IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction. The most updated information on this Certificate of Listing is available online at pld.iapmo.org Effective Date: not available -Rev. 10/4/2012-3689 Arrowhead Drive Carson City, NV 89706 Identification: Each product shall bear permanent and legible markings to identify the manufacturer. This marking shall be the trade name, trademark, or other mark known to identify the manufacturer. The product shall bear the appropriate IAPMO R&T certification mark. The product may also bear either "Lead Free" or "Low Lead" above or in close proximity to the IAPMO R&T certification mark. Characteristics: Products may include any pipe, pipe fitting, solder, flux, or other plumbing products providing water for human consumption. Products listed below are to be installed in accordance with the manufacturer's instruction. These products have been verified with weighted average lead content <=0.25%; Solder and flux lead content <=0.2%. Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025. Products are in compliance with the following standard(s): Section 1417(d) of the Safe Drinking Water Act This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material, manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing. Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc. Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.
The lead content requirements of Section 116875 of the California Health & Safety Code
MODELS: Water Heater Hose Connector 12", 18", 24 and 36" long SFF-06312, SFF-06314, SFF-06318, SFF-06324, SFF06336 Water Heater Hose Connector 12", 18", and 24" long PPC-112-PP, PPC-118-PP, PPC-124-PP, PPC-148-PP, Water Heater Hose Connector 12", 18", and 28" long (optional 48" long) HWH-112-PP, HWH-118-PP, HWH-124-PP Water Heater Hose Connector 48" long HWH-148-PP Ice Maker Hose Connector 24", 60", 72", 84", 96", 120", and 180" long. KDW-924-PP, KDW-960-PP, KDW-972-PP, KDW-984-PP, KDW-996-PP, KDW-9120-PP, KDW-120-PP, KDW-912-PP Ice Maker Hose Connector 12" long(optional 24", 60", 72", 84", 96", 120", and 180" long) SFF-100XX-ZZ: 1" FIP w/gasket x 1" FIP w/gasket 1" tubing, inside diameter XX = 12",18",24",36",48" SFF-125XX-ZZ: 1-1/4" FIP w/gasket x 1-1/4" FIP w/gasket 1-1/4" tubing, inside diameter. XX = 18",24",36" SFF-PUL-02259: FEMALE OEM x 1/4" FIP Metal Cone 7/32" tubing, inside diameter SFF-PUL-02259.0: FEMALE OEM x 1/4" FIP Metal Cone 7/32" tubing, inside diameter SFF-PUL-02260: FEMALE OEM x 1/4" FIP Metal Cone 7/32" tubing, inside diameter TFC-1XX-ZZ: 3/8" OD compression x 3/8" metal compression cone 5/16" tubing, inside diameter. XX = 9",12",16",20",30" WFF-1XX-ZZ: ¾" FIP w/gasket x ¾ FIP w/gasket 5/8" tubing, inside diameter. XX = 12",18",24" ZZ =Customer packaging code Note: *denotes XX= Hose connector length II. OEM PART NUMBERS: U 025 XX J2 Y1 H A B C D E F LEGEND: A. = Extrusion Type and Over Braiding: P = UltraCore with nylon over braiding U = UltraCore with stainless steel over braiding V = Reinforced Vinyl (PVC) Tubing with no over braiding B = Extrusion Inside Diameter Size in Inches: 0.25", 0.31" Page 3 of 6
