Page Title Exterior Folding Door Systems F3 Bottom Rolling Folding Door Hardware System Thermally Broken Aluminum Frame & Weathersealing for Exterior Folding Doors & Windows OUTSWING APPLICATION ONLY www.thedsgroup.com Tomorrow s Innovative Solutions for Today s Doors & Windows The DS Group Of Companies: Draftseal, Kristrack, Eclipse Architectural & DSD Hardware Eclipse F3 Bottom Rolling System Revision (5) March 2, 2016 This catalogue may not be up to date. Always refer to website for most up to date content.
F3 Bottom Rolling Folding Door Hardware F3 Aluminum Frame (Thermally Broken) & Weathersealing for Exterior Folding Doors & Windows (outswing only) Size and Weight Parameters: maximum panel weight: 176 lbs (80 kg) each panel maximum panel width: 36 (914mm) maximum panel height: 96 (2438mm) panel thickness: 1-3/4 (44.45 mm) only maximum number of panels: 8 each direction Note: When using maximum panel width & height 36 x 96 (914mm x 2438mm) panel may exceed maximum panel weight of 176 lbs (80 kg). Calculated weight check should be done. Parts Selection Eclipse F3 is specified with 4 separate groups: / Aluminum Frame (Thermally Broken) Sill, Jambs & Header / Weathersealing / Flushbolts / Hardware / Components are required from all 4 groups to build an Eclipse F3 folding door system. F3 Aluminum Frame System (Thermally Broken) Available in 2 finishes: bronze or white powder coat T.B. T.B. T.B. Folding Door Hardware Available in: pvd bronze over 304 stainless steel brushed stainless steel (304SS) F3 Sill Bottom track for rollers & F.B. channel ECF3SILLTB F3 Jamb ECF3JAMBTB F3 Header Top channel / Guide & F.B. channel ECF3HEADTB Weatherseals & Astragal DS434 Weatherseal for sill, jamb and header. Black, brown or white DS416 Weatherseal for between doors. Black, brown or white DS369A7145BL Aluminum T-slot extrusion with black pile insert, for bottom of doors DS415BL Black DS415W White weatherseal for between doors, use on clad doors where kerf slot is not possible KT190 Fir astragal, may be stained or painted DS434 Kerf seal DSP108-35BL Pile weatherseal for door with astragal, 5/16 (8mm) pile height, black DS7145-270BL Pile weatherseal for KT70 & KT75 top track, black 2 Options Available Flushbolts (outswing doors) or 8 (200mm) or 16 (400mm) or 24 (600mm) or 39 (1000mm) Twinpoint Locking SERIES-DBOT (pin is offset). 1 (25.4mm) throw length Available in 2 finishes: bronze powder coat & brushed metallic to match stainless steel 2 finishes available for cover plate: brushed metallic aluminum & black anodized 5 finishes available for swing handle: black powder coat (cast aluminum handle) grey powder coat (cast aluminum handle) bronze powder coat (cast aluminum handle) pvd bronze over stainless steel and brushed stainless steel 304 SS Eclipse Warranty The Eclipse program is a complete product offering. Component deletions and/or substitutions are strictly prohibited. Warranty is void if system has missing or substitute products. Please refer to www.thedsgroup.com/terms for our full warranty information, terms & conditions, returns & allowances, claims policy, and other general information. 2 ALL DRAWINGS NO SCALE Copyright 2016 DS Group & Eclipse Architectural
INDEX WEIGHT & SIZING SPECS 2 WEATHERSEALS & ASTRAGALS 2 ECLIPSE WARRANTY INFO 2 F3 ARCHITECTURAL DETAIL 4-5 F3 CONFIGURATIONS 6-7 F3 FRAME PROFILES 8 LOCKING OPTIONS 9 LT2 TWINPOINT LOCK 10-15 DBOT FLUSHBOLTS 16 FLUSHBOLT SIZING 17 MAGNETS, DOOR HOLD 17 KT190C WOOD ASTRAGAL 17 SURELOCK ADJUSTMENT 19 DOOR SIZE CALCULATOR 20 COMPONENT SELECTION 21 HARDWARE SELECTION 22-23 Bottom-Rolling Technology Eliminates The Need For Strong Upper Beams Bottom rolling elimiates the need for restricting upper beans Eclipse F3 allows for the cost-effective remodel or retrofit of any opening that previously had a sliding door. Now everyone can enjoy the benefits of folding doors, combining the pleasures of a seamless indoor/outdoor lifestyle with fingertip operation. Folding doors provide vistas, natural light, fresh air and larger living space particularly when entertaining, and unlike sliding doors, require no fixed glass panels or posts. F3 is based on simple but sophisticated technology using a range of strategically placed bearings to allow the bottom of the door to carry the