Page 1 of 9 2/20/2015 Current Date 20Feb2015 HYDRAULICS: Open Center, Load Sensing with Variable Displacement Pumps Hydraulic Pilot Controls Axial Piston Swing Motor Multiple Wet Disk Swing Brake Auxiliary Valve Section Adjustable Flow for Attachments Through Monitor Boom and Arm Reduced Drift Valves Power Boost Auto Power Lift Hydraulic Tank Site Gauge 5,000 Hour Hydraulic Oil Change Interval UNDERCARRIAGE: Two Speed Propel with Auto- Shift Axial Piston Propel Motors Propel Motor Shields Planetary Final Drives Sealed Track Chain Front and Center Track Guides Provisions for Tie Downs X-Frame Car Body Hydraulic Track Adjuster Eight Lower Rollers *One Upper Rollers Spring Applied Hydraulic Released Propel Brake UPPER STRUCTURE: *Right, Left, and Counterweight Mirrors(3) Toolbox Vandal Locks for: Cab Door Service Doors Fuel Cap Tool Box *Counterweight, 5,512 lbs. (2,500 kg) ZAXIS 130-5 EXCAVATOR FRONT ATTACHMENT: Oil Impregnated Bushings Reinforced Resin Thrust Plates Tungsten Carbide Thermal Coating on arm to Bucket Joint Centralized Lubrication System Dirt Seals on Bucket Pins Less Boom Less Arm Less Bucket OPERATOR'S STATION: ZXLink Ultimate Machine Monitoring System w/ 3-year Message Service (Available in United States and Canada only) Adjustable Control Positions (Levers to Seat, Seat to Pedals) 4" Arm Rests Attached to Side Consoles Pilot Control Shut-Off Lever Short Stroke, Low Effort Pilot Levers Switches for Auxiliary Hydraulic Control on RH Pilot Lever Deluxe Adjustable Cloth Seat with Suspension, Reclining Backrest, Headrest, and Adjustable Lumbar Support Multifunction, Color LCD Monitor System with: Diagnostic Capability Systems Monitoring Capability Multiple Language Capability Maintenance Tracking Engine Coolant Temperature Gauge Engine Coolant Temperature Engine Oil Pressure Warning Indicator with Audible Alarm Fuel Gauge with Low Fuel Indicator Work Mode Indicator Auto Idle Indicator Alternator Charge Indicator Air Filter Restriction Indicator Fault Code Alert Indicator Check Engine Indicator Wiper Mode Indicator Work Lights On Indicator Fuel Rate Display Clock Hour Meter Mode Selection: One Work Mode Three Power Modes Numerous Attachment Modes Auto-Climate Control/Air Conditioner, Heater with Pressurizer AM-FM Radio Machine Information Center (MIC) Windshield Wiper/Washer with Intermittent Speed 12V-60W, 5 Amp Cell Phone Power Outlet 2 In. Retractable Seat Belt Tinted Safety Glass Hot/Cold Box Compartment Horn Two Cup Holders Interior Light Coat Hook Floor Mat Motion Alarm with Cancel Switch Transparent Tinted Roof Hatch with Sunshade Four Fluid-Filled Elastic Mounts
Page 2 of 9 2/20/2015 Work Lights: One Mounted on Frame One Mounted on Boom Remote Mounted Engine Oil and Fuel Filters Warning Indicator with Audible Alarm Easy Access Air Conditioning Filter Required - You must select one from each category BASE MACHINE F.O.B Kernersville, North Carolina for Complete Machine. See DEALER-INSTALLED ATTACHMENT section for additional source notes. ZAXIS 130-5 EXCAVATOR 05U0FF $153,946.00 ENGINE *Isuzu AM-4JJ1, Certified to IT4 / Stage IIIB emissions 99 hp Net Peak Power (ISO9249) Turbocharger Electronic Engine Control Unit Auto-Idle System Antifreeze Protection to -34 F (-37 C) Enclosed Fan Guard Dual Element Dry-type Air Filter with Restriction Indicator Full Flow Oil Filter Double Fuel Filter Water Separator Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net Glow Plug Start Aid 50-Amp Alternator - 24 Volt 500 Hour Engine Oil Change Interval Engine Oil Drain Coupler Isolation Mounted For use only in areas where EPA Interim Tier 4/EU Stage IIIB is required. DECALS / OPERATOR MANUALS 1090 $10,566.00 English Decals and Customer Delivery Packet, IT4 1600 No Charge English Decals and Customer Delivery Packet, S2 1605 No Charge MACHINE CONNECTIVITY Machine connectivity functions require cellular coverage. Usage of ZXLink System requires customer's acceptance of the terms of the John Deere Telematics System Contract. Option availability limited by specific geographical regions. Please refer to region specific price pages for appropriate ordering codes.
Page 3 of 9 2/20/2015 ZXLink Ultimate Cellular for the Americas 1700 In Base Price Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway (MTG), and ZXLink Ultimate activation. ZXLink utilizes cellular and satellite technology infrastructure that is outside the control of John Deere. Changes to that infrastructure may require customers to purchase compatible ZXLink hardware to restore functionality. Includes 3 year subscription. Annual subscription renewal required after 3 years for continued functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to www.stellarsupport.com to renew or update ZXLink subscriptions. Use of this service, and all rights and obligations of John Deere and the Customer (as identified in the applicable agreement), are governed by the terms and conditions outlined in the applicable Services and Software agreements available at www.johndeere.com/agreements. If these terms and conditions are not agreeable do not proceed and do not use the service. ZXLink Ultimate CS for Brazil 1705 In Base Price Includes ZXLink hardware, integrated cab wiring harness, antenna, modular telematics gateway and ZXLink web access and data storage. Customers must purchase a SIM card and 3 year plan from a local telecom provider to enable ZXLink. ZXLink Ultimate Cellular for the Americas - 5 Years 1710 $1,320.00 Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway (MTG), and ZXLink Ultimate activation. ZXLink utilizes cellular and satellite technology infrastructure that is outside the control of John Deere. Changes to that infrastructure may require customers to purchase compatible ZXLink hardware to restore functionality. Includes 5 year subscription. Annual subscription renewal required after 5 years for continued functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to www.stellarsupport.com to renew or update ZXLink subscriptions. Use of this service, and all rights and obligations of John Deere and the Customer (as identified in the applicable agreement), are governed by the terms and conditions outlined in the applicable Services and Software agreements available at www.johndeere.com/agreements. If these terms and conditions are not agreeable do not proceed and do not use the service. TRACK SHOES 600 mm (24 In.) Triple Semi Grousers without Backfill Blade Recommended for rocky terrain, hard ground and stumps. 3200 In Base Price 600 mm (24 In.) Triple Semi Grousers with 2590 mm (8'6") wide Backfill Blade 3205 $14,215.00 Recommended for rocky terrain, hard ground and stumps. 700 mm (28 In.) Triple Semi Grousers without Backfill Blade 3250 $671.00 Recommended for general conditions and soft terrain. 700 mm (28 In.) Triple Semi Grousers with 2690 mm (8'10") wide Backfill Blade 3255 $14,885.00 Recommended for general conditions and soft terrain.
