# 856A1300G LENGTH GAGE-CORE MODULE

Tool No. S/N Description Remarks Dept. ATA # 856A1009G02 12883 Adapter, vertical lift CFM56 132 72-41-00 # 856A1015G01 12886 Sling frames, 3 legs CFM56 132 72-55-00 # 856A1020G08 12844 Restraining core module CFM56 132 72-00-00 # 856A1021G02 12888 Fixture lift/turn comp CFM56 132 72-31-00 # 856A1042G08 12968 Wrench torque #4 brg. ret CFM56 132 72-00-02 # 856A1057G03 12903 Fixture lift/turn HPT CFM56 132 72-00-52 # 856A1061G03 12964 Fixt. lift/turn HPTR disk CFM56 132 72-00-52 # 856A1073G03 20000 Truck HPTR Horizontal Transport and store HPT rotor 132 72-52-00 # 856A1083G02 12904 Fixture lift/turn core CFM56 132 72-00-02 # 856A1102G03 12905 Fixture horizontal lift CFM56 132 72-00-51 # 856A1103G01 12906 Fixture lift HPT nozzle CFM56 132 72-00-51 # 856A1107G07 12908 Fixture lift core module CFM56 132 72-00-02 # 856A1125G01 12910 Fixture lift horizontal CFM56 132 72-00-02 # 856A1157G02 12972 Fix. lift Adj. CF CFM56 132 72-00-01 # 856A1196G02 12913 Fixture lift/turn comb. CFM56 132 72-41-00 # 856A1300G02 20079 LENGTH GAGE-CORE MODULE TO MEASURE OVERALL LENGTH OF CORE MODULE PRIOR TO INSTALL 132 72-00-02 # 856A1313G04 12919 Ring support eng. handlin CFM56 132 72-00-01 # 856A1314G01 12920 Bracket set LPT aft mount CFM56 132 72-00-00 # 856A1332G01 12921 Fixt. lift/turn core fwd. CFM56 132 72-00-02 # 856A1335G01 12922 Bracket set HPC CFM56 132 72-00-32 # 856A1354G02 12923 Bracket set handling core CFM56 132 72-00-02 # 856A1377G01 12976 Fixt. lift/turn HPTS/LPT CFM56 132 72-53-00 # 856A1421G01 12927 Fixture lift top case HPC CFM56 132 72-00-32 # 856A2543G02 12843 LPT Shaft Centering Fixt. CFM 56 132 72-00-00 # 856A2549G01 20039 TURB.FRME HANDLG. SEGMENT TO HANDLE THE TURBINE FRAME 132 72-56-00 # 856A2627G05 20028 LIFTING BEAM LIFT LPT MAJOR MODULE, 1-2 BOOSTER SPOOL, FAN DISK,LPT CASE 132 72-00-03 # 856A2645G04 12934 Beam CG engine handling CFM56 132 72-00-00 # 856A2646G01 12847 Turbine frame Dolly CFM56 132 72-00-00 # 856A3111G05 12852 Dolly Trunion Fan Frame module 132 72-00-00 # 856A3373G01 20040 LPT BLADED DISK FIXTURE TO HANDLE THE LPT STAGE 1-4 DISK AND BLADES. 132 72-54-00 # 856A3387G03 20032 LPT LIFT & TURN FIXT. TO TURN THE LPT CASE 180 DEGREES 132 72-54-00 # 856A3503G01 12900 Fixt. booster rotor assy. CFM56 132 72-21-00 # 856A3510G03 20041 ADAPTER, 1-2 SUPPORT TO SUPPORT, LIFT AND TURN 1 AND 2 BRG SUPPORT 132 72-22-00 # 856A3532G01 20034 FIXT. LIFT & TURN FAN FRM TO PERMIT LIFTING AND TURNING OF FAN FRAME MODULE 132 72-23-00 # 856A3533G01 20035 FAN INLET 3 LEG SLING TO HANDLE FAN INLET CASE OR FAN FRAME ASSEMBLY. 132 72-23-00 # 856A3538G01 20043 FIXTURE, HNDLNG FAN DISK TO HANDLE THE FAN DISK WITH TWO YOKES AND A STRAP. 132 72-21-00 # 856A3540G01 20044 FIXT.HNDLNG/TURN BSTR SPL TO LIFT AND HANDLE THE BOOSTER SPOOL 132 72-21-00 # 856A3596G02 20038 LIFTING BEAM, FAN FRAME TO HANDLE THE FAN MAJOR MODULE 132 72-00-01

# 856A3767G01 20072 FIXT. HNDLNG LPT RTR/STTR TO LIFT AND TURN THE LPT MODULE 132 72-54-00 # 856ATT2360 12853 Lifting Eye Fan Frame Assy 132 72-00-00 # 856ATT2360 12854 Lifting Eye Fan Frame 132 72-00-00 #*856A3519G04 20033 AGB - 3-LEG SLING TO HANDLW AGB OR AGB EQUIPPED WITH FUEL PUMP & MEC. 132 72-00-63 *856A1404P14 AT3532 TOOL, ADAPTER PLATE HPT B Adapter for Tool 856A1404 to HPT rotor front shaft 132 72-52-04 856A1000G08 20027 WRENCH #3 LOCKING NUT TORQUE/LOOSEN & TURN IGB #3 LOCKING NUT DURING ASSY/DISSY 132 72-00-02 856A1001G01 AT3472 WRE KEY TRCH MULTIPLIER DEC EFFORT REQ TO SPPLY INPUT TRQ TO SWEENEY TORQ MULTIPLIER 132 72-00-61 856A1005G01 12880 Wrench, compressor rotor CFM56 132 72-00-31 856A1006G01 12881 Wrench torque adapter CFM56 132 72-00-02 856A1007G04 12966 Support dummy comb case CFM56 132 72-00-02 856A1008G02 12882 Fixture, lift & Turn HPTR CFM56 132 72-00-52 856A1008G03 20332 FIXT.HPTR AFT END To lift and turn HPT and HPC during assy and dissy. 132 72-31-00 856A1010G01 12884 Wrench, rachet comp. roto CFM56 132 72-31-00 856A1012G01 12885 Lever, countertorque comp CFM56 132 72-00-32 856A1013P01 AT3488 VSV HOLDER To apply countertorque to the Comp Stator Vanes from inside 132 72-00-32 856A1016G05 20001 Stand Compressor Rotor To support compressor rotor & HPT rotor in Vert. position. 132 72-31-00 856A1017G03 12887 Puller, Impact-HPT Shroud CFM56 132 72-53-00 856A1017G04 20074 PULLER HPT SHROUD TO REMOVE HPT SHROUD SEGMENTS 132 72-53-00 856A1018G03 AT3483 Stand Subasembly-Frame To support the combustion case during overhaul operations 132 72-41-00 856A1019G04 20135 FIXT.VRTCL LIFT COMB CHMB TO LIFT AND TURN THE COMBUSTION CASE 132 72-41-00 856A1022G03 12889 Wrench set spanner air CFM56 132 72-00-02 856A1023G01 20115 DR NUT STRT COMP RTR 3,4 START NUTS ON BOLTS THAT SECURE STAGE 4-9 SPOOL,STAGE 3 132 72-31-00 856A1025G02 20129 LOCATOR, SEAL WIRE COMP. TO LOCATE AND ESTABLISH THE ENDS OF THE COMPR SEAL WIRE 4-9 132 72-00-02 856A1028G01 20120 LIFT FIXT.CPR STG 1-2 SPL TO LIFT AND TURN THE 1-2 OR 4-9 COMP. SPOOL 132 72-31-00 856A1033G01 12967 Puller #3 brg. gear CF56 132 72-61-00 856A1034G01 12890 Wrench 35-tooth bevel gr. CFM56 132 72-61-00 856A1035G01 12891 Fixture, hold #3 brg. IGB CFM56 132 72-61-00 856A1037G01 12892 Wrench, puller ring IGB CFM56 132 72-61-00 856A1039G01 12893 Adapter IGB to pwr arm CFM56 132 72-61-00 856A1040G01 12894 Removal IGB brg. & Spacer CFM56 132 72-61-00 856A1045G01 12895 Wrench #3 bearing retaine CFM56 132 72-61-00 856A1046G03 12896 Wrench #3 brg rotating se CFM56 132 72-61-00 856A1047G03 12969 Fix. hold IGB module CFM56 132 72-61-00 856A1048G02 12897 Table antitorque IGB Mod. CFM56 132 72-61-00 856A1049G01 12898 Puller #3 bearing inner r CFM56 132 72-61-00 856A1051G02 12901 Puller arm comp. stator CFM56 132 72-00-32 856A1052G05 20277 PRECISION B/U HPTR TO MEASURE THE R/U OF THE HPTR MATING PARTS DURING ASSY. 132 72-52-00

