC205+H 2305 20 UKC206+HS2306 22.225 7/8 UKC206+HA2306 23.812 15/16 UK206 85 27 1.0 38 C206 0.89 UKC206+H 2306 25 UKC206+HE2306 25.400 1 UKC207+HS2307 28.575 1-1/8 UKC207+H 2307 30 UK207 90 28 1.0 43 C207 0.94 UKC207+HA2307 30.162 1-3/16 UKC208+HE2308 31.750 1-1/4 UKC208+HS2308 34.925 1-3/8 UK208 100 30 1.0 46 C208 1.25 UKC208+H 2308 35 UKC209+HA2309 36.512 1-7/16 UKC209+HE2309 38.100 1-1/2 UK209 110 31 1.0 50 C209 1.66 UKC209+H 2309 40 UKC210+HS2310 41.275 1-5/8 UKC210+HA2310 42.862 1-11/16 UK210 120 33 1.0 55 C210 2.10 UKC210+HE2310 44.450 1-3/4 UKC210+H 2310 45 UKC211+HS2311 47.625 1-7/8 UKC211+HA2311 49.212 1-15/16 UK211 125 35 1.0 59 C211 2.20 UKC211+H 2311 50 UKC211+HE2311 50.800 2 UKC212+HS2312 53.975 2-1/8 UK212 130 38 1.0 62 C212 2.40 UKC212+H 2312 55 UKC213+HA2313 55.562 2-3/16 UKC213+HE2313 57.150 2-1/4 UK213 140 40 1.0 65 C213 3.00 UKC213+H 2313 60 UKC213+HS2313 60.325 2-3/8 1.5 Note: Recommended grease nipple size; UKC205~213... 1/4-28UNF. 200
BALL BRG UNITS Housed Bearing Inserts Selection Guide SELECTION GUIDE - HOUSED BEARING INSERTS Type Locking Method Bore Diameter Relubricating WidtH Outside Diameter Series Capability UC 2 Set Screw Cylindrical 2 Grease fitting Wide Spherical UC 3 Set Screw Cylindrical 3 Grease fitting Wide Spherical UC X Set Screw Cylindrical X Grease fitting Wide Spherical UEL 2 Eccentric Locking Collar Cylindrical 2 Grease fitting Wide Spherical UK 2 Adapter Sleeve Tapered 2 Grease fitting Wide Spherical UK 3 Adapter Sleeve Tapered 3 Grease fitting Wide Spherical UK X Adapter Sleeve Tapered X Grease fitting Wide Spherical AS 2 Set Screw Cylindrical 2 None Narrow Spherical AEL 2 Eccentric Locking Collar Cylindrical 2 None Narrow Spherical AELS 2 Eccentric Locking Collar Cylindrical 2 None Narrow Cylindrical Flat OD UCS 2 Set Screw Cylindrical 2 Grease fitting Wide Cylindrical Flat OD UC 200 UC X00 UC 300 AS 200 AELS 200 UEL 200 AEL 200 UCS 200 UK 200 UK X00 UK 300 201
BALL BRG UNITS UC 200 Set Screw Type Bore Diameter: 12 101.6 mm 1/2 4inch Inserts: Spherical O/D UC2 Part No. Example: Bearing to suit 25 mm shaft, order: UC 205 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Wt Number mm inch D B i B e N M G d s Dyn Stat kg C C o UC201 12.000 47 31 17 12.7 18.3 4.5 M6x0.75 1300 635 0.20 UC201-008 12.700 1/2 0.20 UC202-009 14.288 9/16 0.19 UC202 15.000 47 31 17 12.7 18.3 4.5 M6x0.75 1300 635 0.19 UC202-010 15.875 5/8 0.18 UC203 17.000 47 31 17 12.7 18.3 4.5 M6x0.75 1300 635 0.18 UC203-011 17.462 11/16 0.17 UC204-012 19.050 3/4 47 31 17 12.7 18.3 4.5 M6x0.75 1300 635 0.16 UC204 20.000 0.16 UC205-013 20.638 13/16 0.24 UC205-014 22.225 7/8 0.22 UC205-015 23.812 15/16 52 34 17 14.3 19.7 5.0 M6x0.75 1430 730 0.21 UC205 25.000 0.19 UC205-100 25.400 1 0.19 UC206-015 23.812 1-15/16 0.39 UC206-100 25.400 1 0.37 UC206-101 26.988 1-1/16 0.35 UC206-102 28.575 1-1/8 62 38.1 19 15.9 22.2 5.0 M6x0.75 1990 1050 0.33 UC206 30.000 0.31 UC206-103 30.162 1-3/16 0.31 UC206-104 31.750 1-1/4 0.29 UC207-103 30.162 1-3/16 0.56 UC207-104 31.750 1-1/4 0.53 UC207-105 33.338 1-5/16 0.50 UC207-106 34.925 1-3/8 72 42.9 20 17.5 25.4 6.0 M8x1.00 2620 1430 0.48 UC207 35.000 0.47 UC207-107 36.512 1-7/16 0.44 UC208-107 36.512 1-7/16 0.71 UC208-108 38.100 1-1/2 0.68 UC208-109 39.688 1-9/16 80 49.2 21 19.0 30.2 8.0 M8x1.00 2970 1650 0.64 UC208 40.000 0.63 UC209-108 38.100 1-1/2 0.87 UC209-109 39.688 1-9/16 0.83 UC209-110 41.275 1-5/8 0.79 UC209-111 42.862 1-11/16 85 49.2 22 19.0 30.2 8.0 M8x1.00 3200 1850 0.75 UC209-112 44.450 1-3/4 0.71 UC209 45.000 0.69 UC210-111 42.862 1-11/16 0.98 UC210-112 44.450 1-3/4 0.93 UC210-113 46.038 1-13/16 0.89 UC210-114 47.625 1-7/8 90 51.6 23 19.0 32.6 9.0 M10x1.25 3600 2100 0.84 UC210-115 49.212 1-15/16 0.79 UC210 50.000 0.77 UC210-200 50.800 2 0.74 UC211-115 49.212 1-15/16 1.25 UC211-200 50.800 2 1.19 UC211-201 52.388 2-1/16 1.14 UC211-202 53.975 2-1/8 100 55.6 24 22.2 33.4 9.0 M10x1.25 4450 2660 1.08 UC211 55.000 1.04 UC211-203 55.562 2-3/16 1.02 UC212-203 55.562 2-3/16 1.70 UC212-204 57.150 2-1/4 1.60 UC212-205 58.738 2-5/16 110 65.1 27 25.4 39.7 10.0 M10x1.25 5350 3300 1.53 UC212 60.000 1.47 UC212-206 60.325 2-3/8 1.46 202
BALL BRG UNITS UC 200 Inserts: Spherical O/D UCX Bearing Bore Diameter Dimensions in mm Basic Load Ratings Wt Number mm inch D B i B e N M G d s Dyn Stat kg C C o UC213-206 60.325 2-3/8 2.00 UC213-207 61.912 2-7/16 1.93 UC213-208 63.500 2-1/2 120 65.1 28 25.4 39.7 10.0 M10x1.25 5850 3650 1.85 UC213 65.000 1.77 UC214-207 61.912 2-7/16 2.50 UC214-208 63.500 2-1/2 2.40 UC214-210 66.675 2-5/8 2.20 UC214-211 68.262 2-11/16 125 74.6 29 30.2 44.4 12.0 M12x1.50 6350 4000 2.10 UC214-212 69.850 2-3/4 2.00 UC214 70.000 2.00 UC215-211 68.262 2-11/16 2.60 UC215-212 69.850 2-3/4 2.50 UC215-213 71.438 2-13/16 2.50 UC215-214 73.025 2-7/8 130 77.8 30 33.3 44.5 12.0 M12x1.50 6750 4400 2.40 UC215-215 74.612 2-15/16 2.30 UC215 75.000 2.30 UC215-300 76.200 3 2.20 UC216-215 74.612 2-15/16 3.10 UC216-300 76.200 3 3.00 UC216-302 79.375 3-1/8 140 82.6 32 33.3 49.3 12.0 M12x1.50 7400 4750 2.80 UC216 80.000 2.70 UC216-303 80.962 3-3/16 2.60 UC217-303 80.962 3-3/16 3.70 UC217-304 82.550 3-1/4 150 85.7 34 34.1 51.6 12.0 M12x1.50 8550 5600 3.50 UC217 85.000 3.30 UC218-307 87.312 3-7/16 4.50 UC218-308 88.900 3-1/2 160 96.0 36 39.7 56.3 12.0 M12x1.50 9800 6450 4.30 UC218 90.000 4.20 UC221-315 100.012 3-15/16 190 117.5 42 49.2 68.3 16.0 M16x1.50 13600 9500 7.90 UC221-400 101.600 4 7.70 UC X00 Set Screw Type Bore Diameter: 25 100 mm Part No. Example: Bearing to suit 50 mm shaft, order: UC X10 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Wt Number mm inch D B i B e N M G d s Dyn Stat kg C C o UCX05 25 0.9843 62 38.1 19 15.9 22.2 5 M6x0.75 1990 1050 0.38 UCX06 30 1.1811 72 42.9 20 17.5 25.4 6 M8x1.00 2620 1430 0.56 UCX07 35 1.3780 80 49.2 21 19.0 30.2 8 M8x1.00 2970 1650 0.75 UCX08 40 1.5748 85 49.2 22 19.0 30.2 8 M8x1.00 3200 1850 0.82 UCX09 45 1.7717 90 51.6 23 19.0 32.6 9 M10x1.25 3600 2100 0.92 UCX10 50 1.9685 100 55.6 24 22.2 33.4 9 M10x1.25 4450 2660 1.22 UCX11 55 2.1654 110 65.1 27 25.4 39.7 10 M10x1.25 5350 3300 1.70 UCX12 60 2.3622 120 65.1 28 25.4 39.7 10 M10x1.25 5850 3650 2.00 UCX13 65 2.5591 125 74.6 29 30.2 44.4 12 M12x1.50 6350 4000 2.30 UCX14 70 2.7559 130 77.8 30 33.3 44.5 12 M12x1.50 6750 4400 2.50 UCX15 75 2.9528 140 82.6 32 33.3 49.3 12 M12x1.50 7400 4750 3.10 UCX16 80 3.1496 150 85.7 34 34.1 51.6 12 M12x1.50 8550 5600 3.70 UCX17 85 3.3465 160 96.0 36 39.7 56.3 12 M12x1.50 9800 6450 4.70 UCX18 90 3.5433 170 104.0 38 42.9 61.1 14 M14x1.50 11100 7400 5.70 UCX20 100 3.9370 190 117.5 42 49.2 68.3 16 M16x1.50 13600 9500 7.90 203
BALL BRG UNITS Inserts: Spherical O/D UC3 UC 300 Set Screw Type Bore Diameter: 20.638 140 mm 13/16 4inch Part No. Example: Bearing to suit 35 mm shaft, order: UC 307 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Wt Number mm inch D B i B e N M G d s Dyn Stat kg C C o UC305-013 20.638 13/16 0.42 UC305-014 22.225 7/8 0.40 UC305-015 23.812 15/16 62 38 22 15 23 6 M6x0.75 2100 1080 0.38 UC305 25.000 0.37 UC305-100 25.400 1 0.36 UC306-101 26.988 1-1/16 0.58 UC306-102 28.575 1-1/8 0.56 UC306 30.000 72 43 24 17 26 6 M6x0.75 2720 1440 0.54 UC306-103 30.162 1-3/16 0.53 UC306-104 31.750 1-1/4 0.51 UC307-104 31.750 1-1/4 0.77 UC307-105 33.338 1-5/16 0.74 UC307-106 34.925 1-3/8 80 48 26 19 29 8 M8x1.00 3400 1840 0.71 UC307 35.000 0.71 UC307-107 36.512 1-7/16 0.68 UC308-107 36.512 1-7/16 1.04 UC308-108 38.100 1-1/2 1.00 UC308-109 39.688 1-9/16 90 52 28 19 33 10 M10x1.25 4150 2300 0.97 UC308 40.000 0.96 UC309-110 41.275 1-5/8 1.39 UC309-111 42.862 1-11/16 100 57 30 22 35 10 M10x1.25 5400 3100 1.35 UC309-112 44.450 1-3/4 1.30 UC309 45.000 1.28 UC310-113 46.038 1-13/16 1.79 UC310-114 47.625 1-7/8 1.73 UC310-115 49.212 1-15/16 110 61 32 22 39 12 M12x1.50 6300 3650 1.68 UC310 50.000 1.65 UC310-200 50.800 2 1.62 UC311-200 50.800 2 2.20 UC311-201 52.388 2-1/16 2.20 UC311-202 53.975 2-1/8 120 66 34 25 41 12 M12x1.50 7300 4300 2.20 UC311 55.000 2.10 UC311-203 55.562 2-3/16 2.00 UC312-204 57.150 2-1/4 2.70 UC312-205 58.738 2-5/16 2.70 UC312 60.000 130 71 36 26 45 12 M12x1.50 8350 5000 2.60 UC312-206 60.325 2-3/8 2.60 UC313-207 61.912 2-7/16 3.30 UC313-208 63.500 2-1/2 140 75 38 30 45 12 M12x1.50 9450 5750 3.20 UC313 65.000 3.20 UC314-210 66.675 2-5/8 4.00 UC314-211 68.262 2-11/16 3.90 UC314-212 69.850 2-3/4 150 78 40 33 45 12 M12x1.50 10600 6550 3.80 UC314 70.000 3.80 UC315-213 71.438 2-13/16 4.80 UC315-214 73.025 2-7/8 4.70 UC315-215 74.612 2-15/16 160 82 42 32 50 14 M14x1.50 11600 7400 4.50 UC315 75.000 4.50 UC315-300 76.200 3 4.40 UC316-302 79.375 3-1/8 5.40 UC316 80.000 170 86 44 34 52 14 M14x1.50 12500 8250 5.30 UC316-303 80.962 3-3/16 5.20 204
BALL BRG UNITS Inserts: Spherical O/D AS2 UC 300 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Wt Number mm inch D B i B e N M G d s Dyn Stat kg C C o UC317-304 82.550 3-1/4 180 96 46 40 56 16 M16x1.50 13500 9200 6.70 UC317 85.000 6.40 UC318-307 87.312 3-7/16 7.60 UC318-308 88.900 3-1/2 190 96 48 40 56 16 M16x1.50 14500 10200 7.40 UC318 90.000 7.30 UC319 95.000 200 103 50 41 62 16 M16x1.50 15600 11300 8.50 UC319-312 95.250 3-3/4 8.50 UC320 100.000 10.70 UC320-315 100.012 3-15/16 215 108 54 42 66 18 M18x1.50 17700 13500 10.70 UC320-400 101.600 4 10.50 UC321 105.000 225 112 56 44 68 18 M18x1.50 18700 14700 12.00 UC322 110.000 240 117 60 46 71 18 M18x1.50 20900 17200 14.70 UC324 120.000 260 126 64 51 75 18 M18x1.50 21100 17400 18.90 UC326 130.000 280 135 68 54 81 20 M20x1.50 23400 20200 23.00 UC328 140.000 300 145 73 59 86 20 M20x1.50 25800 23200 28.00 AS 200 Set Screw Type Bore Diameter: 12 36.512 mm Part No. Example: Bearing to suit 25 mm shaft, order: AS 205 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Wt Number mm inch D B i B e N M G d s Dyn Stat kg C C o AS201 12 40 22.0 12 6.0 16.0 4.0 M5x0.80 975 460 0.09 AS201-008 12.700 1/2 0.09 AS202-009 14.288 9/16 0.08 AS202 15 40 22.0 12 6.0 16.0 4.0 M5x0.80 975 460 0.08 AS202-010 15.875 5/8 0.08 AS203 17 40 22.0 12 6.0 16.0 4.0 M5x0.80 975 460 0.07 AS203-011 17.462 11/16 0.07 AS204-012 19.050 3/4 47 24.7 14 7.0 17.7 4.5 M5x0.80 1300 635 0.12 AS204 20 0.11 AS205-013 20.638 13/16 0.18 AS205-014 22.225 7/8 0.17 AS205-015 23.812 15/16 52 27.0 15 7.5 19.5 5.0 M6x0.75 1430 730 0.16 AS205 25 0.15 AS205-100 25.400 1 0.14 AS206-101 26.988 1-1/16 0.26 AS206-102 28.575 1-1/8 0.25 AS206 30 62 30.3 16 8.0 22.3 5.0 M6x0.75 1990 1050 0.23 AS206-103 30.162 1-3/16 0.23 AS206-104 31.750 1-1/4 0.21 AS207-104 31.750 1-1/4 0.39 AS207-105 33.338 1-5/16 0.37 AS207-106 34.925 1-3/8 72 32.9 17 8.5 24.4 6.0 M8x1.00 2620 1430 0.35 AS207 35 0.34 AS207-107 36.512 1-7/16 0.32 205
