TRUCK ACCESSORIES PAGE Service Bodies 2 Service Body Options 5 Special Bodies (Compact & Full Size Trucks) 7 Tonneau Cover 9 Toppers 9 Ladder Racks 12 Lights 13 Van Accessories 15 Trailer Towing Packages 17 Hyrail 19 Electric Winch 22 Tool Chests 22 Pull Out Tool Drawers 23 Cranes 25 Crane Accessories 33 Hydraulic Tool Circuit 34 Bed Mat 35 Air Compressor 35 Platform Bodies 36 Dump Bodies 36 Dump Body Accessories 37 Platform Body Accessories 37 Welding Machines 39 Work Platform 43 Electrical Power 43 Rail Lubricators 44 Police Equipment 46 Company Radios 46 Revised May, 2014 1
Decals 48 Miscellaneous Equipment 48 SERVICE BODIES All service bodies to incorporate a service body cab guard of 2 square tubing with screened window. Guard is to be mounted to the front of the body and reinforced to the bulkhead. All doors to have removable stainless steel hinges and to be sealed with automotive type snap on weather-stripping. All doors to have locking T-handle latches and to be keyed alike, vertical doors to have spring-loaded stops, all doors to have a 3-point latching system, Cargo floor is to be of 1/8 steel treadplate formed to interlock with side compartments with 2 recessed tie down rings located 6 from sides and 18 from tailgate. A locking bed mounted spare tire carrier is to be provided. A heavy duty step type bumper with provisions for the attached of two safety tow chains will be reinforced to the frame of the chassis. Wiring to be sealed style, Lights to be recessed and to comply with all federal and state laws. Bodies to be mounted on steel risers with grade 8 or equivalent fasteners in accordance with body manufacturer s recommendations, Bodies to be painted in acrylic enamel to match the cab. Non-skid paint to be used on all walking surfaces including the tops of side compartments, Cab guard to be painted black, The bottom of all compartments will include a water drain hole plus underbody v-wedge and Dri-Deck (or equal) liner on the floor of the compartment. Provide underbody fuel line guards to protect lines from flat tires. LED stop, tail, & turn signal lights. All service body compartments, underbody boxes, and any other body compartments with locks to have locks keyed to match the ignition key. Supply four (4) keys per truck. UP 1A Low profile service body, 8 L Reading LP98BA or equivalent 76 ½ W x 96 L 48 ½ W cargo area 14 side compartment depth Minimum of 20 floor to top of body height 3 compartments each side First compartment (streetside and curbside) 28 W x 35 ¾ H x 14 D Vertical hinged door Two adjustable shelves and removable dividers Second compartment (streetside) 68 W x 14 ¼ H x 14 D Horizontally opening door Adjustable shelf and removable dividers Second compartment (curbside) 48 W x 14 ½ H X 14 D Horizontally opening door Adjustable shelf and removable dividers Third compartment (streetside) 20 W x 17 ½ H x 14 D Vertically hinged door Third compartment (curbside) 20 W x 31 ¾ H x 14 D Vertically hinged door 2 adjustable shelves and removable dividers Wt. 1,035 lbs. Revised May, 2014 2
UP 1AD Low profile service body, 8 L. Reading LP98BADW or equivalent (for dual rear wheel chassis with 56 CA) 90 W x 96 L 50 W cargo area 20 side compartment depth Minimum of 20 floor to top of body height 3 compartments for each side: First compartment (streetside and curbside) 28 W x 35 ¾ H x 20 D Vertically hinged door Two adjustable shelves and removable dividers Second compartment (streetside) 68 W x 14 ¼ H x 20 D Horizontally opening door Adjustable shelf and removable dividers Second compartment (curbside) 48 W x 14 ¼ H x 20 D Horizontally opening door Adjustable shelf and removable dividers Third compartment (streetside) 20 W x 17 ½ H x 20 D Vertically hinged door Third compartment (curbside) 20 W x 31 ¾ H x 20 D Vertically hinged door 2 adjustable shelves and removable dividers Wt. 1,298 lbs. UP 1B Spacemaker low profile service body, 8 L (top opening compartments), Reading SLP98BA or equivalent. 76 ½ W x 96 L Revised May, 2014 3
48 ½ W cargo area 14 side compartment depth Minimum of 20 floor to top of body height 4 compartments each side: First compartment (streetside and curbside) 28 W x 35 ¾ H x 14 D Vertically hinged door Two adjustable shelves and removable dividers Second compartment (streetside) 68 W x 14 ¼ H x 14 D Horizontally opening door Adjustable shelf and removable dividers Second compartment (curbside) 48 W x 14 ¼ H x 14 D Horizontally opening door Adjustable shelf and removable dividers Third compartment (streetside) 20 W x 17 ½ H x 14 D Vertically hinged door Third compartment (curbside) 20 W x 31 ¾ H x 14 D Vertically hinged door 2 adjustable shelves and removable dividers Top compartments (streetside and curbside) Top opening tray 96 L x 14 W x 4 D Wt.1,160 lbs UP 1C Low profile service body, 9 L Reading LP108BADW or equivalent (for dual rear wheel chassis with 60 CA) 90 W x 108 L 50 W cargo area 20 side compartment depth Minimum of 20 floor to top of body height 3 compartments each side: First compartment (streetside and curbside) 34 ¾ W x 35 ¾ H x 20 D Vertically hinged door Two adjustable shelves and removable dividers Second compartment (streetside) 73 ¼ W x 14 ¼ H x 20 D Horizontally opening door Adjustable shelf and removable dividers Third compartment (streetside) 26 ¼ W x 17 ½ H x 20 D Revised May, 2014 4
Vertically hinged door Third compartment (curbside) 26 ¼ W x 31 ¾ H x 20 D Vertically hinged door Two adjustable shelved and removable dividers Wt. 1,238 lbs. UP 1D Low profile aluminum service body, 8 L Reading Aluminum ULP98-SW BA or equivalent 76 ½ W x 98 L 48 ½ W cargo area 14 side compartment depth Minimum of 20 floor to top of body height 3 compartments each side First compartment (streetside and curbside) 28 W x 35 ¾ H x 14 D Vertical hinged door Two adjustable shelves and removable dividers Second compartment (streetside) 68 W x 14 ¼ H x 14 D Horizontally opening door Adjustable shelf and removable dividers Second compartment (curbside) 48 W x 14 ½ H X 14 D Horizontally opening door Adjustable shelf and removable dividers Third compartment (streetside) 20 W x 17 ½ H x 14 D Vertically hinged door Third compartment (curbside) 20 W x 31 ¾ H x 14 D Vertically hinged door 2 adjustable shelves and removable dividers Wt. 596 lbs. SERVICE BODY OPTIONS UP ST Sliding telescopic steel top with locking T handle latch, keyed to match other doors on Revised May, 2014 5
body. Requires top mounted spare tire carrier. Wt. 152 lbs. UP CR Crane reinforcement for curbside rear compartment of low profile service body. Includes remote control pendant hanger bracket. Required with any crane. (Not available on UP 1B, Spacemaker body) Wt. 100 lbs. UP GB 60 Gas bottle compartment to replace the front streetside compartment. (Available with UP 1A, UP 1 AD and UP 1C bodies only) GB configuration must fit in Ship Thru. Wt. 50 lbs UP ML Master locking system: A rod type system that locks all doors on each side of the body simultaneously; the rod can be secured with a padlock. Wt. 20 lbs. Revised May, 2014 6
UP FUEL Light Duty Fuel Truck 110 gallon one product fuel tank mounted in front of bed at bulkhead. 12 volt DC battery powered fuel pump with 13 GPM capacity. Equipped with safety switch, Spring loaded hose reel with 12 of 5/8 diameter hose, mounted on top of curbside first compartment. Ground wire with reel Wt. 244 lbs SPECIAL BODIES (Compact and Full Size Trucks) UP YARD Car maintenance truck (compact) Yard body - Aluminum 72" long Gas bottle rack both sides Revised May, 2014 7
Rubber pads in bottom of bottle racks Aluminum sides and dividers Bulkhead w/window Buyers tool box street side Tool holder Long bar holder Torch holder with rubber pad Knuckle holder Knuckle pin holder 6" composite side boards CHSML light, backup lights, and backup alarm mounted on cab guard. Single step rear bumper Mount spare tire under bed at rear Helper springs Torch reel w/50' of 3/8" twin hose (6) LED work lights - 3 on driver s side and 3 on passenger s side LED stop, tail, & turn signal lights UP PLATFORM Car maintenance truck (compact) Platform body - Steel 72" long Revised May, 2014 8