856A1054G02 12902 Tool set inst/rem IGB/#3 CFM56 132 72-61-00 856A1055G01 20260 FIXTURE SET, GRIND SPACER To hold the stator liners in proper position during grinding 132 72-33-00 856A1058G01 20137 COMP. BLADE VIBRATOR TO ASSIST IN THE REMOVAL OF THE STAGE 4-9 BLADES 132 72-31-00 856A1063G02 20181 TOOL SET-COMP STTR& LINER TO INSTALL AND REMOVE COMP. STATOR AND LINERS 132 72-31-00 856A1063G03 20311 TOOL SET-CMPSSR LINER To install and remove the HPC vane sectors and liners. 132 72-32-00 856A1063G07 20160 Tool Set Compressor Stato To install and remove the HPC vane sectors and liners 132 72-32-00 856A1068G02 20203 GAGE LKG LUG COMP ASSY TO INSPECT THE COMPRESSOR BLADE LOCKING SCREWS FOR INSTALL. 132 72-33-00 856A1069G01 AT3485 Bracket,Trunnion CombCase To support the combustion case during the subassembly stand 132 72-41-02 856A1069G04 20142 BRACKET TRUNN.,COMB CASE TO SUPPORT THE COMB CASE DURING OVERHAUL 132 72-41-00 856A1070G02 AT3482 Fixture, Spline Bolt Remv To Install & Remove HPT Inner Nozzle Support attaching bolts 132 72-41-00 856A1071G04 AT3498 Tool set liner vanes To remove stg 6-9 liners and stg 6-8 vane segments 132 72-33-00 856A1072G04 AT3497 Truck HPCR To store and transport the compressor rotor assembly 132 72-31-00 856A1075G02 20182 FIXT-LIFT HPTR DISK USED TO LIFT AND TURN THE HPTR TO THE HPC 132 72-53-00 856A1076G01 20108 Fix, Chilling To hold dry Ice in the Flange of the HPT disk 132 72-52-00 856A1081G05 12845 Core Module Horiz. Stand CFM56 132 72-00-00 856A1082G01 AT3471 FIXT. LIFT HPTR VERTICAL TO LIFT THE HPTR IN THE VERTICAL POSITION TO ACCESS THE HPCR 132 72-00-02 856A1084G04 20116 CART STATOR ACTUATOR POSITION VARIABLE STATOR VANES & VARIABLE BLEED VALVES 132 72-00-02 856A1085G02 12855 Lift Bar Main Engine Section fit with 856A1088 132 72-00-00 856A1086G02 12848 Stand Assy, CORE SECTION VERTICAL ASSY/DISSY CORE SECTION 132 72-00-02 856A1086G02 20048 STAND ASSY-CORE SECTION TO SUPPORT THE CORE ENGINE FOR VERTICAL ASSEMBLY/DISASSEMBLY 132 72-00-02 856A1088G04 AT3477 SUPPORT&ROTATION-CORE ENG TO SUPPORT AND PROVIDE COUTERTORQUE FUNTION TO THE CMPR 132 72-00-02 856A1089G02 12970 Adapter HPTR to compr. CFM56 132 72-00-02 856A1089G04 20136 BRACKET-TRUN. CMB CHMB TO SUPPORT THE COMBUSTION CASE ON THE SUBASSEMBLY STAND 132 72-41-00 856A1090G01 20231 INSTALLER - HPT NOZ SGMT To insert the seal retaining pins in the HPT nozzle. 132 72-00-51 856A1092P01 20204 HOLDING FIXT.HPT SEAL TO HOLD THE HPT AFT SEAL AND SUPPORTS DURING ASSEMBLY 132 72-52-00 856A1093G02 AT3484 Fixture,Lift To remove/install combustion chamber & HPT inner fwd Nz supp 132 72-41-00 856A1093G03 AT3499 LIFT FIXT-COMB CHMBR TO REMOVE/INSTALL COMB. CHAMBER AND THE HPT NOZZLE SUPPORT 132 72-41-00 856A1094G01 20002 Adapter Holding To position the HPT nozzle vertically and enable to rotate. 132 72-51-00

856A1095G04 12899 Fixture HPT nozzle assy. CFM56 132 72-00-51 856A1099G01 AT3467 FIXT-INSTL-REMVL HPT AFT TO INSTALL AND REMOVE THE HPT AFT SHAFT 132 72-52-00 856A1100G01 20232 DRIVER, RTNR PIN HPT NZLE To install the HPT Nozzle outer support retaining pins 132 72-00-51 856A1106G02 12907 Pin set, guide core CFM56 132 72-00-02 856A1114G01 AT3491 Brkt Support Manifold Support the fuel manifold on combustion case during assembly 132 72-41-00 856A1117G02 AT3487 Fixture, Lift HPTR, HORIZ To provide an interface b/w HPTR assy the general lift fixtu 132 72-00-52 856A1123G01 12909 Guide fan frame/core CFM56 132 72-00-02 856A1126G02 20233 DRIVER-GUIDE STRIPS CMPSR To install the forward &Aft guide sectors in the CMPSR 132 72-30-00 856A1126G04 20234 DRIVER-GUIDE STRIPS CMPSR To install the forward &Aft guide sectors in the CMPSR 132 72-30-00 856A1127P01 20151 Protector HPT Shroud LPT To support the HPT stator shroud & protect fwd flange bolts 132 72-53-00 856A1130G07 Tool set jackscrew CFM56 132 72-00-00 856A1130G09 Tool set jackscrew CFM56 132 72-00-00 856A1130G10 Tool set jackscrew CFM56 132 72-00-00 856A1132G01 20235 FIXTURE, RESTRAIN-HPT RTR To hold the HPT blades radially outwrd durg blade grinding 132 72-00-52 856A1133P02 12971 Tool rmv bld rtnr aft CFM56 132 72-00-52 856A1136G02 AT3494 ADPT,NO.4 BRG Adapt No.4 BRG retainer wrench and core module 132 72-00-52 856A1140G06 12911 Fixture support core mod. CFM56 132 72-00-02 856A1145P02 AT3490 Fix,Inst. Outer Air Duct To Install the Air Duct in to the LPT support & Nozzle Sgmt 132 72-53-00 856A1145P03 20102 FIXTURE INSTALL OUTR COOL TO INSTALL THE AIR DUCT TO THE LPT SUPPORT AND NOZZLE SEGMT 132 72-54-00 856A1146P02 20103 FIXT. INSTL INNER DUCT TO INSTALL THE INNER DUCT TO THE LPT NOZZLE ASSY 132 72-53-00 856A1147G01 20279 TOOL-RADIAL POSITION To set the proper radial position of 5TH STG MANIFOLD 132 72-00-02 856A1154P02 20134 SETUP MASTER CMPR BUILDUP TO SETUP THE ROTARY TABLE & CHUCK USED FOR COMPR BUILDUP 132 72-00-02 856A1172G01 12912 wrench set #3 brg. CFM56 132 72-00-01 856A1195G02 AT3486 Fixture Assy HPC Sgt 1&2 To support the compressor rotor fwd shaft assy sty 1&2 spool 132 72-31-00 856A1198G01 12914 Pullar aft shaft CFM56 132 72-52-00 856A1204G01 12973 Fixt. remove HPCR spool CFM56 132 72-31-00 856A1206G04 20138 CDP SEAL GAGE RUNOUT TO PROVIDE FIR OF THE CDP SEAL TO DETERMINE IF SEATED 132 72-31-00 856A1211G01 20147 Fix Clamping #3 Brg Assy To eliminate movement in the IGB provide measuring surface 132 72-00-02 856A1216G02 12974 Pull. #4 brg. Otr. race CFM56 132 72-00-52 856A1219G02 20145 HEATER-HPT AFT SHAFT 132 72-00-52 856A1219G02 AT3537 Heater,HPT AFT Shaft To heat the HPT aft shaft prior to No. 4 bearing outer race 132 72-52-00

856A1220G03 12915 Tool set inst/rem HPT CFM56 132 72-52-02 856A1225G01 20078 HPTR BUILD FIXTURE BASE FIXTURE USED TO BUILD HPTR & RUNOUT TOOL 132 72-52-00 856A1241P02 20130 DESICCANT DRYER TO SUPPLY FILTERED AIR TO THE HIGH COMPRESSOR 132 72-31-00 856A1265G08 20133 HEATER BEVEL GEAR IGB TO HEAT THE IGB BEVEL GEAR BORE PRIOR TO INSTALLATION 132 72-61-00 856A1266G03 20186 COMP CASE ALIGNMENT PIN TO PROVIDE CORRECT ALIGNMENT OF CASES DURING ASSEMBLY 132 72-00-02 856A1281G02 AT3492 Fixt Lift HPT Vertically lift front outer sealon and off the STG1 HPT Disk 132 72-52-00 856A1284G01 12916 Puller pin HPT nozzle CFM56 132 72-00-51 856A1290G01 20205 FIXT. RUNOUT CORE MOD. TO CHECK THE RUNOUT ON THE CORE ON THE 1088 FIXTURE 132 72-00-02 856A1293G01 12917 Retainer set comb. inner CFM56 132 72-00-51 856A1295G02 20206 FIXT. ALIGN CDP SHIELD TO PROVIDE ALIGNMENT TO THE CDP EROSION SHIELD DURING INSTAL 132 72-31-00 856A1299G02 12918 Fixture blade removal CFM56 132 72-00-52 856A1308G01 12975 Puller HPTR Fwd Out. Seal CFM56 132 72-52-00 856A1334G04 20111 FIXT BLDUP CORE EN HP COM FIXT SUPPS CORE MAJ MOD MAINTAINS MOST AFT STACK POSITION 132 72-31-00 856A1342G01 20207 FIXT. PRESEAT VSV ARM FIXT. IS USED TO PRESEAT THE VSV LEVER ARMS DURING ASSEMBLY 132 72-00-32 856A1344G02 20114 FXT SETUP CRE ENG/HP COMP SETUP FIXT USED TO SETUP/CHECK CORE ENGINE HP COMP ROTOR BLD 132 72-00-02 856A1356G02 20140 LIFT TOOL COMPR STG 1-2 LIFT FIXTURE TO BE USED TO LIFT & TURN THE STG 1-2 SPOOL 132 72-21-00 856A1358G01 AT3496 Fix Ins/Rem MOD 12 Fixture to installed and remove the MOD 12 132 72-00-02 856A1360G01 20104 TOOL SET RUNOUT-HPT SHROU RUNOUT TOOL TO GET MEASUREMENTS OF COMP CASE 132 72-00-02 856A1363G01 12924 Guise assy fan/core mod. CFM56 132 72-00-02 856A1369G03 20126 FIXT. ADAPTR-LINIGAGE THE ADAPTER COMMUNICATES HPC & HPT ANGULAR DATA 132 72-00-02 856A1371G01 20121 CART,COMPUTER LINI GAGE TO PROVIDE STORAGE,TRANSP, AND BENCH FOR 856A1360 &1369 132 72-00-02 856A1372G01 20208 GAGE - ARM BOW USED TO MEASURE THE HPT OUTER SEAL 132 72-00-52 856A1375G01 20158 Fix. Core-Turning To manually turn the core during CDP bore runout 132 72-00-02 856A1378G01 20082 BOLT RETAINER SET TO PREVENT THE BOLTS FROM MOVING DURING INSTALL HPTR TO HPC 132 72-00-52 856A1380G01 12925 Puller outer ducts LPT CFM56 132 72-53-00 856A1381G01 20105 PULLER OUTER AIR DUCTS TO REMOVE AIR DUCTS FROM HPT/LPT OUTER AIR DUCTS 132 72-00-02 856A1382G01 AT3520 STUD PROTECTOR,HPT SHROUD To protect the forward flange slabbed-head bolts DURING ASSY 132 72-53-00 856A1384G01 12926 Tool Rem. HPT shroud clip CFM56 132 72-53-00 856A1386G04 20059 LIFT FIXTURE-CORE 132 72-00-02