BALL BRG UNITS Inserts: Spherical O/D UEL2 UEL 200 Eccentric Locking Collar Type Bore Diameter: 12 76.200 mm Part No. Example: Bearing to suit 40 mm shaft, order: UEL 208 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Eccentric Wt Number mm inch D L B i B e N G d s Dyn Stat Collar kg C C o No. UEL201 12 40 37.3 27.8 13 13.9 5 M6x0.75 975 460 EC201 0.16 UEL201-008 12.700 1/2 EC201-08 0.16 UEL202-009 14.288 9/16 EC202-09 0.15 UEL202 15 40 37.3 27.8 13 13.9 5 M6x0.75 975 460 EC202 0.14 UEL202-010 15.875 5/8 EC202-10 0.14 UEL203 17 40 37.3 27.8 13 13.9 5 M6x0.75 975 460 EC203 0.13 UEL203-011 17.462 11/16 EC203-11 0.12 UEL204-012 19.050 3/4 47 43.7 34.2 17 17.1 5 M6x0.75 1300 635 EC204-12 0.22 UEL204 20 EC204 0.21 UEL205-013 20.638 13/16 EC205-13 0.29 UEL205-014 22.225 7/8 EC205-14 0.27 UEL205-015 23.812 15/16 52 44.4 34.9 17 17.5 5 M6x0.75 1430 730 EC205-15 0.25 UEL205 25 EC205 0.23 UEL205-100 25.400 1 EC205-16 0.23 UEL206-101 26.988 1-1/16 EC206-17 0.43 UEL206-102 28.575 1-1/8 EC206-18 0.40 UEL206 30 62 48.4 36.5 19 18.3 6 M8x1.00 1990 1050 EC206 0.37 UEL206-103 30.162 1-3/16 EC206-19 0.37 UEL206-104 31.750 1-1/4 EC206-20 0.34 UEL207-104 31.750 1-1/4 EC207-20 0.67 UEL207-105 33.338 1-5/16 EC207-21 0.63 UEL207-106 34.925 1-3/8 72 51.1 37.6 20 18.8 7 M10x1.25 2620 1430 EC207-22 0.60 UEL207 35 EC207 0.60 UEL207-107 36.512 1-7/16 EC207-23 0.56 UEL208-107 36.512 1-7/16 EC208-23 0.85 UEL208-108 38.100 1-1/2 EC208-24 0.81 UEL208-109 39.688 1-9/16 80 56.3 42.8 21 21.4 7 M10x1.25 2970 1650 EC208-25 0.77 UEL208 40 EC208 0.76 UEL209-110 41.275 1-5/8 EC209-26 0.90 UEL209-111 42.862 1-11/16 85 56.3 42.8 22 21.4 7 M10x1.25 3200 1850 EC209-27 0.86 UEL209-112 44.450 1-3/4 EC209-28 0.81 UEL209 45 EC209 0.79 UEL210-113 46.038 1-13/16 EC210-29 1.05 UEL210-114 47.625 1-7/8 EC210-30 1.00 UEL210-115 49.212 1-15/16 90 62.7 49.2 23 24.6 7 M10x1.25 3600 2100 EC210-31 0.94 UEL210 50 EC210 0.91 UEL210-200 50.800 2 EC210-32 0.88 UEL211-200 50.800 2 EC211-32 1.47 UEL211-201 52.388 2-1/16 EC211-33 1.40 UEL211-202 53.975 2-1/8 100 71.4 55.5 24 27.8 8 M12x1.50 4450 2660 EC211-34 1.32 UEL211 55 EC211 1.27 UEL211-203 55.562 2-3/16 EC211-35 1.25 UEL212-204 57.150 2-1/4 EC212-36 1.87 UEL212-205 58.738 2-5/16 EC212-37 1.78 UEL212 60 110 77.8 61.9 27 31.0 8 M12x1.50 5350 3300 EC212 1.71 UEL212-206 60.325 2-3/8 EC212-38 1.69 UEL212-207 61.912 2-7/16 EC212-39 2.50 UEL213-208 63.500 2-1/2 120 85.7 68.2 28 34.1 9 M12x1.50 5850 3650 EC213-40 2.40 UEL213 65 EC213 2.30 UEL214-210 66.675 2-5/8 EC214-42 2.70 UEL214-211 68.262 2-11/16 EC214-43 2.60 UEL214-212 69.850 2-3/4 125 85.7 68.2 29 34.1 8.5 M12x1.50 6350 4000 EC214-44 2.50 UEL214 70 EC214 2.50 UEL215-213 71.438 2-13/16 EC215-45 2.90 UEL215-214 73.025 2-7/8 EC215-46 2.80 UEL215-215 74.612 2-15/16 130 92.1 74.6 30 37.3 9 M12x1.50 6750 4400 EC215-47 2.70 UEL215 75 EC215 2.70 UEL215-300 76.200 3 EC215-48 2.60 206
BALL BRG UNITS Inserts: Spherical O/D AEL2 AEL 200 Eccentric Locking Collar Type Bore Diameter: 12 60.325 mm Part No. Example: Bearing to suit 35 mm shaft, order: AEL 207 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Eccentric Wt Number mm inch D L B i B e N G d s Dyn Stat Collar kg C C o No. AEL201 12 40 28.6 19.1 12 6.5 5 M6x0.75 975 460 EC201 0.13 AEL201-008 12.700 1/2 EC201-08 0.13 AEL202-009 14.288 9/16 EC202-09 0.12 AEL202 15 40 28.6 19.1 12 6.5 5 M6x0.75 975 460 EC202 0.11 AEL202-010 15.875 5/8 EC202-10 0.11 AEL203 17 40 28.6 19.1 12 6.5 5 M6x0.75 975 460 EC203 0.10 AEL203-011 17.462 11/16 EC203-11 0.10 AEL204-012 19.050 3/4 47 31 21.5 14 7.5 5 M6x0.75 1300 635 EC204-12 0.17 AEL204 20 EC204 0.16 AEL205-013 20.638 13/16 EC205-13 0.24 AEL205-014 22.225 7/8 EC205-14 0.22 AEL205-015 23.812 15/16 52 31 21.5 15 7.5 5 M6x0.75 1430 730 EC205-15 0.21 AEL205 25 EC205 0.20 AEL205-100 25.400 1 EC205-16 0.19 AEL206-101 26.988 1-1/16 EC206-17 0.34 AEL206-102 28.575 1-1/8 EC206-18 0.32 AEL206 30 62 35.7 23.8 16 9 6 M8x1.00 1990 1050 EC206 0.31 AEL206-103 30.162 1-3/16 EC206-19 0.30 AEL206-104 31.750 1-1/4 EC206-20 0.28 AEL207-104 31.750 1-1/4 EC207-20 0.54 AEL207-105 33.338 1-5/16 EC207-21 0.51 AEL207-106 34.925 1-3/8 72 38.9 25.4 17 9.5 7 M10x1.25 2620 1430 EC207-22 0.49 AEL207 35 EC207 0.49 AEL207-107 36.512 1-7/16 EC207-23 0.46 AEL208-107 36.512 1-7/16 EC208-23 0.69 AEL208-108 38.100 1-1/2 EC208-24 0.66 AEL208-109 39.688 1-9/16 80 43.7 30.2 18 11 7 M10x1.25 2970 1650 EC208-25 0.63 AEL208 40 EC208 0.62 AEL209-110 41.275 1-5/8 EC209-26 0.74 AEL209-111 42.862 1-11/16 85 43.7 30.2 19 11 7 M10x1.25 3200 1850 EC209-27 0.70 AEL209-112 44.450 1-3/4 EC209-28 0.67 AEL209 45 EC209 0.65 AEL210-113 46.038 1-13/16 EC210-29 0.85 AEL210-114 47.625 1-7/8 EC210-30 0.81 AEL210-115 49.212 1-15/16 90 43.7 30.2 20 11 7 M10x1.25 3600 2100 EC210-31 0.77 AEL210 50 EC210 0.75 AEL210-200 50.800 2 EC210-32 0.73 AEL211-200 50.800 2 EC211-32 1.08 AEL211-201 52.388 2-1/16 EC211-33 1.03 AEL211-202 53.975 2-1/8 100 48.4 32.5 21 12 8 M12x1.50 4450 2660 EC211-34 0.98 AEL211 55 EC211 0.94 AEL211-203 55.562 2-3/16 EC211-35 0.93 AEL212-204 57.150 2-1/4 EC212-36 1.28 AEL212-205 58.738 2-5/16 EC212-37 1.22 AEL212 60 110 53.1 37.2 22 13.5 8 M12x1.50 5350 3300 EC212 1.17 AEL212-206 60.325 2-3/8 EC212-38 1.15 207
BALL BRG UNITS Inserts: Spherical O/D UK2 UK 200 Tapered Bore With Adapters Shaft Diameter: 19.050 80.962 mm Part No. Example: Bearing/Sleeve to suit 50 mm shaft, order: UK 211 + H2311 Bearing Shaft Diameter Dimensions in mm Basic Load Ratings Wt Adapter Dimensions in mm Number mm inch d D B i B e Dyn Stat kg No. L Y W C C o UK205 19.050 3/4 25 52 23 17 1430 730 0.15 HE2305 35 8 38 20 H 2305 22.225 7/8 HS2306 23.812 15/16 HA2306 UK206 25 30 62 26 19 1990 1050 0.26 H 2306 38 8 45 25.400 1 HE2306 28.575 1-1/8 HS2307 UK207 30 35 72 27 20 2620 1430 0.36 H 2307 43 9 52 30.162 1-3/16 HA2307 31.750 1-1/4 HE2308 UK208 34.925 1-3/8 40 80 29 21 2970 1650 0.47 HS2308 46 10 58 35 H 2308 36.512 1-7/16 HA2309 UK209 38.100 1-1/2 45 85 30 22 3200 1850 0.52 HE2309 50 11 65 40 H 2309 41.275 1-5/8 HS2310 42.862 1-11/16 HA2310 UK210 44.450 1-3/4 50 90 31 23 3600 2100 0.56 HE2310 55 12 70 45 H 2310 47.625 1-7/8 HS2311 49.212 1-15/16 HA2311 UK211 50 55 100 33 24 4450 2660 0.77 H 2311 59 12 75 50.800 2 HE2311 UK212 53.975 2-1/8 60 110 36 27 5350 3300 1.01 HS2312 62 13 80 55 H 2312 55.562 2-3/16 HA2313 57.150 2-1/4 HE2313 UK213 60 65 120 38 28 5850 3650 1.27 H 2313 65 14 85 60.325 2-3/8 HS2313 61.912 2-7/16 HA2315 UK215 63.500 2-1/2 75 130 41 30 6750 4400 1.52 HE2315 73 15 98 65 H 2315 68.262 2-11/16 HA2316 UK216 69.850 2-3/4 80 140 44 32 7400 4750 1.85 HE2316 78 17 105 70 H 2316 74.612 2-15/16 HA2317 UK217 75 85 150 46 34 8550 5600 2.30 H 2317 82 18 110 76.200 3 HE2317 79.375 3-1/8 HS2318 UK218 80 90 160 49 36 9800 6450 3.10 H 2318 86 18 120 80.962 3-3/16 HA2318 208
BALL BRG UNITS Inserts: Spherical O/D UKX UK X00 Tapered Bore With Adapters Shaft Diameter: 19.050 90 mm Part No. Example: Bearing to suit 1-1/8 shaft, order: UK X06 + HS2307 Bearing Shaft Diameter Dimensions in mm Basic Load Ratings Wt Adapter Dimensions in mm Number mm inch d D B i B e Dyn Stat kg No. L Y W C C o UKX05 19.050 3/4 25 62 26 19 1990 1050 0.29 HE2305 35 8 38 20 H 2305 22.225 7/8 HS2306 UKX06 23.812 15/16 30 72 27 20 2260 1170 0.42 HA2306 38 8 45 25 H 2306 25.400 1 HE2306 28.575 1-1/8 HS2307 UKX07 30 35 80 29 21 2970 1650 0.54 H 2307 43 9 52 30.162 1-3/16 HA2307 31.750 1-1/4 HE2308 UKX08 34.925 1-3/8 40 85 30 22 3200 1850 0.60 HS2308 46 10 58 35 H 2308 36.512 1-7/16 HA2309 UKX09 38.100 1-1/2 45 90 31 23 3600 2100 0.66 HE2309 50 11 65 40 H 2309 41.275 1-5/8 HS2310 UKX10 42.862 1-11/16 50 100 33 24 4450 2660 0.88 HA2310 55 12 70 44.450 1-3/4 HE2310 45 H 2310 47.625 1-7/8 HS2311 UKX11 49.212 1-15/16 55 110 36 27 5350 3300 1.14 HA2311 59 12 75 50 H 2311 50.800 2 HE2311 UKX12 53.975 2-1/8 60 120 38 28 5850 3650 1.44 HS2312 62 13 80 55 H 2312 55.562 2-3/16 HA2313 UKX13 57.150 2-1/4 65 125 41 29 6350 4000 1.58 HE2313 65 14 85 60 H 2313 61.912 2-7/16 HA2315 UKX15 63.500 2-1/2 75 140 44 32 7400 4750 2.1 HE2315 73 15 98 65 H 2315 68.262 2-11/16 HA2316 UKX16 69.850 2-3/4 80 150 46 34 8550 5600 2.5 HE2316 78 17 105 70 H 2316 74.612 2-15/16 HA2317 UKX17 75 85 160 49 36 9800 6450 3.4 H 2317 82 18 110 76.200 3 HE2317 UKX18 80 90 170 52 38 11100 7400 3.7 H 2318 86 18 120 80.962 3-1/8 HA2318 UKX20 88.900 3-1/2 100 190 58 42 13600 9500 5.1 HE2320 97 20 130 90 H 2320 209
BALL BRG UNITS Inserts: Spherical O/D UK3 UK 300 Tapered Bore With Adapters Shaft Diameter: 19.050 125 mm Part No. Example: Bearing to suit 2 inch shaft, order: UK 311 + HE2311 Bearing Shaft Diameter Dimensions in mm Basic Load Ratings Wt Adapter Dimensions in mm Number mm inch d D B i B e Dyn Stat kg No. L Y W C C o UK305 19.050 3/4 25 62 26 22 2100 1080 0.30 HE2305 35 8 38 20 H 2305 22.225 7/8 HS2306 UK306 23.812 15/16 30 72 29 24 2720 1440 0.43 HA2306 38 8 45 25 H 2306 25.400 1 HE2306 28.575 1-1/8 HS2307 UK307 30 35 80 31 26 3400 1840 0.56 H 2307 43 9 52 30.162 1-3/16 HA2307 31.750 1-1/4 HE2308 UK308 34.925 1-3/8 40 90 34 28 4150 2300 0.76 HS2308 46 10 58 35 H 2308 36.512 1-7/16 HA2309 UK309 38.100 1-1/2 45 100 37 30 5400 3100 0.99 HE2309 50 11 65 40 H 2309 41.275 1-5/8 HS2310 UK310 42.862 1-11/16 50 110 40 32 6300 3650 1.28 HA2310 55 12 70 44.450 1-3/4 HE2310 45 H 2310 47.625 1-7/8 HS2311 UK311 49.212 1-15/16 55 120 43 34 7300 4300 1.62 HA2311 59 12 75 50 H 2311 50.800 2 HE2311 UK312 53.975 2-1/8 60 130 46 36 8350 5000 2.0 HS2312 62 13 809 55 H 2312 55.562 2-3/16 HA2313 UK313 57.150 2-1/4 65 140 48 38 9450 5750 2.5 HE2313 65 14 85 60 H 2313 60.325 2-3/8 HS2313 61.912 2-7/16 HA2315 UK315 63.500 2-1/2 75 160 54 42 11600 7400 3.6 HE2315 73 15 98 65 H 2315 68.262 2-11/16 HA2316 UK316 69.850 2-3/4 80 170 57 44 12500 8250 4.2 HE2316 78 17 105 70 H 2316 74.612 2-15/16 HA2317 UK317 75 85 180 60 46 13500 9200 4.9 H 2317 82 18 110 76.200 3 HE2317 79.375 3-1/8 HS2318 UK318 80 90 190 63 48 14500 10200 5.7 H 2318 86 18 120 80.962 3-3/16 HA2318 UK319 82.550 3-1/4 95 200 66 50 15600 11300 6.4 HE2319 90 19 125 85 H 2319 UK320 88.900 3-1/2 100 215 72 54 17700 13500 8.4 HE2320 97 20 130 90 H 2320 UK322 100 3-15/16 110 240 80 60 20900 17200 11.8 H 2322 105 21 145 101.600 4 HE2322 UK324 110 120 260 86 64 21100 17400 15.2 H 2324 112 22 155 UK326 115 130 280 92 68 23400 20200 18.7 H 2326 121 23 165 UK328 125 140 300 98 73 25800 23200 23.0 H 2328 131 24 180 210
