I.C. ENGINE POWERED FORKLIFT TRUCK

I.C. ENGINE POWERED FORKLIFT TRUCK Counter-Balance Type 1,5-3,5 ton Havelange lifts, driven by service FG15C13 / FG15T13 / FHG15C3 / FHG15T3 FD15C13 / FD15T13 / FHD15C3 / FHD15T3 / FHD15C3Z / FHD15T3Z FG18C13 / FG18T13 / FHG18C3 / FHG18T3 FD18C13 / FD18T13 / FHD18C3 / FHD18T3 / FHD18C3Z / FHD18T3Z FG20C3 / FG20T3 / FHG20C3 / FHG20T3 FD20C3 / FD20T3 / FD20C3Z / FD20T3Z / FHD20C3 / FHD20T3 FG25C3 / FG25T3 / FHG25C3 / FHG25T3 FD25C3 / FD25T3 / FD25C3Z / FD25T3Z / FHD25C3 / FHD25T3 FG30C3 / FG30T3 / FHG30C3 / FHG30T3 FD30C3 / FD30T3 / FD30C3Z / FD30T3Z / FHD30C3 / FHD30T3 FD35T3S www.havelangeforklifts.be

GENERAL ENHANCED OPERATOR COMFORT SUBSTANTIALLY REDUCED VIBRATION BY ADOPTING DUAL-FLOATING SYSTEMS FOR BOTH THE ENGINE AND HOOD Minimizes the transfer of vibration to the operator, with fourpoint rubber cushion absorbers between the seat and engine and its transmission. Moreover, use of the same four-point suspension adopted in the hood, realizing a dual effect in reducing vehicle vibrations. EXPANSIVE FLOOR SPACE FOR EASIER FOOT MANEUVERING An amazing 45% increase in floor space by placing tilt cylinders under the floor. This gives a smooth footwell in addition to easy entry and exit. MORE CONVENIENT PARKING LEVER The lever is positioned to the right of the steering wheel for easier entry and exit. A double-action brake release on the lever further improves safety. EXTRA ENTRY AND EXIT FROM AN EXTRA-WIDE STEP -- 55% WIDER The secure step with enlarged foot space enables greater comfort and less fatigue while entering and exiting the vehicle. MULTIFUNCTIONAL SUSPENSION SEAT (available for 1.5/1.8 ton high power & 2/3.5 ton models) Features include reinforced driver support, reduced vibration, operator weight balance adjusting, forward and backward reclining, a rear utility pocket and seat belt. RESIN SCREEN The resin screen on the overhead guard enables comfortable outdoor operation in wet weather.

SUPERIOR MANEUVERABILITY AND ASSURED SAFETY INNOVATIVE FORK-LANDING MECHANISM (available for wide view two-stage mast) The fork-lowering speed decelerates at a height of approximately 150 mm above the ground enabling accurate placement of the forks into the load fork pockets or pallet. REDUCED FATIGUE DUE TO A SEMI-CIRCULAR STEERING WHEEL A smaller diameter (300 mm outer diameter) steering wheel gives improved vehicle maneuverability. In addition, this compact steering wheel makes it much easier to get on and off the truck. METER PANEL OPTIMALLY LOCATED TO THE RIGHT OF THE DRIVER S SEAT The meter panel is located on the top right side of the dashboard for easier readability by the operator. MULTI-CONE SYNCHRONIZER SHIFT LEVERS The newly adopted levers enable smooth shifting from both forward and reverse (available for manual transmission models). ANTI-ROLL MECHANISM FOR ASSURED SAFETY DURING TURNING (available for 2-3.5 ton models) Warning: This system does not guarantee accident avoidance or prevention of vehicle overturning. NEUTRAL SAFETY MECHANISM This feature enhances safety of operation. The engine cannot be started unless the change lever is in the neutral position. ANTI-SLIP MAT ON THE HOOD A rubber strip is attached to the hood to prevent slippage while stepping on and off. METER PANEL WITH LCD INDICATORS The LCD has a longer life and is easy to read even during daylight shift operation. HIGH-MOUNT REAR COMBINATION LIGHTS The rear combination lights are installed on the top left and right sides of the overhead guard for easier recognition by on-site workers. EXCELLENT OPERATOR VISIBILITY Wider forward visibility Clearer visibility of the fork tips -- 50% improvement over other current models. This achievement was made possible by lowering the dashboard by 70mm and the tie bar by 190mm. A remarkable improvement of the forward view along with quicker recognition of the fork position. An operatorfriendly design with assured safety, high efficiency and relaxing feel. Amazing backward visibility Reshaped counter weight for better rearview sight. The round shape of the rear top end of the counterweight substantially improves visibility for increased safety during backward movement.

RUGGEDNESS AND INCREASED DURABILITY SINGLE-PIECE HEADGUARD The front and rear pillars as well as roof are all welded together in a single-piece construction to give additional strenght to the entire structure. TCM TRANSMISSIONS TCM designed and developped these transmissions for quiet operation and maximum durability, and TCM builds them to insure the highest quality. TCM STEERING AXLES Also a new TCM design, the steer axle has been strengthened and improved for durability in demanding applications. STURDIER MAST Minimized distortion of the mast by redesigned positioning the mast supports and tilt cylinders. TCM s traditional robust mast was further upgraded by adopting sturdier tie bars, while maintaining a wide range of viewing angles. IMPROVED DURABILITY WITH LUBRICANT FILLED LIFT CYLINDER Oil filled lift cylinders give improved durability. (available for 2-3.5 ton models) COOLER RUNNING THROUGH IMPROVED AIRFLOW Optimal positioning of the fan, radiator and muffler has reduced the operating coolant temperature (gasoline models). The operating temperature of the hydraulic oil has been reduced, also by 10 C by upgrading the mechanical components and circuitry. 5% IMPROVED FRONT AND REAR STABILITY RATIO (available for 2-3.5 ton models) Stable and more consistent cargo handling as well as travel due to an improved stability ratio.

EASY MAINTENANCE AND ENVIRONMENT FRIENDLINESS DETACHABLE SIDE COVERS FOR CONVENIENT INSPECTION AND SIMPLE MAINTENANCE Inspection and maintenance can more easily be performed due to one-touch detachable side covers and a wide-opening hood. INTEGRAL LAYOUT OF ELECTRICAL PARTS AND OTHER SYSTEM DEVICES Maintenance inspections can be performed more easily, as electrical parts such as the fuse box, relay and battery are neatly integrated into a conveniently compact area. NEW ENGINES, COMPLIANT WITH WORLDWIDE 2 nd STAGE EMISSION REGULATIONS Powerful, yet appropriate, diesel engines, compliant with stringent global emissions regulations. ONE-PIECE FLOORBOARD Gives more convenient inspection and easier maintenance, as the one-piece floorboard unit is easily detachable without using any tools. NEW OPTIONAL EQUIPMENT Three-stage mast with fourcylinder mechanism (available for 2-3 ton models) The cylinders are symmetrically located to the left and right for improved forward visibility. PORTABLE GLOVE BOX Detachable and portable. Integral Side Shifter A major improvement in the integral side shifter ensures less load loss and improved forward visibility. Low-noise mast (available for 2-3 ton models) Reduced noise from the fork and carriage significantly reduces chain shudder. CUP HOLDER Convenient for keeping cups, pens and other small items. Lift Lock With the engine is off, the forks cannot be lowered, even when the operator is in the seat. Interlock System This safety device allows traveling and loading/unloading only when the operator is in the seat.

OTHER OPTIONAL EQUIPMENT Rotating warning light Rear working light Overhead exhaust system Windshield wiper Cabin-panel type (available for 2-3.5 ton models) Heater LPG exclusive/dual fuel (LPG/gasoline) package Pre-cleaner engine air intake Steel cabin-enclosed type with air-cooler (available for 2-3.5 ton models) * As far as the detailed optional information is concerned, please refer to the specification sheets. For various types of attachments, please also refer to the attachment catalogue which is separately prepared from this sales catalogue. Head light guard Air Boss tire

TCM has been engaged in manufacturing various forklift truck models that take into account the needs and requirements of our valued cutomers. Now, TCM proudly presents the inoma series with such benefits as enhanced operator comfort, superior safety assurance, ruggedness and increased durability as well as easy maintenance and envirnment friendliness. These notable benefits are backed by TCM s many years of experience and superb technological innovations, and TCM is confident in placing the full inoma series product line on variaus job sites in markets around the world. 1,5 ton FG15C13 FD15C13 FHD15C3 FG15T13 FD15T13 FHD15T3 FHG15C3 FHD15C3Z FHG15T3 FHD15T3Z 1,8 ton FG18C13 FD18C13 FHD18C3 FG18T13 FD18T13 FHD18T3 FHG18C3 FHD18C3Z FHG18T3 FHD18T3Z 2,0 ton FG20C3 FD20C3 FHD20C3 FG20T3 FD20T3 FHD20T3 FHG20C3 FD20C3Z FHG20T3 FD20T3Z 2,5 ton FG25C3 FD25C3 FHD25C3 FG25T3 FD25T3 FHD25T3 FHG25C3 FD25C3Z FHG25T3 FD25T3Z 3,0 ton FG30C3 FD30C3 FHD30C3 FG30T3 FD30T3 FHD30T3 FHG30C3 FD30C3Z FHG30T3 FD30T3Z 3,5 ton FD35T3S

SPECIFICATIONS -- 1,5-1,8 ton Wide view VM FG / D15T13 FG / D15C13 FG / D18T13 FG / D18C13 Overall Lowered Raised with F / B FG15T3 FG15C3 Service Weight (kg) FG18T3 FG18C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD VM250 1500 1500 1750 1750 2500 1745 3530 6 / 10 2475 2505 2585 2635 2650 2730 VM270 1500 1500 1750 1750 2700 1845 3730 6 / 10 2490 2520 2600 2650 2665 2745 VM300 1500 1500 1750 1750 3000 1995 4030 6 / 12 2510 2540 2620 2670 2685 2765 VM330 1500 1500 1750 1750 3300 2145 4330 6 / 12 2525 2555 2635 2685 2700 2780 VM350 1500 1500 1750 1750 3500 2245 4530 6 / 12 2540 2570 2650 2700 2715 2795 VM375 1500 1500 1750 1750 3750 2370 4780 VM400 1500 1500 VM425 1400 1400 VM450 1400 1400 VM475 VM500 1650 *1750 1500 *1750 1500 *1650 1650 *1750 1500 *1750 1500 *1650 4000 2545 5030 4250 2670 5280 4500 2795 5530 4750 2920 5780 5000 3045 6030 * * 2555 2585 2665 2715 2730 2810 2595 2625 2705 2755 2770 2850 2615 2645 2725 2775 2790 2870 2625 2655 2735 2785 2800 2880 2540 2670 2750 2800 2815 2895 2660 2690 2770 2820 2835 2915 VM550 *1100 *1100 *1300 *1300 5500 3345 6530 *3 / 6 2715 2745 2825 2875 2890 2970 VM600 *800 *800 * * 6000 3595 7030 *3 / 6 2745 2775 2855 2905 2920 3000 Weight for diesel model: +30kg FHG15T13 / FHD15T3Z FHG15C13 / FHD15C3Z FHG18T13 / FHD18T3Z FHG18C13 / FHD18C3Z Overall Lowered Raised with F / B FHG15T3 FHG15C3 Service Weight (kg) FHG18T3 FHG18C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD VM250 1500 1500 1750 1750 2500 1745 3530 6 / 10 2475 2505 2585 2635 2650 2730 VM270 1500 1500 1750 1750 2700 1845 3730 6 / 10 2490 2520 2600 2650 2665 2745 VM300 1500 1500 1750 1750 3000 1995 4030 6 / 12 2510 2540 2620 2670 2685 2765 VM330 1500 1500 1750 1750 3300 2145 4330 6 / 12 2525 2555 2635 2685 2700 2780 VM350 1500 1500 1750 1750 3500 2245 4530 6 / 12 2540 2570 2650 2700 2715 2795 VM375 1500 1500 1750 1750 3750 2370 4780 VM400 1500 1500 VM425 1400 1400 VM450 1400 1400 VM475 VM500 1650 *1750 1500 *1750 1500 *1650 1650 *1750 1500 *1750 1500 *1650 4000 2545 5030 4250 2670 5280 4500 2795 5530 4750 2920 5780 5000 3045 6030 * * 2555 2585 2665 2715 2730 2810 2595 2625 2705 2755 2770 2850 2615 2645 2725 2775 2790 2870 2625 2655 2735 2785 2800 2880 2540 2670 2750 2800 2815 2895 2660 2690 2770 2820 2835 2915 VM550 *1100 *1100 *1300 *1300 5500 3345 6530 *3 / 6 2715 2745 2825 2875 2890 2970 VM600 *800 *800 * * 6000 3595 7030 *3 / 6 2745 2775 2855 2905 2920 3000 Weight for diesel model: +110kg (TD 27)

