Catalogue January 06 Technical catalogue SMISSLINE TP-Touch proof system Power and safety
Power behind bars The world s safest socket system Small cause, large effect: as the world s first pluggable socket system, SMISSLINE TP ensures that load-free devices and components can be snapped on and off under voltage without the need for additional personal protective equipment to guard against electrical hazards. That opens up completely new prospects for you when it comes to installation, operation and flexibility. 0/ CCC45059C003 ABB Technical catalogue SMISSLINE TP
Efficiency you can touch Plug in components during ongoing operation Even safer: Protection against electrical hazards We have upgraded our unique SMISSLINE TP socket system even further through the addition of a pioneering innovation. With the new SMISSLINE TP system, components can now be plugged in or unplugged load-free without any risk from electrical current running through the body. The SMISSLINE TP pluggable socket system is completely finger-safe (IP0B) when devices are plugged in and unplugged, the system is always touch-proof. This means that SMISSLINE TP prevents any danger to personnel from switching arcs or accidental arcing. Even more flexible: make additions and changes during on going operation Pluggable devices can be added and changed quickly, safely and simply during ongoing operation. And this can be done without any need for personal protective equipment. This means that you benefit from more flexibility, savings on installation and maintenance and improved safety. SMISSLINE TP provides greater availability and operating safety than conventional systems. ABB Technical catalogue SMISSLINE TP CCC45059C003 0/3
Absolutely safe without protective equipment The SMISSLINE TP principle taken further The ingenious Click system Using the SMISSLINE TP system s unique SMISS CLICK function, five different protective devices can easily be plugged into one pluggable socket system with integrated busbars. In this way, the SMISSLINE system allows the uncomplicated, modular, flexible distribution of power up to a rated current of 50 A. Plugging in the devices quickly and without problems is essential for time-saving, cost-effective planning and execution. Current measurement system The CMS is a system for current measurement of electrical lines. The system consists of a Control Unit and sensors with different measurement ranges (0 A, 40 A, 80 A). The sensors measure alternating, direct and mixed currents (TRMS). The sensors get connected to the Control Unit by a flat cable. You can remotely query the measurement data via a RS485 interface (Modbus RTU). 0/4 CCC45059C003 ABB Technical catalogue SMISSLINE TP
SMISSLINE TP: The successful system is now finger-safe With SMISSLINE TP, fitters no longer require personal protective equipment, and so both the fitting and the operation/ expansion of the installation can now be carried out more safely, faster and thus more efficiently. The RANGE Miniature circuit-breaker -, -, 3- and 4-pole Residual-current circuit-breaker - and 4-pole Combined RCCB-MCB - and 4-pole Surge arrester type Switch disconnector Motor protection switch Busbar system, contact rails max. 00 A; incoming system with max. 50 A Wide range of accessories SMISSLINE TP at a glance Safe: load-free plugging in and unplugging possible under power Flexible: rapid replacement, easy expansion, mixed-pole layout possible Economical: saves time and space thanks to the plug-in technology Worth knowing: All SMISSLINE TP devices are downwardly compatible with the existing SMISSLINE pluggable socket system! ABB Technical catalogue SMISSLINE TP CCC45059C003 0/5
Pro E Power and pro E energy SMISSLINE TP in ABB enclosures Horizontal device arrangement Modules for a horizontal device arrangement for the SMISSLINE TP system The DIN rails are designed to be equipped with the SMISSLINE TP socket base rows. Vertical device arrangement Modules for a vertical device arrangement have cable laying grids for fastening the cables. The DIN rails are designed to be equipped with the SMISSLINE TP socket base rows; it is also possible to connect the SMISSLINE TP additional sockets (N/PE terminals). Front view horizontal modules Front view vertical modules Floor-standing cabinet fitted with modules for SMISSLINE TP devices and for pro M DIN rail mounting devices and for fuse switch disconnectors. 0/6 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Planning aid SMISSLINE TP socket base Socket base calculation with SMISSLINE TP Designer Software In Panel Design Configurator: SMISSLINE TP Designer The new SMISSLINE TP Designer is integrated into the base version of the Panel Design Configurator. This ensures that Panel Design Configurator now offers simple project planning and calculation for the SMISSLINE TP socket base system. The SMISSLINE TP Designer allows you to select and configure ABB SMISSLINE TP products in a graphical environment: Advantages at a glance: Full integration in Panel Design Configurator Cabinet and module selection in Panel Design Configurator is possible specifically for the SMISSLINE TP socket base Components are fitted to the socket base in a graphical environment Full range of SMISSLINE TP products for selection Configuration of accessories Automatic equipping Support for positioning the power supply Information on: Incoming and outgoing power Checking and display of space units, power and power loss Technical specifications for devices including price calculation (in Panel Design Configurator) Printing or export (in Panel Design Configurator) of parts lists, construction drawings or tender specifications Accessories dialogue box The combination of devices and additional components (such as auxiliary and signal contacts) is fully supported Automatic insertion of component combinations Automatic component selection for left/right positioning ABB Technical catalogue SMISSLINE TP CCC45059C003 0/7
Remote Power Panel Data Center Application Note Backup protection Based on backup and selectivity requirements a Molded Case Circuit Breaker (XT4) is used to protect the Sub-Distribution. The rating can go up to 50 A per MCCB if parallel incoming is used. The Backup protection complies with IEC/EN 60898- and IEC/EN 60947- and allows industrial use. With the integrated COM-Module all voltages, currents, power factors and status data is available through a Modbus RTU interface. Circuit Monitoring System Control Unit CMS-700 RPP s heart is the Control Unit CMS-700 which aggregates the current readings from the CMS and the Power Quality Values to create consumption data and generate alarms in case of system errors. In addition to the optional front door touch display CP65-WEB, a generic Modbus TCP and SNMP interface is supported. Typically this protocols are used to interface the data center infrastructure management system DCIM. Circuit Monitoring System open core and solid core sensors ABB s CMS is the most compact, neat and hassle-free branch circuit monitoring system available on the market. The sensors are mounted directly on the SMISSLINE Miniature Circuit Breakers and there is no need of conventional expensive and cumbersome cabling thanks to internal Modbus instead of typical Current Transformer star wiring. The new range of open core sensors helps to add branch monitoring into existing installations without the need to power-off they system. Touch proof system - SMISSLINE TP The world s first pluggable and touch proof socket system, SMISSLINE TP ensures that load-free devices and components can be safely snapped on and off under voltage without shutting down one single server. In addition maintenance can be done by instructed personnel without electrician s qualification. Moreover you can save 0 % space for the typical A/B distribution in a data center. Compared to a conventional build up time of 5 hours of an RPP like this SMISSLINE needs only 8h which allows another 45 % of time saving. Power Quality Analyzer The Power Quality Analyzer has dual function. First, it provides the voltage and power factor reference value to the PLC for calculating the effective power and energy values for the branch circuit. It allows the class III system reports according to DIN EN 6000--4 secondly, it provides the following data for the complete RPP: Active, reactive and apparent power Residual current monitoring Voltage quality (DIN EN 5060) Frequency and power factor Total harmonic distortion 0/8 CCC45059C003 ABB Technical catalogue SMISSLINE TP
XT4 50A Backup protection CP65-WEB Touch Display PLC AC500 or CMS-700 Circuit monitoring system Power quality analyzer SMISSLINE TP system ABB Technical catalogue SMISSLINE TP CCC45059C003 0/9
Six protection devices in one system 4 3 4 5 6 7 8 9 0 3 Incoming block 0/60 A Surge arrester 3 Control unit for Current measurement system 4 -pole residual current operated circuit breaker with overcurrent protection 5 4-pole residual current operated circuit breaker with overcurrent protection 0 Device latch Miniature circuit breaker 3 poles Miniature circuit breaker poles 3 4-pole residual current operated circuit breaker with overcurrent protection 4 Current measurement sensor 6 -pole residual current operated circuit breaker 7 4-pole residual current operated circuit breaker 8 Incoming block 63 A 9 Miniature circuit breaker pole 0/0 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Table of contents SMISSLINE TP Miniature circuit breaker S400 Miniature circuit breaker S400 M B / Miniature circuit breaker S400 M C /3 Miniature circuit breaker S400 M D /4 Miniature circuit breaker S400 M K /5 Miniature circuit breaker S400 M B /6 with protected neutral Miniature circuit breaker S400 M C /7 with protected neutral Miniature circuit breaker S400 M D /8 with protected neutral Miniature circuit breaker S400 M K /9 with protected neutral Miniature circuit breaker S400 UC /0 Miniature circuit breaker S400 UC, DC application / Residual current operated circuit breaker with over current protection (RCBO) -pole residual current opterated circuit breaker / with overcurrent protection FS40 4-pole residual current operated circuit breaker /3 with over current protection FS403 Residual current operated circuit breaker F404, F40 -pole and 4-pole residual current /4 operated circuit breaker F40, F404 Overcurrent arrester OVR404, switch disconnnector IS404 Surge arrester, Switch disconnector /5 High performance motor starter MS35 Adapter for motor starter MS35 /6 Accessory Auxiliary switch and signal contacts /7 Dummy, housing, Neutral disconnector, shunt trip /8 F4C-ARI motor operating devices /9 Current measurement system /0 Busbar system Starter pack Touch proof / 4 Sockets Touch proof /5 Incoming terminal block and components /6 Terminals for additional socket /7 8 Socket accessories /9 Combi module 3 A /30 3 A and 63 A universal adapters /3 3 Miscellaneous accessories /3 Busbars/selection table for sockets /33 ABB Technical catalogue SMISSLINE TP CCC45059C003 /
Series S400 M B Miniature circuit breaker Icn = 0 ka B according to EN 60898- Icn In Type ABB IT number EAN number Pack- Module Weight [ka] [A] name aging in 76 7 unit grams 0 4 S40M-B4 CCS5700R0045 00 4 0 0 0 6 S40M-B6 CCS5700R0065 00 0 0 0 8 S40M-B8 CCS5700R0085 00 84 0 0 0 0 S40M-B0 CCS5700R005 00 38 0 0 3/N 4/N 3 5 4 6 CCC40400Z000 CCC40403Z000 CCC4008Z000 CCC4500F0009 CCC45005F0009 CCC45009F0009 0 3 S40M-B3 CCS5700R035 00 45 0 0 0 6 S40M-B6 CCS5700R065 00 5 0 0 0 0 S40M-B0 CCS5700R005 00 69 0 0 0 5 S40M-B5 CCS5700R055 00 76 0 0 0 3 S40M-B3 CCS5700R035 00 83 0 0 0 40 S40M-B40 CCS5700R0405 00 90 0 0 0 50 S40M-B50 CCS5700R0505 00 306 0 0 0 63 S40M-B63 CCS5700R0635 00 33 0 0 0 4 S40M-B4 CCS5700R0045 00 986 5 0 6 S40M-B6 CCS5700R0065 00 993 5 0 8 S40M-B8 CCS5700R0085 00 848 5 0 0 S40M-B0 CCS5700R005 00 006 5 0 3 S40M-B3 CCS5700R035 00 03 5 0 6 S40M-B6 CCS5700R065 00 00 5 0 0 S40M-B0 CCS5700R005 00 037 5 0 5 S40M-B5 CCS5700R055 00 044 5 0 3 S40M-B3 CCS5700R035 00 05 5 0 40 S40M-B40 CCS5700R0405 00 068 5 0 50 S40M-B50 CCS5700R0505 00 075 5 0 63 S40M-B63 CCS5700R0635 00 08 5 0 4 S403M-B4 CCS57300R0045 00 754 3 3 3 0 6 S403M-B6 CCS57300R0065 00 76 3 3 3 0 8 S403M-B8 CCS57300R0085 00 8435 3 3 3 0 0 S403M-B0 CCS57300R005 00 778 3 3 3 0 3 S403M-B3 CCS57300R035 00 785 3 3 3 0 6 S403M-B6 CCS57300R065 00 79 3 3 3 0 0 S403M-B0 CCS57300R005 00 808 3 3 3 0 5 S403M-B5 CCS57300R055 00 85 3 3 3 0 3 S403M-B3 CCS57300R035 00 8 3 3 3 0 40 S403M-B40 CCS57300R0405 00 839 3 3 3 0 50 S403M-B50 CCS57300R0505 00 846 3 3 3 0 63 S403M-B63 CCS57300R0635 00 853 3 3 3 Ordering details for auxiliary switch and signal contacts on page /7 8 / CCC45059C003 ABB Technical catalogue SMISSLINE TP
Series S400 M C Miniature circuit breaker Icn = 0 ka, Icu = 5 5 ka C according to EN 60898- and IEC/EN 60947- Icu EN Icn EN In Type ABB IT number EAN Pack- Module Weight 60947-60898- name number aging in [ka] [ka] [A] 76 7 unit grams 5 0 0.5 S40M-C0.5 CCS5700R0984 00 30 0 0 5 0 S40M-C CCS5700R004 00 337 0 0 5 0.6 S40M-C.6 CCS5700R0974 00 344 0 0 5 0 S40M-C CCS5700R004 00 35 0 0 3/N 4/N 3 5 4 6 CCC40400Z000 CCC40403Z000 CCC4008Z000 CCC4500F0009 CCC45005F0009 CCC45009F0009 5 0 3 S40M-C3 CCS5700R0034 00 368 0 0 5 0 4 S40M-C4 CCS5700R0044 00 375 0 0 5 0 6 S40M-C6 CCS5700R0064 00 38 0 0 5 0 8 S40M-C8 CCS5700R0084 00 399 0 0 5 0 0 S40M-C0 CCS5700R004 00 405 0 0 5 0 3 S40M-C3 CCS5700R034 00 4 0 0 5 0 6 S40M-C6 CCS5700R064 00 49 0 0 5 0 0 S40M-C0 CCS5700R004 00 436 0 0 5 0 5 S40M-C5 CCS5700R054 00 443 0 0 5 0 3 S40M-C3 CCS5700R034 00 450 0 0 5 0 40 S40M-C40 CCS5700R0404 00 467 0 0 5 0 50 S40M-C50 CCS5700R0504 00 474 0 0 5 0 63 S40M-C63 CCS5700R0634 00 48 0 0 5 0 0.5 S40M-C0.5 CCS5700R0984 00 099 5 5 0 S40M-C CCS5700R004 00 05 5 5 0.6 S40M-C.6 CCS5700R0974 00 5 5 0 S40M-C CCS5700R004 00 9 5 5 0 3 S40M-C3 CCS5700R0034 00 36 5 5 0 4 S40M-C4 CCS5700R0044 00 43 5 5 0 6 S40M-C6 CCS5700R0064 00 50 5 5 0 8 S40M-C8 CCS5700R0084 00 67 5 5 0 0 S40M-C0 CCS5700R004 00 74 5 5 0 3 S40M-C3 CCS5700R034 00 8 5 5 0 6 S40M-C6 CCS5700R064 00 98 5 5 0 0 S40M-C0 CCS5700R004 00 04 5 5 0 5 S40M-C5 CCS5700R054 00 5 5 0 3 S40M-C3 CCS5700R034 00 8 5 5 0 40 S40M-C40 CCS5700R0404 00 35 5 5 0 50 S40M-C50 CCS5700R0504 00 4 5 5 0 63 S40M-C63 CCS5700R0634 00 59 5 5 0 0.5 S403M-C0.5 CCS57300R0984 00 860 3 3 3 5 0 S403M-C CCS57300R004 00 877 3 3 3 5 0.6 S403M-C.6 CCS57300R0974 00 884 3 3 3 5 0 S403M-C CCS57300R004 00 89 3 3 3 5 0 3 S403M-C3 CCS57300R0034 00 907 3 3 3 5 0 4 S403M-C4 CCS57300R0044 00 94 3 3 3 5 0 6 S403M-C6 CCS57300R0064 00 9 3 3 3 5 0 8 S403M-C8 CCS57300R0084 00 938 3 3 3 5 0 0 S403M-C0 CCS57300R004 00 945 3 3 3 5 0 3 S403M-C3 CCS57300R034 00 95 3 3 3 5 0 6 S403M-C6 CCS57300R064 00 969 3 3 3 5 0 0 S403M-C0 CCS57300R004 00 976 3 3 3 5 0 5 S403M-C5 CCS57300R054 00 983 3 3 3 5 0 3 S403M-C3 CCS57300R034 00 990 3 3 3 5 0 40 S403M-C40 CCS57300R0404 00 3003 3 3 3 5 0 50 S403M-C50 CCS57300R0504 00 300 3 3 3 5 0 63 S403M-C63 CCS57300R0634 00 307 3 3 3 ABB Technical catalogue SMISSLINE TP CCC45059C003 /3
Series S400 M D Miniature circuit breaker Icn = 0 ka D according to EN 60898- Icn In Type ABB IT number EAN number Pack- Module Weight [ka] [A] name aging in 76 7 unit grams 0 6 S40M-D6 CCS5700R006 00 498 0 0 0 8 S40M-D8 CCS5700R008 00 504 0 0 3/N 4/N 3 5 4 6 CCC40400Z000 CCC40403Z000 CCC4008Z000 CCC4500F0009 CCC45005F0009 CCC45009F0009 0 0 S40M-D0 CCS5700R00 00 5 0 0 0 3 S40M-D3 CCS5700R03 00 58 0 0 0 6 S40M-D6 CCS5700R06 00 535 0 0 0 0 S40M-D0 CCS5700R00 00 54 0 0 0 5 S40M-D5 CCS5700R05 00 559 0 0 0 3 S40M-D3 CCS5700R03 00 566 0 0 0 40 S40M-D40 CCS5700R040 00 573 0 0 0 50 S40M-D50 CCS5700R050 00 580 0 0 0 63 S40M-D63 CCS5700R063 00 597 0 0 0 6 S40M-D6 CCS5700R006 00 66 5 0 8 S40M-D8 CCS5700R008 00 73 5 0 0 S40M-D0 CCS5700R00 00 80 5 0 3 S40M-D3 CCS5700R03 00 97 5 0 6 S40M-D6 CCS5700R06 00 303 5 0 0 S40M-D0 CCS5700R00 00 30 5 0 5 S40M-D5 CCS5700R05 00 37 5 0 3 S40M-D3 CCS5700R03 00 334 5 0 40 S40M-D40 CCS5700R040 00 34 5 0 50 S40M-D50 CCS5700R050 00 358 5 0 63 S40M-D63 CCS5700R063 00 365 5 0 6 S403M-D6 CCS57300R006 00 3034 3 3 3 0 8 S403M-D8 CCS57300R008 00 304 3 3 3 0 0 S403M-D0 CCS57300R00 00 3058 3 3 3 0 3 S403M-D3 CCS57300R03 00 3065 3 3 3 0 6 S403M-D6 CCS57300R06 00 307 3 3 3 0 0 S403M-D0 CCS57300R00 00 3089 3 3 3 0 5 S403M-D5 CCS57300R05 00 3096 3 3 3 0 3 S403M-D3 CCS57300R03 00 30 3 3 3 0 40 S403M-D40 CCS57300R040 00 39 3 3 3 0 50 S403M-D50 CCS57300R050 00 36 3 3 3 0 63 S403M-D63 CCS57300R063 00 333 3 3 3 Ordering details for auxiliary switch and signal contacts on page /7 8 /4 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Series S400 M K Miniature circuit breaker (MCB) Icu = 5 5 ka K according to IEC/EN 60947- Icu In Type ABB IT number EAN number Pack- Module Weight [ka] [A] name aging in 76 7 unit grams 5 0.5 S40M-K0.5 CCS5700R057 00 603 0 0 5 S40M-K CCS5700R07 00 60 0 0 5.6 S40M-K.6 CCS5700R057 00 67 0 0 5 S40M-K CCS5700R077 00 634 0 0 3/N 4/N 3 5 4 6 CCC40400Z000 CCC40403Z000 CCC4008Z000 CCC4500F0009 CCC45005F0009 CCC45009F0009 5 3 S40M-K3 CCS5700R037 00 64 0 0 5 4 S40M-K4 CCS5700R0337 00 658 0 0 5 6 S40M-K6 CCS5700R0377 00 665 0 0 5 8 S40M-K8 CCS5700R0407 00 67 0 0 5 0 S40M-K0 CCS5700R047 00 689 0 0 5 3 S40M-K3 CCS5700R0447 00 696 0 0 5 6 S40M-K6 CCS5700R0467 00 70 0 0 5 0 S40M-K0 CCS5700R0487 00 79 0 0 5 5 S40M-K5 CCS5700R057 00 76 0 0 5 3 S40M-K3 CCS5700R0537 00 733 0 0 5 40 S40M-K40 CCS5700R0557 00 740 0 0 5 50 S40M-K50 CCS5700R0577 00 757 0 0 5 63 S40M-K63 CCS5700R0597 00 764 0 0 5 0.5 S40M-K0.5 CCS5700R057 00 37 5 5 S40M-K CCS5700R07 00 389 5 5.6 S40M-K.6 CCS5700R057 00 396 5 5 S40M-K CCS5700R077 00 40 5 5 3 S40M-K3 CCS5700R037 00 49 5 5 4 S40M-K4 CCS5700R0337 00 46 5 5 6 S40M-K6 CCS5700R0377 00 433 5 5 8 S40M-K8 CCS5700R0407 00 440 5 5 0 S40M-K0 CCS5700R047 00 457 5 5 3 S40M-K3 CCS5700R0447 00 464 5 5 6 S40M-K6 CCS5700R0467 00 47 5 5 0 S40M-K0 CCS5700R0487 00 488 5 5 5 S40M-K5 CCS5700R057 00 495 5 5 3 S40M-K3 CCS5700R0537 00 50 5 5 40 S40M-K40 CCS5700R0557 00 58 5 5 50 S40M-K50 CCS5700R0577 00 55 5 5 63 S40M-K63 CCS5700R0597 00 53 5 5 0.5 S403M-K0.5 CCS57300R057 00 340 3 3 3 5 S403M-K CCS57300R07 00 357 3 3 3 5.6 S403M-K.6 CCS57300R057 00 364 3 3 3 5 S403M-K CCS57300R077 00 37 3 3 3 5 3 S403M-K3 CCS57300R037 00 388 3 3 3 5 4 S403M-K4 CCS57300R0337 00 395 3 3 3 5 6 S403M-K6 CCS57300R0377 00 30 3 3 3 5 8 S403M-K8 CCS57300R0407 00 38 3 3 3 5 0 S403M-K0 CCS57300R047 00 35 3 3 3 5 3 S403M-K3 CCS57300R0447 00 33 3 3 3 5 6 S403M-K6 CCS57300R0467 00 349 3 3 3 5 0 S403M-K0 CCS57300R0487 00 356 3 3 3 5 5 S403M-K5 CCS57300R057 00 363 3 3 3 5 3 S403M-K3 CCS57300R0537 00 370 3 3 3 5 40 S403M-K40 CCS57300R0557 00 387 3 3 3 5 50 S403M-K50 CCS57300R0577 00 394 3 3 3 5 63 S403M-K63 CCS57300R0597 00 3300 3 3 3 ABB Technical catalogue SMISSLINE TP CCC45059C003 /5
S400 M B Miniature circuit breaker with protected neutral Icn = 0 ka B according to EN 60898- Icn In Type ABB IT number EAN number Pack- Module Weight [ka] [A] name aging in 76 7 unit grams 0 6 S40M-B6NP CCS5703R8065 00 337 5 0 8 S40M-B8NP CCS5703R8085 00 8473 5 3 4 3/N 4/N 5 7/N 6 8/N CCC4040Z000 CCC40403Z000 CCC4504F0009 CCC4508F0009 0 0 S40M-B0NP CCS5703R805 00 334 5 0 3 S40M-B3NP CCS5703R835 00 333 5 0 6 S40M-B6NP CCS5703R865 00 3348 5 0 0 S40M-B0NP CCS5703R805 00 3355 5 0 5 S40M-B5NP CCS5703R855 00 336 5 0 3 S40M-B3NP CCS5703R835 00 3379 5 0 40 S40M-B40NP CCS5703R8405 00 3386 5 0 50 S40M-B50NP CCS5703R8505 00 3393 5 0 63 S40M-B63NP CCS5703R8635 00 3409 5 0 6 S403M-B6NP CCS57303R8065 00 378 4 48 0 8 S403M-B8NP CCS57303R8085 00 850 4 48 0 0 S403M-B0NP CCS57303R805 00 3799 4 48 0 3 S403M-B3NP CCS57303R835 00 3805 4 48 0 6 S403M-B6NP CCS57303R865 00 38 4 48 0 0 S403M-B0NP CCS57303R805 00 389 4 48 0 5 S403M-B5NP CCS57303R855 00 3836 4 48 0 3 S403M-B3NP CCS57303R835 00 3843 4 48 0 40 S403M-B40NP CCS57303R8405 00 3850 4 48 0 50 S403M-B50NP CCS57303R8505 00 3867 4 48 0 63 S403M-B63NP CCS57303R8635 00 3874 4 48 Ordering details for auxiliary switch and signal contacts on page /7 8 The neutral is protected with 00% of the nominal value of the pole conductor /6 CCC45059C003 ABB Technical catalogue SMISSLINE TP