BALL BRG UNITS UCS 200 Set Screw Type Bore Diameter: 12 ~ 90 mm Inserts: Parallel O/D UCS2 Part No. Example: Bearing to suit 45mm shaft, order: UCS 209 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Wt Number inch mm D B i B e N M G d s Dyn Stat kg C C o UCS201 12 47 31.0 17 12.7 18.3 4.5 M6X0.75 1300 635 0.21 UCS201-008 1/2 12.700 0.21 UCS202-009 9/16 14.288 0.20 UCS202 15 47 31.0 17 12.7 18.3 4.5 M6X0.75 1300 635 0.20 UCS202-010 5/8 15.875 0.19 UCS203 17 47 31.0 17 12.7 18.3 4.5 M6X0.75 1300 635 0.19 UCS203-011 11/16 17.462 0.18 UCS204-012 3/4 19.050 47 31.0 17 12.7 18.3 4.5 M6X0.75 1300 635 0.17 UCS204 20 0.17 UCS205-013 13/16 20.638 0.25 UCS205-014 7/8 22.225 0.23 UCS205-015 15/16 23.812 52 34.0 17 14.3 19.7 5.0 M6X0.75 1430 730 0.22 UCS205 25 0.20 UCS205-100 1 25.400 0.20 UCS206-101 1-1/16 26.988 0.36 UCS206-102 1-1/8 28.575 0.34 UCS206 30 62 38.1 19 15.9 22.2 5.0 M6X0.75 1990 1050 0.32 UCS206-103 1-3/16 30.162 0.32 UCS206-104 1-1/4 31.750 0.30 UCS207-104 1-1/4 31.750 0.55 UCS207-105 1-5/16 33.338 0.52 UCS207-106 1-3/8 34.925 72 42.9 20 17.5 25.4 6.0 M6X0.75 1990 1050 0.50 UCS207 35 0.49 UCS207-107 1-7/16 36.512 0.46 UCS208-107 1-7/16 36.512 0.73 UCS208-108 1-1/2 38.100 80 49.2 21 19.0 30.2 8.0 M8X1 2970 1650 0.70 UCS208-109 1-9/16 39.688 0.66 UCS208 40 0.65 UCS209-110 1-5/8 41.275 0.81 UCS209-111 1-11/16 42.862 85 49.2 22 19.0 30.2 8.0 M8X1 3200 1850 0.77 UCS209-112 1-3/4 44.450 0.73 UCS209 45 0.71 UCS210-113 1-13/16 46.038 0.91 UCS210-114 1-7/8 47.625 0.86 UCS210-115 1-15/16 49.212 90 51.6 23 19.0 32.6 9.0 M10X1.25 3600 2100 0.81 UCS210 50 0.79 UCS210-200 2 50.800 0.76 UCS211-200 2 50.800 1.23 UCS211-201 2-1/16 52.388 1.17 UCS211-202 2-1/8 53.975 100 55.6 24 22.2 33.4 9.0 M10X1.25 4450 2660 1.11 UCS211 55 1.07 UCS211-203 2-3/16 55.562 1.05 UCS212-204 2-1/4 57.150 1.65 UCS212-205 2-5/16 58.738 110 65.1 27 25.4 39.7 10.0 M10X1.25 5350 3300 1.57 UCS212 60 1.51 UCS212-206 2-3/8 60.325 1.50 UCS213-207 2-7/16 61.912 1.97 UCS213-208 2-1/2 63.500 120 65.1 28 25.4 39.7 10.0 M10X1.25 5850 3650 1.89 UCS213 65 1.81 UCS214-210 2-5/8 66.675 2.3 UCS214-211 2-11/16 68.262 125 74.6 29 30.2 44.4 12.0 M12X1.5 6350 4000 2.2 UCS214-212 2-3/4 69.850 2.1 UCS214 70 2.1 UCS215-213 2-13/16 71.438 2.6 UCS215-214 2-7/8 73.025 2.5 UCS215-215 2-15/16 74.612 130 77.8 30 33.3 44.5 12.0 M12X1.5 6750 4400 2.4 UCS215 75 2.4 UCS215-300 3 76.200 2.3 211
BALL BRG UNITS UCS 200 Inserts: Parallel O/D AELS2 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Wt Number inch mm D B i B e N M G d s Dyn Stat kg C C o UCS216-302 3-1/8 79.375 2.9 UCS216 80 140 82.6 32 33.3 49.3 12.0 M12X1.5 7400 4750 2.8 UCS216-303 3-3/16 80.962 2.7 UCS217-304 3-1/4 82.550 150 85.7 34 34.1 51.6 12.0 M12X1.5 8550 5600 3.6 UCS217 85 3.4 UCS218-305 3-7/16 87.312 4.6 UCS218-306 3-1/2 88.900 160 96.0 36 39.7 56.3 12.0 M12X1.5 9800 6450 4.4 UCS218 90 4.3 AELS 200 Eccentric Locking Collar Type Bore Diameter: 12 ~ 60.325 mm Part No. Example: Bearing to suit 20mm shaft, order: AELS 204 Bearing Bore Diameter Dimensions in mm Basic Load Ratings Eccentric Wt Number inch mm D L B i B e N G d s Dyn Stat Collar kg C C o No. AELS201 12 40 28.6 19.1 12 6.5 5.0 M6X0.75 975 460 EC201 0.13 AELS201-008 1/2 12.700 EC201-8 0.13 AELS202-009 9/16 14.288 EC202-9 0.12 AELS202 15 40 28.6 19.1 12 6.5 5.0 M6X0.75 975 460 EC202 0.11 AELS202-010 5/8 15.875 EC202-10 0.11 AELS203 17 40 28.6 19.1 12 6.5 5.0 M6X0.75 975 460 EC203 0.10 AELS203-011 11/16 17.462 EC203-11 0.10 AELS204-012 3/4 19.050 47 31.0 21.5 14 7.5 5.0 M6X0.75 1300 635 EC204-12 0.18 AELS204 20 EC204 0.17 AELS205-013 13/16 20.638 EC205-13 0.25 AELS205-014 7/8 22.225 EC205-14 0.23 AELS205-015 15/16 23.812 52 31.0 21.5 15 7.5 5.0 M6X0.75 1430 730 EC205-15 0.22 AELS205 25 EC205 0.21 AELS205-100 1 25.400 EC205-16 0.20 AELS206-101 1-1/16 26.988 EC206-17 0.35 AELS206-102 1-1/8 28.575 EC206-18 0.33 AELS206 30 62 35.7 23.8 16 9.0 6.0 M8X1 1990 1050 EC206 0.32 AELS206-103 1-3/16 30.162 EC206-19 0.31 AELS206-104 1-1/4 31.750 EC206-20 0.29 AELS207-104 1-1/4 31.750 EC207-20 0.55 AELS207-105 1-5/16 33.338 EC207-21 0.52 AELS207-106 1-3/8 34.925 72 38.9 25.4 17 9.5 7.0 M10X1.25 2620 1430 EC207-22 0.50 AELS207 35 EC207 0.50 AELS207-107 1-7/16 36.512 EC207-23 0.47 AELS208-107 1-7/16 36.512 EC208-23 0.70 AELS208-108 1-1/2 38.100 80 43.7 30.2 18 11.0 7.0 M10X1.25 2970 1650 EC208-24 0.67 AELS208-109 1-9/16 39.688 EC208-25 0.64 AELS208 40 EC208 0.63 AELS209-110 1-5/8 41.275 EC209-26 0.75 AELS209-111 1-11/16 42.862 85 43.7 30.2 19 11.0 7.0 M10X1.25 3200 1850 EC209-27 0.71 AELS209-112 1-3/4 44.450 EC209-28 0.68 AELS209 45 EC209 0.68 AELS210-113 1-13/16 46.038 EC210-29 0.87 AELS210-114 1-7/8 47.625 EC210-30 0.83 AELS210-115 1-15/16 49.212 90 43.7 30.2 20 11.0 7.0 M10X1.25 3600 2100 EC210-31 0.79 AELS210 50 EC210 0.77 AELS210-200 2 50.800 EC210-32 0.75 AELS211-200 2 50.800 EC211-32 1.10 AELS211-201 2-1/16 52.388 EC211-33 1.05 AELS211-202 2-1/8 53.975 100 48.4 32.5 21 12.0 8.0 M12X1.5 4450 2660 EC211-34 1.00 AELS211 55 EC211 0.96 AELS211-203 2-3/16 55.562 EC211-35 0.95 AELS212-204 2-1/4 57.150 EC212-36 1.30 AELS212-205 2-5/16 58.738 110 53.1 37.2 22 13.5 8.0 M12X1.5 5350 3300 EC212-37 1.24 AELS212 60 EC212 1.19 AELS212-206 2-3/8 60.325 EC212-38 1.17 212
BALL BRG UNITS Silver Lube Corrosion Resistant Units Stainless Steel Bearing Inserts Effective, Efficient Sealing Food Grade Grease Approved to USDA H1 Wide Operating Temperature End Covers Available Thermoplastic Moulded Housing No coating No cracking No peeling Stainless Steel Grease nipple Bolt hole liners Set screws Flinger Seal core Bearing rings, cage and balls Withstands Frequent Washdowns Resisting Corrosion Detergents Chemicals Fungicides INTRODUCTION The Silver-Lube series is a range of corrosion resistant bearing units specifically for use in industries where frequent thorough washdowns are necessary, optimum hygiene standards are required and good chemical resistance is important over a wide temperature range. The units are available in pillow block, two bolt and four bolt flange configurations and are capable of accommodating initial misalignment from mounting errors. In operating the units have proven reliability in the most hostile applications. Relubrication is possible for long trouble-free life - minimising maintenance, maximising productivity and helping maintain hygiene standards. Silver-Lube housings are made from Valoxâ 420 thermoplastic resin which in addition to being non-corrodable is resistant to detergents and a wide range of chemicals. The housings are paint and coating free which prevents chipping or flaking and have smooth surfaces to assist thorough washdowns. The housing material also demonstrates fungicidal resistance. Silver-Lube bearing inserts are made from stainless steel, are provided with effective, efficient sealing arrangements, and are charged with a USDA H1 approved food grade grease as standard. Full technical specifications, application details and descriptions of the Silver-Lube range are provided within this document. 213
BALL BRG UNITS Silver Lube Series PNP, PSF, PSFT UNIT DIMENSIONS Silver-Lube mounting details are interchangeable with the traditional RHP Self-Lube range. Some non-critical dimensions do, however differ, see tables below. RHP Shaft Basic Housing L H H1 H2 J N N1 G A A1 B S Weight Designation Dia. Insert Group (kg) PNP20CR 20 J1020 2 127.2 33.3 14.2 65.9 94.9 11.0 14.2 M10 37.8 22.5 31.0 12.7 0.27 PNP3/4CR 3/4 J1020 2 127.2 33.3 14.2 65.9 94.9 11.0 14.2 M10 37.8 22.5 31.0 12.7 0.27 PNP25CR 25 J1025 3 140.2 36.5 14.5 71.9 104.9 11.0 14.2 M10 37.8 24.5 34.0 14.3 0.39 PNP1CR 1 J1025 3 140.2 36.5 14.5 71.9 104.9 11.0 14.2 M10 37.8 24.5 34.0 14.3 0.39 PNP30CR 30 J1030 4 162.2 42.9 17.8 83.9 118.9 14.0 18.2 M12 45.8 27.0 38.1 15.9 0.52 PNP1.3/16CR 1.3/16 J1030 4 162.2 42.9 17.8 83.9 118.9 14.0 18.2 M12 45.8 27.0 38.1 15.9 0.52 PNP1.1/4CR 1.1/4 J1030 4 162.2 42.9 17.8 83.9 118.9 14.0 18.2 M12 45.8 27.0 38.1 15.9 0.52 PNP35CR 35 J1035 5 167.2 47.6 18.0 94.9 126.9 14.0 18.2 M12 47.8 32.5 42.9 17.5 0.72 PNP1.1/4CR 1.1/4 J1035 5 167.2 47.6 18.0 94.9 126.9 14.0 18.2 M12 47.8 32.5 42.9 17.5 0.72 PNP1.7/16CR 1.7/16 J1035 5 167.2 47.6 18.0 94.9 126.9 14.0 18.2 M12 47.8 32.5 42.9 17.5 0.72 RHP Shaft Basic Housing L J G A A1 A4 B S Wt. Designation Dia. Insert Group kg. PSF20CR 20 J1020 2 86.5 63.5 M10 27.8 36.3 13.4 31.0 12.7 0.28 PSF3/4CR 3/4 J1020 2 86.5 63.5 M10 27.8 36.3 13.4 31.0 12.7 0.28 PSF25CR 25 J1025 3 95.0 70.0 M10 27.9 36.7 14.3 34.0 14.3 0.34 PSF1CR 1 J1025 3 95.0 70.0 M10 27.9 36.7 14.3 34.0 14.3 0.34 PSF30CR 30 J1030 4 107.5 83.0 M10 31.5 41.4 14.3 38.1 15.9 0.50 PSF1.3/16CR 1.3/16 J1030 4 107.5 83.0 M10 31.5 41.4 14.3 38.1 15.9 0.50 PSF1.1/4RCR 1.1/4 J1030 4 107.5 83.0 M10 31.5 41.4 14.3 38.1 15.9 0.50 PSF35CR 35 J1035 5 117.5 92.0 M12 34.8 46.9 15.5 42.9 17.5 0.74 PSF1.1/4CR 1.1/4 J1035 5 117.5 92.0 M12 34.8 46.9 15.5 42.9 17.5 0.74 PSF1.7/16CR 1.7/16 J1035 5 117.5 92.0 M12 34.8 46.9 15.5 42.9 17.5 0.74 RHP Shaft Basic Housing L H J G A A1 A4 B S Wt. Designation Dia. Insert Grp kg PSFT20CR 20 J1020 2 64.1 113.3 90.0 M10 26.5 33.7 11.4 31.0 12.7 0.24 PSFT3/4CR 3/4 J1020 2 64.1 113.3 90.0 M10 26.5 33.7 11.4 31.0 12.7 0.24 PSFT25CR 25 J1025 3 68.4 130.3 99.0 M10 29.1 36.7 13.4 34.0 14.3 0.30 PSFT1CR 1 J1025 3 68.4 130.3 99.0 M10 29.1 36.7 13.4 34.0 14.3 0.30 PSFT30CR 30 J1030 4 80.1 148.3 117.0 M10 30.5 41.2 13.4 38.1 15.9 0.44 PSFT1.3/16CR 1.3/16 J1030 4 80.1 148.3 117.0 M10 30.5 41.2 13.4 38.1 15.9 0.44 PSFT1.1/4RCR 1.1/4R J1030 4 80.1 148.3 117.0 M10 30.5 41.2 13.4 38.1 15.9 0.44 PSFT35CR 35 J1035 5 90.1 163.3 130.0 M12 32.8 43.4 16.1 42.9 17.5 0.64 PSFT1.1/4CR 1.1/4 J1035 5 90.1 163.3 130.0 M12 32.8 43.4 16.1 42.9 17.5 0.64 PSFT1.7/16CR 1.7/16 J1035 5 90.1 163.3 130.0 M12 32.8 43.4 16.1 42.9 17.5 0.64 Housing End Cover Dimension Dimension Dimension Group Reference D1 D2 L Group 2 P20P 36 50 30 Group 3 P25P 42 55 31 Group 4 P30P 50 64 35 Group 5 P35P 60 74 38 All dimensions in mm. END COVERS Polypropylene end covers are available to fit all Silver-Lube housings. End covers can be used at temperatures ranging from -20 C to +90 C. They may be used as additional protection for the bearing in adverse environmental conditions as well as an aid to meeting safety requirements. 214
