Technical Specifications Certifications & Ratings* 10 year warranty UL 844, UL 1598/A Class I, Div. 1, Groups B, C, D Class I, Div. 2, Groups A, B, C, D Class II, Div. 1, Groups E, F, G Class II, Div. 2 Groups F, G *ETL listed Tempered Glass Lens Polycarbonate Lens Class III, Div 1 & 2 CSA 22.2 o. 137-M81 L70 rated for >300,000 hours IP66 / 67 / 69 EMA 4X Factory-sealed Mechanical Information: Fixture weight: Class I, Div. 1 CID2, Class II, Class III Wall mount models: 14.5 lb (6.6 kg) - Glass lens 10 lb (4.5 kg) - Polycarbonate lens 12 lb (5.4 kg) - Glass lens 15 lb (6.8 kg) - Polycarbonate lens 45 o wall mount models: 14 lb (6.4 kg) - Polycarbonate lens 17 lb (7.7 kg) - Tempered glass lens 45 o stanchion mount: 15 lb (6.8 kg) - Polycarbonate lens 34mm conveyor mount: Shipping weight: Cabling: Impact rating: 15 lb (6.8 kg) - Polycarbonate lens Add 2 lb (0.91 kg) to weights above 10 (3.5 m) 5 conductor SOOW IK10 - Polycarbonate lens IK07 - Tempered glass lens Vibration resistance: Tested per IEC 60068-2-6 Electrical Specifications: Operating voltage: Total system power consumption: Operating temperature: 100-277 VAC, 120-280 VAC - Battery backup See table -40 F to +149 F (-40 C to +65 C) EMC: FCC Title 47, Subpart B, Section 15, Class A device RF Immunity 20V/m 80MHz-1GHz. Transient protection: Harmonics: THD: < 20% Power factor: > 0.9 Construction: Housing: Finish: Corrosion resistance: Lens: Photometric Information: CRI: 80 CCT: 6kV, 2 Ohm line-line and line-ground IEC 61000-3-2, Class C Copper-free aluminum Superior dual coat finish - Sealed polyester topcoat - Chemical-resistant epoxy primer 3,000-hour salt spray per ASTM B117 Tempered glass 5000K (cool white) 4000K (neutral white) 2700K (warm white) Optics: 360 180 forward throw for 45 mounting Wide for 0 mounting All values typical unless otherwise stated (tolerance +/- 10%) Temperature Ratings Ambient Temperature Range T4A -40 F to +149 F (-40 C to +65 C) Ambient Temperature Range T5-40 F to +113 F (-40 C to +45 C) 76 www.dialight.com
Ordering Information AL 2 D G Product Code Cert. Lens Material Beam Dist. CCT & CRI Oper. Voltage Type Controls Mounting Options HW Access. Elect. Access. Coatings Battery Product Code CCT & CRI Mounting Options 3 Hardware Accessories AL Certification C 1 UL 844 CIass I Div. 1, Class II Div. 1 CSA C22.2 o. 137 D Area Light UL 844 CIass I Div. 2, Class III CSA C22.2 o. 137 F UL 844 CIass II Div. 1, 2, Class I Div. 2 CSA C22.2 o. 137 C Cool White 5000K - 80 CRI eutral White 4000K - 80 CRI W Warm White 2700K - 80 CRI Operating Voltage 2 100-277 VAC, 120-250 VDC A Appleton Mercmaster III B Swivel Bracket, Locking 0-90 316 Stainless Steel C Retro-fit Adapter 6 Universal Mounting Adapter (UMA) Crouse-Hinds - Champ Wire leads for Mounting Options - A, C, G, H, K, M, S, U, V, W, Y W 10 ft (3 meter) Power Cable for Mounting Options - B, Electrical Accessories o Option P 1 UL 844 CIass I Div. 1 Group B (Hydrogen) CSA C22.2 o. 137 Lens Material 5 Polycarbonate - Diffused 7 Glass - Clear W 2 Wide Type 5 3 3,001-4,000 4 4,001-5,000 6 5,001-6,000 7 6,001-7,000 