weight, while remaining easy to manoeuvre. Unlike other bottom-rolling systems, Centor controlled windows and doors glide through tracks, not rails, with movement controlled by articulated carriers, appropriately-sized wheels and side thrust bearings. With Eclipse s new bottom-rolling technology, quality folding doors and windows are within reach of every existing building and to every door and window manufacturer. The patented system installs with simple hand and power tools and requires no structural changes to the building. Bottom-Rolling Freedom The new F3 Bottom-Rolling System for folding doors is the industry s first comprehensive bottom-rolling hardware technology, putting folding doors and windows into any existing building space without major structural changes. Bottom-rolling systems allow the weight of the door to be transferred away from the top of the opening, eliminating the need for a strong and often restricting upper beam freeing up more design space. Copyright 2016 DS Group & Eclipse Architectural 3
F3 Architectural Detail F3 Hardware Placement (4L) top pivot end guide half offset hinge intermediate guide wall pivot half offset hinge with handle intermediate carrier bottom pivot end carrier F3 Top View 5/32 (4mm) panel to panel gap 5/32 (4mm) panel to panel gap jamb clearance 9/32 (7mm) 5/32 (4mm) panel to panel gap jamb clearance 9/32 (7mm) F3 Exterior Face View 7/32 (5mm) min head clearance 13/32 (10mm) min sill clearance 4 ALL DRAWINGS NO SCALE Copyright 2016 DS Group & Eclipse Architectural
F3 Architectural Detail F3 Top View panel thickness 16 15 hinge offset panel width F3 Cross Section 1-1/4 (31mm) 4-17/32 (115mm) min 3/16 (5mm) 19/32 (15mm) 2-3/8 (60mm) 2-9/32 (58mm) PLEASE NOTE: When using DBOT Series Flushbolt, top of panel to top of hinge measurement is 2-3/8 (60mm). When using Twinpoint Series Flushbolt assembly, top of panel to top of hinge measurement is 5-29/32 (150mm). 5/16 (8mm) to face door 1-3/4 (45mm) to face door 7/8 (22mm) min 13/32 (10mm) 34 2-3/8 (60mm) 2-1/2 (64mm) PLEASE NOTE: When using DBOT Series Flushbolt, bottom of panel to bottom of hinge measurement is 2-3/8 (60mm). When using Twinpoint Series Flushbolt assembly, bottom of panel to bottom of hinge measurement is 5-29/32 (150mm). Copyright 2016 DS Group & Eclipse Architectural ALL DRAWINGS NO SCALE 5
F3 Configurations - Outswing Application Only CODE OPENING CONFIGURATION HARDWARE 2L 2L1R 3L 3L1R 4L 4L1R 3L2R 5L 3L3R RCS RCS This configuration not accessible from exterior RCS RCS LCS may be reversed This configuration not accessible from exterior 1 x pivot set 1 x wall pivot set* 1 x right carrier set 1 x hinge set 2 x flushbolt or 1 x twinpoint lock 1 x right carrier set 1 x hinge set 2 x flushbolt or 1 x twinpoint lock 1 x pivot set 1 x wall pivot set* 1 x intermediate carrier set 1 x half offset hinge set 2 x flushbolt or 1 x twinpoint lock 1 x intermediate carrier set 1 x half offset hinge set 4 x flushbolt 1 x pivot set 1 x wall pivot set* 1 x intermediate carrier set 1 x right carrier set 2 x half offset hinge set 4 x flushbolt or 2 x twinpoint lock 1 x intermediate carrier set 1 x right carrier set 2 x half offset hinge set 4 x flushbolt or 2 x twinpoint lock 1 x intermediate carrier set 1 x left carrier set 1 x hinge set 1 x half offset hinge set 4 x flushbolt or 2 x twinpoint lock 1 x pivot set 1 x wall pivot set* 2 x intermediate carrier set 1 x hinge set 1 x half offset hinge set 4 x flushbolt or 2 x twinpoint lock 2 x intermediate carrier set 2 x half offset hinge set 6 x flushbolt Common panel layouts Hardware legend PS pivot set WPS wall pivot set intermediate carrier set LCS left carrier set RCS right carrier set half offset hinge set hinge set (flat) EH external handle DB flushbolt TL twinpoint lock IP internal pull handle Legend passage set handles / lock sets flushbolts top & bottom or twinpoint lock NOTE: wall pivot set required for doors over 7 4 (2250mm) in height. 7L 4L3R 5L2R RCS LCS 1 x pivot set 3 x intermediate carrier set 2 x hinge set 1 x half offset hinge set 6 x flushbolt or 3 x twinpoint lock 2 x intermediate carrier set 1 x right carrier set 3 x half offset hinge set 6 x flushbolt or 3 x twinpoint lock 2 x intermediate carrier set 1 x left carrier set 2 x hinge set 1 x half offset hinge set 6 x flushbolt or 3 x twinpoint lock Floating door pairs LCS DB RCS Per pair of doors: 1 x left carrier set 1 x right carrier set 1 x hinge set 2 x flushbolt 5L3R 3 x intermediate carrier set 1 x hinge set 2 x half offset hinge set 8 x flushbolt 6 ALL DRAWINGS NO SCALE Copyright 2016 DS Group & Eclipse Architectural
