CARCASS SPLITTING SAW

REV F: 0/ INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. CARCASS SPLITTING SAW TOOL DATA MODEL: BANDMASTER BM-V-SDB w/air ASSEMBY NO. 7000 TYPE: ELECTRICAL / AIR OPERATED NET WEIGHT: 70 LB (77. KG) MOTOR HORSEPOWER: HP / HP MODEL: BANDMASTER BM-V-S with Air ASSEMBLY NO. 70800 TYPE: ELECTRICAL / AIR OPERATED NET WEIGHT: 80 LB (8 KG) MOTOR HORSEPOWER: HP / HP MODEL: BANDMASTER BM-V-SD with Air ASSEMBY NO. 70800 TYPE: ELECTRICAL / AIR OPERATED NET WEIGHT: 70 LB (77. KG) MOTOR HORSEPOWER: HP / HP MODEL: BANDMASTER BM-V-SB with Air ASSEMBLY NO. 7080 TYPE: ELECTRICAL / AIR OPERATED NET WEIGHT: 00 LB (9 KG) MOTOR HORSEPOWER: HP / HP VIBRATION: LESS THAN (<) db <.m/s NOISE: LESS THAN 8dB KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

! WARNING = Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage.! CAUTION = Hazards or unsafe practices which could result in minor personal injury, product or property damage.! NOTICE REV F: 0/ = Important installation, operation or maintenance information. OPERATING AND SAFETY INSTRUCTIONS! WARNING DO NOT OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTOOD THE SAFETY INSTRUCTIONS AND OPERATING MANUALS.! WARNING DO NOT OPERATE THIS TOOL UNTIL YOU HAVE RECEIVED TRAINING IN THE HANDLING, OPERATION AND USE OF THIS TOOL. STOP USING A MALFUNCTIONING OR DEFECTIVE TOOL IMMEDIATELY. REPORT ANY! WARNING PROBLEMS OR DEFECTS TO YOUR SUPERVISOR FOR REMOVAL OF THE TOOL FROM SERVICE.! WARNING DO NOT ATTEMPT TO REPAIR THE TOOL YOURSELF.! WARNING DO NOT ALLOW UNAUTHORIZED PERSONS TO USE TOOL.! WARNING REMOVE AND DISCONNECT POWER FROM THE TOOL WHEN TOOL IS LEFT UNATTENDED OR IS NOT IN USE.! WARNING NEVER TIE DOWN, BYPASS, ALTER OR MODIFY THE ACTIVATING SWITCHES OR TRIGGERS OF THIS TOOL.! WARNING NEVER MAKE ALTERATIONS OR MODIFICATIONS TO THIS TOOL. BE CONSTANTLY AWARE AND ALERT FOR UNSAFE CONDITIONS AND REPORT THEM! WARNING IMMEDIATELY TO YOUR SUPERVISOR. NEVER PLACE YOUR HAND OR ANY PART OF YOUR BODY IN THE CUTTING PATH OF THE! WARNING TOOL. NEVER ALLOW ANYONE ELSE TO PLACE THEIR HANDS OR ANY PART OF THEIR BODY IN THE! WARNING CUTTING PATH OF THE TOOL.! WARNING DO NOT ACTIVATE CONTROL SWITCHES OR TRIGGERS OF THIS TOOL UNLESS YOU INTEND TO TEST OR OPERATE THIS TOOL.! WARNING! CAUTION DO NOT USE THIS TOOL FOR ANY PURPOSE OTHER THAN IT S INTENDED PURPOSE. WHEN OPERATING THIS TOOL WEAR THE PROTECTIVE GEAR AND SAFETY EQUIPMENT SUPPLIED TO YOU.! WARNING THE NOISE EMISSION (SOUND PRESSURE LEVEL) AT THE WORKSTATION MAY EXCEED 80 db (A). EAR AND SOUND PROTECTION GEAR IS REQUIRED. VIBRATION: LESS THAN (<) db <.m/s NOISE: LESS THAN 8dB KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ OPERATING INSTRUCTIONS! WARNING ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL.. TO ENSURE TOOL IS OPERATING PROPERLY, PERFORM FOLLOWING STEPS AT START OF EACH SHIFT: MAKE SURE TOOL MOVES UP AND DOWN FREELY WHILE HANGING FROM BALANCER OVERHEAD. WITH POWER TO TOOL TURNED ON, TEST TRIGGER FOR PROPER OPERATION. DEPRESS EACH TRIGGER SEPARATELY. TOOL SHOULD NOT ACTIVATE. DEPRESS BOTH TRIGGERS. TOOL SHOULD ACTIVATE. IF TOOL HAS "ANTI-TIE DOWN" OPTION, BOTH TRIGGERS MUST BE DEPRESSED SIMULTANEOUSLY FOR TOOL TO ACTIVATE.. TO PERFORM WORK, HOLD TOOL FIRMLY AT BOTH HANDLES. SQUEEZE TRIGGERS TO ACTIVATE TOOL.. START CUT WITH SAW NOSE POINTED UP AT AN ANGLE.. LEVEL SAW TO HORIZONTAL POSITION IN LOIN AREA.. POINT NOSE OF SAW AT DOWNWARD ANGLE IN CHUCK AND NECK AREA.. A BEGINNING SPLITTER CAN MARK BACKFAT OF BEEF WITH A KNIFE TO HELP SAW DOWN CENTER OF BACKBONE AND UNTIL OPERATOR IS FAMILIAR WITH SPLITTING PROCEDURE. 7. DO NOT EXERT EXCESSIVE PRESSURE. ALLOW TIME FOR THE TOOL TO CUT. 8. PUSH SAW FORWARD SO THAT GUARDS, ITEMS AND FIGURE, RIDE AGAINST BEEF. THIS HELPS STEADY SAW IN CUT AND HELPS ELIMINATE BLADE JUMPING AND CHATTERING. 9. TOOL REQUIRES 0 S.C.F.M. OF AIR @ 90 P.S.I. AIR PRESSURE. MAINTENANCE ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE! WARNING AND SERVICE TO THIS TOOL.. TOOL REQUIRES GREASING AFTER 0 HOURS OF OPERATION. GREASE USING KENTMASTER GREASE (PART NO. 790070). BLADE REMOVAL AND CLEANING.! WARNING! WARNING ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR REMOVING BLADE FROM TOOL. ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADE FROM TOOL.. REMOVE PAPER WRAPPER FROM BLADE.. OPEN COVERS, FIGURE, ITEMS,, AND.. INSTALL TORQUE WRENCH, ITEM, INTO, FIGURE, ITEM, AND TURN COUNTER-CLOCKWISE (CCW). THIS ALLOWS TAKE-UP WHEEL AND SLIDE, ITEMS 7 AND 8, TO RETRACT.. SLIDE TAKE-UP WHEEL TO RIGHT.. HOLD BLADE, WITH TEETH FACING AWAY FROM YOU, AND INSTALL INTO SLOT OF BEAM, CONTINUING AROUND AND OVER THE TAKE-UP AND DRIVE WHEELS.. TURN TORQUE WRENCH CLOCKWISE (CW) TO ELIMINATE BLADE SLACK AND TIGHTEN TAKE-UP WHEEL AGAINST BLADE (TORQUE WRENCH IS PRESET AT FACTORY AND WILL SLIP AFTER PLACING PROPER TENSION ON BLADE). 7. TWIST BLADE 90 AT BLADE GUARDS AND INSERT BLADE INTO SLOTS WITH TEETH FACING DOWNWARD. 8. TURN DRIVE WHEEL, ITEM 9, SLOWLY BY HAND, TO CHECK TRACKING OF BLADE ON WHEELS. 9. RETORQUE AGAIN UNTIL TORQUE WRENCH SLIPS. AT END OF EACH SHIFT:. REMOVE SAW BLADE.. IF USING BLADE AGAIN, WASH BLADE WITH HOT WATER TO REMOVE FAT, MEAT AND BONE PARTICLES.. DRY AND APPLY A COAT OF MINERAL OIL TO ENTIRE SURFACE OF BLADE TO AVOID OXIDATION. KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ CLEANING AND STERILIZING SAW AT END OF EACH SHIFT:. REMOVE SAW BLADE.. CLEAN AND WASH DOWN BOTH INSIDE AND OUTSIDE OF ENTIRE MACHINE THOROUGHLY WITH HOT WATER AND CLEANING AGENT. AVOID USING HARSH CAUSTIC CLEANERS ON MACHINE.. WASH OFF ALL BONE DUST AND MEAT PARTICLES FROM INSIDE OF FRAMES, AROUND WHEELS AND GUIDES.. SPRAY BOTH INSIDE AND OUTSIDE OF MACHINE WITH A LIGHT COAT OF MINERAL OIL. WATER CONNECTION A BULKHEAD FITTING, FIGURE, ITEM 0, IS PROVIDED AT THE BASE OF DRIVE SIDE FRAME, ITEM, FOR CONNECTION TO COLD WATER. ADJUST CONNECTOR AND NOZZLE, ITEMS AND, TO CLEAN BONE DUST FROM DRIVE WHEEL AND MEAT PARTICLES TRAPPED BETWEEN TEETH OF SAW BLADE. FITTING