ir and Vacuum Sewer Valves ir and Vacuum Sewer Valves Valve Function Exhausts air as a pipeline fills, and allows air in as pipeline drains Features Include Standard and short body series available vailable in sizes thru 10 ll RISPIN ir and Vacuum Valves have standard una-n seating material with a Shore durometer of 0-80. This standard seat allows drip tight closure beyond - PSIG. Occasionally, a gravity system operates at pressures less than 10 PSIG. These applications require a soft seating material which will prevent leakage down to PSIG. This soft seating material should not be applied to systems with operating pressures greater than 0 PSIG, or high pressure leaks may occur around the seat. Stainless Steel Trim Standard ir and Vacuum Sewer Valves permit a large volume of air to be released from a pipeline when it is filling. It also allows air into a system when draining. RISPIN ir and Vacuum Sewer Valves feature a rigid stainless steel valve plug to seal off the outlet orifice. s a result, damage to the seating surface is much less likely to occur in surge conditions. drawing of a typical Sewer ir and Vacuum Valve seating area is shownbelow. The valve plug is protected from a rush of air by a stainless steel baffle. The baffle provides a rigid support for the float guide bushing while allowing the float rod enough clearance for self seating operation. The RISPIN ir and Vacuum Sewer Valve, like the light body Pressure Sewer Valve, is designed for a maximum cold water working pressure of 300 PSIG. ny combination of the Sewer ir and Vacuum Valve and Sewer Pressure ir Release Valve can be made with the appropriate piping arrangements to accommodate a specific application. Short ir & Vacuum Sewer Series MODEL INLET OUTLET HEIGHT S10S screwed 1 screwed 1 1/ S10S screwed 1 screwed 16 3/ S0S screwed screwed 1 1/ S0S screwed screwed 16 3/ Where height restrictions do not permit the use of the standard height valve, a short body Sewer ir and Vacuum or Pressure ir Release Valve can be supplied. Their function is identical to the standard Sewer Valves except that they operate in a shorter body. S SERIES rispin Valve, 600 Fowler ve., erwick, P 603 1-800-IR-VLV T: (0) - F: (0) -6 WWW.RISPINVLVE.OM sales@crispinvalve.com S
ir and Vacuum Sewer Valves ir and Vacuum Sewer Valves S SERIES D 0 1 ackflush Optional 8 0 11 1 1 3 1 3 PRT ITEM MTERIL NO. 1 TOP ast Iron FLNGE ast Iron 3 ODY, SREW ast Iron 3F ODY, FLNGE ast Iron FLNGE GSKET rmstrong SET una-n Rubber 6 VLVE & FLOT ROD Stainless Steel ROD GUIDE STND Stainless Steel 8 FLOT ROD GUIDE Nylatron FLOT Stainless Steel 11 ROD GUIDE NUT Stainless Steel 1 STND ROD SREW Stainless Steel STND ROD SREW Stainless Steel 1 STND ROD GSKET Fibre 1 STND ROD NUT Steel 1 FLNGE OLT Steel FLNGE NUT Steel 33 FLUSH PLUG Steel Standard apacity/light ody Series Model Inlet Outlet Width Width Height Height NPT NPT w/ack w/ack w/ack Flush Flush Flush SL0 1-11/16 1-3/ 1-1/ -1/ 60 Note: Operating pressures below 0 PSIG require soft seating material. Dimensions and Weights Model Inlet Outlet Height Width NPT Height Width w/ack w/ack w/ack Flush Flush Flush S0 NPT 1/ 10 1/16 1/ -1/ 3 10 S1 1# Flg. 10 1/16 36 1/ -1/ 6 S30 3 NPT 3 1 3/ 10 1/ -1/ 100 11 S31 3 1# Flg. 3 1 3/ 10 /16-1/ 110 163 S NPT 3 1/ 11 1/ 16 10 1 S1 1# Flg. 3 1/ 11 1/ 3 1/ 16 13 S61 6 1# Flg. 6 6 3/8 1 1/ 3 16-1/ 10 30 S81 8 1# Flg. 8 /16 1 3/ 3-1/ 33 0 S101 10 1# Flg. 10 36 1/ 1 1/ 3-1/ 00 80 *ll rispin valves are hydrostatically tested at 10% of their maximum working pressure. ack flushing attachments are available with any sewer valve arrangement and include: isolation gate valve, - 1 flushing valves and of 1 hose with quick disconnect attachments. 10 S rispin Valve, 600 Fowler ve., erwick, P 603 1-800-IR-VLV T: (0) - F: (0) -6 WWW.RISPINVLVE.OM sales@crispinvalve.com