Page 4 of 9 2/20/2015 600 mm (24 In.) Rubber Crawler Pads without Backfill Blade 3260 $10,601.00 Rubber pads are laminated to track shoe. This option requires a long lead time, contact your dealer for availability of this option. 600 mm (24 In.) Rubber Crawler with 2590 mm (8'6") wide Backfill Blade 3265 $24,816.00 Rubber pads are laminated to track shoe. This option requires a long lead time, contact your dealer for availability of this option. SEATS Seat, Standard Mechanical 4125 In Base Price Seat, Heated Air-Suspension 4130 $801.00 BOOM Less Boom Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom. Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins. Requires code 7001, "Less Arm". The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is recommended 6801 In Base Price One Piece Boom with Arm Cylinder and Plumbing 6835 $13,722.00 ARMS Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses Hydraulic Filter Restriction Indicator Recommended. Requires code 8001, Less Buckets. 7001 In Base Price 2.52 M (8 ft. 3 in.) Arm with Bucket Cylinder and Linkage 7140 $8,806.00 3.01 M (9 ft. 11 in.) Arm with Bucket Cylinder and Linkage 7180 $10,111.00 AUXILIARY HYDRAULICS Less Auxiliary Hydraulics 7401 In Base Price Auxiliary High-Flow Hydraulic Lines for 2.52 M Arm w/ 2- Way Foot Controller Auxiliary High-Flow Hydraulic Lines for 2.52 M Arm w/ 2- Way Foot Controller, S2 Auxiliary High-Flow Hydraulic Lines for 3.01 M Arm w/ 2- Way Foot Controller 7420 $6,258.00 7423 $6,258.00 7430 $6,385.00 Auxiliary High-Flow Hydraulic Lines for 3.01 M Arm w/ 2-7433 $6,385.00
Page 5 of 9 2/20/2015 Way Foot Controller, S2 Auxiliary High-Flow Hydraulic Lines Only for 2.52 M Arm 7440 $4,157.00 Requires a control circuit such as a foot controller or the standard right-hand control handle with (2) switches. Also order a solenoid kit. Auxiliary High-Flow Hydraulic Lines Only for 2.52 M Arm, S2 7443 $4,157.00 Requires a control circuit such as a foot controller or the standard right-hand control handle with (2) switches. Also order a solenoid kit. Auxiliary High-Flow Hydraulic Lines Only for 3.01 M Arm 7450 $4,284.00 Requires a control circuit such as a foot controller or the standard right-hand control handle with (2) switches. Also order a solenoid kit. Auxiliary High-Flow Hydraulic Lines Only for 3.01 M Arm, S2 7453 $4,284.00 BUCKETS Requires a control circuit such as a foot controller or the standard right-hand control handle with (2) switches. Also order a solenoid kit. Less Buckets Includes bucket mounting pins. 8001 In Base Price 24 In. (600 mm), 0.48 Yd3 (0.37 M3) Heavy-Duty Bucket 8410 $4,708.00 Includes Four (4) Esco Ultralock Teeth 30 In. (750 mm), 0.65 Yd3 (0.50 M3) Heavy-Duty Bucket 8420 $5,096.00 Includes Four (4) Esco Ultralock Teeth 36 In. (900 mm), 0.81 Yd3 (0.62 M3) Heavy-Duty Bucket 8430 $5,616.00 Includes Five (5) Esco Ultralock Teeth Optional - Select as desired OPTIONAL EQUIPMENT--ORDER AS DESIRED Light Package 9150 $741.00 Additional 2 Cab lights, with 1 Right hand Boom Light. Mechanical Control-Pattern Selector 9500 $1,359.00 Mechanical Control-Pattern Selector, S2 9502 $1,359.00 Rear View Camera 9600 $1,780.00 Chrome Exhaust 9700 $387.00 Special Export Preperation-- Do not install front for shipping 9803 No Charge For Export Containerization Non-Export Rust Preventive Coating 9909 $231.00
Page 6 of 9 2/20/2015 Boom Cylinders with Plumbing to Main Frame 9010 $5,009.00 Requires 6801, Less Boom, and Code 7001, Less Arm. Non-English Operator's Manuals Translated Customer Delivery Packets can be ordered using the John Deere Technical Information Bookstore at http://www.johndeeretechinfo.com at no charge. The Translated Delivery Packets include the Operator Manual, Decal Kit, Warranty Information Booklet, and Uptime Maintenance Planner. Search for and order the Translated Delivery Packets by model and language that meets your customer requirements. A listing of all Translated Delivery Packets available can be found by selecting Translated Delivery Packets from the Manual Type dropdown list. Technical support is available by calling 1-866-213-3373. Machine Information Center, PLUS Machine Information Center (MIC) kits can be ordered using the Technical Information Web Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC. MIC_Plus is for certain customers that would like the ability to perform their own diagnostics as well as downloading MIC data using an approved PDA. This software is not available directly to customers and Service Department should be advised before providing MIC_Plus to customers. There are 2 types of MIC_Plus kits available: 1. Complete MIC_Plus (Customer Diagnostics) - Includes PDA, Software and Cables 2. Update MIC_Plus (Customer Diagnostics) - Includes only Diagnostics cable and latest software Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical support for using the Technical Information Web Bookstore can be obtained by calling 