INDUSTRIAL STRENGTH work light range
Purpose built to survive the harshest, toughest conditions on earth. The Hammerheads Industrial Strength Work Light Range was born from a culmination of the experience and intellectual property gathered through the notable history of OEX work lights servicing the extreme environment of the Australian mining industry. Integral to the development of this well thought out, well constructed range is that it has been designed from the ground up in contrast to simply adapting an existing light to suit the application. The Hammerheads Industrial Strength Work Light Range is a high quality, functional range designed to change the landscape of quality industrial lighting forever!
Features & Benefits Revolutionary Protrac 360 Aiming System Hammerheads can be adjusted before fitment using the plate and rotation angles on the revolutionary Protrac bracket. A fit out library is also available to suit common mining equipment with known locations and angles for the optimum beam pattern. Electronic Thermal Management In an extraordinary situation where the light is subjected to massive heat overload, a self protection protocol is engaged to reduce the light output, until such time as the heat overload retreats to normal parameters. Beam Pattern Identification Using a clever coloured disc system, each beam pattern is linked to a different disc colour. This ensures beam patterns are easily distinguished for identification and eventual end of life replacement. Soft Start Technology Low in rush current on start up reduces wear on associated components which is particularly important on machines where multiple lights are used. It avoids light misfires and eases load on existing wiring. This feature helps reduce costly downtime. Note: Soft start is not incorporated in 2 LED versions as in rush current is determined to be too small to benefit from this attribute. Reverse Polarity Operation Hammerheads will operate even when the polarity to the light is reversed. This is an advantage when retro-fitting Hammerheads to equipment that has previously been fitted with different work lights. This reduces the installation times for the technicians on site, therefore further reducing costs. It also prevents accidental damage caused by incorrect installation. Gold DT Connectors Any product is only as good as its components and Hammerheads Deutsch Gold Pin DT Connectors are designed specifically for harsh environmental conditions, where even a small degradation in connection may be critical to the performance of the work lights. The gold pins will help provide the reliability and performance that the Hammerheads brand requires. Dielectric grease is also provided with each Hammerhead to assure brilliant electrical connection is attained.
Outstanding Light Output The latest Cree XM-L2 10 watt LEDs provide a mass volume of light where you need it most. The colour tempreature of LED is closer to that of sunlight which reduces eye strain and enables excellent peripheral vision. Rated to IP69K The IP69K rating ensures that the work lights are dust tight with no ingress of dust and protected against high pressure, high temperature wash downs. The IP69K rating is the highest protection available. Ideal for water cannon wash downs. Fully Suspended Shock Dampening System With the revolutionary Protrac 360 suspended mounting system the Hammerheads can withstand vibration up to 60G. Long Life - 50,000 Hours Hammerheads light output is warranted for 50,000 hours or 6 years. (excluding physical or environmental damage). Using Pulse Width Modulation (PWM), the LEDs are being turned on and off at a frequency quicker than the human eye can detect. This technology allows the LEDs to be driven hard whilst still achieving long life span. Environmental Non-Stick Coating The Hammerheads Industrial Strength Work Light Range boasts an Interpon 810 coating which imparts a low-friction, wear resistant surface to the lights, enabling them to remain unaffected by chemical environments. Very few solid substances will permanently adhere to an Interpon 810 finish and, in many cases, surfaces are self-cleaning.
Every Light, every beam, every situation. All work lights are available in a number of beam patterns including Spot, Flood, Wide Flood and Elliptical. Custom beam configurations are also available upon request. Universal Specifications Colour Temp: 6,000 Kelvin Input Voltage: 11-65VDC LED Type: Cree XM-L2 Wattage per LED: 10W IP Rating: IP69K Dust Proof & Water Submersible: 3m / 9.8ft Vibration Dampened & Shock Proof: Up to 60G EMC / EMI Rating: CISPR 25 - Class 3 Connector: DT04-2P with Gold Pins Lens: Polycarbonate Environmental Coating: Interpon 810 Bracket Material: m 304 Stainless Steel Bolt Hole Size: M10 - M12
Easy Coloured Disc Identifier - Beam Patterns The entire Hammerheads range utilise a clever coloured disc system which quickly identifies the beam pattern of the light. For example the yellow discs indicate the light has a Flood beam pattern, whilst the red discs indicate the light uses a Spot beam pattern. This attribute is highly useful when the time comes to replace the light, as the visual cue of the colour allows the correct beam pattern to be identified without having to remove the light first to identify its beam pattern. Spot Beam The pattern and high volume of light output makes the focused beam ideal where precise illumination and light control is critical. Flood Beam The pattern boasts greater spread around the light and reduced intensity at the outer limits. Ideal when requiring a large volume of light spread around a work site or vehicle. Wide Flood Beam The pattern boasts an even greater spread around the light and reduced intensity at the outer limits. Ideal when requiring a wider volume of light illuminating a work site or warehouse. Elliptical Beam The pattern produces an oval beam pattern with a wider amount of light covering a medium distance. Ideal for when more penetration is required from the light. Great for applications that don t require much upward or downward light. Custom Beam Whilst spot, flood, wide flood and elliptical beam patterns will suit most applications, there are certain applications that may require a custom beam pattern. Contact your local Hammerheads distributor for more information on how we can tailor our Hammerheads to suit your individual requirements.