TONNEAU COVER (for Full Size Pickup with Short or Long Bed) UP TON-1 A.R.E. Fiberglass Tonneau Cover (alligator style) with bed slide, Bed Side to have three locking positions, sealed rollers with aluminum side rails and 7 ply marine decking with 1/4" rubber mat. 1200 lb capacity Wt. 340 lbs UP TON-2 Diamondback powder coat metal bed cover with Rhino Liner coating Wt. 70 lbs UP TON-3 A.R.E. Fiberglass Tonneau cover (alligator style) Wt. 65 lbs TOPPERS (for Full Size Pickup with Short or Long Bed) UP TOP-1 (Standard topper for Engineering Department) Reading Ready Cap or equivalent (cab high 23 ) White painted galvanneal steel heavy duty Full length side doors with 12 x 59 radius window both sides Half rear door with clear mitered window and lock. Front clear 12 x 36 window with security screen. Third brake light Two (2) interior lights located over rear door and center with pin switches at all three doors. Foam roof liner. Includes bed mounted access steps on driver & passenger side Wt. 225 lbs Revised May, 2014 9
UP TOP-2 (Standard topper for Information Technology Department) Reading Ready Cap or equivalent Cab high plus 4 (27 OAH) Exterior skin: white painted galvaneeled steel heavy duty Dome lights: two, centered on ceiling with rear door and curb side door switches. Goalpost style cargo/ladder rack with center support, Single ear on curb side to keep ladder from sliding Foam roof liner (reduces moisture inside topper). Side doors: one full length door on each side with strut assists and lock Double side opening rear doors Windows: clear front 12 x 36 window with security screen Dark tint 8 x 30 radius rear door windows Dark tint 8.5 x 59 window in curbside door. No window in streetside door. Door latches: T-handle latches with 3-point locking mechanisms. Tool box: fills side door opening on driver s side. Includes four vertical dividers, evenly spaced. Includes bed mounted access steps on driver & passenger side Upfitter to dispose of tailgate with credit applied towards installation of the topper. Wt. 528 lbs UP TOP-3 (Topper for Information Technology Department) ARE DCU aluminum topper with streetside opening door with an enclosed shelf Swing open double rear doors with privacy glass Glass in the front with a screen, privacy glass on curbside No insulation, goal post ladder rack. Includes bed mounted access steps on driver & passenger side Upfitter to dispose of tailgate with credit applied towards installation of the topper. Revised May, 2014 10
UP TOP-3B Bed slide in combination with UP TOP-3 ARE DCU aluminum topper. UP TOP-4 ARE CX Series Fiberglass Cab High Topper Side opening doors with shelves both sides Swing up rear door no window Includes bed mounted access steps on driver & passenger side LED light switch at rear Wt. 195 lbs UP EB6 Extendo Bed: EB-1270-70 steel frame assembly with a full extension lock 48 x 70 /68-3/4 plywood platform with short metal side rails. Platform 4-1/2 x 6 - UPF-4868-3/4 12 with a cutaway with safety screen, center partition, & containment caging. Drawer - Two aluminum drawers with dividers including screening and rubber mat on floor. Mounting Wall (Slide out) - Fold down work table and slide-out mounting wall with aluminum diamond plate on outside and Poly on inside and mounting side of slider wall. Wt. 800 lbs UP JB6 Bedslide Roll-Out Load Floor for short bed pickups Wt. 188 lbs UP JB8 Bedslide Roll-Out Load Floor for long bed pickups Wt. 216 lbs Revised May, 2014 11
LADDER RACKS UP 3 Bow type ladder rack for overhead storage of ladders, 200 lb. capacity. Wt. 40 lbs UP 3A Side mount ladder rack, mounted streetside incorporating a rack for carrying crossing arm gates and a tie down device for the ladder and the crossing arms. Ladder rests to be horizontal plus roller for rear rest. Includes rack strap.. 300 lb. capacity. Wt. 30 lbs UP 3B Heavy duty pipe rack, equipped with roller or rear rack, 1,000 lb. capacity. Wt. 150 lbs Revised May, 2014 12
LIGHTS UP 4 LED Post mounted spotlight. Wt. 7 lbs UP 4A Magnetic mount spot/flood light, single halogen light with 100,000 candle power flood, 200,000 candle power spot. Includes a 20 foot cord, plugs into receptacle in cab or receptacle at rear of truck Wt. 5 lbs UP 4B Handheld spotlight, 200,000 candle power halogen light. Wt. 5 lbs Revised May, 2014 13
UP 4D (2) LED work lights, mounted on bulkhead. 10-30V DC; Flood pattern, Includes dash mounted lighted control switch. Wt. 16 lbs UP 4E Driving lights, dual with lighted switch in cab. Please specify driving or fog lights. Wt. 5 lbs Revised May, 2014 14
UP 4F Golight (equal) remote controlled 100,000 CP halogen spotlight. Rotates 370 degrees plus 70 degree vertical sweep, Cigar plug connector with 10 cord. Magnetic mount. Golight model 7900 or equal Wt. 2 lbs UP 4G Directional light bar. Includes control box mounted in cab. Whelen Model TA837A or equal. Wt. 20 lbs UP 4H Directional light bar, LED viper lights, amber on driver side, amber for all others, mounted at rear on cab guard. Amber LED impaxx mounted rear low and to the outside with guard. Side LED amber impaxx on both sides, end of light bar with rail gear only. Front LED amber impaxx in grill driver side, front amber LED impaxx in grill on passenger side. Visor LED impaxx amber on driver side, visor LED amber on passenger side. Switch 3 position rocker for directional bar, up for right traffic, down for right traffic Switch 3 position rocker, up for rail (no visors lights), down for highway, it will power all the warning lights and the directional light bar will be center out. Diagonal red reflective 3M stripping on rear total of 6 strips UP 4X Additional 4-prong receptacle for UP 4A light specify location. Wt. 1 lb UP 4Y Strobe Light Revised May, 2014 15
UP 4Z LED Strobe Light Except as noted, all lights are available on any truck, van or utility vehicle VAN ACCESSORIES UP 5 3 piece partition with return panel Included with all van packages Wt. 65 lbs UP 5A Nevlen MV100 Package 3 piece partition with center door and return panel Curbside: E77M Rack Streetside: 504 4 drawer cabinet E70M Rack Roof vent & pilot switch Heavy duty cargo floor mat UP 5B Nevlen MV110 Package 3 piece partition with return panel Curbside: 41ABS 18 drawer cabinet 3803A Rack Streetside: 462 Storage cabinet 1824 Locking cabinet 3802 Rack Door trays in rear door Roof vent and pilot switch Heavy duty cargo floor mat UP 5C Nevlen Package #1 for Information Technologies #P456 3 piece partition #P89 Return panel #P52 Writing desk Curbside: #41 18 drawer steel cabinet (with 41S mounting legs), facing front of van #E-9 Rack Streetside: #44 Spare tire rack #184 Combination rack #G1 Gas meter rack #26 DHB Roof Rack & #265 DHB Roof Rack (for 3 bar configuration) #39E Electric roof vent #39 NSE Pilot Switch Heavy Duty Cargo Floor Mat Wt. 369 lbs Wt. 345 lbs Wt. 611 lbs UP 5D Nevlen Package #2 for Information Technologies #P456 3 piece partition #P89 Return panel #P46C File pouch Revised May, 2014 16
Curbside: #45 18 drawer cabinet #E-9 Rack Streetside: #44 Spare tire rack #E-12 rack #464 4 drawer cabinet #E-70 rack w/e10sa door #26 DHB Roof Rack #39E Electric roof vent #39 NSE Pilot Switch HD Cargo Floor Mat UP 5E Nevlen Package for Engineering Services #P456 3 piece partition #P52 Steel writing desk Curbside: #184-1 Combination rack Streetside: #44 Spare tire rack #184 Combination rack #29 Field manual book rack 3000 watt Inverter #51 vise bracket #47B Swivel hooks #39E Electric roof vent #39 NSE Pilot Switch HD Cargo Floor Mat Wt. 497 lbs Wt. 850 lbs UP 5F Van Interior Package for Telecom Bulkhead Open Cabinet with Bin Van Shelf Unit Secure Storage with Door Hard Hat Bracket Cable Reel Holder Parts Cabinet 18 Bin Secure Storage Shelf Fire Extinguisher Bracket First Aid Kit with Tray Literature Holder Quick Rack, Curb Only 3,000 Watt Inverter UP 51.1 Ladder Rack for Compact Van UP 51.2 Ladder Rack for Full Size Van Wt. 30 lbs Wt. 45 lbs TRAILER TOWING PACKAGES THREE STEP PROCESS FOR CHOOSING A TRAILER TOWING PACKAGE 1.) Know the maximum weight of the trailer and cargo that you intend to tow. 2.) Pick a towing package that exceeds the maximum weight of the trailer and its cargo. 3.) Choose a vehicle spec from the ones recommended for that towing package. Remember, the loaded weight of the vehicle that you choose plus the loaded weight of the trailer should not exceed the GCWR for that vehicle spec. GCWR (Gross Combination Weight Rating) is the combined weight of the towing vehicle, occupants, trailer and cargo (vehicle and trailer cargo). Revised May, 2014 17
