BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY SECTION BRM A BODY REPAIR B C D CONTENTS E FEATURES OF NEW MODEL... 2 BODY EXTERIOR PAINT COLOR... 2 Body Exterior Paint Color...2 PRECAUTION... 3 HANDLING PRECAUTIONS FOR PLASTICS... 3 Precautions For Plastics...3 ON-VEHICLE REPAIR... 7 BODY COMPONENT PARTS... 7 Underbody Component Parts...7 Body Component Parts...9 CORROSION PROTECTION...11 Description...11 Anti-Corrosive Wax...11 Undercoating...12 BODY SEALING...14 Description...14 BODY CONSTRUCTION...17 Body Construction...17 BODY ALIGNMENT...18 Body Center Marks...18 Panel Parts Matching Marks...19 Description...19 Engine Compartment...21 Underbody...23 Passenger Compartment...25 Rear Body...27 Roof...28 PRECAUTIONS IN REPAIRING HIGH STRENGTH STEEL...30 High Strength Steel (HSS)...30...33 Description...33 Hoodledge...38 Front Side Member (Partial Replacement)...39 Front Side Member Assembly...41 Front Pillar...42 Dash Side...45 Center Pillar...46 Front Body Side Outer...49 Rear Body Side Outer...50 Outer Sill Reinforcement...51 Rear Fender...52 Tail Lamp Housing Base...53 Parcel Shelf...55 Rear Wheel Housing...55 Rear Body Side Inner Assembly...56 Rear Floor Rear...57 Rear Panel Assembly...59 Roof...60 Roof Rails, Dual Panel Sunroof...61 Roof Rails, Single Panel Sunroof...61 Roof Side Rail...62 Body Side Inner...63 Rear Center Crossmember...65 Rear Side Member...65 F G H I J BRM L M N O P BRM-1
BODY EXTERIOR PAINT COLOR < FEATURES OF NEW MODEL > FEATURES OF NEW MODEL BODY EXTERIOR PAINT COLOR Body Exterior Paint Color INFOID:0000000004162728 ALKIA1531GB Component Color code NAD RAB W40 KH3 DAD K12 K50 QX3 Description Red Blue Medium Gray M= Metallic, S= Solid, 2S= Solid and Clear, 2P= 2-coat Pearl, 3P= 3-coat pearl, PM=Pearl metallic. Black is solvent based, all others are water based. Black Greyish Green/ Gold Paint type M M M 2S PM M PM 3P Hard clear coat - - - - - 1 Bumper fascia Body color NAD RAB W40 KH3 DAD K12 K50 QX3 2 Front grille Chrome Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P 3 4 5 6 Door outside mirror Door outside handle Center mud guard License lamp finisher Silver Dark Gray White Base Black KH3 KH3 KH3 KH3 KH3 KH3 KH3 KH3 Housing Body color NAD RAB W40 KH3 DAD K12 K50 QX3 Chrome Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Body color NAD RAB W40 KH3 DAD K12 K50 QX3 Chrome Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P BRM-2
< PRECAUTION > HANDLING PRECAUTIONS FOR PLASTICS PRECAUTION HANDLING PRECAUTIONS FOR PLASTICS Precautions For Plastics INFOID:0000000004162729 A B Abbreviation Material name Heat resisting temperature C( F) PE Polyethylene 60(140) Resistance to gasoline and solvents Gasoline and most solvents are harmless if applied for a very short time (wipe up quickly). PVC Poly Vinyl Chloride 80(176) Same as above. EPM/ EPDM TPO/ TPR Ethylene Propylene (Diene) copolymer Thermoplastic Olefine/ Thermoplastic rubber Other cautions Flammable Poison gas is emitted when burned. 80(176) Same as above. Flammable 80(176) Same as above. Flammable PP Polypropylene 90(194) Same as above. Flammable, avoid battery acid. UP Unsaturated Polyester 90(194) Same as above. Flammable PS Polystyrene 80(176) Avoid solvents. Flammable ABS Acrylonitrile Butadiene Styrene 80(176) Avoid gasoline and solvents. PMMA Poly Methyl Methacrylate 85(185) Same as above. EVAC Ethylene Vinyl Acetate 90(194) Same as above. ASA Acrylonitrile Styrene Acrylate 100(222) Same as above. Flammable PPE Poly Phenylene Ether 110(230) Same as above. PC Polycarbonate 120(248) Same as above. PAR Polyarylate 180(356) Same as above. PUR Polyurethane 90(194) Same as above. PPC Polypropylene Composite 115 (239) Same as above Flammable POM Poly Oxymethylene 120(248) Same as above. Avoid battery acid. PBT+ PC Poly Butylene Terephthalate + Polycarbonate 120(248) Same as above. Flammable PA Polyamide (Nylon) 140(284) Same as above. Avoid immersing in water. PBT Poly Butylene Terephthalate 140(284) Same as above. PET Polyester 180(356) Same as above. PEI Polyetherimide 200(392) Same as above. 