S400 M C MCB with protected neutral Icn = 0 ka, Icu = 5 5 ka C according to EN 60898- and IEC/EN 60947- Icu nach Icn nach In Type ABB IT Number EAN Pack- Module Weight 60947-60898- name number aging in [ka] [ka] [A] 76 7 unit grams 5 0 S40M-CNP CCS5703R804 00 8480 5 5 0 3 S40M-C3NP CCS5703R8034 00 8497 5 5 0 4 S40M-C4NP CCS5703R8044 00 8503 5 5 0 6 S40M-C6NP CCS5703R8064 00 346 5 3 4 3/N 4/N 5 7/N 6 8/N CCC4040Z000 CCC40403Z000 CCC4504F0009 CCC4508F0009 5 0 8 S40M-C8NP CCS5703R8084 00 343 5 5 0 0 S40M-C0NP CCS5703R804 00 3430 5 5 0 3 S40M-C3NP CCS5703R834 00 3447 5 5 0 6 S40M-C6NP CCS5703R864 00 3454 5 5 0 0 S40M-C0NP CCS5703R804 00 346 5 5 0 5 S40M-C5NP CCS5703R854 00 3478 5 5 0 3 S40M-C3NP CCS5703R834 00 3485 5 5 0 40 S40M-C40NP CCS5703R8404 00 349 5 5 0 50 S40M-C50NP CCS5703R8504 00 3508 5 5 0 63 S40M-C63NP CCS5703R8634 00 355 5 5 0 S403M-CNP CCS57303R804 00 857 4 48 5 0 3 S403M-C3NP CCS57303R8034 00 8534 4 48 5 0 4 S403M-C4NP CCS57303R8044 00 854 4 48 5 0 6 S403M-C6NP CCS57303R8064 00 388 4 48 5 0 8 S403M-C8NP CCS57303R8084 00 3898 4 48 5 0 0 S403M-C0NP CCS57303R804 00 3904 4 48 5 0 3 S403M-C3NP CCS57303R834 00 39 4 48 5 0 6 S403M-C6NP CCS57303R864 00 398 4 48 5 0 0 S403M-C0NP CCS57303R804 00 3935 4 48 5 0 5 S403M-C5NP CCS57303R854 00 394 4 48 5 0 3 S403M-C3NP CCS57303R834 00 3959 4 48 5 0 40 S403M-C40NP CCS57303R8404 00 3966 4 48 5 0 50 S403M-C50NP CCS57303R8504 00 3973 4 48 5 0 63 S403M-C63NP CCS57303R8634 00 3980 4 48 Ordering details for auxiliary switch and signal contacts on page /7 8 The neutral is protected with 00% of the nominal value of the pole conductor ABB Technical catalogue SMISSLINE TP CCC45059C003 /7
S400 M D Miniature circuit breaker with protected neutral Icn = 0 ka D according to EN 60898- Icn In Type ABB IT number EAN number Pack- Module Weight [ka] [A] name aging in 76 7 unit grams 0 0 S40M-D0NP CCS5703R80 00 35 5 0 3 S40M-D3NP CCS5703R83 00 3539 5 3/N 4/N CCC40403Z000 CCC4504F0009 CCC4508F0009 0 6 S40M-D6NP CCS5703R86 00 3546 5 0 0 S40M-D0NP CCS5703R80 00 3553 5 0 5 S40M-D5NP CCS5703R85 00 3560 5 0 3 S40M-D3NP CCS5703R83 00 3577 5 0 40 S40M-D40NP CCS5703R840 00 3584 5 0 50 S40M-D50NP CCS5703R850 00 359 5 0 63 S40M-D63NP CCS5703R863 00 3607 5 0 0 S403M-D0NP CCS57303R80 00 3997 4 48 0 3 S403M-D3NP CCS57303R83 00 4000 4 48 0 6 S403M-D6NP CCS57303R86 00 407 4 48 0 0 S403M-D0NP CCS57303R80 00 404 4 48 0 5 S403M-D5NP CCS57303R85 00 403 4 48 0 3 S403M-D3NP CCS57303R83 00 4048 4 48 0 40 S403M-D40NP CCS57303R840 00 4055 4 48 0 50 S403M-D50NP CCS57303R850 00 406 4 48 0 63 S403M-D63NP CCS57303R863 00 4079 4 48 Ordering details for auxiliary switch and signal contacts on page /7 8 The neutral is protected with 00% of the nominal value of the pole conductor 3 4 5 7/N 6 8/N CCC4040Z000 /8 CCC45059C003 ABB Technical catalogue SMISSLINE TP
S400 M K Miniature circuit breaker with protected neutral Icu = 5 5 ka K according to IEC/EN 60947- Icu In Type ABB IT number EAN number Pack- Module Weight [ka] [A] name aging in 76 7 unit grams 5 0.5 S40M-K0.5NP CCS5703R857 00 364 5 5 S40M-KNP CCS5703R87 00 36 5 5.6 S40M-K.6NP CCS5703R857 00 3638 5 3 4 3/N 4/N 5 7/N 6 8/N CCC4040Z000 CCC40403Z000 CCC4504F0009 CCC4508F0009 5 S40M-KNP CCS5703R877 00 3645 5 5 3 S40M-K3NP CCS5703R837 00 365 5 5 4 S40M-K4NP CCS5703R8337 00 3669 5 5 6 S40M-K6NP CCS5703R8377 00 3676 5 5 8 S40M-K8NP CCS5703R8407 00 3683 5 5 0 S40M-K0NP CCS5703R847 00 3690 5 5 3 S40M-K3NP CCS5703R8447 00 3706 5 5 6 S40M-K6NP CCS5703R8467 00 373 5 5 0 S40M-K0NP CCS5703R8487 00 370 5 5 5 S40M-K5NP CCS5703R857 00 3737 5 5 3 S40M-K3NP CCS5703R8537 00 3744 5 5 40 S40M-K40NP CCS5703R8557 00 375 5 5 50 S40M-K50NP CCS5703R8577 00 3768 5 5 63 S40M-K63NP CCS5703R8597 00 3775 5 5 0.5 S403M-K0.5NP CCS57303R857 00 4086 4 48 5 S403M-KNP CCS57303R87 00 4093 4 48 5.6 S403M-K.6NP CCS57303R857 00 409 4 48 5 S403M-KNP CCS57303R877 00 46 4 48 5 3 S403M-K3NP CCS57303R837 00 43 4 48 5 4 S403M-K4NP CCS57303R8337 00 430 4 48 5 6 S403M-K6NP CCS57303R8377 00 447 4 48 5 8 S403M-K8NP CCS57303R8407 00 454 4 48 5 0 S403M-K0NP CCS57303R847 00 46 4 48 5 3 S403M-K3NP CCS57303R8447 00 478 4 48 5 6 S403M-K6NP CCS57303R8467 00 485 4 48 5 0 S403M-K0NP CCS57303R8487 00 49 4 48 5 5 S403M-K5NP CCS57303R857 00 408 4 48 5 3 S403M-K3NP CCS57303R8537 00 45 4 48 5 40 S403M-K40NP CCS57303R8557 00 4 4 48 5 50 S403M-K50NP CCS57303R8577 00 439 4 48 5 63 S403M-K63NP CCS57303R8597 00 446 4 48 Ordering details for auxiliary switch and signal contacts on page /7 8 The neutral is protected with 00% of the nominal value of the pole conductor ABB Technical catalogue SMISSLINE TP CCC45059C003 /9
S400 M-UC application Miniature circuit breaker Icu = 0 5 ka C according to IEC/EN 60947- In Type ABB IT number EAN number Pack- Module Weight [A] name aging in 76 7 unit grams 0.5 S40M-UCC0.5 CCS5600R984 00 9746 0 45 S40M-UCC CCS5600R04 00 9753 0 45.6 S40M-UCC.6 CCS5600R974 00 9760 0 45 S40M-UCC CCS5600R04 00 9777 0 45 CCC4500F0009 3 S40M-UCC3 CCS5700R034 00 9784 0 45 4 S40M-UCC4 CCS5700R044 00 979 0 45 6 S40M-UCC6 CCS5700R064 00 9807 0 45 8 S40M-UCC8 CCS5700R084 00 984 0 45 P 0 V= 0 S40M-UCC0 CCS5700R04 00 98 0 45 3 S40M-UCC3 CCS5700R34 00 9838 0 45 6 S40M-UCC6 CCS5700R64 00 9845 0 45 0 S40M-UCC0 CCS5700R04 00 985 0 45 + Z00445.eps 5 S40M-UCC5 CCS5700R54 00 9869 0 45 3 S40M-UCC3 CCS5700R34 00 9876 0 45 40 S40M-UCC40 CCS5700R404 00 9883 0 45 50 S40M-UCC50 CCS5700R504 00 9890 0 45 63 S40M-UCC63 CCS5700R634 00 9906 0 45 0.5 S40M-UCC0.5 CCS5600R984 00 993 5 90 S40M-UCC CCS5600R04 00 990 5 90.6 S40M-UCC.6 CCS5600R974 00 9937 5 90 S40M-UCC CCS5600R04 00 9944 5 90 CCC45005F0009 3 S40M-UCC3 CCS5700R034 00 995 5 90 4 S40M-UCC4 CCS5700R044 00 9968 5 90 6 S40M-UCC6 CCS5700R064 00 9975 5 90 8 S40M-UCC8 CCS5700R084 00 998 5 90 P 440 V= 0 S40M-UCC0 CCS5700R04 00 9999 5 90 3 S40M-UCC3 CCS5700R34 0 000 5 90 3 6 S40M-UCC6 CCS5700R64 0 008 5 90 0 S40M-UCC0 CCS5700R04 0 005 5 90 + 4 Z00446.eps 5 S40M-UCC5 CCS5700R54 0 003 5 90 3 S40M-UCC3 CCS5700R34 0 0049 5 90 40 S40M-UCC40 CCS5700R404 0 0056 5 90 50 S40M-UCC50 CCS5700R504 0 0063 5 90 63 S40M-UCC63 CCS5700R634 0 0070 5 90 Ordering details for auxiliary switch and signal contacts on page /7 8 Connection diagram, single-pole (max. 0 V=) S40M-UCC Load Connection diagram, two-pole (max. 440 V=) S40M-UCC Load 3 4 Mains Z00003.eps Mains Z00004.eps /0 CCC45059C003 ABB Technical catalogue SMISSLINE TP
S400 M-UC, DC application Miniature circuit breaker Icu = 0 5 ka Z according to IEC/EN 60947- In Type ABB IT number EAN number Pack- Module Weight [A] name aging in 76 7 unit grams 0.5 S40M-UCZ0.5 CCS5600R988 0 0087 0 0 S40M-UCZ CCS5600R08 0 0094 0 0.6 S40M-UCZ.6 CCS5600R978 0 000 0 0 CCC4500F0009 S40M-UCZ CCS5600R08 0 07 0 0 3 S40M-UCZ3 CCS5700R038 0 04 0 0 4 S40M-UCZ4 CCS5700R048 0 03 0 0 6 S40M-UCZ6 CCS5700R068 0 048 0 0 8 S40M-UCZ8 CCS5700R088 0 055 0 0 P 0 V= 0 S40M-UCZ0 CCS5700R08 0 06 0 0 3 S40M-UCZ3 CCS5700R38 0 079 0 0 6 S40M-UCZ6 CCS5700R68 0 086 0 0 0 S40M-UCZ0 CCS5700R08 0 093 0 0 + Z00445.eps 5 S40M-UCZ5 CCS5700R58 0 009 0 0 3 S40M-UCZ3 CCS5700R38 0 06 0 0 40 S40M-UCZ40 CCS5700R408 0 03 0 0 50 S40M-UCZ50 CCS5700R508 0 030 0 0 63 S40M-UCZ63 CCS5700R638 0 047 0 0 0.5 S40M-UCZ0.5 CCS5600R988 0 054 0 S40M-UCZ CCS5600R08 0 06 0.6 S40M-UCZ.6 CCS5600R978 0 078 0 S40M-UCZ CCS5600R08 0 085 0 CCC45005F0009 3 S40M-UCZ3 CCS5700R038 0 09 0 4 S40M-UCZ4 CCS5700R048 0 0308 0 6 S40M-UCZ6 CCS5700R068 0 035 0 8 S40M-UCZ8 CCS5700R088 0 03 0 0 S40M-UCZ0 CCS5700R08 0 0339 0 P 440 V= 3 S40M-UCZ3 CCS5700R38 0 0346 0 3 6 S40M-UCZ6 CCS5700R68 0 0353 0 0 S40M-UCZ0 CCS5700R08 0 0360 0 + 4 Z00446.eps 5 S40M-UCZ5 CCS5700R58 0 0377 0 3 S40M-UCZ3 CCS5700R38 0 0384 0 40 S40M-UCZ40 CCS5700R408 0 039 0 50 S40M-UCZ50 CCS5700R508 0 0407 0 63 S40M-UCZ63 CCS5700R638 0 044 0 Ordering details for auxiliary switch and signal contacts on page /7 8 Connection diagram, single-pole (max. 0 V=) S40M-UCZ Load Connection diagram, two-pole (max. 440 V=) S40M-UCZ Load 3 4 Mains Z00003.eps Mains Z00004.eps ABB Technical catalogue SMISSLINE TP CCC45059C003 /
FS40 LN Residual current operated circuit breaker with overcurrent protection B, 6 ka according to EN 6009- I n In Icn Type ABB IT number EAN Pack- Module Weight [ma] [A] [ka] name number aging in 76 7 unit grams 30 3 6 FS40 E-B 3/0.03 CCL56E035 00 8558 50 30 6 6 FS40 E-B 6/0.03 CCL56E065 00 8565 50 30 0 6 FS40 E-B 0/0.03 CCL56E005 00 969 50 30 5 6 FS40 E-B 5/0.03 CCL56E055 00 9708 50 30 3 6 FS40 E-B 3/0.03 CCL56E035 00 975 50 / 3/4/N / 4/3/N CCC40407Z000 CCC4503F000 C, 6 ka according to EN 6009-30 3 6 FS40 E-C 3/0.03 CCL56E034 00 857 50 30 6 6 FS40 E-C 6/0.03 CCL56E064 00 8589 50 30 0 6 FS40 E-C 0/0.03 CCL560E004 00 4574 50 30 5 6 FS40 E-C 5/0.03 CCL560E054 00 458 50 30 3 6 FS40 E-C 3/0.03 CCL560E034 00 4598 50 C, 6 ka 00 ma according to EN 6009-00 0 6 FS40 E-C0/0. CCL560E004 4 083 40 00 5 6 FS40 E-C5/0. CCL560E054 4 485 40 00 3 6 FS40 E-C3/0. CCL560E034 40 0446 40 B, 0 ka according to EN 6009-30 0 0 FS40 M-B 0/0.03 CCL560E005 00 9685 50 30 3 0 FS40 M-B 3/0.03 CCL560E035 00 4505 50 30 6 0 FS40 M-B 6/0.03 CCL560E065 00 45 50 C, 0 ka according to EN 6009-0 6 0 FS40 M-C 6/0.0 CCL56000E0064 40 6493 50 30 6 0 FS40 M-C 6/0.03 CCL5600E0064 40 6905 50 00 6 0 FS40 M-C6/0. CCL560E0064 4 4534 40 30 0 0 FS40 M-C 0/0.03 CCL560E004 00 4543 50 00 0 0 FS40 M-C0/0. CCL560E004 4 37 40 0 3 0 FS40 M-C 3/0.0 CCL5600E034 00 459 50 30 3 0 FS40 M-C 3/0.03 CCL560E034 00 4550 50 0 6 0 FS40 M-C 6/0.0 CCL5600E064 00 4536 50 30 6 0 FS40 M-C 6/0.03 CCL560E064 00 4567 50 00 6 0 FS40 M-C6/0. CCL560E064 4 68 40 C, 6 ka and 0 ka according to EN 6009- short time delayed (APR) 30 0 0 FS40 M K-C 0/0.03 CCL5630E004 40 403 50 30 3 0 FS40 M K-C 3/0.03 CCL5630E034 00 4604 50 30 6 0 FS40 M K-C 6/0.03 CCL5630E064 00 46 50 30 0 6 FS40 E K-C 0/0.03 CCL5630E004 00 468 50 30 5 6 FS40 E K-C 5/0.03 CCL5630E054 00 4635 50 30 3 6 FS40 E K-C 3/0.03 CCL5630E034 00 464 50 Ordering details for auxiliary switch and signal contacts on page /7 8 / CCC45059C003 ABB Technical catalogue SMISSLINE TP
FS403 3LN Residual current operated circuit breaker with overcurrent protection B, 0 ka according to EN 6009- / 3/4 5/6 7/8/N / 4/3 6/5 8/7/N CCC45099Z000 CCC45500F0003 new new new I n In Icn Type ABB IT number EAN Pack- Module Weight [ma] [A] [ka] name number aging in 76 7 unit grams 30 6 0 FS403M-B6/0.03 CCL5640E0065 43 4434 4 45 30 0 0 FS403M-B0/0.03 CCL5640E005 40 76 4 45 30 3 0 FS403M-B3/0.03 CCL5640E035 40 769 4 45 30 6 0 FS403M-B6/0.03 CCL5640E065 40 7636 4 45 30 0 0 FS403M-B0/0.03 CCL5630E005 44 576 4 45 30 5 0 FS403M-B5/0.03 CCL5630E055 44 590 4 45 30 3 0 FS403M-B3/0.03 CCL5630E035 44 63 4 45 C, 6 ka according to EN 6009-30 6 6 FS403E-C6/0.03 CCL564E0064 4 94 4 45 30 0 6 FS403E-C0/0.03 CCL564E004 43 4489 4 45 30 3 6 FS403E-C3/0.03 CCL564E034 43 459 4 45 30 6 6 FS403E-C6/0.03 CCL564E064 43 460 4 45 30 0 6 FS403E-C0/0.03 CCL564E003 40 9609 4 45 30 5 6 FS403E-C5/0.03 CCL564E054 40 8770 4 45 30 3 6 FS403E-C3/0.03 CCL564E034 40 8787 4 45 C, 0 ka according to EN 6009-30 6 0 FS403M-C6/0.03 CCL5640E0064 4 97 4 45 30 0 0 FS403M-C0/0.03 CCL5640E004 40 7674 4 45 30 3 0 FS403M-C3/0.03 CCL5640E034 40 768 4 45 30 6 0 FS403M-C6/0.03 CCL5640E064 40 7698 4 45 new new new 30 0 0 FS403M-C0/0.03 CCL5630E004 44 569 4 45 30 5 0 FS403M-C5/0.03 CCL5630E054 44 583 4 45 30 3 0 FS403M-C3/0.03 CCL5630E034 44 606 4 45 C, 0 ka according to EN 6009-00 6 6 FS403M-C6/0. CCL564E0064 4 457 4 45 00 0 0 FS403M-C0/0. CCL564E004 4 450 4 45 00 3 0 FS403M-C3/0. CCL5630E034 44 60 4 45 00 6 0 FS403M-C6/0. CCL5640E064 4 009 4 45 new new new 00 0 0 FS403M-C0/0. CCL5630E004 44 637 4 45 00 5 0 FS403M-C5/0. CCL5630E054 44 644 4 45 00 3 0 FS403M-C3/0. CCL5630E034 44 65 4 45 ABB Technical catalogue SMISSLINE TP CCC45059C003 /3
F40, F404 - and 4-pole residual current operated circuit breaker -pole residual current operated circuit breaker, series F40 (RCCB) CCC450F000 IΔn In Type ABB IT number EAN Pack- Module Weight name number aging in ma A 76 7 unit grams 0 5 F40 A 5/0.0 CCF5500E050 00 440 50 / 3/4/N / 4/3/N CCC40406Z000 30 5 F40 A 5/0.03 CCF550E050 00 4437 50 30 40 F40 A 40/0.03 CCF550E0400 00 4444 50 00 40 F40 A 40/0. CCF5500E0400 00 94 50 -pole short time delayed residual current operated circuit breaker, series F40 K 30 40 F40 A-K 40/0.03 CCF5530E0400 00 448 50 4-pole residual current operated circuit breaker, series F404 (RCCB) 30 5 F404 A 5/0.03 CCF5440E050 00 453 4 430 / 3/4 5/6 7/8/N / 4/3 6/5 8/7/N CCC40408Z000 CCC4505F000 30 40 F404 A 40/0.03 CCF5440E0400 00 460 4 430 00 40 F404 A 40/0. CCF5440E0400 00 477 4 430 300 40 F404 A 40/0.3 CCF54430E0400 00 484 4 430 30 63 F404 A 63/0.03 CCF5440E0630 00 49 4 430 00 63 F404 A 63/0. CCF5440E0630 00 4307 4 430 300 63 F404 A 63/0.3 CCF54430E0630 00 434 4 430 500 63 F404 A 63/0.5 CCF60057E0630 40 566 4 430 4-pole short time delayed residual current operated circuit breaker, series F404 K (RCCB) 30 40 F404 A-K 40/0.03 CCF54430E0400 00 43 4 430 00 40 F404 A-K 40/0. CCF54430E0400 00 4338 4 430 30 63 F404 A-K 63/0.03 CCF54430E0630 00 4345 4 430 4-pole selective residual current operated circuit breaker, series F404 S (RCCB) 00 63 F404 A-S 63/0. CCF5440E0630 00 435 4 430 300 63 F404 A-S 63/0.3 CCF54430E0630 00 4369 4 430 4-pole residual current operated circuit breaker, special design 6 /3 Hz, series F404 LF (RCCB) 30 63 F404 A-LF 63/0.03 CCF5440E063 00 4376 4 430 300 63 F404 A-LF 63/0.3 CCF54430E063 00 4383 4 430 Ordering details for auxiliary switch and signal contacts on page /6 7 /4 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Surge arrester, Switch disconnector CCC4545F000 Surge arrester OVR404 Isn (8/0 µs) Type ABB IT number EAN number Pack- Module Weight [ka] name aging in unit grams 0 OVR404 4L 40-75 P TS QS CCF606000R000 76 7 45 549 4 470 0 OVR404 3N 40-75 P TS QS CCF60600R000 76 7 45 5507 4 450 0 OVR404 4L 40-440 P TS QS CCR606000A0003 4 OVR404 4L CCC4590Z000 CCC4590Z000 OVR404 3LN CCC459Z000 CCC459Z000 CCC4508F000 Switch disconnector IS404 In Type ABB IT number EAN number Pack- Module Weight [A] name aging in 76 7 unit grams 63 IS404 63 CCF54460E0630 00 4390 4 380 Ordering details for auxiliary switch and signal contacts on page /6 7 / 3/4 5/6 7/8/N / 4/3 6/5 8/7/N CCC404030Z000 CCC4569F000 Cover switch disconnector IS404/F404 The Cover ist for the Incoming terminals Type ABB IT number EAN number E number Pack- Weight name < aging in 76 7 unit grams ZFI30 CCA60560R000 4 045 550 50 503 ABB Technical catalogue SMISSLINE TP CCC45059C003 /5
Adapter for motor starter MS6, MS3, MS35 4060 CCC4568F000 CCC45600F000 CCC4560F000 CCC45776F000 CCC45764F000 Adapter for MS6, MS3 Designation Type ABB IT number EAN Pack- Module Weight name number aging in 76 7 unit grams Adapter MS6/3 ZMS930 CCA850R000 4 4597,5 30 L3 wire bottom feed Adapter MS6/3 ZMS93 CCA85R000 4 4580,5 6 L3LALB wire bottom feed Adapter MS6/3 ZMS93 CCA854R000 4 4573,5 30 L3 wire top feed Adapter MS6/3 ZMS933 CCA856R000 4 4566,5 6 L3LALB wire top feed Adapter MS6/3 ZMS934 CCA85R000 4 4559,5 34 empty Intermediate ZMS935 CCA866R000 4 44 0,5 7 piece 9 mm Adapter MS6/3 ZMS937 CCA855R000 4 466,5 58 L3LA wire top feed Adapter MS6/3 ZMS936 CCA85R000 4 469,5 58 L3LA wire bottom feed CCC45F000 Adapter plate for MS35 contact to busbars with plug contacts Type ABB IT number EAN number Pack- Weight name aging in 76 7 unit grams 3L ZMS95 CCF0087R000 00 5 30 L, N(0A) ZMS96 CCF0088R000 00 30 L, N(0A) ZMS97 CCF0089R000 00 39 30 L3, N(0A) ZMS98 CCF0080R000 00 46 30 L (reversible) ZMS99 CCF0060R000 00 53 30 405 Auxiliary switch and signal contacts, connection support Contact pin, short ABB IT number EAN number Pack- Weight aging in 76 7 unit grams for power supply CCF00794R000 00 956 via auxiliary busbars ZMS 95 MS35 / ZLS 5.., In max. 3 A ZMS 96 MS35, In max. 0 A ZMS 97 MS35, In max. 0 A ZMS 98 MS35, In max. 0 A ZMS 99 MS35, In max. 0 A /6 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Auxiliary switch and signal contacts MCB S400, RCCB F404, RCCB F40, RCBO FS40 3 4 CCC4509Z000 CCC4509F000 CCC450F000 CCC457F000 The auxiliary switch and signal contacts are supplied with one contacting piece. The signal contact collective alarm are supplied with two contacting pieces. Auxiliary switch Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams for left side mounting on MCB S400, RCBO FS40, FS403 NO and NC HK400-L CCS500900R008 00 090 0 0.5 45 NO HK4000-L CCF0R000 0 83 0 0.5 40 NC HK4000-L CCF04R000 0 90 0 0.5 40 for right side mounting on RCB F404/40, MCB S400 and IS404 NO and NC HK400-R CCS500900R04 00 869 0 0.5 45 NO HK4000-R CCF03R000 0 06 0 0.5 40 NC HK4000-R CCF05R000 0 3 0 0.5 40 3 4 97 05 98 06 CCC4503Z000 CCC4509Z000 CCC456F000 3 4 CCC4509Z000 Signal contacts Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams for left side mounting on MCB S400, RCBO FS40, FS403 NO and NC SK400-L CCS500900R00 00 0934 0 0.5 45 NO SK4000-L CCF06R000 0 07 0 0.5 40 NC SK4000-L CCF064R000 0 4 0 0.5 40 for right side mounting on RCB F404/40, MCB S400 and IS404 NO and NC SK400-R CCS500900R05 00 866 0 0.5 45 NO SK4000-R CCF063R000 0 0 0.5 40 NC SK4000-R CCF065R000 0 38 0 0.5 40 Signal contact collective alarm and auxiliary contact Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams for left side mounting 97 98 CCC45030Z000 CCC45F000 97 98 CCC45030Z000 CCC45F000 NO SK4000-L SA CCS500900R04 00 7964 0 0.5 45 NO HK4000-L SA CCF0R000 40 790 0 0.5 45 for right side mounting NO SK4000-R SA CCS500900R06 00 8633 0 0.5 45 NO HK4000-R SA CCF03R000 40 799 0 0.5 45 Collective alarm, signal contact contacts the auxiliary busbars LA, LB A cost-effective collective alarm solution can be implemented without additional wiring by using this arrangement. CCC45079F000 ABB Technical catalogue SMISSLINE TP CCC45059C003 /7
Dummy, housing, Neutral disconnector, shunt trip C C C3 C4 CCC4508Z000 CCC45034F000 CCC45033F000 Connection support dummy housing for left or right side mounting on MCB S400, RCCB F40, RCCB F404, RCBO FS40 Connection Type ABB IT number EAN number Pack- Module Weight support name aging in 76 7 unit grams AS400 CCS500900R05 00 0958 0 0.5 45 Dummy housing Compensation to 8 mm ZLS93 CCS500900R06 00 0965 0 0.5 35 CCC456F000 CCC4563F000 Contacting pieces for auxiliary switch and signal contacts Contacting piece for ZLS63 CCS500900R07 00 097 Pack 00 HK/SK LA, LB contains Pack contains 00 items 00 items Contacting piece for ZLS635 CC50307R07 00 965 Pack 0 HK/SK LA, LB contains Pack contains 0 items 0 items Contact Pin ZLS633 CCS500900R00 00 8640 Pack contains 0 items Neutral disconnector On the load side terminal two separate conductors can be clamped CCC45035F000 CCC45036F000 Neutral disconnector NT40 63 CCS500900R00 00 0859 0 0.5 45 9 mm Neutral disconnector NT40 63 CCS500900R00 00 084 0 58 8 mm Compensation to 8 mm ZLS78 CCS400900R00 00 470 Bag 0.5 5 for NT40 63 contains 5 items C C CCC40404F000 C C CCC457Z000 Shunt trip Function: remote opening of the device when a voltage is applied. Suitable for MCBs S400 series. Rated voltage Type ABB IT number EAN number Pack- Module Weight name aging in grams 80 54 unit 60 V AC/DC S C-A CDS 00 909 R000 57 099 50 0 45 V AC/DC, 0 50 V DC S C-A CDS 00 909 R000 57 005 50 Orders for this two types can be done over DESTO /8 CCC45059C003 ABB Technical catalogue SMISSLINE TP
F4C-ARI motor operating devices CCC4549F000 Motor operating devices for residual current circuit breakers F404 5 63 A Supply voltage 30 V AC; 48 V DC integrated auxiliary contact Type name ABB IT number EAN number Packaging Modul Weight F4C-CM CSF04986R003 8054998730 66 unit in grams For Supply voltage 30V it is needed to use a safety transformer TS6/ (CSM640R40R08). Motor operating auto-reclosing unit for residual current circuit breakers F404 5 63A Supply voltage 30 V AC; 48 V DC integrated auxiliary contact Type name ABB IT number EAN number Packaging Modul Weight unit in grams F4C-ARI CSF04987R003 805499863 66 For Supply voltage 30 V it is needed to use a safety transformer TS6/ (CSM640R40R08). Safety transformer Type name ABB IT number EAN number Packaging Weight unit in grams TS6/ CSM640R08 8054368908 355 ABB Technical catalogue SMISSLINE TP CCC45059C003 /9
Current measurement system For more Information and additional products see catalogue CCC48003C00. CCC4800F000 CCC48008F000 Sensors 8 mm for pro M compact and SMISSLINE Description Type designation ABB IT number EAN number Pack- Weight aging in grams 80 A TRMS CMS-00PS CCA88000R000 767490 40 A TRMS CMS-0PS CCA8800R000 767499 0 A TRMS CMS-0PS CCA8800R000 767496 CCC4805F000 Control Unit Modbus RTU CMS- 600 CCA880000R000 76748700 53 CCC48006F000 Accessories Flat cable m CMS-800 CCA88048R000 7674933 7 Connector set 35 pc. CMS-80 CCA88045R000 7674940 4 /0 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Starter pack Touch proof 3L CCC45689F000 Starter Pack 3L: L, L, L3 inclusive socket end piece Solutions Busbars length Busbars length Type ABB IT EAN Pack- Weight available incl. Socket name number number aging in end piece mm mm 76 7 grams 8 PLE 3L 364 30 ZLS905E8-3L CCA833R000 4654 530 0 PLE 3L 40 357 ZLS905E0-3L CCA8300R000 433 637 PLE 3L 437 393 ZLS905E-3L CCA830R000 4355 693 4 PLE 3L 473 49 ZLS905E4-3L CCA8304R000 4379 749 6 PLE 3L 509 465 ZLS905E6-3L CCA8306R000 4393 83 8 PLE 3L 545 50 ZLS905E8-3L CCA8308R000 4345 848 30 PLE 3L 58 537 ZLS905E30-3L CCA830R000 43439 933 3 PLE 3L 67 573 ZLS905E3-3L CCA83R000 43453 98 34 PLE 3L 653 609 ZLS905E34-3L CCA834R000 43477 044 36 PLE 3L 689 645 ZLS905E36-3L CCA836R000 4349 00 38 PLE 3L 75 68 ZLS905E38-3L CCA838R000 4354 56 40 PLE 3L 76 77 ZLS905E40-3L CCA830R000 43538 4 PLE 3L 797 753 ZLS905E4-3L CCA83R000 4355 76 44 PLE 3L 833 789 ZLS905E44-3L CCA834R000 43576 33 46 PLE 3L 869 85 ZLS905E46-3L CCA836R000 43590 388 48 PLE 3L 905 86 ZLS905E48-3L CCA838R000 4363 444 50 PLE 3L 94 897 ZLS905E50-3L CCA8330R000 43637 508 5 PLE 3L 977 933 ZLS905E5-3L CCA833R000 4365 564 54 PLE 3L 03 969 ZLS905E54-3L CCA8334R000 43675 60 56 PLE 3L 049 005 ZLS905E56-3L CCA8336R000 43699 675 58 PLE 3L 058 04 ZLS905E58-3L CCA8338R000 437 739 60 PLE 3L 078 ZLS905E60-3L CCA8340R000 43736 795 6 PLE 3L 58 4 ZLS905E6-3L CCA834R000 43750 85 64 PLE 3L 94 50 ZLS905E64-3L CCA8344R000 43774 907 66 PLE 3L 30 86 ZLS905E66-3L CCA8346R000 43798 97 68 PLE 3L 66 ZLS905E68-3L CCA8348R000 438 07 70 PLE 3L 30 58 ZLS905E70-3L CCA8350R000 43835 083 7 PLE 3L 338 94 ZLS905E7-3L CCA835R000 43859 39 74 PLE 3L 374 330 ZLS905E74-3L CCA8354R000 43873 03 76 PLE 3L 40 366 ZLS905E76-3L CCA8356R000 43897 69 78 PLE 3L 446 40 ZLS905E78-3L CCA8358R000 4390 34 80 PLE 3L 48 438 ZLS905E80-3L CCA8360R000 43934 370 ABB Technical catalogue SMISSLINE TP CCC45059C003 /