856A1388G01 20241 GUAGE, SEATING CHECK To check seating between core module and IGB 132 72-00-61 856A1389G01 AT3493 Fix Install No.4 BRG To install No.4 BRG outer race into the HPT rear shaft 132 72-00-52 856A1394G01 20180 FIXTURE LIFT 132 72-00-03 856A1403G02 20236 PROTECTOR SET HPT NZL To protect the FWD & AFT ends of HPT NZL VNS DRG STRG 132 72-51-00 856A1404G01 20110 FIXT PREC BLDUP/RUNOUT TO MEAS RUNOUT OF HP TRBN ROTORS MATING PRTS/ASSBLY HP TURB 132 72-52-00 856A1409G02 20071 FIXT,TORQUE HPTR FRT SHFT BTO BREAK AWAY TORQUE ON HPTR FWD SHFT AND AIRSEAL 132 72-54-00 856A1411G04 20117 PUSH/PULL FIXT. HPTR TO INSTALL/REMOVE THE HPT BLADE RETAINER. 132 72-53-00 856A1416G03 20106 FIXT. BUILDUP LPT STG 1 TO BUILDUP LPT STG 1 NOZZ. BY HOLDING THE 24 VANES TOGETHER 132 72-53-00 856A1417G04 20322 FIXTURE LIFT AND TURN HPT To lift and turn the HPTR during engine buildup 132 72-52-00 856A1423G05 AT3474 CORE MOD. RESTRAIN FIXT. TO RESTRAIN THE HPT ROTOR DURING INSTALL/REMOVAL. 132 72-00-02 856A1424G04 20276 FIXT.-LIFT COMB ASSY TO LIFT THE COMBUSTORS VERICALLY AND HORIZONTALLY 132 72-41-00 856A1431G03 AT3463 FIXT, RESTRAIN HPT NOZZLE TO RESTRAIN NOZZLE SEGMENTS OF HPT NOZZLE CIRCUMFERENTIALLY 132 72-41-00 856A1433G02 AT3468 TORQUE TOOL HPT STATOR TORQUE TOOL USED TO INSTALL/REMOVE HPT STATOR BUSHING 132 72-00-53 856A1448G01 20127 FIXT. LOCATOR-HEAT SHIELD TO ORIENT & SPACE THE HEAT SHIELD SEGMENTS TO THE SHROUD SUP 132 72-00-52 856A1449G03 20089 FIXTURE-GRNDG HPT SHROUD TO GRIND THE HPT SHROUDS AS AN ASSEMBLY DURING ASSEMBLY 132 72-52-00 856A1452G02 20090 FIXTURE SUPPORT HPT ROTOR TO SUPPORT THE HPT ROTOR 132 72-52-00 856A1453G01 20081 SANCHION-HPTR TO SUPPORT THE HPTR WHEN ENGINE IS VERTICAL 132 72-00-53 856A1454G01 20091 EXTENSION SHAFT-HPTR TO EXTEND THE HPTR IN ORDER TO SUPPORT THE ROTOR 132 72-52-00 856A1456G02 20237 TOOL SET, REMOVAL HPT BLD To remove blade dampers and assist in pulling HP blades 132 72-52-00 856A1467G01 20209 ADAPTER FUEL MANIFOLD TO PRESSURE CHECK THE FUEL MANIFOLDS DURING ASSEMBLY 132 72-00-02 856A1471G02 20300 BRACKET-LPT FWD FLANGE To provide support for the engine at the forward and AFT END 132 72-54-00 856A1479G01 20238 PULLER, SEAL HPT AFTSEAL To remove the HPT AFT Rotating Seal 132 72-52-00 856A1481G02 20230 VSV Protractor To Measure the VSV angles 132 72-00-02 856A1490G04 20092 FIXTURE INSTL/RMVL MOD 12 TO INSTALL/REMOVE MODULE 12 AND HAVE CONCTY W/ HPT REAR SHFT 132 72-53-00 856A1491G02 20093 BRACKET SET COMP FLNG TO PROVIDE ATTCHMENT POINTS AT THE FOWARD END OF THE CORE 132 72-00-02 856A1602G01 20094 CHILL FIXTURE HPTR BLADE TO HOLD DRY ICE DURING DISSY OF HPT BLADE RETAINER 132 72-52-00 856A1603G04 20335 FIXT,REM HPT AIR SEAL The fixture used to remove/install HPT airseal PST 72-0643 132 72-52-00

856A1603G05 20316 FIXT.INSTL/REM HPT SEAL FIXT TO REMOVE AND INSTALL HPT OUTER SEAL PST 72-0643 132 72-52-00 856A1604G02 20060 FIXTURE,RMVL-BOLT INNER TO REMOVE/INSTALL THE SPLINE DRIVE BOLTS 132 72-41-00 856A1607G01 AT3461 FIXT, LFT-COMB CHAMB/HPT TO LIFT COMB. CHAMBER IN HORIZONTAL & VERTICAL POSITION 132 72-42-00 856A1800G02 20057 BRACKET SET-TRF FWD FLNGE TO SUPPORT TRF FWD FLNGE DURING MAINTENANCE AND STORAGE 132 72-56-00 856A1801G02 20058 RING SUPPORT ENG HNDLG TO SUPORT THE ENGINE AT THE FWD FAN STATOR FLANGE 132 72-00-01 856A1802G02 20113 FXT DUMMY FRWD HPT STATOR PERM INSTALLATION OF AFT CORE MODULE 132 72-00-02 856A1802G02 AT3470 DUMMY FIXTURE MOD 12 TO DUMMY UP MOD 12 DURING LIFT AND TURN PROCEDURE 132 72-00-53 856A1803G01 20128 GUIDE PINS GUIDE PINS TO INSTALL THE CORE TO THE BOOSTER 132 72-00-02 856A1804G01 20061 CORE FIXTURE LIFT AND TURN FIXTURE FOR THE CORE MODULE 132 72-00-02 856A1805G01 20146 Guide-Fan Frame Core Mod 132 72-00-02 856A1807G02 20239 FIXTURE,LIFT HPT STG1 NZL To lift the HPT STG1 NZL ASSY, & CMBSTN ASSY VERT/HZTL 132 72-51-00 856A1812G02 20112 FXT ASSLY/DIS HP TUR NOZZ ASSBLE/DISASSBLE STAGE 1 NOZZLE ASSEMBLY 132 72-51-00 856A1816G01 20210 BRACKET SET HPC CASE TO SUPPORT THE LOWER AHALVE OF THE HPC CASE DURING TOP CASE 132 72-00-02 856A1817G01 20062 TOOL SET RETAINER BOLT TGO INSTALL OR REMOVE THE DOUBLE HEX HEAD RETAINER BOLT 132 72-51-00 856A1818G01 20139 GAGE SEATING CHK CORE/IGB TO MAKE SURE THE FORWARD SHAFT OF HPC IS SEATED IN IGB NO. 3 132 72-00-02 856A1826G01 20195 FIXT. INSTALL/REMOVE #3 PULLER USED TO INSTALL AND REMOVE THE #3 AIRSEAL 132 72-00-01 856A1828G02 20118 TORQUE FIXT. NO.4 BRG TO REMOVE THE NO.4 BRG RETAINER NUT 132 72-00-52 856A1830G01 20148 Guide Assy To guide core during installation 132 72-00-02 856A1832G01 20240 FIXTURE, LIFT/ROTATE CORE This tool works W/856A1423 to lift&turn the core UP,AFT&FWD 132 72-00-02 856A1833G01 20095 FIXT. INSTL RESTRNG CLIP TO INSTALL HPT SHROUD RESTRAINING CLIPS WITH EVEN FORCE 132 72-52-00 856A1838G01 20333 Fixt.Puller HPT Fwd SHAFT TO PULL OFF THE HPT AIRRSEAL FROM THE HPT DISK PST 72-0643 132 72-52-00 856A1839G01 20334 Fixture, Disassy-HPTR/HPC DISSY FIXTURE HPT PST 72-0643 132 72-52-00 856A2004G02 20132 TOOL ASSY,INST/REM HPTR TO INSTALL/REMOVE HPTR TO HPC BOLTS 132 72-52-00 856A2005G01 20003 Guide - Core to Fan Modul Guide Core onto the Fan Module during Assy & Dissy 132 72-00-02 856A2010G01 12928 Fixt. rem. HPT fwd shaft CFM56 132 72-00-52 856A2308G02 20306 SLEEVE,CNTRG REM/INST LPT To center and remove/install the LPT Major to the Fan Major. 132 72-00-03 856A2310G02 20317 FIXT.ALIGN BSTR 2 LPT SFT To align and guide respectively the booster and LPT SHAFT 132 72-00-01 856A2310G02 20319 FIXT.ALIGN- BSTR TO LPT To align and guide respectively the booster and LPT shaft 132 72-00-01