UP 6A 48,000 lb towing package (for 8817 Tractor) Receiver tube recessed below frame at rear reinforced to frame. Mount 24" from the ground to the bottom of the receiver hitch Combination ball/pintle hitch with 2 5/16 ball mounted on receiver insert. SAE Seven (7) flat blade light plug receptacle wired per industry standard. Requires chassis provision for electric brake controller, air brakes, and electrical lines to rear of frame 48,000 lb capacity (trailer and its cargo). Vertical Load = 6,000 lbs. Wt. 100 lbs UP 6B 16,000 lb towing package (Medium Duty) Receiver tube recessed in or under bumper and reinforced to frame. Combination ball/pintle hitch with 2 5/16 ball mounted on receiver insert. SAE Seven (7) flat blade light plug receptacle wired per industry standard. Requires chassis provision for electric brake controller 16,000 lb capacity (trailer and its cargo). Vertical Load = 3,000 lbs. Wt. 100 lbs UP 6C 50,000 lb towing package (Spring Loaded) (Heavy Duty) Receiver tube recessed in or under bumper and reinforced to frame HD pintle hitch mounted on receiver insert. SAE Seven (7) flat blade light plug receptacle wired per industry standard. Electric trailer brake controller. Requires chassis provision for electric brake controller 50,000 lb capacity (trailer and its cargo) Vertical Load = 6,000 lbs. Wt. 100 lbs UP 6D Air brake connections to end of frame. Gladhands mounted in fixed vertical position placed at each upper corner of the pintle hitch plate. Specify this option when you need to pull a trailer equipped with air brakes. The truck will be able to pull air or electric braked trailers Wt. 85 lbs UP 6E 10,000 lb towing package (Class IV) for pickups and SUV s Combination pintle/ball hitch with 2 5/16 ball mounted on receiver insert. SAE Seven (7) flat blade light plug receptacle wired per industry standard. 10,000 lb capacity (trailer and its cargo) Vertical Load = 1,000 lbs Wt. 100 lbs UP 6F 10,000 lb towing package (Class IV) for vehicles with service bodies Receiver tube recessed in or under bumper and reinforced to frame Combination pintle/ball hitch with 2 5/16 ball mounted on receiver insert. SAE Seven (7) flat blade light plug receptacle wired per industry standard. Electronic trailer brake controller if not supplied by chassis manufacturer 10,000 lb capacity (trailer and its cargo) Vertical Load = 1,000 lbs Wt. 100 lbs UP 6G 100,000 lb towing package HD pintle hitch mounted to 1 steel buck plate SAE Seven (7) flat blade light plug receptacle wired per SAE standard 560. Electric trailer brake controller, Requires chassis provision for electric brake controller 100,000 lb capacity (trailer and its cargo) Rear buck plate to include pintle hitch adjustment holes Vertical Load = 20,000 lbs. Wt. 250 lbs UP 6H 17,000 lb towing package for Pickups HD trunnion bar weight distributing hitch to include draw bar and 2 5/16 ball Distributes weight between the tow vehicle and the trailer wheels 17,000 lb capacity (trailer and its cargo) Vertical Load = 1,700 lbs Wt. 100 lbs Revised May, 2014 18
UP 6J 25,000 lb capacity under floor gooseneck hitch system with 2 5/16 ball, hinged access door to cover gooseneck box when not use. UP 6K 5,000 lb towing package (Class III) 2 ball mounted on receiver insert. SAE Seven (7) flat blade light plug receptacle wired per industry standard. 5,000 lb capacity (trailer and its cargo) Vertical Load = 5,000 lbs Wt. 15 lbs HYRAIL UP 7C Aires AT 1200 hyrail or equivalent with steel wheels Insulated design Hydraulic operation Hydraulic power is supplied by PTO with manual transmission models and an electrically operated pump with automatic transmission models Air over hydraulic disc type brakes on front gear Grip strut running boards Cross arm type lug wrench 2 driving lights, mounted on front bumper 2 driving lights, mounted on rear bumper Rail shunts Relay system to allow side to side shunt, front corner to opposite rear corner shunt Backup alarm w/timer that shuts the back alarm off in 10 seconds and reactivates with the brake. FRA Hyrail Inspection and Maintenance Log Packet Include an approved hyrail wheel wear gauge Part #02799ABF Wt. 900 lbs Revised May, 2014 19
UP 7D DMF RW 1630 hyrail or equivalent with steel wheels Insulated design Hydraulic operation Hydraulic power is supplied by PTO Air actuated Cobra type brakes Remote locking pin release 2 driving lights, mounted on front bumper 2 driving lights, mounted on rear bumper Rail shunts Relay system to allow side to side shunt, front corner to opposite rear corner shunt Backup alarm w/timer that shuts the back alarm off in 10 seconds and reactivates with the brake. Additional access steps to cab FRA Hyrail Inspection and Maintenance Log Packet Folding cab steps (Includes reversing transmission on spec 8213 with automatic transmission) Include an approved hyrail wheel wear gauge Part # 02799CBF or Part #02799DBF as applicable Wt. 2,150 lbs UP 7E Removable Shunts Wt. 8 lbs Revised May, 2014 20
UP 7F Hydraulic hyrail with steel tread wheels (Except Spec 0602 & 0603 receive rubber wheels) and automotive sealed hub and bearing assembly In-Cab controls for raising and lowering railgear 5 225/70R19.5F Tires (3-Hwy front/2 mud & snow rear for 4x2 vehicles) (5-Mud & snow for 4x4 vehicles) Recalibrate speedometer Front rail sweeps Front & rear derail skids 12 gauge tread plate covers over front & rear rail gear Grip strut running boards (Standard on all specs) Breaker bar & socket lug wrench 6 Ton hydraulic jack 2 driving lights, mounted on front bumper 2 driving lights, mounted on rear bumper with cutouts Rail shunts (2 front and 2 rear with switch in cab) Relay system to allow side to side shunt, front corner to opposite rear corner shunt Holder for hyrail lifting bar (mounted on front hyrail) Backup alarm w/timer that shuts the back alarm off in 10 seconds and reactivates with the brake. Add one or two rear springs to truck Four wheel alignment and rear thrust angle alignment Re-aim headlights prior to shipping truck FRA Hyrail Inspection and Maintenance Log Packet Include an approved hyrail wheel wear gauge Part #02799BBF Wt. 770 lbs Revised May, 2014 21
UP 7G DMF RW 1420 hyrail or equivalent with steel wheels Insulated design Hydraulic operation Hydraulic power is supplied by PTO Air actuated Cobra type brakes Remote locking pin release 2 driving lights, mounted on front bumper 2 driving lights, mounted on rear bumper Rail shunts Relay system to allow side to side shunt, front corner to opposite rear corner shunt Backup alarm w/timer that shuts the back alarm off in 10 seconds and reactivates with the brake. Additional access steps to cab FRA Hyrail Inspection and Maintenance Log Packet Folding cab steps (Includes reversing transmission on spec 8213 with automatic transmission) Include an approved hyrail wheel wear gauge Part # 02799CBF or Part #02799DBF as applicable Wt. 2,150 lbs UP SHUNT Shunt test connections: add wiring to shunt system with connections in cab for attaching a voltmeter. Wt. 2 lbs Revised May, 2014 22
UP 8 Ramsey REP8000RX Electric Winch Must be rear mounted if ordered with hyrail. 8000# Line pull 150 of 5/16 cable Grille guard mount ELECTRIC WINCH Wt. 95 lbs TOOL CHESTS UP 9 Cross mount tool box, one piece top opening lid. Includes bed mounted access steps on driver & passenger side. Full size pickup: 17.5 cu. ft. capacity Wt. 173 lbs UP 9A Floor mount chest type tool box, one piece top opening lid. Includes bed mounted access steps. Includes bed mounted access steps on driver & passenger side. 14 cu. ft. capacity Wt. 102 lbs UP 9B Full length side mount tool boxes, one pair. Includes bed mounted access steps on driver & passenger side. Revised May, 2014 23
11 cu. ft. capacity Wt. 140 lbs UP 9C Cross mount tool box, one piece top opening lid. Compact pickup: 7.75 cu. ft. capacity Wt. 112 lbs PULL-OUT TOOL DRAWERS Bolt to floor of van, pickup box, service body or utility vehicle. Available in three sizes. UP 9D1 Weatherguard Pack Rat #301 30 ¼ W x 24 D x 12 H, 3 compartment, 9 divider. Wt. 169 lbs UP 9D2 Weatherguard Pack Rat #303 40 ¼ W x 24 D x 12 H, 4 compartment, 12 divider. Wt. 224 lbs UP 9D3 Weatherguard Pack Rat #338 40 ¼ W x 48 D x 12 H, 4 compartment, 28 divider. Wt. 383 lbs Revised May, 2014 24