2 LED INDUSTRIAL STRENGTH work light
Specifications Available Beam Patterns Raw Lumens: 1,840 3 Effective Lumens: 1,198 Current Draw: 0.76 Amps @ 24V DC 20W (10W per LED) Spot Beam Part No. HHL100210 - -3 6 12 18 24 1kg / 2.20lb M10 Flood Beam Part No. HHL100240 3 - -3 6 12 18 24 3 Wide Flood Beam Part No. HHL100260 - -3 6 12 18 24 124.7mm / 4.90in 3 Elliptical Beam Part No. HHL10023060-86mm / 3.38in 87mm 3.43in Custom Beam -3 6 12 18 24 Customise your own beam pattern to suit your needs
4 LED INDUSTRIAL STRENGTH work light
Specifications Available Beam Patterns Raw Lumens: 3,680 3 Effective Lumens: 2,679 Current Draw: 1.67 Amps @ 24V DC 40W (10W per LED) Spot Beam Part No. HHL100410 - -3 6 12 18 24 2.2kg / 4.85lb M10 Flood Beam Part No. HHL100440 3 - -3 6 12 18 24 3 Wide Flood Beam Part No. HHL100460 - -3 6 12 18 24 135.8mm / 5.34in Elliptical Beam Part No. HHL10043060 3 - -3 6 12 18 24 132mm 5.20in Custom Beam Customise your own beam pattern to suit your needs 101mm / 3.98in
6 LED INDUSTRIAL STRENGTH work light
Specifications Available Beam Patterns Raw Lumens: 5,521 3 Effective Lumens: 3,909 Current Draw: 2.47 Amps @ 24V DC 60W (10W per LED) Spot Beam Part No. HHL100610 - -3 7 14 21 28 2.7kg / 5.95lb M10 Flood Beam Part No. HHL100640 3 - -3 7 14 21 28 3 Wide Flood Beam Part No. HHL100660 - -3 7 14 21 28 17m / 6.88in 3 Elliptical Beam Part No. HHL10063060-132mm 5.20in Custom Beam -3 7 14 21 28 Customise your own beam pattern to suit your needs 101mm / 3.98in
9 LED INDUSTRIAL STRENGTH work light
Specifications Available Beam Patterns Raw Lumens: 8,281 6 3 Effective Lumens: 5,849 Current Draw: 3.74 Amps @ 24V DC 90W (10W per LED) Spot Beam Part No. HHL100910 1-1 -3-6 8 16 24 32 4.4kg / 9.70lb M10 Flood Beam Part No. HHL100940 6 3 1-1 -3-6 8 16 24 32 6 3 Wide Flood Beam Part No. HHL100960 1-1 -3-6 8 16 24 32 6 17m / 6.88in Elliptical Beam Part No. HHL10093060 3 1-1 -3-6 8 16 24 32 173mm 6.81in Custom Beam Customise your own beam pattern to suit your needs 12m / 4.92in
16 LED INDUSTRIAL STRENGTH work light
Specifications Available Beam Patterns Raw Lumens: 14,723 Effective Lumens: 10,053 Current Draw: 6.19 Amps @ 24V DC 160W (10W per LED) 6kg / 13.23lb M12 Spot Beam Part No. HHL101610 Flood Beam Part No. HHL101640 10 7 2-2 -7-10 10 7 2-2 -7 18 36 54 72-10 18 36 54 72 10 383mm / 15.07in Wide Flood Beam Part No. HHL101660 7 2-2 -7-10 18 36 54 72 138mm 5.43in Elliptical Beam Part No. HHL10163060 10 7 2-2 -7-10 18 36 54 72 122mm / 4.80in a b c d e Custom Beam Customise your own beam pattern to suit your needs a: 91mm / 3.58in, b: 5m / 2.16in, c: 38mm / 1.49in d: 7m / 2.75in, e: / 1.96in
32 LED INDUSTRIAL STRENGTH work light
Specifications Available Beam Patterns Raw Lumens: 29,446 7 4 Effective Lumens: 19,458 Current Draw: 12.53 Amps @ 24V DC 320W (10W per LED) Spot Beam Part No. HHL103210-4 -7 12 24 36 48 11kg / 24.25lb M12 Flood Beam Part No. HHL103240 7 4-4 -7 12 24 36 48 7 4 Wide Flood Beam Part No. HHL103260-4 386mm / 15.19in -7 12 24 36 48 7 23m 9.06in b c d Elliptical Beam Part No. HHL10323060 4-4 -7 12 24 36 48 164mm 6.46in e a Custom Beam Customise your own beam pattern to suit your needs a: 13m / 5.31in, b:76mm / 2.99in, c: 84mm / 3.30in d: 7m / 2.75in, e: / 1.96in
