BUETIN 3-1H JUNE 2016 DeZURIK KGC-BD BI-DIRECTIONA CAST STAINESS STEE KNIFE GATE VAVES TECHNICA SPECIFICATIONS
Materials of Construction Item Description Material A1 Body 304 Stainless Steel, ASTM A3 CF8 316 Stainless Steel, ASTM A3 CF8M 317 Stainless Steel, ASTM A3 CG8M 4-SMO Stainless Steel, ASTM A3 CK3MCuN 2205 Duplex Stainless Steel, ASTM A0 CD3MN Hastelloy C 2, ASTM A494 CW12MW A2 Packing SMP - PTFE Braided Packing to 0 F (260 C) (ph Range 0-14) ASP - Self-Adjusting PTFE Braided Packing with AFAS Fluoroelastomer Cord to 400 F (205 C) (ph Range 0-14) TDP - Dry Service, Dry PTFE Braided Packing with Solid PTFE Cord to 0 F (260 C) (ph Range: 0-14) A3 Gate 304 Stainless Steel, ASTM A240 316 Stainless Steel, ASTM A240 317 Stainless Steel, ASTM A240 17-4 Stainless Steel H900 Heat Treated, ASTM A564 4 - SMO Stainless Steel, ASTM A240 2205 Duplex Stainless Steel, ASTM A2 Hastelloy C 2, ASTM B4 410 Stainless Steel, ASTM A240 A4 Gland Same as body material A5 Screw 304 Stainless Steel A6 Washer 304 Stainless Steel A7 Nut 304 Stainless Steel A9 Anti-Extrusion Guide Glass Filled PTFE A10 Perimeter Seat* CR - Chloroprene to 180 F (83 C) NBR - Acrylonitrile-Butadiene to 180 F (83 C) EPDM - Terpolymer of Ethylene, Propylene and a Diene to 2 F (122 C) FKM - Fluoro Rubber to 400 F (204 C) CRW - Chloroprene, Off White to 140 F (60 C) B1 Handwheel Painted, Cast Iron, ASTM A126 Class B B2 Roll Pin Steel or 420 Stainless Steel B4 Thrust Bearing Oil Impregnated Bronze B5 Sleeve Aluminum Bronze B6 Stem 304 Stainless Steel B7 Steel, ASTM A216 Type WCB 304 Stainless Steel, ASTM A3 CF8 B8 Screw Zinc Plated Steel or 18-8 Stainless Steel B9 Nut Zinc Plated Steel or 18-8 Stainless Steel B10 Clip 304 Stainless Steel B11 Stop Collar 304 Stainless Steel B12 Set Screw Zinc Plated Steel or 18-8 Stainless Steel B23 Data Plate 316 Stainless Steel B24 Pop Rivet 18-8 Stainless Steel B28 Grease Fitting Zinc Plated Steel B29 Screw Zinc Plated Steel or 18-8 Stainless Steel B30 Nut Zinc Plated Steel or 18-8 Stainless Steel B42 Wave Washer 304 Stainless Steel B43 ockout Pin 304 Stainless Steel B44 Pin 18-8 Stainless Steel B45 Cable 316 Stainless Steel B46 Cable Clamp 316 Stainless Steel B47 Spacer 304 Stainless Steel *Seat ring is molded with fully encapsulated 316 Stainless Steel reinforcement insert. AFAS is a registered trademark of the Asahi Glass Co., td. *Patent Pending seat design 2 2016 DeZURIK, Inc.