1-866-213-3373. Machine Information Center, Standard Machine Information Center (MIC) kits can be ordered using the Technical Information Web Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC. MIC Download is used for downloading MIC controller only using an approved PDA. Customer then transfers information to PC for viewing stored information. There are 2 types of kits available for customers: 1. Complete MIC for Customer Download - Includes PDA, Software and Cables 2. Update MIC for Customer Download - Includes only download cable and latest software Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical support for using the Technical Information Web Bookstore can be obtained by calling 1-866-213-3373. ATTACHMENTS FOR FIELD CONVERSION F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may require additional parts for a complete installation. Prior to ordering, check the installation instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment installation instruction bulletin for additional parts. Exception to above note is FRONTIER Dealer Installed Kits. All attachments are sold as a quantity of one. Buckets, Heavy-Duty: Buckets come standard with horizontal wear strips. Vertical wear strips in lieu of horizontal are available at no additional charge. The switch to vertical wear strips MUST be indicated in the comments section of your order. 24 In (610 mm), 0.48 yd3 (0.37 M3) Heavy-Duty Bucket Includes Four (4) Esco Ultralock Teeth AT339032 $4,021.00
Page 7 of 9 2/20/2015 30 In (762 mm), 0.65 yd3 (0.50 M3) Heavy-Duty Bucket AT339034 $4,387.00 Includes Four (4) Esco Ultralock Teeth 36 In (914 mm), 0.81 yd3 (0.62 M3) Heavy-Duty Bucket AT339036 $4,879.00 Includes Five (5) Esco Ultralock Teeth 42 In (1067 mm), 0.99 yd3 (0.76 M3) Heavy-Duty Bucket AT339038 $5,316.00 Includes Five (5) Esco Ultralock Teeth Guards: Cab FOPS Guard AT390802 $2,584.00 FOPS Level II, ISO 10262 Certified Hydraulic Couplers: Hydraulic Quick Coupler AT343227 $7,746.00 Installation Charge for Hydraulic Coupler AT345608 $1,360.00 Installation Charge Order also requires attachment part number, SHIP-TO address for Paladin Custom Works, AND reference related machine order number. The related machine order must reference the attachment order number. Order code available only for Kernersville, North Carolina installations. Hydraulic Thumb Kits: Please click on the following link to access the freight rate tables. Deere/Hitachi Hydraulic Thumb Installation AT339844 $1,928.00 Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC. Hydraulic Thumb Kit, Direct AT379640 $8,000.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulic Thumb Kit, Direct for Couplers AT379641 $8,000.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulic Thumb Kit, Progressive AT379642 $10,076.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulic Thumb Kit, Progressive for Couplers AT379643 $8,396.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing.
Page 8 of 9 2/20/2015 Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulics: Auxiliary High-Flow Lines for 2.52 M Arm AT448514 $3,533.00 For S2 engines only. Auxiliary High-Flow Lines for 2.52 M Arm AT418447 $3,533.00 Auxiliary High-Flow Lines for 3.01 M Arm AT418449 $3,654.00 Auxiliary High-Flow Lines for 3.01 M Arm AT448515 $3,654.00 For S2 engines only. Auxiliary Hydraulics, Attachment Combination Kit AT343969 $577.00 Requires Auxiliary High-Flow Hydraulic Lines. Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow lines, ready for operation. Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses the existing stop valves to shut-off thumb operation when not in use. Control Handle for Auxiliary Hydraulics, Left-Hand AT327652 $515.00 Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size excavators. Requires control solenoid for either 1-way or 2-way auxiliary hydraulics. Recommended for use with auxiliary hydraulic lines. Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch AT390742 $931.00 Does not use the monitor for flow control. Does not require solenoids for auxiliary hydraulics. Includes foot switch, solenoid, relays, wiring, and hoses. Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch AT446155 $931.00 Does not use the monitor for flow control. Does not require solenoids for auxiliary hydraulics. Includes foot switch, solenoid, wiring, and hoses. Control Solenoids for 2-Way Auxiliary Hydraulics AT390718 $784.00 Monitor can be used to control hydraulic flow. Can be used with either right-hand or left-hand control handle. Control Solenoids for 2-Way Auxiliary Hydraulics AT445467 $784.00 Monitor can be used to control hydraulic flow. Can be used with either right-hand or left-hand control handle. Foot Control, Two-Way Hydraulics AT418450 $1,970.00 Hydraulic Filter Restriction Indicator Kit AT339802 $774.00 Mechanical Control Pattern Selector Kit AT418446 $987.00 Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control pattern.