Starter pack Touch proof 3LN CCC45690F000 Starter Pack 3LN: L, L, L3, N inclusive socket end piece Solutions Busbars length Busbars length Type ABB IT EAN Pack- Weight available incl. Socket name number number aging in end piece mm mm 76 7 grams 8 PLE 3LN 364 30 ZLS905E8-3LN CCA8334R000 465 65 0 PLE 3LN 40 357 ZLS905E0-3LN CCA830R000 4348 74 PLE 3LN 437 393 ZLS905E-3LN CCA8303R000 436 789 4 PLE 3LN 473 49 ZLS905E4-3LN CCA8305R000 4386 800 6 PLE 3LN 509 465 ZLS905E6-3LN CCA8307R000 43408 96 8 PLE 3LN 545 50 ZLS905E8-3LN CCA8309R000 434 970 30 PLE 3LN 58 537 ZLS905E30-3LN CCA83R000 43446 046 3 PLE 3LN 67 573 ZLS905E3-3LN CCA833R000 43460 0 34 PLE 3LN 653 609 ZLS905E34-3LN CCA835R000 43484 93 36 PLE 3LN 689 645 ZLS905E36-3LN CCA837R000 43507 57 38 PLE 3LN 75 68 ZLS905E38-3LN CCA839R000 435 3 40 PLE 3LN 76 77 ZLS905E40-3LN CCA83R000 43545 387 4 PLE 3LN 797 753 ZLS905E4-3LN CCA833R000 43569 459 44 PLE 3LN 833 789 ZLS905E44-3LN CCA835R000 43583 54 46 PLE 3LN 869 85 ZLS905E46-3LN CCA837R000 43606 589 48 PLE 3LN 905 86 ZLS905E48-3LN CCA839R000 4360 653 50 PLE 3LN 94 897 ZLS905E50-3LN CCA833R000 43644 76 5 PLE 3LN 977 933 ZLS905E5-3LN CCA8333R000 43668 79 54 PLE 3LN 03 969 ZLS905E54-3LN CCA8335R000 4368 855 56 PLE 3LN 049 005 ZLS905E56-3LN CCA8337R000 43705 90 58 PLE 3LN 058 04 ZLS905E58-3LN CCA8339R000 4379 99 60 PLE 3LN 078 ZLS905E60-3LN CCA834R000 43743 057 6 PLE 3LN 58 4 ZLS905E6-3LN CCA8343R000 43767 64 PLE 3LN 94 50 ZLS905E64-3LN CCA8345R000 4378 86 66 PLE 3LN 30 86 ZLS905E66-3LN CCA8347R000 43804 59 68 PLE 3LN 66 ZLS905E68-3LN CCA8349R000 4388 34 70 PLE 3LN 30 58 ZLS905E70-3LN CCA835R000 4384 388 7 PLE 3LN 338 94 ZLS905E7-3LN CCA8353R000 43866 453 74 PLE 3LN 374 330 ZLS905E74-3LN CCA8355R000 43880 56 76 PLE 3LN 40 366 ZLS905E76-3LN CCA8357R000 43903 590 78 PLE 3LN 446 40 ZLS905E78-3LN CCA8359R000 4397 655 80 PLE 3LN 48 438 ZLS905E80-3LN CCA836R000 4394 79 / CCC45059C003 ABB Technical catalogue SMISSLINE TP
Starter pack Touch proof 3L LA LB CCC4569F000 Starter Pack 3LLALB: L, L, L3, LA, LB inclusive socket end piece Solutions Busbars length Busbars length Type ABB IT EAN Pack- Weight available incl. Socket name number number aging in end piece mm 76 7 grams 8 PLE 3L LA LB 364 30 ZLS905E8-3LLALB CCA8333R000 46538 586 0 PLE 3L LA LB 40 357 ZLS905E0-3LLALB CCA836R000 46904 753 PLE 3L LA LB 437 393 ZLS905E-3LLALB CCA8364R000 469 8 4PLE 3L LA LB 473 49 ZLS905E4-3LLALB CCA8366R000 4698 835 6PLE 3L LA LB 509 465 ZLS905E6-3LLALB CCA8368R000 46935 964 8PLE 3L LA LB 545 50 ZLS905E8-3LLALB CCA8370R000 4694 0 30PLE 3L LA LB 58 537 ZLS905E30-3LLALB CCA837R000 46959 07 3PLE 3L LA LB 67 573 ZLS905E3-3LLALB CCA8374R000 46966 67 34PLE 3L LA LB 653 609 ZLS905E34-3LLALB CCA8376R000 46973 4 36PLE 3L LA LB 689 645 ZLS905E36-3LLALB CCA8378R000 46980 30 38PLE 3L LA LB 75 68 ZLS905E38-3LLALB CCA8380R000 46997 377 40PLE 3L LA LB 76 77 ZLS905E40-3LLALB CCA838R000 47000 445 4PLE 3L LA LB 797 753 ZLS905E4-3LLALB CCA8384R000 4707 50 44PLE 3L LA LB 833 789 ZLS905E44-3LLALB CCA8386R000 4704 588 46PLE 3L LA LB 869 85 ZLS905E46-3LLALB CCA8388R000 4703 656 48PLE 3L LA LB 905 86 ZLS905E48-3LLALB CCA8390R000 47048 73 50PLE 3L LA LB 94 897 ZLS905E50-3LLALB CCA839R000 47055 799 5PLE 3L LA LB 977 933 ZLS905E5-3LLALB CCA8394R000 4706 866 54PLE 3L LA LB 03 969 ZLS905E54-3LLALB CCA8396R000 47079 934 56PLE 3L LA LB 049 005 ZLS905E56-3LLALB CCA8398R000 47086 00 58PLE 3L LA LB 058 04 ZLS905E58-3LLALB CCA8300R000 47093 077 60PLE 3L LA LB 078 ZLS905E60-3LLALB CCA830R000 4709 44 6PLE 3L LA LB 58 4 ZLS905E6-3LLALB CCA8304R000 476 64PLE 3L LA LB 94 50 ZLS905E64-3LLALB CCA8306R000 473 79 66PLE 3L LA LB 30 86 ZLS905E66-3LLALB CCA8308R000 4730 355 68PLE 3L LA LB 66 ZLS905E68-3LLALB CCA830R000 4747 43 70 PLE 3L LA LB 30 58 ZLS905E70-3LLALB CCA83R000 4754 490 7PLE 3L LA LB 338 94 ZLS905E7-3LLALB CCA834R000 476 558 74PLE 3L LA LB 374 330 ZLS905E74-3LLALB CCA836R000 4778 633 76PLE 3L LA LB 40 366 ZLS905E76-3LLALB CCA838R000 4785 70 78PLE 3L LA LB 446 40 ZLS905E78-3LLALB CCA830R000 479 768 80PLE 3L LA LB 48 438 ZLS905E80-3LLALB CCA83R000 4708 836 ABB Technical catalogue SMISSLINE TP CCC45059C003 /3
Starter pack Touch proof 3LN LA LB CCC4569F000 Starter Pack 3LNLALB: L, L, L3, N, LA, LB inclusive socket end piece Solutions Busbars length Busbars length Type ABB IT EAN Pack- Weight available incl. Socket name number number aging in end piece mm 76 7 grams 8 PLE 3LN LA LB 364 30 ZLS905E8-3LNLALB CCA8335R000 46545 67 0 PLE 3LN LA LB 40 357 ZLS905E0-3LNLALB CCA8363R000 475 84 PLE 3LN LA LB 437 393 ZLS905E-3LNLALB CCA8365R000 47 97 4PLE 3LN LA LB 473 49 ZLS905E4-3LNLALB CCA8367R000 4739 939 6PLE 3LN LA LB 509 465 ZLS905E6-3LNLALB CCA8369R000 4746 078 8PLE 3LN LA LB 545 50 ZLS905E8-3LNLALB CCA837R000 4753 33 30PLE 3LN LA LB 58 537 ZLS905E30-3LNLALB CCA8373R000 4760 38 3PLE 3LN LA LB 67 573 ZLS905E3-3LNLALB CCA8375R000 4777 306 34PLE 3LN LA LB 653 609 ZLS905E34-3LNLALB CCA8377R000 4784 39 36PLE 3LN LA LB 689 645 ZLS905E36-3LNLALB CCA8379R000 479 467 38PLE 3LN LA LB 75 68 ZLS905E38-3LNLALB CCA838R000 47307 543 40PLE 3LN LA LB 76 77 ZLS905E40-3LNLALB CCA8383R000 4734 69 4PLE 3LN LA LB 797 753 ZLS905E4-3LNLALB CCA8385R000 473 704 44PLE 3LN LA LB 833 789 ZLS905E44-3LNLALB CCA8387R000 47338 780 46PLE 3LN LA LB 869 85 ZLS905E46-3LNLALB CCA8389R000 47345 856 48PLE 3LN LA LB 905 86 ZLS905E48-3LNLALB CCA839R000 4735 933 50PLE 3LN LA LB 94 897 ZLS905E50-3LNLALB CCA8393R000 47369 07 5PLE 3LN LA LB 977 933 ZLS905E5-3LNLALB CCA8395R000 47376 093 54PLE 3LN LA LB 03 969 ZLS905E54-3LNLALB CCA8397R000 47383 69 56PLE 3LN LA LB 049 005 ZLS905E56-3LNLALB CCA8399R000 47390 46 58PLE 3LN LA LB 058 04 ZLS905E58-3LNLALB CCA830R000 47406 330 60PLE 3LN LA LB 078 ZLS905E60-3LNLALB CCA8303R000 4743 406 6PLE 3LN LA LB 58 4 ZLS905E6-3LNLALB CCA8305R000 47505 48 64PLE 3LN LA LB 94 50 ZLS905E64-3LNLALB CCA8307R000 497 559 66PLE 3LN LA LB 30 86 ZLS905E66-3LNLALB CCA8309R000 4740 643 68PLE 3LN LA LB 66 ZLS905E68-3LNLALB CCA83R000 47437 79 70 PLE 3LN LA LB 30 58 ZLS905E70-3LNLALB CCA833R000 47444 796 7PLE 3LN LA LB 338 94 ZLS905E7-3LNLALB CCA835R000 4745 87 74PLE 3LN LA LB 374 330 ZLS905E74-3LNLALB CCA837R000 47468 956 76PLE 3LN LA LB 40 366 ZLS905E76-3LNLALB CCA839R000 47475 303 78PLE 3LN LA LB 446 40 ZLS905E78-3LNLALB CCA83R000 4748 309 80PLE 3LN LA LB 48 438 ZLS905E80-3LNLALB CCA833R000 47499 385 /4 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Sockets Touch proof CCC45695F000 CCC45586F000 Socket base Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams 8-module socket ZLS908 CCA83030R000 4 3965 0 8 9 Length 44 mm (includes base and cover) 6-module socket ZLS906 CCA83035R000 4 3958 0 6 7 Length 08 mm (includes base and cover) CCC459F000 Busbars for the sockets Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams 00 A busbar plated, ZLS00 CCF0077R000 00 570 0 0 640 0 x 3 mm, for L, L, L3, N and PE Delivery length 979 mm 40 A auxiliary busbar plated, ZLS0 CCF00773R000 00 579 0 0 40 5 x mm, for LA und LB Delivery length 979 mm CCC4568F000 CCC45683F000 Socket end piece Type ABB IT number- EAN number Pack- Module name aging 76 7 unit To prevent displacement ZLS90 CCA8307R000 4 567 of sockets and busbars ( pieces, left and right) ABB Technical catalogue SMISSLINE TP CCC45059C003 /5
Incoming terminal block and components CCC45406F000 Incoming terminal block 8 mm, 63 A,5 mm to 5 mm max. wire contact above contact bottom Type ABB EAN Pack- Module Weight name IT number number aging in 76 7 unit grams L, L3 63 A ZLS60 CCA05305R000 0 57 90 L, N 63 A ZLS6 CCA05306R000 0 589 90 LA, LB 6 A ZLS6 CCA05307R000 0 596 90 CCC450400F00 CCC45057F000 CCC4505800F00 Incoming terminal component 0 mm to 95 mm Version Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams Feeder component L ZLS5 CCV6750R000 050 539 0 Feeder component L ZLS5 CCV6750R000 050 536 0 Feeder component L3 ZLS53 CCV67503R000 050 5333 0 Feeder component N ZLS50 CCV67500R000 050 5340 0 Feeder component N additional socket ZLS954 CCV67508R000 4 4404 00 Feeder component PE additional socket ZLS955 CCV67509R000 4 44 00 CCC45040F000 CCC45073F000 Incoming terminal blocks 6 mm to 50 mm ( x 5 mm ) + x 0 mm (LA, LB) Standard incoming terminal block, complete with main terminals and cover, construction height 50 mm Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams 50 mm ( x 5 mm ) 3LN left ZLS4 CCF0596R000 00 986 4 80 50 mm ( x 5 mm ) 3LN right ZLS4R CCA805R000 05 076 4 80 50 mm ( x 5 mm ) + x 0 mm 3LNAB (auxiliary busbars) ZLS4LAB CCA8054R000 005 45 4 00 50 mm ( x 5 mm ) 3L left ZLS5 CCF0597R000 00 983 4 50 50 mm ( x 5 mm ) 3L right ZLS5R CCA8053R000 05 0733 4 50 50 mm ( x 5 mm ) + x 0 mm 3LAB (auxiliary busbars) ZLS5LAB CCA8055R000 005 40 4 70 Cover for standard incoming terminal block ZLS35 CCA80069R000 00 543 4 37 Additional parts for standard incoming terminal block Auxiliary terminal max. items 0 mm ZLS33 CCF00786R000 00 95 0 (for auxiliary bus bars LA, LB) N terminal for incom. ZLS3 CCF00785R000 00 944 30 term. block Incoming terminal block, low, complete with main terminals, construction height 36 mm 50 mm ( x 5 mm ), 3LN ZLS8 CCF0500R000 00 9854 4 80 50 mm ( x 5 mm ), 3L ZLS9 CCF050R000 00 986 4 50 /6 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Additonal socket touch proof Additional socket The additional socket can easily be fitted onto the socket base to accomodate the external N and/or PE busbars. This enables neutral connections to be made where single-pole miniature circuit breakers are used with unswitched neutral. Neutral terminals are clipped onto the additional socket and can be used as detachable neutral connections. One N busbar and/or one PE busbar can be fitted. Each socket base can be equipped with an additional socket. CCC45780F000 CCC45778F000 Additional socket for external N and PE busbars Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams 8-module socket ZLS98 CCA83630R000 4 0444 0 8 34 (suitable for 8-module socket) 6-module socket ZLS96 CCA83635R000 4 0437 0 6 6 (suitable for 6-module socket) ABB Technical catalogue SMISSLINE TP CCC45059C003 /7
Terminals TP, additional socket N terminals and PE terminals Corresponding N terminals (blue) or PE terminals (yellow-green) are available for the power supply and the outgoing conduetors of the external N and PE busbars for cross sections. The terminals are fitted with label holders whitch can be used wiht the marking adapter or the selfadhesive marking label (Phoenix Contact type Clipline UC-TM): Connection for the terminals ZLS9, 95 0,75 mm up to 0 mm litz wire with ferrule mm up to 0 mm strand x,5 mm or x,5 mm allowed, all other combinatins it is only allowed with one wire ZLS93, 96 6 mm up to 35 mm wire with ferrule, max. wire ZLS954, 955 50 mm up to 95 mm wire with ferrule, max. wire CCC45783F000 CCC4579F000 N terminal for additional socket light blue, for external busbars Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams N 0 mm ZLS9 CCA83460R000 4 090 0 0.5 N 35 mm ZLS93 CCA83470R000 4 304 0 30 N 95 mm ZLS954 CCV67508R000 4 4404 00 CCC45784F000 CCC45793F000 PE terminal for additional socket yellow-green, for external busbars PE 0 mm ZLS95 CCA8346R000 4 3 0 0.5 PE 35 mm ZLS96 CCA8347R000 4 38 0 30 PE 95 mm ZLS955 CCV67509R000 4 44 00 CCC4578F000 CCC45785F000 CCC45786F000 CCC45795F000 CCC45794F000 Red/orange terminals for additional socket Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams 0 mm ZLS9/ CCA83475R000 4 335 0 0.5 Red 0 mm ZLS95/ CCA83476R000 4 359 0 0.5 Orange 35 mm ZLS93/ CCA83465R000 4 34 0 30 Red 35 mm ZLS96/ CCA83466R000 4 366 0 30 Orange Insulator block The dark grey insulator block isolates the interrupted bus bar ends from one another and simultaneously marks the disconnection point externally. Insulator block for additional socket Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams ZLS97 CCA83463R000 4 373 0 0.5 6 /8 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Socket accessories CCC45048F000 Intermediate piece Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams light grey, ZLS75 CCS500900R08 00 0989 00 fills shock-proof empty module spaces 8 mm bag containing 5 items Compensation piece ZLS78 CCS400900R00 00 470 70 to 8 mm for NT 9 mm bag containing 5 items CCC45666F000 Busbar insulator dark grey, ZLS938 CCA056R000 4 805 0 for isolation and spacing of separate busbar sections, 8 mm CCC4505F000 Busbar cover electrically protected ZLS00 CCF0076R000 00 5603 95 covering of main and auxiliary busbars. The 4 modules cover can be divided. Suitable to accept extension adapter ZLS 0 4x8 mm bag containing 5 items Add-on adapter 8 mm wide, ZLS0 CCF00763R000 00 560 0 can be plugged on busbar cover ZLS00. To mount conventional DIN devices with 45 mm cap size. bag containing 0 items 407 Mounting rail adapter Height compensation ZLS74 CCA8008R000 00 963 0 3.5 mm, to equalize the installation depth of standard DIN-rail mounted devices alongside the SMISSLINE plug-in system. CCC4534F000 Locking device Padlock adapter 3 mm SA GJF0903R000 00 4833 3 Bag containing 0 items Padlock SA GJF0903R000 00 4857 0 ABB Technical catalogue SMISSLINE TP CCC45059C003 /9
Combi module 3 A (ln), 6 A (la, lb) MS6/3 + AF contactor Combi module for MS6/MS3 and AF contactor Designation Type ABB IT number EAN Pack- Module Weight name number aging in 76 7 unit grams Combi module L,L,L3 ZMS3-3L CCA8500R000 4464,5 95 top feed Combi module L,L,L3 ZMS3-3LA CCA850R000 44634,5 98 top feed Combi module L,L<,L3 ZMS3-3LB CCA8504R000 4467,5 98 top feed Combi module L,L,L3 ZMS3-3LAB CCA8506R000 4460,5 0 top feed Combi module ZMS37 CCA8508R000 44603,5 75 without plug-in contacts Connection pin to mont combi E0-SPV CCC70375R000 4480 Set à 30 moduls together Intermediate ZMS935 CCA866R000 4 44 0,5 6 piece 9 mm Adapter for manual motor starter MS6 and MS3 Designation Type ABB IT number EAN Pack- Module Weight name number aging in 76 7 unit grams Adapter MS6/3 ZMS930 CCA850R000 4 4597,5 30 L3 wire bottom feed Adapter MS6/3 ZMS93 CCA85R000 4 4580,5 6 L3LALB wire bottom feed Adapter MS6/3 ZMS936 CCA85R000 4 469,5 58 L3LA wire bottom feed Adapter MS6/3 ZMS93 CCA854R000 4 4573,5 30 L3 wire top feed Adapter MS6/3 ZMS933 CCA856R000 4 4566,5 6 L3LALB wire top feed Top feed Bottom feed CCC45776F000 Adapter MS6/3 ZMS937 CCA855R000 4 466,5 58 L3LA wire top feed Adapter MS6/3 ZMS934 CCA85R000 4 4559,5 34 empty Intermediate ZMS935 CCA866R000 4 44 0,5 6 piece 9 mm The 9 mm wide additional housing is need to use when an unequal number (, 3, 5, ) of combi modules or adapter are plugged on the socket. This is needed to fill the space into a full module (8 mm). The 9 mm wide additional housing can be also use when on one side of the manual motor starter an auxiliary contact is mounted. The order codes of manual motor starter and the contactors auf in the ABB catalogue DOC SBC0055C00 or in the local ABB catalogue. /30 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Universal adapters 3 A and 63 A CCC45308F000 CCC453F000 Universal adapters 3 A and 63 A, Adapter for use EN/IEC 6439-6 or UL508 Designation Type ABB IT number EAN number Pack- Module Weight name aging in 76 7 unit grams Adapter 3A L/L/L3 wire top ZLS970 CCA8055R000 44 4563 0 0 L/L/L3 wire bottom ZLS97 CCA8055R000 44 4570 0 0 N wire top ZLS970N CCA80553R000 44 4587 0 0 N wire bottom ZLS97N CCA80554R000 44 4570 0 0 Adapter 63A L/L/L3 wire top ZLS97 CCA80555R000 44 4709 0 4 L/L/L3 wire bottom ZLS973 CCA80556R000 44 476 0 4 N wire top ZLS97N CCA80557R000 44 4808 0 4 N wire bottom ZLS973N CCA80558R000 44 4730 0 4 Adapter 3A with 300mm wire CCC45348F000 CCC453F000 CCC4539F000 CCC45394F000 CCC45349F000 CCC4535F000 L/L/L3 wire top ZLS970300 CCA80559R000 44 4747 0 6 L/L/L3 wire bottom ZLS97300 CCA80560R000 44 4754 0 6 N wire top ZLS970N300 CCA8056R000 44 476 0 6 N wire bottom ZLS97N300 CCA8056R000 44 4778 0 6 Adapter 63A with 300mm wire L/L/L3 wire top ZLS97300 CCA80563R000 44 4785 0 37 L/L/L3 wire bottom ZLS973300 CCA80564R000 44 479 0 37 N wire top ZLS97N300 CCA80565R000 44 4808 0 37 N wire bottom ZLS973N300 CCA80566R000 44 485 0 37 Universaldapter 5 A and 45 A for use UL489 Adapter 5A UL489, adapter can be only used together with ABB Pro M MCB S00 UL489 L/L/L3 wire top ZLS970UL CCA33700R000 44 48 0 L/L/L3 wire bottom ZLS97UL CCA3370R000 44 4839 0 Adapter 45A UL489, adapter can be only used together with ABB Pro M MCB S00 UL489 L/L/L3 wire top ZLS97UL CCA33704R000 44 4860 0 5 L/L/L3 wire bottom ZLS973UL CCA33705R000 44 4877 0 5 Accessory Dummy housing ZLS964 CCA80550R000 44 4556 0 Connector for multi-pole adapter Bag with 30 pcs. E0-SPV CCC70375R000 4480 Set of 30 pcs. 50 connectors are needed to connect adapters ABB Technical catalogue SMISSLINE TP CCC45059C003 /3