1. When repairing and painting a portion of the body adjacent to plastic parts, consider their characteristics (influence of heat and solvent) and remove them if necessary or take suitable measures to protect them. 2. Plastic parts should be repaired and painted using methods suiting the materials, characteristics. C D E F G H I J BRM L M N O P BRM-3
< PRECAUTION > LOCATION OF PLASTIC PARTS HANDLING PRECAUTIONS FOR PLASTICS ALKIA1533GB Item Component Abbreviation Material 1. Front combination lamp Lens PC Polycarbonate Housing PP Polypropylene 2. Door mirror Base PA Polyamide (Nylon) Housing ABS Acrylonitrile Butadiene Styrene 3. Front fascia PP Polypropylene BRM-4
< PRECAUTION > HANDLING PRECAUTIONS FOR PLASTICS Item Component Abbreviation Material 4. Mudguard TPO Thermoplastic Olefine 5. Outside door handle 6. Rear combination lamp Grip PC Polycarbonate Escutcheon PA Polyamide (Nylon) Lens PMMA Poly Methyl Methacrylate Housing ABS Acrylonitrile Butadiene Styrene 7. Trunk lid finisher ABS + PC Acrylonitrile Butadiene Styrene + Polycarbonate 8. Rear fascia PP Polypropylene A B C D E F G H I J BRM L ALKIA1534GB Item Component Abbreviation Material 1. Center pillar upper garnish 2. Rear pillar garnish core PP Polypropylene skin PET Polyester core PP Polypropylene skin PET Polyester core PP Polypropylene 3. Rear parcel shelf finisher skin PET Polyester 4. Rear inner kicking plate PP Polypropylene 5. Center console body cup holder storage bin ABS + PC ABS + PC ABS + PC Acrylonitrile Butadiene Styrene + Polycarbonate Acrylonitrile Butadiene Styrene + Polycarbonate Acrylonitrile Butadiene Styrene + Polycarbonate M N O P BRM-5
< PRECAUTION > HANDLING PRECAUTIONS FOR PLASTICS Item Component Abbreviation Material 6. Steering column covers PP Polypropylene 7. Front pillar upper garnish core PP Polypropylene skin PET Polyester 8. Front inner kicking plate PP Polypropylene 9. Center pillar lower garnish PP Polypropylene BRM-6
ON-VEHICLE REPAIR BODY COMPONENT PARTS Underbody Component Parts BODY COMPONENT PARTS INFOID:0000000004162730 A B C D E F G H I J BRM L M N O P AWKIA1342GB BRM-7
BODY COMPONENT PARTS 1. Rear seat lower crossmember 2. Rear floor front 3. Rear floor front extension 4. Rear seat crossmember 5. Front side member rear extension 6. Dash side (RH & LH) (RH & LH) 7. Hoodledge reinforcement (RH & LH) 8. Hoodledge lower assembly (RH & LH) 10. Front side member assembly (RH & LH) 13. Front side member extension (RH & LH) 16. Radiator core side support (RH & LH) 11. Upper radiator core support (RH & LH) 9. Front suspension spring support (RH & LH) 12. Front side member center extension (RH & LH) 14. Front side member (RH & LH) 15. Closing plate assembly (RH & LH) 17. Cowl top center assembly 18. Dash upper 19. Cowl top center 20. Dash lower 21. Front floor center assembly 22. Front floor assembly (RH & LH) 23. Front floor assembly (RH & LH) 24. Front floor (RH & LH) 25. 2nd crossmember assembly (RH & LH) 28. Rear side member assembly (RH & LH) 26. 3rd crossmember assembly (RH & LH) 27 Sill inner assembly (RH &, LH) 29. Rear center crossmember 30. Rear floor rear (RH & LH) 31. Rear floor LH reinforcement 32. Rear floor rear 33. Rear floor RH reinforcement : Both sided anti-corrosive precoated steel portions : High strength steel (HSS) portions : Both sided anti-corrosive steel and HSS portions BRM-8