C = Overall Length in Inches: 24" thru to 300" D = First End Connection Code: Code Used on Extrusion Size Description Size Description H4 0.31 Male Fitting 1/2-14 NPT I1 0.31 3/8" Compression J1 0.25 1/4" metal compression cone N4 0.31 1/2" metal compression cone E = Second End Connection Code: Same as First End Connection Code "D" above. H4 for.031 hose liner can only be used with N4 F = Specific Code: 1 = Single Package 2 = Packaged in Pairs (blank) = Bulk G = Bag P = Plumber's Pack R = Retail Package L = Bilingual Label H = Header Card Note: * Specific codes can be used in any combination III. Copper Corrugated Water Heater Connector WCP-1XX-PP 3/4"FIP X 3/4"FIP WCP-2XX-PP 3/4"FIP X 3/4"SWEAT WCP-3XX-PP 3/4"FIP X 3/4"PEX WCP-1XX-AP 3/4"FIP X 3/4"FIP with Adaptor WCP-2XX-AP 3/4"FIP X 3/4"SWEAT with Adaptor WCP-3XX-AP 3/4"FIP X 3/4"PEX with Adaptor XX indicates length. 12",18",24" WCP-3XX-SERIES 18", 24" only Stainless steel corrugated water connectors WCS-1XX-PP 3/4" FIP x 3/4" FIP WSS-1XX-PP 3/4" FIP x 3/4" copper/brass Sweat adaptor WCS-3XX-PP 1" FIP x l" FIP Ice Maker and Stop Valves V-101-A-LL V-101-S-LL V-102-A-LL V-102-S-LL V-103-A-LL V-103-S-LL V-104-A-LL Page 4 of 6
V-104-S-LL V-107-A-LL V-401-A-LL V-401-A-LL V-402-A-LL V-402-S-LL Stop Valves P-06239-LL P-06288-LL P-06296-LL P-06302-LL P-06335-WBLL P-06422-LL P-06293-LL P-06258-LL OB-504-LL ICEMAKER BOX, METAL, WITH OB-504-T-LL ICEMAKER BOX, METAL W/ OB-507-LL ICEMAKER BOX, METAL OB-509-LL ICEMAKER BOX,METAL,WHITE OB-509-TLL ICEMAKER BOX,METAL,WHITE OB-518-LL ICEMAKER BOX, METAL, OB-518-TLL ICEMAKER BOX,METAL,WHITE OB-800-LL ICEMAKER BOX, BEIGE, OB-800-TLL ICEMAKER BOX, BEIGE, OB-8010-LL OB-8010-TLL OB-801-LL, OB-801-TLL ICEMAKER BOX WHITE OB-8110-LL OB-8110-TLL OB-817-LL, MIP/ OB-817-TLL, MIP/ OB-818-LL, PEX OB-818-TLL, PEX OB-824-LL OB-824-TLL OBFS-8010-LL ICEMAKER BOX, FIRESTOP OBFS-8010-TLL ICEMAKER BOX, FIRESTOP OBFS-8110-LL ICEMAKER BOX, FIRESTOP OBFS-8110-TLL ICEMAKER BOX, FIRESTOP OBPS-101-RK-LL 1/2" Sweat Pull-Stop Box rough in assembly with valve installed OBPS-102-RK-LL CPVC Pull-Stop Box rough in assembly with valve installed OBPS-103-RK-LL PEX (ASTM F2159) Pull-Stop Box rough in assembly with valve installed OBPS-104-RK-LL PEX (ASTM F1960) Pull-Stop Box rough in assembly with valve Installed P-06425-LL 1/2" PEX (ASTM F 2080) x 1/4" OD Compression Nickel Handle P-06435-LL 1/2" PEX x 1/4" OD comp, Nickel Plated Handle Page 5 of 6
P-06436-LL P-06440-LL P-06441-LL P-06442-LL P-06443-LL P-06447-LL P-06462-LL P-06463-LL P-06466-LL P-06467-LL 1/2" PEX x 3/8" OD comp, Nickel Plated Handle 1/2" MIP/1/2" Sweat x 3/8" OD Compression Nickel Handle 1/2" MIP (or 1/2" female sweat) x 3/8" OD Compression, Nickel handle 1/2" PEX (ASTM F 1807) x 3/8" OD Compression Nickel Handle 1/2" PEX x 3/8" OD Compression, Nickel handle 1/2" Wirsbo PEX x 3/8" OD Compression, Nickel handle 3/8" PEX (ASTM F 1807) x 1/4" OD Compression Nickel Handle 3/8" PEX (ASTM F 1807) x 3/8" OD Compression Nickel Handle 3/8" PEX x 1/4" OD Compression, Nickel handle 3/8" PEX x 3/8" OD Compression, Nickel handle Fire Stop Pull Stop Outlet Box Model No. OBFPS-101-RK OBFPS-102-RK OBFPS-103-RK OBFPS-104-RK OBFPS-101-RK-LL OBFPS-102-RK-LL OBFPS-103-RK-LL OBFPS-104-RK-LL Description 1/2" M.I.P./Sweat Pull-Stop Box and valve assembly CPVC Pull-Stop Box and valve assembly PEX (Vanguard and Zurn) Pull-Stop Box and valve assembly Wirsbo Pull-Stop Box and valve assembly 1/2" Sweat Pull-Stop Box and valve assembly Tested CPVC Pull-Stop Box and valve assembly PEX (Vanguard and Zurn) Pull-Stop Box and valve assembly Wirsbo Pull-Stop Box and valve assembly Page 6 of 6