Selection Shut-Off Capabilities All Resilient Seats Pressure Ratings Bubble Tight to Full Rating 2-2 (-) psi C.W.P. ( kpa) 30- (0-) psi C.W.P ( kpa) Note: s with Chloroprene Off-White seats (CRW) are limited to psi (3 kpa). Contact DeZURIK with service conditions. Applicable Standards DeZURIK KGC-BD Knife Gate s are designed and/or tested to meet the following standards: ASME B16.5 Flanges and Flanged Fittings, ASME 2-2 (-) Conforms to related drilling dimensions ASME 16.47 arge diameter Steel Flanges. Series A. Conforms to 30- (0-) related dimensions Conforms to flanged bolt guides JIS 10; DIN 10 and DIN 16; ISO 05-1/PN10 and 05-2/PN16; BS 44/ International Standards PN10 and BS 44/PN16; and AS 2129 Tables D and E; SANS 1123-0 and SANS 1123-1600 Recommendations for Stainless Steel, Bonnetless, MSS SP-81 Flanged, Wafer Knife Gate s. ASME B16.20 Metallic Gaskets for Pipe Flanges. Conforms to spiralwound gasket dimensions. 2- (-) AWWA C520 AWWA C520 Standard for Knife Gate s. Flow Parameters and Actuator Weights 2" mm mm mm mm 2mm 3mm 5mm 2 2 6mm 2 0mm 0mm Cv* Kv* % Open 330 287 5 655 12 1 2020 1745 20 2380 55 4420 7880 6830 10 9630 13800 11920 18300 158 234 00 29000 200 35400 30600 42180 364 49660 42900 5 49800 66010 74900 64740 94980 82 K** (resistance) Port Area (in 2 /cm 2 ) 3.8 8.3 54 13.5 87 21.1 136 29.4 190 52.7 82.9 535 117 5 144 930 192 1239 246 1585 304 1959 3 2387 442 2854 520 3355 603 30 693 4472 787 77 997 6430 *Cv = Flow in GPM of water at 1 psi pressure drop. Kv = Flow in m3/hr. of water at kpa pressure drop. ** K = The resistance coefficient of the valve. The constant (K) can be used to determine the equivalent length of pipe. = KxD Where = Equivalent length of pipe in feet f K = Resistance coefficient D = Pipe diameter in feet f = Friction factor, related to type of pipe 2" mm mm mm mm 2mm 3mm 5mm 2 2 6mm 2 0mm 0mm Basic 10 5 17 8 24 11 33 15 39 18 65 29 106 48 1 68 195 88 281 382 173 1 232 620 281 730 331 913 414 1106 2 1348 611 1602 727 2265 1027 With Handwheel 20 9 28 13 36 16 52 24 58 26 86 39 144 65 190 86 261 3 159 454 206 586 266 With Chainwheel 32 15 40 18 48 22 67 30 34 101 46 182 83 230 104 280 367 166 4 213 647 293 With Bevel Gear With Cylinder lbs. Kg. 4'' 29 13 40 96 44 109 49 52 144 65 194 88 111 299 136 387 1 494 224 630 286 8 344 877 398 1099 498 1320 599 1496 679 1727 783 2427 1101 4'' 38 17 4'' 45 20 6'' 63 29 4'' 59 27 6'' 77 35 8'' 40 4'' 64 29 6'' 82 37 8'' 94 43 6'' 112 8'' 124 56 8'' 177 80 10'' 223 101 8'' 228 103 10'' 273 124 12'' 312 142 10'' 336 152 12'' 3 171 10'' 418 190 12'' 458 208 14'' 4 229 12'' 2 9 14'' 622 282 12'' 719 326 14'' 7 348 16'' 9 449 12'' 828 3 14'' 879 399 16'' 1099 498 12'' 952 432 14'' 6 456 16'' 1224 555 14'' 1246 565 16'' 19 6 13 714 12'' 1412 640 14'' 2 663 16'' 1643 745 18 828 14'' 16 7 16'' 1887 856 18'' 7 956 12'' 1803 818 14'' 1853 841 16'' 2023 918 2202 999 14'' 2612 5 16'' 2816 7 18'' 3048 1383 20'' 3211 1456 Note: Weights are approximate and do not include crating. Pounds Kilograms 3
