Published 06/04 SWITCH BLADE 5 ft. & 6 ft. Sickle Bar Mower Model With Mechanical Break-A-Way PART'S MANUAL P/N 02974374P An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (830-379-1480) to obtain a Free copy before operating the equipment. ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas 78155 830-379-1480 2006 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain.
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Servis-Rhino Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas 78155 830-379-1480 2006 Alamo Group Inc. Parts Section - 1
Parts Section - 2 PARTS SECTION
PART NAME INDEX CARRIAGE ARM ASY - P/N 02974362... 8 COMMON COMPONENT BOX - 02974368... 9 CONTROL VALVE ASY - P/N 02974364... 10 CYLINDER ASY - BAR TILT - P/N 0693500A... 25 CYLINDER ASY - CURB LIFT - P/N 0693400A... 26 FILTER ASY - P/N 02974309... 12 HYDRAULIC TANK ASY - P/N 02974348... 13 KNIFE DRIVE ASY - P/N 02974300... 15 MOTOR ASY - P/N 02974301... 16 PUMP ASY - P/N 02974302 - S/N SWB-10361 (09-04) & DOWN... 21 PUMP ASY - P/N 02974302A - S/N SWB-10362 (10-04) & UP... 22 PUMP ASY - P/N 02974303 - S/N SWB-10361 (09-04) & DOWN... 23 PUMP ASY - P/N 02974303A - S/N SWB-10362 (10-04) & UP... 24 SERRATED KNIFE BAR ASY - 5 FT - P/N 02974361... 5 SERRATED KNIFE BAR ASY - 6 FT - P/N 02974373... 7 SERRATED SICKLE BAR ASY - 5 FT - P/N 02974360... 4 SERRATED SICKLE BAR ASY - 6 FT - P/N 02974372... 6 SHOE & BREAK-A-WAY ASY - P/N 02975194... 17 SHOE & BREAK-A-WAY PRE-ASY - P/N 02975986... 19 VALVE SOLENOID ASY - P/N 02974305... 20 2006 Alamo Group Inc. Parts Section 3
SERRATED SICKLE BAR ASY - 5 FT - P/N 02974360 02974360 -- SICKLE BAR ASY, 5 FT 1 00001200 1 NUT, HEX 1/2"-NC PL 2 00019600 1 LOCKWASHER, 1/2" HEAVY 3 00022200 2 LOCKWASHER, 7/16" STD PL 4 000516 1 CARRIAGE BOLT, 1/2"-NC X 1-3/4" 5 0012700 1 KNIFE CLIP, HIGH 6 0046400 10 PLOW BOLT, #3-7/16"-NC X 1-1/2" PL GR5 7 00999316 22 NUT, HEX 7/16"-NC PL 8 0123800 1 OUTER SHOE SOLE 9 0129000 1 CARRIAGE BOLT, 7/16"-NC X 1-3/4" PL GR5 10 0188700 4 KNIFE CLIP, LOW 11 02974345 1 CUTTER BAR, 5 FT 12 0532600 4 PLATE 13 0570900 1 OUTER SHOE ASY 14 0571800 10 PLOW BOLT #3-7/16"-NC X 2" PL GR5 15 0571900 1 WEAR PLATE 16 0593600 1 OUTER ROCK GUARD 17 0593700 18 CENTER ROCK GUARD 18 0593800 1 INNER ROCK GUARD, RH 19 12666000 1 CARRIAGE BOLT, 7/16"-NC X 1-1/2" PL GR5 2006 Alamo Group Inc. Parts Section 4