FITOUT example caterpillar 793 Dump Truck 1 2 14 17 3 9 4 9 13 5 6 7 8 13 12 10 11 Fitout No. Part No. Disc Colour Orientation Side Position Comments Plate Angle Rotation Angle 1 HHL100640 FLOOD Forward facing Right side outer Above wheels Forward facing, Above right wheel 0-10 2 HHL100610 SPOT Forward facing Right side inner Above wheels Forward facing, Above right wheel 5-10 3 HHL100610 SPOT Forward facing Left side inner Above wheels Forward facing, Above left wheel 5-10 4 HHL100640 FLOOD Forward facing Left side outer Above wheels Forward facing, Above left wheel 0-10 5 HHL100640 FLOOD Forward facing Right side outer OEM front bar position Front facing, Right side of front bumper 0-10 6 HHL100610 SPOT Forward facing Right side inner OEM front bar position Front facing, Right side of front bumper 5-10 7 HHL100610 SPOT Forward facing Left side inner OEM front bar position Front facing, Left side of front bumper 5-10 8 HHL100640 FLOOD Forward facing Left side outer OEM front bar position Front facing, Left side of front bumper 0-10 9 HHL100640 FLOOD Forward facing Left side Below operator cabin Forward facing, below operators platform 50-35 10 HHL100610 SPOT Rear facing Right side Below rear lift cylinder Rear facing inward, below rear cylinder 35-5 11 HHL100610 SPOT Rear facing Left side Below rear lift cylinder Rear facing inward, below rear cylinder 35-5 12 HHL100640 FLOOD Rear facing Right side Below operator cabin Rear facing, below operator platform 50-15 13 HHL100640 FLOOD Rear facing Left side Below operator cabin Rear facing, below operator platform 50-15 14 HHL100240 FLOOD n/a n/a Facing towards ladder access Access lighting ladder rail - - 15 HHL100240 FLOOD n/a n/a Facing towards ladder access Access lighting ladder rail - - 16 HHL100240 FLOOD n/a n/a Facing towards ladder access Access lighting ladder rail - - 17 HHL100240 FLOOD n/a n/a As required Engine compartment - -
Specifications - HHL100240 Specifications - HHL100610 Beam Pattern: Flood Beam Beam Pattern: Spot Beam Raw Lumens: 1,840 Raw Lumens: 5,521 Effective Lumens: 1,198 Effective Lumens: 3,909 Current Draw: 0.76 Amps @ 24V DC Current Draw: 2.47 Amps @ 24V DC Colour Temp: 6,000 Kelvin Colour Temp: 6,000 Kelvin Input Voltage: LED Type: 11-65V DC Cree XM-L2 124.7mm / 4.90in Input Voltage: LED Type: 11-65V DC Cree XM-L2 17m / 6.88in 20W (10W per LED) 60W (10W per LED) 1kg / 2.20lb 2.7kg / 5.95lb IP Rating: Vibration Tested: IP69K Up to 60G EMC / EMI Rating: CISPR 25 - Class 3 Connector: DT04-2P with Gold Pins 87mm 3.43in IP Rating: Vibration Tested: IP69K Up to 60G EMC / EMI Rating: CISPR 25 - Class 3 Connector: DT04-2P with Gold Pins 132mm 5.20in Lens: Polycarbonate Environmental Coating: Interpon 810 Bracket Material: m 304 Stainless Steel 86mm 3.98in Lens: Polycarbonate Environmental Coating: Interpon 810 Bracket Material: m 304 Stainless Steel M10 M10 