9 8,001-9,000 Controls D Dimming (0-10 VDC) G H K M S U 4 V W Y GE Filtr-Gard Thomas & Betts Hazlux Killark Certilite & Certilite V Appleton Mercmaster II 3/4 PT 45 Stanchion Mount UMA - Mounting Hub 0 Wall Mount 45 Wall Mount 34mm Conveyor Mount Coatings G Gray (RAL 7040) Battery o Option otes 1) When ordering Certification C - UL 844 Class I Div. 1 or P - UL 844 Class I Div. 1 Group B (Hyrdogen): Lens Material = 7 - Glass, Mounting Option = - 3/4 PT or B - Swivel Bracket, Locking 0 o - 90 o 316 Stainless Steel, Hardware Access. = W - 10ft (3 meter) Power Cable. 2) When ordering W - Wide: Type = 7. 3) When ordering Mounting Options UMA or Retro-fit : Hardware Accessories =. (only available for ALD and ALF series) 4) When ordering Mounting Option U - UMA Mounting Hub HZXW01, HZXW45, HZXS45 or HZXCV34 is required. See page 83 for details. 5) For lumen output see page 80-81. 6) All names and brands are property of their respective holders. Additional features and selections are available, please see the UL Area Light Technical Spec Sheet or your Dialight representative for more information. 180 o 360 o Wide www.dialight.com 77
Technical Specifications - 24-48 VDC, 347-480 VAC, Battery Backup Models Mechanical Information: Fixture weight: 14.5 lb (6.6 kg) - Class I, Div. 1 CID2, Class II, Class III 10 lb (4.5 kg) - Polycarbonate lens 12 lb (5.4 kg) - Glass lens Wall mount models: 15 lb (6.8 kg) - Polycarbonate lens 45 o wall mount models: 14 lb (6.4 kg) - Polycarbonate lens 17 lb (7.7 kg) - Tempered glass lens 45 o stanchion mount: 15 lb (6.8 kg) - Polycarbonate lens 34mm conveyor mount: 15 lb (6.8 kg) - Polycarbonate lens Battery backup: 35 lb (15.9 kg) - Polycarbonate lens 37 lb (16.8 kg) - Tempered glass lens Certifications & Ratings* 5 year warranty UL 844, UL 1598/A Class I, Div. 1 Groups A, B, C, D Class I, Div. 2 Groups A, B, C, D Class II, Div. 1 Groups E, F, G Class II, Div. 2 Groups F, G Class III, Div. 1 & 2 *ETL listed Tempered Glass Lens Polycarbonate Lens Battery Backup CSA 22.2 o. 137-M81 CSA 22.2 o. 250 L70 rated for >150,000 hours IP66 / 67 EMA 4X Factory-sealed Shipping weight: Add 2 lb (0.91 kg) to weights above Cabling: 347-480 VAC & 24-48 VDC 10 (3.5 m) 5 conductor SOOW Battery backup Wiring compartment Impact rating: Electrical Specifications: Operating voltage: Total system power consumption: Operating temperature: IK10 - Polycarbonate lens IK07 - Tempered glass lens 347-480 VAC 24-48 VDC 120-277 VAC - Battery backup See table -40 F to +149 F (-40 C to +65 C) EMC: FCC Title 47, Subpart B, Section 15, Class A device RF Immunity 20V/m 80MHz-1GHz. Transient protection: Harmonics: THD: < 20% Power factor: > 0.9 Construction: Housing: Finish: Corrosion resistance 1 : Lens: Photometric Information: CRI: 75 CCT: 6kV, 2 Ohm line-line and line-ground IEC 61000-3-2, Class C Copper-free aluminum Superior dual coat finish - Sealed polyester topcoat - Chemical-resistant epoxy primer 3,000-hour salt spray per ASTM B117 Tempered glass 5000K (cool white) 4000K (neutral white) Optics: 360 180 forward throw for 45 mounting All values typical unless otherwise stated (tolerance +/- 10%) Temperature Ratings Ambient Temperature Range T4A -40 F to +113 F (-40 C to +45 C) Ambient Temperature Range T5-40 F to +149 F (-40 C to +65 C) 78 www.dialight.com