Wide view Full Free 2-stage VFM FG / D15T13 FG / D15C13 FG / D18T13 FG / D18C13 Overall Lowered (2) Raised with F / B FG15T3 FG15C3 (3) Service Weight (kg) FG18T3 FG18C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD VFM250 1500 1500 1750 1750 2500 1745 3530 6 / 10 2510 2540 2620 2670 2685 2765 VFM270 1500 1500 1750 1750 2700 1845 3730 6 / 10 2525 2555 2635 2685 2700 2780 VFM300 1500 1500 1750 1750 3000 1995 4030 6 / 12 2545 2575 2655 2705 2720 2800 VFM330 1500 1500 1750 1750 3300 2145 4330 6 / 12 2565 2595 2675 2725 2740 2820 VFM350 1500 1500 1750 1750 3500 2245 4530 6 / 12 2575 2605 2685 2735 2750 2830 VFM375 1500 1500 1750 1750 3750 2370 4780 VFM400 1500 1500 VFM425 1400 1400 VFM450 1400 1400 VFM475 VFM500 1300 1200 1650 *1750 1500 *1750 1500 *1650 1650 *1750 1500 *1750 1500 *1650 1300 1200 4000 2545 5030 4250 2670 5280 4500 2795 5530 4750 2920 5780 5000 3045 6030 * * 2590 2620 2700 2750 2765 2845 2640 2670 2750 2800 2815 2895 2660 2690 2770 2820 2835 2915 2675 2705 2785 2835 2850 2930 2690 2720 2800 2850 2865 2945 2705 2735 2815 2865 2880 2960 VFM550 *1100 *1100 *1300 *1300 5500 3345 6530 *3 / 6 2765 2795 2875 2925 2940 3020 VFM600 *800 *800 * * 6000 3595 7030 *3 / 6 2800 2830 2910 2960 2975 3055 For height without backrest: -470mm. (2) For free lift without backrest: +470mm. Weight for without backrest: -20kg. (3) Weight for diesel model: +30kg FHG15T13 / FHD15T3Z FHG15C13 / FHD15C3Z FHG18T13 / FHD18T3Z FHG18C13 / FHD18C3Z Overall Lowered (2) Raised with F / B FHG15T3 FHG15C3 (3) Service Weight (kg) FHG18T3 FHG18C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD VFM250 1500 1500 1750 1750 2500 1745 3530 6 / 10 2510 2540 2620 2670 2685 2765 VFM270 1500 1500 1750 1750 2700 1845 3730 6 / 10 2525 2555 2635 2685 2700 2780 VFM300 1500 1500 1750 1750 3000 1995 4030 6 / 12 2545 2575 2655 2705 2720 2800 VFM330 1500 1500 1750 1750 3300 2145 4330 6 / 12 2565 2595 2675 2725 2740 2820 VFM350 1500 1500 1750 1750 3500 2245 4530 6 / 12 2575 2605 2685 2735 2750 2830 VFM375 1500 1500 1750 1750 3750 2370 4780 VFM400 1500 1500 VFM425 1400 1400 VFM450 1400 1400 VFM475 VFM500 1300 1200 1650 *1750 1500 *1750 1500 *1650 1650 *1750 1500 *1750 1500 *1650 1300 1200 4000 2545 5030 4250 2670 5280 4500 2795 5530 4750 2920 5780 5000 3045 6030 * * 2590 2620 2700 2750 2765 2845 2640 2670 2750 2800 2815 2895 2660 2690 2770 2820 2835 2915 2675 2705 2785 2835 2850 2930 2690 2720 2800 2850 2865 2945 2705 2735 2815 2865 2880 2960 VFM550 *1100 *1100 *1300 *1300 5500 3345 6530 *3 / 6 2765 2795 2875 2925 2940 3020 VFM600 *800 *800 * * 6000 3595 7030 *3 / 6 2800 2830 2910 2960 2975 3055 For height without backrest: -470mm. (2) For free lift without backrest: +470mm. Weight for without backrest: -20kg. (3) Weight for diesel model: +110kg (TD27)

Wide view Full Free 3-stage VFHM FG / D15T13 FG / D15C13 FG / D18T13 FG / D18C13 Overall Lowered (2) Raised with F / B FG15T3 FG15C3 (3) Service Weight (kg) FG18T3 FG18C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD VFHM360 1400 1400 1600 1600 3600 1745 4630 2635 2665 2745 2795 2810 2890 VFHM400 1400 1400 1600 1600 4000 1870 5030 2660 2690 2770 2820 2835 2915 VFHM435 VFHM480 VFHM500 VFHM540 VFHM600 1350 *1400 1300 1100 *1300 850 *1250 550 *1100 1350 *1400 1350 1300 *1300 1100 *1250 750 *1100 1550 *1600 1400 *1550 1150 900 *1400 550 *1250 1600 *1600 1450 *1550 1350 1100 *1400 750 *1250 4350 1995 5380 4800 2145 5830 5000 2245 6030 5400 2370 9430 6000 2595 7030 * * * 3 / 6 *3 / 6 3 / 6 *3 / 6 2685 2715 2795 2845 2860 2940 2710 2740 2820 2870 2885 2965 2730 2760 2840 2890 2905 2985 2750 2780 2860 2910 2925 3005 2815 2845 2925 2975 2990 3070 VFHM650 *950 *950 *1100 *1100 6500 2810 7530 *3 / 3 2860 2890 2970 3020 3035 3115 VFHM700 *750 *750 *750 *750 7000 3030 8030 *3 / 3 2900 2930 3010 3060 3075 3155 For height without backrest: -505mm. (2) For free lift without backrest: +500mm. Weight without backrest: -20kg. (3) Weight for diesel model: +30kg FHG15T13 / FHD15T3Z FHG15C13 / FHD15C3Z FHG18T13 / FHD18T3Z FHG18C13 / FHD18C3Z Overall Lowered (2) Raised with F / B FHG15T3 FHG15C3 (3) Service Weight (kg) FHG18T3 FHG18C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD VFHM360 1400 1400 1600 1600 3600 1745 4630 2635 2665 2745 2795 2810 2890 VFHM400 1400 1400 1600 1600 4000 1870 5030 2660 2690 2770 2820 2835 2915 VFHM435 VFHM480 VFHM500 VFHM540 VFHM600 1350 *1400 1300 1100 *1300 850 *1250 550 *1100 1350 *1400 1350 1300 *1300 1100 *1250 750 *1100 1550 *1600 1400 *1550 1150 900 *1400 550 *1250 1600 *1600 1450 *1550 1350 1100 *1400 750 *1250 4350 1995 5380 4800 2145 5830 5000 2245 6030 5400 2370 9430 6000 2595 7030 * * * 3 / 6 *3 / 6 3 / 6 *3 / 6 2685 2715 2795 2845 2860 2940 2710 2740 2820 2870 2885 2965 2730 2760 2840 2890 2905 2985 2750 2780 2860 2910 2925 3005 2815 2845 2925 2975 2990 3070 VFHM650 *950 *950 *1100 *1100 6500 2810 7530 *3 / 3 2860 2890 2970 3020 3035 3115 VFHM700 *750 *750 *750 *750 7000 3030 8030 *3 / 3 2900 2930 3010 3060 3075 3155 For height without backrest: -505mm. (2) For free lift without backrest: +500mm. Weight without backrest: -20kg. (3) Weight for diesel model: +110kg (TD27) Rated Capacity with (*): Shows capacity with front dual tires. Service Weight of VM/VFM 550-600 and of VFHM 650-700 represents the weight of vehicles equipped with special dual tires. Lifting Speed with VFM/VFHM : For FG/FD15T13 - FG/FD15C13 - FG/FD18T3 - FG/FD18C3 - FG15T3/C3 - FG18T3/C with VFM FG 470mm/s with load. 550mm/s without load. FD 420mm/s with load. 490mm/s without load. with VFHM FG 530mm/s with load. 610mm/s without load. FD 480mm/s with load. 540mm/s without load. For FHG15T3/C - FHD15T3Z/C3Z - FHG18T3/C3 - FHD18T3Z/C3Z - FHG15T3/C3 - FHG18T3/C with VFM FG 480mm/s with load. 560mm/s without load. FD 420mm/s with load. 540mm/s without load. with VFHM FG 540mm/s with load. 620mm/s without load. FD 560mm/s with load. 600mm/s without load. Lowering speed with VFM/VFHM mast: 420mm/s with load. 370mm/s without load. Overall Vehicle lenght with VFM mast: +10mm longer than of STD model with VM mast with VFHM mast: +25mm longer than of STD model with VM mast