101mm / 3.98in 3 3 - - -3 6 12 18 24-3 7 14 21 28 Specifications - HHL100640 Beam Pattern: Flood Beam Raw Lumens: 5,521 Effective Lumens: 3,909 Current Draw: 2.47 Amps @ 24V DC Colour Temp: 6,000 Kelvin Input Voltage: 11-65V DC LED Type: Cree XM-L2 60W (10W per LED) 2.7kg / 5.95lb IP Rating: IP69K Vibration Tested: Up to 60G EMC / EMI Rating: CISPR 25 - Class 3 Connector: DT04-2P with Gold Pins Lens: Polycarbonate Environmental Coating: Interpon 810 Bracket Material: m 304 Stainless Steel M10 3 - -3 17m / 6.88in 7 14 21 28 101mm / 3.98in 132mm 5.20in
FITOUT example caterpillar d10 dozer 7 5 1-4 13 14 11 8 7 10 9 Fitout No. Part No. Disc Colour Orientation Side Position Comments Plate Angle Rotation Angle 1 HHL100440 FLOOD Forward facing Right side outer Above lift cylinder Right lift cylinder, right position 0-10 2 HHL100410 SPOT Forward facing Right side inner Above lift cylinder Right lift cylinder, Left position 0-10 3 HHL100410 SPOT Forward facing Left side inner Above lift cylinder Left lift cylinder, right position 0-10 4 HHL100440 FLOOD Forward facing Left side outer Above lift cylinder Left lift cylinder, Left position 0-10 5 HHL100640 FLOOD Forward facing Right side Above operator cabin Cabin roof, forward facing right 45-15 6 HHL100640 FLOOD Forward facing Left side Above operator cabin Cabin roof, forward facing left 45-15 7 HHL100640 FLOOD Rear facing Right side Rear of operator cabin Cabin roof, rear facing right 45-15 8 HHL100640 FLOOD Rear facing Left side Rear of operator cabin Cabin roof, rear facing left 45-15 9 HHL100440 FLOOD Rear facing Right side Rear ripper Ripper rear facing right 0-30 10 HHL100440 FLOOD Rear facing Left side Rear ripper Ripper rear facing left 0-30 11 HHL100410 SPOT Right facing Right side Facing side of blade Cabin platform forward facing right side of blade 35-30 12 HHL100410 SPOT Left facing Left side Facing side of blade Cabin platform forward facing left side of blade 35-30 13 HHL100240 FLOOD Left facing n/a Facing towards ladder access Cabin access lighting - - 14 HHL100240 FLOOD n/a n/a As required Engine compartment - -
Specifications - HHL100240 Specifications - HHL100410 Beam Pattern: Flood Beam Beam Pattern: Spot Beam Raw Lumens: 1,840 Raw Lumens: 3,680 Effective Lumens: 1,198 Effective Lumens: 2,679 Current Draw: 0.76 Amps @ 24V DC Current Draw: 1.67 Amps @ 24V DC Colour Temp: 6,000 Kelvin Colour Temp: 6,000 Kelvin Input Voltage: LED Type: 11-65V DC Cree XM-L2 124.7mm / 4.90in Input Voltage: LED Type: 11-65V DC Cree XM-L2 135.8mm / 5.34in 20W (10W per LED) 40W (10W per LED) 1kg / 2.20lb 2.2kg / 4.85lb IP Rating: Vibration Tested: IP69K Up to 60G EMC / EMI Rating: CISPR 25 - Class 3 Connector: DT04-2P with Gold Pins 87mm 3.43in IP Rating: IP69K Vibration Tested: Up to 60G EMC / EMI Rating: CISPR 25 - Class 3 Connector: DT04-2P with Gold Pins 132mm 5.20in Lens: Polycarbonate Environmental Coating: Interpon 810 Bracket Material: m 304 Stainless Steel M10 86mm 3.98in Lens: Polycarbonate Environmental Coating: Interpon 810 Bracket Material: m 304 Stainless