BALL BRG UNITS Silver Lube Housings Silver-Lube housings are manufactured from Valoxa 420, a high quality, 30% glass filled thermoplastic polyester resin which has excellent strength, rigidity, dimensional stability and chemical resistance. Typical Properties of Valoxa 420 Imperial Units (SI Units) VALOX 420 ASTM PBT Resin Test 30% Glass Property Units Method Reinforced MECHANICAL Tensile Strength psi(mpa) D638 17,300(119) Elongation at Yield % D638 3 Flexural Strength psi(mpa) D790 27,500(189) Flexural Modulus psi(mpa) D790 1,100,000(7,600) Compressive Strength psi(mpa) D695 18,000(124) Shear Strength psi(mpa) D732 8,900(61) Izod Impact Strength D256 Notched 1/8 thick (3.2mm) ft-lb/in(j/m) 1.6(85) Unnotched 1/8 thick (3.2mm) ft-lb/in(j/m) 15(800) Gardner Impact 1/8 thick (3.2mm) ft-lb(j) Falling Dart Rockwell Hardness R-scale D785 118 PHYSICAL Specific Gravity D792 1.53 Specific Volume in 3 /lb(cm 3 /kg) D792 18.2(655) Water Absortion 24 hours % D570 0.06 The reported values are typical values only - they do not directly apply to the manufactured housing but to the Valoxa 420 resin itself. HYGIENE Silver-Lube housings are non-corrodable and are paint and coating free to prevent chipping and peeling. The smooth surfaces resist dirt, mould and bacterial making Silver-Lube units ideal for use in industries where cleanliness is paramount. In tests in accordance with ASTM G21-70, Valoxa resins have demonstrated fungicidal resistance to: Aspergillus niger Penicillium faneculosium Chaetomium globosum Giiocladium virens Aureobasidium pullulans CHEMICAL RESISTANCE In general, Silver-Lube housings have excellent resistance to a wide variety of chemicals. In very generalised terms resistance by chemical category can be summarised as: Chemical Category Performance Acids Excellent Bases Good to Limited Organic Solvents Excellent to Fair Ketones and Esters Fair to Limited Chlorinated Solvents Excellent to Limited Salts Excellent Automotive Media Excellent to Fair More detailed results from testing Valoxa 420 resin in various media are listed in the adjacent table. This data describes exposure to a specific chemical under specific time, temperature and concentration situations, but not in combination with other chemical agents or environmental factors. It is therefore important that the user assess each application with regard to combined chemical exposures and environmental conditions. Chemical Resistance of Valoxa 420 (All data expressed in terms of % retention of tensile strength) xx = brittle Immersion Media Days Temp C % ACIDS 10% Hydrochloric Acid 30 25 89 90 (77 F) 85 10% Sulfuric Acid 30 25 97 90 94 36% Sulfuric Acid 30 25 97 90 97 30 60 84 90 (140 F) 60 10% Acetic Acid 30 25 88 90 88 BASES 5% Potassium Hydroxide 30 25 88 90 10 10% Sodium Hydroxide 30 25 xx 90 xx 10% Ammonium Hydroxide 30 25 96 90 87 SALTS 10% Zinc Chloride 30 25 97 90 94 10% Calcium Chloride 30 25 98 90 98 5% Sodium Chloride 30 25 97 90 97 ORGANIC SOLVENTS Ethyl Alcohol 30 25 99 90 96 Methyl Alcohol 30 25 91 90 82 Isopropyl Alcohol 30 25 100 90 100 IPA-Water(50/50) 30 25 98 90 97 GENERAL AND AUTOMOTIVE Heptane 30 25 99 90 99 Acetone 30 25 86 90 74 Methylethylketone 30 25 90 90 80 Ethyl Acetate 30 25 96 90 86 Methylene Chloride 30 25 54 90 54 Ethylene Glycol 30 25 100 90 100 Motor Oil 30 25 100 90 100 30 121 96 90 (250 F) 63 The reported values are typical values only - they do not directly apply to the manufactured housings but to the Valox 420 resin itself. 215
BALL BRG UNITS Graph 1: Strength retention after 6 months in water Silver Lube Housings WATER AND STEAM RESISTANCE Silver-Lube housings are suitable for use in applications where frequent washdowns occurs. After continuous immersion in water, Valox 420 resins exhibit very little loss of strength at water temperatures up to 150 F(65 C). Higher temperatures may be endured on an intermittent basis, but are not recommended for continuous use due to the associated loss of housing strength. See graph 1. Silver-Lube housings are not recommended for prolonged immersion or extended exposure to water vapour. In applications where prolonged water vapour exposure occurs some loss of housing strength may result. For more information please contact NSK-RHP. Graph 2: Tensile strength versus temperature (Valox 420 resin) ULTRAVIOLET RESISTANCE Valox 420-1001 (natural coloured) resin has been tested for resistance to ultraviolet ageing by exposure to direct sunlight in Florida and in Arizona for five years. Valox 420-1001 retained approximately 75% of its original strength, toughness and flexibility after five years of Florida and Arizona exposure. HEAT RESISTANCE The operating temperature range of Silver-Lube Valox 420 resin housings is -20 C to +90 C. Higher temperatures may be endured for short periods, for example during cleaning. However, where peak temperatures exceed +100 C for an extended period please contact NSK- RHP. The maximum housing loads published in this catalogue are based on tests conducted at 20 C. The tensile strength of Valox 420 resin varies with temperature, see graph 2, above. Bearing Operating Temperature Housing Temperature/Strength Factor -20 C 1.00-10 C 1.00 0 C 1.00 10 C 1.00 20 C 1.00 30 C 0.85 40 C 0.75 50 C 0.65 60 C 0.55 70 C 0.50 80 C 0.45 90 C 0.40 Designers and end users must ensure that housing strength is adequate at the unit operating temperature by adjusting the published housing strength at 20 C, detailed in Tables 8, 9 and 10 by using the Housing Temperature/Strength Factor listed in Table 7. For example, the maximum housing load for a bearing operating at 40 C is 1.75 of the published maximum housing load at 20 C. When evaluating housing strength it is important to establish the bearing operating temperature and not to consider the ambient temperature alone. Bearing operating temperature is dependent on ambient temperature and bearing load and speed. For high speed applications, bearing temperatures in excess of 60 C are common. Please consult NSK-RHP in case of difficulty. 216
BALL BRG UNITS Silver Lube Housings HOUSING STRENGTH Housing load carrying capacity varies depending on the application loading regime, which may be intermittent, continuous or cyclic. Maximum housing loads are given in the tables below. These loads must not be exceeded without prior consultation with NSK-RHP. Published housing maximum load capacities do not allow for any reduction in housing strength caused by exposure of the housing to chemicals, water, steam, heat, ultraviolet light or any combination of these factors. If any of these factors are present in the application the designer or end user must establish the effect of these exposures and reduce the published maximum housing load accordingly. To maximise load carrying capacity it is recommended that washers are used with the fixing bolts. The tables below also detail maximum fixing bolt tightening torques. RHP Maximum Housing Load (N) at 20 C Max Designation F1 F2 Fixing Intermittent Continuous Cyclic Intermittent Cont. Cyclic Bolt Loading Loading Loading Loading Loading Loading Torque (Nm) PSF20CR 3100 1600 900 1300 700 400 18 PSF3/4CR 3100 1600 900 1300 700 400 18 PSF25CR 3500 1700 1000 1300 700 400 25 PSF1CR 3500 1700 1000 1300 700 400 25 PSF30CR 4600 2300 1300 2200 1100 600 30 PSF1.3/16CR 4600 2300 1300 2200 1100 600 30 PSF1.1/4RCR 4600 2300 1300 2200 1100 600 30 PSF35CR 6200 3100 1700 2600 1300 700 35 PSF1.1/4CR 6200 3100 1700 2600 1300 700 35 PSF1.7/16CR 6200 3100 1700 2600 1300 700 35 RHP Maximum Housing Load (N) at 20 C Max. Designation F1 F2 F3 Fix Interm Cont Cyc Interm Cont Cyc Interm Cont Cyc Bolt Load Load Load Load Load Load Load Load Load Torque (Nm) PSFT20CR 4400 2200 1200 1900 900 500 1300 700 400 18 PSFT3/4CR 4400 2200 1200 1900 900 500 1300 700 400 18 PSFT25CR 4400 2200 1200 3000 1500 800 1400 700 400 25 PSFT1CR 4400 2200 1200 3000 1500 800 1400 700 400 25 PSFT30CR 5900 2900 1600 3300 1600 900 2000 1000 500 30 PSFT1.3/16CR 5900 2900 1600 3300 1600 900 2000 1000 500 30 PSFT1.1/4RCR 5900 2900 1600 3300 1600 900 2000 1000 500 30 PSFT35CR 6400 3200 1700 3900 2000 1100 2800 1400 800 35 PSFT1.1/4CR 6400 3200 1700 3900 2000 1100 2800 1400 800 35 PSFT1.7/16CR 6400 3200 1700 3900 2000 1100 2800 1400 800 35 RHP Maximum Housing Load (N) at 20 C Max Designation P1 P2 P3 P4 Fix Interm Cont Cyc Interm Cont Cyc Interm Cont Cyc Interm Cont Cyc Bolt Load Load Load Load Load Load Load Load Load Load Load Load Torque (Nm) PNP20CR 3500 1700 800 2800 1400 800 2600 1300 700 1300 700 400 18 PNP3/4CR 3500 1700 800 2800 1400 800 2600 1300 700 1300 700 400 18 PNP25CR 4000 2000 1000 3100 1500 800 2600 1300 700 1700 900 500 25 PNP1CR 4000 2000 1000 3100 1500 800 2600 1300 700 1700 900 500 25 PNP30CR 5000 2500 1200 3500 1800 1000 4000 2000 1100 2600 1300 700 30 PNP1.3/16CR 5000 2500 1200 3500 1800 1000 4000 2000 1100 2600 1300 700 30 PNP1.1/4RCR 5000 2500 1200 3500 1800 1000 4000 2000 1100 2600 1300 700 30 PNP35CR 6000 3000 1500 4300 2100 1200 4100 2100 1100 3200 1600 900 35 PNP1.1/4CR 6000 3000 1500 4300 2100 1200 4100 2100 1100 3200 1600 900 35 PNP1.7/16CR 6000 3000 1500 4300 2100 1200 4100 2100 1100 3200 1600 900 35 217