AND HOSE, ITEMS AND, AT BASE OF DRIVE SIDE FRAME, ARE PROVIDED FOR DRAINAGE OF WASTE WATER. TORQUE WRENCH CALIBRATION TORQUE WRENCH, ITEM, IS CALIBRATED AND PRESET TO INCH/LBS AT FACTORY. PERIODICALLY CHECK CALIBRATION BY USE OF ANOTHER TORQUE WRENCH WITH A DIAL TO MAKE ADJUSTMENT AND RESET TORQUE WRENCH TO INCH/LBS. REMOVE TORQUE WRENCH COVER TO CLEAN AND LUBRICATE PERIODICALLY. TESTING AND SETTING OF TORQUE WRENCH: TOOLS REQUIRED: HEX WRENCH -- /" HEX BAR -- /", ABOUT "-" LONG HEX SOCKET -- /" WITH DRIVE END TO MATCH COMMERCIAL WRENCH SELECTED TORQUE WRENCH, COMMERCIAL DIAL TYPE PREFERABLE DRIVER -- /8"-7/" FLAT BLADE STEP -- TESTING KENTMASTER TORQUE WRENCH A. ATTACH COMMERCIAL TORQUE WRENCH TO KENTMASTER TORQUE WRENCH USING /" HEX BAR AND /" HEX SOCKET. B. HOLD ASSEMBLY FIRMLY AND ROTATE KENTMASTER TORQUE WRENCH CLOCKWISE SLOWLY UNTIL WRENCH "SLIPS". C. INDICATOR NEEDLE ON COMMERCIAL TORQUE WRENCH SHOULD READ IN/LBS ± IN/LBS (%). IF OVER OR UNDER VALUE, PROCEED TO STEP -- RESETTING KENTMASTER TORQUE WRENCH. STEP -- RESETTING KENTMASTER TORQUE WRENCH A. USING /" HEX WRENCH, REMOVE FOUR () S HOLDING THE WRENCH HANDLE IN PLACE. REMOVE HANDLE AND GASKET. SET ALL PARTS ASIDE FOR REUSE. B. HOLD WRENCH BODY SECURE BY EITHER CLAMPING SMALL DRIVE END IN VISE OR BY CLAMPING THE /" HEX BAR IN VISE AND ATTACHING WRENCH TO BAR. NOTE: Do not clamp body of Torque Wrench in vise as severe damage to Torque Wrench could occur. C. USE FLAT BLADE DRIVER TO ADJUST THE FOUR () SET S UNDER WRENCH HANDLE. USE A STAGGERED PATTERN WHILE ADJUSTING, SUCH AS UPPER, LOWER, LEFT THEN RIGHT. TO REDUCE TORQUE VALUE - BACK OFF SET S COUNTER-CLOCKWISE ABOUT /8 TURN EACH. TO INCREASE TORQUE VALUE - TURN IN SET S CLOCKWISE ABOUT /8 TURN EACH. D. REASSEMBLE TORQUE WRENCH WITH HANDLE AND GASKET. RETEST PER STEP. CONTINUE TESTING AND SETTING UNTIL WRENCH OPERATES AT PROPER TORQUE VALUE. KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ HANGER THE SAW HANGER INCORPORATES TWO () ADJUSTMENT FEATURES. ADJUSTMENT "H" (HORIZONTAL) SHIFTS WEIGHT OF SAW FROM FRONT TO REAR ACCORDING TO OPERATOR PREFERENCE. WEIGHT OF SAW SHOULD BE ADJUSTED SO THAT NOSE OF SAW IS TIPPED DOWN SLIGHTLY FOR BETTER OPERATOR CONTROL. TO ADJUST, LOOSEN TWO () S, ITEMS, AND ADJUST ACCORDINGLY. ADJUSTMENT "V" (VERTICAL) SHIFTS WEIGHT OF SAW FROM RIGHT TO LEFT, AFFECTING BLADE PATH AND STRAIGHTNESS OF CUT. NO ADJUSTMENT SHOULD BE REQUIRED AS MACHINES ARE ADJUSTED AT FACTORY FOR WEIGHT DISTRIBUTION FROM SIDE TO SIDE. IF THERE IS "SOFT-SIDING" OF CARCASS RESULTING FROM BLADE CUTTING TO LEFT OR RIGHT OF CENTERLINE, MAKE ADJUSTMENT AS FOLLOWS: CUTTING EXCESSIVELY TO RIGHT -- WITH A /8" HEX WRENCH, TURN SHAFT, ITEM 7, COUNTER-CLOCKWISE. CUTTING EXCESSIVELY TO LEFT -- WITH A /8" HEX WRENCH, TURN SHAFT, ITEM 7, CLOCKWISE. Figure BM-V- KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ TROUBLE SHOOTING HINTS: BE SURE DRIVE WHEEL IS TURNING COUNTER-CLOCKWISE (CCW) AND BLADE IS INSTALLED WITH TEETH POINTED TOWARD DRIVE FRAME. BE SURE BLADE TEETH ARE SITTING ABOVE UNDERCUT ON BOTH WHEELS SO AS NOT TO AFFECT SET OF TEETH. BAD SPLIT CHECK GAP BETWEEN CARBIDE INSERTS WHICH MUST NOT BE TOO TIGHT OR TOO LOOSE. BLADE SHOULD SLIDE THROUGH WITHOUT PLAY. MAKE ADJUSTMENT IF NECESSARY. UNEVEN SPLIT CUTS TO LEFT OR RIGHT REPLACE SAW BLADE IN CASE BLADE IS DEFECTIVE. ADJUST SAW HANGER (ADJUSTMENT "V") IF SAW CUTS OFF CENTER TO RIGHT OR LEFT. ADJUST HANGER ("H" ADJUSTMENT) IF SAW NOSE RISES TOO EASILY AND ADDITIONAL WEIGHT MUST BE SHIFTED FORWARD. BE SURE SAW IS NOT DROPPING DOWN TOO QUICKLY. ADJUST BALANCER. BLADE OVER OR UNDER TORQUED. CHECK TORQUE WRENCH CALIBRATION. CHECK IF BLADE IS BREAKING AT WELD. BLADE MAY BE DEFECTIVE. PREMATURE BLADE CRACKING OR BREAKING WHEELS SLIPPING IN BLADE (EVIDENT BY VERY SHINY BLADE SURFACE). CHECK FOR INCORRECT TORQUE SETTING. CHECK TORQUE WRENCH CALIBRATION. OPERATOR PUSHING SAW THROUGH BEEF EXCESSIVELY. BLADE OVER OR UNDER TORQUED. CHECK TORQUE WRENCH CALIBRATION. CHECK FOR PROPER GAP (.0"-.08",.-.7mm) BETWEEN CARBIDE INSERTS. CHECK FOR BONE DUST BUILD-UP AT GUIDES. CLEAN OUT AND INCREASE WATER FLOW IF NECESSARY. BLACK APPEARS ON BACKBONE CHECK IF BLADE IS SLIPPING ON WHEELS. LOOK FOR CAUSE AND CORRECT. CHECK FOR PROPER GAP (.0"-.08",.-.7mm) BETWEEN CARBIDE INSERTS. GAP MAY BE TOO TIGHT, CAUSING INSERTS TO MACHINE SIDES OF BLADE. CHECK FOR CHIPPED OR CRACKED CARBIDE INSERTS AT BLADE GUARD ASSEMBLIES. ROTATE OR REPLACE IF NECESSARY. WITH BLADE REMOVED, CHECK TAKE-UP WHEEL TO BE SURE IT SPINS FREELY. CHECK WHEELS FOR PLAY, LOOSENESS OR LOOSE S OR NUTS. CHECK TAKE-UP WHEEL BRACKET, TIGHTEN AND CORRECT PLAY. CHECK WHEEL BEARINGS AND REPLACE IF DEFECTIVE. BLADE SLIPS OFF WHEELS CHECK WHEELS FOR ROUNDNESS AND WEAR. BE SURE WHEEL FACES ARE NOT TAPERED OR HAVE FLAT SPOTS DUE TO WEAR. REPLACE IF DEFECTIVE. CHECK TAKE-UP WHEEL FOR PROPER TORQUE SETTING. LOOK FOR ANY BLADE OBSTRUCTIONS. CHANGE SAW BLADE. BLADE MAY BE DEFECTIVE. KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ REMOVE BLADE FROM MACHINE. BACK OFF, ITEM, WITH TORQUE WRENCH. GRAB TAKE-UP WHEEL WITH BOTH HANDS AND SLIDE BACK AND MOTOR PULLS EXCESSIVE FORTH. IT SHOULD SLIDE FREELY. IF IT BINDS OR TAKES EXCESSIVE EFFORT, AMPERAGE (WITHOUT LOAD) DISASSEMBLE COMPLETELY. CHECK TO SEE IF GIBS LOCATED ON EACH SIDE OR OF SLIDE ARE TOO CLOSE AND TIGHT AGAINST SLIDE. LOOSEN S THAT BLADE IS TOO LOOSE WHILE HOLD GIB IN PLACE. SPREAD GIBS SLIGHTLY OUT AND RETIGHTEN S. TORQUE WRENCH IS SLIDE SHOULD MOVE BACK AND FORTH FREELY, BUT WITHOUT UP AND DOWN PROPERLY CALIBRATED PLAY. REASSEMBLE AND TEST MACHINE. LUBRICATE SURFACES BETWEEN SLIDE AND GIB. SERVICE. KEEP GOOD RECORDS OF ALL SERVICE ACTIVITY AND INCLUDE TOOL IN PREVENTIVE MAINTENANCE PROGRAM.. USE ONLY GENUINE KENTMASTER REPLACEMENT PARTS TO ASSURE PROPER PERFORMANCE OF TOOL.. CONTACT THE KENTMASTER SUPPLIER NEAREST YOU FOR PARTS AND CUSTOMER SERVICE INFORMATION. PARTS BOOK MODELS MAIN ASSEMBLIES KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-7 OF