UP 9D4 Weatherguard Pack Rats (2) ea #305 10 1/4" W x 48"D x 9"H, 1 compartment, 7 dividers Wt. 220 lbs UP 9D5 Weatherguard Pack Rat #308 39 5/8"W x 48"D x 9"H, 4 compartment, 25 dividers Wt. 330 lbs UP 9D6 Weatherguard Pack Rat #307 29 7/8 W x 48 D x 8 7/8 H, 3 compartments, 19 dividers Wt. 247 lbs UP 9E Test Instrument Storage: Two 4-drawer cabinets mounted in extended cab facing side doors. Deletes rear seat. One American Van MED-10 facing the driver side and one American Van MDU-10 facing the passenger side Wt. 102 lbs UP 9F Full length side mount tool boxes with side opening doors that swing down 16 H x 12.5 D x 48 L, one pair. Mounted with cross bed toolbox raised to same height. 10.5 cu. ft. capacity Wt. 140 lbs Revised May, 2014 25
CRANES NOTE: Other makes and models of cranes may be substituted if approved by UPRR. All cranes rated 10,000 # and above must have annual wire rope inspection prior to delivery. A safety cone holder must be provided on all trucks equipped with a crane. Boom rests for telescoping cranes must have space for the cable to rest (such as a rubber block with a recess for the cable). UP 10A Econoton II R Telescopic Crane Available with UP 1A, UP 1AD & UP 1C services bodies Crane reinforcement required Short pedestal crane, curbside rear corner mount 3 3 Boom with extension to 5 2 Capacity 500 lbs. at 5 2 Power rotation, manual elevation and manual extension Pendant remote control High speed winch Spring-retractable jackleg Wt. 275 lbs UP 10AL Econoton II R Telescopic Crane Available with UP 1B service body, or platform bodies Long pedestal crane, curbside floor mount 3 3 Boom with extension to 5 2 Capacity 500 lbs. at 5 2 Power rotation, manual elevation and manual extension Pendant remote control High speed winch Spring-retractable jackleg (removable jackleg on pickups) Wt. 275 lbs Revised May, 2014 26
UP 10B IMT 1015 Telescopic Crane Available with UP 1AD or UP 1C Service bodies UP CR Crane reinforcement required Short pedestal crane, curbside rear corner mount 7 Boom with extension to 15 Capacity 1440 lbs. at 7, 720 lbs. at 15 Power rotation, elevation and extension (last extension manual) Proportional pendant remote control Single sheave block, High speed winch Stowed boom indicator and warning system Spring-retractable jackleg ANSI Crane Inspection Wt. 660 lbs UP 10BE Auto Crane 3203 (electric), for trucks without a PTO on the transmission. Replaces UP 10B ANSI Crane Inspection UP 10C IMT 5020 Telescopic Crane Available in lieu of standard, IMT 3816 Short pedestal crane, curbside rear corner mount 11 Boom with extension to 20 Capacity 4500 lbs. at 11, 2400 lbs. at 20 Power rotation, power elevation and extension (last extension manual) Proportional pendant remote control Single sheave block High speed winch Stowed boom indicator and warning system Hydraulic down/out jacklegs fixed streetside, horizontal extension curbside ANSI Crane Inspection NOT AVAILABLE WITH HYRAIL Wt. 1,825 lbs Revised May, 2014 27
UP 10D National 228 Telescopic Crane Available rebuilt only Center mount behind cab Tilting front and removable rear boom rests 16 Boom with extension to 28 Capacity 3350 lbs. at 16, 1700 lbs. at 28 Dual manual controls at crane Power rotation, elevation and extension Single sheave block Winch with anti-two block Hydraulic capacity alert system Stowed boom indicator and warning system Hydraulic down/out jacklegs horizontal extension both sides ANSI Crane Inspection Wt. 3,860 lbs UP 10E National 337 Telescopic Crane Center mount behind cab Tilting front and removable rear boom rests 16 Boom with extension to 37 Capacity 5200 lbs. at 16, 1500 lbs. at 35 Dual manual controls at crane Power rotation, elevation and extension Single sheave block Winch with anti-two block Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic A frame outriggers ANSI Crane Inspection (Currently not used) Wt. 7,325 lbs For NATIONAL 437 CRANE instead of 337 see spec UP 10K. Each application must be reviewed due to increased weight and cost of crane. UP 10F National 638C Telescopic Crane NOT available with hyrail-too unstable Center mount behind cab Front boom rest must be able to open tilt forward hood 16 Boom with extension to 38 Capacity 12,150 lbs. at 16, 4,450 lbs. at 35 Dual manual controls at crane Power rotation, elevation and extension LB2-3 two and three part line block Winch with anti-two block Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic A frame outriggers Hydraulic rear stabilizers Foot pedal throttle ANSI Crane Inspection Wt. 13,000 lbs Revised May, 2014 28
UP 10G IMT 11/76 -- Articulating Crane Center or rear mount must specify Folds into Figure 4 for storage Three hydraulic extensions to 31 6 Capacity 6,835 at 14 5, 2,050 at 31 6 Dual manual controls at crane Radio proportional remote control with docking station and warning buzzer. Buzzer to sound for seconds after parking brake is released. Docking station to charge remote control battery. Power rotation, elevation and extension Gunnebo cast safety clip hook Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic down/out jacklegs horizontal extension both sides ANSI Crane Inspection Wt. 3,415 lbs UP 10H IMT 14/98 - Articulating Crane Center or rear mount must specify Folds into Figure 4 for storage Hydraulic extension to 27 3 Capacity 10,580 at 6 2, 3,395 at 27 3 Dual manual controls at crane Radio proportional remote control with docking station and warning buzzer. Buzzer to sound for seconds after parking brake is released. Docking station to charge remote control battery. Power rotation, elevation and extension (Gunnebo cast safety clip hook Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic down/out jacklegs horizontal extension both sides ANSI Crane Inspection Wt. 3,195 lbs Revised May, 2014 29
UP 10J Northshore 1010 Loader Style Articulating Crane Center or rear mount must specify 20 Boom with extension to 23 6, Stows @ 22 (Except spec 8225 = 22 Boom with extension to 25 stows at 22 ) Capacity: 10,000 lbs at 12', 6,000 lbs at 20', 4,200 lbs at 23' 6" Seated controls atop crane mast, dual hand controls and foot controls Railing around platform to protect operator Front railing and swing pedal guard to protect operator Power rotation 650 degree, elevation and extension Gunnebo cast safety clip hook 10U Grapple Stowed boom indicator and outrigger warning system Hydraulic down and out outriggers, with dual load charts if not stable on rail Dual access ladders with grab handles and modified lower step for hyrail Ladder to platform clearance to allow rail storage Wide ladders with grip strut ladder tread non slip Grab handles on ladders and platform Load check valves on all cylinders Cylinder guards Hydraulic tubing guard on boom Operator seat belt Counter balance holding valves on all cylinders Triple stacked pump ANSI Crane Inspection Wt. 5,190 lbs UP 10K National 437 Telescopic Crane Center mount behind cab Removable rear boom rests 16 Boom with extension to 37 Capacity 20,000 lbs. at 4, 2,800 lbs. at 35 Dual manual controls at crane Power rotation, elevation and extension LB2-3 two and three part line block Winch with anti-two block Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic A frame outriggers Auxiliary outriggers mounted at the rear of the body ANSI Crane Inspection Wt. 8,000 lbs (add 800 lbs with auxiliary outriggers) UP 10L IMT 17/117 - Articulating Crane for Spec 8219, 8220 Rear mount Folds into Figure 4 for storage Hydraulic extension to 27 3 Revised May, 2014 30