Busbars 40 A and 00 A 40 A and 00 A busbars / selection table for sockets Order data ABB EAN ZLS908 ZLS906 Module Length Busbar Order date ABB EAN busbar IT number number incl. length busbar IT number number 00 A 767 end piece in mm 40 A 767 ZLS0E6 CCF80058R000 006778 6 48 03 ZLS03E6 CCF8008R000 007966 ZLS0E8 CCF80059R000 006983 8 86 39 ZLS03E8 CCF8009R000 00878 ZLS0E CCF80060R000 006 56 ZLS03E CCF8000R000 007409 ZLS0E4 CCF8006R000 00630 4 9 47 ZLS03E4 CCF800R000 007508 ZLS0E6 CCF8006R000 006334 6 38 83 ZLS03E6 CCF800R000 0075 ZLS0E8 CCF80063R000 006358 3 8 364 39 ZLS03E8 CCF8003R000 007546 ZLS0E0 CCF80064R000 00637 0 40 355 ZLS03E0 CCF8004R000 007560 ZLS0E CCF80065R000 006396 437 39 ZLS03E CCF8005R000 007584 ZLS0E4 CCF800666R000 00649 3 4 473 47 ZLS03E4 CCF8006R000 007607 ZLS0E6 CCF80067R000 006433 3 6 509 463 ZLS03E6 CCF8007R000 0076 ZLS0E8 CCF80068R000 006457 8 545 499 ZLS03E8 CCF8008R000 007645 ZLS0E30 CCF80069R000 00647 3 30 58 535 ZLS03E30 CCF8009R000 007669 ZLS0E3 CCF80070R000 006495 4 3 67 57 ZLS03E3 CCF80030R000 007683 ZLS0E34 CCF8007R000 00658 3 34 653 607 ZLS03E34 CCF8003R000 007706 ZLS0E36 CCF8007R000 00653 3 36 689 643 ZLS03E36 CCF8003R000 00770 ZLS0E38 CCF80073R000 006556 4 38 75 679 ZLS03E38 CCF80033R000 007744 ZLS0E40 CCF80074R000 006570 5 40 76 75 ZLS03E40 CCF80034R000 007768 ZLS0E4 CCF80075R000 006594 3 3 4 797 75 ZLS03E4 CCF80035R000 00778 ZLS0E44 CCF80076R000 00667 4 44 833 787 ZLS03E44 CCF80036R000 007805 ZLS0E46 CCF80077R000 00663 5 46 869 83 ZLS03E46 CCF80037R000 00789 ZLS0E48 CCF80078R000 006655 6 48 905 859 ZLS03E48 CCF80038R000 007843 ZLS0E50 CCF80079R000 006679 4 3 50 94 895 ZLS03E50 CCF80039R000 007867 ZLS0E5 CCF80080R000 006693 5 5 977 93 ZLS03E5 CCF80040R000 00788 ZLS0E54 CCF8008R000 00676 6 54 03 968 ZLS03E54 CCF8004R000 007904 ZLS0E56 CCF8008R000 006730 7 56 049 004 ZLS03E56 CCF8004R000 00798 ZLS0E58 CCF80083R000 006754 5 3 58 085 040 ZLS03E58 CCF80043R000 00794 ZLS0E60 CCF80084R000 006785 6 60 076 ZLS03E60 CCF80044R000 007973 ZLS0E6 CCF80085R000 006808 7 6 58 ZLS03E6 CCF80045R000 007997 ZLS0E64 CCF80086R000 0068 8 64 94 48 ZLS03E64 CCF80046R000 00807 ZLS0E66 CCF80087R000 006846 6 3 66 30 84 ZLS03E66 CCF80047R000 00803 ZLS0E68 CCF80088R000 006860 7 68 66 0 ZLS03E68 CCF80048R000 008055 ZLS0E70 CCF80089R000 006884 8 70 30 56 ZLS03E70 CCF80049R000 008079 ZLS0E7 CCF80090R000 006907 9 7 338 9 ZLS03E7 CCF80050R000 008093 ZLS0E74 CCF8009R000 0069 7 3 74 374 38 ZLS03E74 CCF8005R000 0086 ZLS0E76 CCF8009R000 006945 8 76 40 364 ZLS03E76 CCF8005R000 00830 ZLS0E78 CCF80093R000 006969 9 78 446 400 ZLS03E78 CCF80053R000 00854 ZLS0E80 CCF80094R000 006990 0 80 48 436 ZLS03E80 CCF80054R000 00885 ZLS0E8 CCF80095R000 00700 8 3 8 58 47 ZLS03E8 CCF80055R000 00808 ZLS0E84 CCF80096R000 007034 9 84 554 508 ZLS03E84 CCF80056R000 008 ZLS0E86 CCF80097R000 007058 0 86 590 544 ZLS03E86 CCF80057R000 00846 ZLS0E88 CCF80098R000 00707 88 66 580 ZLS03E88 CCF80058R000 00860 ZLS0E90 CCF80099R000 007096 9 3 90 66 66 ZLS03E90 CCF80059R000 00884 ZLS0E9 CCF80000R000 0079 0 9 698 65 ZLS03E9 CCF80060R000 008307 ZLS0E94 CCF8000R000 00733 94 734 688 ZLS03E94 CCF8006R000 0083 ZLS0E96 CCF8000R000 00757 96 770 74 ZLS03E96 CCF8006R000 008345 ZLS0E98 CCF80003R000 0077 0 3 98 806 760 ZLS03E98 CCF80063R000 008369 ZLS0E00 CCF80004R000 006006 00 843 796 ZLS03E00 CCF80064R000 00795 ZLS0E0 CCF80005R000 00600 0 879 83 ZLS03E0 CCF80065R000 0078 ZLS0E04 CCF80006R000 006044 3 04 95 868 ZLS03E04 CCF80066R000 0073 ZLS0E06 CCF80007R000 006068 3 06 95 904 ZLS03E06 CCF80067R000 00756 ZLS0E08 CCF80008R000 00608 08 987 940 ZLS03E08 CCF80068R000 00770 Planning for the incorporation of feeder block and spare places should be taken into account. The total lengths given above were calculated taking socket spacings and tolerances into account. For this reason, the indicated busbar length is not necessarily a multiple of 8 mm ( Module). /3 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Table of contents Technical data Busbar system Overview devices with a busbar system / Socket/additional socket/busbars /4 Incoming terminal block/incoming terminal components /5 7 Power supply /8 Busbar system accessories /9 Combi module /0 Definitions / Technical data overview / 3 Miniature circuit breaker S400 Technical data overview /4 6 Trip characteristics applications /7 Trip characteristics, trip behaviour /8 Diagram of let through energy I t /0 Power Supply: overload and short circuit protection / Technical data: back-up and selectivity /3 Back-up protection with fuses, S800 /4 Back-up protection with Tmax and XT /5 Influence of ambient temperature /6 7 Protection of circuits with fluorescent lamps, /8 DC applications with S400M DC applications with S400UC /9 CMS Current Measurement System Bus bar system /57 66 The design of the plug-in socket system SMISSLINE TP ensures that load-free devices and components can be snapped on and off under voltage without the need for additional personal protective equipment to protect against electrical hazards. This is certified by the German Berufsgenossenschaft and electro suisse (for other countries please follow to the national regulations and standards). Residuel current operated circuit breaker F40, F404 Properties, Technical data /30 35 Residual current operated circuit breaker RCBO FS40 Properties, Technical data /36 37 Residual current operated circuit breaker RCBO FS403 Internal resistances and power losses /38 Derating, Back up /39 Limitation of specific let-through energy I t, peak current Ip /40 Switch disconnector IS404 Description, Technical data overview /4 Overcurrent arrester OVR404 Technical data overview /4 47 Auxiliary switches and signal contacts /48 Accessory mounting options /49 Auxiliary switches and signal contacts wiring variants /50 Auxiliary switches and signal contacts left/right mounting /5 Motor operating devices for S404 Specific features for F4C-CM /5 Technical specifications /53 Specific features for F4C-ARI /54 Technical specifications /55 Shunt trip for S400 Technical data /56 ABB Technical catalogue SMISSLINE TP CCC45059C003 /
Overview devices with a busbar system 30 3 5 4 8 6 5 9 CCC4580F000 7 7 Supply terminal Incoming terminal block with a max. current rating of 60 A 50 mm ( x 5 mm ) + x 0 mm (LA, LB) 3 Cover for incoming terminal block 4 Supply cable 5 Residual current operated circuit breaker with overcurrent protection RCBO FS40 and FS403 6 Residual-current circuit breaker F404 7 Miniature circuit breaker S40 M 8 Signal contact 9 Plug contacts 0 DIN adapter Spare way cover Device latch 3 Busbar L3 or DC +, 4 Busbar L or DC +, 5 Busbar L or DC +, 6 Busbar N 7 Cover for socket 8 Sockets 9 Auxiliary busbar LA / CCC45059C003 ABB Technical catalogue SMISSLINE TP
Overview of busbar system 7 8 9 30 8 3 9 0 6 3 4 5 3 0 Auxiliary busbar LB 3 4 0 CCC45800F000 Output circuits Busbar isolator 3 Socket end piece on left and right 6 5 4 Incoming terminal component, centre power supply 00 A, maximum 95 mm 5 Combi module with a current rating of 3 A 6 Adapter for DIN rail components 7 N- and PE Terminals, red and orange Terminals for d.c. Application 8 Busbar PE, additional socket 9 Busbar N, additional socket 30 Additional socket ABB Technical catalogue SMISSLINE TP CCC45059C003 /3
Socket/additional socket/busbars CCC45645F000 Socket bases ZLS906, ZLS908 The SMISSLINE socket system is a totally new kind of assembly and connection technology for the construction of distributions. Besides the classic method of snapping the devices onto 35-mm mounting rails, the new family of devices can be directly attached to the socket bases with integrated busbars. The time-consuming process of connecting up the supply is thereby no longer needed. In addition, in the event of rearrangement or expansion, the replacement of devices in existing systems is made significantly easier. CCC45696F000 The socket sections and the wide range of accessories make it possible to plan with the capability for expansion and to construct distribution systems of any desired size in a short period of time. 6- and 8-module sockets are installed either by screwing them onto any flat surface or by snapping them onto a 35 mm DIN mounting rail. Lateral movement or detachment of the sockets again is possible before final fixing. In order to determine the required socket length, the space necessary for the devices required the incoming terminal block and any reserve spaces needed must be determined. CCC45693F000 Snap mounting Pull down the slide with a screwdriver until it latches (socket can be moved). Press on front of slid: Fixed position (Sockets fixed) CCC45694F000 The key features System of any desired length (even number of poles) Integrated busbars Simple device change Long-term planning and problem free extension possible Significant time savings during assembly and connection CCC459F000 Busbars for the sockets and additional socket ZLS00 The busbars of size 0 x 3 mm can be loaded with currents up to 00 A. They are plated for perfect contact wiith the devices plug-in contacts. The maximum available busbar length is 979 mm. The same busbar type is used, regardless whether it is fitted in the socket (L, L, L3, N) or in the additional socket (N, PE). The busbars are inserted in to the socket from the front. Auxiliary busbars for the socket ZLS0 The 5 x mm auxiliary busbars are intended for a common power supply of auxiliary switches and signal contacts. They are also plated and their max. delivery length is 979 mm. Like the main busbars, the auxiliary busbars are inserted in holders LA and LB from the front. Of course, only on auxiliary busbar can be fitted. /4 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Incoming terminal block/incoming terminal components CCC45406F000 CCC45407F000 Incoming terminal blocks ZLS60 to 6 Compact terminal block with the construction width of 8 mm for poles. The maximum rated current is 63 A for L, L, L3N and 6 A for LA, LB. General The incoming terminal block is used to connect cables directly to the busbars. The terminals act directly on the busbars and therefore fix the incoming terminal block. Removable terminal tops permit the connection of continous conductrors (risers) white horizontal or vertical cable entry is also possible. Instead of using the incoming terminal block, the power supply can also be realized via a device (e.g. residual current operated circuit breaker, miniature circuit breaker or switch disconnector). CCC45073F000 Incoming terminal blocks ZLS4, 5 A standard incoming terminal block whose cover provides protection against accidental contact. Construction height 50 mm. The base plate can be fitted with a maximum of 4 main terminals L, L, L3 and N for the busbars, and auxiliary termiinals LA and LB for the auxiliary busbars. Incoming terminal blocks, low ZLS8, 9 Incoming terminal block with construction height of 36 mm. 4504F000 Incoming terminal component ZLS50 to 55 The incoming terminal component, with an installation width of 36 mm is available as a singlepole component for the line conductors L, L, L3 and as neutral. The terminals act directly on the busbars and thereby fix the incoming terminal component. The incoming terminal component, L, L, L3 and N can be combined to meet specific needs. A maximum cable crosssection of 95 mm can be connected to the incoming terminal component. ABB Technical catalogue SMISSLINE TP CCC45059C003 /5
Incoming terminal block/incoming terminal components 63 A, 00 A,5 A, 60 A and 00 A Incoming Power supply in centre, maximum 60 A. A maximum of 00 A is permitted on either side. A total of 60 A must not be exceeded. Incoming maximum 63 A. CCC4535F000 CCC453F000 CCC458F000 CCC459F000 Power supply left or right, maximum 00 A. 5 A (max. 35 C Ambient air temperature for 5 A continuously) Power supply left or right, maximum 00 A. 5 A (max. 35 C Ambient air temperature for 5 A continuously) CCC4534F000 Incoming terminal component, in centre, maximum 00 A. But on each side not more than 00 A. /6 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Incoming terminal block 50 A parallel Incoming Feed centrally maximum 50 A. The cables in the connections must have the same length. Incoming terminal blocks ZLS4 or ZLS5. max. 5 A max. 5 A CCC4575Z000 Feed per side maximum 5 A, 50 A total. The cables in the connections must have the same length. max. 5 A max. 5 A CCC4574Z000 ABB Technical catalogue SMISSLINE TP CCC45059C003 /7
Power supply CCC457F000 Indirect supply via residual current operated circuit breaker (RCCB) (or switch disconnector) The supply cable is connected at the top of the RCCB. This supply variant gives the busbars and therefore all subsequent devices RCCB protection. If several RCCB groups are planned, the busbars should be separated and spaced using the dark grey busbar insulator ZLS938. Attention must then be paid to the regulations governing protection of the residual current circuit breaker by subsequent miniature circuit breakers. The supply can also be fed in through the switch disconnector. CCC453F000 Direct supply to residual current operated circuit breaker (or switch disconnector) Instead of using the incoming terminal block, the power can also be supplied via a device In this case, the supply cable is connected to the lower terminal of the device. The residual current operated circuit breaker or switch disconnector can be supplied with 63 A regardless of its rated current, since the plug-in connection arrangement of the device is suitable for this amount of current. For current in excess of 63 A, the incoming terminal block or the incoming terminal component should be used. CCC4530F000 Supply of auxiliary busbars LA and LB The two auxiliary busbars LA and LB can be supplied using the additional terminal ZLS 33 via a incoming terminal block. The maximum operating current of the auxiliary busbars is 40 A. CCC4534F000 Incoming block for two auxiliary busbars LA, LB The pluggable incoming block is especially for the two auxiliary busbars LA, LB. The maximum rated current is 6 A. /8 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Busbar system accessories Socket end piece ZLS90 To prevent displacement of sockets and busbars (particulary when installed vertically) end pieces can be fitted at the start and finish of each row of sockets. These simultaneously ensure electrically protected covering of the busbar end faces and mechanical fixing of the sockets oh the mounting rail. CCC45048F000 CCC45094F000 CCC45666F000 CCC45096F000 Intermediate piece ZLS75 The light grey intermediate piece matches the device profile and fills empty module spaces. Busbar insulator ZLS938 The dark grey busbar insulator electrically isolates the separated busbar ends from each other (e.g. when using several RCD protected groups) and also identifies the isolation point from outside. It conforms with the device profile and its space requirement is module. CCC4505F000 Busbar cover ZLS00 If component modules or spare modules are not requiered, the busbar cover ensures electrically protected covering of the main and auxiliary busbars. The cover (4 modules) can be divided anywhere. The openings allow voltage measurements on the busbars without removing the cover. CCC453F000 Extension adapter ZLS0 The extension adapter, single or several side by side, can be plugged into the busbar cover via the built-in holding device. This enables conventional DIN devices with 45 mm cap size to be snapped onto the SMISSLINE socket. By plugging in several extension adapters one on top of the other, heights can be adjusted in multiples of 7 mm ABB Technical catalogue SMISSLINE TP CCC45059C003 /9
Mounting possibilities Combi module: starting solutions in kit form Direct-On-Line Starters MS6 + BEA6-4 + AF09, AF, AF6 Mounting possibilities on the combi module: The following combinations of contactor, motor circuit breaker and connector are possible on the combi module. MS6 up to 6 A + BEA6-4 + AF6, AF30, AF38 MS6 > 6 A + BEA38-4 + AF6, AF30, AF38 MS3 + BEA6-4 + AF09, AF, AF6 + I > MS... Manual motor starter BEA... Connecting link MS3 up to 0 A + BEA6-4 + AF6, AF30, AF38 AF... Contactor MS3 > 0 A + BEA38-4 + AF6, AF30, AF38 with control voltage Reversing Starters MS6 + BEA6-4, BER6-4, VEM4 + AF09, AF, AF6 MS6 up to 6 A + BEA6-4, BER38-4, VEM4 + AF6, AF30, AF38 MS6 > 6 A + BEA38-4, BER38-4, VEM4 + AF6, AF30, AF38 + I > BEA... Connecting link MS... Manual Motor Starter Fixing clip MS3 + BEA6-4, BER6-4, VEM4 + AF09, AF, AF6 MS3 up to 0 A + BEA6-4, BER38-4, VEM4 + AF6, AF30, AF38 without control voltage AF... Contactor VM4 Mechanical interlock unit VE4 Electrical interlock block MS3 > 0 A + BEA38-4, BER38-4, VEM4 + AF6, AF30, AF38 A BER..-4 Connection set A /0 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Definitions Rated short-circuit breaking capacity Icn According to EN 60898- The maximum current which a switching device can switch off without damage at a rated operational voltage and rated operational frequency. It is specified as an effective value. Rated ultimate short-circuit breaking capacity Icu According to EN 60947- Ultimate short-circuit breaking capacity that a circuit breaker can switch off without damage at a rated operational voltage and rated operational frequency. It is specified as an effective value. Rated service short-circuit breaking capacity Ics According to EN 60947- Service short-circuit breaking capacity that a circuit breaker can switch off without damage at a rated operational voltage and rated operational frequency. It is specified as an effective value. Rated insulation voltage Ui The rated insulation voltage (Ui) is the voltage to which dielectric checks and creepage distances refer. The maximum rated operational voltage must not exceed its rated insulation voltage. Rated impulse withstand voltage Uimp Peak of a withstand voltage of a specified form and polarity with which the circuit can be loaded under specified test conditions without a breakdown and to which clearances relate. The rated impulse withstand voltage must be equal to or greater than the values of the withstand over-voltages (transient overvoltages) which occur in the system in which the device is used. Rated short-time withstand current Icw The rated short-time withstand current is the effective value of the short-circuit current, as specified by the manufacturer for this circuit, that the circuit can conduct without damage. Unless otherwise specified, a time of s shall apply. Rated conditional short-circuit current Icc The rated conditional short-circuit current is the value of the prospective short-circuit current, as specified by the manufacturer, for a switching device combination that the latter can conduct during the total break time. The information about the specified short-circuit device must be given by the manufacturer. Rated fused short-circuit current Icf The rated fused short-circuit current is the conditional rated short-circuit current if the short-circuit device is a fuse in accordance with IEC 6069 [IEV 44-7-, modified]. Rated peak withstand current Ipk The rated peak withstand current is the peak value of the withstand current of the circuit of a combination of switching devices, as specified by the manufacturer. Back-up protection Assignment of two overcurrent protective devices in series, where the protective device, generally but not necessarily on the supply side, effects the overcurrent protection with or without the assistance of the other protective device and prevents excessive stress on the latter [IEC 60947-, definition.5.4]. Total selectivity Overcurrent discrimination where, in the presence of two overcurrent protective devices in series, the protective device on the load side effects the protection without causing the other protective device to operate [IEC 60947-, definition.7.]. Partial selectivity Overcurrent discrimination where, in the presence of two overcurrent protective devices in series, the protective device on the load side effects the protection up to a given level of overcurrent, without causing the other protective device to operate [IEC 60947-, definition.7.3]. ABB Technical catalogue SMISSLINE TP CCC45059C003 /
Approvals according to IEC/EN 6439-6 Busbar system Busbar system touch proof: Use only for wall mounted application (horizontal or vertical). When installed correctly the requirements of EN/IEC 6439- are met. Number of poles: max. 6 to 0 3p+N / additional bars PE+N Rated operational voltage (Ue): 690 VAC, 000 VDC (400 VAC, 50 VDC when used for load-free snap on and off under power) Rated insulation voltage (Ui): 690 VAC, 000 VDC IP Code: IP0B Mounting position: horizontal or vertical, direct mounting or mounting on DIN rail acc. to EN 6075 35 mm Pollution degree: 3 (690 V a.c.) (000 V d.c.) Rated impulse voltage (Uimp): 8 kv (all circuits) Rated current of the assembly (InA) : Max. 00 A (side feeding), max. 5 A (max. 35 C Ambient air temperature for 5 A continuously) Max. 00 A (center feeding) Max. 50 A (max. 35 C Ambient air temperature for 50 A continuously) Auxiliary circuit: max. 40 A Rated current of a circuit (Inc) : Main circuit: Max. 00 A Rated current of Auxiliary circuit: 40 A Rated short-time withstand current (Icw): 0 ka / 300 ms Auxiliary circuit: 4 ka / 50 ms Rated peak withstand current (Ipk): Main circuit: 35 ka Auxiliary circuit: 6 ka Rated diversity factor (RDF) : Rated frequency (f): 50/60 Hz Rated conditional short-circuit current (Icc): 50 ka Ambient air temperature: max. 60 C Size of CU bars 3P+N+PE: 3 x0 mm (30 mm ) Size of CU auxiliary bars La Lb: x 5 mm (0 mm ) Rated conditional short-circuit current (Icc) Incoming current of main busbars (L, L, L3, N) Short circuit protection device (SCPD) Fuse MCCB 50 A ABB Tmax 50 A 00 A NH gg 690 V/00 A ABB Tmax 50 A 60 A NH gg 690 V/60 A ABB Tmax 50 A 50 ka 63 A NH00 gg 690 V/63 A ABB Type S803S in combination with Type S803S-SCL63-SR Incoming current of auxiliary busbars (LA LB) 40 A NH00 gg 690 V/40 A ABB Type S803S in combination with Type S803S-SCL40-SR / CCC45059C003 ABB Technical catalogue SMISSLINE TP
Bus bar system Technical data and UL data s Maximum rated voltage Maximum rated current Cross-section of conductors 6 mm 50 mm, x 5 mm 3LN, Incoming terminal block ZLS4/5/8/9 690 VAC 000 VDC 60 A 3LN, 40 A LA, LB 0 mm LA, LB Incoming terminal block ZLS50 53 690 VAC 000 VDC 00 A 35 mm 95 mm max. wire, 0 5 mm or wires Incoming terminal block ZLS60 6 690 VAC 000 VDC 63 A 3LN, 6 A LA, LB mm 5 mm 3LN, LA, LB max. wire Busbar ZLS00 690 VAC 000 VDC 00 A Busbar ZLS0 690 VAC 600 VDC 40 A Universal adapters 3 A 690 VAC 600 VDC 3 A Line or neutral Universal adapters 63 A 690 VAC 600 VDC 63 A Line or neutral Combi module 690 VAC 600 VDC 3 A Line or neutral 6A LA, LB The SMISSLINE system and components are tested for vibration according to IEC 60068--6 ( 3. Hz/ mm displacement, 3. 00 Hz/0.7 g) and for Miniature circuit breakers (5 g, 0 frequency cycles 5 50 5 Hz at 0.8 rated current) Governing standard: IEC 60068--6 Environmental testing Part 6: Test Fc. Vibration (sinusoidal) Technical data according crus Busbar Incoming Incoming Universal Universal Combi module terminal block terminal component adapter adapter ZLS4, 4R, 5, 5R ZLS50, 5, 5, 53 30 A 60 A Maximum rated voltage: 600 VAC 600 VAC 600 VAC 600 VAC Maximum rated current: 00 A 50 A 00 A 30 A 60 A 30 A Rated current for supply, left or right: 00 A 00 A 00 A Rated current for supply, center: 00 A 50 A 00 A Resistance to Short circuits: 50 ka with 00 A back-up fuse Supply cable size: 4 to 0, /0 AWG 8 to 3/0 AWG ABB Technical catalogue SMISSLINE TP CCC45059C003 /3