SPECIFICATIONS -- 2-2,5-3 ton Wide view VM Overall FG / FD 20 FG / FD 25 Lowered Raised with F / B (3) Service Weight (kg) FG / FD 20 FG / FD 25 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD VM250 2000 2000 2500 2500 2500 1780 3530 6 / 10 3170 3275 3290 3530 3635 3650 VM270 2000 2000 2500 2500 2700 1880 3730 6 / 10 3185 3290 3305 3545 3650 3665 VM300 2000 2000 2500 250 3000 2030 4030 6 / 12 3210 3315 3330 3570 3675 3690 VM330 2000 2000 2500 2500 3300 2180 4330 6 / 12 3235 3340 3355 3595 3700 3715 VM350 2000 2000 2500 2500 3500 2280 4530 6 / 12 3250 3355 3370 3610 3715 3730 VM375 2000 2000 2500 2500 3750 2405 4780 VM400 2000 2000 2500 2500 4000 2580 5030 VM425 VM450 VM475 VM500 1950 *2000 1900 *1950 1800 *1850 1650 *1700 1950 *2000 1900 *1950 1800 *1850 1650 *1700 2450 *2500 2150 *2450 1850 *2350 1700 *2250 2450 *2500 2350 *2450 2200 *2350 2000 *2250 4250 2705 5280 4500 2830 5530 4750 2955 5780 5000 3080 6030 * * 3270 3375 3390 3630 3735 3750 3325 3430 3445 3685 3790 3805 3345 3450 3465 3705 3810 3825 3365 3470 3485 3725 3830 3845 3385 3490 3505 3745 3850 3865 3405 3510 3525 3765 3870 3885 VM550 *1700 *1700 5500 3380 6530 *3 / 6 3480 3585 3600 3840 3945 3960 VM600 *1300 *1300 *1400 *1400 6000 3630 7030 *3 / 6 3520 3625 3640 3880 3985 4000 (3) Weight for diesel model: +130kg (TD27) +110kg (C240) Wide view Full Free 2-stage VFM FG / D20 FG / D25 For height without backrest: -385mm. (2) For free lift without backrest: +385mm. Weight without backrest: -20kg. (3) Weight for diesel model: +130kg (TD27) +110kg(C240) Overall Lowered Raised with (2) Free Lift with (3) Service Weight (kg) FG20 FG25 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD VFM250 2000 2000 2500 2500 2500 1780 3530 780 6-10 3225 3330 3345 3585 3690 3705 VFM270 2000 2000 2500 2500 2700 1880 3730 880 6-10 3245 3350 3365 3605 3710 3725 VFM300 2000 2000 2500 2500 3000 2030 4030 1030 6-12 3270 3375 3390 3630 3735 3750 VFM330 2000 2000 2500 2500 3300 2180 4330 1180 6-12 3295 3400 3415 3655 3760 3775 VFM350 2000 2000 2500 2500 3500 2280 4530 1280 6-12 3310 3415 3430 3670 3775 3790 VFM375 2000 2000 2500 2500 3750 2405 4780 1405 6-6 3330 3435 3450 3690 3795 3810 *6-12 VFM400 2000 2000 2500 2500 4000 2580 5030 1580 6-6 3390 3495 3510 3750 3855 3870 *6-12 VFM425 1950 1950 2450 2450 4250 2705 5280 1705 6-6 3410 3515 3530 3770 3875 3890 *2000 *2000 *2500 *2500 *6-12 VFM450 1900 1900 2150 2350 4500 2830 5530 1830 6-6 3435 3540 3555 3795 3900 3915 *1950 *1950 *2450 *2450 *6-12 VFM475 1800 1800 1850 2200 4750 2955 5780 1955 6-6 3455 3560 3575 3815 3920 3935 *1850 *1850 *2350 *2350 *6-6 VFM500 1650 1700 1700 2000 5000 3080 6030 2080 6-6 3475 3580 3595 3835 3940 3955 *1700 *2250 *2250 *6-6 VFM550 *1700 *1700 5500 3380 6530 2380 *3-6 3555 3660 3675 3915 4020 4035 VFM600 *1300 *1300 *1400 *1400 6000 3630 7030 2630 *3-6 3595 3700 3715 3955 4060 4075

Wide view Full Free 3-stage VFHM FG / D20 FG / D25 Overall Lowered Raised with (2) Free Lift with F/B FG20 (3) Service Weight (kg) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD VFHM360 2000 2000 2500 2500 3600 1780 4630 780 6-6 3365 3470 3485 3725 3830 3845 *6-10 VFHM400 2000 2000 2500 2500 4000 1905 5030 905 6-6 3395 3500 3515 3755 3860 3875 *6-10 VFHM435 1900 1900 2200 2300 4350 2030 5380 1030 6-6 3425 3530 3545 3785 3890 3905 *2000 *2000 *2400 *2400 *6-10 VFHM480 1700 1800 1900 2200 4800 2180 5830 1180 6-6 3455 3560 3575 3815 3920 3935 *1900 *1900 *2300 *2300 *6-10 VFHM500 1500 1750 1600 2000 5000 2280 6030 1280 6-6 3480 3585 3600 3840 3945 3960 *1800 *1800 *2250 *2250 *6-10 VFHM540 1200 1650 1300 1700 5400 2405 6430 1405 3-6 3510 3615 3630 3870 3975 3990 *1750 *1750 *2150 *2150 *3-6 VFHM600 900 1100 950 1100 6000 2630 7030 1630 3-6 3605 3710 3725 3965 4070 4085 *1650 *1650 *1800 *1800 *3-6 VFHM650 *1550 *1550 6500 2845 7530 1845 *3-3 3660 3765 3780 4020 4125 4140 VFHM700 *1250 *1250 *1250 *1250 7000 3065 8030 2065 *3-3 3715 3820 3835 4075 4180 4195 FG25 For height without backrest: -455mm. (2) For free lift without backrest: +455mm. Weight without backrest: -20kg. (3) Weight for diesel model: +130kg (TD27) +110kg(C240) Rated Capacity with (*): Shows capacity with DD: front dual tires. Serves Weight of VM/VFM 550-600 and of VFHM 650-700 represents the weight of vehicles equipped with SDD: special dual tires. Loading Speed with VFM/VFHM : with VFM FG 480mm/s with load. 520mm/s without load. FD 540mm/s with load. 590mm/s without load. with VFHM FG 500mm/s with load. 540mm/s without load. FD 560mm/s with load. 610mm/s without load. Lowering speed with VFM/VFHM mast: 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFHM mast: +15mm longer than that of STD model with VM/FM mast

Wide view Full Free 2-stage VFW (4 CYLINDER) FG / D20 FG / D25 For height without backrest: -455mm. (2) For free lift without backrest: +455mm. Weight without backrest: -20kg. (3) Weight for diesel model: +130kg (TD27) +110kg(C240) Overall Lowered Raised with (2) Free Lift with F/B FG20 (3) Service Weight (kg) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD VFW300 1900 1900 2400 2400 3000 2045 4030 1045 6-12 3280 3385 3505 3640 3745 3865 VFW330 1900 1900 2400 2400 3300 2195 4330 1195 6-12 3310 3415 3535 3670 3775 3895 VFW350 1900 1900 2400 2400 3500 2295 4530 1295 6-12 3325 3430 3550 3685 3790 3910 VFW375 1800 1800 2350 2350 3750 2420 4780 1420 *6-6 3350 3455 3575 3710 3815 3935 *1900 *1900 6-12 VFW400 1800 1800 2300 2300 4000 2595 5030 1595 *6-6 3410 3515 3635 3770 3875 3995 *1900 *1900 *2350 *2350 6-12 FG25 Wide view Full Free 3-stage VFHW (4 CYLINDER) FG / D20 FG / D25 Overall Lowered Raised with (2) Free Lift with F/B FG20 (3) Service Weight (kg) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD VHW435 1800 1850 2200 2300 4350 2045 5380 1045 *6-6 3425 3530 3650 3785 3890 4010 *1900 *1900 *2400 *2400 6-10 VHW480 1700 1800 1900 2200 4800 2195 5830 1195 *6-6 3470 3575 3695 3830 3935 4055 *1900 *1900 *2300 *2300 6-10 VHW500 1500 1750 1600 2000 5000 2295 6030 1295 *6-6 3495 3600 3720 3855 3960 4080 *1800 *1800 *2250 *2250 6-10 VHW540 1200 1650 1300 1700 5400 2420 6430 1420 3-6 3520 3625 3745 3880 3985 4105 *1750 *1750 *2150 *2150 VHW550 1150 1600 1250 1600 5500 2460 6530 1460 3-6 3530 3635 3755 3890 3995 4115 *1750 *1750 *2100 *2100 FG25 For height without backrest: -455mm. (2) For free lift without backrest: +455mm. Weight without backrest: -20kg. (3) Weight for diesel model: +130kg (TD27) +110kg(C240) Rated Capacity with (*): Shows capacity with DD: front dual tires. Lifting Speed with VFM/VFHM : with VFM FG 450mm/s with load. 490mm/s without load. FD 520mm/s with load. 570mm/s without load. with VFHM FG 460mm/s with load. 510mm/s without load. FD 540mm/s with load. 590mm/s without load. Lowering speed with VFM/VFHM mast: 420mm/s with load. 380mm/s without load. Overall Vehicle lenght with VFW/VFHW (4CYLINDER) mast: +35mm longer than that of STD model with VM mast

Wide view VM FG / D30 Overall Lowered Raised with F/B (3) Service Weight (kg) FG30 PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD VM250 3000 3000 2500 1820 3760 6-10 4210 4245 4360 VM270 3000 3000 2700 1920 3960 6-10 4225 4260 4375 VM300 3000 3000 3000 2075 4260 6-12 4250 4285 4400 VM330 3000 3000 3300 2225 4560 6-12 4275 4310 4425 VM350 3000 3000 3500 2325 4760 6-12 4290 4325 4440 VM375 3000 3000 3750 2450 5010 6-6 4310 4345 4460 *6-12 VM400 3000 3000 4000 2625 5260 6-6 4370 4405 4520 *6-12 VM425 2900 3000 4250 2750 5510 6-6 4390 4425 4540 *3000 *6-12 VM450 2800 3000 4500 2875 5760 6-6 4410 4445 4560 *3000 *6-12 VM475 2750 2950 4750 3000 6010 6-6 4430 4465 4580 *2900 *2900 *6-6 VM500 2700 2850 5000 3125 6260 *6-6 4455 4490 4605 *2850 *2850 6-6 VM550 *2400 *2400 5500 3425 6760 *3-6 4530 4565 4680 VM600 *2000 *2000 6000 3675 7260 *3-6 4570 4605 4720 (3) Weight for diesel model: +140kg (TD27) +120kg (C240) Wide view Full Free 2-stage VFM FG / D30 Overall Lowered Raised with (2) Free lift with F/B (3) Service Weight (kg) FG30 PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD VM250 3000 3000 2500 1820 3760 600 6-10 4210 4245 4360 VM270 3000 3000 2700 1920 3960 700 6-10 4225 4260 4375 VM300 3000 3000 3000 2075 4260 850 6-12 4250 4285 4400 VM330 3000 3000 3300 2225 4560 6-12 4275 4310 4425 VM350 3000 3000 3500 2325 4760 1100 6-12 4290 4325 4440 VM375 3000 3000 3750 2450 5010 1225 6-6 4310 4345 4460 *6-12 VM400 3000 3000 4000 2625 5260 1400 6-6 4370 4405 4520 *6-12 VM425 2900 3000 4250 2750 5510 1525 6-6 4390 4425 4540 *3000 *6-12 VM450 2800 3000 4500 2875 5760 1650 6-6 4410 4445 4560 *3000 *6-12 VM475 2750 2950 4750 3000 6010 1775 6-6 4430 4465 4580 *2900 *2900 6-6 VM500 2700 2850 5000 3125 6260 1900 *6-6 4455 4490 4605 *2850 *2850 6-6 VM550 *2400 *2400 5500 3425 6760 2200 *3-6 4530 4565 4680 VM600 *2000 *2000 6000 3675 7260 2450 *3-6 4570 4605 4720 For height without backrest: -540mm. (2) For free lift without backrest: +540mm. Weight without backrest: -30kg. (3) Weight for diesel model: +140kg (TD27) +120kg(C240)