BALL BRG UNITS Silver Lube Bearing Inserts Silver-Lube bearing inserts are manufactured from QD51, a modified 440C type stainless steel, and are charged with Chevron Poly FM 2, a USDA H1 approved food grade grease. Bearing insert operating temperature range is -20 C to +90 C. Component Materials Standard Bearing Ball Flinger Set Cage Rings Screw JIS SUS440C SUS440C SUS304 SUS410 SUS304 AISI/ASTM AISI440C AISI440C AISI304 AISI410 AISI304 Insert Designation, Dimensions and Weights RHP Bore D C B S S1 r h M SS Cr (N) Cor (N) Weight Designation Dia. kg. J1020-20GCR 20 47 16 31.0 12.7 18.3 1.5 4.0 5.0 M6 9910 5350 0.16 J1020-3/4GCR 3/4 47 16 31.0 12.7 18.3 1.5 4.0 5.0 M6 9910 5350 0.16 J1025-25GCR 25 52 17 34.0 14.3 19.7 1.5 3.5 5.5 M6 10820 6300 0.20 J1025-1GCR 1 52 17 34.0 14.3 19.7 1.0 3.5 5.5 M6 10820 6300 0.20 J1030-30GCR 30 62 19 38.1 15.9 22.2 1.5 4.5 6.0 M6 15000 9050 0.32 J1030-1.3/16GCR 1.3/16 62 19 38.1 15.9 22.2 1.0 4.5 6.0 M6 15000 9050 0.32 J1030-1.1/4GCR 1.1/4 62 19 38.1 15.9 22.2 1.0 4.5 6.0 M6 15000 9050 0.32 J1035-35GCR 35 72 20 42.9 17.5 25.4 2.0 4.5 6.5 M8 19820 12300 0.48 J1035-1.1/4GCR 1.1/4 72 20 42.9 17.5 25.4 2.0 4.5 6.5 M8 19820 12300 0.48 J1035-1.7/16GCR 1.7/16 72 20 42.9 17.5 25.4 1.5 4.5 6.5 M8 19820 12300 0.48 Cr = basic dynamic load rating. Contact NSK-RHP for guidance on life estimation. Cor = basic static load rating. All dimensions in mm except inch bores. Shaft Tolerances and Permissable Speeds Basic ISO h7 ISO h9 Bearing Bearing Shaft Tolerance Bearing Shaft Tolerance Insert Limiting (0.001 mm Units) Limiting (0.001 mm Units) Speed High Low Speed High Low (RPM) (RPM) J1020 2900 0-21 1490 0-52 J1025 2600 0-21 1300 0-52 J1030 2180 0-21 1090 0-52 J1035 1870 0-25 940 0-62 Bearing insert permissible speed is dependent on shaft tolerance. For higher speed applications an ISO h7 shaft tolerance is recommended. An ISO h9 shaft tolerance may be used for low speed applications. Set Screw Tightening Torques RHP Designation Set Screw Max Tightening Torque (Nm) J1020-20GCR M6 x 6.5 LONG 4 J1020-3/4GCR M6 x 6.5 LONG 4 J1025-25GCR M6 x 6.5 LONG 4 J1025-1GCR M6 x 6.5 LONG 4 J1030-30GCR M6 x 6.5 LONG 4 J1030-1.3/16GCR M6 x 6.5 LONG 4 J1030-1.1/4GCR M6 x 6.5 LONG 4 J1035-35GCR M8 x 9.0 LONG 8 J1035-1.1/4GCR M8 x 9.0 LONG 8 J1035-1.7/16GCR M8 x 9.0 LONG 8 Set screws for Silver-Lube bearing inserts are manufactured from stainless steel and can fracture if overtightened. The limiting set screw torques listed below should not be exceeded. Bore Tolerance Silver-Lube inner ring bore tolerances are on the plus side of the nominal bore. This enables the bearing to slip freely over standard shafting. Nominal Bore Bore Tolerance Diameter d (mm) (0.001 mm Units) Over Including Max Min 10 18 +18 0 18 30 +21 0 30 50 +25 0 218
LINEAR MOTION Ball Screws & Nuts Ballscrews convert rotary motion into linear motion. they are similar to Acme screws, but are three times more efficient. Ballscrews range from standard off-the-shelf rolled ballscrews, to ultra-accurate ground screws. Accuracy Class ISO Load Accuracy Class 300mm G200 Rolled 10 0.200/300mm G100 Rolled 9 0.100/300mm G50 Rolled 7 0.050/300mm G25 Rolled 5 0.025/300mm P25 Ground 5 0.025/300mm P10 Ground 3 0.010/300mm P5 Ground 1 0.005/300mm Nuts Model Nom Load No. Max. Axial Load Capacity No. Mass Mass R.H cir- Spd Play (N) Balls Screw Nut mm mm cuit RPM mm Dyn. Status kg/m kg d 0 P h0 l C 0 C 0a Single Nut Right hand thread Single Start with Backlash Accuracy classes 9 and 10 RM-1605-UF 16 5 3 3000 0.09 9000 12000 45 1.600 0.240 25 5 3 3000 0.09 10000 20000 69 3.900 0.350 32 5 4 3000 0.09 14000 36000 116 6.400 0.450 40 5 5 2500 0.09 17000 60000 180 9.900 0.650 40 10 3 2500 0.18 36000 66000 54 9.900 1.250 50 10 5 2000 0.18 58000 143000 115 15.400 2.000 63 10 5 1500 0.18 62000 186000 140 24.500 2.450 80 10 7 1000 0.18 85000 350000 52 39.400 3.000 Ballscrews Model Screw Shaft mm Single Nut mm Max d 1 d 4 D 1 D 3 D 4 D 5 D 6 L L 1 L 3 L 7 Lth RM-1605-UF 1500 15.7 12 28.5 21 38 6x5.5 48 44 5.5 10 2500 24.7 21 38.5 32 50 6x6.6 62 44 5.5 10 4000 31.7 28 45.5 38 58 6x6.6 70 49 5.5 10 4000 39.7 36 53.5 46 68 6x6.6 80 57 5.5 12 4000 39.7 33 63.5 50 78 6x9.0 95 70 9.5 4 12 5000 49.7 43 72.5 60 90 6x11.0 110 93 9.5 4 15 5000 62.7 56 85.5 72 105 6x11.0 125 94 9.5 4 16 6000 82.9 76 105.5 92 125 6x14.0 150 120 20.0 4 20 Double nuts are available for the above ballscrews. 359
SPECIALTY NSK Spherical Roller Bearing Molded-Oil Molded-Oil TM bearings are lubricated with NSK s own oil-impregnated material. Molded- Oil TM consists of lubricating oil and polyolefin resin that has an affinity for oil. Oil slowly seeping from this material provides ample lubrication to the bearing for extended periods. Used for applications in which bearings are exposed to large quantities of liquids such as water. Bearing Nomenclature Example: 22212 L12 CAM K C3 Spherical roller bearings (Bearing type); Width series 2 (Bearing series symbols); Diameter series 3 (Bearing series symbols); Bearing bore 90mm (Bore number). Molded-oil for high-speed (L11 is for general use) (L12 is for high speed) Machine brass cage (Cage type symbol) Tapered bore Radial clearance C3 (Internal clearance symbol) 366 Boundary Dimensions (mm) Basic Load Bearing Numbers Bore Outside Chamfer Ratings (N) Width Diameter Diameter Dim. (min) Cr Cor 21307L12CAM 35 80 21 1.5 71000 76000 21308L11CAM 40 90 23 1.5 82000 93000 22308L11CAM 40 90 33 1.5 122000 129000 22209L11CAM 45 85 23 1.1 78000 88000 22309L12CAM 45 100 36 1.5 148000 167000 22210L11CAM 50 90 23 1.1 82000 93000 22311L12CAM 55 120 43 2.0 209000 241000 22212L12CAM 60 110 28 1.5 127000 154000 22213L11CAM 65 120 31 1.5 152000 190000 22313L11CAM 65 140 48 2.1 265000 315000 22313L12CAM 65 140 48 2.1 265000 315000 22214L11CAM 70 125 31 1.5 163000 205000 22315L12CAM 75 160 55 2.1 340000 415000 22216L11CAM 80 140 33 2.0 181000 232000 22217L12CAM 85 150 36 2.0 215000 276000 22218L12CAM 90 160 40 2.0 256000 340000 22219L12CAM 95 170 43 2.1 296000 395000 23120L11CAM 100 165 52 2.0 345000 530000 22320L11CAM 100 215 73 3.0 600000 785000 22222L12CAM 110 200 53 2.1 425000 585000 23024L11CAM 120 180 46 2.0 315000 525000 23124L12CAM 120 200 62 2.0 465000 720000 22226L11CAM 130 230 64 3.0 565000 815000 23932L11CAM 160 220 45 2.0 360000 675000 Molded Oil Spherical Roller Bearings Bearing numbers other than those given in the table can also be produced.
Accessories Steel Balls... 450 Cylindrical Rollers... 451 Needle Rollers... 452 Adapter Sleeves... 453 Series H2, HE2,HS2,HA2, H3, HE3,HS3,HA3... 453 Series H23, HE23, HS23,HA23... 455 Series H30, HE30, H31, HE31, H32... 456 Withdrawal Sleeves... 457 Series AH3, AH22... 457 Series AH23, AH30, AH31, AH32... 458 Lock Nuts... 459 Series AN... 459 Lock Washers... 460 Series AW... 460 449
ACCESSORIES Imperial Steel Balls Imperial & Metric Part No. Chrome Stainless Phosphor Nickel Size Steel Steel Bronze Cad Note: Part Chrome Stainless Nickel No. Steel Steel Cad 0.3 0.3mm C/S 0.3mm S/S 0.3mm N/C 0.4 0.4mm C/S 0.4mm S/S 0.4mm N/C 0.5 0.5mm C/S 0.5mm S/S 0.5mm N/C 0.6 0.6mm C/S 0.6mm S/S 0.6mm N/C 0.7 0.7mm C/S 0.7mm S/S 0.7mm N/C 0.8 0.8mm C/S 0.8mm S/S 0.8mm N/C 1.0 1mm C/S 1mm S/S 1mm N/C 1.2 1.2mm C/S 1.2mm S/S 1.2mm N/C 1.5 1.5mm C/S 1.5mm S/S 1.5mm N/C 2.0 2mm C/S 2mm S/S 2mm N/C 2.5 2.5mm C/S 2.5mm S/S 2.5mm N/C 3.0 3mm C/S 3mm S/S 3mm N/C 3.5 3.5mm C/S 3.5mm S/S 3.5mm N/C 4.0 4mm C/S 4mm S/S 4mm N/C 4.5 4.5mm C/S 4.5mm S/S 4.5mm N/C 5.0 5mm C/S 5mm S/S 5mm N/C 5.5 5.5mm C/S 5.5mm S/S 5.5mm N/C 6.0 6mm C/S 6mm S/S 6mm N/C 6.5 6.5mm C/S 6.5mm S/S 6.5mm N/C 7.0 7mm C/S 7mm S/S 7mm N/C 7.5 7.5mm C/S 7.5mm S/S 7.5mm N/C 8.0 8mm C/S 8mm S/S 8mm N/C 8.5 8.5mm C/S 8.5mm S/S 8.5mm N/C 9.0 9mm C/S 9mm S/S 9mm N/C 10.0 10mm C/S 10mm S/S 10mm N/C 11.0 11mm C/S 11mm S/S 11mm N/C 11.5 11.5mm C/S 11.5mmS/S 11.5mm N/C 12.0 12mm C/S 12mm S/S 12mm N/C 13.0 13mm C/S 13mm S/S 13mm N/C 14.0 14mm C/S 14mm S/S 14mm N/C 15.0 15mm C/S 15mm S/S 15mm N/C 16.0 16mm C/S 16mm S/S 16mm N/C 17.0 17mm C/S 17mm S/S 17mm N/C 18.0 18mm C/S 18mm S/S 18mm N/C 19.0 19mm C/S 19mm S/S 19mm N/C 20.0 20mm C/S 20mm S/S 20mm N/C 21.0 21mm C/S 21mm S/S 21mm N/C 22.0 22mm C/S 22mm S/S 22mm N/C 23.0 23mm C/S 23mm S/S 23mm N/C 24.0 24mm C/S 24mm S/S 24mm N/C 25.0 25mm C/S 25mm S/S 25mm N/C 26.0 26mm C/S 26mm S/S 26mm N/C 28.0 28mm C/S 28mm S/S 28mm N/C 30.0 30mm C/S 30mm S/S 30mm N/C 32.0 32mm C/S 32mm S/S 32mm N/C 34.0 34mm C/S 34mm S/S 34mm N/C 35.0 35mm C/S 35mm S/S 35mm N/C 36.0 36mm C/S 36mm S/S 36mm N/C 38.0 38mm C/S 38mm S/S 38mm N/C 40.0 40mm C/S 40mm S/S 40mm N/C 45.0 45mm C/S 45mm S/S 45mm N/C 50.0 50mm C/S 50mm S/S 50mm N/C 55.0 55mm C/S 55mm S/S 55mmN/C 60.0 60mm C/S 60mm S/S 60mm N/C 65.0 65mm C/S 65mm S/S 65mm N/C 450 Nominal Size, Basic Diameters, and Mass Metric Sizes not listed in Stainless Steel, Phosper Bronze and Nickelcad may be available to special order. Larger Sizes are also available. Contact your nearest branch for details. 