SERRATED KNIFE BAR ASY - 5 FT - P/N 02974361 02974361 -- CUTTER BAR ASY 5 FT, W/SERRATED KN 1 0064600 21 KNIFE SECTION, 3" 2 0189900 1 KNIFE PROTECTOR, CARDBOARD 63" LONG 3 02974316 1 INSERT, NYLON DRIVE BRG CLAMP 4 02974349 1 KNIFE HEAD WELDMENT 00756328 1 BOLT, HEX HEAD 10M-P1.5 X 45MM 5 02976270 35 SECTION BOLT, 5/8" LONG 6 02976271 7 HEAD BOLT, 1-1/64" LONG 7 02976272 42 SECTION LOCKNUT, (CONE) 8 0530100M 1 BACKING STRIP, 5 FT 2006 Alamo Group Inc. Parts Section 5
SERRATED SICKLE BAR ASY - 6 FT - P/N 02974372 02974372 -- SICKLE BAR ASY, 6 FT W/ SERRATED KNIVES 1 00001200 1 NUT, HEX 1/2"-NC PL 2 00019600 1 LOCKWASHER, 1/2" HEAVY 3 00022200 2 LOCKWASHER, 7/16" STD PL 4 000516 1 CARRIAGE BOLT, 1/2"-NC X 1-3/4" 5 0012700 1 KNIFE CLIP, HIGH 6 0046400 12 PLOW BOLT, #3-7/16"-NC X 1-1/2" PL GR5 7 00999316 26 NUT, HEX 7/16"-NC PL 8 0123800 1 OUTER SHOE SOLE 9 0129000 1 CARRIAGE BOLT, 7/16"-NC X 1-3/4" PL GR5 10 0188700 5 KNIFE CLIP, LOW 11 02974345 1 CUTTER BAR, 5 FT 12 0532600 5 PLATE 13 0570900 1 OUTER SHOE ASY 14 0571800 12 PLOW BOLT, #3-7/16"-NC X 2" PL GR5 15 0571900 1 WEAR PLATE 16 0593600 1 OUTER ROCK GUARD 17 0593700 22 CENTER ROCK GUARD 18 0593800 1 INNER ROCK GUARD, RH 19 12666000 1 CARRIAGE BOLT, 7/16"-NC X 1-1/2" PL GR5 2006 Alamo Group Inc. Parts Section 6
SERRATED KNIFE BAR ASY - 6 FT - P/N 02974373 02974373 -- CUTTER BAR ASY 6FT, W/SERRATED KN 1 0064600 25 KNIFE SECTION, 6 FT 2 0189900 1 KNIFE PROTECTOR, CARDBOARD 63"LONG 3 02974316 1 INSERT, NYLON DRIVE BRG CLAMP 4 02974349 1 WELDMENT KNIFE HEAD 00756328 1 BOLT, HEX HEAD 10M-P1.5 X 45MM 5 02976270 43 SECTION BOLT, 5/8" LONG 6 02976271 7 HEAD BOLT, 1-1/64" LONG 7 02976272 50 SECTION LOCKNUT (CONE) 8 0531900 1 BACKING STRIP 6 FT 2006 Alamo Group Inc. Parts Section 7
CARRIAGE ARM ASY - P/N 02974362 02974362 -- CARRIAGE ARM ASY 1 000206 2 RED LUBRICAP 2 00752670 2 GREASE FITTING, 1/4"-28 BOLT THD 3 00755153 4 COTTER PIN, 3/16" X 1-1/2" PLATED 4 0112700 2 CARRIAGE PIN 5 0113400 2 ROLL PIN, 3/8" X 2-1/2" 6 02045200 3 ADAPTER, HYD ELBOW 7 02965475 1 HOSE, #4-4FJX - 4FJX - 18"LG 8 02970702 1 ADAPTER, HYD TEE SWIVEL 9 02974324 1 CARRIAGE ARM WELDMENT 10 02974329 1 PIVOT MOUNT WELDMENT 11 0424200 4 CYLINDER LUG PIN 12 0693400A 1 CURB STOP CYLINDER 13 0693500A 1 BAR LIFT CYLINDER 2006 Alamo Group Inc. Parts Section 8