Wide view Full Free 3-stage VFHM FG / D30 Overall Lowered Raised with (2) Free lift with F/B (3) Service Weight (kg) FG30 PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD VFHM360 3000 3000 3600 1825 4860 600 6-6 4395 4430 4545 *6-10 VFHM400 3000 3000 4000 1950 5260 725 6-6 4425 4460 4575 *6-10 VFHM435 2900 2900 4350 2075 5610 850 6-6 4460 4495 4610 *3000 *3000 *6-10 VFHM480 2800 2800 4800 2225 6060 6-6 4495 4530 4645 *2900 *2900 *6-10 VFHM500 2600 2750 5000 2325 6260 1100 6-6 4520 4555 4670 *2750 *2750 *6-10 VFHM540 1900 2500 5400 2450 6660 1225 3-6 4555 4590 4705 *2650 *2650 *3-6 VFHM600 1400 1850 6000 2675 7260 1450 3-6 4650 4685 4800 *2100 *2100 *3-6 VFHM650 *1700 *1700 6500 2890 7760 1665 *3-3 4715 4750 4865 VFHM700 7000 3110 8260 1885 *3-3 4770 4805 4920 For height without backrest: -580mm. (2) For free lift without backrest: +580mm. Weight without backrest: -30kg. (3) Weight for diesel model: +140kg (TD27) +120kg(C240) Rated Capacity with (*): Shows capacity with DD: front dual tires. Serves Weight of VM/VFM 550-600 and of VFHM 650-700 represents the weight of vehicles equipped with SDD: special dual tires. Lifting Speed with VFM/VFHM : with VFM FG 420mm/s with load. 440mm/s without load. FD 460mm/s with load. 530mm/s without load. with VFHM FG 430mm/s with load. 450mm/s without load. FD 480mm/s with load. 550mm/s without load. Lowering speed with VFM/VFHM mast: 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFHM mast: +15mm longer than that of STD model with VM/FM mast

Wide view Full Free 2-Stage VFW (4CYLINDER) FG / D30 Overall Lowered Raised with (2) Free lift with F/B (3) Service Weight (kg) FG30 PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD VFW300 2900 2900 3000 2125 4260 900 6-12 4310 4345 4495 VFW330 2900 2900 3300 2275 4560 1050 6-12 4335 4370 4520 VFW350 2900 2900 3500 2375 4760 1150 6-12 4355 4390 4540 VFW375 2900 2900 3750 2500 5010 1275 6-6 4375 4410 4560 *6-12 VFW400 2900 2900 4000 2675 5260 1450 6-6 4440 4475 4625 *6-12 For height without backrest: -580mm. (2) For free lift without backrest: +580mm. Weight without backrest: -30kg. (3) Weight for diesel model: +140kg (TD27) +120kg(C240) Wide view Full Free 3-Stage VFHW (4CYLINDER) FG / D30 Overall Lowered Raised with (2) Free lift with F/B (3) Service Weight (kg) FG30 PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD VHW435 2800 2900 4350 2125 5610 900 6-6 4470 4505 4655 *2900 *6-10 VHW480 2700 2800 4800 2275 6060 1050 6-6 4510 4545 4695 *2800 *6-10 VHW500 2600 2750 5000 2375 6260 1150 6-6 4535 4570 4720 *2750 *6-10 VHW540 1900 2500 5400 2500 6660 1275 3-6 4565 4600 4750 *2650 *2650 VHW550 1900 2350 5500 2540 6760 1315 3-6 4575 4610 4760 *2600 *2600 For height without backrest: -580mm. (2) For free lift without backrest: +580mm. Weight without backrest: -30kg. (3) Weight for diesel model: +140kg (TD27) +120kg(C240) Rated Capacity with (*): Shows capacity with DD: front dual tires. Lifting Speed with VFM/VFHM : with VFM FG 360mm/s with load. 420mm/s without load. FD 430mm/s with load. 500mm/s without load. with VFHM FG 380mm/s with load. 430mm/s without load. FD 450mm/s with load. 520mm/s without load. Lowering speed with VFM/VFHM mast: 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFHM mast: +35mm/+45mm longer than that of STD model with VM mast

Wide view VM FHG / D20T3 FHG / D20C3 FHG / D25T3 FHG / D25C3 FHG / D30T3 FHG / D30C3 Overall Lowered Raised with F/B FHG 20T3 FHG 20C3 (2) Service Weight (kg) FHG 25T3 FHG 25C3 FHG 30T3 FHG 30C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD S DD SDD VM250 2000 2000 2500 2500 3000 3000 2500 1780 3530 6-10 3180 3285 3300 3540 3645 3660 4220 4255 4370 VM270 2000 2000 2500 2500 3000 3000 2700 1880 3730 6-10 3195 3300 3315 3555 3660 3675 4235 4270 4385 VM300 2000 2000 2500 2500 3000 3000 3000 2030 4030 6-12 3220 3325 3340 3580 3685 3700 4260 4295 4410 VM330 2000 2000 2500 2500 3000 3000 3300 2180 4330 6-12 3245 3350 3365 3605 3710 3725 4285 4320 4435 VM350 2000 2000 2500 2500 3000 3000 3500 2280 4530 6-12 3260 3365 3380 3620 3725 3740 4300 4335 4450 VM375 2000 2000 2500 2500 3000 3000 3750 2405 4780 6-6 3280 3385 3400 3640 3745 3760 4320 4355 4470 *6-12 VM400 2000 2000 2500 2500 3000 3000 4000 2580 5030 6-6 3335 3440 3455 3695 3800 3815 4380 4415 4530 *6-12 VM425 1950 1950 2450 2450 2900 3000 4250 2705 5280 6-6 3355 3460 3475 3715 3820 3835 4400 4435 4550 *2000 *2000 *2500 *2500 *3000 *6-12 VM450 1900 1900 2150 2350 2800 3000 4500 2830 5530 6-6 3375 3480 3495 3735 3840 3855 4420 4455 4570 *1950 *1950 *2450 *2450 *3000 *6-12 VM475 1800 1800 1850 2200 2750 2950 4750 2955 5780 6-6 3395 3500 3515 3755 3860 3875 4440 4475 4590 *1850 *1850 *2350 *2350 *2900 *2900 *6-6 VM500 1650 1700 1700 2000 2700 2850 5000 3080 6030 6-6 3415 3520 3535 3775 3880 3895 4465 4500 4615 *1700 *2250 *2250 *2850 *6-6 VM550 *1700 *1700 *2400 *2400 5500 3380 6530 *3-6 3490 3595 3610 3850 3955 3970 4540 4575 4690 VM600 *1300 *1300 *1400 *1400 *2000 *2000 6000 3630 7030 *3-6 3530 3635 3650 3890 3995 4010 4580 4615 4730 Figures for (2t; 2,5t model). For (3t model) +45mm (2) Weight for diesel model: (2t model) +120kg, (2,5t model) +120kg, (3t model) +130 kg. Wide view Full Free 2-stage VFM FHG / D20T3 FHG / D20C3 FHG / D25T3 FHG / D25C3 FHG / D30T3 FHG / D30C3 Overall (2) Raised with Lowered (3) Free lift with F/B FHG 20T3 FHG 20C3 (4) Service Weight (kg) FHG 25T3 FHG 25C3 FHG 30T3 FHG 30C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD S DD SDD VM250 2000 2000 2500 2500 3000 3000 2500 1780 3530 780 6-10 3235 3340 3355 3595 3700 3715 4260 4295 4410 VM270 2000 2000 2500 2500 3000 3000 2700 1880 3730 880 6-10 3255 3360 3375 3615 3720 3735 4275 4310 4425 VM300 2000 2000 2500 2500 3000 3000 3000 2030 4030 1030 6-12 3280 3385 3400 3640 3745 3760 4305 4340 4455 VM330 2000 2000 2500 2500 3000 3000 3300 2180 4330 1180 6-12 3305 3410 3425 3665 3770 3785 4330 4365 4480 VM350 2000 2000 2500 2500 3000 3000 3500 2280 4530 1280 6-12 3320 3425 3440 3680 3785 3800 4345 4380 4495 VM375 2000 2000 2500 2500 3000 3000 3750 2405 4780 1405 6-6 3340 3445 3460 3700 3805 3820 4370 4405 4520 *6-12 VM400 2000 2000 2500 2500 3000 3000 4000 2580 5030 1580 6-6 3400 3505 3520 3760 3865 3880 4435 4470 4585 *6-12 VM425 1950 1950 2450 2450 2900 3000 4250 2705 5280 1705 6-6 3420 3525 3540 3780 3885 3900 4455 4490 4605 *2000 *2000 *2500 *2500 *3000 *6-12 VM450 1900 1900 2150 2350 2800 3000 4500 2830 5530 1830 6-6 3445 3550 3565 3805 3910 3925 4475 4510 4625 *1950 *1950 *2450 *2450 *3000 *6-12 VM475 1800 1800 1850 2200 2750 2950 4750 2955 5780 1955 6-6 3465 3570 3585 3825 3930 3945 4500 4535 4650 *1850 *1850 *2350 *2350 *2900 *2900 *6-6 VM500 1650 1700 1700 2000 2700 2850 5000 3080 6030 2080 6-6 3485 3590 3605 3845 3950 3965 4520 4555 4670 *1700 *2250 *2250 *2850 *6-6 VM550 *1700 *1700 *2400 *2400 5500 3380 6530 2380 *3-6 3565 3670 3685 3925 4030 4045 4605 4640 4755 VM600 *1300 *1300 *1400 *1400 *2000 *2000 6000 3630 7030 2630 *3-6 3605 3710 3725 3965 4070 4085 4650 4685 4800 Figures for (2t, 2.5t model); For (3t model) +45mm (2) Figures for (2t, 2.5t model); For (3t model) +230mm. / For height without backrest: (2t, 2.5t model) -455mm, (3t model) -580 mm (3) Figures for (2t, 2.5t model); For (3t model) -180mm. / For free lift without backrest: (2t, 2.5t model) +455mm, (3t model) +580 mm. / Weight for without backrest: (2t, 2.5t model) -20kg, (3t model) -30kg (4) Weight for diesel model: (2t model) +120kg, (2.5t model) +120kg, (3t model) +130kg.

Wide view Full Free 3-stage VFHM FHG / D20T3 FHG / D20C3 FHG / D25T3 FHG / D25C3 FHG / D30T3 FHG / D30C3 Overall (2) Raised with Lowered (3) Free lift with F/B FHG 20T3 FHG 20C3 (4) Service Weight (kg) FHG 25T3 FHG 25C3 FHG 30T3 FHG 30C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD S DD SDD VFHM360 2000 2000 2500 2500 3000 3000 3600 1780 4630 780 6-6 3375 3480 3495 3735 3840 3855 4405 4440 4555 *6-10 VFHM400 2000 2000 2500 2500 3000 3000 4000 1905 5030 905 6-6 3405 3510 3525 3765 3870 3885 4435 4470 4585 *6-10 VFHM435 1900 1900 2200 2300 2900 2900 4350 2030 5380 1030 6-6 3435 3540 3555 3795 3900 3915 4470 4505 4620 *2000 *2000 *2400 *2400 *3000 *3000 *6-10 VFHM480 1700 1800 1900 2200 2800 2800 4800 2180 5830 1180 6-6 3465 3570 3585 3825 3930 3945 4505 4540 4655 *1900 *1900 *2300 *2300 *2900 *2900 *6-10 VFHM500 1500 1750 1600 2000 2600 2750 5000 2280 6030 1280 6-6 3490 3595 3610 3850 3955 3970 4530 4565 4680 *1800 *1800 *2550 *2250 *2750 *2750 *6-10 VFHM540 1200 1650 1300 1700 1900 2500 5400 2405 6430 1405 3-6 3520 3625 3640 3880 3985 4000 4565 4600 4715 *1750 *1750 *2150 *2150 *2650 *2650 *3-6 VFHM600 900 1100 950 1100 1400 1850 6000 2630 7030 1630 3-6 3615 3720 3735 3975 4080 4095 4660 4695 4810 *1650 *1650 *1800 *1800 *2100 *2100 *3-6 VFHM650 *1550 *1550 *1700 *1700 6500 2845 7530 1845 *3-3 3670 3775 3790 4030 4135 4150 4725 4760 4875 VFHM700 *1250 *1250 *1250 *1250 7000 3065 8030 2065 *3-3 3725 3830 3845 4085 4190 4205 4780 4815 4930 Figures for (2t, 2.5t model); For (3t model) +45mm (2) Figures for (2t, 2.5t model); For (3t model) +230mm. For height without backrest: (2t, 2.5t model) -455mm, (3t model) -580 mm (3) Figures for (2t, 2.5t model); For (3t model) -180mm. For free lift without backrest: (2t, 2.5t model) +455mm, (3t model) +580 mm. Weight for without backrest: (2t, 2.5t model) -20kg, (3t model) -30 kg (4) Weight for diesel model: (2t model) +120kg, (2.5t model) +120kg, (3t model) +130 kg. Rated Capacity with (*): Shows capacity with DD: front dual tires. Service weight of VM/VFM 550-600 and of VFHM 650-700 represents the weight of vehicles equipped with SDD: special dual tires. Lifting Speed with VFM/VFHM : with VFM FG (2t, 2.5t model) 530mm/s with load. 560mm/s without load. FD (2t, 2.5t model) 550mm/s with load. 580mm/s without load. FG (3t model) 450mm/s with load. 470mm/s without load. FD (3t model) 470mm/s with load. 490mm/s without load. with VFHM FG (2t, 2.5t model) 560mm/s with load. 580mm/s without load. FD (2t, 2.5t model) 570mm/s with load. 600mm/s without load. FG (3t model) 460mm/s with load. 480mm/s without load. FD (3t model) 480mm/s with load. 500mm/s without load. Lowering speed with VFM/VFHM mast: (2t, 2.5t model) 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFM mast: +15mm longer than of STD model with VM mast