Page 9 of 9 2/20/2015 Some excavators require additional parts. Mechanical Control Pattern Selector Kit AT448516 $987.00 For S2 engines only. Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control pattern. Some excavators require additional parts. Single Pedal Propel Kit AT390776 $2,080.00 Operator Environment: Guard, Lower Front Window ISO Level II AT390824 $1,048.00 Guard, Upper Front Window ISO Level II AT390823 $788.00 MP3 Player Field Kit ETN93549 $160.00 Work Lights AT396663 $726.00 Additional 2 Cab lights, with 1 Right hand Boom Light. Overall Vehicle: Rear View Camera AT422264 $1,679.00 Vandal Cover Kit AT390721 $2,208.00 REFERRAL ATTACHMENTS G.R. Mfg.: G.R. Manufacturing, Inc. * Kits listed below must be ordered through John Deere. * F.O.B. Trussville, Alabama * All kits include installation instructions * All warranty, repair parts, technical support and assistance, and sales support and assistance will be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer and G.R. Manufacturing, Inc. G.R. Manufacturing, Inc. 4800 Commerce Drive Trussville, Alabama 35173 Phone: (800)841-8001 Fax: (205)655-8005 Counterweight, Bottom Mount, 1200 lbs. AT430877 $3,100.00 Parts are primed only (contact GR Mfg for paint color). Cannot be ordered for blade units. Front Window Guard, Polycarbonate ETN85142 $2,520.00 Rear Work Lights Package AT430784 $1,246.00 Slant Top Rub Rails AT430873 $1,645.00 Copyright 1996-2014 Deere & Company. All Rights Reserved. About Our Site Privacy and Data Legal
https://configurator-stage.deere.com/servlet/com.deere.u90947.eproducts.view.servlets.equi... Page 1 of 6 2/6/2015 Current Date 06Feb2015 ZAXIS 135 US-5 EXCAVATOR ENGINE: Isuzu AI-4JJ1X - Certified IT4 / Stage IIIB emissions 93 Net Peak Power (ISO9249) Turbocharger Electronic Engine Control Unit Auto-Idle System Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net Antifreeze Protection to -34 degrees F (-37 degrees C) Enclosed Fan Guard Dual Element Dry-type Air Filter with Restriction Indicator Full Flow Oil Filter Double Fuel Filter Water Separator Glow Plug Start Aid 50-Amp Alternator - 24 Volt 500 Hour Engine Oil Change Interval Isolation Mounted HYDRAULICS: Open Center, Load Sensing with Variable Displacement Pumps Hydraulic Pilot Controls Axial Piston Swing Motor Multiple Wet Disk Swing Brake Auxiliary Valve Section Adjustable Flow for Attachments Through Monitor Boom and Arm Reduced Drift Valves Hydraulic Tank Site Gauge 5,000 Hour Hydraulic Oil Change Interval UNDERCARRIAGE: Two Speed Propel with Auto- Shift Spring Applied Hydraulic Released Propel Brake UPPER STRUCTURE: Right and Left Mirrors Toolbox Vandal Locks for: Cab Door Service Doors Fuel Cap Tool Box Counterweight, 8,110 lbs. (3,680 kg) Work Lights: One Mounted on Frame One Mounted on Boom Remote Mounted Engine Oil and Fuel Filters FRONT ATTACHMENT: Oil Impregnated Bushings Reinforced Resin Thrust Plates Tungsten Carbide Thermal Coating on arm to Bucket Joint Centralized Lubrication System Dirt Seals on Bucket Pins Less Boom Less Arm Less Bucket OPERATOR'S STATION: ZXLink Ultimate Machine Monitoring System w/ 3-year Message Service (Available in United States and Canada only) Adjustable Control Positions (Levers to Seat, Seat to Pedals) 4" Arm Rests Attached to Side Consoles Pilot Control Shut-Off Lever Short Stroke, Low Effort Pilot Levers Switches for Auxiliary Multiple Language Capability Maintenance Tracking Engine Coolant Temperature Gauge Engine Coolant Temperature Warning Indicator with Audible Alarm Engine Oil Pressure Warning Indicator with Audible Alarm Fuel Gauge with Low Fuel Indicator Work Mode Indicator Auto Idle Indicator Alternator Charge Indicator Air Filter Restriction Indicator Fault Code Alert Indicator Check Engine Indicator Wiper Mode Indicator Work Lights On Indicator Fuel Rate Display Clock Hour Meter Mode Selection: One Work Mode Three Power Modes Numerous Attachment Modes Auto-Climate Control/Air Conditioner, Heater with Pressurizer AM-FM Radio Rear View Camera Machine Information Center (MIC) Windshield Wiper/Washer with Intermittent Speed 12V-60W, 5 Amp Cell Phone Power Outlet 2 In. Retractable Seat Belt Tinted Safety Glass Hot/Cold Box Compartment Horn Cup Holder Interior Light
https://configurator-stage.deere.com/servlet/com.deere.u90947.eproducts.view.servlets.equi... Page 2 of 6 2/6/2015 Axial Piston Propel Motors Propel Motor Shields Planetary Final Drives Sealed Track Chain Front Track Guides Provisions for Tie Downs X-Frame Car Body Hydraulic Track Adjuster Seven Lower Rollers One Upper Rollers Hydraulic Control on RH Pilot Lever Deluxe Adjustable Cloth Seat with Suspension, Reclining Backrest, Headrest, and Adjustable Lumbar Support Multifunction, Color LCD Monitor System with: Diagnostic Capability Systems Monitoring Capability Coat Hook Floor Mat Motion Alarm with Cancel Switch Transparent Tinted Roof Hatch with Sunshade Four Fluid-Filled Elastic Mounts Easy Access Air Conditioning Filter Required - You must select one from each category BASE MACHINE F.O.B. US/Canadian Port of Entry except where noted. See DEALER-INSTALLED ATTACHMENT section for additional source notes. ZAXIS 135 US-5 EXCAVATOR 05V0FF $176,595.00 MACHINE CONNECTIVITY Machine connectivity functions require cellular coverage. Usage of ZXLink System requires customer's acceptance of the terms of the John Deere Telematics System Contract. Option availability limited by specific geographical regions. Please refer to region specific price pages for appropriate ordering codes. ZXLink Ultimate Cellular for the Americas Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway (MTG), and ZXLink Ultimate activation. ZXLink utilizes cellular and satellite technology infrastructure that is outside the control of John Deere. Changes to that infrastructure may require customers to purchase compatible ZXLink hardware to restore functionality. Includes 3 year subscription. Annual subscription renewal required after 3 years for continued functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to www.stellarsupport.com to renew or update ZXLink subscriptions. Use of this service, and all rights and obligations of John Deere and the Customer (as identified in the applicable agreement), are governed by the terms and conditions outlined in the applicable Services and Software agreements available at www.johndeere.com/agreements. If these terms and conditions are not agreeable do not proceed and do not use the service. 1700 In Base Price ZXLink Ultimate Cellular for the Americas - 5 Years 1710 $1,320.00 Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway (MTG), and ZXLink Ultimate activation. ZXLink utilizes cellular and satellite technology infrastructure that is outside the control of John Deere. Changes to that infrastructure may require customers to purchase compatible ZXLink hardware to restore functionality. Includes 5 year subscription. Annual subscription renewal required after 5 years for continued functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to www.stellarsupport.com to renew or update ZXLink