Miniature circuit breaker Properties CCC4008Z000 N 3 N CCC4530F000 CCC4530F000 CCC45304F000 General Information The SMISSLINE miniature circuit-breaker is an energy-restricting circuit-breaker that has high performance values and that is equally suitable for the industrial sector, for commercial use and for installation at home. If a short-circuit occurs, it guarantees excellent selectivity conditions to upstream overcurrent circuit breakers while the load on equipment that is connected downstream is limited to a minimum amount. The most important features High rated breaking capacity of 0 ka or 6 ka Optimum ease of installation and connection The pole conductors are protected against accidental contact Tripping characteristic on B, C, D, K, UCZ/UCC Miniature circuit-breaker in accordance with standard EN 60898- This standard is for electrical installation material for household installations and for similar purposes. It regulates the use of miniature circuit-breakers by the layman up to a maximum of 5 A, a voltage of 440 VAC and up to a maximum of 5 ka. Miniature circuit-breaker in accordance with standard EN60947- This standard is for low-voltage material used for industrial purposes. It regulates the use of circuit-breakers (and not miniature circuit-breakers) by qualified personnel up to a maximum voltage of 000 VAC or 500 VDC. This standard does not recognise any maximum values when it comes to current and breaking capacity. In practice, the standard is also applied to miniature circuit-breakers. 3 4 CCC40403Z000 CCC45303F000 Brief description of tripping The SMISSLINE miniature circuit breakers have a current-limiting operation. They have two different releases acting on the mechanism.. Thermal release, operating with a time delay, for overload protection. Electro-magnetic release plunger operated for short-circuit protection. Oscillogram of a short-circuit current interruption 3 5 4 6 CCC40404Z000 CCC45305F0009 They offer: high short-circuit breaking capacity high selectivity to the backup fuse In the event of short-circuits, low electrodynamic and heating effects on the cable and the point of fault location due to the drastically limited let through energy ei dt. IK = peak value of prospective short-circuit current id = Max. peak let through current of circuit breaker S 400 Un = Supply voltage UB = Arc voltage of circuit breaker tk = Total interruption time ZCCC450000 3 4 5 7/N 6 8/N CCC40405Z000 /4 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Miniature circuit breaker Technical data S400E, S400M When installed correctly the requirements of EN/IEC 6439- are met. S400E, S400M General data Tripping characteristics B,C,D,K Standards IEC/EN 60898- IEC/EN 60947- Poles P, P+NP, P, 3P, 3P+NP Rated current In 0.5 A 63 A Rated frequency f 50/60 Hz Rated insulation voltage Ui acc. to DIN EN 60664-440 VAC Rated impulse withstand voltage Uimp. (./50 µs) 4 kv Overvoltage category III Pollution degree Data acc. to IEC/EN 60898- Rated operational voltage Ue P: 30/400 V AC; P+N: 30 V AC; 4P: 400 V AC; 3P+N: 400 V AC Min. operating voltage V AC V DC Rated short-circuit capacity Icn 6 ka S400E 0 ka S400M Energy limiting class 3 Reference Ambient Air Temperature for Overload Tripping B, C, D: 30 C K: 40 C Electrical and Mechanical Endurance In < 3 A: 0 000 ops (AC) In 3 A: 0 000 ops. (AC) Data acc. to IEC/EN 60947- Rated operational voltage Ue P: 40 V AC; P+N: 40 V AC; 4P: 45 V AC; 3P+N: 45 V AC; 54/440 V Min. operating voltage V AC V DC Rated ultimate short-circuit capacity Icu 5 ka (0,5 up to 6 A, 40/45 V); 0,5 to A 50 ka on request 5 ka (0 up to 63 A, 40/45 V) 5 ka (0,5 up to 6 A, 54/440 V) 6 ka (0 up to 63 A, 54/440 V) Rated service short-circuit capacity Ics 5 ka (0,5 up to 6 A, 40/45 V) 7,5 ka (0 up to 63 A, 40/45 V) 6 ka (0,5 up to 6 A, 54/440 V) 3 ka (0 up to 63 A, 54/440 V Reference Ambient Air Temperature for Overload Tripping B, C, D: 30 C K: 40 C Electrical and Mechanical Endurance In < 3 A: 0 000 operating cycles In 3 A: 0 000 operating cycles Mechanical Data Housing RAL 7035 Toggle black Classification acc. To NF F 6-0, NF F 6-0 acc. to I/F3 Protection degree acc. to EN 6059 IP0, IP40 in enclosure with cover Mechanical endurance 0 000 ops. Shock resistance acc. to IEC/EN 6373 5 g 30 ms, 3 shocks Vibration resistance acc. to IEC/EN 60068--6.3 Hz mm displacement, 3.00 Hz 0.7 g Environmental conditions (damp heat) acc. to IEC/EN 60068--30 cycles with 55 C/90 96 % and 5 C/95 00 % Ambient temperature 5 +55 C Storage temperature 40 +70 C Installation Standed Cross-section of conductors (top/bottom) upper terminal section: 0,75 5 mm lower terminal section: 0,75 0 mm Tightening torque.8 Nm Screwdriver No. Pozidrive Mounting plug in on bus bar system SMISSLINE Mounting position any Supply any Dimensions and weight Pole dimensions (H x D x W) 9 x 8 x 8 Pole weight 0 g ABB Technical catalogue SMISSLINE TP CCC45059C003 /5
Technical data Miniature circuit breaker S400UC S400UC General data Tripping characteristics UCC, UCZ Standards IEC/EN 60947- Poles P, P Rated current In 0.5 A 63 A Rated frequency f 50/60 Hz Rated insulation voltage Ui acc. to DIN EN 60664-440 V AC Rated impulse withstand voltage Uimp. (./50 µs) 4 kv Overvoltage category III Pollution degree Data acc. to IEC/EN 60947- Rated operational voltage Ue 0 V d.c. (pole) 0 V d.c. (poles ; ) 440 V d.c. (pole) 30/400 V a.c. (poles ; ) Min. operating voltage V AC V DC Rated ultimate short-circuit capacity Icu 0 ka (0,5 up to 63 A, 0 V d.c. pole) 0 ka (0,5 up to 63 A, 0 V d.c. pole) 5 ka (0,5 up to 63 A, 0 V d.c. pole) 0 ka (0,5 up to 63 A, 440 V d.c. pole) 0 ka (0,5 up to 63 A, 30/400 V) a.c. Rated service short-circuit capacity Ics 0 ka (0,5 up to 63 A, 0 V d.c. pole) 0 ka (0,5 up to 63 A, 0 V d.c. pole) 0 ka (0,5 up to 63 A, 0 V d.c. pole) 0 ka (0,5 up to 63 A, 440 V d.c. pole) 6 ka (0,5 up to 63 A, 30/400 V a.c. Reference Ambient Air Temperature for Overload Tripping 30 C Electrical and Mechanical Endurance In < 3 A: 0 000 operating cycles In 3 A: 0 000 operating cycles Mechanical Data Housing RAL 7035 Toggle black Protection degree acc. to EN 6059 IP0*, IP40 in enclosure with cover Mechanical endurance 0 000 ops. Shock resistance acc. to IEC/EN 6373 5 g 30 ms, 3 shocks Vibration resistance acc. to IEC/EN 60068--6.3 Hz mm displacement, 3.00 Hz 0.7 g Environmental conditions (damp heat) acc. to IEC/EN 60068--30 cycles with 55 C/90 96 % and 5 C/95 00 % Ambient temperature 5 +55 C Storage temperature 40 +70 C Installation Standed Cross-section of conductors (top/bottom) upper terminal section: 0,75 5 mm lower terminal section: 0,75 0 mm Tightening torque.8 Nm Screwdriver No. Pozidrive Mounting plug in on bus bar system SMISSLINE Mounting position any Supply any Dimensions and weight Pole dimensions (H x D x W) 9 x 8 x 8 Pole weight 0 g /6 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Miniature circuit breaker Trip characteristics EN60898- EN60898- EN60898- Tripping curve from cold state Tripping curve from cold state Tripping curve from cold state Tripping curve Tripping curve from cold state from cold state Seconds Minutes Seconds Minutes Seconds Minutes Seconds Minutes Seconds Minutes Seconds Minutes Multiples of rated current Multiples of rated current Trip characteristics: B Thermal trip.3...45 x In Electromagnetic trip 3...5 x In AC 4...7 x In DC Calibration temperature 30 C Multiples of rated current Multiples of rated Multiples current of rated current Multiples o Trip characteristics: C Thermal trip.3...45 x In acc. to EN60898- Thermal trip.05...3 x In acc. to EN60947- Electromagnetic trip 5...0 x In AC 7...4 x In DC Calibration temperature 30 C Trip characteristics: D Thermal trip.3...45 x In Electromagnetic trip 0...0 x In AC 5...30 x In DC Calibration temperature 30 C EN60947- EN60947- ing curve cold state Tripping Tripping curve curve from cold from state cold state Tripping curve from cold state Tripping curve from cold state Tripping curve from cold state Tripping curve from cold state Tripping curve from cold state Seconds Minutes Seconds Minutes Seconds Minutes Seconds Minutes Seconds Minutes Seconds Minutes Seconds Minutes d current Multiples Multiples of rated of rated current current Multiples of rated current Multiples of rated current Multiples of rated current Multiples of rated current Multiples of rated current Trip characteristics: K Thermal trip.05... x In Electromagnetic trip 0...0 x In AC 5...0 x In DC Calibration temperature 40 C Trip characteristics: UC Z C.05...35 x In.3...45 x In 3...5 x In DC 7...4 x In DC...3 x In AC 5...0 x In AC Calibration temperature 30 C ABB Technical catalogue SMISSLINE TP CCC45059C003 /7
Miniature circuit breaker Trip characteristics Trip characteristics example of trip curve interpretation of B-characteristics a Thermal trip characteristics: Lower test current I = defined as non-tripping current. The circuit breaker withstands.3 times the rated current for at least 60 minutes. Upper test current I = defined as trip current. The circuit breaker trips at.45 times the rated current within 60 minutes. Tripping time in s I =,3 x In 3600 000 00 0 5 a AC I =,45 x In Limiting characteristics from cold status b Electro-magnetic trip characteristics AC: The circuit breaker withstands 3 times the rated current for more than 0. sec. (in this example, up to around sec.). The circuit breaker trips in less than 0. sec. at 5 times the rated current. 0, 0,0 b DC 3 5 0 0 30 Multiple of rated current CCC4503Z000 Trip behaviour of different trip characteristics Thermal release Electromagnetic release Trip characteristics Test currents: Trip time Test currents: Trip time and current ratings lower upper lower upper test current test current test current test current I I B 4 to 63 A.3 x In > h 3 x In > 0. s.45 x In < h 5 x In < 0. s C 0.5 to 63 A.3 x In > h 5 x In > 0. s.45 x In < h 0 x In < 0. s D 6 to 63 A.3 x In > h 0 x In > 0. s.4 x In < h 0 x In < 0. s K 0.5 to 63 A.05 x In > h 8 x In > 0. s. x In < h x In < 0. s.5 x In < min 6.0 x In > s Application characteristics: B Miniature circuit breaker for circuits supplying loads generating no or only minor inrush currents (boilers, electric heaters, cookers). Application characteristics: C The standard miniature circuit breaker for circuits supplying loads producing inrush currents particular to inductive loads (TV sets, fluorescent and discharge lamps) and for socket outlets. Application characteristics: D Miniature circuit breaker for circuits supplying loads producing very high inrush currents (transformers, capacitor banks). Main circuit breaker for the back-up protection of downstream connected circuit breakers. Application characteristics: K Circuit breaker for equipment: The characteristics of these types enable the close protection requirements for equipment to be met. Application characteristics: UC Device protection in DC systems of up to 50 V = with a time constant of <5 ms (emergency networks, electroplating, etc.). /8 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Miniature circuit breaker Internal resistances at rated voltage and power losses Internal resistances and power loss per pole (cold resistance at room temperature) S400 M S400 M-UCC S400 M-UCZ Rated B, C, D K current Ri Pv Ri Pv Ri Pv Ri Pv In A Ω W Ω W Ω W Ω W 0.5 5.5.4 4.906. 6.34.6 6.34.6.44.5.505.5.55.6.55 3.5.6 0.63.6 0.594.5 0.695.8 0.695.9 0.460.8 0.45.7 0.46.9 0.46 3.9 3 0.50.4 0.8.6 0.65.5 0.65 4.5 4 0.3.9 0.50.4 0..9 0..4 6 0.05.8 0.080.9 0.05.9 0.05 3.5 8 0.09.9 0.043.7 0.038.4 0.038 3.5 0 0.0. 0.065.7 0.06.3 0.03.3 3 0.0.9 0.053.6 0.00.7 0.00. 6 0.0074.9 0.0095.4 0.0077.8 0.007.8 0 0.004.6 0.0073.9 0.0067.7 0.0067.5 5 0.003 0.0053 3.3 0.0046.9 0.005 3. 3 0.006.7 0.0034 3.4 0.005 3.6 0.005 3.7 40 0.006 4. 0.008 4.5 0.008 4.5 0.003 4.8 50 0.007 4.3 0.00 5.3 0.00 3.0 0.00 3.0 63 0.004 5.6 0.005 5.9 0.0007.8 0.0007 3.6 Currents 0.5 4 A only apply to C and K characteristics. ABB Technical catalogue SMISSLINE TP CCC45059C003 /9
Miniature circuit breaker Limitation of specific let-through energy I t l t diagrams - Specific let-through energy value l t The I t curves give the values of the specific let-through energy expressed in A s (A=amps; s=seconds) in relation to the perspective short-circuit current (Irms) in ka. S400 characteristics B C let-through energy I t [A s] let-through energy energy I t [A I t s] [A s] Prospective short-circuit current I k [ka] Prospective short-circuit current I k [ka] Prospective short-circuit current I k [ka] S400 characteristics D K let-through energy I t [A s] let-through energy I t [A s] Prospective short-circuit current I k [ka] Prospective short-circuit current I k [ka] /0 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Miniature circuit breaker Peak current Ip Limitation curves Peak current values The Ip curves give the values of the peak current, expressed in ka, in relation to the perspective symmetrical short-circuit current (ka). Characteristics B C 00 50 0 0 5 50 63 A 3 40 A 0 5 A 3 6 A 8 0 A Ip [ka] 6 A 4 A 0.5 3 A A,6 A 0,5 A Characteristics K D Ip [ka] 0. 0 0 00 50 0 0 5 0.5 0. 0 0 0. 0.5 5 0 0 50 00 Irms [ka] S400 E S400M 50 63 A 3 40 A 0 5 A 3 6 A 8 0 A 6 A 4 A 3 A A,6 A 0,5 A 0. 0.5 5 0 0 50 00 Irms [ka] S400 E S400 M CSC40044F00 CSC40043F00 ABB Technical catalogue SMISSLINE TP CCC45059C003 /
Power supply: overload and short-circuit protection Overload and short-circuit protection of the plug-in socket system Protection of the busbar system without upstream overcurrent protection An important factor for the protection of the busbar system (sockets, incoming terminal block, incoming terminal component, adapter, combi module or terminals) is the characteristic of the rated peak withstand current Ipk. The rated peak withstand current Ipk of the SMISSLINE busbar system is 35 ka. Protection of the busbar system with upstream overcurrent protection The rated short-circuit current Icf of the SMISSLINE busbar system is 50 ka. If, on the power supply side, a circuit breaker of the type Sace Tmax 00 A, a high performance circuit breaker S800 or a NH fuse is positioned upstream of the busbar system, then due to the short-circuit current limiting effect of this protection device, a larger prospective short-circuit current of up to 50 ka for the plug-in socket system is permissible. Overload and short-circuit protection of devices on the busbar system The rated short-circuit breaking capacity (or rated breaking capacity) of the protective devices, together with the maximum short-circuit current at the installation location of the devices on the busbar system, must be taken into consideration. This is not only relevant for the SMISSLINE busbar system, but is also applicable to the distribution construction. Miniature circuit breaker If the prospective short-circuit current at the installation location of a miniature circuit breaker is not greater than its rated breaking capacity, no back-up protection via an upstream overcurrent protection device is necessary. If the prospective short-circuit current at the installation location of a miniature circuit breaker is greater than its rated short-circuit breaking capacity, the current ratings of the upstream overcurrent protection device must not exceed the table values in the back-up tables (catalogue, page /0 onwards). Residual-current circuit breaker A back-up fuse with max. 00 A gl/gg or a high performance circuit breaker S800 00 A is required for short-circuit protection upstream or downstream (see Coordination table, page /4). A back-up fuse is not required up to the level of the internal short-circuit withstand rating. Thermal protection can be ensured by means of downstream miniature circuit breakers, but only if the rated currents do not exceed the value of the current rating of the residualcurrent circuit breaker in consideration of a utilisation factor. Surge arrester OVR An upstream overcurrent protection device with max. 60 A gl/gg is necessary for shortcircuit protection (in the case of non-independent interruptions of the secondary current). Back-up fuses for devices with a universal adapter In principle, the same requirements apply as for directly plugged-in devices. / CCC45059C003 ABB Technical catalogue SMISSLINE TP
Technical Catalogue, Version 03 Back-up and selectivity dates: see catalogue on ABB homepage Back-up and selectivity dates Back-up and Selectivity tables S800, SMISSLINE with ABB Products More Back-up and Selectivity tables: see www.abb.ch Catalogue CCC45039L009 SOC - Selected Optimized Coordination See as well ABB on http://applications.it.abb.com/soc_snb ABB Technical catalogue SMISSLINE TP CCC45059C003 /3
Miniature circuit breaker Back-up protection with fuses, S800 a) If the short-circuit current at the point of installation of the circuit breaker is not greater than the nominal breaking capacity of the MCB, an upstream fuse is not needed. If a fuse is fitted upstream for installation reasons, any nominal current may be selected for the fuse. b) If the short-circuit current at the point of installation of the circuit breaker is greater than its nominal breaking capacity, the nominal currents of the upstream fuses must not exceed the values specified in the table (back-up protection of the circuit breaker). Upstream: Fuse NH..gL/gG L. Icu [ka] S400M/S450M FS40M/FS45M FS403M/FS453M S400E/S450E FS40E/FS45E FS403E/FS453E Icn [ka] 0 Icn [ka] 6 E. = Upstream L. = Downstream Selectivity limits are specified in ka S. NH gl/gg In [A] 5 40 63 80 00 5 60 00 all types all types 00 00 00 00 80 50 30 0 00 00 70 40 5 5 0 S800S S400M (SMISSLINE) @ 30/400 V S. S800S Char. B, C, D, K L. Icu [ka] 50 In [A] 5 3 40 50 63 80 00 5 Icn [ka] 4* 6 50 50 50 50 50 50 50 50 0 50 50 50 50 50 50 50 5 50 50 50 50 50 50 S400M FS40M FS403M B, D 0 3 50 50 50 50 50 40 50 50 50 50 50 50 50 50 63 50 50 S. S800S Char. B, C, D, K L. Icu [ka] 50 In [A] 5 3 40 50 63 80 00 5 50 0.5 50 50 50 50 50 50 50 50 5 3...0 50 50 50 50 50 50 50 50 5 50 50 50 50 50 50 S400M C, K 3 50 50 50 50 50 5 40 50 50 50 50 50 50 50 50 63 50 50 S800N S400M (SMISSLINE) @ 30/400 V S. S800N Char. B, C, D L. Icu [ka] 36 In [A] 5 3 40 50 63 80 00 5 Icn [ka] 4* 6 36 36 36 36 36 36 36 36 0 36 36 36 36 36 36 36 5 36 36 36 36 36 36 S400M FS40M FS403M B, D 0 3 36 36 36 36 36 40 36 36 36 36 50 36 36 36 63 36 36 E. = Upstream L. = Downstream Selectivity limits are specified in ka S. S800 N Char. B, C, D L. Icn [ka] 36 S400M C, K In [A] 5 3 40 50 63 80 00 5 50 0.5... 36 36 36 36 36 36 36 36 5 3...0 36 36 36 36 36 36 36 36 5 36 36 36 36 36 36 5 3 36 36 36 36 36 40 36 36 36 36 50 36 36 36 63 36 36 Consulting the back-up table This table provides the value (in ka) for which the back-up protection is ensured between a given combination of circuit breakers. The table covers possible combinations between the S800 or SACE series Tmax and between SMISSLINE miniature circuit breakers 400 M. /4 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Miniature circuit breaker Back-up protection with Tmax and XT Sace Tmax S400 @ 30/400 V Up- T T T T T3 T4 T T3 T4 T T4 T T4 T4 Stream Version Version B C N N N N S S S H H L V Downstream ln [A] lcu [ka] 6 5 36 36 36 36 50 50 50 70 70 85 0 00 S400E FS40E/403E S400M FS40M/403M S400M FS40M/403M B, C C, K B, D 6 0 36 36 40 40 40 30 40 40 40 3 63 6 6 5 30 36 6 6 36 6 6 6 6 6 6 6 0.5 0 36 36 40 40 50 40 50 40 40 3 63 0 6 5 30 36 5 36 40 5 40 50 40 50 40 40 6 0 36 36 40 40 50 40 50 40 40 3 63 0 6 5 30 36 5 36 40 5 40 50 40 50 40 40 Sace XT S400 @ 30/400 V Up- Stream XT XT XT3 XT4 XT XT XT3 XT4 XT XT XT4 XT XT4 XT XT4 Version Version B C N S H L V Downstream ln [A] lcu [ka] 8 5 36 50 70 0 50 FS400E 6 0 36 40 S400E B, C S450E 3 63 6 8 5 30 36 6 36 30 36 6 40 30 40 40 40 40 40 40 FS400M 0.5 0 36 40 70 85 85 S400M C, K S450M 3 63 0 8 5 30 36 5 36 30 50 5 40 30 60 40 60 40 60 40 FS400M 6 0 36 40 70 85 85 S400M B, D S450M 3 63 0 8 5 30 36 5 36 30 50 5 40 30 60 40 60 40 60 40 Supply side Load side S800N - S400E @ 30/400 V E. S800N Char. B, C, D L. Icu [ka] 36 S400E B 6 In [A] 5 3 40 50 63 80 00 5 6 36 36 36 36 36 36 36 36 0 36 36 36 36 36 36 36 36 3 36 36 36 36 36 36 36 36 6 36 36 36 36 36 36 36 36 0 36 36 36 36 36 36 36 5 36 36 36 36 36 36 3 36 36 36 36 36 40 36 36 36 36 36 36 36 36 63 36 36 Example : With a S800 nominal current 50 A is a Back-up protection till a nominal current of 5 A to a S400 given. The Back-up protection ist till 36 ka. Example : There is no Back-up protection between supply side and the load side given. Back-up protection The tables given provide the value (in ka, referring to the breaking capacity) for which the back-up protection among the combination of selected circuit breakers is verified. The tables cover the possible combinations between S800 and those between the above mentioned circuit breakers and the ABB series of modular circuit breakers S400. The values indicated in the tables refer to the voltage: Vn of 30/400VAC ABB Technical catalogue SMISSLINE TP CCC45059C003 /5