COMMON COMPONENT BOX - 02974368 02974368 -- COMMON COMPONENT BOX, SINGLE RH WING 1 00725746 1 DECAL, PELIGRO 2 02964028 1 SWITCH, PUSH PULL W/KNOB 3 02964063 1 KNOB, F/ PUSH PULL SWITCH 4 02965093 1 DECAL, PROPER ENGINE OPERATING 5 02970354 1 DECAL, KNIFE CLEARANCE 6 02974310 1 FILTER ELEMENT, 10-MICRON 7 02974318 1 WIRE HARNESS, F/SINGLE RH WING 8 02974321 1 DECAL, INSTRUCT VALVE & SWITCH 9 02974322 1 SWITCH, TOGGLE (3-POSITION) 10 02974348 1 TANK ASY, HYD 11 02974364 1 VALVE ASY, 2-SPOOL W/FTGS 12 02974962 1 BOOT, TOGGLE SWITCH COVER 13 02975270 1 DECAL, INST REVERSING SWITCH 14 0410300 1 DECAL, WARNING SIGN 2006 Alamo Group Inc. Parts Section 9
CONTROL VALVE ASY - P/N 02974364 2006 Alamo Group Inc. Parts Section 10
CONTROL VALVE ASY - P/N 02974364 02974364 -- VALVE ASY, 2-SPOOL W/FITTINGS 02974306 -- VALVE ASY, 2-SPOOL W/O FITTINGS 1 02976934 2 UNLOAD, PLUNGER 2 02966645 2 POPPET ASY 3 02966645 1 POPPET ASY 4 02976933 2 SPOOL 5 02966648 4 SEAT ASY 6 02966649 2 PLUG ASY, HEX W/5/16"-NF THDS 7 02966650 2 PORT ADAPTER PLUG ASY 8 02966651 2 BUSHING 9 02966652 2 LOCKOUT SPRING 10 02966653 1 CAP ASY 11 02966654 1 PLUG ASY 12 02976932 1 BODY 13 02976931 1 POPPET 14 02976930 1 SEAT 15 02966657 4 O-RING 16 02966658 2 RETAINING RING 17 02966659 A/R WASHER 18 02966660 A/R WASHER 19 02966661 A/R WASHER 20 02966662 1 WASHER 21 02976946 1 CAP, ASY 22 02976945 1 SPRING 23 02966669 1 SPRING 24 02976944 2 PLUG ASSY 25 02976943 1 WASHER 26 02976942 1 WASHER 27 02976941 3 BALL 28 02976940 1 SPRING 29 02976939 1 SPRING 30 02976938 1 CONE 31 02976937 1 SPACER 32 02976936 1 ADAPTOR CAP 33 02976935 A/R WASHER 34 02966671 2 WIPER SEAL 35 02976957 2 HANDLE KIT 2006 Alamo Group Inc. Parts Section 11
FILTER ASY - P/N 02974309 02974309 -- FILTER ASY. W/ AIR BREATHER ELEMENT 1 02976906 1 BOWL 2 02976907 1 FILTER GUAGE 3 02976908 1 SPRING 4 02974319 1 AIR BREATHER ELEMENT 5 02976909 1 AIR BREATHER KIT 6 02974310 1 FILTER ELEMENT 7 02976910 1 SEAL KIT 8 02979341 1 COVER 2006 Alamo Group Inc. Parts Section 12
HYDRAULIC TANK ASY - P/N 02974348 2006 Alamo Group Inc. Parts Section 13
HYDRAULIC TANK ASY - P/N 02974348 02974348 -- TANK ASY, HYD 1 00017000 8 LOCKWASHER, 1/4" PL STD 2 001891 1 ADAPTER, HYD ELBOW 4MP - 6MJ 3 00696800 3 ADAPTER, HYD STRAIGHT 4 10121000 2 BOLT, HEX HEAD 5/16"-NC X 1-1/4" PL GR5 5 0117100 1 DRAIN PLUG, MAGNETIC 6 02959924 2 LOCKNUT, TOPLOCK 1/4"-NC PLB 7 02962213 1 ADAPTER, HYD ELBOW 10 02968880 1 GAUGE, SIGHT/TEMPERATURE 11 02974305 1 VALVE, SOLENOID CONTROL 12 02974309 1 FILTER ASY W/INT FILLR/BREATHR 13 02974312 1 SUCTION STRAINER, 100 MESH 14 02974320 1 HOSE, #8-8FJX - 8FJX - 14"LG 15 02974366 1 HYDRAULIC TANK WELDMENT 16 02974369 1 TANK ACCESS COVER 17 02974370 1 ADAPTER, HYD ELBOW 12MB - 8MJ 90DEG 18 064600D 1 COVER GASKET 19 10058000 8 BOLT, HEX HEAD 1/4"-NC X 1" PL GR5 20 10074000 2 BOLT, HEX HEAD 1/4"-NC X 3" PL GR5 22 000752 1 ELBOW, STREET 1/8"-90 DEG 23 02976123 2 WASHER, SEALING 1/4" 24 00011700 2 LOCKWASHER, 5/16" PL STD 25 02976124 8 INSERT, KNURLED & THREADED 26 02976125 2 INSERT, KNURLED & THREADED 2006 Alamo Group Inc. Parts Section 14