Figure MODELS BM-V- WITH AIR REV F: 0/

BENDMASTER BM-V- w/air ITEM 7 8 9 0 7 8 9 0 7 REV F: 0/ 7000 BMV-SDB 70800 BM-V-SD 70800 BM-V-S 7080 BM-V-SB OPTIONS OPTIONS OPTIONS 700 7000 7000 7000 70007 700900 00 709790 70897 709890 70990 700 700 7090 700 700 7080 7070 7070 7080 70880 7080 70900 7080 70800 708790 7080 70880 7090 7090 70070 700 70997 7099 7090 700 70998 708 708807 000090 00090 00080 00 000 00 00 HP MOTOR ASSEMBLY HP MOTOR ASSEMBLY HP MOTOR ASSEMBLY POWER SUPPLY, V, ATD, AIR POWER SUPPLY, V, NO ATD, AIR POWER SUPPLY,NON V, ATD, AIR POWER SUPPLY,NON V, NO ATD, AIR POWER SUPPLY, PHASE /0V, AIR TORQUE WRENCH / TOOL WRENCH / TOOL WRENCH, ADJUSTMENT / TOOL EXTERNAL SPRAY ASSEMBLY SPRAY TUBE ASSEMBLY - OPTIONAL SPRAY TUBE ASSEMBLY - OPTIONAL CAP GASKET GEAR, DRIVE /w HP MOTOR 0/0 Hz GEAR, DRIVE /w HP/HP MOTOR 0Hz GEAR, DRIVE /w HP/HP MOTOR 0Hz GEAR, DRIVEN /w HP MOTOR 0/0 Hz GEAR, DRIVEN /w HP/HP MOTOR 0Hz GEAR, DRIVEN /w HP/HP MOTOR 0Hz BEAM BEAM COVER, BEAM -DRIVE SIDE COVER, BEAM - DRIVE SIDE - BM-V-SB COVER, GEAR DRIVE WHEEL ASSEMBLY DRIVE WHEEL ASSEMBLY COVER, BEAM TAKE-UP SIDE FITTING FOR DISCHARGE HOSE FLANGE, FRONT SHAFT - DRIVE NUT, DRIVE WHEEL TAKE-UP SIDE ASSEMBLY - BM-V-SDB TAKE-UP SIDE ASSEMBLY - BM-V-SD TAKE-UP SIDE ASSEMBLY - BM-V-S TAKE-UP SIDE ASSEMBLY - BM-V-SB DRIVE SIDE ASSEMBLY - BM-V-SDB DRIVE SIDE ASSEMBLY - BM-V-SD DRIVE SIDE ASSEMBLY - BM-V-S DRIVE SIDE ASSEMBLY - BM-V-SB LOCKWASHER LOCKNUT BEARING BEARING BLADE - BM-V-SDB BLADE - BM-V-SD BLADE - BM-V-S - - -