ing To order, simply complete the valve order code from information shown. An ordering example is shown for your reference. Style Give valve style code as follows: KGC = Cast Stainless Steel Knife Gate Give valve size code as follows: 2 = 2" (mm) 18 = () 3 = () 20 = () 4 = (mm) 22 = (5mm) 5 = (mm) 24 = 2 () 6 = (mm) 26 = 2 (6mm) 8 = () 28 = 2 (0mm) 10 = (2mm) 30 = (0mm) 12 = () 32 = () 14 = (3mm) 36 = () 16 = () Body Style Give body style code as follows: BD = Bi-Directional with DeZURIK Exclusive Premium Packing System End Connection Give end connection code as follows: F1 = ASME UNC Tapping for Threads F110 = ISO 05/PN10 Drilling F116 = ISO 05/PN16 Drilling F1DA = AS2129 Table D Drilling F1EA = AS2129 Table E Drilling F1UN (1) = ASME UN-8 Tapping for Threads F1S10 = SANS 1123-0 F1S16 = SANS 1123-1600 F1T = ASME Through Bolting F1J1 = JIS 10 Drilling On Application Other end connections available on application. Gate Material (3) Give gate material code as follows: S1 = 304 Stainless Steel (Standard for S1 body material) S2 = 316 Stainless Steel (Standard for S2 body material) S3 = 317 Stainless Steel (Standard for S3 body material) On Application S5 = 17-4 Stainless Steel H900 Heat Treated (Used with S1, S2, & S3 body materials) S6 = 4-SMO Stainless Steel (Used with S6 body material) S8 = 410 Stainless Steel (Used with S1, S2 & S3 body materials) S10 = 2205 Duplex Stainless Steel (Used with S2, S3 OR S10 body materials) HC = Hastelloy C (Used with HC body materials) Seat Material (2) Give seat material code as follows: CR = Chloroprene to 180 F (83 C) NBR = Acrylonitrile-Butadiene to 180 F (83 C) EPDM = Terpolymer of Ethylene, Propylene and a Diene to 2 F (122 C) FKM = Fluoro Rubber to 400 F (204 C) CRW = Chloroprene, Off White to 140 F (60 C) Standard Options Give option code as follows: CMC = Certificate of Material Conformance CRT = Certified Physical and Chemical Test Reports = Optional Coating Notes: (1) Applies to valves () and larger. Flange bolt hole threads are 8 threads per inch in accordance with ASME, API and MSS standards. (2) For high temperature service, the limiting factor in valve selection is the lowest temperature of the packing or seat. (3) Gate material limitations by body material in parentheses. ing Example: KGC,6,BD,F1,S2,ASP,S2-CR*Actuator Body Material Give body material code as follows: S1 = 304 Stainless Steel S2 = 316 Stainless Steel S3 = 317 Stainless Steel On Application HC = Hastelloy C S6 = 4 Stainless Steel S10 = 2205 Duplex Stainless Steel Packing Material Give packing material code as follows: SMP = PTFE Braided Packing to 0 F (260 C) (ph Range 0-14) ASP = Self-Adjusting PTFE Braided Packing with AFAS Fluoroelastomer Cord to 400ºF (205ºC) (ph Range 0-14) TDP = Dry PTFE Braided Packing with Solid PTFE Cord to 0 F (260 C) (ph Range: 0-14) 4