Ordering Information - 24-48 VDC, 347-480 VAC, Battery Backup Models AL G Product Code Cert. Lens Material Beam Dist. CCT & CRI Oper. Voltage Type Controls Mounting Options HW Access. Elect. Access. Coatings Battery Product Code CCT & CRI Mounting Options 2 Hardware Accessories AL Area Light Certification C 1 UL 844 CIass I Div. 1, Class II Div. 1 CSA C22.2 o. 137 B L Cool White 5000K - 70 CRI eutral White 4000K - 70 CRI Operating Voltage Retro-fit Adapter 4 Universal Mounting Adapter (UMA) Wire leads for Mounting Options - A, C, G, H, K, M, S, U, V, W, Y W 10 ft (3 meter) Power Cable for Mounting Options - B, D UL 844 CIass I Div. 2, Class III CSA C22.2 o. 137 F UL 844 CIass II Div. 1, 2, Class I Div. 2 CSA C22.2 o. 137 P 1 UL 844 CIass I Div. 1 Group B (Hydrogen) CSA C22.2 o. 137 Lens Material 5 Polycarbonate - Diffused 7 Glass - Clear 2 4 120-277 VAC - Battery Backup 5 347-480 VAC 6 24-48 VDC Type 3 347-480 VAC 24-48 VDC 120V Battery Backup 4 3.1-4K 2 0.1-2K 5 4.1-5K 5 4.1-5K 6 5.1-6K 7 6.1-7K 7 6.1-7K 7 6.1-7K A Appleton Mercmaster III B Swivel Bracket, Locking 0-90 316 Stainless Steel C G H K M S U V Crouse-Hinds - Champ GE Filtr-Gard Thomas & Betts Hazlux Killark Certilite & Certilite V Appleton Mercmaster II 3/4 PT 45 Stanchion Mount UMA - Mounting Hub 0 Wall Mount Electrical Accessories o Option Coatings G Gray (RAL 7040) Battery Controls W 45 Wall Mount F 3.6V 10Ah imh on Dimming Y 34mm Conveyor Mount o Option otes 1) When ordering Certification C - UL 844 Class I Div. 1 or P - UL 844 Class I Div. 1 Group B (Hyrdogen): Lens Material = 7 - Glass, Mounting Option = - 3/4 PT or B - Swivel Bracket, Locking 0 o - 90 o 316 Stainless Steel, Hardware Access. = W - 10ft (3 meter) Power Cable. 2) When using UMA or Retro-fit mounting options, Hardware Accessories =. 3) ot all lumen options available for all voltage options, consult table. 4) All names and brands are property of their respective holders. Additional features and selections are available, please see the UL Area Light Technical Spec Sheet or your Dialight representative for more information. 4) otes - When Ordering Battery Backup Models Use... Certification = D UL 844 Class I, Division 2 = or Operating Voltage = 2 120-277 VAC Mounting Options = (stainless steel bracket included) Hardware Accessories = (junction box included) Electrical Accessories = (wiring via 3 positions push down terminal block) Battery = F @ 25 C ambient - est. >3 hours Battery backup circuit can be wired in sustained or maintained configurations 180 o 360 o www.dialight.com 79