Steel M10 101mm / 3.98in 3 3 - - -3 6 12 18 24-3 6 12 18 24 Specifications - HHL100440 Specifications - HHL100640 Beam Pattern: Flood Beam Beam Pattern: Flood Beam Raw Lumens: 3,680 Raw Lumens: 5,521 Effective Lumens: 2,679 Effective Lumens: 3,909 Current Draw: 1.67 Amps @ 24V DC Current Draw: 2.47 Amps @ 24V DC Colour Temp: 6,000 Kelvin Colour Temp: 6,000 Kelvin Input Voltage: LED Type: 11-65V DC Cree XM-L2 135.8mm / 5.34in Input Voltage: LED Type: 11-65V DC Cree XM-L2 17m / 6.88in 40W (10W per LED) 60W (10W per LED) 2.2kg / 4.85lb 2.7kg / 5.95lb IP Rating: IP69K IP Rating: IP69K Vibration Tested: Up to 60G EMC / EMI Rating: CISPR 25 - Class 3 Connector: DT04-2P with Gold Pins 132mm 5.20in Vibration Tested: Up to 60G EMC / EMI Rating: CISPR 25 - Class 3 Connector: DT04-2P with Gold Pins 132mm 5.20in Lens: Polycarbonate Lens: Polycarbonate Environmental Coating: Interpon 810 Environmental Coating: Interpon 810 Bracket Material: m 304 Stainless Steel M10 101mm / 3.98in Bracket Material: m 304 Stainless Steel M10 101mm / 3.98in 3 3 - - -3 6 12 18 24-3 7 14 21 28
For more information on Hammerheads visit: hammerheads.com.au or hammerheads.net.nz HEAD OFFICE 5 Viola Place, Export Park Brisbane Airport QLD 4007 P: 07 3358 9400 QUEENSLAND Archerfield Unit 2, 124 Beatty Road Archerfield 4108 P: 07 3277 8633 archerfield@ashdown-ingram.com.au Bundaberg Unit 16, 96 Mount Perry Rd, North Bundaberg 4670 P: 07 4152 1063 bundaberg@ashdown-ingram.com.au Burleigh Unit 3, 2 John Duncan Court Burleigh Heads 4220 P: 07 5522 1377 burleigh@ashdown-ingram.com.au Caboolture Unit 2, 84-86 Learjet Drive Caboolture 4510 P: 07 5495 1311 caboolture@ashdown-ingram.com.au Cairns 102 Lyons Street Cairns 4870 P: 07 4031 3816 cairns@ashdown-ingram.com.au Emerald 55 Industrial Drive Emerald 4720 P: 07 4987 4388 emerald@ashdown-ingram.com.au Gladstone 116 Hanson Road Gladstone 4680 P: 07 4972 1677 gladstone@ashdown-ingram.com.au Ipswich Unit 3B, 2 Pound St West Ipswich 4305 P: 07 3202 1309 ipswich@ashdown-ingram.com.au Mackay 8 Platinum Court Mackay 4740 P: 07 4952 3172 mackay@ashdown-ingram.com.au Molendinar Unit 5, Geary Crescent Molendinar 4214 P: 07 5528 1266 molendinar@ashdown-ingram.com.au Mt Isa 15 Isa Street Mt Isa 4825 P: 07 4743 1633 mtisa@ashdown-ingram.com.au Rockhampton 223 Denison Street Rockhampton 4700 P: 07 4921 3799 rockhampton@ashdown-ingram.com.au Springwood 44 Parramatta Road Underwood 4119 P: 07 3208 4244 springwood@ashdown-ingram.com.au Sunshine Coast Unit 3, 18 Technology Drive Warana 4575 P: 07 5493 9022 sunshinecoast@ashdown-ingram.com.au Toowoomba Unit 2, 101 Mort Street Toowoomba 4350 P: 07 4632 9384 toowoomba@ashdown-ingram.com.au Townsville 502-508 Woolcock Street Townsville 4814 P: 07 4728 6222 townsville@ashdown-ingram.com.au Virginia 2095 Sandgate Road (Off Radley Street) Virginia 4014 P: 07 3633 0309 virginia@ashdown-ingram.com.au WESTERN AUSTRALIA Bunbury 8 Smokebush Drive Bunbury 6230 P: 08 9725 6734 bunbury@ashdown-ingram.com.au Geraldton 319 Place Road Webberton 6230 P: 08 9921 1338 