Rock N Roll Walker Instruction Manual Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. Record the following information for quick reference. Note: Illustrations are only representative and not actual. Attach copy of sales receipt. Date Purchased: Model Number: - Color Parts List Make sure you have all the parts listed below before using your Walker. If any parts are missing, call Customer Service at 1-800-992-6624. Seat back Nut (X4) Fixed Wheel (X2) Swivel Wheel (X2) Side Mirror (X2) Support Legs (X4) Base Seat Pad Traffic Signal Toy Toy Tray Stabilizer Upper Tray Name of Parts Tools Needed: Screwdriver 1 Seat 2 Side Mirror 3 Toy Tray 4 Upper Tray 5 Support Legs 6 Rocker 7 Stabilizer Pad 8 Wheels 9 Base 10 Height Button Combi USA, Inc. 3520 Westinghouse Blvd., Suite B Charlotte, NC 28273 CombiUSA.com Customer Service 1-800-992-6624
WARNINGS: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH. READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THE WALKER. KEEP INSTRUCTIONS FOR FUTURE USE. ADULT ASSEMBLY REQUIRED. KEEP SMALL PARTS AWAY FROM CHILDREN. In the event of damage or problems, discontinue use and contact Combi Customer Service for instructions: 1-800-992-6624. NEVER LEAVE CHILD UNATTENDED. Always keep child in view while in walker. Always keep child in view while in walker. To avoid burns, keep the child away from hot liquids, ranges, radiators, space heaters, fireplaces, etc. Discontinue use of this product once child can walk unassisted. Do not use the walker if it is damaged or broken. WARNING-sTAIR HAZARD Avoid serious injury or death. Block stairs/steps securely before using walker, even when using parking brake. Use only on flat surfaces free of objects that could cause the walker to tip over. Clean friction pads regularly to maintain stopping performance (figure 1). See Routine Maintenance section for cleaning instructions. This walker is only intended for use with children who can sit upright unassisted; approximately 6 months old. For indoor use only. Maximum weight capacity is 25 lb figure 1 All products specifications are subject to change without notice. Sizes and weights are intended as guides and are approximations. Combi reserves the right to modify the products in its line during the course of the year. Non contractual media. Colors are as accurate as the media in which they appear allows. Combi USA, Inc. 2011-2 -
Assembly Instructions 1. Place Upper Tray on a flat surface. Attach seat back by inserting front tabs on seat back into slots on upper tray (figure 1). figure 1 2. Lower seat back to insert rear tabs into rear slots on upper tray (figure 2). Push seat back down firmly to fully attach seat back. figure 2 3. Loosely place seat cover over the seat back. (figure 3) figure 3 4. Attach seat cover front by inserting the two front tabs into the slots at the front of the seat area. Pull from the bottom, then flip tab over slot to secure. (figure 4) - 3 - figure 4
Assembly Instructions (continued) 5. Attach seat cover sides by inserting each of the six (6) attachment tabs into the slots on the side of the seat area (figure 5). Push tab into slot, then pull from the bottom and flip tab to secure. figure 5 6. Place upper tray assembly upside down on a flat surface. 7. Insert round end of each leg (4) into round hole on underside of the upper tray (figure 6). figure 6 8. Insert nut onto screw attachment by hand to attach each leg. 9. Ensure that each leg is aligned with the side of the upper tray, then use a coin to tighten each attachment nut (figure 7). 10. Turn assembled parts upright. 11. Place base on a flat surface with smooth side up. figure 7 12. Align the rear of the upper tray assembly with the rear of the base. IMPORTANT: The rear of the upper tray must be aligned with the rear of the base before attaching the two pieces in the steps below. The rear of the upper tray is where the seat is located; the rear of the base has a large round hole. (figure 8) back 13. Loosely attach the upper tray assembly to the base by inserting the square ends of the legs into the square holes on the sides of the base, just over the tires. (figure 9) figure 8 front figure 9-4 -
Assembly Instructions (continued) 14. To securely attach each leg to the base, press the button in the center of the tire, while pushing down firmly on the leg (figure 10). The leg will click into position. Repeat for all four (4) legs. 1 2 figure 10 15. Turn the assembled parts over so you can easily access the bottom of the base. 16. Attach the rear wheels into the larger round holes by aligning the notch on the hole with the raised bar on the wheel. Push firmly to securely attach each rear wheel. (figure 11) figure 11 17. Attach the front swivel wheels to the base by pushing each firmly into the small round holes. (figure 12) figure 12 18. Push down firmly on the walker stabilizer to attach it to the base. 19. Turn assembled base and upper tray upright. - 5 -
Assembly Instructions (continued) 20. Turn toy tray over to access bottom side. Unscrew and remove the battery cover (figure 14). Insert two (2) "AA" batteries (figure 15). Replace battery cover and tighten the screw to secure the cover. To turn toy unit on, switch the On/Off switch to "On" (figure 16). figure 14 figure 16 figure 15 21. Attach toy tray to the upper tray (figure 17). NOTE: To remove toy tray, press tabs (x2) located under the upper tray. 22. Attach the traffic signal toy to the toy tray (figure 18). 23. Attach each mirror to the toy tray (figure 19). figure 17 figure 19 figure 18-6 -
3-in-1 Activity Center Stage 1: Stationary Activity Center 1. To engage the stabilizer pad, turn stabilizer knob clockwise until it stops (figure 1). 2. Lift wheel stabilizer on rear wheels upward to secure the wheels. (figure 2). NOTE: To remove from Stationary Activity Center stage, reverse the instructions above. Stage 2: Rocker figure 1 Lower rocker by pressing tab at inside center of base while pulling rocker downward (figure 3). Repeat for other side. Ensure that the rocker is secured in position before using. To remove from Rocker stage, press tabs (x2) under tires on the inside of the walker while pushing upward on rocker (figure 4). Repeat for other side. Ensure that the rocker is completely stored before using in other stages. Stage 3: Walker To use in walker stage, ensure that the rocker is properly stored, rear wheel stabilizer switches are in the down position, and the stabilizer pad is in the up position. figure 2 figure 3 figure 4-7 -
Height Adjustment The legs can be adjusted to three different heights to accommodate the growth of your child. To adjust height: 2 1. Press the button in the center of the tire, while pushing down firmly on the leg (figure 9). The leg will click into position. 1 2. Repeat for all four (4) legs. figure 1 Trouble Shooting Music and sound effects are not working - Check that the battery is in the correct position as indicated inside the unit. - Replace with a new battery, if necessary. Routine Maintenance Store in a cool and dry area, especially in the summer. Do not store the Activity Walker in the trunk of a vehicle. ALWAYS MAKE SURE Friction pads ARE KEPT CLEAN, CLEAN WITH WATER ONLy. Combi USA, Inc. 3520 Westinghouse Blvd., Suite B Charlotte, NC 28273 CombiUSA.com Customer Service 1-800-992-6624 2011-09-13