Manual Actuators Handwheel and Chainwheel Actuators All 2- (-) valves can be furnished with handwheel actuators or chainwheel actuators. To order handwheel or chainwheel actuators, add the appropriate order code to the basic valve order code. Refer to information on bevel gear actuators for use on paper stock, slurries or when pressure exceeds limits shown. chain for chainwheel actuators as a separate item. Handwheel Actuator Maximum Pressure 304 SST Differential (S1) psi/kpa 2- -mm MN-HD8-CS MN-HD8-S1 5- - MN-HD12-CS MN-HD12-S1 10-2- MN-HD16-CS MN-HD16-S1 MN-HD20-CS* MN-HD20-S1* 3mm MN-HD20-CS* MN-HD20-S1* MN-HD20-CS* MN-HD20-S1* MN-HD20-CS* MN-HD20-S1* 1 * Bevel gear actuators recommended for paper stocks, slurries, or when pressure exceeds limits shown. ing Example: KGC,6,BD,F1,S2,SMP,S2-CR*MN-HD12-CS Chainwheel Actuator Maximum Pressure 304 SST Differential (S1) psi/kpa 2- -mm MN-CW8-CS MN-CW8-S1 5- - MN-CW12-CS MN-CW12-S1 10-2- MN-CW20-CS MN-CW20-S1 3mm MN-CW20-CS* MN-CW20-S1* MN-CW20-CS* MN-CW20-S1* MN-CW20-CS* MN-CW20-S1* MN-CW30-CS* MN-CW30-S1* * Bevel gear actuators recommended for paper stocks, slurries, or when pressure exceeds limits shown. ing Example: KGC,4,BD,F1,S2,SMP,S2-CR*MN-CW8-S1 Bevel Gear Actuators Bevel gear actuators are available on 3- (80-) valves with handwheel or chainwheel actuators. Bevel gear actuators provide vertical mounting of the handwheel or chainwheel, or can be used where space limitations prohibit the use of a standard handwheel or chainwheel. A mechanical advantage makes large valve operation easier and faster. Bevel Gear Handwheel Actuators Bevel Gear Chainwheel Acutators Maximum Pressure 304 SST Differential (S1) psi/kpa 3-80- MNB-HD12-CS MNB-HD12-S1 20-2 0- MNB-HD16-CS MNB-HD16-S1 26-2 6-0mm MNB-HD30-CS MNB-HD30-S1 30-0- MNB-HD30-CS MNB-HD30-S1 Maximum Pressure 304 SST Differential (S1) psi/kpa 3-80- MNB-CW12-CS MNB-CW12-S1 20-2 0- MNB-CW20-CS MNB-CW20-S1 26-2 6-0mm MNB-CW30-CS MNB-CW30-S1 30-0- MNB-CW30-CS MNB-CW30-S1 ing Example: KGC,14,BD,F1,S2,SMP,S2-CR*MNB-HD12-CS ing Example: KCG,14,BD,F1,S2,SMP,S2-CR*MNB-CW12-CS-90 Actuator mounted at 90 degrees Note: For alternate mounting of bevel gear actuators, add -90, -180 or -2 after the actuator code and as 2nd line information on the order. 5
Manual Actuator Accessories Chain for Chainwheel Actuators as a separate item by giving the correct code and specify required length of chain as second line information. One closing link is supplied with the Chainwheel Actuator. Description ACC*CN102 Steel, Zinc Plated 3/16 ACC*CN103 Galvanized 3/16 ACC*CN106 316 Stainless Steel 3/16 ing Example: ACC*CN102 Chain 12 feet long (366cm) Extension for Handwheel Provides extension of the handwheel or nut to allow remote operation normally from above. The extension includes fittings and extension pipe with handwheel or nut mounted. To order, specify description and extension length from center line of valve to top of handwheel. ockout Device Available on all sizes of handwheel and bevel gear handwheel actuated valves. To order, add a comma and the order code K after the actuator code. ing Example: KGC,14,BD,F1,S2,SMP,S2-CR*MNB-HD12-CS,K