Maximum capacity 14,460 lbs Capacity 7,960 at 14 2, 4,080 at 27 3 Hydraulics reels/valves to boom end for grapple, four functions(do not include on spec 8504, or 8604) Dual manual controls at crane Radio proportional remote control with docking station and warning buzzer. Buzzer to sound for seconds after parking brake is released. Docking station to charge remote control battery. Power rotation, elevation and extension Gunnebo cast safety clip hook Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic down/out jacklegs horizontal extension both sides ANSI Crane Inspection Wt. 3,500 lbs UP 10M IMT 30/217 - Articulating Crane for Spec 8119, 8120 Center mount Folds into Figure 4 for storage Hydraulic extension to 40 8 Maximum capacity 23,040 lbs Capacity 13,010 at 14 9, 4,210 at 40 8 Dual manual controls at crane Radio proportional remote control with docking station and warning buzzer. Buzzer to sound for seconds after parking brake is released. Docking station to charge remote control battery. Power rotation, elevation and extension Gunnebo cast safety clip hook Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic down/out jacklegs horizontal extension both sides ANSI Crane Inspection Wt. 5,800 lbs UP 10N National 649ETM Telescopic Crane NOT available with hyrail-too unstable Center mount behind cab, tractor mount Front boom rest must be able to open tilt forward hood 16 to 49 four section boom Capacity 13,650 lbs. at 16, 4,100 lbs. at 40 Dual manual controls at crane Power rotation, elevation and extension LB2-3 two and three part line block Winch with anti-two block Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic A frame outriggers Hydraulic rear stabilizers Foot pedal throttle ANSI Crane Inspection Wt. 11,000 lbs UP 10O IMT 2020 Telescopic Crane Horizontal reach to 20 0 Max Lift Capacity 5,000 lbs at 3 6 Power rotation, power elevation and extension One hydraulic extension, one manual extension Proportional pendant remote control Single sheave block High speed winch Revised May, 2014 31
Stowed boom indicator and warning system Hydraulic down jackleg fixed curbside ANSI Crane Inspection Wt. 920 lbs UP 10P IMT 5525 Telescopic Crane (Spec 6107) Horizontal reach to 24 10 Max Lift Capacity 10,500 lbs at 3 6 Power rotation, power elevation and extension Two hydraulic extensions Proportional pendant remote control Single sheave block High speed winch Stowed boom indicator and warning system Hydraulic down jackleg fixed curbside ANSI Crane Inspection Wt. 2,350 lbs UP 10Q IMT 2820 Telescopic Crane (Spec 6602, 7401, 8401) Horizontal reach to 20 6 Max Lift Capacity 5,000 lbs at 3 9 Power rotation, power elevation and extension Two hydraulic extension Proportional pendant remote control Single sheave block High speed winch Stowed boom indicator and warning system Outrigger stow alarm Hydraulic down jackleg fixed curbside ANSI Crane Inspection UP 10AA IMT 3820 Telescopic Crane (Spec 6107, 8301, 8401) Horizontal reach to 20 6 Max Lift Capacity 7,500 lbs at 3 9 Power rotation, power elevation and extension Two hydraulic extension Proportional pendant remote control Single sheave block High speed winch Stowed boom indicator and warning system Hydraulic down jackleg fixed curbside ANSI Crane Inspection Wt. 1,400 lbs Wt. 1,460 lbs Revised May, 2014 32
UP 10AB IMT 10/65 -- Articulating Crane (Spec 8509, 8609) Center or rear mount must specify Folds into Figure 4 for storage Three hydraulic extensions to 30 2 Capacity 4,859 at 12 6, 1,920 at 30 2 Dual manual controls at crane Radio proportional remote control with docking station and warning buzzer. Buzzer to sound for seconds after parking brake is released. Docking station to charge remote control battery. Power rotation, elevation and extension Gunnebo cast safety clip hook Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic down/out jacklegs horizontal extension both sides ANSI Crane Inspection Wt. 2,710 lbs UP 10AC IMT 13/88 -- Articulating Crane (Spec 8509, 8609) Center or rear mount must specify Folds into Figure 4 for storage Three hydraulic extensions to 30 2 Capacity 4,859 at 12 6, 1,920 at 30 2 Dual manual controls at crane Radio proportional remote control with docking station and warning buzzer. Buzzer to sound for seconds after parking brake is released. Docking station to charge remote control battery. Power rotation, elevation and extension Gunnebo cast safety clip hook Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic down/out jacklegs horizontal extension both sides ANSI Crane Inspection Wt. 2,710 lbs UP 10AD IMT 425AT specialty crane - no exceptions 25'2" boom extension Capacity 4200# @ 9'3"; 1350# @ 25'2" Dual manual proportional controls Corner mount Capacity alert system Crane hook Boom and outrigger stow alarm PTO interlock NOTE: Winch is an option Weight with winch Wt. 2,100 lbs Wt. 3,200 lbs UP 10AF National 690E2 Telescopic Crane NOT available with hyrail-too unstable Center mount behind cab Front boom rest must be able to open tilt forward hood 27 to 90 four section boom Capacity 14,750 lbs. at 16, 3,850 lbs. at 45 Dual manual controls at crane Power rotation, elevation and extension LB2-3 two and three part line block Winch with anti-two block Hydraulic capacity alert system Stowed boom indicator and outrigger warning system Hydraulic A frame outriggers Hydraulic rear stabilizers Revised May, 2014 33
Foot pedal throttle ANSI Crane Inspection Wt. 13,180# UP 10AG IMT 5005i Telescopic Crane Horizontal reach to 16 Max Lift Capacity 5,000 lbs at 6 Power rotation, power elevation and extension One hydraulic extension Proportional pendant remote control Single sheave block High speed winch Stowed boom indicator and warning system Hydraulic down jackleg fixed curbside? ANSI Crane Inspection Wt. 920 lbs CRANE ACCESSORIES UP 10R Proportional remote control Available with UP 10D, UP 10E, UP 10F (Included with all other cranes except UP 10J) Wt. 20 lbs UP 10R1 Radio remote control, Radio remote control docking station and warning buzzer. Buzzer to sound for seconds after parking brake is released. Docking station to charge remote control battery. Wt. 15 lbs UP 10S Magnet with hydraulically driven generator, 30 magnet for 300 and 400 series cranes 38 magnet for 600 series cranes. Includes a magnet hanger bracket on grapple to allow the magnet to be picked up without removing the grapple. With electric reel on crane, separate hydraulic system to run generator. Order grapple spec UP 10U. Wt. 1,085 lbs UP 10T 1/3 Yard clamshell bucket, Include hydraulic reel mounted on telescopic cranes. With Additional valve 26 wide, Fits between rails Wt. 540 lbs UP 10T-1 4/5 Yard clamshell bucket, Include hydraulic reel mounted on telescopic cranes. With Additional valve 47 wide. Wt. 680 lbs UP 10U 1/3 Cord grapple, 280 degree rotation with former Spec 65 only, open tine is 70 or greater with straight tine ends. Grapple tines made of A514 T-1 steel. Include hydraulic reel mounted on telescopic cranes, with additional valve included with UP 10J crane. Wt. 705 lbs UP 10V Single man basket option for 300 and 400 series cranes. Wt. 250 lbs UP 10W Winch for Crane Available with UP 10G or UP 10H cranes (Included with all other cranes except UP 10J) Wt. 200 lbs UP 10X Pallet Forks, Kinshofer KM 415 or equal, Vertical member adjustable from 41 to 55 38.5 long forks. Fork with adjustable from 13 to 37 5,500 lb capacity. Wt. 350 lbs Revised May, 2014 34
UP 10Y Two man single compartment basket 1,000# capacity Wt. 210 lbs Grapple and clamshell options include a rotator if the crane does not have a winch HYDRAULIC TOOL CIRCUIT & HEATERS UP 11 Hydraulic tool circuit (Tool circuit must conform to HTMA Railroad Hydraulic Circuit guidelines) Must have at minimum a flow control meter, temperature gauge, pressure gauge Built into a lockable control panel, Must have dual fan cooler system with temperature controlled system that allows fan to shut down in cold weather; must also have bypass valve for cold weather operation, Includes a 50 spring retractable hose reel and hose connected to a selected 5 or 10 gallon per minute circuit. An additional 50 of hose furnished for use as a jumper hose or for connection to an additional 5 gallon per minute circuit. Wt. 350 lbs UP 11-1 Coolant heater for hydraulic system UP 11-2 Diesel fired engine heater and coolant heater for hydraulic system UP 11-3 Diesel fired cab heater only UP 11A Delete hydraulic hose reel and hoses UP 11B Hydraulic hose reel only with 8 jumper hose Wt. 20 lbs Wt. 25 lbs Wt. 100 lbs Wt. -125 lbs Wt. 135 lbs UP 11C Webasto Air Top 2000 pickup bed heater, thermostatically controlled For use on a pickup with a cap, lid, or cover Wt. 6 lbs UP DEL 11 Delete standard hydraulic tool circuit & supply add hydraulic power unit rack with hydraulic reel & hoses so a hydraulic power pack can be mounted on the truck to operate hydraulic tools Wt. -350 lbs BED MAT UP 12 Bed Mat, Heavy Duty (for pickup bed floor), this is not a bedliner. Wt. 50 lbs Revised May, 2014 35