KNIFE DRIVE ASY - P/N 02974300 02974300 -- HORIZONTAL KNIFE DRIVE ASY 1 02974311 1 FLYWHEEL, HORIZONTAL KNIFE DRIVE 2 02974315 1 ADAPTER, HUB 3 02974317 1 STUD, KNIFE DRIVE BEARING 4 02977820 2 BOLT, SOCKET HEAD 10M-P1.50 X 35MM PL GR8.8 (TORQUE TO 35 FT. LBS.) 2006 Alamo Group Inc. Parts Section 15
MOTOR ASY - P/N 02974301 02974301 -- MOTOR ASY, GEROTOR 2.8 CID 1" SHAFT 1 02976883 1 SHAFT, GEROTOR INTERNAL DRIVE 2 02976884 1 SET, GEROTOR STAR & HOUSING 3 02976885 7 SCREW, GEROTOR HOUSING TIE 4 02976886 4 SCREW, FLANGE 5 02976887 1 FLANGE, MOTOR SAE 2-BOLT A 6 02976888 1 RACE, THRUST BEARING 7 02976889 1 BEARING, THRUST 8 02976890 1 SHAFT, OUTPUT 1" STRAIGHT 9 02976891 1 HOUSING, GEROTOR MOTOR 10 02976892 1 PLUG 11 02976893 1 PLATE, SPACER 12 02976894 1 CAP, END 13 MA000229 1 KEY 5/16" SQ. X 1" LG 14 02976895 1 SEAL KIT, GEROTOR MOTOR (ALL ITEMS MARKED ITEM 14) 2006 Alamo Group Inc. Parts Section 16
SHOE & BREAK-A-WAY ASY - P/N 02975194 2006 Alamo Group Inc. Parts Section 17
SHOE & BREAK-A-WAY ASY - P/N 02975194 02975194 -- SHOE & BREAK-A-WAY ASY 1 00000200 5 NUT, HEX 3/4"-NC PL 2 00001200 1 NUT, HEX 1/2"-NC PL 3 00001800 10 LOCKNUT, TOPLOCK 1/2"-NC PLB 5 00002701 2 FLATWASHER, 3/4" TYPE AW ZP 6 00011100 2 FLATWASHER, 3/8" PL STD 7 00015800 2 LOCKNUT, TOPLOCK 3/8"-NC PLB 8 5C8130 1 NUT, HEX JAM 1/2" ZP 9 000206 3 RED LUBRICAP 11 02974343 2 TUBE, 1-1/4" OD X 9/16" ID X 3-3/4" LONG 12 00749130 2 BOLT, HEX HEAD 1/2"-13NC X 1-3/4" PL GR5 13 02974344 1 SOLE SKID SHOE 14 00752670 1 GREASE FITTING, 1/4-28 BOLT THD 15 00753642 2 BOLT, HEX HEAD 3/8"-NC X 1-1/4" ZP GR5 16 02974354 1 SPACER, CUTTER BAR 17 02974358 1 ROD, DEFLECTOR 18 02042300 2 ADAPTER, HYD STRAIGHT 19 02931300 3 BOLT, HEX HEAD 3/4"-NC X 2" ZP GR5 20 02972570 3 LOCKWASHER, 3/4" PL STD 21 02974300 1 HORIZONTAL KNIFE DRIVE ASY 22 02974301 1 MOTOR GEROTOR, 2.8 CID 1" SHAFT 23 02976853 4 PLOW BOLT, #3-1/2"-NC X 2-1/2" PL GR8 24 02976854 4 PLOW BOLT, #3-1/2"-NC X 7" PL GR8 25 02974313 1 BRACKET, HYD MOTOR ADAPTER 26 02974342 2 TUBE, 1-1/4" OD X 9/16" ID X 4-5/8" LONG 27 02975986 1 SHOE & BREAKAWAY PRE-ASY 2006 Alamo Group Inc. Parts Section 18