https://configurator-stage.deere.com/servlet/com.deere.u90947.eproducts.view.servlets.equi... Page 3 of 6 2/6/2015 subscriptions. Use of this service, and all rights and obligations of John Deere and the Customer (as identified in the applicable agreement), are governed by the terms and conditions outlined in the applicable Services and Software agreements available at www.johndeere.com/agreements. If these terms and conditions are not agreeable do not proceed and do not use the service. TRACK SHOES 600 mm (24 In.) Steel Tracks less Backfill Blade 3200 In Base Price 600 mm (24 In.) Steel Tracks w/ 2490 mm Backfill Blade 3205 $14,724.00 700 mm (28 In.) Steel Tracks less Backfill Blade 3250 $685.00 700 mm (28 In.) Steel Tracks w/ 2690 mm Backfill Blade 3255 $15,410.00 500 mm (20 In.) Rubber Crawler Pads less Backfill Blade 3260 $11,150.00 Rubber pads are laminated to track shoe. This option requires a long lead time, contact your dealer for availability of this option. 500 mm (20 In.) Rubber Crawler Pads w/ 2490 mm Backfill Blade 3265 $25,874.00 Rubber pads are laminated to track shoe. This option requires a long lead time, contact your dealer for availability of this option. BOOM Less Boom Includes Boom Cylinders, Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins. Requires code 7001, "Less Arm". The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is recommended. 6801 In Base Price One Piece Boom with Arm Cylinder and Plumbing 6835 $14,217.00 ARMS Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses Hydraulic Filter Restriction Indicator Recommended. Requires code 8001, Less Buckets. 7001 In Base Price 2.52 M (8 ft. 3 in.) Arm with Bucket Cylinder and Linkage 7140 $8,981.00 3.01 M (9 ft. 11 in.) Arm with Bucket Cylinder and Linkage 7160 $10,312.00 Optional - Select as desired ATTACHMENTS FOR FIELD CONVERSION F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may require additional parts for a complete installation. Prior to ordering, check the installation instructions by going to www.johndeeretechinfo.com and clicking on
https://configurator-stage.deere.com/servlet/com.deere.u90947.eproducts.view.servlets.equi... Page 4 of 6 2/6/2015 Library, or by clicking on this Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment installation instruction bulletin for additional parts. Exception to above note is FRONTIER Dealer Installed Kits. Buckets, Heavy-Duty: Buckets come standard with horizontal wear strips. Vertical wear strips in lieu of horizontal are available at no additional charge. The switch to vertical wear strips MUST be indicated in the comments section of your order. 24 In (610 mm), 0.48 yd3 (0.37 M3) Heavy-Duty Bucket AT339050 $4,021.00 Includes Four (4) Esco Ultralock Teeth 30 In (762 mm), 0.65 yd3 (0.50 M3) Heavy-Duty Bucket AT339052 $4,387.00 Includes Four (4) Esco Ultralock Teeth 36 In (914 mm), 0.81 yd3 (0.62 M3) Heavy-Duty Bucket AT339054 $4,879.00 Includes Five (5) Esco Ultralock Teeth 42 In (1067 mm), 0.99 yd3 (0.76 M3) Heavy-Duty Bucket AT339056 $5,316.00 Includes Five (5) Esco Ultralock Teeth Buckets, Side Cutters: Edge Protector Kit AT342511 $606.00 Side-Cutter Kit, 3 inch AT342512 $628.00 Buckets, Ditching: 60 In (1524 mm), 0.83 yd3 (0.63 M3) Ditching Bucket AT339058 $3,674.00 Hydraulic Couplers: Hydraulic Quick Coupler AT343228 $7,746.00 Installation Charge for Hydraulic Coupler AT345608 $1,360.00 Installation Charge Order also requires attachment part number, SHIP-TO address for Paladin Custom Works, AND reference related machine order number. The related machine order must reference the attachment order number. Order code available only for Kernersville, North Carolina installations. Hydraulic Thumb Kits: Please click on the following link to access the freight rate tables. Deere/Hitachi Hydraulic Thumb Installation AT339844 $1,928.00 Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC. Hydraulic Thumb Kit, Direct AT379640 $8,000.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement.
https://configurator-stage.deere.com/servlet/com.deere.u90947.eproducts.view.servlets.equi... Page 5 of 6 2/6/2015 Hydraulic Thumb Kit, Direct for Couplers AT379641 $8,000.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulic Thumb Kit, Progressive AT379642 $10,076.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulic Thumb Kit, Progressive for Couplers AT379643 $8,396.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulics: Auxiliary High-Flow Lines for 3.01 M Arm AT421684 $3,654.00 Auxiliary Hydraulics, Attachment Combination Kit AT343969 $577.00 Requires Auxiliary High-Flow Hydraulic Lines. Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow lines, ready for operation. Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses the existing stop valves to shut-off thumb operation when not in use. Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch AT354488 $931.00 Does not use the monitor for flow control. Does not require solenoids for auxiliary hydraulics. Includes foot switch, solenoid, relays, wiring, and hoses. Control Solenoids for 2-Way Auxiliary Hydraulics AT342526 $784.00 Monitor can be used to control hydraulic flow. Can be used with either right-hand or left-hand control handle. Foot Control, Two-Way Hydraulics AT421633 $1,970.00 Hydraulic Filter Restriction Indicator Kit AT334168 $774.00 Mechanical Control Pattern Selector Kit AT421728 $987.00 Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control pattern. Some excavators require additional parts. Operator Environment: MP3 Player Field Kit ETN93549 $160.00 Work Lights AT396663 $726.00 Additional 2 Cab lights, with 1 Right hand Boom Light.