AIR COMPRESSOR UP 13 CAS435HA Hydraulic Air Compressor; Four cylinder, single stage 35 cfm @ 100 psi Hydraulically driven Dimensions: 24"W x 47.75"L x 20.62"H Includes: 50 retractable hose reel with 3/8 ID air hose and quick coupler Wt. 200 lbs UP 13A Underhood VMAC Rotary Air Compressor 70 cfm @ 175 psi Air/oil separator tank Liquid to liquid oil cooler Engine throttle control Includes: 50 retractable hose reel with 1/2 ID air hose and quick coupler Wt. 200 lbs PLATFORM BODIES FOR 8 TO 12 BODIES HD platform body with 3/16 smooth steel floor, Cross sills on 12 centers, made of minimum 10 gauge steel with 4 depth. Side and end rails of 10 gauge steel and 6 depth. Longitudinal sills to be reinforced with front, rear and intermediate gussets Flush mounted tail and clearance lights. Full depth stake pockets on 24 centers. Rear anti-sail mud flaps. Body painted to match chassis; decks, access steps, and grab handles painted with nonskid, abrasive paint. Steel, OSHA type bulkhead 42 high with screened window, unless body is mounted behind a crane: then bulkhead will be of sufficient height to protect crane controls and operator. Spare tire (if so equipped) mounted to bulkhead with lock. Full width step type treadplate bumper meeting all ICC and DOT regulations with reinforcement for a pintle hitch, A lining bar compartment is built into the bumper on all 12 and longer platform bodies. Grab handles at side step and rear step. FOR 14 TO 20 BODIES Extra HD construction as follows: 7 gauge end and side rail material, 7 x 9.8 lb per ft structural channel long sills, 5 x 6.7 lb per ft structural channel cross sills, cross sills on 12 centers, 3/16 treadplate floor. UP 14A 8 L x 6.5 W UP 14B 9 L x 8 W Wt. 800 lbs Wt. 985 lbs Revised May, 2014 36
UP 14C 12 L x 8 W UP 14D 14 L x 8 W UP 14E 16 L x 8 W UP 14F 18 L x 8 W UP 14G 20 L x 8 W UP 14P 22 L x 8 W Wt. 1,900 lbs Wt. 2,500 lbs Wt. 2,800 lbs Wt. 3,260 lbs Wt. 3,600 lbs Wt. 3,940 lbs DUMP BODIES UP 14H 12 Yard Dump Body (end dump), 15 long. 3/16 hi-tensile steel floor and tailgate. 10 gauge sides. Full length horizontal side brace. Sloped running boards. ½ cab shield. Heil HPT63-130 or equal telescopic hoist. Air shift PTO, pump and lever control. Body raise light. Safety prop. Lights, reflectors, markers and mud flaps per DOT regulations. Amber strobe light with self-leveling bracket mounted on cab shield. Paint body to match cab. Please note on order if tarp mechanism is needed. Wt. 5,900 lbs UP 14I Side dump body, 178 L x 96 W. 32 H front and rear bulkheads. 26 H side dump gates, top or bottom opening. 165 L x 90 W interior length. All steel construction. ¼ plate floor. 177 L subframe. Twin dump cylinders mounted at the front and rear of the body. Pin release at all corners to dump to street or curbside. Please note on order if tarp mechanism is needed. Wt. 3,535 lbs UP 14J Rotary dump body, 168 L x 84 W inside dimensions. All steel body, 40 H sides. HD dump bed with ¼ steel floor, 10 ga. Steel sides. 3 structural steel crossmembers, 5 x2 x0.25 tubular long sills. 46 H tailgate with ¼ steel apron, 30 L full body width. Mounts atop sub-frame to rotate and dump. Hoist and rotational mechanism is fully hydraulic. Rear anti-sail mud flaps. Rail Clamps. Body painted to match chassis. Please note on order if tarp mechanism is needed. Wt. 7,000 lbs UP 14K Under Body Compartments: Curbside Horizontal compartments: 2 adjoining compartments. Each is 52W x 20H x 18D. Bottom hinged doors. Roll out tray w/ 6" high dividers on 4" centers located on floor of forward compartment. Vertical access ladder with hand rails located aft of horizontal compartments. Streetside: Horizontal compartments: two adjoining compartments. Each is 52W x 20H x 18D. Bottom hinged doors. Roll-out tray with 6" high dividers on 4" enters Located on floor of forward compartment. Vertical access ladder with hand rails located aft of horizontal compartments. DUMP BODY ACCESSORIES UP 14L Snow Plow (sized to fit application) Provide override system to protect pumping system due to low oil or high oil temperature. System will shut down at 158ºF. Install skid shoes. Revised May, 2014 37
UP 14M Sand/salt spreader (sized to fit application) Provide override system to protect pumping system due to low oil or high oil temperature. System will shutdown at 158ºF. UP 14N 12" asphalt lip bolted on PLATFORM BODY ACCESSORIES UP 15A Steel stake racks, 42 high, interlocking, 15A 8 = 272 lbs Painted to match body/cab, 15A1 9 = 306 lbs Wt. (per foot of body length) 34 lbs 15A2 12 = 408 lbs 15A3 14 = 476 lbs 15A4 16 = 544 lbs 15A5 18 = 612 lbs 15A6 20 = 680 lbs 15A7 22 = 748 lbs UP 15B Wood sideboards and end board, 12 high. 15B 8 = 136 lbs Removable and interlocking 15B1 9 = 153 lbs Wt. (per foot of body length) 17 lbs 15B2 12 = 204 lbs 15B3 14 = 238 lbs 15B4 16 = 272 lbs 15B5 18 = 306 lbs 15B6 20 = 340 lbs 15B7 22 = 374 lbs UP 15C 14" high removable interlocking steel side boards 15C 8 = 80 lbs and end boards. Rectangular tube 15C1 9 = 90 lbs pockets welded to crossmember with square 15C2 12 = 120 lbs tube stake and spring locks at stake pockets. 15C3 14 = 140 lbs Includes 2 square tube perimeter frame 15C4 16 = 160 lbs construction, 3 steel side boards per side with 15C5 18 = 180 lbs 3 stakes per side board. 2 piece tailgate, 15C6 20 = 200 lbs interlocking side boards and tailgates. (per 15C7 22 = 220 lbs foot of body length) 10 lbs Painted to match body/cab UP 15C1 Tie Rack - 10 tie post tubes 2.5"x2.5"x54" that slide into the side holders. Includes a bolt in tie post rack at front bulkhead with tie rings for storage of posts. UP 15D Underbody storage boxes, pair (24 L x 18 H x 18 ) UP 15D1 Underbody storage boxes, pair (30 L x 18 H x 18 ) Wt. 120 lbs. Wt. 134 lbs. Revised May, 2014 38
UP 15D2 Underbody storage boxes, pair (36 L x 18 H x 18 ) UP 15D3 Underbody storage boxes, pair (48 L x 18 H x 18 ) UP 15D4 Underbody storage boxes, pair (60 L x 18 H x 18 ) Wt. 148 lbs. Wt. 190 lbs. Wt. 230 lbs. Under body boxes will be sized to give maximum storage space to each truck UP 15E Above body storage box. Mounted next to bulkhead (96 x 16 H x 12 D) (78 L with UP 14A 8 body) UP 15E1 (60 L x 19 H x 21 D), 16 ga., for miscellaneous storage UP 15E2 (66 L x 42 H x 38 D), 10 ga., top opening. For hydraulic tool storage. Includes tool holders UP 15E3 Same as UP 15E2 but no tool holders UP 15E4 (42 L x 24 H x 18 D), Stackable, For B&B Dept UP 15E5 (48 L x 16 H x 18 D), Stackable, For B&B Dept UP 15E6 (98 L x 16 H x 18 D), Stackable, For B&B Dept UP 15E7 Gas Bottle Compartment (Removable), For B&B Dept. Wt. 195 lbs Wt. 200 lbs Wt. 385 lbs Wt. 380 lbs Wt. 165 lbs Wt. 155 lbs Wt. 305 lbs Wt. 325 lbs UP 15F 4 tie down winches (ratchet type) evenly spaced down the length of the body, 12,000 lb. capacity, 4 wide x 27 long nylon strap with flat hook. Wt. 120 lbs UP 15G Tie down rings, 6 per body, evenly spaced. UP 15H Hoist, 20 ton underbody. Allows platform body to dump (Available with UP 14C, D, E and F platform bodies) Wt. 24 lbs Wt. 1,000 lbs UP 15J Liftgate, 2,000 lb capacity. (Not available in combination with UP 15H or hyrail). Wt. 750 lbs UP 15J-44D Delete Liftgate, Add bulkhead Rack to storage accessory tray and rear bumper UP 15K Rail racks, Located at the front and rear of the body, Dual racks, four rail capacity (2 per side). Tie down chains (transport grade 70) and ratchet binders welded to uprights (4). Includes step(s) for operator to safely tie rail onto the front rack. Also includes ½ rubber pad on rail rest. Wt. 550 lbs UP 15L Timber racks, Located at the front and rear of the body, Dual rack. Tie down chains (transport grade 70) and ratchet binders welded to uprights (4). Includes step(s) for operator to safely tie timber onto the front rack. Wt. 550 lbs UP 15M Fall Protection/Lifetime System, for sides of trucks, Includes (1) 35 sureline, (2) 4 lanyards, attachment points and a storage box, Per UPRR guidelines Wt. 560 lbs UP 15N Rail Rack for (one) 28 rail, Front and intermediate racks with chain rail binders on each rack. Revised May, 2014 39