8 9 0 7 8 9 0 ITEM 00 BLADE - BM-V-SB 700000 PLUG 7070 WINDOW 70000 DISCHARGE HOSE 780 O-RING 780 O-RING 779870 SEAL 77980 SEAL 800 SET 80700 KEY 900 0 0 0 9080 900 9900 0 0 0 9080 9070 BENDMASTER BM-V- w/air 7000 70800 70800 BMV-SDB BM-V-SD BM-V-S REV F: 0/ 0 0 7080 BM-V-SB Figure BOM FOR MODELS BM-V- WITH AIR DRIVE WHEEL ASSEMBLY ITEM 70800: DRIVE WHEEL ASSEMBLY ASSEMBLY FOR BM-V-SDB,SD,S 7080 WHEEL, DRIVE 7080 INSERT 900 8 ITEM 708790: DRIVE WHEEL ASSEMBLY ASSEMBLY FOR BM-V-SB 708700 WHEEL, DRIVE 7080 INSERT 900 8

REV F: 0/ TAKE-UP SIDE ASSEMBLY Figure TAKE-UP SIDE ASSEMBLY KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

ITEM 7 8 9 0 7 8 9 0 7 8 9 0 700 70990 7070 7070 70970 70780 7090 70790 700 70800 7080 7090 70870 70890 70890 7080 70870 700 7080 7090 70870 70890 70800 708900 700 709090 7090 70900 7080 70880 700 000080 0000 0080 090 090 000 000 7080 900 9080 9900 9900 900 900 9000 9070 900090 TAKE-UP SIDE ASSEMBLY HINGE ASSEMBLY HINGE ASSEMBLY KNOB PLATE PLATE GIB GIB HOLDER, SHAFT HOLDER, SHAFT INSERT, ADJUSTABLE SPACER SPACER SHAFT SLIDE SLIDE WHEEL, TAKE-UP WHEEL, TAKE-UP WHEEL, TAKE-UP, ADJUSTABLE, ADJUSTABLE BLOCK, SLIDE CATCH COVER COVER COVER BLADE GUIDE ASSEMBLY BLADE GUIDE ASSEMBLY FRAME, TAKE-UP SIDE FRAME, TAKE-UP SIDE FRAME, TAKE-UP SIDE FRAME, TAKE-UP SIDE LOCKWASHER LOCKNUT NILOS RING BEARING CUP TAPER BEARING CONE LABEL, DANGER/WARNING RETAINING RING FITTING - LUBE SET SET NUT 700 MODEL BM-V-SDB 70997 MODEL BM-V-SD 7099 MODEL BM-V-S 0 REV F: 0/ 7090 MODEL BM-V-SB 0 TAKE-UP WHEEL ADJUSTMENT TAKE-UP WHEEL, ITEM 0, MUST TURN FREELY BUT WITHOUT EXCESSIVE PLAY OR LOOSENESS. ELIMINATE EXCESSIVE PLAY BY TIGHTENING NUT, ITEM 8, AT CENTAR OF TAKE-UP WHEEL. Figure TAKE-UP SIDE ASSEMBLY BOM KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ DRIVE SIDE ASSEMBLY - AIR Figure DRIVE SIDE ASSEMBLY - AIR KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

ITEM 7 8 9 0 7 8 9 0 7 8 9 0 7 8 9 0 DRIVE SIDE ASSEMBLY, AIR 700 70998 708 BM-V-SDB BM-V-SD BM-V-S 700 700 700 700 7070 7097 7080 70880 7080 70890 70890 708780 70880 7090 70900 709 70980 70990 70977 70977 700 70 700 700 0000 0000 0000 00900 000 000 70070 7000 70000 700 700 700 70070 70090 700 700 7080 800 90000 90900 90 9900 9900 900 HINGE ASSEMBLY HINGE ASSEMBLY SPACER, HINGE SPACER, HINGE KNOB FRAME, DRIVE SIDE FRAME, DRIVE SIDE FRAME, DRIVE SIDE FLANGE, REAR CATCH COVER, DRIVE SIDE COVER, DRIVE SIDE REAR HANDLE ASSEMBLY BLADE GUIDE ASSEMBLY BLADE GUIDE ASSEMBLY TUBE AIR SWITCH ASSEMBLY AIR SWITCH ASSEMBLY HANGER ASSEMBLY - SHORT HANGER ASSEMBLY - LONG TUBE TUBE AIR HANDLE ASSEMBLY ELBOW ON-OFF PLATE BOOT, TOGGLE SWITCH ON/OFF SWITCH SWITCH AIR / ELECTRIC LABEL, ELECTRIC WARNING RETAINING RING BULKHEAD COUPLING PIPE BUSHING TEE CONNECTOR CONNECTOR SPRAY NOZLE MALE PLUG SOCKET CONNECTOR ELBOW UNION DOWEL PIN REV F: 0/ 708807 BM-V-SB KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

ITEM 900 9000 SET 900090 NUT DRIVE SIDE ASSEMBLY, AIR 700 70998 708 BM-V-SDB BM-V-SD BM-V-S REV F: 0/ 708807 BM-V-SB Figure 7 BOM FOR DRIVE SIDE ASSEMBLY WITH AIR TRANSMISSION REFERENCE: MODEL BM-V- FIGURE Figure 8 TRANSMISSION OVERVIEW TRANSMISSION AND SPEED REDUCTION GEARS ARE LOCATED BEHIND DRIVE WHEEL AND CAN BE SERVICED BY OPENING DRIVE WHEEL COVER. A ROUND GLASS SIGHT GAGE IS LOCATED BEHIND DRIVE WHEEL AND CAN BE VIEWED WITHOUT WHEEL REMOVAL. A PLUG IS LOCATED BELOW THE SIGHT GAGE FOR DRAINING AND ANOTHER ABOVE FOR FILLING WITH OIL. PERIODICALLY CHECK OIL LEVEL AND ADD OIL IF LEVEL BELOW SIGHT GAGE WITH SAW IN HORIZONTAL POSITION. IF OIL LOOKS CONTAMINATED WITH WATER, GRITTY OR BROKEN DOWN, DRAIN AND REFILL TO ABOVE SIGHT GAGE WITH HIGH QUALITY GEAR LUBRICANT. WE RECOMMEND MOBILUBE HD 80W-90 SAE 80W-90 GEAR LUBRICANT, MULTI-PURPOSE. TRANSMISSION SHOULD BE FLUSHED OUT AND REFILLED AFTER EVERY 00 HOURS OF OPERATION, AND WHEN OPENED UP FOR MAINTENANCE. THE GEAR LUBRICANT USED SHOULD ALSO BE USED FOR FLUSHING OUT TRANSMISSION. KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ BLADE GUIDE ASSEMBLY, TAKE-UP SIDE 709090: BLADE GUIDE ASSEMBLY, FRONT ITEM 7 8 9 0 7080 7080 7080 7090 8800 88900 900 900 9900 900 900 98700 GUIDE HOLDER REAR GUARD FRONT GUARD GUIDE CARBID INSERT BALL PLUNGER NUT PIN 7 Figure 9 BLADE GUIDE ASSEMBLY, FRONT (BM-V-S & SB) KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ BLADE GUARD ADJUSTMENTS BLADE GUARD CONSISTS OF TWO () CARBIDE INSERTS, ITEM FIGURE 9, THROUGH WHICH THE BLADE PASSES, AND A BACK-UP INSERT LOCATED JUST ABOVE THE BLADE. THE INSERTS SHOULD BE CLEANED DAILY AND INSPECTED PERIODICALLY FOR WEAR AND PROPER GAP WIDTH. THE INSERTS MAY BE ROTATED UNTIL ALL FOUR () SIDES ARE WORN, AND THEN TURNED OVER FOR AN ADDITONAL FOUR () SIDES. THE BACK-UP INSERT SHOULD BE ROTATED WHEN A GROOVE IS WORN INTO IT OR WEAR IS APPARENT. GAP ADJUSTMENT:. REMOVE FOUR () S, ITEM 9, FIGURE 9.. CLEAN, LUBRICATE AND ROTATE OR REPLACE INSERTS. THERE ARE TWO () FIBER GUIDES, ITEM, LOCATED UNDER INSERTS. THEY HELP KEEP BLADE FROM BEING PULLED OUT OF GAP. REPLACE GUIDES IF EXCESSIVELY WORN. WITH SAW IN FREE RUNNING CONDITION, CHECK BLADE'S VERTICAL LOCATION BETWEEN INSERTS. PROPER LOCATION IS TOP OF BLADE JUST TOUCHING BACK-UP INSERT. VERTICAL ADJUSTMENT:. LOOSEN TWO () S, ITEM 8.. SLIDE BLADE GUARD UP OR DOWN AS NEEDED.. RETIGHTEN S. 7090:BLADE GUIDE ASSEMBLY, FRONT ITEM 7080 8800 900 9900 GUIDE HOLDER CARBID INSERT Figure 0 BLADE GUIDE ASSEMBLY, FRONT (BM-V-SDB & BM-V-SD) KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-7 OF