geralton@ashdown-ingram.com.au Kalgoorlie 200 Boulder Road Kalgoorlie 6430 P: 08 9021 5211 kalgoorlie@ashdown-ingram.com.au Karratha Unit 1, Lot 991 Croydon Road Karratha 6714 P: 08 9183 8117 karratha@ashdown-ingram.com.au Kewdale 499 Abernethy Road Kewdale 6105 P: 08 9376 2544 kewdale@ashdown-ingram.com.au Osborne Park Unit 2, 3 McDonald Street Osborne Park 6017 P: 08 9444 8644 osbornepark@ashdown-ingram.com.au SOUTH AUSTRALIA Regency Park 1 Pambula Street Regency Park 5010 P: 08 8347 1637 regencypark@ashdown-ingram.com.au Thebarton 36-38 Cawthorne Street Thebarton 5031 P: 08 8257 2345 thebarton@ashdown-ingram.com.au TASMANIA Hobart 2A Pierce Street Moonah 7009 P: 03 6228 0200 hobart@ashdown-ingram.com.au Launceston 117 Galvin Street South Launceston 7249 P: 03 6344 7042 launceston@ashdown-ingram.com.au NORTHERN TERRITORY Darwin Unit 10, Winnellie Central Hickman Street Winnellie 0820 P: 08 8984 4222 darwin@ashdown-ingram.com.au NEW SOUTH WALES Albury 130 North Street Albury 2640 P: 02 6041 4443 albury@ashdown-ingram.com.au Alexandria Unit E8, 46 Maddox Street Alexandria 2015 P: 02 9516 3022 alexandria@ashdown-ingram.com.au Canberra Unit 1, 168 Gladstone Street Fyshwick 2609 P: 02 6280 6154 canberra@ashdown-ingram.com.au Coffs Harbour Unit 1, 19 Forge Drive North Boambee Valley Coffs Harbour 2450 P: 02 6652 2932 coffsharbour@ashdown-ingram.com.au Dubbo 2 McKenzie Street Dubbo 2830 P: 02 6885 2766 dubbo@ashdown-ingram.com.au Lidcombe Unit 2, 9 Parramatta Road Lidcombe 2141 P: 02 9648 1900 lidcombe@ashdown-ingram.com.au Newcastle 14 Broadmeadow Road Broadmeadow 2292 P: 02 4961 3988 newcastle@ashdown-ingram.com.au Tamworth 67 Gunnedah Road Tamworth 2340 P: 02 6765 3199 tamworth@ashdown-ingram.com.au Wagga Wagga Unit 1, 12 Mortimer Place Wagga Wagga 2650 P: 02 6925 5266 waggawagga@ashdown-ingram.com.au Wetherill Park Unit 1, 42 Newton Road Wetherill Park 2164 P: 02 9616 0100 wetherillpark@ashdown-ingram.com.au Wollongong 30B Industrial Road Unanderra 2526 P: 02 4271 2611 wollongong@ashdown-ingram.com.au VICTORIA Bendigo Unit 1, 201 Breen Street Golden Square 3555 P: 03 5443 1900 bendigo@ashdown-ingram.com.au North Geelong 470 Melbourne Road North Geelong 3215 P: 03 5224 2266 geelong@ashdown-ingram.com.au Sandown 13-15 Brough Street Sandown 3171 P: 03 9548 2266 sandown@ashdown-ingram.com.au Sunshine West Unit 6, 42-48 Vella Drive Sunshine 3020 P: 03 9364 7466 sunshinewest@ashdown-ingram.com.au Traralgon 5 Rocla Road Traralgon East 3844 P: 03 5174 9492 traralgon@ashdown-ingram.com.au Tullamarine 9 Tullamarine Park Road Tullamarine 3043 P: 03 8336 6444 tullamarine@ashdown-ingram.com.au NEW ZEALAND Auckland 22 Sylvia Park Road Mt. Wellington 1060 P: +64 9 5730 680 auckland@ashdown-ingram.co.nz Hamilton 126 Ellis Street Frankton 3204 P: +64 7 8471 400 hamilton@ashdown-ingram.co.nz Christchurch 48 Wordsworth Street Sydenham 8023 P: +64 3 3712 770 christchurch@ashdown-ingram.co.nz Copyright 2013 GPC Asia Pacific Pty Ltd. ABN 97 097 993 283 All trademarks, logos and images are the property of GPC Asia Pacific Pty Ltd.