Wide view Full Free 2-stage VFW (4CYLINDER) FHG / D20T3 FHG / D20C3 FHG / D25T3 FHG / D25C3 FHG / D30T3 FHG / D30C3 Overall (2) Raised with Lowered (3) Free lift with F/B FHG 20T3 FHG 20C3 (4) Service Weight (kg) FHG 25T3 FHG 25C3 FHG 30T3 FHG 30C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD S DD SDD VFW300 1900 1900 2400 2400 2900 2900 3000 2045 4030 1045 6-12 3290 3395 3515 3650 3755 3875 4320 4355 4505 VFW330 1900 1900 2400 2400 2900 2900 3300 2195 4330 1195 6-12 3320 3425 3545 3680 3785 3905 4345 4380 4530 VFW350 1900 1900 2400 2400 2900 2900 3500 2295 4530 1295 6-12 3335 3440 3560 3695 3800 3920 4365 4400 4550 VFW375 1800 1800 2350 2350 2900 2900 3750 2420 4780 1420 *6-6 3360 3465 3585 3720 3825 3945 4385 4420 4570 *1900 *1900 6-12 VFW400 1800 1800 2300 2300 2900 2900 4000 2595 5030 1595 *6-6 3420 3525 3645 3780 3885 4005 4450 4485 4635 *1900 *1900 *2350 *2350 6-12 Figures for (2t, 2.5t model); For (3t model) +80mm (2) Figures for (2t, 2.5t model); For (3t model) +230mm. For height without backrest: (2t, 2.5t model) -455mm, (3t model) -580 mm (3) Figures for (2t, 2.5t model); For (3t model) -145mm. For free lift without backrest: (2t, 2.5t model) +455mm, (3t model) +580 mm. Weight for without backrest: (2t, 2.5t model) -20kg, (3t model) -30 kg (4) Weight for diesel model: (2t model) +120kg, (2.5t model) +120kg, (3t model) +130 kg. Wide view Full Free 3-stage VFHW (4CYLINDER) FHG / D20T3 FHG / D20C3 FHG / D25T3 FHG / D25C3 FHG / D30T3 FHG / D30C3 Overall (2) Raised with Lowered (3) Free lift with F/B FHG 20T3 FHG 20C3 (4) Service Weight (kg) FHG 25T3 FHG 25C3 FHG 30T3 FHG 30C3 PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD S DD SDD VHW435 1800 1850 2200 2300 2800 2900 4350 2045 5380 1045 *6-6 3435 3540 3660 3795 3900 4020 4480 4515 4665 *1900 *1900 *2400 *2400 *2900 6-10 VHW480 1700 1800 1900 2200 2700 2800 4800 2195 5830 1195 *6-6 3480 3585 3705 3840 3945 4065 4520 4555 4705 *1900 *1900 *2300 *2300 *2800 6-10 VHW500 1500 1750 1600 2000 2600 2750 5000 2295 6030 1295 *6-6 3505 3610 3730 3865 3970 4090 4545 4580 4730 *1800 *1800 *2250 *2250 *2750 6-10 VHW540 1200 1650 1300 1700 1900 2500 5400 2420 6430 1420 3-6 3530 3635 3755 3890 3995 4115 4575 4610 4760 *1750 *1750 *2150 *2150 *2650 *2650 VHW550 1150 1600 1250 1600 1900 2350 5500 2460 6530 1460 3-6 3540 3645 3765 3900 4005 4125 4585 4620 4770 *1750 *1750 *2100 *2100 *2600 *2600 Figures for (2t, 2.5t model); For (3t model) +80mm (2) Figures for (2t, 2.5t model); For (3t model) +230mm. For height without backrest: (2t, 2.5t model) -455mm, (3t model) -580 mm (3) Figures for (2t, 2.5t model); For (3t model) -145mm. For free lift without backrest: (2t, 2.5t model) +455mm, (3t model) +580 mm. Weight for without backrest: (2t, 2.5t model) -20kg, (3t model) -30 kg (4) Weight for diesel model: (2t model) +120kg, (2.5t model) +120kg, (3t model) +130 kg. Rated Capacity with (*): Shows capacity with DD: front dual tires. Lifting Speed with VFM/VFHM : with VFM FG (2t, 2.5t model) 450mm/s with load. 490mm/s without load. FD (2t, 2.5t model) 510mm/s with load. 540mm/s without load. FG (3t model) 410mm/s with load. 470mm/s without load. FD (3t model) 430mm/s with load. 460mm/s without load. with VFHM FG (2t, 2.5t model) 460mm/s with load. 510mm/s without load. FD (2t, 2.5t model) 530mm/s with load. 560mm/s without load. FG (3t model) 430mm/s with load. 460mm/s without load. FD (3t model) 450mm/s with load. 480mm/s without load. Lowering speed with VFM/VFHM mast: (2t, 2.5t, 3t model) 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFW/VFHW (4cylinder) mast (2t, 2,5t model): +35mm longer than of STD model with VM mast (3t model): +35mm/+45mm longer than of STD model with VM mast

SPECIFICATIONS -- 3,5 ton Wide view VM Overall F / B (3) Service weight (kg) Raised with FD35T3S Lowered FD35T3S PNEUMATIC UNIQUE(SE) mm mm mm deg S DD VM250 3500 3500 2500 1885 3760 6 / 10 4890 4905 VM270 3500 3500 2700 1985 3960 6 / 10 4910 4925 VM300 3500 3500 3000 2135 4260 6 / 12 4940 4955 VM330 3500 3500 3300 2285 4560 6 / 12 4970 4985 VM350 3500 3500 3500 2385 4760 6 / 12 4990 5005 VM375 3500 3500 3750 2510 5010 5010 5025 VM400 3500 3500 4000 2685 5260 5080 5095 VM425 3500 3500 4250 2810 5510 5105 5120 VM450 3400 3450 4500 2935 5760 5125 5140 VM475 3400 3400 4750 3060 6010 5150 5165 VM500 3300 3350 5000 3185 6020 5175 5190 VM550 *3200 *3200 5500 3485 6760 *3 / 6 5265 VM600 *2400 *2400 6000 3735 7260 *3 / 6 5310 Wide View Full Free 2-stage VFM (3) Overall (2) Free lift Service weight (kg) Raised with FD35T3S Lowered with F / B FD35T3S PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD VFM250 3500 3500 2500 1885 3760 655 6 / 10 4890 4995 VFM270 3500 3500 2700 1985 3960 755 6 / 10 5000 5015 VFM300 3500 3500 3000 2135 4260 905 6 / 12 5030 5045 VFM330 3500 3500 3300 2285 4560 1055 6 / 12 5065 5080 VFM350 3500 3500 3500 2385 4760 1155 6 / 12 5085 5100 VFM375 3500 3500 3750 2510 5010 1280 5115 5130 VFM400 3500 3500 4000 2685 5260 1455 5185 5200 VFM425 3500 3500 4250 2810 5510 1580 5215 5230 VFM450 3400 3450 4500 2935 5760 1705 5240 5255 VFM475 3400 3400 4750 3060 6010 1830 5265 5280 VFM500 3300 3350 5000 3185 6020 1955 5295 5310 VFM550 *3200 *3200 5500 3485 6760 2255 *3 / 6 5390 VFM600 *2400 *2400 6000 3735 7260 2505 *3 / 6 5445 For height without backrest: -445mm (2) For free lift without backrest: +455mm Weight for diesel model: -30kg Wide View Full Free 3-stage VFHM (3) Overall (2) Free lift Service weight (kg) Raised with FD35T3S Lowered with F / B FD35T3S PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD VFHM 360 3400 3400 3600 1885 4860 655 *6 / 10 5095 5110 VFHM 400 3400 3400 4000 2010 5260 780 *6 / 10 5130 5145 VFHM 435 3300 3300 4350 2135 5610 905 *6 / 10 5160 5175 VFHM 480 3200 3250 4800 2285 6060 1055 *6 / 10 5200 5215 VFHM 500 3100 3200 5000 2385 6260 1155 *6 / 10 5230 5245 VFHM 540 2500 - *2900 2700 - *2900 5400 2510 6660 1280 3 / 6 *3 / 6 5260 5275 VFHM 600 1600 - *2400 2000 - *2400 6000 2735 7260 1505 3 / 6 *3 / 6 5370 5385 VFHM 650 *2000 *2000 6500 2950 7760 1720 3 / 6 5435 VFHM 700 *1600 *1600 7000 3170 8260 1940 3 / 6 5495 For height without backrest: -530mm (2) For free lift without backrest: +530mm Weight for diesel model: -30kg Rated Capacity with (*): Shows capacity with DD: front dual tires. Lifting Speed with VFM/VFHM : with VFM 530mm/s with load. 560mm/s without load. with VFHM 560mm/s with load. 580mm/s without load. Lowering speed with VFM/VFHM mast: 440mm/s with load. 380mm/s without load. Overall Vehicle lenght with VFHM mast: +15mm longer than of STD model with VM/VFM mast

STANDARD DIMENSIONS (Front Single Tire) GROUND CLEARANCE FD/FG15 FHD/FHG15 FD/FG18 FHD/FHG18 mm mm 110 110 Frame 105 105 Front axle 125 125 Rear axle 125 125 Counter weight 135 135 FD/FG15 FHD/FHG15 FD/FG18 FHD/FHG18 mm mm Overall height, raised (with backrest) 4030 4030 fork height 3000 3000 height, lowered 1995 1995 height Free lift 155 155 thickness 35 35 Min. ground clearance 125 125 Overall length (with fork) 3165 3195 Length to fork face 2245 2275 length 920 920 Load distance 395 395 Wheelbase 1425 1425 Rear overhang 425 455 Drawbar Pin Center 495 495 Overhead guard clearance (from face of seat)** FD / FG15 18 = 1035 FHD / FHG15 18 = 1005 Overall height (overhead guard)** 2070 2070 Overall width 1070 1100 spread (outside) 200-920 200-920 Tread (front) 890 920 Tread (rear) 920 920 width 100 100 Inside turning radius 110 95 Outside turning radius 1980 2010 Min. intersecting aisle 1780 1800 Tilt angles (forward-backward) 6-12 6-12 ** European (EXE) and Scandinavian export trucks (EXN): +60mm DIMENSIONS WITH FRONT DUAL DRIVE WHEELS (option) FD/FG15 FHD/FHG15 FD/FG18 FHD/FHG18 Tire size (front dual Type: DD) 4 x 4,50-12 - 8PR JL mm mm Overall width 1255 1255 Tread (front) 980 980 Inside turning radius 90 90 Outside turning radius 2020 2050 Min. intersecting aisle 1840 1860 Tire size (front dual Type: SDD) 4 x 6,50-10 - 10PR JL mm mm Overall width 1512 1512 Tread (front) 1110 1110 Inside turning radius 90 90 Outside turning radius 2095 2120 Min. intersecting aisle 1940 1960