Floorstand A floorstand for handwheel actuated valves allows operation from above. Includes floorstand with gate position indicator, handwheel, fittings and extension. To order, specify length from center line of valve to base of floorstand. This dimension must be at least twice the dimension from center line to handwheel. ing Example: KGC,14,BD,F1,S2,SMP,S2-CR*MN-HD20-CS Except with floorstand. Center line of valve to base of floorstand 72 inches (1829mm). ENHD Description Extension for Handwheel ing Example: Handwheel: KGC,14,BD,F1,S2,SMP,S2-CR*MN-HD20-CS,ENHD Center line of valve to top of handwheel 72 inches (1829mm). Cylinder Actuators On-Off Cylinder Actuators DeZURIK cylinder actuators are available with double-acting pneumatic or hydraulic cylinders for on/off service. Supply pressure is 60 or 80 psi (410 or 5 kpa). To order, add the proper code from the table to the valve order code. Specify hydraulic media if other than oil. Actuator Sizing 60 psi (410 kpa) Air Supply Steel 304 SST (CS) (S1) 2 & & CY-PC4-CS CY-PC4-S1 mm 5 & & mm CY-PC4-CS CY-PC6-CS CY-PC4-S1 CY-PC6-S1 Maximum Pressure Differential psi/kpa On/Off Slurries, Paper Stock CY-PC4-CS CY-PC4-S1 CY-PC6-CS CY-PC6-S1 iquids & Gases 6
Cylinder Actuators Actuator Sizing (Continued) 60 psi (410 kpa) Air Supply 2mm 3mm 5mm 2 2 6mm 2 0mm CY-PC6-CS CY-PC18-CS CY-PC18-CS 304 SST (S1) CY-PC6-S1 CY-PC18-S1 CY-PC18-S1 Maximum Pressure Differential psi/kpa On/Off Slurries, Paper Stock 1 iquids & Gases 1034 0mm CY-PC18-CS CY-PC18-CS 304 SST (S1) CY-PC18-S1 CY-PC18-S1 Maximum Pressure Differential psi/kpa On/Off Slurries, Paper Stock 1 172 CY-PC18-CS CY-PC20-CS CY-PC18-S1 CY-PC20-S1 1 iquids & Gases 7 = Not required. Use next smaller actuator. = Not available. Use larger actuator or contact DeZURIK. 7
Cylinder Actuators Actuator Sizing 80 psi (5 kpa) Air Supply 2 & & mm 5 & & mm 2mm 3mm 5mm 2 2 6mm 2 0mm 0mm CY-PC4-CS CY-PC4-CS CY-PC4-CS CY-PC6-CS CY-PC6-CS CY-PC18-CS 304 SST (S1) CY-PC4-S1 CY-PC4-S1 CY-PC4-S1 CY-PC6-S1 CY-PC6-S1 CY-PC18-S1 Maximum Pressure Differential psi/kpa On/Off Slurries, Paper Stock 1 iquids & Gases 1034 = Not required. Use next smaller actuator. = Not available. Use larger actuator or contact DeZURIK. 8
Cylinder Actuator Accessories Air Filter Regulator The DeZURIK Air Filter Regulator is designed to provide clean, accurate air pressure to actuators and positioners. Four-Way Solenoid s Solenoid valves may be ordered mounted and piped as part of a complete valve/actuator assembly or as a separate item. Speed Control s Speed Control s are available for controlling valve opening or closing speed with pneumatic actuators. The speed of operation is adjustable. Position Indicating Switches Mechanical or Proximity Position Indicating Switches are available for use on double-acting cylinder actuators. One switch can be set to indicate open or closed position. Two switches will automatically be set to indicate full open and full closed positions. High-Strength