Except as noted, any accessory is available with any platform body WELDING MACHINES All welding machines to have an in cab On/Off switch except spec 7301 & 7401 UP 16A Miller Air Pak 400 amp DC (continuous) 500 amp DC (maximum) 40 CFM air compressor 120/240 volt single phase power 240 volt three phase power Duetz diesel engine Remote battery jumper system Meets UP track welding specification #AWT-400AC Wt. 2,500 lbs UP 16A1 Air dryer for compressor on UP 16A (C-R Turbo 2000 or equal) Wt. 20 lbs UP 16B Miller Trailblazer 302G 200 amp AC/DC/CC (at 60% duty cycle) 300 amp AC/DC/CC (at 100% duty cycle) Auxiliary power 9500 Watt continuous 120/240 Volt, 88 Amperes, 60 HZ Subaru 23 horsepower gasoline engine 50 of welding lead, ground clamp, electrode holder and storage bracket Cover for welder Wt. 568 lbs Revised May, 2014 40
UP 16C Miller Bobcat 250D 250 amp AC/CC and 210 amp DC/CC (at 100% duty cycle) Auxiliary power 8 KVA/KW (continuous) 120/240 Volt, 70 Amperes, 60 HZ Deutz-Ruggerini 16 horsepower diesel engine 50 of welding lead, ground clamp, electrode holder and storage bracket Cover for welder Wt. 650 lbs UP 16D Miller Wildcat 200 Gas Engine 150 amp DC/CC (at 100% duty cycle) Auxiliary power 5500 Watts (continuous) 120/240 Volt, 54 Amperes, 60 HZ Suburu 14 horsepower gas engine 50 of welding lead, ground clamp, electrode holder and storage bracket Cover for welder Wt. 350 lbs UP 16E Miller Extreme 195500 wire feed package (For Air Pak Spec 16A). Track-Weld, Inc. For 5/64 wire. Includes 400 amp Brack-Weld 12615RRM flux core gun. Wt. 30 lbs Revised May, 2014 41
UP 16F Enclosed Welder Platform. Curbside front compartment, Side opening, 24 W x 72 L x 48 H Slide out roller tray for welder UP 16G Trailblazer 302D 200 amp AC/DC/CC (at 60% duty cycle) 300 amp AC/DC/CC (at 100% duty cycle) Auxiliary power 4.5 KVA/KW maximum (4.0 KVA/KW continuous) 120/240 Volt, 30 Amperes, 60 HZ Kubota 19 horsepower diesel engine 50 of welding lead, ground clamp, electrode holder and storage bracket Cover for welder Wt. 720 lbs UP 16H Trailblazer 302 Air 280 amp DC/CC, 32 V (at 100% duty cycle) 200 amp DC/CC, 25 V (at 100% duty cycle) Auxiliary power 11,000 Watts continuous, maximum 13,000 watts 120/240 Volt, 100 Amperes, 60 HZ Kohler 30 horsepower gas engine 26 CFM, 100% Duty Cycle, 80-160 psi 450 Amp, 12 volt jump start 50 of welding lead, ground clamp, electrode holder and storage bracket Wt. 771 lbs UP 16J Miller 145 DX with GFI Wt. 310 lbs 145 amp DC/CC, 25V 20% Duty Cycle Auxiliary power 4,000 Watts continuous, maximum 4,500 watts 120Volt, 100 Amperes, 60 HZ Kohler 10 horsepower gas engine Revised May, 2014 42
50 of welding lead, ground clamp, electrode holder and storage bracket WORK PLATFORM UP 17 Steel and aluminum work platform, detachable, rear mounted. 31 x 72 with two strap binders Wt. 175 lbs ELECTRICAL POWER UP 18A 3000 Watt power inverter Wt. 55 lbs 120 Volt AC Power Auxiliary battery with isolator GFI outlet 35 cord reel (UP 18C Cord reel is not included on spec 2345, 3415, and 3455. It may be ordered as an option on these specs if needed.) Power switch in cab (lighted and labeled) (For Pickup installation - unit should be mounted under rear seat or shielded) UP 18C Cord reel, 35 of 12 gauge 3 conductor cable. 20 ampere capacity, single phase. Wt. 40 lbs UP 18D Portable generator (for single phase power) Wt. 255 lbs Gasoline powered 5000W (5kw), 110VAC Electric start. Please specify on order if remote starting panel is needed and location. Revised May, 2014 43
UP 18E 3600 Watt power inverter 120 Volt AC Power Auxiliary battery with isolator GFI outlet 35 cord reel Power switch in cab (lighted and labeled) UP 18F Portable generator 3800 watt Gasoline powered Honda engine 120/240 volt Remote start Wt. 55 lbs Wt. 192 lbs UP 18G 1500 watt power inverter, 120V AC power with auxiliary battery Wt. 55 lbs RAIL LUBRICATORS UP 19A Robolube Model 240 or equal. Holds 250 lbs of grease. Mounts in pickup bed behind cab. Gauge face applicators. Wt. (with grease) 950 lbs Revised May, 2014 44
UP 19B1 Top of rail applicators for UP 19A and UP 19B (in addition to gauge face). Wt. 20 lbs UP 19C Sub-floor for Rail Lubricators. Raises Lubricator 6 above floor. Area under sub-floor is divided for lining bar and manual storage. Wt. 125 lbs Revised May, 2014 45
POLICE EQUIPMENT UP GG Ranchhand grill guard Wt. 70 lbs UP GUN UP GB-EX Vertical rifle & shotgun mount in between front driver/passenger seats with timer lock release Wt. 22 lbs TruckVault Gun Box T-FDEXRS1-11N-PS-SA Standard one drawer, spare access for Explorer Wt. 138 lbs UP GB-DR TruckVault Gun Box T-DGDURSI-IIN Standard one drawer for Durango Wt 183 lbs UP GB-TH TruckVault Gun Box T-CHTAHS1-07N Standard one drawer for Tahoe Wt. 177 lbs UP GB-PU TruckVault Gun Box T-DGRAMS2-09S-PC Standard two drawer for Short Bed Pickup Wt. 300 lbs UP PP Prisoner partition Wt.??? lbs UP PSRS Laguna prisoner seat and rear screen Wt??? lbs COMPANY RADIOS UP DM Dash mounted company radio Wt. 10 lbs Revised May, 2014 46
UP DH Dual Head company radio Wt. 10 lbs UP RM Remote Mount company radio Wt. 10 lbs Revised May, 2014 47
DECALS UP RD UP SD Rotational decals for Transportation Security/Police Decal Package MISCELLANEOUS EQUIPMENT UP 20 Ram Brand adjustable mount for laptop computer with Tripp Lite PV150-150 watt inverter power supply or equal. If vehicle is ordered with UP 18E inverter delete the Tripp Lite inverter and use the UP 18E inverter to power the laptop. UP 21 Telxon Model PTC-1194 mono transflective inventory management system (part #1194 UPIMD). Requires vehicle mounting base and related equipment (part #1194 UPIMD/VC). Wt. 50 lbs UP 22 NORDCO Model B Trak Inspector, Includes lightweight aluminum folding frames, sensing units for gage and cross level, clear view indicators for gage and cross level, adjustable buzzers for permissible gage limits with necessary electrical connections. Contact at NORDCO in Milwaukee, WI is Jeanmarie Steele (414-769-4600). Revised May, 2014 48
UP 23 UP 24 Jamar Distance Measuring Instrument Step n Seat Fold down steps with grab handles for hyrail pickup use. Constructed of a permanent mold cast aluminum alloy, which is heat treated for optimum strength; capacity is 400 pounds. Available on specs 2210, 2250, 2310, 2350, 2510, 2550, 3415, 3455 Wt. 38 lbs UP 25 Slide out, fold down steps with grab handles for hyrail pickups with a sub-floor. For use with UP 19C, Available on specs 2210, 2250, 2310, 2350, 2510, 2550 Wt. 60 lbs UP 42SB UP 44HT UP 46HR Removable storage box for hydraulic tools 14 H x 32 W x 46 L, 4 locking pins Removable storage box for hydraulic tools 21 H x 33.5 W x 49 L, Two web strap tie down binders. Oxy/Acetylene reel with 3/8 x 100 hose - grade T, to be located over hydraulic hose reel at the rear of the truck. UP ALARM1 UP ALARM2 Security system for a pickup cab only, includes sensors on all doors and a motion sensor on the vehicle, activated by a key fob. Security system for pickup cab and body; includes sensors on all cab doors and pin switches on all body doors, a motion sensor on the vehicle, activated by a key fob. UP ALARM3 Security system for a four door SUV which includes sensors on all doors and a motion sensor on the vehicle, activated by a key fob. Revised May, 2014 49