Body Component Parts BODY COMPONENT PARTS INFOID:0000000004162731 A B C D E F G H I J BRM L M N O AWKIA1343GB P 1. Rear panel assembly 2. Parcel shelf assembly 3. Rear roof rail assembly (single panel sunroof) 4. Roof panel, single panel sunroof 5. Rear roof bow 6. Rear roof rail (dual panel sunroof) 7. Front roof rail dual panel sunroof shown) 8. Body side inner reinforcement (RH & LH)) BRM-9 9. Center pillar inner reinforcement (RH & LH)
BODY COMPONENT PARTS 10. Roof side rail (RH & LH) 11. Center pillar reinforcement (RH & LH) 13. Front pillar lower hinge brace (RH & LH) 14. Front pillar lower reinforcement (RH & LH) 12. Front pillar upper hinge brace (RH & LH) 15. Hood assembly 16. Front body side outer (RH & LH) 17. Outer sill reinforcement (RH & LH) 18. Front fender assembly (RH & LH) 19. front door assembly (RH & LH) 20. Front door outer (RH & LH) 21. Rear door outer (RH & LH) 22. Rear door assembly (RH & LH) 23. Rear body side outer (RH & LH) 24. Tail lamp housing base (RH & LH) 25. Rear body side inner assembly (RH & LH) 28. Rear pillar inner reinforcement (RH & LH) 26. Sill outer reinforcement rear (RH & LH) 27. Rear wheel housing assembly (RH & LH) 29. Rear pillar inner (RH & LH) 30. Rear seatback side support (RH & LH) 31. Parcel shelf side (RH & LH) 32. Rear fender extension (RH & LH) 33. Trunk lid assembly : Both sided anti-corrosive precoated steel portions : High strength steel (HSS) portions : Both sided anti-corrosive steel and HSS portions BRM-10
CORROSION PROTECTION Description CORROSION PROTECTION INFOID:0000000004162732 A To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-corrosive measures. Anti-Corrosive Precoated Steel (Galvannealed Steel) To improve repairability and corrosion resistance, a new type of anticorrosive precoated steel sheet has been adopted replacing conventional zinc-coated steel sheet. Galvannealed steel is electroplated and heated to form Zinc-iron alloy, which provides excellent and long term corrosion resistance with cationic electrodeposition primer. B C D E F SIIA2294E Nissan Genuine Service Parts are fabricated from galvannealed steel. Therefore, it is recommended that GENUINE NISSAN PARTS or equivalent be used for panel replacement to maintain the anti-corrosive performance built into the vehicle at the factory. Phosphate Coating Treatment and Cationic Electrodeposition Primer A phosphate coating treatment and a cationic electrodeposition primer, which provide excellent corrosion protection, are employed on all body components. CAUTION: Confine paint removal during welding operations to an absolute minimum. G H I J BRM Nissan Genuine Service Parts are also treated in the same manner. Therefore, it is recommended that GENU- INE NISSAN PARTS or equivalent be used for panel replacement to maintain anti-corrosive performance built into the vehicle at the factory. Anti-Corrosive Wax PIIA0095E INFOID:0000000004162733 To improve corrosion resistance, anti-corrosive wax is applied inside the body sill and inside other closed sections. Accordingly, when replacing these parts, be sure to apply anti-corrosive wax to the appropriate areas of L M N O P BRM-11
CORROSION PROTECTION the new parts. Select an excellent anti-corrosive wax which will penetrate after application and has a long shelf life. AWKIA1344GB Undercoating INFOID:0000000004162734 The underside of the floor and wheelhouse are undercoated to prevent rust, vibration, noise and stone chipping. Therefore, when such a panel is replaced or repaired, apply undercoating to that part. Use an undercoating which is rust preventive, soundproof, vibration-proof, shock-resistant, adhesive, and durable. Precautions in Undercoating 1. Do not apply undercoating to any place unless specified (such as the areas above the muffler and three way catalyst which are subjected to heat). 2. Do not undercoat the exhaust pipe or other parts which become hot. 3. Do not undercoat rotating parts. 4. Apply bitumen wax after applying undercoating. BRM-12