Tables Letter Output Family 9 9,000 7 7,300 6 5,700 4 4,200 3 3,100 W Wide Lens 100-277 VAC, 120-250 VDC Lens Material Wattage 5000 CCT 4000 CCT 2700 CCT 9000 8800 8200 7 Class I, Div 1 Glass 8600 8400 7900 5 Polycarbonate 8300 8100 7600 66 8800 8600 8000 7 Class I, Div 1 Glass 8400 8200 7700 5 Polycarbonate 8100 7900 7400 7300 7100 6700 7 Class I, Div 1 Glass 7000 6800 6400 5 Polycarbonate 6700 6500 6100 52 7100 6900 6500 7 Class I, Div 1 Glass 6800 6600 6200 5 Polycarbonate 6600 6400 6000 7300 7100 6700 7 Class I, Div 1 Glass 64 7000 6800 6400 5 Polycarbonate 6700 6500 6100 5700 5500 5200 7 Class I, Div 1 Glass 5400 5200 4900 5 Polycarbonate 5300 5100 4800 40 5500 5300 5000 7 Class I, Div 1 Glass 5300 5100 4800 5 Polycarbonate 5100 4900 4600 4200 4100 3800 7 Class I, Div 1 Glass 4000 3900 3600 5 Polycarbonate 3900 3800 3900 30 4100 4000 4100 7 Class I, Div 1 Glass 3900 3800 3900 5 Polycarbonate 3800 3700 3400 3100 3000 2800 7 Class I, Div 1 Glass 2900 2900 2600 5 Polycarbonate 2800 2700 2500 24 3000 2900 2700 7 Class I, Div 1 Glass 2900 2800 2600 5 Polycarbonate 2800 2700 2500 24-48 VDC Letter Output Family 7 7,000 5 5,000 4 3,000 All values typical unless otherwise stated (tolerance +/- 10%) For lighting layouts, please find IES files at www.dialight.com Lens Lens Material Wattage 5000 CCT 4000 CCT 7000 6800 7 Class I, Div 1 Glass 6700 6500 5 Polycarbonate 6700 6500 71 7000 6800 7 Class I, Div 1 Glass 6700 6500 5 Polycarbonate 6700 6500 5000 4900 7 Class I, Div 1 Glass 4800 4700 5 Polycarbonate 4800 4700 49 5000 4900 7 Class I, Div 1 Glass 4800 4700 5 Polycarbonate 4800 4700 3000 2900 7 Class I, Div 1 Glass 2800 2800 5 Polycarbonate 2800 2800 27 3000 2900 7 Class I, Div 1 Glass 2800 2800 5 Polycarbonate 2800 2800 80 www.dialight.com
Tables & Dimensional Drawings 340-480 VAC Letter Output Family 7 7,250 6 6,000 5 5,000 4 4,000 Lens Lens Material Wattage 5000 CCT 4000 CCT 7200 7100 7 Class I, Div 1 Glass 6900 6800 5 Polycarbonate 6900 6800 68 7200 7100 7 Class I, Div 1 Glass 6900 6800 5 Polycarbonate 6900 6800 6000 5800 7 Class I, Div 1 Glass 5700 5600 5 Polycarbonate 5700 5600 58 6000 5800 7 Class I, Div 1 Glass 5700 5600 5 Polycarbonate 5700 5600 5000 4900 7 Class I, Div 1 Glass 4800 4700 5 Polycarbonate 4800 4700 47 5000 4900 7 Class I, Div 1 Glass 4800 4700 5 Polycarbonate 4800 4700 4000 3900 7 Class I, Div 1 Glass 3800 3700 5 Polycarbonate 3800 3700 38 4000 3900 7 Class I, Div 1 Glass 3800 3700 5 Polycarbonate 3800 3700 Letter Output Family 7 7,500 All values typical unless otherwise stated (tolerance +/- 10%) For lighting layouts, please find IES files at www.dialight.com 100-277 VAC Battery Backup Lens Lens Material Wattage 5000 CCT 4000 CCT 7500 7300 5 Polycarbonate 7500 7300 85 7200 7000 5 Polycarbonate 6900 6800 Battery Backup Model www.dialight.com 81
Hazardous Application Area Light Dimensional Drawings Polycarbonate Lens - Option 5 Tempered Glass Lens - Option 7 82 www.dialight.com