0.025 0.025 C/S 0.025 S/S 0.025 P/B 0.025 N/C 1/32 1/32 C/S 1/32 S/S 1/32 P/B 1/32 N/C 3/64 3/64 C/S 3/64 S/S 3/64 P/B 3/64 N/C 1/16 1/16 C/S 1/16 S/S 1/16 P/B 1/16 N/C 5/64 5/64 C/S 5/64 S/S 5/64P/B 5/64 N/C 3/32 3/32 C/S 3/32 S/S 3/32 P/B 3/32 N/C 7/64 7/64 C/S 7/64 S/S 7/64 P/B 7/64 N/C 1/8 1/8 C/S 1/8 S/S 1/8 P/B 1/8 N/C 9/64 9/64 C/S 9/64 S/S 9/64 P/B 9/64 N/C 5/32 5/32 C/S 5/32 S/S 5/32 P/B 5/32 N/C 3/16 3/16 C/S 3/16 S/S 3/16 P/B 3/16 N/C 7/32 7/32 C/S 7/32 S/S 7/32 P/B 7/32 N/C 15/64 15/64 C/S 15/64 S/S 15/64 P/B 15/64 N/C 1/4 1/4 C/S 1/4 S/S 1/4 P/B 1/4 N/C 17/64 17/64 C/S 17/64 S/S 17/64 P/B 17/64 N/C 9/32 9/32 C/S 9/32 S/S 9/32 P/B 9/32N/C 5/16 5/16 C/S 15/16 S/S 15/16 P/B 15/16 N/C 11/32 11/32 C/S 11/32 S/S 11/32 P/B 11/32 N/C 3/8 3/8 C/S 3/8 S/S 3/8 P/B 3/8 N/C 13/32 13/32 C/S 13/32 S/S 13/32 P/B 13/32N/C 7/16 7/16 C/S 7/16 S/S 7/16 P/B 7/16 N/C 15/32 15/32 C/S 15/32 S/S 15/32 P/B 15/32 N/C 1/2 1/2 C/S 1/2 S/S 1/2 P/B 1/2 N/C 17/32 17/32 C/S 17/32 S/S 17/32 P/B 17/32 N/C 9/16 9/16 C/S 9/16 S/S 9/16 P/B 9/16 N/C 19/32 19/32 C/S 19/32 S/S 19/32 P/B 19/32 N/C 5/8 5/8 C/S 5/8 S/S 5/8 P/B 5/8 N/C 21/32 21/32 C/S 21/32 S/S 21/32 P/B 21/32 N/C 11/16 11/16 C/S 11/16 S/S 11/16 P/B 11/16 N/C 23/32 23/32 C/S 23/32 S/S 23/32 P/B 23/32 N/C 3/4 3/4 C/S 3/4 S/S 3/4 P/B 3/4 N/C 25/32 25/32 C/S 25/32 S/S 25/32 P/B 25/32 N/C 13/16 13/16 C/S 13/16 S/S 13/16 P/B 13/16 N/C 27/32 27/32 C/S 27/32 S/S 27/32 P/B 27/32 N/C 7/8 7/8 C/S 7/8 S/S 7/8 P/B 7/8 N/C 29/32 29/32 C/S 29/32 S/S 29/32 P/B 29/32 N/C 15/16 15/16 C/S 15/16 S/S 15/16 P/B 15/16 N/C 31/32 31/32 C/S 31/32 S/S 31/32 P/B 31/32 N/C 1 1 C/S 1 S/S 1 P/B 1 N/C 1-1/16 1-1/16 C/S 1-1/16S/S 1-1/16 P/B 1-1/16 N/C 1-1/8 1-1/8 C/S 1-1/8 S/S 1-1/8 P/B 1-1/8N/C 1-3/16 1-3/16 C/S 1-3/16 S/S 1-3/16 P/B 1-3/16 N/C 1-1/4 1-1/4 C/S 1-1/4 S/S 1-1/4 P/B 1-1/4N/C 1-5/16 1-5/16 C/S 1-5/16 S/S 1-5/16 P/B 1-5/16 N/C 1-3/8 1-3/8 C/S 1-3/8 S/S 1-3/8 P/B 1-3/8N/C 1-7/16 1-7/16 C/S 1-7/16 S/S 1-7/16 P/B 1-7/16 N/C 1-1/2 1-1/2 C/S 1-1/2 S/S 1-1/2 P/B 1-1/2 N/C 1-9/16 1-9/16 C/S 1-9/16 S/S 1-9/16 P/B 1-9/16 N/C 1-5/8 1-5/8 C/S 1-5/8 S/S 1-5/8 P/B 1-5/8N/C 1-11/16 1-11/16 C/S 1-11/16 S/S 1-11/16 P/B 1-11/16 N/C 1-3/4 1-3/4 C/S 1-3/4 S/S 1-3/4 P/B 1-3/4N/C 1-13/16 1-13/16 C/S 1-13/16 S/S 1-13/16 P/B 1-13/16 N/C 1-7/8 1-7/8 C/S 1-7/8 S/S 1-7/8 P/B 1-7/8N/C 1-15/16 1-15/16 C/S 1-15/16 S/S 1-15/16 P/B 1-15/16 N/C 2 2 C/S 2 S/S 2 P/B 2 N/C 2-1/8 2-1/8 C/S 2-1/8 S/S 2-1/8 P/B 2-1/8N/C 2-1/4 2-1/4 C/S 2-1/4 S/S 2-1/4 P/B 2-1/4N/C 2-3/8 2-3/8 C/S 2-3/8 S/S 2-3/8 P/B 2-3/8 N/C 2-1/2 2-1/2 C/S 2-1/2 S/S 2-1/2 P/B 2-1/2 N/C 2-5/8 2-5/8 C/S 2-5/8 S/S 2-5/8 P/B 2-5/8N/C 2-3/4 2-3/4 C/S 2-3/4 S/S 2-3/4 P/B 2-3/4 N/C 2-7/8 2-7/8 C/S 2-7/8 S/S 2-7/8 P/B 2-7/8 N/C 3 3 C/S 3 S/S 3 P/B 3 N/C 3-1/4 3-1/4 C/S 3-1/4 S/S 3-1/4 P/B 3-1/4N/C 3-1/2 3-1/2 C/S 3-1/2 S/S 3-1/2 P/B 3-1/2N/C 3-3/4 3-3/4 C/S 3-3/4 S/S 3-3/4 P/B 3-3/4 N/C 4 4 C/S 4 S/S 4 P/B 4N/C 4-1/4 4-1/4 C/S 4-1/4 S/S 4-1/4 P/B 4-1/4N/C 4-1/2 4-1/2 C/S 4-1/2 S/S 4-1/2 P/B 4-1/2N/C
ACCESSORIES Cylindrical Rollers Imperial & Metric Part No. in MM Diameter x Length 3MM X 3MM 3MM X 5MM 3.5MM X 5MM 4MM X 4MM 4MM X 6MM 4MM X 8MM 4.5MM X 4.5MM 4.5MM X 6MM 5MM X 5MM 5MM X 8MM 5MM X 10MM 5.5MM X 5.5MM 5.5MM X 8MM 6MM X 6MM 6MM X 8MM 6MM X 12MM 6.5MM X 6.5MM 6.5MM X 9MM 7MM X 7MM 7MM X 10MM 7MM X 14MM 7.5MM X 7.5MM 7.5MM X 11MM 8MM X 8MM 8MM X 12MM 9MM X 9MM 9MM X 14MM 10MM X 10MM 10MM X 14MM 11MM X 11MM 11MM X 15MM 12MM X 12MM 12MM X 18MM 13MM X 13MM 13MM X 20MM 14MM X 14MM 14MM X 20MM 15MM X 15MM Metric Rollers - Cylindrical Part No. in MM Diameter x Length 15MM X 22MM 16MM X 16MM 16MM X 24MM 17MM X 17MM 17MM X 24MM 18MM X 18MM 18MM X 26MM 19MM X 19MM 19MM X 28MM 20MM X 20MM 20MM X 30MM 21MM X 21MM 21MM X 30MM 22MM X 22MM 22MM X 34MM 23MM X 23MM 23MM X 34MM 24MM X 24MM 24MM X 36MM 25MM X 25MM 25MM X 36MM 26MM X 26MM 26MM X 40MM 28MM X 28MM 28MM X 44MM 30MM X 30MM 30MM X 48MM 32MM X 32MM 32MM X 52MM 34MM X 34MM 34MM X 55MM 36MM X 36MM 36MM X 58MM 38MM X 38MM 38MM X 62MM 40MM X 40MM 40MM X 65MM Note: Imperial Rollers - Cylindrical Part No. in Inches Diameter x Length 5/32 X 5/32 3/16 X 3/16 7/32 X 7/32 1/4 X 1/4 9/32 X 9/32 5/16 X 5/16 11/32 X 11/32 3/8 X 3/8 13/32 X 13/32 7/16 X 7/16 15/32 X 15/32 1/2 X 1/2 17/32 X 17/32 9/16 X 9/16 19/32 X 19/32 5/8 X 5/8 11/16 X 11/16 3/4 X 3/4 13/16 X 13/16 7/8 X 7/8 15/16 X 15/16 1 X 1 Larger sizes available. Contact your nearest branch for further details. 451
ACCESSORIES Needle Rollers Metric and Inch Ball-end Needle Roller Needle Rollers - Metric Part No. Diameter x Length 1MM X 5.8MM 1MM X 6.8MM 1MM X 7.8MM 1MM X 9.8MM 1.5MM X 5.8MM 1.5MM X 6.8MM 1.5MM X 7.8MM 1.5MM X 9.8MM 1.5MM x 11.8MM 1.5MM X 13.8MM 2MM X 6.8MM 2MM X 7.8MM 2MM X 9.8MM 2MM X 11.8MM 2MM X 13.8MM 2MM X 15.8MM 2MM X 17.8MM 2MM X 19.8MM 2MM X 21.8MM 2.5MM X 7.8MM 2.5MM X 9.8MM 2.5MM X 11.8MM 2.5MM X 13.8MM 2.5MM X 15.8MM 2.5MM X 17.8MM 2.5MM X 19.8MM 2.5MM X 21.8MM 2.5MM X 23.8MM 3MM X 9.8MM 3MM X 11.8MM 3MM X 13.8MM 3MM X 15.8MM 3MM X 17.8MM 3MM X 19.8MM 3MM X 21.8MM 3MM X 22.8MM 3MM X 23.8MM 3MM X 25.8MM 3MM X 27.8MM 3MM X 29.8MM 3.5MM X 11.8MM 3.5MM X 13.8MM 3.5MM X 15.8MM 3.5MM X 17.8MM 3.5MM X 19.8MM 3.5MM X 21.8MM 3.5MM X 23.8MM Part No. Diameter x Length 3.5MM X 25.8MM 3.5MM X 27.8MM 3.5MM X 29.8MM 3.5MM X 31.8MM 3.5MM X 34.8MM 4MM X 11.8MM 4MM X 13.8MM 4MM X 15.8MM 4MM X 17.8MM 4MM X 19.8MM 4MM X 21.8MM 4MM X 23.8MM 4MM X 25.8MM 4MM X 27.8MM 4MM X 29.8MM 4MM X 31.8MM 4MM X 34.8MM 4MM X 39.8MM 4.5MM X 17.8MM 4.5MM X 19.8MM 4.5MM X 21.8MM 4.5MM X 23.8MM 4.5MM X 25.8MM 4.5MM X 29.8MM 4.5MM X 31.8MM 4.5MM X 34.8MM 4.5MM X 37.8MM 4.5MM X 39.8MM 4.5MM X 44.8MM 5MM X 15.8MM 5MM X 19.8MM 5MM X 21.8MM 5MM X 23.8MM 5MM X 25.8MM 5MM X 27.8MM 5MM X 29.8MM 5MM X 34.8MM 5MM X 39.8MM 5MM X 49.8MM 6MM X 17.8MM 6MM X 21.8MM 6MM X 22MM 6MM X 23.8MM 6MM X 25MM 6MM X 25.8MM 6MM X 39.8MM Note: Other sizes available. Contact your nearest branch for further details..0469 X.250.0469 X.280.0469 X.310.0625 X.280.0625 X.406.0625 X.440.0625 X.500.0625 X.530.0627 X.250.0627 X.370.0627 X.490.0713 X.530.0721 X.478.0771 X.745.0772 X.505.0781 X.380.0781 X.440.0781 X.500.0781 X.620.0781 X.690.0781 X.750.0785 X.640.0792 X.396.0859 X.410.0907 X.745.0911 X.810.0922 X.707.0923 X.400.0928 X.620.0932 X.644.0937 X.700.0938 X.416.0938 X.380.0938 X.440.0938 X.500.0938 X.560.0938 X.620.0938 X.690.0938 X.750.0938 X.781.0938 X.810.0938 X.880.0940 X.344.0940 X.494.0950 X.500.0950 X.520.1012 X.572.1040 X.396.1050 X.310 Needle Rollers - Inch Part No. Diameter x Length Part No. Diameter x Length.1094 X.440.1094 X.750.1244 X.900.1250 X.460.1250 X.490.1250 x.500.1250 x.615.1250 x.690.1250 x.750.1250 x.850.1250 x.938.1250 x.940.1250 x 1.000.1250 x 1.125.1250 x 1.250.1548 x.958.1562 X.656.1562 X.750.1562 X.880.1562 X.900.1562 x 1.000.1562 x 1.120.1562 x 1.250.1582 X.562.1582 X.740.1582 X 1.014.1872 X 1.187.1875 x.527.1875 x.750.1875 x.880.1875 x 1.000.1875 x 1.120.1875 x 1.125.1875 x 1.187.1875 x 1.250.1875 x 1.375.1905 X.500.1905 X.443.1960 X.495.2182 x.752.2187 x.750.2188 X 1.120.2188 X 1.250.2188 X 1.500.2188 X 1.750.2325 x 1.000.2500 x 1.000.2500 X 1.190.2500 X 2.000 452
ACCESSORIES Adapter Sleeves Series H2, HE2,HS2,HA2, H3, HE3,HS3,HA3 Bore Diameter Number Tolerances for Adapter Sleeves Bore Diameter, d Deviation Length, L Deviation mm inch mm inch 04 ~ 10 ±0.05 ±0.0020 ±0.25 ±0.010 11 ~ 16 ±0.06 ±0.0024 ±0.25 ±0.010 17 ~ 24 ±0.07 ±0.0028 ±0.25 ±0.010 26 ~ 36 ±0.08 ±0.0031 ±0.25 ±0.010 38 ~ 48 ±0.09 ±0.0035 ±0.25 ±0.010 52 ~ 60 ±0.12 ±0.0047 ±0.50 ±0.020 64 ~ 80 ±0.15 ±0.0059 ±0.50 ±0.020 Adapter Nos. 1) Bore Shaft Dia. d 1 Corresponding Bearing Numbers H HE,HS,HA H H HE,HS HE,HS L L D 1 D 1 S S Self-Aligning HA HA Ball mm in. mm in. mm in. mm in. mm in. Bearings H204 17 0.669 30.162 1-3/16 24 0.945 32 1.260 7 0.276 1204K H205 HE205 20 0.787 19.050 3/4 26 1.024 38 1.496 8 0.315 1205K H206 HS206 22.225 7/8 HA206 23.812 15/16 HE206 25 0.984 25.400 1 27 1.063 45 1.772 8 0.315 1206K H207 HS207 30 1.181 28.575 1-1/8 29 1.142 52 2.047 9 0.354 1207K HA207 30.162 1-3/16 H208 HE208 35 1.378 31.750 1-1/4 31 1.220 58 2.283 10 0.394 1208K HA208 33.338 1-5/16 HS208 34.925 1-3/8 H209 HA209 36.512 1-7/16 HE209 40 1.575 38.100 1-1/2 33 1.299 65 2.559 11 0.433 1209K HS209 41.275 1-5/8 H210 HS210 41.275 1-5/8 HA210 42.862 1-11/16 HE210 45 1.772 44.450 1-3/4 35 1.378 70 2.756 12 0.472 1210K H211 HS211 47.625 1-7/8 HA211 49.212 1-15/16 HE211X 2) 50 1.969 50.800 2 37 1.457 75 2.953 12 0.472 1211K H212 HS212 55 2.165 53.975 2-1/8 38 1.496 80 3.150 13 0.512 1212K H213 HA213 55.562 2-3/16 HE213 60 2.362 57.150 2-1/4 40 1.575 85 3.346 14 0.551 1213K HS213 60.325 2-3/8 H215 HA215 61.912 2-7/16 HE215 65 2.559 63.500 2-1/2 43 1.693 98 3.858 15 0.591 1215K H216 HA216 68.262 2-11/16 HE216 70 2.756 69.850 2-3/4 46 1.811 105 4.134 17 0.669 1216K H217 HA217 74.612 2-15/16 HE217 75 2.953 76.200 3 50 1.969 110 4.331 18 0.709 1217K H218 HA218 80 3.150 82.550 3-1/4 52 2.047 120 4.724 18 0.709 1218K H219 HE219 85 3.346 82.550 3-1/4 55 2.165 125 4.921 19 0.748 1219K H220 HA220 87.312 3-7/16 HE220 90 3.543 88.900 3-1/2 58 2.283 130 5.118 20 0.787 1220K H222 HA222 100.012 3-15/16 HE222 100 3.937 101.600 4 63 2.480 145 5.709 21 0.827 1222K 1) Adapter numbers apply to adapter sleeve, lock-nut, and lock-washer assemblies. 2) The thread size of HE211 X is M55x1.5 and differs from the standard (M55x2.0). 3) The thread size of HE311 X is M55x1.5 and differs from the standard (M55x2.0). H=METRIC SHAFT HE=IMPERIAL SHAFT 453
ACCESSORIES Adapter Sleeves Series H2, HE2,HS2,HA2, H3, HE3,HS3,HA3 Adapter Nos. 1) Bore Shaft Dia. d 1 Corresponding Bearing Numbers H HE,HS,HA H H HE,HS HE,HS L L D 1 D 1 S S Self-Aligning Spherical HA HA Ball Roller mm in. mm in. mm in. mm in. mm in. Bearings Bearings H304 17 0.669 28 1.102 32 1.260 7 0.276 2204K 1304K 21304K H305 HE305 20 0.787 19.050 3/4 29 1.142 38 1.496 8 0.315 2205K 1305K 22205K 21305K H306 HS306 22.225 7/8 HA306 23.812 15/16 HE306 25 0.984 25.400 1 31 1.220 45 1.772 8 0.315 2206K 1306K 22206K 21306K H307 HS307 30 1.181 28.575 1-1/8 35 1.378 52 2.047 9 0.354 2207K 1307K 22207K 21307K HA307 30.162 1-3/16 H308 HE308 35 1.378 31.750 1-1/4 36 1.417 58 2.283 10 0.394 2208K 1308K 22208K 21308K HA308 33.338 1-5/16 HS308 34.925 1-3/8 H309 HA309 36.512 1-7/16 HE309 40 1.575 38.100 1-1/2 39 1.535 65 2.559 11 0.433 2209K 1309K 22209K 21309K HS309 41.275 1-5/8 H310 HS310 41.275 1-5/8 HA310 42.862 1-11/16 HE310 45 1.772 44.450 1-3/4 42 1.654 70 2.756 12 0.472 2210K 1310K 22210K 21310K H311 HS311 47.625 1-7/8 HA311 49.212 1-15/16 HE311X 3) 50 1.969 50.800 2 45 1.772 75 2.953 12 0.472 2211K 1311K 22211K 21311K H312 HS312 55 2.165 53.975 2-1/8 47 1.850 80 3.150 13 0.512 2212K 1312K 22212K 21312K H313 HA313 55.562 2-3/16 HE313 60 2.362 57.150 2-1/4 50 1.969 85 3.346 14 0.551 2213K 1313K 22213K 21313K HS313 60.325 2-3/8 H314 60 2.362 52 2.047 92 3.622 14 0.551 22214K 21314K H315 HA315 61.912 2-7/16 HE315 65 2.559 63.500 2-1/2 55 2.165 98 3.858 15 0.591 2215K 1315K 22215K 21315K H316 HA316 68.262 2-11/16 HE316 70 2.756 69.850 2-3/4 59 2.323 105 4.134 17 0.669 2216K 1316K 22216K 21316K H317 HA317 74.612 2-15/16 HE317 75 2.953 76.200 3 63 2.480 110 4.331 18 0.709 2217K 1317K 22217K 21317K H318 HE318 80 3.150 82.550 3-1/4 65 2.559 120 4.724 18 0.709 2218K 1318K 22218K 21318K H319 HE319 85 3.346 82.550 3-1/4 68 2.677 125 4.921 19 0.748 2219K 1319K 22219K 21319K H320 HE320 90 3.543 88.900 3-1/2 71 2.795 130 5.118 20 0.787 2220K 1320K 22220K 21320K H322 HE322 100 3.937 101.600 4 77 3.031 145 5.709 21 0.827 2222K 1322K 22222K 21322K 1) Adapter numbers apply to adapter sleeve, lock-nut, and lock-washer assemblies. 2) The thread size of HE211 X is M55x1.5 and differs from the standard (M55x2.0). 3) The thread size of HE311 X is M55x1.5 and differs from the standard (M55x2.0). H=METRIC SHAFT 454 HE=IMPERIAL SHAFT