CORROSION PROTECTION 5. After putting seal on the vehicle, put undercoating on it. A B C D E F G AWKIA1345GB H I J BRM L M N O P BRM-13
BODY SEALING Description BODY SEALING INFOID:0000000004162736 The following figure shows the areas which are sealed at the factory. Sealant which has been applied to these areas should be smooth and free from cuts or gaps. Care should be taken not to apply an excess amount of sealant and not to allow other unaffected parts to come into contact with the sealant. AWKIA1346GB BRM-14
BODY SEALING A B C D E F G H I J BRM L M N O AWKIA1347GB P BRM-15
BODY SEALING AWKIA1348GB BRM-16
BODY CONSTRUCTION Body Construction BODY CONSTRUCTION INFOID:0000000004162737 A B C D E F G H I J BRM L M N O P AWKIA1349GB BRM-17
BODY ALIGNMENT Body Center Marks BODY ALIGNMENT INFOID:0000000004162738 A mark has been placed on each part of the body to indicate the vehicle center. When repairing parts damaged by an accident which might affect the vehicle frame (members, pillars, etc.), more accurate and effective repair will be possible by using these marks together with body alignment specifications. AWKIA1350GB BRM-18
Panel Parts Matching Marks BODY ALIGNMENT INFOID:0000000004162739 A mark has been placed on each body panel to indicate the parts matching positions. When repairing parts damaged by an accident which might affect the vehicle structure (members, pillars, etc.), more accurate and effective repair will be possible by using these marks together with body alignment specifications. A B C D E F G H I J BRM L M Description AWKIA1351GB INFOID:0000000004162740 N All dimensions indicated in the figures are actual. When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself to make sure there is no free play. When a measuring tape is used, check to be sure there is no elongation, twisting or bending. Measurements should be taken at the center of the mounting holes. An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side is symmetrically the same value. The coordinates of the measurement points are the distances measured from the standard line of X, Y and Z. O P BRM-19
BODY ALIGNMENT PIIA0104E BRM-20
Engine Compartment Measurement BODY ALIGNMENT INFOID:0000000004162741 A B C D E F G H I J BRM L M N O P AWKIA1352GB BRM-21
Measurement Points BODY ALIGNMENT AWKIA1353GB BRM-22
Underbody Measurement BODY ALIGNMENT INFOID:0000000004162742 A B C D E F G H I J BRM L M N O P AWKIA1354GB BRM-23
Measurement Points BODY ALIGNMENT AWKIA1355GB BRM-24
Passenger Compartment Measurement BODY ALIGNMENT INFOID:0000000004162743 A B C D E F G H I J BRM L M N O P AWKIA1356GB BRM-25
Measurement Points BODY ALIGNMENT AWKIA1357GB BRM-26
Rear Body Measurements BODY ALIGNMENT INFOID:0000000004162744 A B C D E F G H I J BRM L M N O P AWKIA1358GB BRM-27
Roof BODY ALIGNMENT INFOID:0000000004209505 MEASUREMENTS (DUAL PANEL SUNROOF) AWKIA1359GB BRM-28
BODY ALIGNMENT < ON-VEHICLE REPAIR > MEASUREMENT POINTS (DUAL PANEL SUNROOF) A B C D E F G H I J BRM L M N O AWKIA1360GB P BRM-29
PRECAUTIONS IN REPAIRING HIGH STRENGTH STEEL < ON-VEHICLE REPAIR > PRECAUTIONS IN REPAIRING HIGH STRENGTH STEEL High Strength Steel (HSS) INFOID:0000000004291546 High strength steel is used for body panels in order to reduce vehicle weight. Accordingly, precautions in repairing automotive bodies made of high strength steel are described below: Tensile strength 370-590 MPa 780-1350 MPa Major applicable parts Lower front and rear hoodledge Upper hoodledge Side dash Roof bow No. 2 and No.4 3rd crossmember (Front floor component part) Inner sill Rear side member assembly Rear seat crossmember Center rear crossmember assembly Inner side