STANDARD DIMENSIONS (Front Single Tire) GROUND CLEARANCE FD/FG20-25 FD/FG30 FHD/FHG20-25 FHD/FHG30 FD35T3S mm mm mm 110 140 145 Frame 120 145 190 Front axle 125 145 165 Rear axle 150 175 85 Counter weight 155 185 225 FD/FG20 FHD/FHG20 FD/FG25 FHD/FHG25 FD/FG30 FHD/FHG30 FD35T3S mm mm mm mm Overall height, raised (with backrest) 4030 4030 4260 4255 fork height 3000 3000 3000 3000 height, lowered 2030 2030 2075 2135 height 1220 1220 Free lift 105 110 165 170 thickness 36 40 45 50 Min. ground clearance 125 125 145 145 Overall length (with fork) 3555 3625 3775 3870 Length to fork face 2485 2555 2705 2800 length 1070 1070 1070 1070 Load distance 450 450 480 495 Wheelbase 1600 1600 1700 1700 Rear overhang 435 505 525 605 Drawbar Pin Center 530 530 560 610 Overhead guard clearance (from face of seat)** 1005 1005 1005 1005 Overall height (overhead guard)** 2070 2070 2090 2140 Overall width 1150 1150 1225 1290 spread (outside) 245-1020 245-1020 250-1090 300-1090 Tread (front) 970 970 1060 Tread (rear) 970 970 970 970 width 122 122 125 150 Inside turning radius 160 160 200 200 Outside turning radius 2170 2240 2400 2470 Min. intersecting aisle 2210 2230 2330 2390 Tilt angles (forward-backward) 6-12 6-12 6-12 6-12 ** European (EXE) and Scandinavian export trucks (EXN): +60mm DIMENSIONS WITH FRONT DUAL DRIVE WHEELS (option) FD/FG20 FHD/FHG20 FD/FG25 FHD/FHG25 FD/FG30 FHD/FHG30 FD35T3S Tire size (front dual Type: DD) 4 x 5,50-15 - 8PR (l) 4 x 6,00-15 - 10PR (l) mm mm mm mm Overall width 1480 1480 1520 1600 Tread (front) 1130 1130 1170 1600 Inside turning radius 100 100 100 100 Outside turning radius 2240 2310 2430 2540 Min. intersecting aisle 2320 2340 2445 2500 Tire size (front dual Type: SDD) 4 x 7,00-12 - 12PR (l) 4 x 28 x 9-15 - 12PR (l) mm mm mm mm Overall width 1590 1590 1950 Tread (front) 1190 1190 1435 Inside turning radius 100 100 100 Outside turning radius 2280 2350 2500 Min. intersecting aisle 2350 2370 2490

STANDARD SPECIFICATIONS Gasoline -- 1,5-1,8 ton Engine and Transmission Chassis Weight Performance Dimensions Characteristics I Manufacturer TCM 2 FG15C13 FG15T13 FG18C13 FG18T13 3 Load Capacity kg 1500 1750 4 Load Center mm 500 5 Power Type Gasoline 6 Operation Position Seated 7 Tire Type Front / Rear Pneumatic 8 Wheels (X=driven) Front / Rear 2X / 2 9 Maximum mm 3000 10 Free Lift mm 155 13 Size L x W x T mm 920 x 100 x 35 Spread (Outside) / Min. mm 920 / 200 14 Tilt Fwd / Bwd deg 6-12 15 Length to Face mm 2245 2275 16 Overall Width mm 1070 1100 17 Lowered mm 1995 18 Raised mm 4030 19 Overhead Guard (EXB, EXK) mm 2070 Overhead Guard (EXC, EXE, EXN) mm 2130 20 Operator s Seat mm 1015 21 Turning Radius (Outside) mm 1980 2010 22 Load Distance mm 395 (Centerline of front axle to front face of forks) Rear Overhang mm 425 455 23 Basic Right Stacking Aisle Width mm 3685 3715 (Add load length and clearance) 24 Speeds Travel Full load km/h 14.0 / 14.0 (Fwd/Rvs.) No load km/h 14.5 / 14.5 25 Lifting Full load mm/s 590 No load mm/s 670 26 Lowering Full load mm/s 450 No load mm/s 550 28 Drawbar Pull Full load kn 9.3 14.5 9.3 14.5 No load kn 6.9 30 Gradeability* Full load % 24 29 20 24 No load % 18 32 Total Weight kg 2510 2670 33 Weight Distribution Full load Front kg 3510 3880 Rear kg 500 540 34 No load Front kg 1070 1030 Rear kg 1440 1640 35 Tires Number Front / Rear 2 / 2 36 Size Front 6.50-10 10PR 37 Rear 5.00-8 - 8PR 38 Wheelbase mm 1425 39 Tread Front mm 890 920 Rear mm 920 mm 1045 Overhead Guard Clearance mm 1035 Counterweight mm 1110 Drawbar Pin Center mm 495 Step / Floor mm 420 / 650 40 Underclearance Min. with load mm 100 41 Center of Wheelbase mm 110 42 Brake Service (Foot) Hydraulic - Foot pedal 43 Parking Mechanical - Hand lever 45 Battery Voltage / Capacity (5HR) V/AH 12 / 28 49 Internal Combustion Engine Make/ NISSAN K15 Rated Horsepower / r.p.m. kw 25.0 / 2250 Rated Torque / r.p.m. N m 110.2 / 1600 51 Number of Cylinder 4 52 Piston Displacement cc 1486 Alternator output kw/amp 0.60 / 50 Fuel Tank Capacity Type lit 50 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd.-Rvs 2-2 1-1 2-2 1-1 57 Operating Pressure For Attachments MPa (psi) 17.7 *Computed values

Characteristics Dimensions Performance Weight Chassis Engine and Transmission I Manufacturer TCM 2 FHG15C3 FHG15T3 FHG18C3 FHG18T3 3 Load Capacity kg 1500 1750 4 Load Center mm 500 5 Power Type Gasoline 6 Operation Position Seated 7 Tire Type Front / Rear Pneumatic 8 Wheels (X=driven) Front / Rear 2X / 2 9 Maximum mm 3000 10 Free Lift mm 155 13 Size L x W x T mm 920 x 100 x 35 Spread (Outside) / Min. mm 920 / 200 14 Tilt Fwd / Bwd deg 6-12 15 Length to Face mm 2245 2275 16 Overall Width mm 1070 1100 17 Lowered mm 1995 18 Raised mm 4030 19 Overhead Guard (EXB, EXK) mm 2070 Overhead Guard (EXC, EXE, EXN) mm 2130 20 Operator s Seat mm 1045 21 Turning Radius (Outside) mm 1980 2010 22 Load Distance mm 395 (Centerline of front axle to front face of forks) Rear Overhang mm 425 455 23 Basic Right Stacking Aisle Width mm 3685 3715 (Add load length and clearance) 24 Speeds Travel Full load km/h 18.5 / 18.5 19.0 / 19.0 18.5 / 18.5 19.0 / 19.0 (Fwd/Rvs.) No load km/h 19.0 / 19.0 19.5 / 19.5 19.0 / 19.0 19.5 / 19.5 25 Lifting Full load mm/s 600 No load mm/s 680 26 Lowering Full load mm/s 450 No load mm/s 550 28 Drawbar Pull Full load kn 12.7 15.7 12.7 15.7 No load kn 6.9 30 Gradeability* Full load % 25 33 22 31 No load % 18 32 Total Weight kg 2510 2670 33 Weight Distribution Full load Front kg 3510 3880 Rear kg 500 540 34 No load Front kg 1070 1030 Rear kg 1440 1640 35 Tires Number Front / Rear 2 / 2 36 Size Front 6.50-10 10PR 37 Rear 5.00-8 - 8PR 38 Wheelbase mm 1425 39 Tread Front mm 890 920 Rear mm 920 mm 1045 Overhead Guard Clearance mm 1005 Counterweight mm 1110 Drawbar Pin Center mm 495 Step / Floor mm 420 / 650 40 Underclearance Min. with load mm 100 41 Center of Wheelbase mm 110 42 Brake Service (Foot) Hydraulic - Foot pedal 43 Parking Mechanical - Hand lever 45 Battery Voltage / Capacity (5HR) V/AH 12 / 28 49 Internal Combustion Engine Make/ NISSAN K21 Rated Horsepower / r.p.m. kw 34.6 / 2250 Rated Torque / r.p.m. N m 153.5 / 1600 51 Number of Cylinder 4 52 Piston Displacement cc 2065 Alternator output kw/amp 0.60 / 50 Fuel Tank Capacity Type lit 50 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd.-Rvs 2-2 1-1 2-2 1-1 57 Operating Pressure For Attachments MPa (psi) 17.7 *Computed values