SHOE & BREAK-A-WAY PRE-ASY - P/N 02975986 02975986 -- SKIDSHOE & BREAK-A-WAY PRE-ASY 1 00011100 1 FLATWASHER, 3/8" PL STD 2 03101646 1 LOCKWASHER, 3/8 MEDIUM ZP 3 00002000 1 BOLT, HEX HEAD 3/8"-16 X 3/4" GR GR5 ZP 5 03200250 1 RUBBER BUMPER PAD 6 02974363 6 WASHER, 17/32" ID X 2" OD X.1345" 7 00019600 1 LOCKWASHER, 1/2" HEAVY 8 00019300 1 BOLT, HEX HEAD 1/2"-NF X 1-1/2" PL GR5 NOTE: Items 4, 9, 10, 11 & 12 can only be shipped as a preloaded assembly and are not available as replacement components. DO NOT attempt to remove any parts of this pre-assembly that are spring loaded. 2006 Alamo Group Inc. Parts Section 19
VALVE SOLENOID ASY - P/N 02974305 02974305 -- VALVE, SOLENOID CONTROL 1 02979345 1 BODY, SICKLE MOWER 2 02979346 1 CARTRIDGE, RELIEF 3 02979190 1 BOLT KIT 4 02979349 1 SOLENOID, SELECTOR VALVE 5 02979186 1 ASY, STEM TUBE 6 02979187 1 COIL 7 02979188 1 COIL NUT 2006 Alamo Group Inc. Parts Section 20
PUMP ASY - P/N 02974302 - S/N SWB-10361 (09-04) & DOWN 02974302 -- PUMP ASY, 1.16/0.49 CID/REV (STEEL MOUNTING FLANGE & END CAP) 1 02976923 1 CONNECTING SHAFT 2 02976922 1 GEAR SET 3 02976921 1 GEAR SET 4 02976920 1 END CAP (STEEL END CAP) 5 02976919 1 MOUNTING FLANGE (STEEL MOUNTING FLANGE) 6 02976918 1 GEAR HOUSING 7 02976917 1 GEAR HOUSING 8 02976916 4 HOUSING TIE BOLT 9 02976915 2 DOWEL PIN 10 02976914 2 DOWEL PIN 11 02976913 1 MID SPACER PLATE 12 02976912 4 THRUST BLOCK 13 02976911 4 WASHER * 02976924 REF SEAL KIT ( INCLUDES ITEMS W / * ) 2006 Alamo Group Inc. Parts Section 21
PUMP ASY - P/N 02974302A - S/N SWB-10362 (10-04) & UP 02974302A -- PUMP ASY, 1.16/0.49 CID/REV (ALUMINUM MOUNTING FLANGE & END CAP) 1 02980846 1 MOUNTING FLANGE, (ALUMINUM MOUNTING FLANGE) 2 02980847 1 END CAP, (ALUMINUM END CAP) 3 02980848 1 HOUSING, (F/ LARGE GEAR SECTION) 4 02976913 1 MID SECTION SPACER PLATE 5 02980849 1 HOUSING, (F/ SMALL GEAR SECTION) 6 -------------- 4 SEAL, BACK UP (INCLUDED N SEAL KIT) 7 02980850 1 DRIVE GEAR, (LARGE GEAR) 8 02980851 1 DRIVEN GEAR, (LARGE GEAR) 9 02980852 1 DRIVE GEAR, (SMALL GEAR) 10 02980853 1 DRIVEN GEAR, (SMALL GEAR) 11 -------------- 1 SHAFT SEAL, (INCLUDED IN SEAL KIT) 12 02980856 1 SNAP RING 13 02980857 4 THRUST BLOCK, (F/ LARGE OR SMALL GEAR SECTION) 14 ------------- 4 CHANNEL SEAL, (INCLUDED IN SEAL KIT) 15 02976911 4 WASHER 16 02980854 4 FASTENER, (173MM) 17 02980855 4 NUT 18 -------------- 4 SECTIONAL SEAL, (INCLUDED IN SEAL KIT) 19 02976915 2 PIN, DOWEL, (SHORT PIN) 20 02976914 2 PIN, DOWEL, (LONG PIN) 21 02976923 1 CONNECTING, SHAFT 22 02980858 1 SEAL KIT, (F/ LARGE GEAR SECTION) 23 02980859 1 SEAL KIT, (F/ SMALL GEAR SECTION) 2006 Alamo Group Inc. Parts Section 22