ACCESSORIES Adapter Sleeves Series H23, HE23, HS23,HA23 Adapter Nos. 1) Bore Shaft Dia. d 1 Bore Shaft Dia. Corresponding Bearing Numbers H HE,HS,HA H H HE,HS HE,HS L L D 1 D 1 S S S 1 S 1 Self-Align Spherical Roller HA HA Ball Brg Bearings mm in. mm in. mm in. mm in. mm in. mm in. H2304 17 0.669 31 1.220 32 1.260 7 0.276 2304K H2305 HE2305 20 0.787 19.050 3/4 35 1.378 38 1.496 8 0.315 2305K H2306 HS2306 22.225 7/8 HE2306 25 0.984 25.400 1 38 1.496 45 1.772 8 0.315 2306K H2307 HS2307 30 1.181 28.575 1-1/8 43 1.693 52 2.047 9 0.354 2307K H2308 HE2308 35 1.378 31.750 1-1/4 46 1.811 58 2.283 10 0.394 2308K 22308K HS2308 34.925 1-3/8 H2309 HA2309 36.512 1-7/16 HE2309 40 1.575 38.100 1-1/2 50 1.969 65 2.559 11 0.433 2309K 22309K H2310 HS2310 41.275 1-5/8 HA2310 42.862 1-11/16 HE2310 45 1.772 44.450 1-3/4 55 2.165 70 2.756 12 0.472 2310K 22310K H2311 HS2311 47.625 1-7/8 HA2311 49.212 1-15/16 HE2311X 2) 50 1.969 50.800 2 59 2.323 75 2.953 12 0.472 2311K 22311K H2312 HS2312 55 2.165 53.975 2-1/8 62 2.441 80 3.150 13 0.512 2312K 22312K H2313 HA2313 55.562 2-3/16 HE2313 60 2.362 57.150 2-1/4 65 2.559 85 3.346 14 0.551 2313K 22313K HS2313 60.325 2-3/8 H2314 60 2.362 68 2.677 92 3.622 14 0.551 22314K H2315 HA2315 61.912 2-7/16 HE2315 65 2.559 63.500 2-1/2 73 2.874 98 3.858 15 0.591 2315K 22315K H2316 HA2316 68.262 2-11/16 HE2316 70 2.756 69.850 2-3/4 78 3.071 105 4.134 17 0.669 2316K 22316K H2317 HA2317 74.612 2-15/16 HE2317 75 2.953 76.200 3 82 3.228 110 4.331 18 0.709 2317K 22317K H2318 HE2318 80 3.150 82.550 3-1/4 86 3.386 120 4.724 18 0.709 2318K 23218K 22318K H2319 HE2319 85 3.346 82.550 3-1/4 90 3.543 125 4.921 19 0.748 2319K 22319K H2320 HE2320 90 3.543 88.900 3-1/2 97 3.819 130 5.118 20 0.787 2320K 23220K 22320K H2322 HE2322 100 3.937 101.600 4 105 4.134 145 5.709 21 0.827 2322K 23222K 22322K H2324 HE2324 110 4.331 107.950 4-1/4 112 4.409 155 6.102 22 0.866 23224K 22324K H2326 HE2326 115 4.528 114.300 4-1/2 121 4.764 165 6.496 23 0.906 23226K 22326K H2328 HE2328 125 4.921 127.000 5 131 5.157 180 7.087 24 0.945 23228K 22328K H2330 HE2330 135 5.315 133.350 5-1/4 139 5.472 195 7.677 26 1.024 23230K 22330K H2332 HE2332 140 5.512 139.700 5-1/2 147 5.787 210 8.268 28 1.102 23232K 22332K H2334 HE2334 150 5.906 152.400 6 154 6.063 220 8.661 29 1.142 23234K 22334K H2336 HE2336 160 6.299 165.100 6-1/2 161 6.339 230 9.055 30 1.181 23236K 22336K H2338 HE2338 170 6.693 171.450 6-3/4 169 6.654 240 9.449 31 1.220 23238K 22338K H2340 HE2340 180 7.087 177.800 7 176 6.929 250 9.843 32 1.260 23240K 22340K H2344 200 7.874 183 7.205 280 11.024 32 1.260 44 1.732 23244K 22344K H2348 220 8.661 196 7.717 300 11.811 34 1.339 46 1.811 23248K 22348K H2352 240 9.449 208 8.189 330 12.992 36 1.417 49 1.929 23252K 22352K H2356 260 10.236 221 8.701 350 13.780 38 1.496 51 2.008 23256K 22356K 1) Adapter numbers apply to adapter sleeve, lock-nut, and lock-washer (or locking clamp) assemblies. 2) The thread size of HE2311 X is M55x1.5 and differs from the standard (M55x2.0). 455
ACCESSORIES Adapter Sleeves Series H30, HE30, H31, HE31, H32 Series H30 HE30 Adapter Nos. 1) Bore Shaft Dia. d 1 Bore Shaft Dia. H HE H H HE HE L L D 1 D 1 S S S 1 S 1 Spherical mm in. mm in. mm in. mm in. mm in. mm in. Roller B. H3024 HE3024 110 4.331 107.950 4-1/4 72 2.835 145 5.709 22 0.866 23024K H3026 HE3026 115 4.528 114.300 4-1/2 80 3.150 155 6.102 23 0.906 23026K H3028 HE3028 125 4.921 127.000 5 82 3.228 165 6.496 24 0.945 23028K H3030 HE3030 135 5.315 133.350 5-1/4 87 3.425 180 7.087 26 1.024 23030K H3032 HE3032 140 5.512 139.700 5-1/2 93 3.661 190 7.480 28 1.102 23032K H3034 HE3034 150 5.906 152.400 6 101 3.976 200 7.874 29 1.142 23034K H3036 HE3036 160 6.299 165.100 6-1/2 109 4.291 210 8.268 30 1.181 23036K H3038 HE3038 170 6.693 171.450 6-3/4 112 4.409 220 8.661 31 1.220 23038K H3040 HE3040 180 7.087 177.800 7 120 4.724 240 9.449 32 1.260 23040K H3044 200 7.874 128 5.039 260 10.236 30 1.181 41 1.614 23044K H3048 220 8.661 133 5.236 290 11.417 34 1.339 46 1.811 23048K H3052 240 9.449 147 5.787 310 12.205 34 1.339 46 1.811 23052K H3056 260 10.236 152 5.984 330 12.992 38 1.496 50 1.969 23056K H3060 280 11.024 168 6.614 360 14.173 42 1.654 54 2.126 23060K H3064 300 11.811 171 6.732 380 14.961 42 1.654 55 2.165 23064K 1) Adapter numbers apply to adapter sleeve, lock-nut, and lock-washer (or locking clamp) assemblies. Series H31 HE31 H32 456 Adapter Nos. 1) Bore Shaft Dia. d 1 Bore Shaft Dia. H HE H H HE HE L L D 1 D 1 S S S 1 S 1 Spherical Roller mm in. mm in. mm in. mm in. mm in. mm in. Bearings H3122 HE3122 100 3.937 101.600 4 81 3.189 145 5.709 21 0.827 23122K H3124 HE3124 110 4.331 107.950 4-1/4 88 3.465 155 6.102 22 0.866 23124K 22224K H3126 HE3126 115 4.528 114.300 4-1/2 92 3.622 165 6.496 23 0.906 23126K 22226K H3128 HE3128 125 4.921 127.000 5 97 3.819 180 7.087 24 0.945 23128K 22228K H3130 HE3130 135 5.315 133.350 5-1/4 111 4.370 195 7.677 26 1.024 23130K 22230K H3132 HE3132 140 5.512 139.700 5-1/2 119 4.685 210 8.268 28 1.102 23132K 22232K H3134 HE3134 150 5.906 152.400 6 122 4.803 220 8.661 29 1.142 23134K 22234K H3136 HE3136 160 6.299 165.100 6-1/2 131 5.157 230 9.055 30 1.181 23136K 22236K H3138 HE3138 170 6.693 171.450 6-3/4 141 5.551 240 9.449 31 1.220 23138K 22238K H3140 HE3140 180 7.087 177.800 7 150 5.906 250 9.843 32 1.260 23140K 22240K H3144 200 7.874 158 6.220 280 11.024 32 1.260 44 1.732 23144K 22244K H3148 220 8.661 169 6.654 300 11.811 34 1.339 46 1.811 23148K 22248K H3152 240 9.449 187 7.362 330 12.992 36 1.417 49 1.929 23152K 22252K H3156 260 10.236 192 7.559 350 13.780 38 1.496 51 2.008 23156K 22256K H3160 280 11.024 208 8.189 380 14.961 40 1.575 53 2.087 23160K 22260K H3164 300 11.811 226 8.898 400 15.748 42 1.654 56 2.205 23164K 22264K H3260 280 11.024 240 9.449 380 14.961 40 1.575 53 2.087 23260K H3264 300 11.811 258 10.157 400 15.748 42 1.654 56 2.205 23264K 1) Adapter numbers apply to adapter sleeve, lock-nut, and lock-washer (or locking clamp) assemblies.
ACCESSORIES Withdrawal Sleeves Series AH3, AH22 Series AH3 AH22 Withdraw. Bore Shaft Dimensions Corresponding 4) Sleeve 1) Dia. d 1 L L F F L 1 2) L 1 Thd 3) Extract Bearing Numbers No. mm in. mm in. mm in. mm in. Size D 2 Nut No. Spherical Roller B. dia x pitch mm AH308 35 1.378 29 1.142 6 0.236 32 1.260 M45x1.5 AN09 22208K 21308K AH309 40 1.575 31 1.220 6 0.236 34 1.339 M50x1.5 AN10 22209K 21309K AHX310 45 1.772 35 1.378 7 0.276 38 1.496 M55x2 AN11 22210K 21310K AHX311 50 1.969 37 1.457 7 0.276 40 1.575 M60x2 AN12 22211K 21311K AHX312 55 2.165 40 1.575 8 0.315 43 1.693 M65x2 AN13 22212K 21312K AH313 60 2.362 42 1.654 8 0.315 45 1.772 M75x2 AN15 22213K 21313K AH314 65 2.559 43 1.693 8 0.315 47 1.850 M80x2 AN16 22214K 21314K AH315 70 2.756 45 1.772 8 0.315 49 1.929 M85x2 AN17 22215K 21315K AH316 75 2.953 48 1.890 8 0.315 52 2.047 M90x2 AN18 22216K 21316K AHX317 80 3.150 52 2.047 9 0.354 56 2.205 M95x2 AN19 22217K 21317K AHX318 85 3.346 53 2.087 9 0.354 57 2.244 M100x2 AN20 22218K 21318K AHX319 90 3.543 57 2.244 10 0.394 61 2.402 M105x2 AN21 22219K 21319K AHX320 95 3.740 59 2.323 10 0.394 63 2.480 M110x2 AN22 22220K 21320K AH2236 170 6.693 105 4.134 17 0.669 110 4.331 M200x3 AN40 22236K AH2238 180 7.087 112 4.409 18 0.709 117 4.606 TM210x4 HN42 22238K AH2240 190 7.480 118 4.646 19 0.748 123 4.843 TM220x4 HN44 22240K 1) Withdrawal sleeves listed here do not include extracting nuts. Please order extracting nuts separately. 2) The dimension L1 is the overall width of the withdrawal sleeve and bearing before mounting. 3) TM indicates Metric Series 30deg Trapezoidal Screw. Series AH240 AH241 Withdraw. Bore Shaft Dimensions Corresponding 4) Sleeve 1) Dia. d 1 L L F F L 1 2) L 1 Thd 3) Extract Bearing Numbers No. mm in. mm in. mm in. mm in. Size D 2 Nut No. Spherical Roller B. dia x pitch mm AH24024 115 4.528 73 2.874 13 0.512 82 3.228 M125x2 AN25 24024K30 AH24026 125 4.921 83 3.268 14 0.551 93 3.661 M135x2 AN27 24026K30 AH24028 135 5.315 83 3.268 14 0.551 93 3.661 M145x2 AN29 24028K30 AH24030 145 5.709 90 3.543 15 0.591 101 3.976 M155x3 AN31 24030K30 AH24032 150 5.906 95 3.740 15 0.591 106 4.173 M170x3 AN34 24032K30 AH24034 160 6.299 106 4.173 16 0.630 117 4.606 M180x3 AN36 24034K30 AH24036 170 6.693 116 4.567 16 0.630 127 5.000 M190x3 AN38 24036K30 AH24038 180 7.087 118 4.646 18 0.709 131 5.157 M200x3 AN40 24038K30 AH24040 190 7.480 127 5.000 18 0.709 140 5.512 TM210x4 HN42 24040K30 AH24122 105 4.134 82 3.228 13 0.512 91 3.583 M115x2 AN23 24122K30 AH24124 115 4.528 93 3.661 13 0.512 102 4.016 M130x2 AN26 24124K30 AH24126 125 4.921 94 3.701 14 0.551 104 4.094 M140x2 AN28 24126K30 AH24128 135 5.315 99 3.898 14 0.551 109 4.291 M150x2 AN30 24128K30 AH24130 145 5.709 115 4.528 15 0.591 126 4.961 M160x3 AN32 24130K30 AH24132 150 5.906 124 4.882 15 0.591 135 5.315 M170x3 AN34 24132K30 AH24134 160 6.299 125 4.921 16 0.630 136 5.354 M180x3 AN36 24134K30 AH24136 170 6.693 134 5.276 16 0.630 145 5.709 M190x3 AN38 24136K30 AH24138 180 7.087 146 5.748 18 0.709 159 6.260 M200x3 AN40 24138K30 AH24140 190 7.480 158 6.220 18 0.709 171 6.732 TM210x4 HN42 24140K30 1) Withdrawal sleeves listedhere do not include extracting nuts. Please order extracting nuts separately. 2) The dimension L1 is the overall width of the withdrawal sleeve and bearing before mounting. 3) TM indicates Metric Series 30deg Trapezoidal Screw. Bore Diameter Number Tolerances for Withdrawal Sleeves Bore Diameter d Deviation Length L Deviation Length F Deviation mm inch mm inch mm inch 08 ~ 10 ±0.05 ±0.0020 ±0.25 ±0.010 ±0.25 ±0.010 11 ~ 16 ±0.06 ±0.0024 ±0.25 ±0.010 ±0.25 ±0.010 17 ~ 24 ±0.07 ±0.0028 ±0.25 ±0.010 ±0.25 ±0.010 26 ~ 36 ±0.08 ±0.0031 ±0.25 ±0.010 ±0.25 ±0.010 38 ~ 48 ±0.09 ±0.0035 ±0.25 ±0.010 ±0.25 ±0.010 457