D 0 1 8 Submittal Sheet for rispin S Series ir/vacuum Sewer Valve (standard) Manufactured in compliance with NSI/WW 1 Date: October, 001 0 11 1 1 ITEM DESRIPTION MTERIL STM TOP ST IRON 16 L. FLNGE ST IRON 16 L. 3 ODY ST IRON 16 L. FLNGE GSKET RMSTRONG N-80 N/ SET UN-N RUER D000 6 VLVE & FLOT ROD STINLESS STEEL 8 ROD GUIDE STND STINLESS STEEL 8 FLOT ROD GUIDE NYLTRON D8 FLOT STINLESS STEEL 11 ROD GUIDE NUT STINLESS STEEL 1 1 STND ROD SREW STINLESS STEEL 13 STND ROD STINLESS STEEL 8 1 STND ROD GSKET FIER D10 1 OLT STEEL 30 NUT STEEL 63 * DRIN PLUG ST IRON 16 L. 0 INTERFERENE PIN STINLESS STEEL 8 OPTIONL K FLUSH OMPONENTS *1 HOSE SSEMLY D.PLT STEEL&RUER N/ * NIPPLE STEEL 3 *3 NIPPLE STEEL 3 * GTE VLVE RSS N/ * GTE VLVE RSS N/ Size MODEL INLET SIZE OUTLET SIZE D WHT. SL0 NPT 1 NPT. 1.0 SL0 NPT 1 NPT 11.. 60 3 1 3 ir and Vacuum Release Valve(s) shall be installed at high points in the main line, or as directed by the engineer. This will permit the release of air as the main is filling, or relieve the vacuum as the main is draining or is under negative pressure. The valve(s)hall be of the long body design, and shall operate by sealing the una-n Rubber seat with a stainless steel valve disc as the float rises when water enters the valve body. The valve(s) shall automatically open when the system drains, or is under negative pressure, so that air may enter the line. Valve construction shall be NPT screwed or NSI lass (1, 0) flanged inlet connection, and shall be cast iron body, top and inlet flange (where required), stainless steel trim and float. The outlet connection shall be cast iron body, top and inlet float (where required), stainless steel trim and float. The outlet shall be NPT screwed. The valve(s) shall be rispin Model ir and Vacuum Sewer Valves, as manufactured by rispin-multiplex Manufacturing o., erwick, P. Option: The valve(s) shall be supplied with back fllushing attachments so that the interior body can be flushed periodically for proper operation. Option: protectop shall be supplied to prevent debris from entering the outlet of thevalve. Option: Where pressures are greater than 300 PSIG, the valve(s) shall be NSI lass flanged inlet connection, and shall have a (steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for rispin ir Valves is 0 to 10 PSIG. Please check one of the following if your operating needs differ: to PSIG 11 to 300 PSIG * Parts are interchangable and optional at customer s request. rispin Valve, 600 Fowler ve., erwick, P 603 1-800-IR-VLV T: (0) - F: (0) -6 WWW.RISPINVLVE.OM sales@crispinvalve.com SUMITTL SHEET FOR S SERIES 11 S
Submittal Sheet for rispin S Series ir/vacuum Sewer Valve (high) Manufactured in compliance with NSI/WW 1 Date: October, 001 SUMITTL SHEET FOR S SERIES 1 S ir & Vacuum Sewer Valve(s) shall be installed at high points in the main line, or as directed by the engineer. This will permit the release of air as the main is filling, or relieve the vacuum as the main is draining or under negative pressure. Valve construction shall be NPT screwed or NSI lass (1, 0) flanged inlet connection, and shall be cast iron body, top and inlet flange (where required), stainless steel trim and float. The outlet connection shall be cast iron body, top