https://configurator-stage.deere.com/servlet/com.deere.u90947.eproducts.view.servlets.equi... Page 6 of 6 2/6/2015 REFERRAL ATTACHMENTS G.R. Mfg.: G.R. Manufacturing, Inc. * Kits listed below must be ordered through John Deere. * F.O.B. Trussville, Alabama * All kits include installation instructions * All warranty, repair parts, technical support and assistance, and sales support and assistance will be the responsibility of G.R. Manufacturing, Inc., and will be handled directly between the Dealer and G.R. Manufacturing, Inc. G.R. Manufacturing, Inc. 4800 Commerce Drive Trussville, Alabama 35173 Phone: (800)841-8001 Fax: (205)655-8005 Rear Work Lights Package AT430784 $1,246.00 Copyright 1996-2014 Deere & Company. All Rights Reserved. About Our Site Privacy and Data Legal
Page 1 of 9 3/31/2015 Current Date 31Mar2015 ZAXIS 160 LC-5 EXCAVATOR HYDRAULICS: Open Center, Load Sensing with Variable Displacement Pumps Hydraulic Pilot Controls Axial Piston Swing Motor Multiple Wet Disk Swing Brake Auxiliary Valve Section Adjustable Flow for Attachments Through Monitor Boom and Arm Reduced Drift Valves Power Boost Auto Power Lift Hydraulic Tank Site Gauge 5,000 Hour Hydraulic Oil Change Interval UNDERCARRIAGE: Two Speed Propel with Auto- Shift Axial Piston Propel Motors Propel Motor Shields Planetary Final Drives Sealed Track Chain Front and Center Track Guides Provisions for Tie Downs X-Frame Car Body Hydraulic Track Adjuster Eight Lower Rollers Two Upper Rollers Spring Applied Hydraulic Released Propel Brake UPPER STRUCTURE: *Right, Left, and Counterweight Mirrors(3) Toolbox Vandal Locks for: Cab Door Service Doors Fuel Cap Tool Box Counterweight, 7,077 lbs. (3,210 kg) FRONT ATTACHMENT: Oil Impregnated Bushings Reinforced Resin Thrust Plates Tungsten Carbide Thermal Coating on arm to Bucket Joint Centralized Lubrication System Dirt Seals on Bucket Pins Less Boom Less Arm Less Bucket OPERATOR'S STATION: ZXLink Ultimate Machine Monitoring System w/ 3-year Message Service (Available in United States and Canada only) Adjustable Control Positions (Levers to Seat, Seat to Pedals) 4" Arm Rests Attached to Side Consoles Pilot Control Shut-Off Lever Short Stroke, Low Effort Pilot Levers Switches for Auxiliary Hydraulic Control on RH Pilot Lever Deluxe Adjustable Cloth Seat with Suspension, Reclining Backrest, Headrest, and Adjustable Lumbar Support Multifunction, Color LCD Monitor System with: Diagnostic Capability Systems Monitoring Capability Multiple Language Capability Maintenance Tracking Engine Coolant Temperature Gauge Engine Coolant Temperature Engine Oil Pressure Warning Indicator with Audible Alarm Fuel Gauge with Low Fuel Indicator Work Mode Indicator Auto Idle Indicator Alternator Charge Indicator Air Filter Restriction Indicator Fault Code Alert Indicator Check Engine Indicator Wiper Mode Indicator Work Lights On Indicator Fuel Rate Display Clock Hour Meter Mode Selection: One Work Mode Three Power Modes Numerous Attachment Modes Auto-Climate Control/Air Conditioner, Heater with Pressurizer AM-FM Radio Machine Information Center (MIC) Windshield Wiper/Washer with Intermittent Speed 12V-60W, 5 Amp Cell Phone Power Outlet 2 In. Retractable Seat Belt Tinted Safety Glass Hot/Cold Box Compartment Horn Two Cup Holders Interior Light Coat Hook Floor Mat Motion Alarm with Cancel Switch Transparent Tinted Roof Hatch with Sunshade Four Fluid-Filled Elastic Mounts
Page 2 of 9 3/31/2015 Work Lights: One Mounted on Frame One Mounted on Boom Remote Mounted Engine Oil and Fuel Filters Warning Indicator with Audible Alarm Easy Access Air Conditioning Filter Required - You must select one from each category BASE MACHINE F.O.B Kernersville, North Carolina for Complete Machine. See DEALER-INSTALLED ATTACHMENT section for additional source notes. ZAXIS 160 LC-5 EXCAVATOR 05W0FF $179,447.00 ENGINE *Isuzu AM-4JJ1, Certified to IT4 / Stage IIIB emissions 122 hp Net Peak Power (ISO9249) Turbocharger Electronic Engine Control Unit Auto-Idle System Antifreeze Protection to -34 F (-37 C) Enclosed Fan Guard Dual Element Dry-type Air Filter with Restriction Indicator Full Flow Oil Filter Double Fuel Filter Water Separator Side by Side by Side Radiator, Oil Cooler, Intercooler with Dust Net Glow Plug Start Aid 50-Amp Alternator - 24 Volt 500 Hour Engine Oil Change Interval Engine Oil Drain Coupler Isolation Mounted For use only in areas where EPA Interim Tier 4/EU Stage IIIB is required. DECALS / OPERATOR MANUALS 1090 $12,697.00 English Decals and Customer Delivery Packet, IT4 1600 No Charge English Decals and Customer Delivery Packet, S2 1605 No Charge MACHINE CONNECTIVITY Machine connectivity functions require cellular coverage. Usage of ZXLink System requires customer's acceptance of the terms of the John Deere Telematics System Contract. Option availability limited by specific geographical regions. Please refer to region specific price pages for appropriate ordering codes.