REV F: 0/ BLADE GUIDE ASSEMBLY, DRIVE SIDE 70900 (BM-V-SB, S, SD): BLADE GUIDE ASSEMBLY, REAR 7090 (BM-V-SB, S, SD): BLADE GUIDE ASSEMBLY, REAR ITEM 7 8 9 0 7080 708 7090 70970 70970 8900 8800 88900 900 90 9900 900 900 98700 GUIDE HOLDER / FOR 70900 (BM-V-SB, S, SD) GUIDE HOLDER / FOR 7090 (BM-V-SDB) GUIDE REAR GUARD FRONT GUARD CARBID INSERT BALL PLUNGER NUT PIN REFER TO BLADE GUIDE ASSEMBLY, TAKE-UP SIDE (FIGURE 9) FOR ADJUSTMENT INSTRUCTIONS. Figure BLADE GUIDE ASSEMBLY, DRIVE SIDE (BM-V-S, SB, SD, SDB) KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-8 OF

REV F: 0/ HANDLES 700: TOP HANDLE ASSEMBLY - AIR ITE M 7 8 9 0 7 8 709700 70970 00770 90 000 0000 00 000 700 70070 70070 780080 7800 80080 80080 889000 90 990 HANDLE, LEFT HALVE HANDLE, RIGHT HALVE VALVE PLUG GUARD VALVE STEM LEVER SLEEVE AIR HANDLE ELBOW RED AIR TUBE GREEN AIR TUBE O-RING O-RING NUT PIN SPRING Figure TOP HANDLE ASSEMBLY - AIR KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-9 OF

REV F: 0/ 70880: REAR HANDLE ASSEMBLY, AIR ITEM 700 7090 7000 8090 880 889000 HANDLE TRIGGER REAR HANDLE, TRIGGER REAR HANDLA FRAME ROLL PIN SPRING Figure REAR HANDLE ASSEMBLY KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-0 OF

REV F: 0/ SPRAY OPTIONS 709890: SPRAY TUBE UNDER BEAM ASSEMBLY (BM-V-SDB, SD, S) 70990: SPRAY TUBE UNDER BEAM ASSEMBLY (BM-V-SB) ITEM 709870 709880 709900 7000 7000 70070 70090 700 80 7 8 BRACKET TUBE, FOR BM-V-SDB, SD, S TUBE, FOR BM-V-SB COUPLING ELBOW COUPLING MALE PLUG SOCKET ELBOW Figure SPRAY TUBE UNDER BEAM ASSEMBLY 70897: EXTERNAL SPRAY NOZLE ITEM 7 8 709870 70000 70000 7000 700 70070 70090 80 BRACKET ELBOW ELBOW PIPE BUSHING SPRAY NOZLE MALE PLUG SOCKET Figure 70897; EXTERNAL SPRAY NOZZLE KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ MOTOR ASSEMBLY 70 700 700 Rotor Shaft Ass y 7000 7000 7000 Motor Shaft 070 00 00 Rotor BM-V: HP MOTOR ITEM 7 8 9 0 OPTIONS 0800 700 OPTIONS 700 00 00 000 000 00980 080 7800 79070 900 900 90700 STATOR, CHART BELOW COVER, MOTOR HOUSING KEY ROTOR-SHAFT ASSEMBLY MOTOR HOUSING BEARING BEARING RETAINING RING RETAINING RING RETAINING RING RETAINING RING O-RING EXPANSION PLUG SET WASHER MOTOR ASS'Y 0V, HP, PH, 0HZ,.AMPS 7070-0-0 MOTOR ASS'Y V, HP, PH, 0HZ,.AMPS 7070--0 MOTOR ASS'Y 0V, HP, PH, 0HZ,.7AMPS 700-0-0 MOTOR ASS'Y V, HP, PH, 0HZ,.AMPS 700--0 MOTOR ASS'Y V, HP, PH, 0HZ,.0 AMPS 7000 MOTOR ASS'Y 80V, HP, PH, 0HZ,.7 AMPS 700-80-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700-0-0 MOTOR ASS'Y V, HP, PH, 0HZ,. AMPS 700--0 MOTOR ASS'Y 08V, HP, PH, 0HZ,. AMPS 700-08-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700-0-0 MOTOR ASS'Y V, HP, PH, 0HZ,. AMPS 700--0 MOTOR ASS'Y 0V, HP, PH, 0HZ,.AMPS 700 MOTOR ASS'Y 80V, HP, PH, 0HZ,.9 AMPS 700-80-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,.8 AMPS 700-0-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700-0-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700-0-0 MOTOR OPTION MOTOR ASS'Y BM-V: HP MOTOR ASSEMBLY OPTIONS with STATOR 070 070 00 00 000 00 00 00 00 00 00 00 00 00 00 00 STATOR 70 70 700 700 700 700 700 700 700 700 700 700 700 700 700 700 ROTOR Figure HP MOTOR OPTIONS KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