Miniature circuit breaker Influence of ambient temperature Allowable current of miniature circuit breakers depending on ambient temperature and max. load current for row mounted miniature circuit breakers. Practical procedure Conditions often arise which allow for simple consideration of the ambient temperature and thermal influences of row mounted circuit breakers according to EN 60898 and EN 60947-. The following procedure has proven to be effective:. Selection of circuit breaker according to the rated current of the equipment or the current carrying capacity of the cable depending on whitch of these is the lower value.. Consideration of thermal factors for an ambient temperature of 40 C: IB 0,9 x In for thermal influence of row mounted circuit breakers subject to the same loads: IB 0,75 x In 3. This results in the rated current of the circuit breaker to be selected for In,5 times the relevant current according to point. This procedure considers all thermal influence factors and results in an optimum choice of the rated current for the circuit breaker. Example: Current carrying capacity required of the cable: 4 A. Selected rated current of circuit breaker taking thermal influence into consideration: In O,5 x 4 A 6 A. Basis for the simplified procedure. Different ambient temperature The thermal releases are set to a reference ambient temperature. For trip characteristic K, this is 40 C, for trip characteristics B, C and D, this is 30 C. At different ambient temperatures, the specified current values change by around 6 % per 0 C difference in temperature. For more accurate calculations and very high or very low ambient temperatures, the following tables apply:. Influence of row mounted devices at continuous load If the circuit breakers are lined up close to one another and have equally high load levels, a correction factor must be taken. This influence can be reduced if fillers and/or spacers (9 mm wide) are used. Influence of adjacent devices S400 Fm Factor.0 0.9 0.8 0.7 0.6 3 4 5 6 7 8 9 Number of devices OEPM008 Influence of adjacent devices Correction factor Fm No. of correction adjacent devices factor 0.95 3 0.9 4 0.86 5 0.8 6 0.8 7 0.78 8 0.77 9 0.76 >9 0.76 /6 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Miniature circuit breaker Influence of ambient temperature Max. operating currents depending on ambient temperature for S400 miniature circuit breakers of tip characteristics B, C, D, UC-C and UC-Z In(A) Ambient temperature T ( C) 0 0 5 0 5 30 35 40 45 50 55 0.5* 0.58 0.55 0.53 0.5 0.5 0.50 0.48 0.47 0.46 0.44 0.43.0*.5.09.07.04.0.0 0.97 0.94 0.9 0.89 0.86.6*.85.75.7.67.63.6.55.50.46.4.38.0*.3.9.3.08.03.0.93.88.83.77.7 3.0* 3.5 3.3 3.4 3.6 3.09 3.0.93.85.77.69.6 4.0* 4.6 4.37 4.7 4.7 4.07 4.0 3.86 3.76 3.66 3.56 3.45 6.0 6.9 6.59 6.44 6.9 6.4 6.0 5.83 5.68 5.53 5.37 5. 8.0 9. 8.84 8.63 8.4 8. 8.0 7.8 7.6 7.39 7.9 6.98 0.0.5 0.9 0.7 0.4 0. 0.0 9.65 9.39 9.4 8.88 8.63 3.0 5.0 4.4 4.0 3.7 3.3 3.0.7.3.0.6.3 6.0 8.5 7.6 7. 6.8 6.4 6.0 5.6 5. 4.7 4.3 3.9 0.0 3...6.0 0.5 0.0 9.5 9.0 8.5 8.0 7.5 5.0 8.9 7.5 6.9 6.3 5.6 5.0 4.3 3.7 3.0.4.8 3.0 37.0 35.3 34.5 33.7 3.8 3.0 3. 30.4 9.5 8.7 7.9 40.0 46. 44. 43.0 4.0 4.0 40.0 39.0 37.9 36.9 35.9 34.9 50.0 57.7 55 53.7 5.4 5. 50.0 48.6 47.3 46.0 44.7 43.4 63.0 7.7 69.3 67.7 66. 64.5 63.0 6.3 59.7 58. 56.4 54.8 * only applies to C Max. operating currents depending on ambient temperature for S400 miniature circuit breakers of trip characteristic K In(A) Ambient temperature T ( C) 0 5 0 5 30 35 40 45 50 55 0.5 0.54 0.5 0.5 0.50 0.49 0.47 0.5 0.45 0.43 0.4.0.4..09.07.0.0.0 0.96 0.94 0.9.6.85.8.77.73.7.65.6.56.5.48.0.9.3.8.3..03.0.93.87.8 3.0 3.48 3.40 3.3 3.5 3. 3.09 3.0.93.85.77 4.0 4.58 4.48 4.38 4.8 4. 4.07 4.0 3.87 3.77 3.66 6.0 6.9 6.76 6.6 6.46 6.3 6.5 6.0 5.85 5.69 5.54 8.0 9.4 9.03 8.8 8.6 8.4 8. 8.0 7.79 7.59 7.38 0.0.5..0 0.7 0.5 0. 0.0 9.69 9.43 9.8 3.0 5. 4.7 4.4 4.0 3.7 3.4 3.0.7.3.0 6.0 8.4 8.0 7.6 7. 6.8 6.4 6.0 5.6 5. 4.8 0.0 3.0.5.0.5 0.9 0.4 0.0 9.4 8.9 8.4 5.0 8.9 8.3 7.6 7.0 6.3 5.7 5.0 4.4 3.8 3. 3.0 36.9 36. 35.3 34.4 33.6 3.8 3.0 3. 30.3 9.5 40.0 46. 45. 44. 43. 4. 4. 40.0 39.0 38.0 37.0 50.0 57.7 56.4 55. 53.8 5.5 5.3 50.0 48.7 47.4 46. 63.0 7.5 70.9 69.3 67.7 66. 64.5 63.0 6.3 59.6 58.0 ABB Technical catalogue SMISSLINE TP CCC45059C003 /7
Miniature circuit breaker Protection of circuits with fluorescent lamps Protection of circuits with fluorescent lamps The following table gives the maximum permissible number of fluorescent lamps which can be protected by a single-pole circuit breaker of characteristic. The figure for multi-pole circuit breakers is reduced by 0%. Rated current FL not compensated FL compensated in parallel FL with electronic ballast KVG KVG EVG ) 8/0 W 36/40 W 58/65 W 8/0 W 36/40 W 58/65 W 8/0 W 36/40 W 58/65 W 3 35 30 9 4 4 7 0 6 43 37 4 5 5 33 6 6 0 53 46 30 64 64 4 33 33 5 5 66 58 37 8 8 53 4 4 9 ) EVG: Two-lamp version, lamps switched together, electronic ballast KVG: Conventional ballast Use of miniature circuit breakers S400 M for DC systems A standard miniature circuit breaker type S400 M and S400 E can be used in a DC system by observing the following conditions: Single pole miniature circuit breaker max. 60 V DC. -pole miniature circuit breaker with -poles in series max. 5 V DC. The polarity needs not to be taken into account. Load connection can either be at the top or at the bottom of the MCB. Example of permissible DC voltages depending on the number of poles and the circuit configeration in earthed DC systems: x x x 3 x x 3 x x 3 4 4 4 60 V 0 V ( ) 5 V 0 V ( ) 5 V 0 V ( ) 60 V 60 V 0 V ( ) CCC4509Z000 Examples for different voltages between a conductor and earth where voltages between conductors are identical: x x 3 x x x 3 5 x 7 4 4 6 8 + 60 V + 5 V CCC4500Z000 /8 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Miniature circuit breaker S400UC UC = Universal Current = AC/DC S400UC MCBs can be used in the one-pole version as 50 V d.c., and in the -pole version with series connection of two poles up to 440 V d.c.. For DC incoming supply from above S400 UC-... MCBs have, in the area of arc chutes, permanent magnets, it is therefore necessary to take into account the polarity during the installation process. Doing so ensures that in the case of a short circuit the magnetic field of the permanent magnets corresponds with the electromagnetic field of the short-circuit current, therefore safely leading the short circuit into the arc chute. Incorrect polarities may cause damage to the MCB. This is why in the case of top-fed devices terminal must be connected to ( ) and terminal 3 (+). Example for permissible voltages between the conductors depending on the number of poles and circuit layout: voltage UN between 50 V d.c. 440 V d.c. 440 V d.c. 440 V d.c. conductors voltage UN between 50 V d.c. 50 V d.c. 440 V d.c. 50 V d.c. conductor and earth supply 3 4 3 4 3 4 L + L L + L L + L L + L M ABB Technical catalogue SMISSLINE TP CCC45059C003 /9
Residual current operated circuit breaker F40, F404 Properties / 3/4 5/6 7/8/N / 4/3 6/5 8/7/N CCC40408Z000 CCC45365F000 General information about residual current operated circuit breakers The residual current operated circuit breaker prevents personal injury and damage to property caused by electric current. Use of this circuit breaker is required in various national and international standards for electrical installations. Modern residual current operated circuit breakers respond to small residual currents. Interruption occurs in a fraction of a second even before a hazardous situation for people, animals and property can arise. The principle of magnetic tripping independable of the supply voltage ensures perfect and safe operation even in the event of undervoltage and neutral interruptions. The key features High short-circuit resistance 0 ka Sensitive for alternating and pulsating DC residual currents - and 4-pole types Nominal residual trip currents 0, 30, 00, 300 and 500 ma Snap-on auxiliary switches and signal contacts Nominal currents 5, 40, 63 A Double terminals According to the wave form of the earth leakage currents they are sensitive to, the RCDs may be classed as: A type (for alternating and/or pulsating current with DC components AC type (for alternating current only) ABB SMISSLINE RCD s are all type A. Shape of the fault current Correct RDC function alternating current Type AC pulsating current sensitiv Type A sinusoidal a.c. rampant slowly rising pulsating d.c. rampant with or without overlapping DC components from 6 ma slowly rising CCC45096Z000 Selectivity RCDs raise similar issue to those surrounding the installation of MCBs, and in particular the need to reduce to a minimum the parts of the system out of order in the event of a fault. For RCBOs the problem of selectivity in the case of short-circuit currents may be handled with the same specific criteria as for MCBs. However, for correct residual current protection, the more important aspects are linked to tripping times. Protection against contact voltages is only effective if the maximum times indicated on the safety curve are not exceeded. /30 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Residual current operated circuit breaker F40, F404 Properties Partial selectivity A I 0.5 x I I B I 0.5 x I I dubious selectivity safe selectivity safe selectivity CCC45087Z000 Total selectivity 300 ma s F400 S Protection of complete installation Outgoing lines without person protection 30 ma 0 ma High sensitivity or short time delayed residual current operated circuit breaker for person protection Z030.eps Amperometric (partial) selectivity Selectivity may be created by placing low-sensitivity RCDs upstream and higher-sensitivity RCDs downstream. An essential condition which must be satisfied in order to achieve selective co-ordination is that the I value of the breaker upstream (main breaker) is more than double the IΔ value of the breaker downstream. The operative rule to obtain an amperometric (partial) selectivity is IΔn of the upstream breaker = 3 x IΔn of the downstream breaker (e. g.: F404, 300 ma upstream; F40, 00 ma downstream). In this case, selectivity is partial and only the downstream breaker trips for earth fault currents IΔ < IΔm < 0,5 x IΔ). Chronometric (total) selectivity To achieve total selectivity, delayed or selective RCDs must be installed. The tripping times of the two devices connected in series must be co-ordinated so that the total interruption time t of the downstream breaker is less than the upstream breaker s no-response limit time t, for any current value. In this way, the downstream breaker completes its opening before the upstream one. To completely guarantee total selectivity, the IΔ value of the upstream device must also be more than double that of the downstream device in accordance with IEC 64-8/563.3, comments. The operative rule to obtain an amperometric (partial) selectivity is IΔn of the upstream breaker = 3 x IΔn of the downstream breaker (e. g.: F404, S type, 300 ma upstream). For safety reasons, the delayed tripping times of the upstream breaker must always be below the safety curve. ABB Technical catalogue SMISSLINE TP CCC45059C003 /3
Residual current operated circuit breaker F40, F404 Standard, short-time delayed and selective type The use of multiple electronic reactors for the supply of fluorescent lamps instead generates permanent leakage currents and inrush currents that can provoke nuisance tripping of a standard residual current breaker. IT system loads and other electronic equipment (e.g. dimmers, computers, inverters) with capacitive input filters connected between the phases and ground can also generate permanent earth leakage currents whose sum may provoke the nuisance tripping of a standard residual current breaker. For these situations, the SHORT-TIME DELAY breakers allow a greater number of devices to be connected to the installation. Soft-starters for motors are loads which can generate high-frequency capacitive currents (provoked by the harmonics) toward ground or fed into the network. Also in this case, the use of SHORT-TIME DELAY residual breakers reduces the sensibility to nuisance tripping. Compared with standard type breakers, SHORT-TIME DELAY residual current breakers are therefore characterised, for any given sensibility, by: Higher residual trip current Tripping time delay Better resistance to overvoltages, harmonics and impulse disturbances. Regulations The tests set out in the IEC 6008 and IEC 6009 standards verify the resistance of residual current breakers to unwanted tripping provoked by operation overvoltages, using a ring wave impulse shape of 0.5 μs/00 khz. All residual current circuit-breakers are required to pass this test with a peak current value of 00 A. For what concerns atmospheric overvoltages, the IEC 6008 and 6009 standards prescribe the 8/0 μs surge test with a 3000 A peak current, but limit the requirement to residual current devices classified as selective; no test is required for other types. The ABB range of SHORT-TIME DELAY anti-nuisance tripping breakers and blocks pass the general 0.5 μs/00 khz ring wave test and also withstand the 8/0 μs impulse test with the same peak current of 3000 A prescribed for selective devices. The F40 K and F404 K should therefore be used to prevent unwanted tripping. Three different types of Residual current operated circuit breaker standard RCD 30 ma selective RCD 300 ma S short-time delay RCD 30 ma K Tripping t (s) 0.5 0.3 0. 0.5 0.3 0.0 0.06 0.05 0.04 short-time delay 30mA K selectiv 300mA S 0.0 standard 30mA 0 00 50 300 600 500 standard 30mA I n x I n 5 x I n selectiv 300mA I n I n x I n 5 x I n I n (ma) CCC45089Z000 The standard RCD 30 ma tripp after circa ma and a release time of 35 ms. The selectiv RCD 300 ma tripp after circa 00 ma and a release time of circa 80 ms. The short-time delay RCD 30 ma tripp after circa 5 ma and a release time of 00 0 ms. /3 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Residual current operated circuit breaker F40, F404 Standard, short-time delayed and selective type Unwanted tripping In the event of disturbance in the mains, the RCDs normally present in the system are tripped, breaking the circuit even in the absence of a true earth fault. Disturbances of this kind are most often caused by: operation overvoltages caused by inserting or removing loads (opening or closing protection of control devices, starting and stopping motors, switching fluorescent lighting systems on and off, etc.) overvoltages of atmospheric origin, caused by direct or indirect discharges on the electrical line. Under these circumstances, breaker tripping is unwanted, since it does not satisfy the need to avoid the risks due to direct and indirect contacts. On the contrary, the sudden and unjustified interruption of the power supply may result in very serious problems. SHORT-TIME DELAY RCDs The ABB range of SHORT-TIME DELAY anti-disturbance residual current circuitbreakers and blocks was designed to overcome the problem of unwanted tripping due to overvoltages of atmospheric or operation origin. The electronic circuit in these devices can distinguish between temporary leakage caused by disturbances on the mains and permanent leakage due to actual faults, only breaking the circuit in the latter case. SHORT-TIME DELAY residual current circuit-breakers and blocks have a slight delay into the tripping time, but this does not compromise the safety limits set by the Standards in force (release time at I n =50 ms). Guaranteeing conventional residual current protection, their installation in the electrical circuit therefore allows any unwanted tripping to be avoided in domestic and industrial systems in which service continuity is essential. This delay makes the SHORT-TIME DELAY residual current devices especially suited for installations involving motor starters/variable speed drives, fluorescent lamps or IT/electronic equipment. Table of RDC selectivity Upstream I n 0 30 00 300 300 500 500 [ma] Downstream I n inst inst inst inst S inst S [ma] 0 inst n n n n n n 30 inst n n n n n 00 inst n n n 300 inst 300 S 500 inst 500 S inst = instantaneous S = selective n = amperometric (partial) selectivity n = chronometric (total) selectivity ABB Technical catalogue SMISSLINE TP CCC45059C003 /33
Residual current operated circuit breaker F40, F404 Technical data F40 F404 Rated voltage Un: 30 V 30/400 V Number of poles: 4 Rated frequency fn: 50/60 Hz 50/60 Hz (for Type LF 6 /3 Hz) Rated breaking capacity Im: 000 A Total trip time (average value) at I n # 300 ms # 300 ms at 5 I n # 40 ms # 40 ms Delay time at 5 I n: Resistance to short circuits (ka): 0 ka 0 ka in conjunction with an upstream fuse in conjunction with an upstream fuse gl / gg 00 A or a high performance gl / gg 00 A or a high performance MCB S800, 00 A MCB S800, 00 A Connection Double lift terminal touch finger-proof, suitable for connecting load side terminal single-, multi- and fine-wire conductors of up to 5 mm Degree of protection: IP0 inside panel IP40 IP0 inside panel IP40 Endurance: > 5000 operating cycles > 5000 operating cycles Resistance to climate acc. to: EN 6008 EN 6008 Mounting position: any any Ambient temperature: 5 C +40 C 5 C +55 C acc. to EN 6009 Vibration resistance: 5 g 5 g 5 50 5 Hz 5 50 5 Hz Plastic parts: halogen-free halogen-free Contacts: cadmium-free cadmium-free F40 K F404 K F404 S Rated voltage Un: 30 V 30/400 V 30/400 V Number of poles: 4 4 Rated frequency fn: 45 60 Hz 45 60 Hz 45 60 Hz Resistance to surge current: 3 ka 3 ka 5 ka 8/0 µs 8/0 µs 8/0 µs Total trip time (average value) at I n 40 ms 0 300 ms 50 500 ms at 5 I n # 40 ms 40 50 ms Delay time at 5 I n: 0 ms 0 ms 90 ms Resistance to short circuits (ka): 0 ka 0 ka 0 ka in conjunction with an upstream fuse gl / gg 00 A or or a high performance MCB S800 00 A Connection Double lift terminal touch finger-proof, suitable for connecting load side terminal single-, multi- and fine-wire conductors of up to 5 mm Degree of protection: IP0 in panel IP40 IP0 in panel IP40 IP0 in panel IP40 Endurance: > 5000 operating cycles > 5000 operating cycles > 5000 operating cycles Resistance to climate acc. to: EN 6008 EN 6008 EN 6008 Mounting position: any any any Ambient temperature: 5 C +40 C 5 C +55 C 5 C +40 C Vibration resistance: 5g 5g 5g 5 50 5 Hz 5 50 5 Hz 5 50 5 Hz Plastic parts: halogen-free halogen-free halogen-free Contacts: cadmium-free cadmium-free cadmium-free /34 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Residual current operated circuit breaker F40, F404 Technical data Coordination tables between Short Circuit Protection Devices (SCPD) and F404 RCCBs If you are using an RCCB you must verify that the Short Circuit Protection Device (SCPD) protects it from the effects of high current that arise under short-circuit conditions. The IEC/EN 6008 provides some tests to verify the behaviour of RCCB in short-circuit conditions. The tables below provide the maximum withstanding short-circuit current expressed in eff. ka for which the RCCBs are protected thanks to the coordination with the SCPD with a rated current (thermal protection) less than or eqaul to the rated current of the associated RCCB. F404 5 A F404 40 A F404 63 A gg fuse 5 A 00 gg fuse 40 A 60 60 gg fuse 63 A 0 0 0 gg fuse 00 A 0 0 0 S403M 0 0 0 S803N 0 0 0 S803S 5 5 5 Internal resistances and power losses of RCCBs and RCBOs Internal resistances and power losses per pole (cold resistance at room temperature) 4-pole RCCB F404 -pole RCCB F40 Ri Pv Type Ri Pv in A mω W mω W 5..3 5 A/0 ma 8.8 5.5 40.0 3. 5 A/30 ma 6. 3.8 63. 4.4 40 A/30 ma 5.8 9.3 ABB Technical catalogue SMISSLINE TP CCC45059C003 /35