roof rail Inner center pillar Inner center front bumper reinforcement Front bumper stay Rear side bumper bracket Other reinforcements Front side member assembly Front side member closing plate assembly Front side member extension Front side member center extension Outer roof rail reinforcement (Side body assembly component part) 2nd crossmember (Front floor component part) Read the following precautions when repairing HSS: 1. Additional points to consider The repair of reinforcements (such as side members) by heating is not recommended since it may weaken the component. When heating is unavoidable, do not heat HSS parts above 550 C (1,022 F). Verify heating temperature with a thermometer. (Crayon-type and other similar type thermometer are appropriate.) PIIA0115E When straightening body panels, use caution in pulling any HSS panel. Because HSS is very strong, pulling may cause deformation in adjacent portions of the body. In this case, increase the number of measuring points, and carefully pull the HSS panel. PIIA0116E BRM-30
PRECAUTIONS IN REPAIRING HIGH STRENGTH STEEL When cutting HSS panels, avoid gas (torch) cutting if possible. Instead, use a saw to avoid weakening surrounding areas due to heat. If gas (torch) cutting is unavoidable, allow a minimum margin of 50 mm (1.97 in). A B C When welding HSS panels, use spot welding whenever possible in order to minimize weakening surrounding areas due to heat. If spot welding is impossible, use MIG. welding. Do not use gas (torch) for welding because it is inferior in welding strength. PIIA0117E D E F G JSKIA0082GB The spot weld on HSS panels is harder than that of an ordinary steel panel. Therefore, when cutting spot welds on a HSS panel, use a low speed high torque drill (1,000 to 1,200 rpm) to increase drill bit durability and facilitate the operation. H I J 2. Precautions in spot welding HSS This work should be performed under standard working conditions. Always note the following when spot welding HSS: The electrode tip diameter must be sized properly according to the metal thickness. PIIA0145E BRM L M N PIIA0146E O P BRM-31
PRECAUTIONS IN REPAIRING HIGH STRENGTH STEEL < ON-VEHICLE REPAIR > The panel surfaces must fit flush to each other, leaving no gaps. PIIA0147E Follow the specifications for the proper welding pitch. Unit: mm (in) Thickness (t) 0.6 (0.024) 0.8 (0.031) 1.0 (0.039) 1.2 (0.047) 1.6 (0.063) 1.8 (0.071) Minimum pitch (l) 10 (0.39) or over 12 (0.47) or over 18 (0.71) or over 20 (0.79) or over 27 (1.06) or over 31 (1.22) or over PIIA0148E BRM-32
Description INFOID:0000000004162746 A This section is prepared for technicians who have attained a high level of skill and experience in repairing collision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body repair techniques should not attempt to repair collision-damaged vehicles by using this section. Technicians are also encouraged to read Body Repair Manual (Fundamentals) in order to ensure that the original functions and quality of the vehicle can be maintained. The Body Repair Manual (Fundamentals) contains additional information, including cautions and warnings, that are not including in this manual. Technicians should refer to both manuals to ensure proper repairs. Please note that this information is prepared for worldwide usage, and as such, certain procedures might not apply in some regions or countries. B C D E F G H I J BRM L M N O P BRM-33
The symbols used in this section for cutting and welding / brazing operations are shown below. PIIA0149E BRM-34