856A2316G01 20080 WRENCH-TORQUE LPT NUT TO TORQUE/LOOSEN LPT COUPLING NUT 132 72-00-03 856A2335G02 20330 STOOL-ASSY/DISSY 1-2 BRG STAND USED TO DISSY/ASSY THE 1-2 BRG SUPPORT 132 72-22-00 856A2336G02 20242 PULLER-FWD RTATNG AIR/OIL To remove the forward rotating air/oil separator. 132 72-00-03 856A2337G01 20243 PULLER-NO.1 INR RACE To remove No.2 inr race halves of No.1 ball BRG 132 72-22-00 856A2339G01 20212 PULLER #1 BRG SLEEVE TO REMOVE THE NO. 1 BRG SLEEVE 132 72-22-00 856A2342G01 20266 TOOL SET,PUSHERS AND ROD INSTLL:N1BRG SLEEVE,INNR/OUTR RACE, OIL BAFFL,AIR/OILSEP 132 72-22-00 856A2345G01 20274 RING-LIFT FAN SHAFT TO LIFT AND HANDLE THE FAN SHAFT 132 72-00-23 856A2373G01 20320 FIXTURE, TORQUE CVT NUT To torque or loosen the Center Vent Tube in the LPT Shaft 132 72-55-00 TO REMOVE THE NO 5 INNER RACE FROM THE LPT 856A2374G01 20190 PULLER-NO 5 BRG INNER SHAFT 132 72-00-03 856A2380G02 20327 FIXT-CHECK CNTR VENT TUBE To control the OD & tightening of the LPT center Vent Tube 132 72-55-00 856A2397G01 20301 CHKG TOOL-CNTR VENT TUBE To control the axial position and runout of the ctr vnt tube 132 72-00-03 856A2412G01 20329 RING,HOLD-STG 1 STAT SEAL To hold the stg 1 outer stationary air seal during transport 132 72-54-00 856A2501G01 20213 WRENCH-VBV MANUAL CONTROL TO MANUALLY CONTROL THE VBV SYSTEM 132 72-00-02 856A2504G01 20169 Push Pull Ferrule Remove/Install flexible shaft ferrules from/on fan fram stru 132 72-23-00 856A2513G04 12929 Tube dummy LPT Shaft CFM56 132 72-00-01 856A2524G01 12846 LPT Module fixture CFM56 132 72-00-00 856A2524G01 AT3504 LPT MAJOR MOD HNDLG FIXT TO HANDLE LPT MAJOR MODULE 132 72-00-03 856A2524G01 AT3505 LPT MAJOR MOD HNDLG FIXT TO HANDLE THE LPT MAJOR MODULE 132 72-00-03 856A2528G01 12849 Stand, Storage LPT Mod. CFM56 132 72-00-00 856A2528G01 AT3502 LPT TRANSPORT STAND TO STORE AND TRANSPORT LPT MAJOR MODULE 132 72-00-03 856A2528G01 AT3503 LPT TRANSPORT STAND TO STORE AND TRANSPORT LPT MAJOR MODULE 132 72-00-03 856A2540G04 20143 LPT SHFT TO MOD. BUILDUP TO ASSY/DISSY THE LPT ASSY MODULES 132 72-54-00 856A2542G02 AT3475 FIXT.-HOIST-LPT MODULE TO HANDLE THE LPT ROTOR/STATOR 132 72-54-00 856A2544G02 20083 TRF DOLLY TRUNNION TO ASSEMBLE/DISASSEMBLE AND STORE THE TRF 132 72-56-00 856A2567G01 20004 LPT Lifting Eye, Forward To handle LPT shaft or LPT major module 132 72-00-03 856A2568G01 20005 LPT Lifting Eye, AFT To handle LPT shaft 132 72-00-03 856A2571G02 12977 Pins guide #1 & #2 Brg. CFM56 132 72-00-01 856A2573G01 12930 Adapt pull LPT Shaft plug To remove LPT shaft plug 132 72-00-03 856A2573G01 AT3535 ADAPTER, PULL - LPT SHAFT To remove LPT shaft plug 132 72-00-03 856A2575G02 12851 Stand Storage LPT LPT 132 72-00-00 856A2576G01 20253 SPACERS,SPPT-LPT RTR/CASE To maintain LPT rotor centered in LPT case 132 72-54-00 856A2577G01 AT3452 ring location #5 brg role jet cell 132 856A2600G05 AT3450 LPT SFT GUIDE/STOP TOOL STOP MAJOR MOD III DUR INSTALLATION ON ENGINE GUIDE LPT SHFT 132 72-00-03 856A2600G05 AT3538 LPT Shaft Guide & Stop TL To stop major module III during installation on engine 132 72-54-00 856A2604G01 12931 Puller aft rot. air/oil CFM56 132 72-00-03 856A2609G01 12932 Block jacking fuel/mec CFM56 132 72-00-63 856A2611G01 12933 Puller LPT CFM56 132 72-00-03

856A2616G01 20267 SECTOR, CENTERING To center LPT shaft relative to fan frame drng MOD2 INST/RMV 132 72-22-00 856A2618G03 20006 Fixture, Rotor/Stator To restrain LPT rotor in relation to LPT stator. 132 72-00-03 856A2618G03 AT3525 FIXTURE, HOLDING -LPTR To restrain LPT rotor in relation to LPT stator 132 72-00-03 856A2618G03 AT3526 FIXTURE, HOLDING -LPTR To restrain LPT rotor in relation to LPT stator 132 72-00-03 856A2625G01 AT3473 FAN & BSTR STORAGE STAND TO STORE FAN AND BOOSTER MODULE 1 132 72-23-00 856A2626G01 AT3495 Stand Storage No.1 & No.2 To store No.1 & No.2 Brg Support module 132 72-22-00 856A2632G01 20155 Puller Remove engine parts which have thread (250-28UNJF-3B) extrac 132 72-00-03 856A2634G01 20052 DLLY STRG ASSY/DIS LPT SH TO STORE ASSEMBLY/DISASSEMBLY LPT SHAFT MODULE 132 72-55-00 856A2640G01 AT3501 TOOL SET OIL RNG SEPARATE To maintain ducts on oil ring separator during DISSY/ASSY 132 72-22-00 856A2642G01 20156 Ring, Restraining No.5 Br To maintain pins during No.5 bumper bearing installation 132 72-00-03 856A2644G03 20049 TOOL, HOLDING-FAN DISK TO TAKE THE RESIDUAL TORQUE FROM FAN SHAFT TO DISK 132 72-00-01 856A2647G02 12850 Stand, Mobile Horz.Mod 3 CFM56 132 72-00-00 856A2647G02 AT3523 PULLER,NO. 5 AGB GRSHAFT To remove Sealol seals or magnetic seals from AGB 132 72-63-00 856A2647G02 AT3524 PULLER,NO. 5 AGB GRSHAFT To remove Sealol seals or magnetic seals from AGB 132 72-63-00 856A2648G02 20007 SUPPORT, REAR FAN FRAME To support the rear of the fan frame to remove supports. 132 72-23-00 856A2655G02 20029 FIXTURE RAD.DR.SHFT RADIAL DRIVE SHAFT HSG ASSY/DISSY FROM FAN FRAME STRUT 132 72-23-00 856A2657G01 20161 Insp. Kit Central Vent tb To verify tightness of center vent tube 132 72-00-03 856A2660G01 20173 GAUGE MEASURE AXIAL CLR To measure dimension ZA through the STG2 Nozzle 132 72-54-00 856A2660G09 20307 GAUGE,MEASURE AXIAL LPT To measure dimension ZA through the stage 2 nozzle ASSY 132 72-54-00 856A2660G10 20063 GAUGE MEASURE AXIAL CLEAR TO MEASURE DIMENSION ZA THROUGH THE STG 2 NOZZLE 132 72-54-00 856A2661G01 12935 Puller aft rot. air/oil CFM56 132 72-00-03 856A2662G01 20162 Tool Kit Mast Air Nozzle To test aligment and calibrate air flow test rigs. 132 72-00-01 856A2663G01 12936 Puller splitter fairing CFM56 132 72-00-21 856A2664G01 20268 GAGE SETTING VBV DOORS To set the VBV doors in the closed position. 132 72-23-00 856A2666G01 20257 AIR TEST FIXTURE TO PRESSURE TEST THE FAN FRAME MODULE 132 72-00-01 856A2667G04 20171 Tool Check AD2 run out To check the AD2 Circular Run Out 132 72-00-01 856A2667G06 20223 A.D. FAN RUNOUT TOOL TO CHECK THE A.D. CIRCULAR RUNOUT ON THE FAN MAJOR MODULE 132 72-00-01 856A2668G02 20096 KIT PULLER ADAPTERS FITTED WITH A SLIDE HAMMER USED TO EXTRACT PARTS 132 72-00-00 856A2676G01 20144 Gauge Check Clr MO1B LPT To check clearance M01 132 72-54-00 856A2709G01 AT3465 GUIDE FWD SUPPORT TO MAINTAIN THE AXIAL AND RADIAL POSITION OF THE LPT SHAFT 132 72-00-03 856A2710G03 20312 FIXT. HANDLING LPT MAJOR Handling and transport of LPT Major Module 132 72-00-03 856A2711G01 20328 FIXTURE CENTER LPT SHAFT Hold LPT shaft/lpt case while handling LPT major module 132 72-55-00