Residual current operated circuit breaker FS40 / 3/4/N / 4/3/N CCC45364F000 CCC40407Z000 Residual current operated circuit breakers with overcurrent protection (RCBO) The SMISSLINE residual current operated circuit breakers with overcurrent protection (RCBO) are ideal for protecting people and property in all new and existing distribution systems. The combination of standby current and cable protection in one single device greatly simplifies planning and offers cost benefits. Using a RCBO can e.g. satisfy the minimum level of protection required by regulations in an apartment or in a particular distribution system. Should a residual current arise, only the circuit directly affected is switched off while all other circuits remain in operation. The short time-delayed residual current operated circuit breaker with overcurrent protection FS40 K is a version particularly suited to unfavourable distribution and load situations. Without limiting the personal protection function in any way, the electronic short time delay prevents nuisance tripping which may arise as a result of capacitive discharge currents. FS40 FS40K Rated voltage Un: 30 V ~ 30 V ~ Upstream fuses and For backup and selectivity, the details for the miniature circuit breakers S400 E Selectivity limits: and S400 M Page /9 to /36 Number of poles: -pole (PN) -pole (PN) Rated frequency fn: 50/60 Hz 50/60 Hz Rated breaking capacity Icn: 0 ka 30 V ~ (0 6 A nominal current) 0 ka 30 V ~ (0 6 A nominal current) 6 ka 30 V ~ (0 3 A nominal current) 6 ka 30 V ~ (0 A nominal current) Current limitation class: 3 3 Total cut-off time (average value) acc. to EN 6009- EN 6009- at In 40 ms 40 ms at 5 I n 5 ms 35 ms Delay time at 5 I n: 0 ms Minimum voltage for test button 70 V 70 V Connection cross-sections Opposing action stroke clamp on cylinder, touch finger-proof. Suitable for connecting Terminal at load end single, multi- and fine-wire conductors of up to 5 mm Degree of protection: IP0 inside panel IP40 IP0 inside panel IP40 Endurance: > 5000 operating cycles > 5000 operating cycles Resistance to climate, acc. to: EN 6009 EN 6009 Mounting position: any any Ambient temperature: 5 C... +40 C 5 C... +40 C Vibration resistance: 5 g 5 g 5...50... 5 Hz 5...50... 5 Hz Plastic parts: halogen-free halogen-free Contacts: cadmium-free cadmium-free Please notice: For the influence of the ambient temperature and the thermal influences of row mounted RCBO s it is necessary to calculate with the same correction factors like with MCB s. /36 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Residual current operated circuit breaker FS40 Internal resistances and power losses, Derating Max. operating currents depending on ambient temperature for RCBO of tip characteristics B and C. Influence of adjacent devices B,C Ambient temperature T ( C) No. of adjacent devices correction factor In (A) 5 0 0 0 0 0 30 40.6.5.4.3...9 0.95 4 4.9 4.8 4.6 4.5 4.3 4. 4 3.8 3 0.9 6 7.95 7.8 7.4 7. 6.7 6.4 6 5.6 4 0.86 8 0.3 0. 9.7 9.3 8.8 8.4 8 7.6 5 0.8 0.8.6.3 0.7 0.3 0 9.7 6 0.8 3 5.65 5.4 4.9 4.4 4 3.5 3.5 7 0.78 6 8.65 8.4 7.9 7.4 7 6.5 6 5.5 8 0.77 0 3..8..7. 0.6 0 9.4 9 0.76 5 30.8 30.3 9. 8. 7. 6. 5 3.9 0 0.76 3 39.3 38.6 37.3 36 34.7 33.3 3 30.7 40 50.7 49.7 47.8 45.8 43.9 4.9 40 38. -pole RCBO FS40 Type Ri Pv mω W C0/0.03 7.0.7 C3/0.0.0 3.58 C3/0.03 5.0.55 C6/0.0 3.0 3.33 C6/0.03 0.4.67 B6/0.03 0.9.45 B3/0.03 5.0 3.33 C0/0.03 8.0 3.0 C5/0.03 7.0 4.38 C3/0.03 5.4 5.53 ABB Technical catalogue SMISSLINE TP CCC45059C003 /37
Residual current operated breaker RCBO FS403 CCC4558F000 4-pole RCBO from the ABB SMISSLINE protective devices range The combination of circuit protection and a residual current protection in one device as 4-pole RCBO simplifies both planning and installation. It enables you to provide perfect protection in one device. This protection consists of: Short circuit protection Overload protection Residual current protection Preventive fire protection High rated short-circuit breaking capacity of 0 ka, conforming to EN 6009- The Icn 0 ka short-circuit breaking capacity of the RCBO complies with standard EN 6009-. This standard specifies testing and usage of RCBO s for household and similar uses. The devices can also be used by non-professionals. Features and benefits of the new devices: Overall width of 7 mm (4 modules) Rated sensitivity 30 ma Current rating 0 A to 3 A B and C tripping characteristics Easy Drive double deck terminals on the output side for connecting two conductors in one chamber. The two chambers can accommodate conductors with different cross sections. Rated voltage Un: Number of poles: Rated frequency fn: Rated breaking capacity Icn: FS403 40/45 V 3PN 50/60 Hz 0 ka bzw. 6 ka Current limitation class: 3 Total cut-off time (avarage time) acc. to IEC/EN 6009- at IΔn at 5IΔn EN6009 40 ms 5 ms Minimum voltage for test button 70 V Standed Cross-section of conductors (top/bottom) Upper terminal part 0,75 35 mm Tightening torque: Degree of protection: Endurance: > 5000 Resistance to climate: Lower terminalpart 0,75 0 mm.8 Nm IP0 according to EN6009 Ambient temperature: 5 C +40 C Vibration resistance: EN 6009- Plastic parts: contacts: Approvals and standards: Accessory: Auxiliary- and signal contacts are to attach on to the left of the device through the customer. halogen free, according IEC 6-49-- cadminum free EN/IEC 6009-, SEV /38 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Residual current operated circuit breaker FS403 Internal resistances and power losses, Derating Internal resistances and power losses Internal resistances and power losses per pole (cold resistance at room temperature) FS403 Typ Ri Ri Pv mω für L mω für N W 6A B, C 48..9 3 0A B, C 5.5..69 3A B, C 0..8.96 6A B, C 7.9.9 3.5 0A B, C 5.6.7 3.94 5A B, C 4.8.7 5.9 3A B, C 3.6.5 6.38 Performances at different ambient temperatures Max. operating current depending on the ambient temperature of a circuit-breaker in load circuit of characteristics type B, C Influence of adjacent devices Correction factor Fm B,C Ambient temperature T ( C) No. Of adjacent devices correction factor In (A) 5 0 0 0 0 0 30 40 6 7.95 7.8 7.4 7. 6.7 6.4 6 5.6 4 0.86 0.8.6.3 0.7 0.3 0 9.7 6 0.8 3 5.65 5.4 4.9 4.4 4 3.5 3.5 7 0.78 6 8.65 8.4 7.9 7.4 7 6.5 6 5.5 8 0.77 0 3..8..7. 0.6 0 9.4 9 0.76 5 30.8 30.3 9. 8. 7. 6. 5 3.9 0 0.76 3 39.3 38.6 37.3 36 34.7 33.3 3 30.7 ABB Technical catalogue SMISSLINE TP CCC45059C003 /39
RCBO FS40, FS403 Limitation of specific let-through energy I t, peak current Ip l t diagrams - Specific let-through energy value l t The I t curves give the values of the specific let-through energy expressed in A s (A=amps; s=seconds) in relation to the perspective short-circuit current (Irms) in ka. FS400M characteristics B C let-through energy I t [A s] let-through energy I t [A s] Prospective short-circuit current I k [ka] Prospective short-circuit current I k [ka] Limitation curves Peak current values The Ip curves give the values of the peak current, expressed in ka, in relation to the perspective symmetrical short-circuit current (ka). FS400M Characteristics B C 00 50 0 0 5 50 63 A 3 40 A 0 5 A 3 6 A 8 0 A Ip [ka] 6 A 4 A 0.5 3 A A,6 A 0,5 A 0. 0 0 0. 0.5 5 0 0 50 00 Irms [ka] S400 E S400M CSC40043F00 /40 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Switch disconnector Technical data / 3/4 5/6 7/8/N / 4/3 6/5 8/7/N CCC404030Z000 CCC45366F000 General switch disconnector When used in a smissline socket system, the switch disconnector can be used instead of the incoming terminal block for up to 63 A. With the smissline IS404 switch disconnector, individual loads, groups of loads or entire system parts can be separated or connected to the input supply. The key features of the switch disconnector Input supply switch On-Off function Clear indication of switching position Snap-on auxiliary switch available Uniform smissline design Technical data for switch disconnector IS404 Rated voltage Un: 30/400 V ~ Rated current In: 63 A Rated frequency fn: 50 Hz Number of poles: 4 Rated impulse withstand voltage: 6 kv Connection cross-sections Cu: At top, touch finger-proof. Suitable for connecting up single-, multi- and fine-wire conductors of up to 5 mm Degree of protection: IP40 Endurance, mechanical/electrical: 5000 operating cycles Mounting position: any Ambient temperature: 5 C... +40 C Specifications: EN/IEC 60947-3 Approvals: SEV Weight (approx.): 50 g Switching duty: AC-A Plastic parts: halogen-free Contacts: cadmium-free ABB Technical catalogue SMISSLINE TP CCC45059C003 /4
Surge arrester OVR Properties CCC4545F000 The type surge arresters in the QuickSafe product range are suitable for protecting electrical low voltage systems and terminals in the 40/45 V system. The devices can be used as type surge arresters within the scope of the lightning protection zone concept at zone transition 0B and higher. The high nominal discharge capability of 0 ka makes it possible for the equipment to have a longer service life in comparison to the minimum requirements of the standard. The devices consist of a basic unit and pluggable protection modules, which can be removed extremely easily to carry out insulation measurement. They are fully compatible with SMISSLINE installation devices and the surge arresters in the ABB System pro M model series. The surge arresters are tested as type arresters in accordance with the EN/IEC 6643- test standard. CCC459Z000 CCC4590Z000 CCC459Z000 CCC4590Z000 Mounting Installation and electrical connection The over voltage protection device OVR will be installed near the front of the protected consumers conditioning. The surge arrester is to be mounted right after the Incoming block of the socket system. The OVR404 is snapped directly onto the SMISSLINE bus bar system. /4 CCC45059C003 ABB Technical catalogue SMISSLINE TP
OVR T OVR T OVR T OVR T OVR T OVR T OVR T OVR T OVR T OVR T OVR T OVR Surge arrester OVR Coordination Coordination of surge protection devices The first over voltage protection device does not provide effective protection for the entire power system. Therefore, a coordination of the over voltage protection devices with each other is required. Configuration 5 ka Ip 50 ka Configuration 7 ka Ip 5 ka L L L3 N PEN L L L3 N PEN Main distribution board E933/5* OVR T 3L 5-55 TS E933/5* 3 x OVR T + 5-55 TS or OVR T+ 3L 5-55 TS > 0 meters cable > 0 meters cable Sub-distribution board S 800-5* S 800-5* OVR T 3N 40-75s P TS QS OVR T 3N 40-75s P TS QS > 0 meters cable > 0 meters cable S 800-5* Distribution outlet OVR T N 40-75s P TS QS OVR Plus N 40 ABB Technical catalogue SMISSLINE TP CCC45059C003 /43
Surge and lightning protection solutions Products Standards, IEC 6643 The New IEC 6643-:0 is similar to the EN 6643-:0 and are the standards for Low-Voltage Surge Protective Devices. These standards exist since the nineties and have gone through different releases improving them. In the last release not only the evaluation of the product performances is under focus, but the stress on safety evaluation. Regarding performances, this new edition recognizes the possibility to evaluate and certify a SPD under multiple categories, option not considered in the previous editions. So in order to certify an SPD under the Type and Type category, two different tests need to be performed to validate the features under each one of them. What's new in IEC/EN 6643-:0? New test procedure which takes into account the failure behavior of protective equipment in the event of an overload, or when the service life has expired The Type operating duty test is conducted with a higher current than that specified in the previous standard Recognition of the mixed types, as Type + and Type +3, this allows as to certify the product with more than one category. Until now, the safety of the SPD was verified reproducing situations that represent the working conditions of the SPD, as for example, the short-circuit test or the temporary over-voltage test. According to the new edition of the standard, new tests reproducing the potential interruption of the Neutral conductor and the different modes of end of life of the SPD are performed. These two additional tests are a real Plus on safety management and they are a guarantee for the final user that the installation will not suffer any stress in case of the end of life of the SPD. The new QuickSafe range has been specially developed to answer to these new requirements. All this reducing the stress on the back-up protection device. The new QuickSafe technology allows to comply with the end of life tests thanks to a patented internal disconnection system, this systems disconnects the internal circuit before the internal components (MOVs) go into short-circuit. The advantage for the customer is that the product is selfprotected up to higher values of current and this allows to install back-up protection elements with higher rated current, as these elements will only intervene in the rear case of a short-circuit on site together with a sudden End of Life of the SPD (this happens when for example the SPD is hit by a current higher than it's Imax). You will find the tables on page 8 indicating the maximum back-up rated current MCB or fuse to use to guarantee the coordination. This new technology allows as well to increase the prospective withstand short-circuit current at the point of the installation up to Isccr = 00 ka with a back up protection of maximum rated current of 5 A (for OVR T QS and OVR T-T3 QS) and 60 A (for OVR T-Ts QS and OVR Ts QS). In simple words, the new OVR QuickSafe can be used in 99.9 % of standard installations and becomes an easy replacement to any other SPD ranges. Thermal Disconnection Temperatures measured at the disconnection point of the MOV Temperature ( C) 0 00 90 80 70 60 50 40 30 5 ma 0 ma 5 ma 30 ma 0 ma 0 0 0 5 0 5 0 5 30 35 40 45 50 55 60 65 70 75 80 85 90 95 Pro M (non QuickSafe ) Time (min) QuickSafe Current level Here we can see different curves representing the behavior of the actual range (blue curve ) and the new QuickSafe range (red curve ), for the same level of current (the green line represent the evolution of the current with the time, as specified by the IEC 6643-). These curves represent the temperature INCREASE that the MOV suffers when being tested under these values of current for the indicated time. These are NOT absolute temperature, but relatives ones As you can see with the black arrows, the time to guarantee the disconnection fo the same level of current has been reduced by 6 minutes And even better, as you can see with the orange arrows, the maximum reached temperature required to guarantee the disconnection is lower, from 08 to 76 C. 30 8 6 4 0 8 6 4 Runaway current (ma) /44 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Surge and lightning protection solutions QuickSafe technology In case of an end of life of an MOV in normal conditions, the current passing through the MOV increases progressively creating a quick temperature increase. This phenomenon will slowly damage the MOV itself until it gets into shortcircuit. This phenomenon is called a thermal runaway. In order to avoid such thermal runaway we have added a thermal disconnection that will detect this temperature increase and will open the circuit. This disconnection QuickSafe is directly welded into the surface of the MOV to allow a very fast detection of the raise of temperature, it will react opening the circuit when the temperature achieve the levels considered hazardous for the installation. This disconnection is guaranteed by a metallic arm linked to a spring guaranteeing a quick disconnection. This is a phenomenon that happens only after thousands of surge protection interventions in average. Most of SPDs get changed during the installation updates before this ever happens. This is the ultimate protection at the very end of life of the SPD. 3 4 Here the disconnection system in Close position. During the test simulating and end of life of the SPD, the SPD has to bear a high voltage that forces a current passing through it. In this example, the passing current is 0 A. Few seconds later, the MOV achieves a temperature that is high enough to melt the special metallic alloy that guarantees the contact and the mechanical position of the metallic arm. This releases the metallic arm pushed far away by the junction spring. The tension in the spring is enough to quickly push up the arm and guarantee the insulation of the MOV. The speed of this movement is a key feature to interrupt the electric arc that will appear between the MOV core and the metallic arm. This movement combined with the characteristics of the MOV will guarantee the complete extinction of the arc. At the end of this movement, the metallic arm will stop without any bouncing. There is no risk of a new electric arc development. At this moment, the MOV has not suffered any thermal runaway, so it is not in short-circuit. The distance between between the MOV electrode and the metallic arm guarantees an insulation voltage of over 6000 V, avoiding any risks for the installation. ABB Technical catalogue SMISSLINE TP CCC45059C003 /45
Surge and lightning protection solutions Selection of surge protective devices End of life indicator of the standard surge protective device This option enables indication of the surge protective device state via a mechanical indicator which changes from green to red as the surge protective device comes to end-of-life. When this occurs, the surge protective device must be changed as protection is no longer guaranteed. Technical features of the integrated auxiliary contact Contacts information: Normally-opened (NO)/Normally-closed (NC) Min. load: V DC 0 ma Max. load: 50 V AC A Connection cross-section:.5 mm². Pluggable The pluggable feature of ABB surge protective devices facilitates maintenance. Should one or more worn cartridges need to be replaced, the electrical circuit does not have to be isolated nor do the wires have to be removed. End-of-life indicator standard SPD Normal Red Replace End-of-life NOTE: A faulty surge protective device does not interrupt continuity of service (if wired such that priority is given to continuity of service), it simply disconnects itself. But, the equipment is no longer protected. NOTE: Pluggable surge protective device cartridges have a foolproof system (Neutral cartridges different to Phase cartridges) preventing incorrect operations when replacing a cartridge. Auxiliary contact (TS) This function, achieved by wiring a 3-point A volt-free contact, enables the operational state of the surge protective device to be checked remotely (maintenance premises). For standard products, the TS changes status when the cartridge needs to be replace, protection is not guaranteed. On products fitting the Safety Reserve (s) system, it indicates that one component of the cartridge is damaged, but the protection is still guaranteed. Wiring schematic Surge protective device fitted with the auxiliary contact option OVR404 3N 40-75 P TS QS QuickSafe technology TS: Auxiliary contact P: pluggable device (Cartriges) Max. operating voltage Uc Max. discharge current Imax (8/0) 40kA No. of poles: 4 Phases: 3N 3phases neutral; for TT and TN-S net 4L 4 poles; for TN-S net /46 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Surge arrester OVR Technical data Typ OVR404 4L 40-75 P TS QS OVR404 3N 40-75 P TS QS Technologie varistor Varistor/gaz tube (N) System network TNS TT TNS Electrical features Standard IEC 6643-/EN 6643- IEC 6643-/EN 6643- Type / test class Type Type Number of pole 4 4 Nominal voltage UN (L-N, L-L) 40/45 V 40/45 V Type of voltage a. c. 45 65 Hz a. c. 45 65 Hz Max. cont. operating voltage Uc 75 V AC 75 V AC Nominal discharge current In (8/0) 0 ka 0 ka Maximum discharge current Imax (8/0) 40 ka 40 ka Maximum impulse current Iimp (0/350) kv ka Voltage protection level Up at In (L-N / N-PE / L-PE).5 kv.5/.4/.5 kv Voltage protection level Up at 3 ka (L-N / N-PE / L-PE) 0.5 kv 0.8/.4/0.85 kv Voltage protection level Up at 5 ka (L-N / N-PE / L-PE) 0.7 kv 0.85/.4/0.95 kv Voltage protection level Up at 0 ka (L-N / N-PE / L-PE) 0.9 kv /.4/.5 kv TOV (Temporary overvoltage) withstand Ut (L-N: 5s./N-PE: 00 ms) 337/- V 337/00 V Response time Response time 5 ns 5 ns Short-circuit withstand capability Isccr 00 ka 00 ka Back up prootection circuit breaker 5 A; S800S B 5 A; S800S B Pluggable cartridge Yes Yes Integrated QuickSafe technology Yes Yes State indicator Yes Yes Auxiliary contact (TS) Yes Yes Installation Wire range (L, N, PE).5 5 mm² cable or rope.5 5 mm² cable or rope Connection cross-section.5 6 mm² litz wire with ferrule.5 6 mm² litz wire with ferrule Tightening torque.8 Nm.8 Nm Auxiliary contact (TS) Contacts information NO NC NO NC Max. load/current V DC 0 ma V DC 0 ma Min. load/current 50 V AC A 50 V AC A.5 mm².5 mm² Operating temperature 5 C +60 C 5 C +60 C Stocking temperature 5 C +80 C 5 C +80 C Back up protection Typ QuickSafe Surge Protective Devices Prospective short circuit current at SPD location (Ip) Circuit breaker maximum ratings ) curve B or C Fuse ) (gl - gg) Maximum ratings In: 5, 0, 30 ka 0,65 ka < Ip < 00 ka S800S B or C 5 A ) 5 A fuse Uc: 75, 350, 440, 600 V ) Maximum ratings, must be in accordance with the installation to follow coordination rules with main or upstream short circuit protection(s). ) up to Ip 50 ka ABB Technical catalogue SMISSLINE TP CCC45059C003 /47