Hazardous Application Area Light Accessories Fixtures are available with a factory-installed universal mounting adapter (UMA), see product -chart for details. Choose from one of the four available mounting options: ALxxxx2xDUxG Wall Mount HZXW01 45 Wall Mount HZXW45 45 Stanchion Mount HZXS45 1.25 Slip-fit Pole Mount HZXCV34 Certified to: UL 50E CSA C22.2 o. 94.2-07 HZXSTA100S 1.00 (1.315 Pole OD) slip-fit stanchion mount HZXSTA125S 1.25 (1.660 Pole OD) slip-fit stanchion mount HZXSTA150S 1.50 (1.900 Pole OD) slip-fit stanchion mount HZXSTA200S 2.00 (2.375 Pole OD) slip-fit stanchion mount HZXSTA100T 1.00 (1.315 Pole OD) PT-threaded stanchion mount HZXSTA125T 1.25 (1.660 Pole OD) PT-threaded stanchion mount HZXSTA150T 1.50 (1.900 Pole OD) PT-threaded stanchion mount HZXSTA200T 2.00 (2.375 Pole OD) PT-threaded stanchion mount HZXW3 316 stainless steel bracket HZXW7 Aluminum bracket HZXW4 316 stainless steel bracket with 1.5 pipe clamp HZXW8 Aluminum bracket with 1.5 pipe clamp HZXSAFECBLS Safety cable kit Certified to: UL 50E UL 1203 ISA 12.12.01 CSA C22.2 o. 94.2-07 HBXC1 0.75 PT Ceiling mount Certified to: UL 50E CSA C22.2 o. 94.2-07 Certified to: UL 50E CSA C22.2 o. 94.2-07 HZXJB075 0.75 Ceiling / Wall / Pole mount junction box HZXJB100 1.00 Ceiling / Wall / Pole mount junction box HZXJB125 1.25 Ceiling / Wall / Pole mount junction box HZXJB150 1.50 Ceiling / Wall / Pole mount junction box HZXJB075PC1 0.75 Junction box with photocell HZXJB100PC1 1.00 Junction box with photocell HZXJB125PC1 1.25 Junction box with photocell HZXJB150PC1 1.50 Junction box with photocell Please reference spec sheet at www.dialight.com for all dimensional drawings of mounting options. www.dialight.com 83
Hazardous Application Area Light Retro-fit Options Retro-fit adapters can be factory installed. See product -chart for details. Eaton s Crouse-Hinds Champ GE Lighting Solutions Filtr-Gard Holophane Petrolux II, III Thomas & Betts Hazlux Appleton Mercmaster III Appleton Mercmaster II Killark Certilite & Certilite V *Petrolux adapter available as a standalonne accessory only Eaton s Crouse-Hinds Champ - HZXTHCH Pendant Ceiling Wall Stanchion Quad Mount APM2 CM2 TWM2 JM5 QM25 APM3 CM3 TWM3 PM5 HPM2 GE Lighting Solutions Filtr-Gard - HZXTHGE Pendant Ceiling Wall Stanchion Quad Mount 3P 3F 3C 3W 5S 4P 4F 4W 6S 5J, 6J Holophane Petrolux II, III - HZXTHP3 Pendant Universal Stanchion Ceiling Wall PD U SA CD WL GH ST CE W P A B, C, D Please reference spec sheet at www.dialight.com for all dimensional drawings of retro-fit options. 84 www.dialight.com
Hazardous Application Area Light Retro-fit Options Thomas & Betts Hazlux - HZXTHTB Pendant Pendant Cone Flexible Pendant Ceiling Wall VP2 VA2 VF2 VC2 VB2 VP3 VA3 VF3 VC3 VB3 Wall 25 Angle Stanchion 25 AngleStanchion Straight Stanchion Straight Stanchion VB2-VIB VS4 VS4-VIB VL4 VL4-VIB VB3-VIB VS5 VS5-VIB VL5 VL5-VIB Appleton Mercmaster III - HZXTHAP Pendant Ceiling Wall Stanchion KPA- 75, 100 KPC-75 KPWB-75 KPS-125 KPAF-75, 100 KPC-100 KPWB-100 KPS-150 KPCH-75, 100 KPST-125 KPST-150 Appleton Mercmaster II - HZXTHM2 Pendant Ceiling Wall Stanchion LPA-75 LPC-75 LPWB-75 LPS-125 LPA-100 LPC-100 LPWB-100 LPS-150 Killark Certilite & Certilite V - HZXTHKL Pendant Ceiling Wall Stanchion VMA2B & VMA-2 VMX2B & VMX-2 VMB2B & VMB-2 VMD4B VMA3B & VMA-3 VMX3B & VMX-3 VMB3B & VMB-3 VMD5B VMC2B & VMC-2 VMX6B, 7B, 8B, 9B VMS5B VMC3B & VMC-3 VMF2B, 3B Please reference spec sheet at www.dialight.com for all dimensional drawings of retro-fit options. www.dialight.com 85