856A2713G05 20053 FXT BLDUP LPT SHFT TO LPT ASSY/DISASSY OF MODULE 14 FROM MODULE 13/CHECK OF MAJ MODULE 132 72-00-03 856A2714G01 20051 FXT LIFT LPT MODULE TO HANDLE LPT ROTOR STATOR AND SHAFT 132 72-54-00 856A2716G01 AT3451 torque dispatching ring jet cell 132 856A2721G01 20262 PULLER, ROTATING AIR SEAL To separate stage 3 rotors air seal from stage 3 LPT DISK 132 72-54-00 856A2722G01 AT3453 fixt inst outer cooling jet cell 132 72-00-00 856A2722G01 AT3460 PINS, GUIDE TRF TO LPT TO POSITION TRF TO THE LPT MODULE 132 72-56-00 856A2727G01 20302 PULLER, RADIAL DRIVE SHFT To remove/install radial drive shaft 132 72-62-00 856A2730G03 20323 FIXT.ASSY/DISSY-LPTR To assemble/disassemble the LPT rotor/stator. 132 72-54-00 856A2731G02 20119 SECTORS SUPPORT LPT SHAFT TO REMOVE/INSTALL THE LPT SHAFT FROM THE LPT MODULE 132 72-55-00 856A2750G01 20254 FIXTURE LPT BLDS STG 1-4 TO ALLOW DISSY/ASSY of LPT blades 1, 2, 3 and 4. 132 72-54-00 856A2751G02 20064 TOOL SET LOCATING PINS TO POSITION THE NOZZLE SEGMENTS IN THE LPT CASE 132 72-54-00 856A2752G02 20075 HOOKS-RESTRAIN DSK TO LPT 132 72-54-00 856A2755G01 20065 TOOL SET SEALS TO CONE TO INSTALL FWD AIR SEALS ON LPT STUBSHAFT 132 72-54-00 856A2756G03 20097 DIFFUSER HEAT LPT SHAFT TO HEAT LPT SHAFT DURING ASSY OF MAJOR MODULE 132 72-54-00 856A2758G01 20318 FIXT.CNTR LPT SHFT 2 LPT Center LPT shaft to LPT during LPT major MOD Assy. 132 72-00-03 856A2760G02 20076 RNG SUPPT CONE STUD SHAFT TO TURN OVER THE CONE STUBSHAFT & DISK 3 DURING ASSY/DISSY 132 72-00-03 856A2764G03 20073 HEATER, LPT ASSY TO THERMALLY EXPAND THE LPT STUDSHAFT 132 72-54-00 856A2766G02 20177 Ring Supp Cone Stub Shaft Suppt stubshaft cone during removal of STG 3 Air Seal 132 72-54-00 856A2772G01 20150 Puller, Turbine Frame To separate the turbine rear frame from the LPT rear case 132 72-00-56 856A2773G01 20218 SPACR SUPPT LPTR/LPT CASE TO SUPPORT LPTR TO LPT CASE DURING ASSY/DISSY 132 72-00-03 856A2775G01 20066 PULLER, OIL SUMP ASSY TO REMOVE OIL SUMP ASSY AND AIR HEATER COVER 132 72-56-00 856A2780G02 20157 Handling adapter To facilitate installation of tool 856A2704 132 72-00-03 856A2785G01 20224 LIFT BEAM BALANCE & BSTR TO HANDLE THE BOOSTER BALANCING ASSEMBLY DURING BALANCING 132 72-21-00 856A2789G01 20229 RING CNTRG SHFT TO AIRSEL TO CENTER THE AFT ROTATING AIRSEAL ON LPT SHAFT. 132 72-55-00 856A2902G01 20321 DUMMY FAN DISK To simulate fan disk thickness during torquing/loosening nut 132 72-00-03 856A2903G01 20313 BEAM, TORQUE ADAPTATION To take up: Residual torque during rem/instal LPT CPLG NUT 132 72-00-03 856A2905G02 20326 WRENCH TORQUE/FAN DISK To torque/loosen the fan disk coupling bolts 132 72-21-00 856A2906G02 20314 GUIDE,COUNTERTORQ WRENCH To remove/install all major modules to clamp/loosen LPT nut. 132 72-00-03

856A2912G01 20309 FIXT. ASSY/DISY FAN BSTR To assy/dissy the fan and booster module and turn it over 132 72-23-00 856A2914G01 20315 TOOL SET,DISK TO BSTR To position the fan disk on the booster spool 132 72-21-00 856A2915G01 20308 BOOSTER SPOOL PROTECT RNG To protect booster spool at assembly/disassembly 132 72-23-00 856A2916G01 20303 TOOL SET,GUIDE PINS BSTR To guide fan stator 1-5 vane assemblies during assy 132 72-21-00 856A2921G01 20310 TEMPLATE,1-2 BRG TUBE To position the oil supply tubes during assembly OF TUBE 132 72-22-00 856A2923G02 20225 GUIDE #1 BRG SUPPORT TO GUIDE THE #1 BRG SUPPORT DURING REM. OF THE STAT OIL SEAL 132 72-22-00 856A2943G01 12937 Sleeve protection rear CFM56 132 72-55-00 856A3011P01 12938 Plug puller aft rot. CFM56 132 72-22-00 856A3012G02 12978 Puller #2 Brg. inner race CFM56 132 72-22-00 856A3013G03 20008 PULLER-N1 SPEED SENSOR RG To remove the N1 sensor ring. 132 72-22-00 856A3017G05 20030 TORQUE FIXT. #1 BRG HSG TORQUE/LOOSEN #1 BRG OUTER RACE NUT. 132 72-22-00 856A3030G01 20009 REAR FN STB SHFT LIFT EYE To handle fan stub shaft by it's rear end. 132 72-22-00 856A3033P01 12979 Nut Ret. #1 Brg. Sleeve CFM56 132 72-22-00 856A3034G04 12980 Puller Rot. air/oil Sep. CFM56 132 72-22-00 856A3057G05 12981 Fixt. torque center vent CFM56 132 72-55-00 856A3058G02 20010 PULLER #5 BRG INNER RACE To remove roller brg inner race from #5 brg. 132 72-55-00 856A3062G02 20011 PULLER,HYDR. REAR AIR/OIL To remove the rear rotating air/oil seal from LPT shaft. 132 72-55-00 856A3070G01 12982 Wrench radial drive shaft CFM56 132 72-62-00 856A3072G01 12983 Puller/pusher washer radi CFM56 132 72-62-00 856A3074G01 20176 Riverter Ball WT Booster To perform rivet flaring of fan disk balance weights. 132 72-21-00 856A3094G02 20256 BASEPLATE-ASSY/DISSY LPT TO ASSY/DISSY LPT COOLING MANIFOLDS 132 72-00-03 856A3097G03 12939 Puller LPT stub shaft CFM56 132 72-55-00 856A3100G04 20191 PIN LOCATING CNTR VENT TO POSITION AND LOCK THE CENTER VENT TUBE TO THE LPT SHAFT 132 72-00-03 856A3101G01 20263 PLUG,LOCATING CNTR VENT To perform angular positioning of cntr vent tube IN LPT SHAF 132 72-55-00 856A3104G03 20196 TUBE DUMMY LPT SHAFT PLUG TO CENTER THE CENTER VENT TUBE DURING BALANCE 132 72-56-00 856A3108G01 20197 GUIDE PIN #5 OUTER RACE TO GUIDE THE #5 OUTER RACE DURING INSTALLATION 132 72-00-03 856A3114G01 20214 WRENCH-CAPTIVE BOLTS VBV TO PERMIT INSTALL/REMOVE NUTS OF VBV BALLSCREW ACTUATOR 132 72-00-02 856A3115G01 20184 TOOL ADJUSTING VBV DOORS TO MANUALLY MOVE THE VBV DOORS AFTER REMOVING THE MOTOR 132 72-00-02 856A3234P01 12940 Protector center vent tub CFM56 132 72-00-02 856A3244G02 20258 GAP CHK N1 SPEED SENSOR To check the thickness of the shim for N1 speed sensor & rin 132 72-00-01 856A3246G01 AT3455 Guide alignment lpt/shaft jet cell 132 72-00-00 856A3247G03 12941 Guide align LPT shaft CFM56 132 72-00-00 856A3253G01 Hooks restrain air seal CFM56 132 72-00-03 856A3257G01 12942 Puller fwd rot. air seal CFM56 132 72-55-00 856A3260G02 12943 Plug extractor LPT shaft CFM56 132 72-00-03