PUMP ASY - P/N 02974303 - S/N SWB-10361 (09-04) & DOWN 02974303 -- PUMP ASY, 0.98/0.37 CID/REV (STEEL END CAP & MOUNTING FLANGE) 1 02976923 1 CONNECTING SHAFT 2 02976929 1 GEAR SET, (SMALL GEARS) 3 02976928 1 GEAR SET, (LARGE GEARS) 4 02976920 1 END CAP (STEEL END CAP) 5 02976919 1 MOUNTING FLANGE (STEEL MOUNTING FLANGE) 6 02976927 1 GEAR HOUSING (F/ SMALL GEAR END) 7 02972926 1 GEAR HOUSING (F/ LARGE GEAR END) 8 02976925 4 HOUSING TIE BOLT 9 02976915 2 DOWEL PIN, (F/ MOUNTING FLANGE) 10 02976914 2 DOWEL PIN, (F/ GEAR HOUSINGS) 11 02976913 1 MID SPACER PLATE 12 02976912 4 THRUST BLOCK (F/ SMALL OR LARGE GEAR SECTION) 13 02976911 4 WASHER (F/ HOUSING TIE BOLTS) 14 02976924 REF SEAL KIT NOTE: Seal Kit Item 18 includes input seal (1), backup seals (2), channel seals (2) and section seal o-rings (2)or first pump section. NOTE: Seal Kit Item 19 includes backup seals (2), channel seals (2) and section seal o-rings (2)or second pump section. 2006 Alamo Group Inc. Parts Section 23
PUMP ASY - P/N 02974303A - S/N SWB-10362 (10-04) & UP 02974303A -- PUMP ASY, 0.98/0.37 CID/REV (ALUMINUM MOUNTING FLANGE & END CAP) 1 02976911 4 WASHER 2 02976913 1 MID SPACER PLATE 3 02976914 2 PIN, DOWEL 4 02976915 2 PIN, DOWEL 5 02976923 1 CONNECTING, SHAFT 6 02980846 1 MOUNTING FLANGE (ALUMINUM MOUNTING FLANGE) 7 02980847 1 END CAP ( ALUMINUM END CAP ) 8 02980860 1 GEAR HOUSING, ( F/ LARGE GEAR SET ) 9 02980861 1 GEAR HOUSING, ( F/ SMALL GEAR SET ) 10 02980862 1 DRIVE GEAR & INPUT SHAFT ( F/ LARGE GEAR ) 11 02980863 1 DRIVEN GEAR ( F/ LARGE GEAR ) 12 02980864 1 DRIVE GEAR ( F/ SMALL GEAR ) 13 02980865 1 DRIVEN GEAR ( F/ SMALL GEAR ) 14 02980866 4 HOUSING TIE BOLT - 150 MM 15 02980856 1 SNAP RING 16 02980857 4 THRUST BLOCK, (F/ LARGE OR SMALL GEAR SECTION) 17 -------------- 1 INPUT SEAL, (INCLUDED IN SEAL KIT) 18 02980858 1 SEAL KIT, (F/ LARGE GEAR SECTION) 19 02980859 1 SEAL KIT, (F/ SMALL GEAR SECTION) NOTE: Seal Kit Item 18 includes input seal (1), backup seals (2), channel seals (2) and section seal o-rings (2)or first pump section. NOTE: Seal Kit Item 19 includes backup seals (2), channel seals (2) and section seal o-rings (2)or second pump section. 2006 Alamo Group Inc. Parts Section 24