700 Rotor Shaft Ass y REV F: 0/ 700 Motor Shaft 00 Rotor BM-V: HP MOTOR ITEM 7 8 9 0 OPTIONS 0800 700 700 700 00 00 000 000 00980 080 7800 79070 900 900 90700 STATOR, CHART BELLOW COVER, MOTOR HOUSING KEY ROTOR-SHAFT ASSEMBLY MOTOR HOUSING BEARING BEARING RETAINING RING RETAINING RING RETAINING RING RETAINING RING O-RING EXPANSION PLUG SET WASHER MOTOR ASS'Y V, HP, PH, 0HZ, 7.0 AMPS 7000 MOTOR ASS'Y 80V, HP, PH, 0HZ,. AMPS 700-80-0 MOTOR ASS'Y 0V, HP, PH, 0HZ, 8.8 AMPS 700-0-0 MOTOR ASS'Y V, HP, PH, 0HZ,. AMPS 700--0 MOTOR ASS'Y 08V, HP, PH, 0HZ, 8. AMPS 700-08-0 MOTOR ASS'Y 0V, HP, PH, 0HZ, 8.8 AMPS 700-0-0 MOTOR ASS'Y V, HP, PH, 0HZ, 7. AMPS 700--0 MOTOR ASS'Y 0V, HP, PH, 0HZ,.8AMPS 700 MOTOR ASS'Y 80V, HP, PH, 0HZ,.0 AMPS 700-80-0 MOTOR ASS'Y 0V, HP, PH, 0HZ, 8. AMPS 700-0-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700-0-0 MOTOR ASS'Y 0V, HP, PH, 0HZ, 8. AMPS 700-0-0 MOTOR OPTION MOTOR ASS'Y BM-V: HP MOTOR ASSEMBLY OPTIONS with STATOR 000 00 00 00 00 00 00 00 00 00 00 00 STATOR 700 700 700 700 700 700 700 700 700 700 700 700 ROTOR Figure 7 HP MOTOR OPTIONS KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

7080 Rotor Shaft Ass y 7070 Motor Shaft REV F: 0/ 000 Rotor BM-V: HP MOTOR ITEM 7 8 9 0 OPTIONS 0800 700 7080 7090 00 00 000 000 00980 080 7800 79070 900 900 90700 STATOR, CHART BELOW COVER, MOTOR HOUSING KEY ROTOR-SHAFT ASSEMBLY MOTOR HOUSING BEARING BEARING RETAINING RING RETAINING RING RETAINING RING RETAINING RING O-RING EXPANSION PLUG SET WASHER MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700 MOTOR ASS'Y 80V, HP, PH, 0HZ, 7.8AMPS 700-80-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,.7AMPS 700-0-0 MOTOR ASS'Y 80V, HP, PH, 0HZ, 7.7 AMPS 700-80-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700-0-0 MOTOR ASS'Y V, HP, PH, 0HZ, 7.0 AMPS 7000 MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700-0-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,.0 AMPS 700-0-0 MOTOR ASS'Y 0V, HP, PH, 0HZ,. AMPS 700-0-0 MOTOR ASS'Y V, HP, PH, 0HZ, 7. AMPS 700--0 MOTOR OPTION MOTOR ASS'Y BM-V: HP MOTOR ASSEMBLY OPTIONS with STATOR 000 000 000 000 000 0000 000 000 000 000 STATOR 7080 7080 7080 7080 7080 7080 7080 7080 7080 7080 ROTOR Figure 8 HP MOTOR OPTIONS KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ POWER SUPPLY OPTIONS 7000 POWER CORD ASS'Y, V, ATD AIR ITEM 7 8 9 0 00 70870 709 00070 000 0080 008 0080 7800 9090 POWER CORD ASSEMBLY, / GASKET COVER, WIRE BOX POWER CORD / POWER CORD / CONNECTOR CORD STRAIN RELIEF CONNECTOR TIMER AIR Figure 9 POWER SUPPLY, V, with ANTI-TIEDOWN, AIR KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ 7000: POWER CORD ASS'Y, V ITEM 7 8 9 00 70870 709 00070 000 0080 008 0080 9090 POWER CORD ASSEMBLY, / GASKET COVER, WIRE BOX POWER CORD POWER CORD CONNECTOR CORD STRAIN RELIEF CONNECTOR Figure 0 POWER SUPPLY, V, without ANTI-TIEDOWN KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ 7000: POWER SUPPLY, NON V, ATD, AIR ITEM 7 8 00000 70870 7090 000 00880 0080 7800 9090 POWER CORD w/male PLUG GASKET COVER, WIRE BOX SOCKET, FEMALE CABLE CONNECTOR CORD GRIP AIR LOGIC MODULE Figure POWER SUPPLY, NON V, with ANTI-TIEDOWN, AIR 7000: POWER SUPPLY, NON V, NO ATD ITEM 7 00000 70870 7090 000 00880 0080 9090 POWER CORD w/male PLUG GASKET COVER, WIRE BOX SOCKET, FEMALE CABLE CONNECTOR CORD GRIP POWER CORD 00000: POWER CORD 0FT LONG (000) + MALE PLUG (000) Figure POWER SUPPLY, NON V, without ANTI-TIEDOWN KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-7 OF

REV F: 0/ 70007: POWER SUPPLY, SINGLE PHASE / 0V ITEM 7 8 9 0 70870 7090 00080 000 000 00880 0080 0900 090 090 9090 GASKET COVER, WIRE BOX POWER CORD PLUG, MALE SOCKET, FEMALE CABLE CONNECTOR CORD GRIP CAPACITOR START MOTOR START CAPACITOR 0-8 MFD RUN CAPACITOR 0MFD Figure POWER SUPPLY, SINGLE PHASE, V KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-8 OF

REV F: 0/ WIRING DIAGRAMS SINGLE PHASE 0V CONTROL VOLTAGE MOTOR OPTION -POLE CONTACTOR OVERLOAD RELAY 0V MOTOR 0V, 0HZ,.7AMPS, HP 000 0970 0V MOTOR 0V, 0HZ,.AMPS, HP 000 0970 NOTES:. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.. THE CAPACITOR AND THE SWITCH CAP. START MOTOR AR MOUNTED INSIDE THE MAGNETIC PANEL BOX.. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION.. THE GROUND WIRE (GREEN) OF THE POWER CABLE IS CONNECTED TO THE FRAME OF THE MACHINE.. TO REVERSE DIRECTION, REVERSE MOTOR WIRES # AND #8. Figure WIRING SINGLE PHASE 0V Air Operated without Anti-Tie Down KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-9 OF

CONTROL VOLTAGE V V SINGLE PHASE V MOTOR OPTION -POLE CONTACTOR MOTOR V, 0HZ,.AMPS, HP 0008 MOTOR V, 0HZ,.AMPS, HP 0008 REV F: 0/ OVERLOAD RELAY 0900 0900 NOTES:. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.. THE CAPACITOR AND THE SWITCH CAP. START MOTOR AR MOUNTED INSIDE THE MAGNETIC PANEL BOX.. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION.. THE GROUND WIRE (GREEN) OF THE POWER CABLE IS CONNECTED TO THE FRAME OF THE MACHINE.. TO REVERSE DIRECTION, REVERSE MOTOR WIRES # AND #8. Figure WIRING SINGLE PHASE V Air Operated without Anti-Tie Down KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-0 OF

... REV F: 0/ DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION. To obtain the correct Kentmaster part number for -pole contactor and overload relay, please contact the Kentmaster representative. Figure WIRING PH DIFFERENT CONTROL AND MOTOR VOLTAGE - Air Operated without Anti-Tie Down KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

... REV F: 0/ DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION. To obtain the correct Kentmaster part number for -pole contactor and overload relay, please contact the Kentmaster representative. Figure 7 WIRING PH SAME CONTROL AND MOTOR VOLTAGE - Air Operated without Anti-Tie Down KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

... REV F: 0/ DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION. To obtain the correct Kentmaster part number for -pole contactor and overload relay, please contact the Kentmaster representative. Figure 8 WIRING PH DIFFERENT CONTROL AND MOTOR VOLTAGE - Air Operated with Anti-Tie Down KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