856A3265G04 20261 FIXTURE, MACHINING To permit machining of No. 5 bearing outer race sleeve. 132 72-00-03 856A3266G01 20280 GUIDE PINS-TRF TO LPTCASE TO ALIGN THE TRF TO THE LPT CASE 132 72-00-03 856A3267G02 20122 1-2 BRG SUPT TEST RIG TO PROVIDE A MEANS TO CONNECT THE THE TEST RIG 132 72-22-00 856A3268G02 12944 Wrench nut center vent CFM56 132 72-00-03 856A3269G03 12945 Wrench nut #5 brg. inner CFM56 132 72-00-03 856A3272G01 12946 Puller #4 brg. rot. oil CFM56 132 72-55-00 856A3278G01 20178 PIN GURDE #5 BRG SUP LPT To center No. 5 Brg Support onto turbine frame during assy 132 72-56-00 856A3279G02 12947 Pusher/puller LPT disk CFM56 132 72-54-00 856A3283G01 20172 PLIERS, CRIMPING To crimp the straight pin for locking No.5 Brg 132 72-55-00 856A3308G04 12984 Puller #4 Brg. inner race CFM56 132 72-00-03 856A3315G01 12948 Puller center vent tube CFM56 132 72-00-03 856A3320G04 AT3449 LPT Assy & Dissy Jet cell 132 72-00-00 856A3322G03 12949 Tool crimp #5 brg. nut CFM56 132 72-55-00 856A3323G01 12950 Bushing centering #1 brg. CFM56 132 72-22-00 856A3328G01 20183 TOOL SET-1&2 BRG AIR CHEK TO PERMIT AIR INLET TO OIL NOZZLES DURING IMPGMT CHECK 132 72-22-00 856A3329G02 20226 TOOL SET TARGETS 1-2 BRG TO PERMIT VISUALIZATION OF AIR JET DURING OIL NOZZLE CHECK 132 72-22-00 856A3330G01 20084 TOOL SET AGB/TGB NIPPLE TO INSTALL O-RINGS AND CONNECTOR TUBES 132 72-62-00 856A3343G02 20179 TOOL SET PIN LOCATE NOZZL To locate the LPT Nozzle segments 132 72-54-00 856A3344G04 20031 NO.1 BRG HSG PULLER TO REMOVE NO.1 BRG HSG FROM NO. 1 SUPPORT 132 72-22-00 856A3358G02 20163 Fix Holdin No.4 Brg Race To hold No.4 brg inner race attachements bolts during instal 132 72-55-00 856A3358G03 20192 FIXT. NO 4 BRG INNER BOLT TO HOLD THE NO 4 BRG INNER RACE BOLT DURING INSTALLATION 132 72-55-00 856A3383G01 12985 Fixt. align LPT frame CFM56 132 72-00-03 856A3385P03 12951 Wrench stg. 1 LPT disk CFM56 132 72-54-00 856A3386G04 20278 HEATER-LPT SHAFT TO THERMALLY EXPAND THE LPT STUB SHAFT TO INSTALL IN ROTOR. 132 72-55-00 856A3389G01 20012 PULLER,ROLLER BEARING To remove radial drive shaft roller brg inner race. 132 72-62-00 856A3392G01 12986 Wrench torq. Aft Rot Air/ CFM56 132 72-00-03 856A3409G01 12952 Pins guide spinner rear CFM56 132 72-00-02 856A3410G01 20248 RING, DISTRIBUTION-TORQUE To show torque sequence of nuts SECURING LPT 132 72-55-00 856A3413P02 20249 RING,HOLDING-NO4 BRG RLLR To hold No.4 bearing rollers during the balancing OPERATION 132 72-55-00 856A3415G02 20211 TOOL SET CONICAL SUPPORT TO CENTER AND HOLD THE STG 3 SEAL ON THE CONICAL ROTOR SUPPT 132 72-00-03 856A3419G02 12953 Adpt. puller oil inlet CFM56 132 72-00-03 856A3426G01 20264 PULLER, STATNARY AIR SEAL To remove the stage 1 LPT nozzle stationary air seal 132 72-54-00 856A3432G01 20164 Gage, Tool Feelers To sheck seating of the LPT Shaft 132 72-55-00 856A3433G01 20202 TOOL SET TRUNNIONS TO HANDLE THE LPT ROTOR STATOR MODULE 132 72-00-03 856A3435G01 20250 ADAPTER, BLADE ROOT adapt blade root for static moment msrmnt of STG 1-4 LPT 132 72-54-00

856A3439G03 20154 Ring, Protective Bearing To protect the locating diamenter the front of the LPT 132 72-00-03 856A3440G02 20198 PULLER RING BRG TO EXTRACT THE PROTECTIVE BRG AFTER LPT BALANCING 132 72-00-03 856A3443G04 12987 Puller outer race #5 Brg. CFM56 132 72-00-03 856A3445G02 20013 LPT MOD LIFT & TURN TRUNN To lift & turn LPT module. 132 72-00-03 856A3450G02 20222 FIXT BAL. LPT ROTOR STTR TO BALANCE THE LPT ROTOR STATOR AND LPT MODULE 132 72-00-03 856A3452G01 20165 Stand Buildup vertical To assemble LPT Major Module in vertical position 132 72-00-03 856A3453G01 20199 TRANSFER DOLLY FOR LPT TO TRANSFER THE LPT MODULE FROM ASSY TO BALANCE 132 72-00-03 856A3455G01 20251 ADAPTER,DRIVE FWD LPT SHF drive LPT shaft during balancing 132 72-55-00 856A3458G01 20200 BASEPLATE FOR LPT DISKS TO PROVID EFOR THE STATIC BALANCE OF THE LPT BLADED DISKS 132 72-54-00 856A3460G06 20194 FIXT.CHK-CNTR VNT TUBE TO CHECK THE OUTERDIAMETER OF THE CENTER VENT TUBE SUPPORTS 132 72-00-03 856A3463G01 12954 Lever countertorque LPT CFM56 132 72-00-21 856A3473G01 20193 CENTER VENT TUBE MASTER TO CALIBRATE THE CENTER VENT TUBE SUPPORTS AXIAL POSITION 132 72-55-00 856A3474G01 20219 MASTER FOR 856A3472 TOOL TO CALIBRATE THE CENTER VENT TUBE AXIAL POSITION 132 72-00-03 856A3480G01 20246 RING,CKNG CNTR VENT TUBE To check outer diameter of center event tube inner supports 132 72-55-00 856A3486G01 20175 Tool Assy, Seal Cent Vent To install the damper seals on the LPT Shaft Vent tube 132 72-55-00 856A3487G01 20085 PROTECTOR #4 BALL BRG TO PROTECT #4 BALL BEARING 132 72-00-03 856A3488G01 AT3464 SUPPRT HOLD FIXT,LPT SHFT FIXTURE USED TO SUPPORT LPT SHAFT DURING DISSY AND ASSY 132 72-00-03 856A3489G01 20325 TOOL SET TARGET NO. 1BRG To perform air impingement check of the No. 1 brg oil nozzle 132 72-22-00 856A3500G01 12955 Adpt. puller fan blade sp CFM56 132 72-00-21 856A3501G02 12988 Fixt. Aling/guide BSTR CFM56 132 72-00-01 856A3501G04 20098 ALIGNMENT GUIDE-LPT/BSTER TO ALIGN THE GUIDE BOOSTER RELATIVE TO THE LPT SHFT RMVL/INT 132 72-00-03 856A3502G05 12989 Fixt. guide/counter torqu CFM56 132 72-00-01 856A3504G03 20014 FIXTURE,PUSHER/PULLER To remove/install module 1 and major module 3. 132 72-00-01 856A3506G02 12990 Wrench torque LPT Cplg. CFM56 132 72-00-03 856A3507G01 20275 GUIDE-FWD SUPPORT TO MAINT. AXIAL & RADIAL POSITION OF LPT SHAFT DRG ASSY/DISY 132 72-00-01 856A3508G01 20015 SLEEVE,CENTERING/REMOVAL To center and remove/install module 1 and major module 3. 132 72-00-01 856A3509G01 20016 ADAPTER,LOCKING CORE ENG. To prevent rotation of core eng.during assy/dissy of LPT mod 132 72-00-63 856A3512G02 20042 FAN DISK, DUMMY TO SIMULATE FAN DISK THICKNESS DURING TORQUE/UNTORQUE LPT NT 132 72-00-01

856A3513G04 20017 BEAM, RESIDUAL TORQUE TO TAKE UP RESIDUAL TORQUE DURING ASSY/DISSY OF LPT COUP.NUT 132 72-00-01 856A3514P02 20018 ADAPTER, RESIDUAL TORQUE TO TAKE RESIDUAL TORQUE DURING ASSY/DISSY LPT COUP. NUT 132 72-00-01 856A3515G03 20019 EXTNTION BEAM,VAR.CG LIFT TO ADAPT VARIABLE CG LIFT FIXTURE TO MOD.1 & 2 HANDLING TOOL 132 72-00-01 856A3516G01 20153 Sleeve Protector Fan Disk To protect the fan disk balance weights during mod 1 & mod 2 132 72-00-21 856A3517G02 20020 ADAPTER, COUNTERTORQUE TO TAKE UP COUNTERTORQUE DURING MAJOR MOD.3 ASSY/DISSY. 132 72-00-01 856A3524G01 20021 BOOSTER & LPT TOOL DRIVE TO REMOVE/INSTALL BOOSTER OR LPT MAJOR MODULE. 132 72-00-01 856A3525G04 20050 CRADLE,REMOVE/INSTALL AGB TO REMOVE/INSTALL AGB OR DUMMY AGB FROM/ON ENGINE 132 72-00-62 856A3531G02 20201 GRBX ASSY DUMMY TO HOLD THE FAN CASE DURING MACHINING OF ABRAIDABLE COATING 132 72-00-01 856A3539G02 20036 PULLER,TIGHT BOLT BOOSTER TO REMOVE/INSTALL FAN DISK TO BOOSTER SPOOL ATTACHMENT BOLTS 132 72-21-00 856A3542G01 20269 WEIGHT,AXIAL LDNG N3BRG simulate axial loads applied to No. 1 bearing 132 72-22-00 856A3543G01 20270 TOOL SET, CHECK GAGE check gap between end of bolts securing FWD/ATF RET SEALS 132 72-21-00 856A3544G03 20022 ADAPTER FLANGE-TRANS.GRBX TO HOLD THE TRANSFER GRBX DURING FINAL ASSY & SEALING TEST. 132 72-62-00 856A3550G02 20037 PULLER TOOL SET, AGB TO REMOVE BEARING FROM ACCESSORY AND TGB. 132 72-63-00 856A3551G01 12956 Tool set inst/rem TGB adp CFM56 132 72-62-00 856A3552G01 12957 Fixture holding radial CFM56 132 72-62-00 856A3553G03 12991 Fixt. lock input & horizo CFM56 132 72-62-00 856A3555P01 12958 Socket stalok nut CFM56 132 72-62-00 856A3556G01 20189 WEIGHT AXIAL LOADING NO 1 TO LOAD THE NO 1 BRG WHEN TAKING THE LHA34 DIMENSION 132 72-22-00 856A3558P01 12992 Wrench deflector bolts CFM56 132 72-62-00 856A3561G01 12959 Wrench stalok nut CFM56 132 72-62-00 856A3567G03 12993 Tool set pads puller AGB CFM56 132 72-63-00 856A3570G01 12994 Wrench #2 Brg. inner race CFM56 132 72-22-00 856A3571G02 20023 WRENCH-FORWARD ROTATING TO TORQUE/LOOSEN FORWARD ROTATING AIR/OIL SEPARATOR NUT. 132 72-22-00 856A3572G01 20024 WRENCH,#1 BRG RACE NUT TO TORQUE/LOOSEN NO.1 BRG INNER RACE NUT 132 72-22-00 856A3573G03 AT3489 No.1 & 2 Brg Support To suppt No.1 & No.2 BRG Support during Assy and Dissy 132 72-22-00 856A3575G01 20025 PULLER,#1 BRG INNER RACE TO REMOVE THE 2 INNER RACE HALVES OF THE NO.1 BRG. 132 72-22-00 856A3576G01 12960 Rem/inst. sealol/mag seal CFM56 132 72-63-00 856A3580G03 20290 FIXT. MACHINE FAN CASING To machine fan casing abradable strip. 132 72-00-01 856A3591G01 20026 PROTECTOR, MOUNTING PIN TO PROTECT THE PIN THREADS DURING ASSY/DISSY OF AGB. 132 72-00-62