UP ALARM4 Security system for a Cargo Van which includes sensors on all doors and a motion sensor on the vehicle, activated by a key fob. UP 59-1-WK Wet Kit - 30,000 LB. capacity, Mechanical Drive Winch with positive slack adjuster, reinforced riser approximately 24 above truck frame, chain drive system to have adjustable idler with reinforced bracket cross mounted to both frame rails. Aluminum, protective covers for winch drive system. Automatic external, tensioning system, cable storage hooks to be located below walk area with swag eye storage ahead of fifth wheel. Transmission mounted air shift PTO, Roller assembly mounted at end of tractor frame for gooseneck operation with winch, and ramping behind fifth wheel. UP 59-1-W Frame mounted Winch - Transmission mounted Hotshift PTO and Hydraulic pump, Frame mounted hydraulic reservoir, Spin on hydraulic filter and shut off valve. Electrical control switches on both sides of headache rack to activate hydraulics from ground level. Indicator lights for hydraulic operation at each control location. Spring loaded hose reel with 25 Siamese hose, protective jacket, quick couplers and ballstop. UP 65V There must be three electronic dump valves one on each section of the stacked pump, which controls the left hand, right hand, and foot controls. The valves to be sized correctly to match the flow rates with minimum back-pressure and the return lines to be collected in a manifold and returned to tank with minimum backpressure. The emergency button is located on the crane controls, located and marked for easy understanding. All wiring to be in piping and weatherproof and fused through the power distribution panel on the ignition side of the controls UP 65-W Winch for Northshore 1010 boom Wt. 324 lbs UP BC UP BI Backup camera Bridge Inspector s Package - Includes UP TOP-2 with side opening doors on both sides, no side windows, sealed rear lift up gate, deletes driver side door opening, tool box, and dividers, includes goalpost style cargo/ladder rack with center support, and single ear on Revised May, 2014 50
curb side to keep ladder from sliding, UP 9D7 Weatherguard Pack Rat #334-3 (30-1/4 W x 49 D x 12 H) located driver side of bed, Spare tire mounted vertical passenger side rear, ¾ plywood platform covering bed space over wheel wells. Available on Spec 2240 & 2350 UP BR Bolt Rack UP BT UP CHP Bluetooth option aftermarket installation Hook & chain style hood prop - allows hood to tilt forward and remain secure without removing front rail rack Revised May, 2014 51
UP CENCON Modified center console for use in a medium or heavy crew cab with rear air conditioning and heating option. UP CTH UP DR UP WDR Concrete Tie Handler Chassis deflector rack, made of tubing front mounted with ability to lift hood. Vendor must supply FEA analysis and crash test data. Wulf s deflector rack & boxes Revised May, 2014 52
UP FS30 UP FS50 UP FS80 UP HTC 30 gallon water suppression system permanently installed under the truck body, Water faucet instead of ball valve, Pressurized by air diaphragm pump - 10 GPM flow rate. Tank includes opening or fitting for adding antifreeze or fire suppression additives. Check vehicle spec for correct tank size for each individual spec. 50 gallon water suppression system permanently installed under the truck body, Water faucet instead of ball valve, Pressurized by air diaphragm pump - 10 GPM flow rate. Tank includes opening or fitting for adding antifreeze or fire suppression additives. Check vehicle spec for correct tank size for each individual spec. 80 gallon water suppression system permanently installed under the truck body, Water faucet instead of ball valve, Pressurized by air diaphragm pump - 10 GPM flow rate. Tank includes opening or fitting for adding antifreeze or fire suppression additives. Check vehicle spec for correct tank size for each individual spec. Two hydraulic tool carriers, will hold spike driver or spike puller, one (1) large to the left side of bumper and one (1) small to the right side of bumper, Will pivot to allow easier access to the tools, includes tie down chains. UP JBH Joint bar holder Wt 22 lbs Revised May, 2014 53
UP JL Jimmy Lifter (Dual rail tong) Wt 300 lbs *The Jimmy Lifter is a dual rail tong lifting attachment that Jim Nudera designed with our engineers. It allows a piece of rail to be picked up at (2) points which allows for more stability when moving it. UP JUMPER Jumper cables (25 ) with receptacle on front bumper, 600 amp rating for 1000 through 5000 specs and 800 amp rating for 6000 through 8000 specs. Wt 14 lbs Revised May, 2014 54
UP LJS UP LS Locomotive Jumper System 70 2/0 jumpers on electric reel - battery hot, used to jump locomotives to each other Lubricator system to supply top of rail or flange grease from portable tote Top of rail Viking stainless pump with 1 ¼ x 30 reel Flange grease Viking pump with 1 ½ x 30 reel Shut off valve system Cam coupler control system for intake, 2 for top of rail, 3 for flange Oil cooler 20 gallon oil tank UP NET Screen partition with a detachable net in the middle for use with 2000, 3000, & 5000 series Extended Cab trucks, Cargo net for interior of 7000 series extended cab trucks. UP RC Rear mount IMT 17/117 articulating crane on spec 8104 or 8204. UP RH 2 Receiver Hitch UP RSD Rear seat delete UP RT Rail tong storage (Single) Wt 25 lbs Revised May, 2014 55
UP REGEN UP TC-A UP TC-B UP TC-C UP TC-D First Stage Regen Warning - When the Instrument Cluster regeneration warning light comes on the 1st time and stays on solid the exterior warning will consist of the electric horn sounding for 10 seconds consecutively. Second Stage Regen Warning - When the Instrument Cluster regeneration warning light starts flashing the exterior warning will consist of the electric horn sounding for 10 seconds consecutively and simultaneously the Turn Signals will start flashing in the same fashion as if the "Hazard Signal" had been turned on. The flashing lamps will continue until either a Manual Regen has been initiated and the ECM stops sending the Second Stage regen warning signal, the parking brake is released, or an ignition cycle. If the truck goes through an ignition cycle and the ECM is still sending the Second Stage Regen Warning, then the exterior warning should immediately begin again. (Supply with Peterbilt or Kenworth Spec 8817 and 8818 only) Telecom Package A: (Standard on all Telecom Orders) Includes: Power windows & door locks UP ALARM3 Security Alarm for pickups Telecom Package B: (Available on Telecom Orders Only) Includes: Power windows & door locks UP ALARM3 Security Alarm for pickups UP 8 8,000# electric winch Telecom Package C: (Available on Telecom Orders Only) Includes: Power windows & door locks UP ALARM3 Security Alarm for pickups UP 18A 3000 Watt power inverter Telecom Package D: (Available on Telecom Orders Only) Includes: Power windows & door locks UP ALARM3 Security Alarm for pickups UP 8 8,000# electric winch UP 18A 3000 Watt power inverter UP TKO (300 gallon aluminum oil tank ILO 130 gallon steel oil tank) (For Spec 6133 & 6333) Revised May, 2014 56
UP TKW UP Water UP WC UP WMP (300 gallon aluminum water tank ILO 130 gallon steel water tank) (For Spec 6133 & 6333) Battery Watering Option (Signal) 20 gallon plastic tank, 4 gpm pump, 25 hose reel external water fill, power switch, mount tank under body Wheel Check loose lug nut indicators Wire mesh partition behind rear seat UP WS UP WS1 UP WS2 UP YF UP YP The washdown system is a 33 gallon poly tank that is located between the cab and the body. It includes a city water intake fitting and (2) electric pumps in series for pressure. Include 40 feet of 3/4" diameter hose. (Weighing system with one (1) readout) (Weighing system with two (2) readouts) (Mechanical Yard Foreman Package UP 4D Work lights cab guard mounted, UP 4F Golight (or equal) remote controlled 100,000 CP halogen spotlight, UP 9A Floor mount chest type tool box one piece top opening lid, UP 9B Full length side mount tool boxes one pair, UP 12 Bed Mat Heavy Duty (for pickup bed floor), UP DM Dash Mount Company Radio) Pickup Intermodal Yard Package To include mount fire extinguisher inside pickup bed Driver side on bulkhead, LED red strobe lights mounted in rear bumper one each side; LED red strobe lights mounted in front bumper one each side; Replace top brake and stop light bulbs with led bulb; UP DR Chassis deflector rack, made of tubing front mounted with ability to lift hood; UP 4 Post mounted light; UP 6E less hitch, brake brake controller, and electric plug Van Intermodal Yard Package To include delete rear seat for 12 passenger capacity, mount fire extinguisher at rear driver side in tubing pocket, LED red strobe lights mounted in rear bumper one each side; LED red strobe lights mounted in front bumper one each side Replace top brake and stop light bulbs with LED bulb; Equipment storage tray approximately 8 H x 30 W x 30 D with tool bar holders; Storage rack to clip into seat brackets; UP DR Chassis deflector rack, made of tubing front mounted with ability to lift hood; UP 4 Post mounted light; UP 6E 10,000 lb towing package Class IV Revised May, 2014 57