Page 3 of 9 3/31/2015 ZXLink Ultimate Cellular for the Americas 1700 In Base Price Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway (MTG), and ZXLink Ultimate activation. ZXLink utilizes cellular and satellite technology infrastructure that is outside the control of John Deere. Changes to that infrastructure may require customers to purchase compatible ZXLink hardware to restore functionality. Includes 3 year subscription. Annual subscription renewal required after 3 years for continued functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to www.stellarsupport.com to renew or update ZXLink subscriptions. Use of this service, and all rights and obligations of John Deere and the Customer (as identified in the applicable agreement), are governed by the terms and conditions outlined in the applicable Services and Software agreements available at www.johndeere.com/agreements. If these terms and conditions are not agreeable do not proceed and do not use the service. ZXLink Ultimate Cellular for the Americas - 5 Years 1710 $1,320.00 Includes ZXLink hardware: integrated cab wiring harness, antenna, modular telematics gateway (MTG), and ZXLink Ultimate activation. ZXLink utilizes cellular and satellite technology infrastructure that is outside the control of John Deere. Changes to that infrastructure may require customers to purchase compatible ZXLink hardware to restore functionality. Includes 5 year subscription. Annual subscription renewal required after 5 years for continued functionality. ZXLink customer account must be created to access ZXLink Ultimate data. Go to www.stellarsupport.com to renew or update ZXLink subscriptions. Use of this service, and all rights and obligations of John Deere and the Customer (as identified in the applicable agreement), are governed by the terms and conditions outlined in the applicable Services and Software agreements available at www.johndeere.com/agreements. If these terms and conditions are not agreeable do not proceed and do not use the service. TRACK SHOES 600 mm (24 In.) Triple Semi-Grouser Shoes Recommended for rocky terrain, hard ground and stumps. 3200 In Base Price 700 mm (28 In.) Triple Semi-Grouser Shoes 3250 $1,119.00 Recommended for general conditions and soft terrain. SEATS Seat, Standard Mechanical 4125 In Base Price Seat, Heated Air-Suspension 4130 $801.00 BOOM Less Boom Excludes Arm Cylinder, Boom Cylinders and Plumbing on Boom. Includes Pin Connecting Boom to Mainframe and the Two Boom Cylinder Pins. Requires code 7001, "Less Arm". The "Hydraulic Filter Restriction Indicator" in DEALER-INSTALLED ATTACHMENTS is recommended 6801 In Base Price
Page 4 of 9 3/31/2015 One Piece Boom with Arm Cylinder and Plumbing 6835 $15,905.00 ARMS Less Arm, Bucket Cylinder, Bucket Linkage and All Attaching Pins and Hoses Hydraulic Filter Restriction Indicator Recommended. 7001 In Base Price 2.6 M (8 ft. 6 in.) Arm with Bucket Cylinder and Linkage 7115 $10,831.00 3.1 M (10 ft. 2 In.) Arm with Bucket Cylinder and Linkage 7180 $12,369.00 AUXILIARY HYDRAULICS Less Auxiliary Hydraulics 7401 In Base Price Auxiliary High-Flow Hydraulic Lines for 2.6 M Arm w/ 2-Way Foot Controller Auxiliary High-Flow Hydraulic Lines for 2.6 M Arm w/ 2-Way Foot Controller, S2 Auxiliary High-Flow Hydraulic Lines for 3.1 M Arm w/ 2-Way Foot Controller Auxiliary High-Flow Hydraulic Lines for 3.1 M Arm w/ 2-Way Foot Controller, S2 Auxiliary High-Flow Hydraulic Lines Only for 2.6 M Arm 7420 $6,835.00 7421 $6,835.00 7430 $6,988.00 7431 $6,988.00 7440 $4,794.00 Requires a control circuit such as a foot controller or the standard right-hand control handle with (2) switches. Also order a solenoid kit. Auxiliary High-Flow Hydraulic Lines Only for 2.6 M Arm, S2 7441 $4,794.00 Requires a control circuit such as a foot controller or the standard right-hand control handle with (2) switches. Also order a solenoid kit. Auxiliary High-Flow Hydraulic Lines Only for 3.1 M Arm 7450 $4,948.00 Requires a control circuit such as a foot controller or the standard right-hand control handle with (2) switches. Also order a solenoid kit. Auxiliary High-Flow Hydraulic Lines Only for 3.1 M Arm, S2 7451 $4,948.00 BUCKETS Requires a control circuit such as a foot controller or the standard right-hand control handle with (2) switches. Also order a solenoid kit. Less Buckets Includes bucket mounting pins. 8001 In Base Price 30 In. (762 mm), 0.65 Yd3 (0.50 M3) Heavy-Duty Bucket 8420 $6,330.00 Includes Four (4) Esco Ultralock Teeth
Page 5 of 9 3/31/2015 36 In. (914 mm), 0.81 Yd3 (0.62 M3) Heavy-Duty Bucket 8430 $6,871.00 Includes Five (5) Esco Ultralock Teeth 42 In. (1067 mm) 0.99 Yd3 (0.76 M3), Heavy-Duty Bucket 8440 $7,401.00 Includes Five (5) Esco Ultralock Teeth Optional - Select as desired OPTIONAL EQUIPMENT--ORDER AS DESIRED Boom Cylinders with Plumbing to Main Frame 9010 $5,959.00 Requires 6801, Less Boom, and Code 7001, Less Arm. Light Package 9150 $741.00 Additional 2 Cab lights, with 1 Right hand Boom Light. Mechanical Control-Pattern Selector 9500 $1,359.00 Mechanical Control-Pattern Selector, S2 9501 $1,359.00 Rear View Camera 9600 $1,780.00 Non-Export Rust Preventive Coating 9909 $248.00 Chrome Exhaust 9700 $399.00 Machine Information Center, Standard Machine Information Center (MIC) kits can be ordered using the Technical Information Web Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC. MIC Download is used for downloading MIC controller only using an approved PDA. Customer then transfers information to PC for viewing stored information. There are 2 types of kits available for customers: 1. Complete MIC for Customer Download - Includes PDA, Software and Cables 2. Update MIC for Customer Download - Includes only download cable and latest software Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical support for using the Technical Information Web Bookstore can be obtained by calling 1-866-213-3373. Machine Information Center, PLUS Machine Information Center (MIC) kits can be ordered using the Technical Information Web Bookstore at http://www.jdtechinfo.com. To locate these kits, use a search word of MIC. MIC_Plus is for certain customers that would like the ability to perform their own diagnostics as well as downloading MIC data using an approved PDA. This software is not available directly to customers and Service Department should be advised before providing MIC_Plus to customers. There are 2 types of MIC_Plus kits available: 1. Complete MIC_Plus (Customer Diagnostics) - Includes PDA, Software and Cables 2. Update MIC_Plus (Customer Diagnostics) - Includes only Diagnostics cable and latest software Technical support for the Customer MIC program is the responsibility of the selling dealer. Technical support for using the Technical Information Web Bookstore can be obtained by calling 1-866-213-3373. ZXLINK Machine Monitoring System Standard ZXLINK Machine Monitoring System Standard