and inlet float (where required), stainless steel trim and float. The outlet shall be NPT screwed. The valve(s) shall be rispin Model ir and Vacuum Sewer Valves, as manufactured by rispin-multiplex Manufacturing o., erwick, P. Option: The valve(s) shall be supplied with back fllushing attachments so that the interior body can be flushed periodically for proper operation. Option: protectop shall be supplied to prevent debris from entering the outlet of thevalve. Option: Where pressures are greater than 300 PSIG, the valve(s) shall be NSI lass flanged inlet connection, and shall have a (steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for rispin ir Valves is 0 to 10 PSIG. Please check one of the following if your operating needs differ: to PSIG 11 to 300 PSIG Size MODEL INLET SIZE OUTLET SIZE D WT. S0 NPT NPT 10..0 0 **S1 1# FLG NPT 10..00 6 S0 NPT NPT.0. 10 **S1 1# FLG NPT.0 36. 1 S30 3 NPT 3 NPT 10.00 1. 100 S31 3 1# FLG 3 NPT 10.00 1. 110 S30 3 NPT 3 NPT.0. 11 S31 3 1# FLG 3 NPT.0. 160 S NPT NPT 11.0 3. 10 S1 1# FLG NPT 11.0 3. S NPT NPT 16.00.00 1 S1 1# FLG NPT 16.00 3. 1 * Parts are interchangable and optional at customer s request. **Includes NSI L.1 companion FLG and nipple D 3F 1 1 8 1 8 11 6 1 1 ITEM DESRIPTION MTERIL STM TOP ST IRON 16 L. FLNGE ST IRON 16 L. 3 ODY ST IRON 16 L. FLNGE GSKET RMSTRONG N-80 N/ SET UN-N RUER D000 6 VLVE & FLOT ROD STINLESS STEEL 6/31 ROD GUIDE STND STINLESS STEEL 8 FLOT ROD GUIDE NYLTRON N/ FLOT STINLESS STEEL 11 ROD GUIDE NUT STINLESS STEEL 1 1 STND ROD SREW STINLESS STEEL 13 STND ROD STINLESS STEEL 31 1 STND ROD GSKET FIER D10 1 STND ROD NUT STEEL 63 1 FLNGE OLT STEEL 30 FLNGE NUT STEEL 63 1 OLT STEEL 30 * PLUG ST IRON 16 L. OPTIONL K FLUSH OMPONENTS *1 HOSE SSEMLY D.PLT STEEL & RUER N/ * 1 X L. NIPPLE STEEL 31 *3 1 X 3 NIPPLE STEEL 31 * 1 GTE VLVE RSS N/ * NUT STEEL 63 *6 OLT STEEL 30 * 3 GTE VLVE ST IRON N/ *8 GSKET RMSTRONG N-80 N/ 6 rispin Valve, 600 Fowler ve., erwick, P 603 1-800-IR-VLV T: (0) - F: (0) -6 WWW.RISPINVLVE.OM sales@crispinvalve.com 3 1
D 1 1 0 Submittal Sheet for rispin S Series 6 10 ir/vacuum Sewer Valve (high) Manufactured in compliance with NSI/WW 1 Date: October, 001 1 1 6 3 8 11 6 ITEM QTY. DESRIPTION MTERIL STM 1 TOP ST IRON 16 L. 1 FLNGE ST IRON 16 L. 3F 1 ODY ST IRON 16 L. 1 FLNGE GSKET RMSTRONG N-80 N/ 1 SET UN-N RUER D000 6 1 VLVE&FLOT ROD STINLESS STEEL 6/31 1 ROD GUIDE SUPPORT ST IRON 16 L. 8 1 FLOT ROD GUIDE NYLTRON N/ 1 FLOT STINLESS STEEL 11 1 ROD GUIDE NUT STINLESS STEEL 1 1 OLT STEEL 30 1 1 FLNGE OLT STEEL 30 1 FLNGE NUT STEEL 63 0 OLT STINLESS STEEL 13 1 FLNGE LIGN. PIN HRDENED STEEL 63 EYE PIN STEEL 63 * PLUG ST IRON 16 L. OPTIONL K FLUSH OMPONENTS *1 1 HOSE SSEMLY D.PLT STEEL&RUER N/ * 1 1 X L. NIPPLE STEEL 31 *3 1 1 X 3 NIPPLE STEEL 31 * 8 STUD STEEL 30 * 16 NUT STEEL 63 *6 1 GTE VLVE ST IRON N/ *8 1 8 GTE VLVE ST IRON N/ * 1 GSKET RMSTRONG N-80 N/ 3F 8 6 ir and Vacuum Sewer Valve(s) shall be installed at high points in the main line, or as directed by the engineer. This will permit the release of air as the main is filling, or relieve the vacuum as the main is draining or is under negative pressure. Valve construction shall be NPT screwed or NSi lass (1, 0) flanged inlet connection, and shall be cast iron body, top and inlet flange (where required), stainless steel trim and float. The outlet connection shall be cast iron body, top and inlet float (where required), stainless steel trim and float. The outlet shall be NPT screwed. The valve(s) shall be rispin Model ir and Vacuum Sewer