856A3600G01 12961 Puller radial drive shaft CFM56 132 72-00-62 856A3604P01 12962 Wrench horz. drive shaft CFM56 132 72-00-62 856A3606G03 12963 Tools set puller pads TGB CFM56 132 72-62-00 856A3608G01 20166 Fix axial load strip Mach To pull the fan shaft or LPT shaft during abradable strip 132 72-00-01 856A3610G01 20228 FIXT. TO CHECK DIM. "V" CHECK DIMENSION "V" AFTER ASSY OF 1-2 BRG SUPPORT 132 72-22-00 856A3618G01 20271 TOOL SET, PUSHERS install stationary air/oil seal, oil baffle, 132 72-22-00 856A3621G02 20174 Pin Guide To install booster stator vane assembly stage 1 on stage 2 132 72-21-00 856A3626G01 20227 FRAME FRAME INSP TOOL TO CHECK ACOUSTICAL PANEL CONCENTRICITY 132 72-23-00 856A3628G01 20187 NO.1 BRG INNER RACE TOOL TO INSTALL THE NO 1 BRG REAR INNER RACE 132 72-22-00 856A3702G02 20099 CENTERING SLEEVE MODULE 3 TO CENTER MAJOR MODULE 3 DURING INSTALL/REMOVAL 132 72-00-03 856A3703G01 20077 GUIDE-COUNTRTORQUE WRENCH TO PROVIDE COUNTERTORQUE DURING LOOSING OF LPT SHAFT NUT 132 72-00-03 856A3703G01 20100 GUIDE-COUNTERTORQ. WRENCH TO PROVIDE COUTERTORQUE DURING LOOSEN/TORQUING LPT SHAFT 132 72-00-03 856A3704G01 20055 BEAM, TORQUE ADAPTATION PROVIDE COUNTERTORQUE DURING REMOVAL & INSTALL OF LPT MODULE 132 72-00-03 856A3704G01 AT3536 BEAM, TORQUE ADAPTATION The tool is used to provide countertorque during assy/dissy 132 72-21-00 856A3706G01 AT3466 SECTOR-CTR LPT SHFT FWD TO KEEP THE LPT SHFT CENTRED DURING INSTALL/REMOVE 1-2 BRG 132 72-00-61 856A3707G05 AT3500 FAN BLADE SPACER PULLER TO PULL AND REMOVE FAN BLADE SPACERS 132 72-00-01 856A3708G01 AT3457 PUSH/PULL RADIAL DR. SHFT TO INSTALL AND REMOVE RADIAL DRIVE SHAFT 132 72-00-62 856A3709G02 AT3458 FIXTURE, ALIGNMT AGB TO PUT AGB IN LINE WITH THE ENGINE DURING INSTALLATION 132 72-00-63 856A3721G01 AT3469 ADAPTER TOOL 1-2 BRG USED TO HANDLE THE 1 AND 2 BRG SUPPORT 132 72-22-00 856A3722G02 20149 FAN DISK DUMMY To remove or install #1 brg support on the 12-strut hub 132 72-00-01 856A3723G02 AT3479 FIXT. GUIDE/PULL BOOSTER TO GUIDE AND PULL THE FAN/BOOSTER MODULE DURING INSTALL/RMVL 132 72-21-00 856A3723G02 AT3539 FIXT. GUIDE & PULL BSTR To guide the fan and booster during install/remove 132 72-21-00 856A3725G02 20272 TOOL SET, GUIDE PINS to guide stage 2,3 and 4 vane ASSY DURING BOOSTER ASSY 132 72-21-00 856A3728G01 20101 CORE ENGINE LKNG ADAPTER TO LOCK THE CORE FROM MOVING DURING INSTALL/REMOVAL 132 72-00-02 856A3731G01 20259 FIXT. HANDLING - FAN DISK The fixture is used to handle and turn the fan disk. 132 72-00-01 856A3732G02 AT3476 HANDLNG FIXT. BOOSTER TO HOLD THE FAN&BOOSTER ASSY DURING ASSY/DISSY 132 72-21-00 856A3732G02 AT3533 FIXT. HANDLE FAN BOOSTER TO HOLD THE FAN&BOOSTER ASSY DURING ASSY/DISSY 132 72-21-00 856A3734P02 20244 WRENCH,CNTRNG PIN BSTR SP LOOSEN/TORQUE BOOSTER SPOOL THREADED PIN NUT 132 72-21-00 856A3738G01 20185 FIXT-TORQ/LOOSE #1BRG NUT TO TORQUE/LOOSEN #1BRG OUTER RACE NUT 132 72-22-00

856A3739G01 20245 FIXTURE,INST OIL NZ BRG#2 TO install the No 2 bearing oil NOZZLE 132 72-22-00 856A3741G01 20273 TOOL CHECKING GAP check value of gap between speed sensor ring & N1 SPD SENSOR 132 72-22-00 856A3746G02 20159 TOOL ASSY/DISSY RAD SHFT TO ASSEMBLE/DISASSEMBLE THE RADIAL DRIVE SHAFT 132 72-00-01 856A3748G01 20086 PROTECTION COVER -LPT DSK TO PROTECT THE STG 1 LPT BLADES DURING ASSY/DISSY 132 72-54-00 856A3749G01 20067 TOOL SET LPT STG 2&3 SEAL TO INSTALL THE LAST SEALING PLATE DURING ASSY OF 2&3 SEAL 132 72-54-00 856A3750G02 20056 FIXTR-CTRG LPT SHAFT MOD TO HOLD THE LPT SHAFT/LPT CASE WHILE HANDLING LPT MODULE 132 72-00-03 856A3750G02 AT3527 FIXT.CENTERING LPT SHAFT The tool is used to hold LPT shaft while HDLG the LPT Major 132 72-00-03 856A3750G02 AT3528 FIXT.CENTERING LPT SHAFT The tool is used to hold LPT shaft while HNDLG THE LPT MAJOR 132 72-00-03 856A3751G03 20068 RING HOLDING T-1 OAS TO HOLD THE T-1 OAS IN THE LPT DURING INSTALL. OF LPT SHOUD 132 72-54-00 856A3752G04 20123 FIXT. REML STG 1,2,3 OAS TO REMOVE THE STAGE 1,2,3 OUTER STATIONARY AIRSEAL 132 72-54-00 856A3755P01 20069 TOOL INSTALL-LPT STG 1&2 TO ALLOW INSTALL. OF 1&2 ROTATINGF AIRSEALS DURING LPT ASSY 132 72-54-00 856A3756G01 20255 FIXTURE, INTSLLTN SHIELD INSTALL STG 2 HEAT INSULATION PLATE IN THE LPT 132 72-54-00 856A3757G02 20265 FIXTURE, INST SHIELD LPT3 to install the stage 3 heat insulation IN LPT 132 72-54-00 856A3759G02 AT3456 SECTOR HANDLING TURBINE TO HANDLE THE TURBINE FRAME MODULE 132 72-56-00 856A3762G03 20124 FIXT.ASSY/DISSY LPTR STTR USE TO DISSY/ASSY THE LPTR ROTOR/STATOR & CHECK DISK FLATNES 132 72-54-00 856A3768G01 20252 Wrench, Assy/DssY To torque/dissy stg 1&2 disks 132 72-00-03 856A3773G01 20131 FIXT.-HANDLG LPT MODULE TO HANDLE AND TRANSPORT THE LPT MODULE 132 72-00-03 856A3773G01 AT3521 FIXT,HNDLG - LPT MAJOR The fixture is used to handle and to transport the LPT MAJOR 132 72-00-03 856A3773G01 AT3522 FIXT,HNDLG - LPT MAJOR The fixture is used to handle and to transport the LPT MAJOR 132 72-00-03 856A3778G01 20215 GUIDE PINS-SPINNER CONE R TO INSTALL THE FAN RETAINING FLANGE TO THE SPINNER REAR CONE 132 72-00-01 856A3779G02 AT3459 PULLER PLATFORM-FAN BLDE TO REMOVE FAN BLADE PLATFORMS 132 72-00-22 856A3780G01 20247 KIT,RMV/INST AGB/TGB BRGS to tighten/loosen bearing inner race NUTS 132 72-62-00 856A3782G02 20216 WRNCH REMVL FAN BLD RTNR TO REMOVE AND INSTALL THE FAN RETAINING RING FROM FAN DISK 132 72-00-01 856A3788G01 20107 TOOL SET INSTALL LPT OAS 132 72-00-03 856A3789G01 20220 TOOL SET PULER REAR DUCT TO REMOVE OR INSTALL THE SPACER FROM THE REAR VENT TUBE 132 72-00-03 856A3790G01 20221 FIXT. PUSH/PULL VENT DUCT TO REMOVE REAR VENT TUBE FROM THE LPT SHAFT 132 72-00-03 TO MACHINE THE NO.5 BRG OUTER RACE ADJUSTING 856A3791G03 AT3462 FIXT. MACH.-SLVE #5 BRG SLEEVE 132 72-00-03

