INSTALLATION INSTRUCTIONS Accessory Application Publications No. THIRD-ROW P/N 08R12-SHJ-100 2008 ODYSSEY AII 38141 Issue Date OCT 2007 PARTS LIST Left rear sunshade Driver s Side 1. Remove the spare tire cover from the left rear side liner (11 tabs). SIDE LINER 11 Right rear sunshade 4 Brackets 4 Rivets SPARE TIRE 4122010Y 2. If equipped, remove the anchor bolt and the anchor bolt cover and take out the spare tire. SPARE TIRE TOOLS AND SUPPLIES REQUIRED Felt-tip pen Center punch Drill 7 mm Drill bit Isopropyl alcohol 6-inch scale Hammer Tape BOLT INSTALLATION NOTE: This sunshade should be installed only if the ambient air temperature is 60 F (15 C) or above. BOLT 4122020Y Allow the adhesive to cure for 24 hours before attaching the sunshade to the bracket. 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 38141 (0710) 08R12-SHJ-1003-91 1 of 6
3. Pull away the weatherstrip from the left rear side trim panel. Remove the anchor bolt, disengage the three clips and the four retaining tabs, and pull out the rear portion of the left rear side trim panel. 5. While gently pulling on the side trim panel, fit the two brackets from the left rear sunshade over the edge of the left rear side trim panel. Align the rear edge of the sunshade with the rear edge of the seat belt cover. 4 RETAINING 3 CLIPS 2 S BOLT FRONT WEATHERSTRIP SIDE TRIM 4326050Y 4. Remove the left speaker cover (two clips and three retaining tabs). SIDE TRIM 2 CLIPS 5 mm SEAT BELT 7611010X 6. Using a felt-tip pen, mark the left rear side trim through the center of each bracket hole. Remove the rear sunshade. FELT-TIP PEN 3 RETAINING LEFT SPEAKER 4326060Y 2 S 4326080Y 2 of 6 AII 38141 (0710) 2007 American Honda Motor Co., Inc. - All Rights Reserved.
7. Center-punch the marks you made in the left rear side trim panel and drill each mark with a 7 mm drill bit: Using adhesive tape, wrap the end of the drill bit 5 mm from the tip. While wearing eye protection, drill a 7 mm hole through each center-punched mark. Remove any burrs from the drilled holes. 10. Insert a 6-inch scale against the top of the rear window between the glass and the headliner until the scale contacts the top of the glass. Measure 25 mm down from the top of the glass, and attach strips of masking tape to the window in the areas shown. 7 mm DRILL BIT 5 mm CENTER PUNCH 7 mm DRILL BIT STOP AT TOP OF SIDE TRIM 25 mm LEFT REAR 6-INCH SCALE 4427040Y 8. Reinstall the left rear sunshade on the left rear side trim panel, and align the brackets from the left rear sunshade with the holes you drilled. RIVET 2 S 4326091Y 11. Pull up the left rear sunshade. Align the two cutouts in the left rear sunshade with the two strips of masking tape attached to the rear window. Using a felt-tip pen, mark the top of the masking tape at each side of cutout in the rear sunshade. Roll down the left rear sunshade. SIDE TRIM CUTOUT IN FELT-TIP PEN Holes drilled in step 7. 4326100Y 9. Secure the two brackets from the left rear sunshade to the left rear side trim panel with the two rivets. Reinstall the left rear side trim panel. SIDE TRIM 4427050Y 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 38141 (0710) 3 of 6
12. Using isopropyl alcohol on a shop towel, clean the left rear window above the marks you made on the masking tape. ROOF LINING STOP AT TOP OF BACKING Align with the bracket. Passenger s Side 15. Pull away the weatherstrip from the right rear side trim panel. Remove the anchor bolt. Disengage the two clips and the four retaining tabs, and pull up on the right rear side trim panel. Apply finger pressure to the entire surface of the bracket for 15 seconds at several places. ATTACHMENT POSITION 2 CLIPS 4 RETAINING BOLT WEATHERSTRIP SIDE TRIM 4329070Y LEFT REAR 16. Remove the right rear speaker cover (two clips and three retaining tabs). 6718040B 13. Remove the adhesive backing from one of the brackets, and attach the bracket to the top of the right rear window between the marks on the masking tape. Slightly turn up the roof lining. Place the tape surface on the upper side of the bracket against the glass surface. Apply force to the bracket so that it becomes curved, and gradually push downward to attach it. Remove the masking tape from the window. Apply finger pressure to the bracket for 15 seconds to allow the tape to adhere to the glass. Install the other bracket the same way. NOTE: Be careful, as wrinkles will form when the roof lining is turned up. 14. If equipped, reinstall the spare tire and the spare tire cover. 2 CLIPS RIGHT SPEAKER 3 RETAINING SIDE TRIM 4329080Y 4 of 6 AII 38141 (0710) 2007 American Honda Motor Co., Inc. - All Rights Reserved.
17. While gently pulling on the side trim panel, fit the two brackets from the right rear sunshade over the edge of the rear side trim panel. Align the rear edge of the sunshade 20 mm from the rear edge of the seat belt cover. FRONT 19. Center-punch the marks you made in the right rear side trim panel and drill each mark with a 7 mm drill bit: Using adhesive tape, wrap the end of the drill bit 5 mm from the tip. While wearing eye protection, drill a 7 mm hole through each center-punched mark. Remove any burrs from the drilled holes. 7 mm DRILL BIT SEAT BELT 20 mm 5 mm CENTER PUNCH 7 mm DRILL BIT 4329091Y 2 S SIDE TRIM 2 S 4329101Y 18. Using a felt-tip pen, mark the right rear side trim through the center of each bracket hole. Remove the rear sunshade. 20. Reattach the rear sunshade on the side trim panel, and align the brackets over the drilled holes in the trim panel. FELT-TIP PEN 2 RIVETS 2 S 4329110Y Holes drilled in step 19. 4329120Y 21. Secure the rear sunshade to the rear trim panel using two rivets from the kit, then reinstall the rear trim panel. 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 38141 (0710) 5 of 6
22. Insert a 6-inch scale against the top of the rear window between the glass and the headliner until the scale contacts the top of the glass. Measure 25 mm down from the top of the glass, and attach strips of masking tape to the window in the areas shown. 24. Using isopropyl alcohol on a shop towel, clean the right rear window above the marks you made on the masking tape. Align with the bracket. STOP AT TOP OF ATTACHMENT POSITION ROOF LINING S 6 INCH SCALE STOP AT TOP OF 25 mm BACKING Apply finger pressure to the entire surface of the bracket for 15 seconds at several places. 4428010Y 23. Pull up the rear sunshade until the cutouts in the sunshade reach the masking tape. Using a felt-tip pen, mark the top of the masking tape at each side of each cutout. Roll down the rear sunshade. RIGHT REAR 6718050B CUTOUT IN FELT-TIP PEN 25. Remove the adhesive backing from one of the brackets and attach the bracket to the top of the right rear window between the marks on the masking tape. Slightly turn up the roof lining. Place the tape surface on the upper side of the bracket against the glass surface. Apply force to the bracket so that it becomes curved, and gradually push it downward to attach it). Remove the masking tape from the window. Apply finger pressure to the bracket for 15 seconds to allow the tape to adhere to the glass. Install the other bracket the same way. NOTE: Be careful, as wrinkles will form when the roof lining is turned up. 4428020Y 6 of 6 AII 38141 (0710) 2007 American Honda Motor Co., Inc. - All Rights Reserved.