Valves, as manufactured by Multiplex Manufacturing o., erwick, P. Option: The valve(s) shall be supplied with back fllushing attachments so that the interior body can be flushed periodically for proper operation. Option: protectop shall be supplied to prevent debris from entering the outlet of thevalve. Option: Where pressures are greater than 300 PSIG, the valve(s) shall be NSI lass flanged inlet connection, and shall have a (steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for rispin ir Valves is 0 to 10 PSIG. Please check one of the following if your operating needs differ: to PSIG 11 to 300 PSIG * Parts are interchangable and optional at customer s request. Size MODEL INLET SIZE OUTLET SIZE D WT. S61 6 1# FLG 6 NPT 1.0 6.0 10 S61 6 1# FLG 6 NPT 16. 3.00 38 S81 8 1# FLG 8 NPT 1..0 33 S81 8 1# FLG 8 NPT. 3.00 0 S101 10 1# FLG 10 NPT 1. 36. 00 S101 10 1# FLG 10 NPT.00 3.0 80 rispin Valve, 600 Fowler ve., erwick, P 603 1-800-IR-VLV T: (0) - F: (0) -6 WWW.RISPINVLVE.OM sales@crispinvalve.com SUMITTL SHEET FOR S SERIES S
SUMITTL SHEET FOR S SERIES 1 Submittal Sheet for rispin S Series 1 ir/vacuum Sewer Valve (S) Manufactured in compliance with NSI/WW 1 Date: October, 001 ir and Vacuum Release Valve(s) shall be installed at high points in the main line, or as directed by the engineer. This will permit the release of air as the main is filling, or relieve the vacuum as the main is draining or is under negative pressure. Valve construction shall be NPT screwed or NSi lass (1, 0) flanged inlet connection, and shall be cast iron body, top and inlet flange (where required), stainless steel trim and float. The outlet connection shall be cast iron body, top and inlet float (where required), stainless steel trim and float. The outlet shall be NPT screwed. The valve(s) shall be rispin Model ir & Vacuum Sewer Valves, as manufactured by rispin-multiplex Manufacturing o., erwick, P. Option: The valve(s) shall be supplied with back fllushing attachments so that the interior body can be flushed periodically for proper operation. Option: The valve(s) shall be a special short body short valve with overall height not to exceed 1 1/. Option: protectop shall be supplied to prevent debris from entering the outlet of thevalve. Option: Where pressures are greater than 300 PSIG, the valve(s) shall be NSI lass flanged inlet connection, and shall have a (steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for rispin ir Valves is 0 to 10 PSIG. Please check one of the following if your operating needs differ: to PSIG 11 to 300 PSIG * Parts are interchangable and optional at customer s request. ITEM DESRIPTION MTERIL STM 1 TOP ST IRON 16 L. FLNGE ST IRON 16 L. 3 ODY ST IRON 16 L. FLNGE GSKET RMSTRONG N-80 N/ SET UN-N RUER D000 6 VLVE & FLOT ROD STINLESS STEEL 8 ROD GUIDE STND STINLESS STEEL 8 FLOT ROD GUIDE NYLTRON D8 FLOT STINLESS STEEL 11 ROD GUIDE NUT STINLESS STEEL 1 1 STND ROD SREW STINLESS STEEL 13 STND ROD STINLESS STEEL 8 1 STND ROD GSKET FIER D10 1 STND ROD NUT STEEL 63 1 OLT STEEL 30 NUT STEEL 63 * FLUSH PLUG ST IRON 16 L. 0 INTERFERENE PIN STINLESS STEEL 8 OPTIONL K FLUSH OMPONENTS *1 HOSE SSEMLY D.PLT STEEL & RUER N/ * NIPPLE STEEL 3 *3 NIPPLE STEEL 3 * NIPPLE STEEL 3 * GTE VLVE RSS N/ *6 GTE VLVE RSS N/ Size MODEL INLET SIZE OUTLET SIZE D WHT. S10S NPT 1 NPT 10. 1. S10S NPT 1 NPT. 16. 66 S0S NPT NPT 10. 1. S0S NPT NPT. 16. 66 S rispin Valve, 600 Fowler ve., erwick, P 603 1-800-IR-VLV T: (0) - F: (0) -6 WWW.RISPINVLVE.OM sales@crispinvalve.com D 1 1 0 1 3 1 1 6 11 8 3 6 1 6