Actuator egs For unsupported horizontal mounting of 3- (80-) valve sizes, High-Strength Actuator egs are available as part of a complete valve and actuator assembly. To order, add the SA code after the actuator code. ing Example (complete valve): KGC,6,BD,F1,S1,SMP,S1-CR*CY-PC6-S1,SA Stem Cover Bellows To protect valve stem from environmental debris, the Stem Cover Bellows may be ordered as part of a complete valve and actuator assembly. To order, add the SCB code to the valve and actuator code. ing Example (complete valve): KGC,6,BD,F1,S1,SMP,S1-CR*CY-PC6-S1,SCB ockout Device Available on all sizes of cylinder actuated valves. To order, add a comma and the order code K after the actuator code. ing Example: KGC,14,BD,F1,S2,SMP,S2-CR*,K Electric Motor Actuators DeZURIK Knife Gate s can be furnished with electric motor actuators including imitorque, Auma, Rotork, E.I.M. and others. When ordering electric motor actuators, specify valve order code, shutoff pressure, service conditions (flowing media and installation direction); type of application (on/off); speed of operation; NEMA rating (4, 7, submersible, etc.); electrical characteristics (voltage and phase); actuator accessories and controls as per specification requirements. 9
Basic with Handwheel Actuator F H J M N 2" mm 1.88 48 4.00 102 14.73 374 12.90 328 3. 95 4. 121 17. 445 14.62 371 mm 22.77 8 16.90 429 mm 5. 24.19 614 19.56 497 mm 5. 140 5. 27.10 688 21.07 535 6. 171 2. 6.38 162 33.60 853 24.65 626 2mm 2. 41.06 1043 9. 241 46.59 3 33.63 854 3mm 10. 267 54. 1386 40.82 1037 11. 298 3. 8.69 221.97 1472 42.38 10 12. 318 3. 9.06 230 67.37 1711 49.69 1262 13. 349 71.00 1803. 1302 Inches Millimeters "N" DIA OPTIONA OCKOUT SHOWN IN UNOCKED POSITION J M TOP OF STEM WHEN VAVE IS IN OPEN POSITION GATE IN OPEN POSITION F H Basic with Chainwheel Actuator F H J M N 2" mm 1.88 48 4.00 102 15.81 402 13.62 346 3. 95 4. 121 18.56 471 15.37 390 mm 22.74 8 17.62 448 mm 5..18 640 12. 324 mm 5. 140 5. 26.83 681 21. 548 12. 324 6. 171 2. 6.38 162 34.58 878.12 638 12. 324 2mm 2. 41.56 1056 30. 781 9. 241 47.29 1201 34.35 872 3mm 10. 267 54. 1386 40.82 1037 11. 298 3. 8.69 221 61.97 14 42.38 10 12. 318 3. 9.06 230 67.37 1711 49.69 1262 13. 349.00 1905. 1302 "N" DIA J M TOP OF STEM WHEN VAVE IS IN OPEN POSITION GATE IN OPEN POSITION F H 10
11 Bevel Gear Chainwheel Actuator P F H J M N Standard & 180 90º & 2 3. 95 4. 121 22.10 561 16.09 409 mm 26.38 6 18.37 467 mm 5. 28.82 732 20. 527 mm 5. 140 5. 32.38 822 22.29 566 6. 171 2. 6.38 162 40.88 1038.84 656 2mm 2. 46. 3 31.54 801 9. 241.26 7 35.16 3 3mm 10. 267 56.82 1443 37.78 960 11. 298 3. 8.69 221 62. 1588 41.47 1053 12. 318 3. 9.06 230 69.95 1777 47.03 1195 13. 349 73.63 18.59 1285 5mm 1 381 77.63 1972 54.58 1386 2 85.60 2174 58. 1488 2 6mm 17.13 435 9. 241 101.00 65 64.49 1638 2 0mm 1 464 10.69 272 104.95 2666 68.37 1737 0mm 19.38 492 11. 286 109.48 2781 73.09 1856 10.43 265 24.05 24 20.88 530 11. 286 113.33 2879.74 1949 10.43 265 24.05 611 2 584 11. 