STANDARD SPECIFICATIONS Gasoline 2-2.5-3 ton Characteristics Dimensions Performance Weight Chassis & Wheels Engine & Transmission 1 Manufacturer TCM 2 FG20C3 FG20T3 FG25C3 FG25T3 FG30C3 FG30T3 3 Load Capacity kg 2000 2500 3000 Load Center mm 500 500 500 5 Power type Gasoline Gasoline Gasoline 6 Operator Position Seated Seated Seated 7 Tire Type Front / Rear Pneumatic Pneumatic Pneumatic 8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 2x / 2 9 Maximum mm 3000 3000 3000 10 Free Lift mm 105 110 165 13 Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40 1070 x 125 x 45 Spread (Outside) / Min. mm 1020 / 244 1020 / 244 1090 / 250 14 Tilt Fwd / Bwd deg 6 / 12 6 / 12 6 / 12 15 Lenght to Face mm 2485 2555 2705 16 Overall Width mm 1150 1150 1225 17 Lowered mm 2030 2030 2075 18 Raised mm 4030 4030 4260 19 Overhead Guard (EXB, EXK) mm 2070 2070 2090 Overhead Guard (EXC, EXE, EXN) mm 2130 2130 2150 20 Operator s Seat mm 1045 1045 1070 21 Turning Radius (Outside) mm 2170 2240 2400 22 Load Distance (Centerline of Axle to Front Face of s) mm 450 450 480 Rear Overhang mm 435 505 525 23 Basic Right Stacking Aisle Width (Add load length and clearance)) mm 3925 3995 4185 24 25 Speeds Lifting 26 Lowering 28 Drawbar Pull 29 Gradeability* *Computed values Travel (Fwd. / Rvs.) Full Load km/h 18,5 18,5 19 No Load km/h 19 19 19,5 Full Load mm/s 540 540 440 No Load mm/s 580 580 490 Full Load mm/s 450 450 450 No Load mm/s 550 550 450 Full Load kn 12,3 16,7 12,3 16,7 10,8 14,2 No Load kn 8,3 8,3 9,8 Full Load % 20 28 19 24 14 18 No Load % 20 20 20 32 Total Weight kg 3210 3570 4205 Front kg 4610 5350 6350 33 Full Load Rear kg 600 720 900 Weight Distribution Front kg 1430 1370 1620 34 No Load Rear kg 1780 2200 2630 35 Number Front / Rear 2 / 2 2 / 2 2 / 2 36 Tires Front 7,00-12 - 12PR (l) 7,00-12 - 12PR (l) 28 x 9-15 - 12PR (l) Size 37 Rear 6,00-9 - 10PR (l) 6,00-9 - 10PR (l) 6,50-10 - 10PR (l) 38 Wheelbase mm 1600 1600 1700 39 Tread Front mm 970 970 Rear mm 970 970 970 mm 1040 1040 1300 Overhead Guard Clearance mm 1005 1005 1005 Counterweight mm 1110 1110 1130 Drawbar Pin Center mm 530 530 560 Step / Floor mm 435 / 650 435 / 650 460 / 680 40 Underclearance Minimum Full Load mm 110 110 140 41 Center of wheelbase mm 120 120 145 42 Brake Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal 43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever 45 Battery Voltage / Capacity (5HR) V / AH 12 / 30 12 / 30 12 / 30 49 Make - NISSAN / K21 NISSAN / K21 NISSAN / K21 50 Rated Horsepower / r.p.m. kw 34,6 / 2250 34,6 / 2250 34,6 / 2250 51 Rated Torque / r.p.m. N-m 153,5 / 1600 153,5 / 1600 153,5 / 1600 Internal Combustion Engine Number of Cylinder 4 4 4 52 Piston Displacement cc 2065 2065 2065 Alternator output kw/amp 0,60 / 50 0,60 / 50 0,60 / 50 Fuel Tank Capacity Type liter 70 70 70 55 Transmission Type Manual Power-shift Manual Power-shift Manual Power-shift Stage Fwd - Rvs 2-2 1-1 2-2 1-1 2-2 1-1 57 Operating Pressure For attachment MPa 17,7 17,7 17,7

Characteristics Dimensions Performance Weight Chassis & Wheels Engine & Transmission 1 Manufacturer TCM 2 FHG20C3 FHG20T3 FHG25C3 FHG25T3 FHG30C3 FHG30T3 3 Load Capacity kg 2000 2500 3000 Load Center mm 500 500 500 5 Power type Gasoline Gasoline Gasoline 6 Operator Position Seated Seated Seated 7 Tire Type Front / Rear Pneumatic Pneumatic Pneumatic 8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 2x / 2 9 Maximum mm 3000 3000 3000 10 Free Lift mm 105 110 165 13 Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40 1070 x 125 x 45 Spread (Outside) / Min. mm 1020 / 244 1020 / 244 1090 / 250 14 Tilt Fwd / Bwd deg 6 / 12 6 / 12 6 / 12 15 Lenght to Face mm 2485 2555 2705 16 Overall Width mm 1150 1150 1225 17 Lowered mm 2030 2030 2075 18 Raised mm 4030 4030 4260 19 Overhead Guard (EXB, EXK) mm 2070 2070 2090 Overhead Guard (EXC, EXE, EXN) mm 2130 2130 2150 20 Operator s Seat mm 1045 1045 1070 21 Turning Radius (Outside) mm 2170 2240 2400 22 Load Distance (Centerline of Axle to Front Face of s) mm 450 450 480 Rear Overhang mm 435 505 525 23 Basic Right Stacking Aisle Width (Add load length and clearance)) mm 3925 3995 4185 24 25 Speeds Lifting 26 Lowering 28 Drawbar Pull 29 Gradeability* *Computed values Travel (Fwd. / Rvs.) Full Load km/h 18,5 18,5 19 No Load km/h 19 19 19,5 Full Load mm/s 600 600 500 No Load mm/s 620 620 520 Full Load mm/s 450 450 450 No Load mm/s 550 550 450 Full Load kn 14,2 22,1 14,2 22,1 12,7 19,6 No Load kn 8,3 8,3 9,8 Full Load % 24 36 21 33 18 24 No Load % 20 18 20 32 Total Weight kg 3220 3580 4260 Front kg 4620 5350 6350 33 Full Load Rear kg 600 730 910 Weight Distribution Front kg 1440 1370 1620 34 No Load Rear kg 1780 2210 2640 35 Number Front / Rear 2 / 2 2 / 2 2 / 2 36 Tires Front 7,00-12 - 12PR (l) 7,00-12 - 12PR (l) 28 x 9-15 - 12PR (l) Size 37 Rear 6,00-9 - 10PR (l) 6,00-9 - 10PR (l) 6,50-10 - 10PR (l) 38 Wheelbase mm 1600 1600 1700 39 Tread Front mm 970 970 Rear mm 970 970 970 mm 1040 1040 1300 Overhead Guard Clearance mm 1005 1005 1005 Counterweight mm 1110 1110 1130 Drawbar Pin Center mm 530 530 560 Step / Floor mm 435 / 650 435 / 650 460 / 680 40 Underclearance Minimum Full Load mm 110 110 140 41 Center of wheelbase mm 120 120 145 42 Brake Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal 43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever 45 Battery Voltage / Capacity (5HR) V / AH 12 / 30 12 / 30 12 / 30 49 Make - NISSAN / K25 NISSAN / K25 NISSAN / K25 50 Rated Horsepower / r.p.m. kw 39,5 / 2100 39,5 / 2100 39,5 / 2100 51 Rated Torque / r.p.m. N-m 188,1 / 1600 188,1 / 1600 188,1 / 1600 Internal Combustion Engine Number of Cylinder 4 4 4 52 Piston Displacement cc 2488 2488 2488 Alternator output kw/amp 0,60 / 50 0,60 / 50 0,60 / 50 Fuel Tank Capacity Type liter 70 70 70 55 Transmission Type Manual Power-shift Manual Power-shift Manual Power-shift Stage Fwd - Rvs 2-2 1-1 2-2 1-1 2-2 1-1 57 Operating Pressure For attachment MPa 17,7 17,7 17,7

STANDARD SPECIFICATIONS Diesel -- 1.5-1.8 ton Characteristics Dimensions Performance Weight Chassis Engine and Transmission I Manufacturer TCM 2 FD15C13 FD15T13 FD18C13 FD18T13 3 Load Capacity kg 1500 1750 4 Load Center mm 500 5 Power Type Diesel 6 Operation Position Seated 7 Tire Type Front / Rear Pneumatic 8 Wheels (X=driven) Front / Rear 2X / 2 9 Maximum mm 3000 10 Free Lift mm 155 13 Size L x W x T mm 920 x 100 x 35 Spread (Outside) / Min. mm 920 / 200 14 Tilt Fwd / Bwd deg 6-12 15 Length to Face mm 2245 2275 16 Overall Width mm 1070 1100 17 Lowered mm 1995 18 Raised mm 4030 19 Overhead Guard (EXB, EXK) mm 2070 Overhead Guard (EXC, EXE, EXN) mm 2130 20 Operator s Seat mm 1015 21 Turning Radius (Outside) mm 1980 2010 22 Load Distance mm 395 (Centerline of front axle to front face of forks) Rear Overhang mm 425 455 23 Basic Right Stacking Aisle Width mm 3685 3715 (Add load length and clearance) 24 Speeds Travel Full load km/h 13.5 / 13.5 (Fwd/Rvs.) No load km/h 14.0 / 14.0 25 Lifting Full load mm/s 530 No load mm/s 600 26 Lowering Full load mm/s 450 No load mm/s 550 28 Drawbar Pull Full load kn 8.8 13.7 8.8 13.7 No load kn 6.9 30 Gradeability* Full load % 22 24 20 21 No load % 19 16 32 Total Weight kg 2540 2700 33 Weight Distribution Full load Front kg 3530 3900 Rear kg 510 550 34 No load Front kg 1090 1050 Rear kg 1450 1650 35 Tires Number Front / Rear 2 / 2 36 Size Front 6.50-10 10PR 37 Rear 5.00-8 - 8PR 38 Wheelbase mm 1425 39 Tread Front mm 890 920 Rear mm 920 mm 1045 Overhead Guard Clearance mm 1035 Counterweight mm 1110 Drawbar Pin Center mm 495 Step / Floor mm 420 / 650 40 Underclearance Min. with load mm 100 41 Center of Wheelbase mm 110 42 Brake Service (Foot) Hydraulic - Foot pedal 43 Parking Mechanical - Hand lever 45 Battery Voltage / Capacity (5HR) V/AH 12 / 52 49 Internal Combustion Engine Make/ KUBOTA D1503 Rated Horsepower / r.p.m. kw 21.3 / 2500 Rated Torque / r.p.m. N m 98 / 1600 51 Number of Cylinder 3 52 Piston Displacement cc 1499 Alternator output kw/amp 0.54 / 45 Fuel Tank Capacity Type lit 50 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd.-Rvs 2-2 1-1 2-2 1-1 57 Operating Pressure For Attachments MPa (psi) 17.7 *Computed values

Characteristics Dimensions Performance Weight Chassis Engine and Transmission I Manufacturer TCM 2 FHG15C3 FHG15T3 FHG18C3 FHG18T3 3 Load Capacity kg 1500 1750 4 Load Center mm 500 5 Power Type Diesel 6 Operation Position Seated 7 Tire Type Front / Rear Pneumatic 8 Wheels (X=driven) Front / Rear 2X / 2 9 Maximum mm 3000 10 Free Lift mm 155 13 Size L x W x T mm 920 x 100 x 35 Spread (Outside) / Min. mm 920 / 200 14 Tilt Fwd / Bwd deg 6-12 15 Length to Face mm 2245 2275 16 Overall Width mm 1070 1100 17 Lowered mm 1995 18 Raised mm 4030 19 Overhead Guard (EXB, EXK) mm 2070 Overhead Guard (EXC, EXE, EXN) mm 2130 20 Operator s Seat mm 1045 21 Turning Radius (Outside) mm 1980 2010 22 Load Distance mm 395 (Centerline of front axle to front face of forks) Rear Overhang mm 425 455 23 Basic Right Stacking Aisle Width mm 3685 3715 (Add load length and clearance) 24 Speeds Travel Full load km/h 18.5 / 18.5 19.0 / 19.0 18.5 / 18.5 19.0 / 19.0 (Fwd/Rvs.) No load km/h 19.0 / 19.0 19.5 / 19.5 19.0 / 19.0 19.5 / 19.5 25 Lifting Full load mm/s 620 No load mm/s 680 26 Lowering Full load mm/s 450 No load mm/s 550 28 Drawbar Pull Full load kn 14.7 18.6 14.7 18.6 No load kn 6.9 30 Gradeability* Full load % 25 33 22 31 No load % 18 17 32 Total Weight kg 2620 2780 33 Weight Distribution Full load Front kg 3550 3910 Rear kg 570 620 34 No load Front kg 1110 1060 Rear kg 1510 1720 35 Tires Number Front / Rear 2 / 2 36 Size Front 6.50-10 10PR 37 Rear 5.00-8 - 8PR 38 Wheelbase mm 1425 39 Tread Front mm 890 920 Rear mm 920 mm 1045 Overhead Guard Clearance mm 1005 Counterweight mm 1110 Drawbar Pin Center mm 495 Step / Floor mm 420 / 650 40 Underclearance Min. with load mm 100 41 Center of Wheelbase mm 110 42 Brake Service (Foot) Hydraulic - Foot pedal 43 Parking Mechanical - Hand lever 45 Battery Voltage / Capacity (5HR) V/AH 12 / 64 49 Internal Combustion Engine Make/ NISSAN DIESEL TD27 - II Rated Horsepower / r.p.m. kw 42.0 / 2400 Rated Torque / r.p.m. N m 170 / 2300 51 Number of Cylinder 4 52 Piston Displacement cc 2663 Alternator output kw/amp 0.72 / 60 Fuel Tank Capacity Type lit 50 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd.-Rvs 2-2 1-1 2-2 1-1 57 Operating Pressure For Attachments MPa (psi) 17.7 *Computed values