Front pillar butt joint can be determined anywhere within shaded area as shown in the figure. The best location for the butt joint is at position A due to the construction of the vehicle. Refer to the front pillar section. A B C Determine cutting position and record distance from the locating indent. Use this distance when cutting the service part. Cut outer front pillar over 60 mm above inner front pillar cut position. PIIA0150E D E F G PIIA0151E Prepare a cutting jig to make outer pillar easier to cut. Also, this will permit service part to be accurately cut at joint position. H I J PIIA0152E BRM An example of cutting operation using a cutting jig is as follows. 1. Mark cutting lines. A: Cut position of outer pillar B: Cut position of inner pillar 2. Align cutting line with notch on jig. Clamp jig to pillar. 3. Cut outer pillar along groove of jig. (At position A) 4. Remove jig and cut remaining portions. 5. Cut inner pillar at position B in same manner. L M N PIIA0153E FOAM REPAIR During factory assembly, foam insulators are installed in certain body panels and locations around the vehicle. Use the following procedure(s) to replace any factory-installed foam insulators. Urethane Foam Applications Use commercially available spray for sealant (foam material) repair of material used on vehicle. Read instructions on product for fill procedures. O P Fill Procedures 1. Fill procedures after installation service part. Remove foam material remaining on vehicle side. BRM-35
Clean area in which foam was removed. Install service part. Insert nozzle into hole near fill area and fill foam material or fill in enough to close gap with service part. 2. Fill procedures before installation service part Remove foam material remaining on vehicle side. Clean area in which foam material on wheelhouse outer side was removed. NOTE: Fill in enough to close gap with service part while avoiding flange area. Install service part. NOTE: Refer to label for information on working times. LIIA1081E LIIA1082E BRM-36
A B C D E F G H I J BRM L M N AWKIA1361GB 1. Body side outer 2. Body side insulation (foam) upper front pillar 4. Roof panel assembly 5. Roof panel insulation (foam) front roof rail (standard roof) 7. Body side insulation (foam) lower rear pillar Note: Views F & G are shown with the body side outer removed. 8. Body side insulation strip front pillar lower reinforcement 3. Body side insulation (foam) front pillar 6. Body side insulation (foam) rear pillar 9. Body side insulation strip, center pillar reinforcement O P BRM-37
Hoodledge INFOID:0000000004162747 AWKIA1363GB Replacement parts Front suspension spring support Hoodledge reinforcement Hoodledge lower assembly Upper radiator core support BRM-38
Front Side Member (Partial Replacement) Work after the hoodledge has been removed. INFOID:0000000004162748 A B C D E F G H I J BRM L M N O P AWKIA1364GB Replacement parts Front side member Closing plate assembly Radiator core side support Front suspension member weld nut plate Work after front side member and closing plate assembly have been removed. BRM-39
AWKIA1365GB Replacement parts Front side member extension Shown with front side member extension removed. BRM-40
A B C D E F G H I J BRM L M N O Replacement parts Front side member center extension Front Side Member Assembly Work after hoodledge has been removed. AWKIA1366GB INFOID:0000000004162749 P BRM-41
AWKIA1367GB Replacement parts Front side member assembly Front Pillar INFOID:0000000004162750 OUTER Work after the upper hoodledge has been removed. BRM-42
A B C D E F G H I J BRM L M N O AWKIA1368GB Replacement parts Front pillar section of front body side outer P REINFORCEMENT Work after front pillar section of the front body side outer has been removed. BRM-43
AWKIA1369GB Replacement parts Front pillar upper hinge brace Front pillar lower hinge brace INNER Work after front pillar upper hinge brace has been removed. BRM-44