286 123.58 3139 84.59 2149 10.43 265 124.05 265 P F H J M N Standard & 180 90º & 2 3. 95 4. 121 22.10 561 16.09 409 mm 26.38 6 18.37 467 mm 5. 28.82 732 20. 527 mm 5. 140 5. 32.38 822 22.29 566 6. 171 2. 6.38 162 40.88 1038.84 656 2mm 2. 46. 3 31.54 801 9. 241.26 7 35.16 3 3mm 10. 267 56.82 1443 37.78 960 11. 298 3. 8.69 221 62. 1588 41.47 1053 12. 318 3. 9.06 230 69.95 1777 47.03 1195 13. 349 73.63 18.59 1285 * 5mm 1 381 77.63 1972 54.58 1386 2 85.60 2174 58. 1488 * 2 6mm 17.13 435 9. 241 101.00 65 64.49 1638 9.59 24.09 612 2 0mm 1 464 10.69 272 104.95 2666 68.37 1737 9.59 24.09 612 0mm 19.38 492 11. 286 109.48 2781 73.09 1856 9.59 24.09 612 2 584 11. 286 113.33 2879 84.59 2149 9.59 24.09 612 2 584 123.58 3139 84.59 2149 9.59 24.09 612 Bevel Gear Handwheel Actuator Inches Millimeters * Note: "N" dimension on & 2 (0 & ) valves is when actuator is mounted at 90 or 2 M F GATE IN OPEN POSITION H "N" DIA P J M F GATE IN OPEN POSITION H "N" DIA P J
Basic with Cylinder Actuator 2" mm mm mm mm 2mm 3mm 5mm 2 2 6mm 2 0mm 0mm F H J P 1.88 4.00 10.56 48 102 268 3. 4. 12.28 95 121 312 14.56 3 5. 17.00 432 5. 5. 18.56 140 471 6. 2. 6.38 22.06 171 162 560 2. 27. 699 9. 31.13 241 791 10. 33. 267 8 11. 3. 8.69 37.44 298 221 9 12. 3. 9.06 4* 318 230 1092 13. 46.66* 349 5 1.* 381 12 54.54* 1385 17.13 9. 60. 435 241 1530 1 10.69 64.31 464 272 1633 19.38 11. 69.69 492 286 17 20.88 11. 72.69 530 286 1846 2 81.19 584 2062 Inches Millimeters *Note: See chart below for, and 2 valves with CY-PC16 Cylinder sizes. 5mm 2 P 47.31 1202. 12 55.28 1404 2- (-) s Actuator 2" M mm mm mm mm 2mm 3mm 22.26 23.98 26.26 30.64 32.18 5.38 CY-PC4 565 609 667 778 817 137 27.61 3 33.56 39.11 7.88 CY-PC6 1 813 852 993 200 32.38 33.94 39.49 49. 53.19 10. CY-PC8 822 862 3 9 13 267.97 54.59 60.35 64.03 1 CY-PC10 1295 1387 1533 1626 330 54.56 60. 64.38 1 CY-PC12 1386 1542 1635 381 63.68 17.00 CY-PC14 1617 432 H "M" MAX J F P "N" NPT 2 PACES GATE IN OPEN POSITION N 1/4 1/4 18- (4-) s Actuator CY-PC12 CY-PC14 73.94 1878 73.24 1 CY-PC16 77. 1968.81 19.94 1929 5mm 85.52 2172 85.52 2172 8 2083 2.48 2273 88.78 25 87.91 2 CY-PC18 2 2 6mm 0mm 0mm 95.38 2423 95. 2426 95. 2432 101.44 7 101.56 80 101.81 86 108.19 2748 108.31 21 108.56 27 113.82 21 113.94 24.19 2900 CY-PC20.69 3193.81 3196 126.06 3202 126.31 3208 M 1 381 17.00* 432 17.00 432 19.00 483 21.00 533 Inches Millimeters N 3/4 3/4 * M dimension on (0mm) is 14." (3mm) Sales and Service For information about our worldwide locations, approvals, certifications and local representative: Web Site: www.dezurik.com E-Mail: info@dezurik.com 2 Riverside Ave. N. Sartell, Minnesota 56377 Phone: 320-9-2000 Fax: 320-9-2227 DeZURIK, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation. Design features, materials of construction and dimensional data, as described in this bulletin, are provided for your information only and should not be relied upon unless confirmed in writing by DeZURIK, Inc. Certified drawings are available upon request. Printed in the U.S.A.