Page 6 of 9 3/31/2015 The configurator does not automatically order and add ZXLINK to the Machine Quote. Need to MANUALLY add ZXLINK price to Machine Quote. Click on (ZXLINK Machine Monitoring System) Hyperlink above to access ZXLINK information page. Only for use in the United States and Canada at this time. ATTACHMENTS FOR FIELD CONVERSION F.O.B. Dubuque, Iowa for dealer-installed kits, except where noted. Some of the following kits may require additional parts for a complete installation. Prior to ordering, check the installation instructions by going to www.johndeeretechinfo.com and clicking on Library, or by clicking on this Hyperlink ( Installation Bulletin Search ), and insert the AT number to retrieve the attachment installation instruction bulletin for additional parts. Exception to above note is FRONTIER Dealer Installed Kits. All attachments are sold as a quantity of one. Buckets, Heavy-Duty: Buckets come standard with horizontal wear strips. Vertical wear strips in lieu of horizontal are available at no additional charge. The switch to vertical wear strips MUST be indicated in the comments section of your order. 24 In (610 mm), 0.48 yd3 (0.37 M3) Heavy-Duty Bucket AT339089 $5,070.00 Includes Four (4) Esco Ultralock Teeth 30 In (762 mm), 0.65 yd3 (0.50 M3) Heavy-Duty Bucket AT339091 $5,553.00 Includes Four (4) Esco Ultralock Teeth 36 In (914 mm), 0.81 yd3 (0.62 M3) Heavy-Duty Bucket AT339093 $6,064.00 Includes Five (5) Esco Ultralock Teeth 42 In (1067 mm), 0.99 yd3 (0.76 M3) Heavy-Duty Bucket AT339095 $6,566.00 Includes Five (5) Esco Ultralock Teeth 48 In (1220 mm), 1.18 yd3 (0.90 M3) Heavy-Duty Bucket AT351718 $7,329.00 Buckets, Side Cutters: Edge Protector Kit AT342511 $606.00 Side-Cutter Kit, 3 inch AT342512 $628.00 Guards: Cab FOPS Guard AT390802 $2,584.00 FOPS Level II, ISO 10262 Certified Hydraulic Couplers: Hydraulic Quick Coupler AT343229 $7,835.00 Installation Charge for Hydraulic Coupler AT345608 $1,360.00 Installation Charge Order also requires attachment part number, SHIP-TO address for Paladin Custom Works, AND reference related machine order number.
Page 7 of 9 3/31/2015 The related machine order must reference the attachment order number. Order code available only for Kernersville, North Carolina installations. Hydraulic Thumb Kits: Please click on the following link to access the freight rate tables. Deere/Hitachi Hydraulic Thumb Installation AT339844 $1,928.00 Labor for installation of Deere/Hitachi thumb at Paladin Customworks Kernersville, NC. Hydraulic Thumb Kit, Direct AT379644 $8,300.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulic Thumb Kit, Direct for Couplers AT379645 $8,300.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulic Thumb Kit, Progressive AT379646 $10,325.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulic Thumb Kit, Progressive for Couplers AT379647 $10,325.00 Teeth matching between the bucket and thumb will depend on the bucket width, number of teeth, and tooth spacing. Please see DMAC solution 94331 for optimum thumb and bucket teeth engagement. Hydraulics: Auxiliary High Flow Lines for 3.1 M Arm AT448519 $4,493.00 For S2 engines only. Auxiliary Hydraulic Lines for 2.6 M Arm AT415229 $4,374.00 Auxiliary Hydraulic Lines for 2.6 M Arm AT448517 $4,374.00 For S2 engines only. Auxiliary Hydraulic Lines for 3.1 M Arm AT415230 $4,493.00 Auxiliary Hydraulics, Attachment Combination Kit AT343990 $577.00 Requires Auxiliary High-Flow Hydraulic Lines. Allows for a combination of attachments (i.e. hammer and thumb) to be connected to the high-flow lines, ready for operation. Kit includes parts to replace the arm tube of the high-flow hydraulic lines with a short tube and uses the existing stop valves to shut-off thumb operation when not in use. Control Handle for Auxiliary Hydraulics, Left-Hand AT327652 $515.00
Page 8 of 9 3/31/2015 Requires right-hand control handle for auxiliary hydraulics, AT390774, on the 450-850 size excavators. Requires control solenoid for either 1-way or 2-way auxiliary hydraulics. Recommended for use with auxiliary hydraulic lines. Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch AT390742 $931.00 Does not use the monitor for flow control. Does not require solenoids for auxiliary hydraulics. Includes foot switch, solenoid, relays, wiring, and hoses. Control Solenoid for 1-way Auxiliary Hydraulics with Foot Switch AT446154 $931.00 Does not use the monitor for flow control. Does not require solenoids for auxiliary hydraulics. Includes foot switch, solenoid, relays, wiring, and hoses. Control Solenoids for 2-Way Auxiliary Hydraulics AT390718 $784.00 Monitor can be used to control hydraulic flow. Can be used with either right-hand or left-hand control handle. Control Solenoids for 2-Way Auxiliary Hydraulics AT445459 $784.00 Monitor can be used to control hydraulic flow. Can be used with either right-hand or left-hand control handle. Foot Control, Two-Way Hydraulics AT390739 $1,970.00 Hydraulic Filter Restriction Indicator Kit AT334168 $774.00 Mechanical Control Pattern Selector Kit ETN93716 $987.00 Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control pattern. Some excavators require additional parts. Mechanical Control Pattern Selector Kit AT448521 $987.00 For S2 engines only. Provides ability to switch control pattern between ISO/SAE Excavator and Deere Backhoe control pattern. Some excavators require additional parts. Single Pedal Propel Kit AT390776 $2,080.00 Operator Environment: Guard, Lower Front Window ISO Level II AT390824 $1,048.00 Guard, Upper Front Window ISO Level II AT390823 $788.00 MP3 Player Field Kit ETN93549 $160.00 Work Lights AT396663 $726.00 Additional 2 Cab lights, with 1 Right hand Boom Light. Overall Vehicle: Rear View Camera AT422263 $1,679.00 Vandal Cover Kit AT390721 $2,208.00