CYLINDER ASY - BAR TILT - P/N 0693500A 0693500A -- BAR LIFT CYLINDER ASY. 1 02977114 1 TUBE WLD MT 2 02977116 1 CYL HEAD 3 02977115 1 ROD WLD MT 4 --------------- 1 * O-RING 5 --------------- 1 * BACK-UP SEAL RING 6 --------------- 1 * ROD SEAL 7 --------------- 1 * ROD WIPER 8 --------------- 1 * WIRE RING 9 02977121 1 SEAL KIT, ( * INCLUDES ITEMS 4, 5, 6, 7 & 8 ) 2006 Alamo Group Inc. Parts Section 25
CYLINDER ASY - CURB LIFT - P/N 0693400A 0693400A -- CURB STOP CYLINDER ASY. 1 02977114 1 TUBE WLD MT 2 02977116 1 CYLINDER HEAD 3 02977118 1 PISTON 4 02977122 1 ROD WLDMT 5 02977123 1 CYLINDER ROD 6 02208000 1 LOCKNUT 7 --------------- 1 * PSP SEAL 8 --------------- 1 * O-RING 9 --------------- 1 * BACK-UP RING 10 --------------- 1 * ROD SEAL 11 --------------- 1 * NYLON WEAR RING 12 --------------- 1 * SNAP IN ROD SEAL 13 --------------- 1 * WIRE RING 14 02977121 1 SEAL KIT, ( * INCLUDES ITEMS 7, 8, 9, 10, 11, 12 & 13 ) 2006 Alamo Group Inc. Parts Section 26
DECALS - FRAME AND TANK SWITCHBLADE 5 & 6 MECH BRK-A-WAY (06-04) 2006 Alamo Group Inc. Parts Section 27
DECALS - FRAME AND TANK ITEM PART NO. QTY. TYPE DESCRIPTION 1 02966305 1 INSTRUCTION DECAL, UNIVERSAL TRACTOR 2 02974997 1 NAME DECAL, NAME SWITCH BLADE SICKLE 3 02965262 1 WARNING DECAL, WARNING HOSE BURST 6 02962765 1 DANGER DECAL, MULTIPLE HAZARD 7 0614500 1 CAUTION DECAL, CAUTION 8 ----REF---- 1 S/N PLATE SERIAL NUMBER PLATE 9 00776481 1 INSTRUCTION SHEET, MANUAL CANISTER DECAL 10 00776031 1 PARTS CANISTER, PARTS MANUAL 11 02974374C 1 PARTS MANUAL OPERATORS SWITCH BLADE 12 10058000 3 BOLT 13 00017000 3 LOCKWASHER 14 00024100 3 FLATWASHER 15 02959924 3 LOCKNUT 16 000678 1 INSTRUCTION DECAL, GREASE FITTING INSIDE 02981984 1 PARTS MOTOR / DRIVE ASY. COVER 17 02968880 1 PARTS GAUGE, SIGHT / TEMPERATURE SWITCHBLADE 5 & 6 MECH BRK-A-WAY (06-04) 2006 Alamo Group Inc. Parts Section 28
DECALS - CAB & ROPS ITEM PART NO. QTY. TYPE DESCRIPTION 1 02970354 1 INSTRUCTION DECAL, KNIFE CLEARANCE 2 02965093 1 INSTRUCTION DECAL, PROPER ENGINE OPERATING 3 00725746 1 PELIGRO DECAL, PELIGRO 4 0410300 1 WARNING DECAL, WARNING SIGN 5 02975270 1 INSTRUCTION DECAL, REVERSING SWITCH 6 02974321 1 INSTRUCTION DECAL, VALVE & SWITCH 7 02982584 1 INSTRUCTION DECAL, CUTTER BREAK-A-WAY RESET INSTRUCTIONS 8 02964028 1 SWITCH,PUSH PULL (W/ KNOB & HARDWARE) 9 02982367 1 KNOB (HARDWARE F/ 02964028) 02982365 1 FACE NUT (HARDWARE F/ 02964028) 02982366 1 JAM NUT (HARDWARE F/ 02964028) SWITCHBLADE 5 & 6 MECH BRK-A-WAY (06-04) 2006 Alamo Group Inc. Parts Section 29
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
Switch Blade 5 ft. & 6 ft MECH BRK-A-WAY (06/04) 2006 Alamo Group Inc. Printed U.S.A. Manual P/N 02974374P