... REV F: 0/ DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE OFF POSITION. To obtain the correct Kentmaster part number for -pole contactor and overload relay, please contact the Kentmaster representative. Figure 9 WIRING PH SAME CONTROL AND MOTOR VOLTAGE - Air Operated with AntiTie Down KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ V MOTOR VOLTAGE WITH ATD Figure 0 WIRING PH V MOTOR VOLTAGE - Air Operated with Anti-Tie Down KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ Figure ELECTRIC MOTOR LEAD HOOKUP DIAGRAM PHASE MOTOR KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0- OF

REV F: 0/ [ENGLISH] GENERAL INFORMATION MODELS BM-V-SB with Air CARCASS SPLITTING SAW (7080) BM-V-S with Air CARCASS SPLITTING SAW (70800) BM-V-SD with Air CARCASS SPLITTING SAW (70800) BM-V-SDB with Air CARCASS SPLITTING SAW (7000) SERVICE CENTERS KENTMASTER LTD. (U.K) KENTMASTER MFG. CO., INC. AVONBANK INDUSTRIAL CENTRE WEST TOWN ROAD AVONMOUTH - BRISTOL BS 9DE UNITED KINGDOM 80 SOUTH MOUNTAIN AVE. MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: ++ - (0) 7-90 TELEPHONE: () 9-8888 FAX: ++ - (0) 7-98900 FAX: () 0- KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: () 9-8888 FAX: () 0-7 OF

REV F: 0/ NOTICE TO EMPLOYER AND PURCHASER OF TOOL NOTICE TO SAFETY DIRECTOR You have purchased a powerful tool that, if misused, can cause severe injury and harm to your employees. You must instruct your employees in the safe and proper use of this tool and to follow the safety procedures and instructions that have been supplied by the manufacturer of this tool. Please follow the following instructions.. Instruct tool operators to test the tool each day before using it to be sure it does not malfunction. Remove and repair any tool that malfunctions.. Instruct tool operators to immediately stop using a tool that malfunctions or is defective.. Instruct personnel to immediately remove all tools that malfunction. Be sure to disconnect tool from power supply.. Instruct all personnel to stay clear of tool, and not to stand or walk in front of, or next to tool when in use.. Point out to all personnel the dangers related to the misuse of tool and the importance of following safety procedures and instructions.. Do not make, or allow others to make, alterations or modifications to this tool. Replace all lost or illegible labels. 7. Follow all safety, installation and maintenance instructions provided with this tool. Establish proper safety procedures in accordance with local and national requirements to prevent accidental energizing of tool that can cause injuries. 8. If this tool is sold or change in ownership takes place, you must provide the new owner all safety instructions, notices and maintenance instructions you were originally provided. You can obtain additional copies of the instructions from Kentmaster, free of charge upon request. 9. Give copies of instructions to: (A) Tool Operators (B) Maintenance Supervisor (C) Clean-up Supervisor KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: (88) 9-8888 FAX: (88) 0- Page 8 of

REV F: 0/ GENERAL INFORMATION COVERING: SAFETY PRECAUTIONS AND PLACING INTO SERVICE ELECTRICAL POWERED CARCASS SPLITTING SAW READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THIS INFORMATION INTO THE HANDS OF THE OPERATOR. PLACING INTO SERVICE! WARNING = Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage.! CAUTION = Hazards or unsafe practices which could result in minor personal injury, product or property damage.! NOTICE = Important installation, operation or maintenance information.! WARNING! WARNING Installation, adjustment repair and maintenance of this tool must be made by trained and qualified personnel. Always disconnect power supply from tool before: (A) Installing or removing blade from tool. (B) Making repairs or adjustments to the tool. (C) performing maintenance or cleanup work. INSTALLATION INSTRUCTIONS! WARNING ALL ELECTRICAL WIRING MUST BE DONE BY A LICENSED ELECTRICIAN IN ACCORDANCE WITH THE NATIONAL, STATE AND LOCAL ELECTRICAL CODES. (REFER TO NAMEPLATE ON TOOL FOR PROPER POWER CONFIGURATION).. A BALANCER IS REQUIRED FOR OPERATION AND USE OF THIS TOOL. WEIGHT OF TOOL MUST FALL WITHIN WEIGHT RANGE OF BALANCER. "AIR-BALANCERS" WHICH OPERATE ON COMPRESSED AIR, ARE HIGHLY RECOMMENDED FOR USE WITH BANDMASTER SAWS. THEY PROVIDE LONG TRAVEL AND VERY SMOOTH, UNIFORM RISE AND FALL. THEY CAN BE INTERFACED WITH THE OPERATION OF THE SAW.. INSTALL BALANCER ABOVE WORK AREA. BALANCER MUST HAVE SUFFICIENT VERTICAL TRAVEL SO OPERATOR CAN REACH ENTIRE WORK AREA WITH TOOL WITHOUT STRAIN.. ADJUST BALANCER ACCORDING TO THE OPERATOR'S PREFERENCE AND COMFORT.. TOOL REQUIRES GREASING AFTER EVERY 0 HOURS OF OPERATION. GREASE USING KENTMASTER GREASE (PART NO. 790070).! WARNING WE STRONGLY SUGGEST THAT AN ADDITIONAL SAFETY CHAIN BE USED TO CHAIN BALANCER TO OVERHEAD TROLLEY. THIS ADDITIONAL MEASURE OF SAFETY WILL HELP REDUCE INJURIES. KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: (88) 9-8888 FAX: (88) 0- Page 9 of

REV F: 0/ OPERATING INSTRUCTIONS! WARNING ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL.. HOLD TOOL FIRMLY AT BOTH TRIGGER HANDLES. SQUEEZE TRIGGERS SIMULTANEOUSLY TO ACTIVATE TOOL.. START CUT WITH SAW NOSE POINTED UP AT AN ANGLE.. LEVEL SAW TO HORIZONTAL POSITION IN LOIN AREA.. POINT NOSE OF SAW AT DOWNWARD ANGLE IN CHUCK AND NECK AREA.. A BEGINNING SPLITTER CAN MARK BACKFAT OF BEEF WITH A KNIFE TO HELP GUIDE SAW DOWN CENTER OF BACKBONE AND UNTIL OPERATOR IS FAMILIAR WITH SPLITTING PROCEDURE.. DO NOT EXERT EXCESSIVE PRESSURE. ALLOW TIME FOR THE TOOL TO CUT. 7. PUSH SAW FORWARD SO THAT GUARDS, ITEMS AND, FIGURE, RIDE AGAINST BEEF. THIS HELPS STEADY SAW IN CUT AND HELPS ELIMINATE BLADE JUMPING AND CHATTERING. MAINTENANCE! WARNING ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE AND SERVICE TO THIS TOOL.. FOLLOW PROCEDURE NO. OF INSTALLATION INSTRUCTIONS. BLADE REMOVAL AND CLEANING.! WARNING! WARNING ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR REMOVING BLADE FROM TOOL. ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADES FROM TOOL.. REMOVE PAPER WRAPPER FROM BLADE.. OPEN COVERS, FIGURE, ITEMS AND.. INSTALL TORQUE WRENCH INTO, FIGURE, ITEM, AND TURN COUNTER-CLOCKWISE (CCW). THIS ALLOWS TAKE-UP WHEEL AND SLIDE, ITEM 7 AND 8, TO RETRACT.. SLIDE TAKE-UP WHEEL TO RIGHT.. HOLD BLADE, WITH TEETH FACING AWAY FROM YOU, AND INSTALL INTO SLOT OF BEAM, CONTINUING AROUND AND OVER THE TAKE-UP AND DRIVE WHEELS.. TURN TORQUE WRENCH CLOCKWISE (CW) TO ELIMINATE BLADE SLACK AND TIGHTEN TAKE-UP WHEEL AGAINST BLADE (TORQUE WRENCH IS PRESET AT FACTORY AND WILL SLIP AFTER PLACING PROPER TENSION ON BLADE). 7. TWIST BLADE 90 DEGREES AT BLADE GUARDS AND INSERT BLADE INTO SLOTS WITH TEETH FACING DOWNWARD. 8. TURN DRIVE WHEEL, ITEM 9, SLOWLY BY HAND, ONE OR TWO TURNS TO CHECK TRACKING OF BLADE ON WHEELS. 9. RETORQUE AGAIN UNTIL TORQUE WRENCH SLIPS. SERVICE. KEEP GOOD RECORDS OF ALL SERVICE ACTIVITY AND INCLUDE TOOL IN YOUR PREVENTIVE MAINTENANCE PROGRAM.. USE ONLY GENUINE KENTMASTER REPLACEMENT PARTS TO ASSURE PROPER PERFORMANCE OF TOOL.. CONTACT THE KENTMASTER SUPPLIER NEAREST YOU FOR PARTS AND CUSTOMER SERVICE INFORMATION. KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: (88) 9-8888 FAX: (88) 0- Page 0 of