A B C D E F G H I J BRM L M N O Replacement parts Front pillar inner reinforcement (partial) Dash Side AWKIA1370GB INFOID:0000000004162751 P Work after the front pillar portion of body side inner reinforcement and the front pillar lower hinge brace have been removed. BRM-45
AWKIA1371GB Replacement parts Dash side Center Pillar INFOID:0000000004162752 OUTER BRM-46
A B C D E F G H I J BRM L M N O AWKIA1372GB Replacement parts Center pillar portion of front body side outer P REINFORCEMENT Work after center pillar portion of front body side outer has been removed. BRM-47
AWKIA1373GB Replacement parts Center pillar reinforcement INNER Work after center pillar reinforcement has been removed. BRM-48
A B C D E F G H I J BRM L M N O Replacement parts Center pillar inner reinforcement Front Body Side Outer Work after hoodledge reinforcement and front roof rail have been removed. AWKIA1374GB INFOID:0000000004209118 P BRM-49
AWKIA1375GB Replacement parts Front body side outer Rear Body Side Outer INFOID:0000000004209200 Work after the tail lamp housing base and rear roof rail have been removed. BRM-50
A B C D E F G H I J BRM L M N O Replacement parts Rear body side outer Outer Sill Reinforcement AWKIA1376GB INFOID:0000000004162753 P Work after the front pillar lower hinge brace and the center pillar reinforcement have been removed. BRM-51
AWKIA1377GB Replacement parts Outer sill reinforcement Rear Fender INFOID:0000000004162755 Work with tail lamp housing base removed. BRM-52
A B C D E F G H I J BRM L M N O Replacement parts Rear fender Tail Lamp Housing Base Work after rear panel assembly has been removed. AWKIA1378GB INFOID:0000000004162758 P BRM-53
AWKIA1379GB Replacement parts Tail lamp housing base BRM-54
Parcel Shelf INFOID:0000000004209312 A B C D E F G H I J BRM L M N O AWKIA1380GB P Replacement part Parcel shelf assembly Rear Wheel Housing INFOID:0000000004209385 Work after the rear body side outer and the parcel shelf have been removed. BRM-55
AWKIA1381GB Replacement parts Rear wheel housing assembly Rear pillar inner reinforcement Parcel shelf side Rear seatback side support Sill outer reinforcement rear Rear pillar inner Rear Body Side Inner Assembly INFOID:0000000004162757 Work after rear body side outer and parcel shelf have been removed. BRM-56
A B C D E F G H I J BRM L M N O Replacement parts Rear body side inner assembly Rear Floor Rear Work after rear panel assembly has been removed. AWKIA1382GB INFOID:0000000004162759 P BRM-57
AWKIA1383GB Replacement parts Rear floor rear Rear floor rear (RH) Rear floor rear (LH) BRM-58
Rear Panel Assembly INFOID:0000000004162756 A B C D E F G H I J BRM L M N O AWKIA1384GB P Replacement parts Rear panel assembly BRM-59
Roof INFOID:0000000004209313 AWKIA1385GB Replacement parts Roof panel, single panel sunroof BRM-60
Roof Rails, Dual Panel Sunroof INFOID:0000000004209314 A B C D E F G H I J BRM L M N O Replacement parts Front roof rail Rear roof rail Roof Rails, Single Panel Sunroof AWKIA1386GB INFOID:0000000004209315 P Work after the roof has been removed. BRM-61
AWKIA1387GB Replacement parts Front roof rail (sunroof) Rear roof rail (sunroof) Roof Side Rail INFOID:0000000004209316 Work after the front and rear body side outer have been removed. BRM-62
A B C D E F G H I J BRM L M N O Replacement parts Roof side rail Body Side Inner Work after the roof side rail and the center pillar reinforcement have been removed. AWKIA1388GB INFOID:0000000004209347 P BRM-63
AWKIA1389GB Replacement parts Body side inner BRM-64
Rear Center Crossmember INFOID:0000000004209348 A B C D E F G H I J BRM L M N O Replacement parts Rear center crossmember Rear Side Member Work after rear panel assembly and rear center crossmember have been removed. BRM-65 AWKIA1390GB INFOID:0000000004162760 P
AWKIA1391GB Replacement parts Rear side member assembly BRM-66