ACCESSORIES Withdrawal Sleeves Series AH23, AH30, AH31, AH32 Withdraw. Bore Shaft Dimensions Corresponding 4) Sleeve 1) Dia. d 1 L L F F L 1 2) L 1 Thd 3) Extract Bearing Nos. No. mm in. mm in. mm in. mm in. Size D 2 Nut No. Spherical Roller dia x pitch mm AH2308 35 1.378 40 1.575 7 0.276 43 1.693 M45x1.5 AN09 22308K AH2309 40 1.575 44 1.732 7 0.276 47 1.850 M50x1.5 AN10 22309K AHX2310 45 1.772 50 1.969 9 0.354 53 2.087 M55x2 AN11 22310K AHX2311 50 1.969 54 2.126 10 0.394 57 2.244 M60x2 AN12 22311K AHX2312 55 2.165 58 2.283 11 0.433 61 2.402 M65x2 AN13 22312K AH2313 60 2.362 61 2.402 12 0.472 64 2.520 M75x2 AN15 22313K AHX2314 65 2.559 64 2.520 12 0.472 68 2.677 M80x2 AN16 22314K AHX2315 70 2.756 68 2.677 12 0.472 72 2.835 M85x2 AN17 22315K AHX2316 75 2.953 71 2.795 12 0.472 75 2.953 M90x2 AN18 22316K AHX2317 80 3.150 74 2.913 13 0.512 78 3.071 M95X2 AN19 22317K AHX2318 85 3.346 79 3.110 14 0.551 83 3.268 M100x2 AN20 22318K AHX2319 90 3.543 85 3.346 16 0.630 89 3.504 M105x2 AN21 22319K AHX2320 95 3.740 90 3.543 16 0.630 94 3.701 M110x2 AN22 22320K AHX2322 105 4.134 98 3.858 16 0.630 102 4.016 M125X2 AN25 22322K AHX2324 115 4.528 105 4.134 17 0.669 109 4.291 M135X2 AN27 22324K AHX2326 125 4.921 115 4.528 19 0.748 119 4.685 M145x2 AN29 22326K AHX2328 135 5.315 125 4.921 20 0.787 130 5.118 M155x3 AN31 22328K AHX2330 145 5.709 135 5.315 24 0.945 140 5.512 M165X3 AN33 22330K AH2332 150 5.906 140 5.512 24 0.945 146 5.748 M180x3 AN36 22332K AH2334 160 6.299 146 5.748 24 0.945 152 5.984 M190x3 AN38 22334K AH2336 170 6.693 154 6.063 26 1.024 160 6.299 M200x3 AN40 22336K AH2338 180 7.087 160 6.299 26 1.024 167 6.575 TM210x4 HN42 22338K AH2340 190 7.480 170 6.693 30 1.181 177 6.969 TM220x4 HN44 22340K Series AH23 1) Withdrawal sleeves listed here do not include extracting nuts. Please order extracting nuts separately. 2) The dimension L1 is the overall width of the withdrawal sleeve and bearing before mounting. 3) TM indicates Metric Series 30deg Trapezoidal Screw Threads. Withdraw. Bore Shaft Dimensions Corresponding 4) Sleeve 1) Dia. d 1 L L F F L 1 2) L 1 Thd 3) Extract Bearing Numbers No. mm in. mm in. mm in. mm in. Size D 2 Nut No. Spherical Roller B. dia x pitch mm AHX3024 115 4.528 60 2.362 13 0.512 64 2.520 M130x2 AN26 23024K AHX3026 125 4.921 67 2.638 14 0.551 71 2.795 M140x2 AN28 23026K AHX3028 135 5.315 68 2.677 14 0.551 73 2.874 M150x2 AN30 23028K AHX3030 145 5.709 72 2.835 15 0.591 77 3.031 M160x3 AN32 23030K AH3032 150 5.906 77 3.031 16 0.630 82 3.228 M170x3 AN34 23032K AH3034 160 6.299 85 3.346 17 0.669 90 3.543 M180x3 AN36 23034K AH3036 170 6.693 92 3.622 17 0.669 98 3.858 M190x3 AN38 23036K AH3038 180 7.087 96 3.780 18 0.709 102 4.016 TM205x4 HNL41 23038K AH3040 190 7.480 102 4.016 19 0.748 108 4.252 TM215x4 HNL43 23040K AHX3122 105 4.134 68 2.677 11 0.433 72 2.835 M120x2 AN24 23122K 22222K AHX3124 115 4.528 75 2.953 12 0.472 79 3.110 M130x2 AN26 23124K 22224K AHX3126 125 4.921 78 3.071 12 0.472 82 3.228 M140x2 AN28 23126K 22226K AHX3128 135 5.315 83 3.268 14 0.551 88 3.465 M150x2 AN30 23128K 22228K AHX3130 145 5.709 96 3.780 15 0.591 101 3.976 M165x3 AN33 23130K 22230K AH3132 150 5.906 103 4.055 16 0.630 108 4.252 M180x3 AN36 23132K 22232K AH3134 160 6.299 104 4.094 16 0.630 109 4.291 M190x3 AN38 23134K 22234K AH3136 170 6.693 116 4.567 19 0.748 122 4.803 M200x3 AN40 23136K AH3138 180 7.087 125 4.921 20 0.787 131 5.157 TM210x4 HN42 23138K AH3140 190 7.480 134 5.276 21 0.827 140 5.512 TM220x4 HN44 23140K AHX3222 105 4.134 82 3.228 11 0.433 86 3.386 M125x2 AN25 23222K AHX3224 115 4.528 90 3.543 13 0.512 94 3.701 M135x2 AN27 23224K AHX3226 125 4.921 98 3.858 15 0.591 102 4.016 M145x2 AN29 23226K AHX3228 135 5.315 104 4.094 15 0.591 109 4.291 M155x3 AN31 23228K AHX3230 145 5.709 114 4.488 17 0.669 119 4.685 M165x3 AN33 23230K AH3232 150 5.906 124 4.882 20 0.787 130 5.118 M180x3 AN36 23232K AH3234 160 6.299 134 5.276 24 0.945 140 5.512 M190x3 AN38 23234K AH3236 170 6.693 140 5.512 24 0.945 146 5.748 M200x3 AN40 23236K AH3238 180 7.087 145 5.709 25 0.984 152 5.984 TM210x4 HN42 23238K AH3240 190 7.480 153 6.024 25 0.984 160 6.299 TM220x4 HN44 23240K Series AH30 AH31 AH32 1) Withdrawal sleeves listed here do not include extracting nuts. Please order extracting nuts separately. 2) The dimension L1 is the overall width of the withdrawal sleeve and bearing before mounting. 3) TM indicates Metric Series 30deg Trapezoidal Screw Thread. 458
ACCESSORIES Lock Nuts Series AN For Adapters, Shafts, and Withdrawal Sleeves Lock-nut for use with Lock-washer Lock Dimensions Related Numbers Nut Thd. Size Bore Dia. Lock Shaft Dia. Withdrawal Sleeve Numbers No. D 1 (mm) D 3 D 3 B n B n Code No. Washer mm in. AH 30 AH31 AH22 AH32 AH3 AH23 dia x pitch mm in. mm in. Adapter No. Sleeve AN02 M15x1 25 0.984 5 0.197 AW02 15 0.591 AN03 M17x1 28 1.102 5 0.197 AW03 17 0.669 AN04 M20x1 32 1.260 6 0.236 04 AW04 20 0.787 AN05 M25x1.5 38 1.496 7 0.276 05 AW05 25 0.984 AN06 M30x1.5 45 1.772 7 0.276 06 AW06 30 1.181 AN07 M35x1.5 52 2.047 8 0.315 07 AW07 35 1.378 AN08 M40x1.5 58 2.283 9 0.354 08 AW08 40 1.575 AN09 M45x1.5 65 2.559 10 0.394 09 AW09 45 1.772 AH308 AH2308 AN10 M50x1.5 70 2.756 11 0.433 10 AW10 50 1.969 AH309 AH2309 AN11 M55x2 75 2.953 11 0.433 11 AW11 55 2.165 AHX310 AHX2310 AN12 M60x2 80 3.150 11 0.433 12 AW12 60 2.362 AHX311 AHX2311 AN13 M65x2 85 3.346 12 0.472 13 AW13 65 2.559 AHX312 AHX2312 AN14 M70x2 92 3.622 12 0.472 14 AW14 70 2.756 AN15 M75x2 98 3.858 13 0.512 15 AW15 75 2.953 AH313 AH2313 AN16 M80x2 105 4.134 15 0.591 16 AW16 80 3.150 AH314 AHX2314 AN17 M85x2 110 4.331 16 0.630 17 AW17 85 3.346 AH315 AHX2315 AN18 M90x2 120 4.724 16 0.630 18 AW18 90 3.543 AH316 AHX2316 AN19 M95x2 125 4.921 17 0.669 19 AW19 95 3.740 AHX317 AHX2317 AN20 M100x2 130 5.118 18 0.709 20 AW20 100 3.937 AHX3218 AHX318 AHX2318 AN21 M105x2 140 5.512 18 0.709 21 AW21 105 4.134 AHX319 AHX2319 AN22 M110x2 145 5.709 19 0.748 22 AW22 110 4.331 AHX3220 AHX320 AHX2320 AN23 M115x2 150 5.906 19 0.748 AW23 115 4.528 AHX321 AN24 M120x2 155 6.102 20 0.787 24 AW24 120 4.724 AHX3122 AHX322 AN25 M125x2 160 6.299 21 0.827 AW25 125 4.921 AHX3222 AHX2322 AN26 M130x2 165 6.496 21 0.827 26 AW26 130 5.118 AHX3024 AHX3124 AHX324 AN27 M135x2 175 6.890 22 0.866 AW27 135 5.315 AHX3224 AHX2324 AN28 M140x2 180 7.087 22 0.866 28 AW28 140 5.512 AHX3026 AHX3126 AHX326 AN29 M145x2 190 7.480 24 0.945 AW29 145 5.709 AHX3226 AHX2326 AN30 M150x2 195 7.677 24 0.945 30 AW30 150 5.906 AHX3028 AHX3128 AHX328 AN31 M155x3 200 7.874 25 0.984 AHX3228 AHX2328 AN32 M160x3 210 8.268 25 0.984 32 AW32 160 6.299 AHX3030 AN33 M165X3 210 8.268 26 1.024 AHX3130 AHX3230 AHX330 AHX2330 AN34 M170x3 220 8.661 26 1.024 34 AW34 170 6.693 AH3032 AN36 M180x3 230 9.055 27 1.063 36 AW36 180 7.087 AH3034 AH3132 AH3232 AH332 AH2332 AN38 M190x3 240 9.449 28 1.102 38 AW38 190 7.480 AH3036 AH3134 AH3234 AH334 AH2334 AN40 M200x3 250 9.843 29 1.142 40 AW40 200 7.874 AH3136 AH2236 AH3236 AH2336 459
ACCESSORIES Lock Washers Series AW With Bent Inner Tab With Straight Inner Tab Lock Washer Nos. Dimensions Related Nos. W/ Bent W/ Straight D 1 D 1 E E t t D s D s Bore Dia. Lock Inner Tab Inner Tab mm in. mm in. mm in. mm in. Code No. Nut Adaptor No. Sleeve AW02 AW02X 15 0.591 4 0.157 1 0.039 28 1.102 AN02 AW03 AW03X 17 0.669 4 0.157 1 0.039 32 1.260 AN03 AW04 AW04X 20 0.787 4 0.157 1 0.039 36 1.417 04 AN04 AW05 AW05X 25 0.984 5 0.197 1.2 0.047 42 1.654 05 AN05 AW06 AW06X 30 1.181 5 0.197 1.2 0.047 49 1.929 06 AN06 AW07 AW07X 35 1.378 6 0.236 1.2 0.047 57 2.244 07 AN07 AW08 AW08X 40 1.575 6 0.236 1.2 0.047 62 2.441 08 AN08 AW09 AW09X 45 1.772 6 0.236 1.2 0.047 69 2.717 09 AN09 AW10 AW10X 50 1.969 6 0.236 1.2 0.047 74 2.913 10 AN10 AW11 AW11X 55 2.165 8 0.315 1.2 0.047 81 3.189 11 AN11 AW12 AW12X 60 2.362 8 0.315 1.5 0.059 86 3.386 12 AN12 AW13 AW13X 65 2.559 8 0.315 1.5 0.059 92 3.622 13 AN13 AW14 AW14X 70 2.756 8 0.315 1.5 0.059 98 3.858 14 AN14 AW15 AW15X 75 2.953 8 0.315 1.5 0.059 104 4.094 15 AN15 AW16 AW16X 80 3.150 10 0.394 1.8 0.071 112 4.409 16 AN16 AW17 AW17X 85 3.346 10 0.394 1.8 0.071 119 4.685 17 AN17 AW18 AW18X 90 3.543 10 0.394 1.8 0.071 126 4.961 18 AN18 AW19 AW19X 95 3.740 10 0.394 1.8 0.071 133 5.236 19 AN19 AW20 AW20X 100 3.937 12 0.472 1.8 0.071 142 5.591 20 AN20 AW21 AW21X 105 4.134 12 0.472 1.8 0.071 145 5.709 21 AN21 AW22 AW22X 110 4.331 12 0.472 1.8 0.071 154 6.063 22 AN22 AW23 AW23X 115 4.528 12 0.472 2 0.079 159 6.260 AN23 AW24 AW24X 120 4.724 14 0.551 2 0.079 164 6.457 24 AN24 AW25 AW25X 125 4.921 14 0.551 2 0.079 170 6.693 AN25 AW26 AW26X 130 5.118 14 0.551 2 0.079 175 6.890 26 AN26 AW27 AW27X 135 5.315 14 0.551 2 0.079 185 7.283 AN27 AW28 AW28X 140 5.512 16 0.630 2 0.079 192 7.559 28 AN28 AW29 AW29X 145 5.709 16 0.630 2 0.079 202 7.953 AN29 AW30 AW30X 150 5.906 16 0.630 2 0.079 205 8.071 30 AN30 AW31 AW31X 155 6.102 16 0.630 2.5 0.098 212 8.346 AN31 AW32 AW32X 160 6.299 18 0.709 2.5 0.098 217 8.543 32 AN32 AW33 AW33X 165 6.496 18 0.709 2.5 0.098 222 8.740 AN33 AW34 AW34X 170 6.693 18 0.709 2.5 0.098 232 9.134 34 AN34 AW36 AW36X 180 7.087 20 0.787 2.5 0.098 242 9.528 36 AN36 AW38 AW38X 190 7.480 20 0.787 2.5 0.098 252 9.921 38 AN38 AW40 AW40X 200 7.874 20 0.787 2.5 0.098 262 10.315 40 AN40 460
MONITORS Induction heaters are a preferred and much safer method of heating a bearing than using a flame or oil bath. Bearing heaters produce strong alternating magnetic fields that induce eddy currents in the metals. The currents cause rapid and efficient heating for the component and the low voltage output eliminates any hazards due to shocks or sparks. Bearing Heaters NSK Induction Heaters Bearing heaters from NSK are a fast, safe and efficient way to mount straight bore bearings onto shafts. They provide uniform inner race heating that helps to reduce bearing mounting, time and cost. With automatic temperature and demagnetizing control features, a light and compact design, and the versatility to heat many different bearing sizes and types of components, NSK bearing heaters are a must have for maintenance professionals. CAPACITY (KVA) MAXIMUM CURRENT A = 10A B = 15A CHE 01 10 A -E NSK BEARING HEATER VOLTAGE 10: 100V 12: 120V 20: 200V 22: 220V ENGLISH- LANGUAGE MODEL CHE 02 10-50 E CAPACITY (KVA) FREQUENCY 50: 50 Hz 60: 60 Hz 467