REV F: 0/ Kentmaster Worldwide Location Kentmaster Equipment (Aust) PTY.LTD. Unit, Central Court Browns Plains Qld. 8 Australia Telephone: (07) 80-800 Fax: (07) 80-79 Australia@Kentmaster.com Kentmaster do Brasil, Ltda. Av. Dr. Joao Teodoro No. 80 Bairro De Vila Rezende 0-0 Piracicaba, SP, Brazil Telephone #: (09) Telephone #: (09)98-97 Fax: (09) Brazil@Kentmaster.com Kentmaster (IRL) LTD. Benamore, Dublin Road. Roscrea, CO, Tipperary, Ireland Telephone: () 00-9 Fax: () 00-99 Ireland@Kentmaster.com Kentmaster Equipment (NZ) LTD. Cooper Street Havelock North New Zealand Telephone #: () 8777 87 Telephone #: 0800 KENTMASTER Fax: () 8777 88 NewZealand@Kentmaster.com Kentmaster South Africa (PTY) LTD. Johannesburg - S. Africa Unit Sunnyrock Park Sunrock Close, Germiston South Africa Telephone: (7) --78 Fax: (7) --79 SouthAfrica@Kentmaster.com Kentmaster (UK ) LTD. Unit Avonbank Ind. Centre West Town Rd, Avonmouth-Bristol, BS 9DE England Telephone: () 7-9-0 Fax: ()-7-9-900 UK@Kentmaster.com Kentmaster Mfg. Co., Inc. 80 South Mountain Ave. Monrovia, CA, 90 USA Telephone #: () 9-8888 Telephone #: (800) -77 Fax: () 0- info@kentmaster.com Kentmaster Omaha 7 South 9th Street Omaha, NE, 87 USA Telephone #: (0) 89- Telephone #: (800) 7-8 Fax: (0) 89- Omaha@Kentmaster.com KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: (88) 9-8888 FAX: (88) 0- Page of

REV F: 0/ INDEX OPERATING AND SAFETY INSTRUCTIONS... OPERATING INSTRUCTIONS... MAINTENANCE... CLEANING AND STERILIZING SAW... WATER CONNECTION... TORQUE WRENCH CALIBRATION... HANGER... TROUBLE SHOOTING HINTS:... SERVICE...7 PARTS BOOK...7 MODELS MAIN ASSEMBLIES...7 DRIVE WHEEL ASSEMBLY...0 TAKE-UP SIDE ASSEMBLY... DRIVE SIDE ASSEMBLY - AIR... BLADE GUIDE ASSEMBLY, TAKE-UP SIDE... BLADE GUIDE ASSEMBLY, DRIVE SIDE...8 HANDLES...9 SPRAY OPTIONS... MOTOR ASSEMBLY... BM-V: HP MOTOR... POWER SUPPLY OPTIONS... WIRING DIAGRAMS...9 V MOTOR VOLTAGE WITH ATD... NOTICE TO EMPLOYER AND PURCHASER OF TOOL...8 GENERAL INFORMATION...9 INSTALLATION INSTRUCTIONS...9 OPERATING INSTRUCTIONS...0 MAINTENANCE...0 SERVICE...0 Kentmaster Worldwide Location... INDEX... FIGURES - INDEX... KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: (88) 9-8888 FAX: (88) 0- Page of

REV F: 0/ FIGURES - INDEX Figure BM-V-... Figure MODELS BM-V- WITH AIR...8 Figure BOM FOR MODELS BM-V- WITH AIR...0 Figure TAKE-UP SIDE ASSEMBLY... Figure TAKE-UP SIDE ASSEMBLY BOM... Figure DRIVE SIDE ASSEMBLY - AIR... Figure 7 BOM FOR DRIVE SIDE ASSEMBLY WITH AIR... Figure 8 TRANSMISSION OVERVIEW... Figure 9 BLADE GUIDE ASSEMBLY, FRONT (BM-V-S & SB)... Figure 0 BLADE GUIDE ASSEMBLY, FRONT (BM-V-SDB & BM-V-SD)...7 Figure BLADE GUIDE ASSEMBLY, DRIVE SIDE (BM-V-S, SB, SD, SDB)...8 Figure TOP HANDLE ASSEMBLY - AIR...9 Figure REAR HANDLE ASSEMBLY...0 Figure SPRAY TUBE UNDER BEAM ASSEMBLY... Figure 70897; EXTERNAL SPRAY NOZZLE... Figure HP MOTOR OPTIONS... Figure 7 HP MOTOR OPTIONS... Figure 8 HP MOTOR OPTIONS... Figure 9 POWER SUPPLY, V, with ANTI-TIEDOWN, AIR... Figure 0 POWER SUPPLY, V, without ANTI-TIEDOWN... Figure POWER SUPPLY, NON V, with ANTI-TIEDOWN, AIR...7 Figure POWER SUPPLY, NON V, without ANTI-TIEDOWN...7 Figure POWER SUPPLY, SINGLE PHASE, V...8 Figure WIRING SINGLE PHASE 0V Air Operated without Anti-Tie Down...9 Figure WIRING SINGLE PHASE V Air Operated without Anti-Tie Down...0 Figure WIRING PH DIFFERENT CONTROL AND MOTOR VOLTAGE - Air Operated without Anti-Tie Down Figure 7 WIRING PH SAME CONTROL AND MOTOR VOLTAGE - Air Operated without Anti-Tie Down... Figure 8 WIRING PH DIFFERENT CONTROL AND MOTOR VOLTAGE - Air Operated with Anti-Tie Down... Figure 9 WIRING PH SAME CONTROL AND MOTOR VOLTAGE - Air Operated with Anti-Tie Down... Figure 0 WIRING PH V MOTOR VOLTAGE - Air Operated with Anti-Tie Down... Figure ELECTRIC MOTOR LEAD HOOKUP DIAGRAM PHASE MOTOR... KENTMASTER MFG. CO., INC. 80 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 90 UNITED STATES OF AMERICA TELEPHONE: (88) 9-8888 FAX: (88) 0- Page of