856A3792G01 AT3448 LPT shaft Centering Fixtu L P T 132 72-00-00 856A3793G01 AT3478 FIXT.-PUSHER/PULLER CVT TO INSTALL AND REMOVE THE CENTER VENT TUBE FROM THE LPT 132 72-55-00 856A3794G01 20087 OUTER RING - T-1 OAS TO HOLD T-1 OAS AND SHROUD SUPPORT DURING TRANSPORTATION 132 72-53-00 856A3795G01 20088 STAND-MOBILE, LPT MODULE TO ASSEMBLE/DISASSEMBLE LPT MODULE OR TO STORE LPT MODULE 132 72-54-00 856A3799G01 20070 GUIDE PIN #5 BRG SUPPORT 132 72-54-00 856A3906G01 AT3480 FIXT. TORQ. C-1 DISK CPLG TO INDEX AND TORQUE THE FAN DISK COUPLING BOLTS 132 72-21-00 856A3906G01 AT3534 FIXT. TORQUE C1 DISK CPLG TO INDEX AND TORQUE THE FAN DISK COUPLING BOLTS 132 72-21-00 856A3907P01 AT3481 C-1 DISK PROTECTOR TO PROTECT THE C-1 DISK DURING ASSY/DISSY 132 72-23-00 856A3908G02 20108 PULLER STG 1 STATIONARY PULLER USED TO REMOVE THE STG 1 STATIONARY OUTER AIRSEAL 132 72-53-00 856A3910G01 20152 Support Table Support Table 132 72-00-03 856A3913G02 20125 FIXT. CHK ASSY TRF NO.5 USED TO CHECK ASSY TRF/NO.5 BRG SUPPORT 132 72-56-00 856A3914G01 20217 TOOL SET BOLTS TO BSTR TOOL SET FITS BOLTS FAN DISK TO BOOSTER SPOOL 132 72-00-01 856A3915G01 20109 PIN FOR OIL COLLECTOR TO INSTALL THE OIL COLLECTOR ON THE LPT FRAME 132 72-56-00 856A3917G01 20167 CNTR VENT TUBE NUT TO ALLOW THE TORQUING OR LOOSENING OF THE CENTER VENT TUBE 132 72-54-00 856A3918G02 20188 FIXT-PULLER PRESS NO 2 TO REMOVE/INSTALL THE NO 2 ROLLER BRG OUTER RACE 132 72-22-00 856A3919G01 20170 Heater To heat the No.2 Brg housing before install the outer race 132 72-22-00 856A4055G10 AT3510 BLADE TIP GRINDER-HPC The grinder is used to grind the blade tips of THE HPC BLADE 132 72-00-02 856A4633G02 AT3519 FAN DISK DOVETAIL GAGE The tool is used to perform measurement of the FAN DISK SLOT 132 72-23-00 856AHSGADAPTER AT3529 HIGH SPEED GRINDER ADPTRS USED AS ADAPTERS AND SPACERS TO ENGAGE THE HPCR ON THE HSG 132 72-31-00 856ASW81046 12965 Sweeney Female Adapter CFM56 132 72-22-00 AT02T2008-001 AT3530 TOOL, HPC/IGB SEPARATOR To separate the HPC section from the gearbox bearing 132 72-00-03 856A1056G05 20281 FIXTURE,GRIND-CMPSR STTR. To restrain forward and aft stator cases during liner grind 232 72-30-00 856A1077G02 AT3507 PIN SET ALIGN HPT DISK TO HPT SEAL 232 72-52-00 856A1097G01 AT3508 SCREW SET TO HOLD NUT SHIELD IN THE COMBUSTOR CASE 232 72-41-00 856A1135G02 20291 HPT GRIND FIXTURE TO RESTRAIN HPT SHROUD DURING SURFACE GRIND OF INSIDE DIA 232 72-53-00 856A1156G01 20295 PYLON, INDICATOR - COMPRE To mount and position the runout indicating devices.compre 232 72-31-00 856A1166G02 20296 SLING, LIFT HPTR BALNC LIFTS HPTR TO HORIZONTL POS DURING BALANCE AND ASSY 232 72-52-00

856A1212G11 20324 HPC GAGE SET To inspect the length of the HPCR blades. 232 72-31-00 856A1213G01 AT3506 PIN SET ALIGNMENT TO ALIGN HPTR TO SHAFT 232 72-52-00 856A1256G01 20297 GAGE SET,LINER DIAMETER To measure the stator rear case liners to determine DAMAGES 232 72-33-00 856A1412G06 20282 FIXTURE,ASSY-DISSY MOD 10 HOLD MOD 10 SO THAT INNER FRONT & REAR SUPTS CAN BE ASSEMBLD 232 72-51-00 856A1457P07 20299 Plierench HPT Ring Rmvl to remove aft hpt split ring 232 72-52-00 856A1600G01 20292 HPT BLADE RETAINER RESTRAINS HPT BLADES DURING PRELIMINARY BALANCE 232 72-52-00 856A1603G03 20283 FIXTURE,INST/RMV-HPTRSEAL TO RMVE/INSTL HPT ROTOR FWD OUTER SEAL 232 72-52-00 856A2759G01 20284 TOOL SET, PULLER SEALS To rmve fwd air seal &rotating oil seal from stubshaft cone 232 72-54-00 856A3063G02 AT3509 PULLER REAR RTTNG AIRSEAL PULLER FOR THE REAR ROTATING AIR SEAL 232 72-55-00 856A3063G02 AT3518 PULLER,REAR ROTATNG SEAL PULL THE REAR ROTATING SEAL FROM LPT SHAFT 232 72-55-00 856A3102G02 20285 STAND,INST #4BRG INR RACE TO INSTL #4 BRG ONTO LPT SHAFT 232 72-55-00 856A3276G01 20293 RING,STRENGTHENING STRENGTHENS LPT CASE REAR FLANGE DURING ASSY 232 72-54-00 856A3416G01 AT3415 PULLER,ROTATING AIR SEAL PULL 3RD STG ROTATING AIR SEAL FROM THE CONICAL SUPPT 232 72-54-00 856A3451G03 20294 BALANCE RIXTURE LPT MAJOR TO BALANCE LPT MAJOR MODULE.. 232 72-54-00 856A3472G01 20286 TOOL,CHKNG AXIAL POSITION TO CHK AXIAL POSITION OF CENTER VENT TUBE ON LPT SHAFT 232 72-55-00 856A3526G03 AT3511 BASEPLATE- MOBILE BOOSTER TO ASSEMBLE/DISASSEMBLE BOOSTER 232 72-21-00 856A3528G01 AT3512 BLOCK SUPPT, BOOSTER SPL TO SUPPORT BOOSTER SPOOL 232 72-21-00 856A3535G02 AT3514 LIFT FIXTURE,BOOSTER ASSY LIFT BOOSTER DURNG ASSY/DISSY OF STG4 VANE ASSY AND FOR BALC 232 72-21-00 856A3536G01 AT3513 SPT LOCATOR,BOOSTER RTR TO SUPPT/ LOCATE BOOSTER ROTOR DURING DISSY/ASSY 232 72-21-00 856A3537G01 20287 TOOL,CHKNG POSITION AGB TO CHK & ADJUST POSITION OF AGB DURING INSTALLATION 232 72-63-00 856A3562G02 AT3516 TOOL SET REMV/INSTL OIL REMOVE/INSTLL HORIZ GRSHFT OIL DISTRIBUTOR 232 72-62-00 856A3566G03 AT3517 TOOL SET,PUSHERS AGB RMV/INSTLL hndcrkng,inpt drv gr,fuel PUMP BEVEL DRV GEAR 232 72-62-00 856A3582G01 AT3515 WRENHC,LPC FWD RTNG SEAL REMV/INSTL FWD AIR SEAL/AFT BLADE RETNR IN BOOSTER 232 72-21-00 856A3740G01 20288 TOOL CHKNG # 2 BRG TU CHECK #2 BRG OIL JETS DURING IMPINGMENT TESTS 232 72-22-00 856A3783G02 20289 FIXTURE,CHKNG #1&2 BRGSUP TO CHECK #1&2 BRG SUPPT CONCENTRICITY AND VALUE OF A DIMNSN 232 72-22-00 865A6629G03 20298 GAGE-FAN DISK DVTL SLOTS TO CHECK WEAR ON PRESS FACES OF FAN DISK 232 72-21-00