STANDARD SPECIFICATIONS Diesel -- 2-2,5-3 - 3,5 ton Engine & Transmission Chassis & Wheels Weight Performance Dimensions Characteristics 1 Manufacturer TCM 2 FD20C3 FD20T3 FD25C3 FD25T3 3 Load Capacity kg 2000 2500 Load Center mm 500 500 5 Power type Diesel Diesel 6 Operator Position Seated Seated 7 Tire Type Front / Rear Pneumatic Pneumatic 8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 9 Maximum mm 3000 3000 10 Free Lift mm 105 110 13 Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40 Spread (Outside) / Min. mm 1020 / 245 1020 / 245 14 Tilt Fwd / Bwd deg 6 / 12 6 / 12 15 Lenght to Face mm 2485 2555 16 Overall Width mm 1150 1150 17 Lowered mm 2030 2030 18 Raised mm 4030 4030 19 Overhead Guard (EXB, EXK) mm 2070 2070 Overhead Guard (EXC, EXE, EXN) mm 2130 2130 20 Operator s Seat mm 1045 1045 21 Turning Radius (Outside) mm 2170 2240 22 Load Distance (Centerline of Axle to Front Face of s) mm 450 450 Rear Overhang mm 435 505 23 Basic Right Stacking Aisle Width (Add load length and clearance)) mm 3925 3995 24 25 Speeds Lifting 26 Lowering 28 Drawbar Pull 29 Gradeability* Travel (Fwd. / Rvs.) Full Load km/h 18,5 18 18,5 18 No Load km/h 19 18,5 19 18,5 Full Load mm/s 630 630 No Load mm/s 670 670 Full Load mm/s 450 450 No Load mm/s 550 550 Full Load kn 13,7 19,1 13,7 19,1 No Load kn 8,3 8,3 Full Load % 23 34 20 28 No Load % 20 20 32 Total Weight kg 3340 3700 Front kg 4670 5400 33 Full Load Rear kg 670 800 Weight Distribution Front kg 1490 1420 34 No Load Rear kg 1850 2280 35 Number Front / Rear 2 / 2 2 / 2 36 Tires Front 7,00-12 - 12PR (l) 7,00-12 - 12PR (l) Size 37 Rear 6,00-9 - 10PR (l) 6,00-9 - 10PR (l) 38 Wheelbase mm 1600 1600 39 Tread Front mm 970 970 Rear mm 970 970 mm 1040 1040 Overhead Guard Clearance mm 1005 1005 Counterweight mm 1110 1110 Drawbar Pin Center mm 530 530 Step / Floor mm 435 / 650 435 / 650 40 Minimum Full Load mm 110 110 Underclearance 41 Center of wheelbase mm 120 120 42 Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Brake 43 Parking Mechanical-Hand lever Mechanical-Hand lever 45 Battery Voltage / Capacity (5HR) V / AH 12 / 64 12 / 64 49 Make - NISSAN DIESEL / TD27-II NISSAN DIESEL / TD27-II 50 Rated Horsepower / r.p.m. kw 42,0 / 2400 42,0 / 2400 51 Rated Torque / r.p.m. N-m 170 / 2300 170 / 2300 Internal Combustion Engine Number of Cylinder 4 4 52 Piston Displacement cc 2663 2663 Alternator output kw/amp 0,72 / 60 0,72 / 60 Fuel Tank Capacity Type liter 70 70 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd - Rvs 2-2 1-1 2-2 1-1 57 Operating Pressure For attachment MPa 17,7 17,7

Engine & Transmission Chassis & Wheels Weight Performance Dimensions Characteristics 1 Manufacturer TCM 2 FD30C3 FD30T3 FD35T3S 3 Load Capacity kg 3000 3500 Load Center mm 500 500 5 Power type Diesel Diesel 6 Operator Position Seated Seated 7 Tire Type Front / Rear Pneumatic Pneumatic 8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 9 Maximum mm 3000 3000 10 Free Lift mm 165 170 13 Size L x W x T mm 1070 x 122 x 45 1070 x 150 x 50 Spread (Outside) / Min. mm 1090 / 250 1090 / 300 14 Tilt Fwd / Bwd deg 6 / 12 6 / 12 15 Lenght to Face mm 2705 2800 16 Overall Width mm 1225 1290 17 Lowered mm 2075 2135 18 Raised mm 4260 4255 19 Overhead Guard (EXB, EXK) mm 2090 2140 Overhead Guard (EXC, EXE, EXN) mm 2150 2200 20 Operator s Seat mm 1070 1120 21 Turning Radius (Outside) mm 2400 2470 22 Load Distance (Centerline of Axle to Front Face of s) mm 480 495 Rear Overhang mm 525 605 23 Basic Right Stacking Aisle Width (Add load length and clearance)) mm 4185 4145 24 25 Speeds Lifting 26 Lowering 28 Drawbar Pull 29 Gradeability* Travel (Fwd. / Rvs.) Full Load km/h 19 19 No Load km/h 19,5 19,5 Full Load mm/s 520 460 No Load mm/s 590 490 Full Load mm/s 450 420 No Load mm/s 450 450 Full Load kn 12,7 17,2 18,1 No Load kn 9,8 10,8 Full Load % 15 21 20 No Load % 20 17 32 Total Weight kg 4390 4940 Front kg 6410 7290 33 Full Load Rear kg 980 800 Weight Distribution Front kg 1680 1420 34 No Load Rear kg 2710 2280 35 Number Front / Rear 2 / 2 2 / 2 36 Tires Front 28 x 9-15 - 12PR (l) 7,00-12 - 12PR (l) Size 37 Rear 6,50-10 - 10PR (l) 6,00-9 - 10PR (l) 38 Wheelbase mm 1700 1600 39 Tread Front mm 970 Rear mm 970 970 mm 1300 1040 Overhead Guard Clearance mm 1005 1005 Counterweight mm 1130 1110 Drawbar Pin Center mm 560 530 Step / Floor mm 460 / 680 435 / 650 40 Minimum Full Load mm 140 110 Underclearance 41 Center of wheelbase mm 145 120 42 Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Brake 43 Parking Mechanical-Hand lever Mechanical-Hand lever 45 Battery Voltage / Capacity (5HR) V / AH 12 / 64 12 / 64 49 Make - NISSAN DIESEL / TD27-II NISSAN DIESEL / TD27-II 50 Rated Horsepower / r.p.m. kw 42,0 / 2400 42,0 / 2400 51 Rated Torque / r.p.m. N-m 170 / 2300 170 / 2300 Internal Combustion Engine Number of Cylinder 4 4 52 Piston Displacement cc 2663 2663 Alternator output kw/amp 0,72 / 60 0,72 / 60 Fuel Tank Capacity Type liter 70 70 55 Transmission Type Manual Power-shift Manual Stage Fwd - Rvs 2-2 1-1 2-2 57 Operating Pressure For attachment MPa 17,7 17,7

Engine & Transmission Chassis & Wheels Weight Performance Dimensions Characteristics 1 Manufacturer TCM 2 FHD20C3 FHD20T3 FHD25C3 FHD25T3 FHD30C3 FHD30T3 3 Load Capacity kg 2000 2500 3000 Load Center mm 500 500 500 5 Power type Diesel Diesel Diesel 6 Operator Position Seated Seated Seated 7 Tire Type Front / Rear Pneumatic Pneumatic Pneumatic 8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 2x / 2 9 Maximum mm 3000 3000 3000 10 Free Lift mm 105 110 165 13 Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40 1070 x 125 x 45 Spread (Outside) / Min. mm 1020 / 245 1020 / 245 1090 / 250 14 Tilt Fwd / Bwd deg 6 / 12 6 / 12 6 / 12 15 Lenght to Face mm 2485 2555 2705 16 Overall Width mm 1150 1150 1225 17 Lowered mm 2030 2030 2075 18 Raised mm 4030 4030 4260 19 Overhead Guard (EXB, EXK) mm 2070 2070 2090 Overhead Guard (EXC, EXE, EXN) mm 2130 2130 2150 20 Operator s Seat mm 1045 1045 1070 21 Turning Radius (Outside) mm 2170 2240 2400 22 Load Distance (Centerline of Axle to Front Face of s) mm 450 450 480 Rear Overhang mm 435 505 525 23 Basic Right Stacking Aisle Width (Add load length and clearance)) mm 3925 3995 4185 24 25 Speeds Lifting 26 Lowering 28 Drawbar Pull 29 Gradeability* Travel (Fwd. / Rvs.) Full Load km/h 18 18 19 No Load km/h 18,5 18,5 19,5 Full Load mm/s 620 620 520 No Load mm/s 640 640 540 Full Load mm/s 450 450 450 No Load mm/s 550 550 450 Full Load kn 15,7 26,5 15,7 26,5 14,8 13,5 No Load kn 8,3 8,3 9,8 Full Load % 28 38 24 32 16 27 No Load % 20 18 20 32 Total Weight kg 3340 3700 4390 Front kg 4680 5400 6410 33 Full Load Rear kg 660 800 980 Weight Distribution Front kg 1500 1420 1690 34 No Load Rear kg 1840 2280 2700 35 Number Front / Rear 2 / 2 2 / 2 2 / 2 36 Tires Front 7,00-12 - 12PR (l) 7,00-12 - 12PR (l) 28 x 9-15 - 12PR (l) Size 37 Rear 6,00-9 - 10PR (l) 6,00-9 - 10PR (l) 6,50-10 - 10PR (l) 38 Wheelbase mm 1600 1600 1700 39 Tread Front mm 970 970 Rear mm 970 970 970 mm 1040 1040 1300 Overhead Guard Clearance mm 1005 1005 1005 Counterweight mm 1110 1110 1130 Drawbar Pin Center mm 530 530 560 Step / Floor mm 435 / 650 435 / 650 460 / 680 40 Underclearance Minimum Full Load mm 110 110 140 41 Center of wheelbase mm 120 120 145 42 Brake Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal 43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever 45 Battery Voltage / Capacity (5HR) V / AH 12 / 64 12 / 64 12 / 64 49 Make - KUBOTA / V3300 KUBOTA / V3300 KUBOTA / V3300 50 Rated Horsepower / r.p.m. kw 50 / 2500 50 / 2500 50 / 2500 51 Rated Torque / r.p.m. N-m 226,4 / 1800 226,4 / 1800 226,4 / 1800 Internal Combustion Engine Number of Cylinder 4 4 4 52 Piston Displacement cc 3318 3318 3318 Alternator output kw/amp 0,54 / 45 0,54 / 45 0,54 / 45 Fuel Tank Capacity Type liter 70 70 70 55 Transmission Type Manual Power-shift Manual Power-shift Manual Power-shift Stage Fwd - Rvs 2-2 1-1 2-2 1-1 2-2 1-1 57 Operating Pressure For attachment MPa 17,7 17,7 17,7

CAPACITY / LOADCENTER The products manufactures at TCM plant got ISO 9001 & 14001 certificates