Auxiliary switches and signal contacts Description, Technical data 3 4 CCC4509Z000 CCC4509F000 CCC450F000 CCC457F000 General The auxiliary switches and signal contacts are snapped on to the left of the protective devices. On the miniature circuit breakers an optional mounting on the right is also possible. For auxiliary switches and signal contacts supplied via SMISSLINE auxiliary busbars LA or LB a version with integrated contacting pieces is available Conventional supply via the terminals of the auxiliary devices is possible. Function The auxiliary switch works in the same way as the main contacts. The signal contact only operates when the protective device trips. This can be simulated with the white test button. Each time the signal contact is tripped, it must be reset to its starting position using the orange-coloured reset button. Auxiliary switch and signal contacts have special contacts whitch ensure high switching reliability even in systems with low voltages or low currents (PLC, signal systems etc.). 3 4 CCC4509Z000 3 4 CCC4509Z000 Auxiliary switch contacts operate at the same time as the contacts of the protective device (activated manually or automatically). Normally open contact NO (normally open) Normally open contact 3 4 joint operation with protective device CCC456F000 NC (normally close) opposing operation with protective device Signal contacts only operate when the protective device is tripped electrically as a result of a short-circuit, a fault current or overcurrent (undervoltage for MS35). 97 05 98 06 CCC4503Z000 Normally open contact NO (normally open) 97 98 closes during automatic trip Normally closed contact 05 NC (normally close) 06 opens during automatic trip 97 98 CCC45030Z000 CCC45F000 97 98 CCC45030Z000 CCC45F000 Technical data for auxiliary switch and signal contact Signal contact Auxiliary switch SK400 HK400 Rated voltage Un: 400 V 400 V Rated impulse withstand voltage: 4 kv 4 kv Rated current: Ith: 6 A 6 A AC5 A/30 V / A/400 V A/30 V / A/400 V DC3 0.55 A/5 V= 0.55 A/5 V= DC3 0.7 A/50 V= 0.7 A/50 V= Minimum current/voltage: 0 ma V= 0 ma V= (to ensure reliable electrical operation) Connection cross-sections: x.5 mm strand with sleeve x.5 mm strand with sleeve Plastic parts: Free of halogen und cadmium Free of halogen und cadmium Internal resistance Ri: 0.0065 Ω 0.0065 Ω Power loss at rated current Pv: 0.4 W 0.4 W Ambient temperature: Tmax. +55 ºC Tmin 5 ºC Tmax. +55 ºC Tmin 5 ºC Tightening torque: Nm Nm /48 CCC45059C003 ABB Technical catalogue SMISSLINE TP
T T 4 6 Accessory mounting Options for protective devices SK HK AS400 / ZLS93 HK / HK, SK F4C-CM F4C-ARI HK / HK, SK AS400 / ZLS93 HK SK SK HK AS400 / ZLS93 HK / HK, SK NT40 ZLS78 NT40 SC-A/A T N F404 HK AS400 / ZLS93 HK F4C-CM F4C-ARI HK / HK, SK AS400 / ZLS93 HK SK L S400 SK HK AS400 / ZLS93 HK / HK, SK T T IS404 N L T F40 FS403 N SBH / SBS, SBH ZLS930 SBH SBS0 / SBS0 HK / HK, SK ZLS933 HK SK On each protective device can be mounted: auxiliary switch or signal contact or auxiliary contact switches or auxiliary switch and signal contact L 0 3 L 5 L3 T MS35 L T FS45 Contact description signal contact 97 05 97 07 95 05 98 06 98 08 96 06 SK400 SK4000 SK4000 CCC4509Z000 Contact description auxiliary switch 3 4 3 4 3 4 CCC45093Z000 If you use an auxiliary switch and a signal contact you must connect first the signal contact on the MS35 ABB Technical catalogue SMISSLINE TP CCC45059C003 /49
Auxiliary switches and signal contacts Wiring variants. Wiring without auxiliary busbars LA, LB Wiring of auxiliary switch and signal contact blocks without contact to the auxiliary busbars LA and LB.. Input contacts the auxiliary busbars LA, LB. Standard output wiring. 3. Collective alarm, signal contact contacts the auxiliary busbars LA, LB A cost-effective collective alarm solution can be implemented without additional wiring by using this arrangement. Contact description signal contact 97 98 CCC45079F000 CCC45077F000 CCC4583F000 05 06 97 98 07 08 95 96 05 06 CCC4509Z000 Contact description auxillary contact 3 4 3 4 3 4 CCC45093Z000 /50 CCC45059C003 ABB Technical catalogue SMISSLINE TP
Auxiliary switches and signal contacts Contact arrangements to auxiliary busbars CCC4536F000 Left/right mounting of auxiliary switch/signal contact for miniature circuit breaker Space-saving on the socket system By mounting the auxiliary switches/signal contacts alternately on the left and right, the installation width on the SMISSLINE socket system can be reduced. A dummy housing is therefore not needed when just using auxiliary switches or signal contacts. S400 miniature circuit breakers with auxiliary switches mounted on left and right: 5% space saving S400 miniature circuit breakers with NT4063 9 mm on the right and S400 with auxiliary switch on the left: 0% space saving CCC4570F000 Supply options for auxiliary busbars LA and LB CCC458F000 CCC458F000 CCC45809F000 CCC45098F000 Supply option for auxiliary busbars using incoming terminal block. Supply option for auxiliary busbars using incoming terminal block. Positioning of contacting piece ZLS63 on auxiliary switch and signal contact The small auxiliary switch/signal contact contacting piece can be simply and quickly changed from the position of the LA to the LB auxiliary busbar by reversing it by 80 degree. HK/SK NO, NC Signal or auxilary contact Collective alarm LA LB N L L L3 LA LB N L L L3 CCC4563F000 ABB Technical catalogue SMISSLINE TP CCC45059C003 /5
S4C-CM motor operating devices Specific features On the front of the device there is a moveable element for allowing or locking out remote commands. This element may be used when performing maintenance with the residual current circuit breaker in the OFF position, in order to avoid remote-activated closing operations. The operation can be performed via an impulse command. Manual operation is performed by moving the motorized command lever which, in the absence of an operation, allows the circuit breaker lever to be freely moved. The lower section of the device contains an integrated NO+NC auxiliary change-over contact, which indicates the position of the contacts of the associated circuit breaker. The red LED on the front of the device gives a local visual indication of the intervention of the associated device. /5 CCC45059C003 ABB Technical catalogue SMISSLINE TP
F4C-CM motor operating devices Technical specifications Supply voltage:... 30 V AC + 0 % 5 % (50 60 Hz);... 48 V DC + 0 % 5 % F400 F4C-CM Insulation voltage: 500 V for minute Power consumption: V AC < 5 VA 4 V AC < VA 30 V AC < 5 VA... 48 V DC < 0 VA Power consumption at rest:,5 VA Remote command*: via free voltage contacts Closing time at ambient temperature: second Opening time at ambient temperature: 0,5 seconds Delay time for remote resetting after opening due to fault: 8 seconds Number of operations: 0 000 Operating temperature: 5 C + 55 C Storage temperature: 40 C + 70 C Fixing: on EN 6075 rails (35 mm) with rapid fixing system Protection degree (EN 6059): terminals: IPX housing: IP4X Cables length of control circuit: 500 m Cable cross-section:,5 mm Auxiliary contact (terminals 6, 7, 8): Rated current: Command terminals: NO + +NC change-over 3 A (50 V AC), resistive load terminal 9 = closing contact terminal 0 = opening contact terminal = common reference for control contacts + 5 V DC (supplied by motor operating device) * ) After powering up the device, wait 5 seconds before activating the command functions. ) After opening due to a fault, wait 8 seconds before performing the remote resetting. Wiring diagrams for F4C-ARI motor operating devices Use at 30 V AC via a TM5/ bell transformer Low voltage use: 30 V AC, 48 V DC N L LOCKED STATE N L LOCKED STATE -30 V AC -48 V DC 3 4 5 3 4 5 LOCKED 5 6 7 8 LOCKED TM5/ AUX 3 4 AUX OFF ON 6 7 8 9 0 MAX 500m open closed / reset 30 V AC OFF ON 6 7 8 9 0 MAX 500m open closed / reset ABB Technical catalogue SMISSLINE TP CCC45059C003 /53
F4C-ARI auto-reclosing unit Specific features The F4C-ARI auto-reclosing device, installed to the right side of the residual current circuit breakers, automatically performs three reclosing attempts in the event of a fault. If the result of the three reclosing attempts is negative, the device enters a locked state. The luminous two- colors red/green LED shows the operating state of the auto-reclosing device. Blinking green LED: this is displayed for five seconds after the device is powered up. When the LED stops blinking, the device is ready to operate. Steady green LED: the remote control is activated and the device is powered. LED is off: no power supply. Blinking red LED: reclosing cycle in progress. Steady red LED: the remote control is excluded on the device or is in a locked state following three unsuccessful reclosing attempts, or as a result of a remote opening command. The associated residual current circuit breaker can be remotely opened via a command with the NO contact. The remote open command locks out the resetting logic and brings the auto-reclosing device into a locked state. Operation of the close/reset and open commands can be performed via an impulse command. Remote commands and reclosing logic may be deactivated locally by means of the mobile element on the front of the device. This is desirable during maintenance interventions with the device in the OFF position, in order to avoid remoteactivated closing operations or automatic reclosing. In this case, with the selector and the circuit breaker in the OFF position, the device may be physically locked by threading a padlock through the with draw able element on the front. The lower section of the device contains an integrated NO+NC auxiliary change-over contact, which indicates the position of the contacts of the associated circuit breaker. The locked state can be reset: locally, by manually moving the mobile element on the front of the device to the OFF position and subsequently to the ON position. The device will reset and automatically reclose the circuit breaker; remotely, by means of a close command (NO contact) which resets the device and close the circuit breaker. Using both of the resetting methods, the cycle of three reclosing attempts can be repeated. /54 CCC45059C003 ABB Technical catalogue SMISSLINE TP
F4C-ARI motor operating devices Technical specifications Supply voltage:... 30 V AC + 0 % 5 % (50 60 Hz);... 48 V DC + 0 % 5 % Number of automatic reclosing attempts: 3 F400 F4C-ARI Counter reset time: 6 seconds Insulation voltage: 500 V for minute Power consumption: V AC < 5 VA 4 V AC < VA 30 V AC < 5 VA... 48 V DC < 0 VA Power consumption at rest:,5 VA Delay time for activation of automatic reclosing: 3 seconds Reclosing time at ambient temperature: second Opening time at ambient temperature: 0,5 seconds Number of operations: 0 000 Operating temperature: 5 C + 55 C Storage temperature: 40 C + 70 C Fixing on EN 6075 rails (35 mm) with rapid fi xing system Protection degree (EN 6059): terminals: IPX housing: P4X Cables length of control circuit: 500 m Cable cross-section:,5 mm Auxiliary contact (terminals 6, 7, 8): Rated current: Remote command*: Command terminals: change-over 3 A (50 V AC), resistive load via dry contacts terminal 9 = contact for closing and for remote reset of locked state terminal 0 = opening contact terminal = common reference for control contacts, + 5 V DC (supplied by motor operating device) * After powering up the device, wait 5 seconds before activating the command functions. Wiring diagrams for F4C-ARI motor operating devices Low voltage use of several motor operating devices:... 30 V AC,... 48 V DC Use of several motor operating devices at 30 V AC via a single safety transformer -48 V DC -30 V AC 30 V AC 3 4 5 3 4 5 3 4 5 3 4 5 3 4 5 3 4 5 LOCKED LOCKED LOCKED LOCKED LOCKED LOCKED AUX AUX AUX AUX AUX AUX 6 7 8 9 0 6 7 8 9 0 6 7 8 9 0 6 7 8 9 0 6 7 8 9 0 6 7 8 9 0 open closed / reset open closed / reset open closed / reset n... closed / reset open closed / reset open n... closed / reset open ABB Technical catalogue SMISSLINE TP CCC45059C003 /55
Shunt trip for S400 Shunt trips Function: remote opening of the device when a voltage is applied suitable for MCB S400. CCC4568F000 C C C C CCC457Z000 Shunt trip SC-A SC-A Rated voltage AC V... 60 0... 45 DC V... 60 0... 50 Max. release duration ms < 0 < 0 Min. release voltage AC V 7 55 DC V 0 80 Consumption on release Ub V DC AC 4 DC 4 AC 60 DC 60 AC 0 DC 0 AC 0 DC 30 AC 45 AC lb max A..5 4.5 5 4 8.8 0.35 0.5..0.7 Coil resistance 3.7 5 Terminals mm 6 6 Tightening torque Nm Dimensions (H x D x W) mm 00 x 69 x 7.5 00 x 69 x 7.5 /56 CCC45059C003 ABB Technical catalogue SMISSLINE TP
CMS Current Measurement System A system full of benefits Current measurement in power distribution units has never been so compact and perfectly integrated. It is finally possible to monitor the individual circuits of an installation. Measuring current close to electrical loads creates a completely new level of transparency. The CMS sets the standard both in transparency and in user-friendliness. Installation is very simple and the intuitive way you can navigate through the menus ensures that commissioning is genuinely rapid. Integration in perfection It is invaluable but often underestimated: perfect integration in power distribution units. The CMS adjusts to the existing installation architecture like no other system. There are no tangled cables, no additional housings and no additional DIN rail requirements. This allows you to have a perfect overview of the installation at all times and see all the options for expansion and modification over the long term. ABB Technical catalogue SMISSLINE TP CCC45059C003 /57
CMS Current Measurement System Minimal space requirements Small, smaller, CMS it is an enourmous challenge to locate more compact current sensors. Installation is easy The sensors are mounted in a few easy steps. The connection technology can be installed without special tools and there is no longer any need for expensive conventional cabling. User-friendly commissioning Configuration is easy: The intuitive navigation concept allows the system to be set up on the touch screen. Within minutes, it is ready to start measuring. A sensor for all types of current Whether it is DC, AC or mixed current: CMS sensors record everything and that within a huge measurement range of up to 80A. Always upgradeable and expandable The system can be expanded or modified at any time thanks to its flexible and modular design. Sensors can be installed one-by-one at a later date. Maximum reliability The contact-free measurement method means that potential errors are prevented from the outset. /58 CCC45059C003 ABB Technical catalogue SMISSLINE TP
CMS Current Measurement System Trust is good testing is better Current measurement increases availability The CMS is the perfect solution for areas where high system availability is required. This includes industrial facilities, banks, insurance companies or public buildings such as hospitals or airports, which depend heavily on their electronic systems operating smoothly. Failures here lead to major financial losses. In the area of renewable energy technology, the sensors can also help to ensure that systems run smoothly, for example, by monitoring string-level current in solar power systems or testing generators in wind turbines and hydroelectric power plants. The CMS offers the perfect services in numerous industries. Early detection of deviations The CMS measures currents directly in the final circuit and can therefore ensure the error-free operation of a system: continual measurement in the final circuit detects potential hazards, like failures, power drops or other abnormal behaviour, before major damage is caused. I t Overload warning system Constant measurement of current flow in overcurrent protection devices can monitor whether a cable is loaded beyond its nominal current range. Tripping can be prevented before it is too late. I t ABB Technical catalogue SMISSLINE TP CCC45059C003 /59
CMS Current Measurement System The system at a glance The quality of a current measurement system is determined by the perfect interaction and strength of all of its individual parts. This is where the CMS system from ABB sets the bar high: whether in compact size, technology, measurement results, user-friendliness or flexibility every component and feature of the CMS is optimised perfectly for practical application and function. The sensors are the most important part of the system and their compact size is impressive. The sensors can be easily installed anywhere and they do not cause any problems during installation or commissioning. The next important element of the CMS is the control unit, whose touch screen makes it easy and intuitive to use. This device processes all measurement data, shows measurement values and prepares them for individualised processing. All of the sensors communicate with the control unit over the same connection. This does away with the confusing, starshaped cabling, which is often required for analogue measuring transformers. It also saves time during installation and creates a lot of space in the power distribution unit. /60 CCC45059C003 ABB Technical catalogue SMISSLINE TP
It is also very easy to initialise the sensors. You can assign the desired identifiers to the individual sensors with a few clicks in the control unit. The entire commissioning process only takes a few minutes. Just after you can use all of the measurement functions and show them on the display of the control unit. You can remotely query measurement data via a Modbus interface (RS-485/Modbus RTU). The possibilities for further measurement value transmission and processing are nearly infinite. ABB Technical catalogue SMISSLINE TP CCC45059C003 /6
CMS Current Measurement System Increase transparency Measure to reduce costs Public buildings and industrial facilities have electric meters that measure area by area and they do this in a very blanket way. However, in order to be able to make accurate assessments about where the real energy guzzlers are in the building, you need to take a closer look at power consumption. This is where the CMS offers an uncomplicated yet highly efficient solution: it measures the current in the individual final circuits. These measurement results allow you to precisely trace energy flows and triangulate where electricity consumption is too high. This helps you to use energy more efficiently. Maximum transparency in a building with current measurement in the final circuit e.g., server room e.g., production, manufacturer e.g., air-conditioning, heating, lighting 4 3 4 4 e.g., computers, printers, telephones 4 5 4 CMS-System ( measurement points) Sub-distributors 3 UPS 4 Electric meters 5 Main distributors /6 CCC45059C003 ABB Technical catalogue SMISSLINE TP
CMS Current Measurement System The sensors the heart of the CMS No space wasted here: everything is built into an 8-mm wide unit to enable exact and effective measurements. This means that CMS sensors are among the most compact and high-performance sensors on the market. Small size, huge performance: Whether AC, DC or mixed current, CMS sensors capture all types of current within a measurement range of 0 80 A (TRMS). Even upper sidebands in the signal trace are captured. Every sensor has its own signal processing microprocessor, meaning measurement data is transmitted digitally via the bus interface to the control unit. This reduces cable leads into the distribution units and maximises the security of the transmitted mesurement values. Disruptions like those for analogue data are finally a thing of the past. ABB Technical catalogue SMISSLINE TP CCC45059C003 /63
CMS Current Measurement System Integrating sensors CMS sensors are rapidly mounted on ABB low-voltage protection devices. Thanks to the sophisticated design, you have a perfect, compact and clearly arranged unit in the power distribution unit. The CMS-00PS (80 A), CMS-0PS (40 A) and CMS-0PS (0 A) are designed for ABB pro M compact and SMISSLINE devices with twin terminals. The sensor only needs to be plugged into the rear terminal connection. /64 CCC45059C003 ABB Technical catalogue SMISSLINE TP
CMS Current Measurement System The control unit the information centre The control unit (CMS-600) is a user-friendly interface and is the centre for powering and managing the CMS system. Up to x 3 sensors can be connected to each control unit. 47 identifiers can be set on the device. Thereby it is possible to aquire thousands of measurement points over one bus line. This means the CMS is predestined for use as a highlyefficient measurement system, even in very large, extensively networked installations. Modbus RTU CMS systems CMS-800/CMS-80 Flat cable and connector ABB Technical catalogue SMISSLINE TP CCC45059C003 /65