F3 Configurations - Outswing Application Only CODE OPENING CONFIGURATION HARDWARE 2R 1L2R 3R 1L3R 2L2R 1L4R 4R 2L3R 5R 3L4R 7R 2L5R 8R LCS LCS RCS RCS RCS LCS PS, WPS LCS LCS LCS This configuration not accessible from exterior This configuration not accessible from exterior LCS This configuration not accessible from exterior 1 x pivot set 1 x wall pivot set* 1 x left carrier set 1 x hinge set 2 x flushbolt or 1 x twinpoint lock 1 x left carrier set 1 x hinge set 2 x flushbolt or 1 x twinpoint lock 1 x pivot set 1 x wall pivot set* 1 x intermediate carrier set 1 x half offset hinge set 2 x flushbolt or 1 x twinpoint lock 1 x intermediate carrier set 1 x half offset hinge set 4 x flushbolt 1 x right carrier set 1 x left carrier set 2 x hinge set 4 x flushbolt or 2 x twinpoint lock 1 x intermediate carrier set 1 x left carrier set 2 x half offset hinge set 4 x flushbolt or 2 x twinpoint lock 1 x pivot set 1 x wall pivot set* 1 x intermediate carrier set 1 x left carrier set 2 x half offset hinge set 4 x flushbolt or 2 x twinpoint lock 1 x intermediate carrier set 1 x right carrier set 1 x hinge set 1 x half offset hinge set 4 x flushbolt or 2 x twinpoint lock 1 x pivot set 1 x wall pivot set* 2 x intermediate carrier set 1 x hinge set 1 x half offset hinge set 4 x flushbolt or 2 x twinpoint lock 2 x intermediate carrier set 1 x left carrier set 3 x half offset hinge set 6 x flushbolt or 3 x twinpoint lock 1 x pivot set 1 x wall pivot set* 3 x intermediate carrier set 2 x hinge set 1 x half offset hinge set 6 x flushbolt or 3 x twinpoint lock 2 x intermediate carrier set 1 x right carrier set 2 x hinge set 1 x half offset hinge set 6 x flushbolt or 3 x twinpoint lock 1 x pivot set 1 x wall pivot set* 3 x intermediate carrier set 1 x left carrier set 2 x hinge set 2 x half offset hinge set 8 x flushbolt or 4 x twinpoint lock Hardware application (3L2R) pivot set jamb door DB or TL intermediate carrier & guide set basic door service door leading door half offset hinge set left carrier & guide set passage set handles/lock sets flat hinge set Outswing application, internal handle option interior exterior DF1PH pivot set jamb door DB or TL Use one internal pull handle on exit door (outward system) where passage set / lock not required. Use flushbolts top and bottom to lock door from the inside only. NOTE: Exit door not accessible from exterior in this application. Wall pivot set required for doors over 7 4 (2250mm) in height. Copyright 2016 DS Group & Eclipse Architectural ALL DRAWINGS NO SCALE 7
F3 Aluminum Frame Bottom Rolling (Thermally Broken) F3 Header Top channel guide / plus flushbolt channel 1-1/4 (32mm) F3 PVC Channel for Header 2-9/32 (58mm) Top guide channel Flushbolt channel for DBOT Series flushbolt or LT2 Twinpoint Lock. Weatherseal not included with header. Order separately. 4-9/16 (116mm) F3 Jamb Weatherseal not included with jamb. Order separately. 2-5/32 (55mm) 1-1/4 (32mm) 4-9/16 (116mm) F3 Sill Rubber sill cover and weatherseal not included. Order separately. Weatherseal not included with sill. Order separately. flush bolt channel 2-9/32 (58mm) 1-3/8 (35mm) 1-1/4 (32mm) bottom track for rollers F3 Rubber Insert for Sill 4-9/16 (116mm) 8 FULL SCALE EXCEPT AS NOTED Copyright 2016 DS Group & Eclipse Architectural
Locking Options for Selected Configurations A ACTIVE PANEL: DSD MK2 Multipoint lock & lever lock set ADJOINING PANEL: KTDBOT Series flushbolt (top & bottom) Surface mount astragal (KT190C) KTDBOT flushbolt INTERIOR Locking Options For Selected Configurations (applies to A, B, C & D) 3L1R 1L3R ACTIVE PANEL 1-3/4 (44.45mm) ADJOINING PANEL 3L3R 4-7/8 (124mm) EXTERIOR 5L1R B 4-7/8 (124mm) ACTIVE PANEL: DSD MK2 Multipoint lock & lever lock set ADJOINING PANEL: KTDBOT Series flushbolt (top & bottom) In between panel astragal (DS198) KTDBOT flushbolt INTERIOR 1L5R 1L7R 7L1R ACTIVE PANEL 1-3/4 (44.45mm) ADJOINING PANEL 4-7/8 (124mm) EXTERIOR 5L3R 4-7/8 (124mm) 3L5R C ACTIVE PANEL: DSD MK2 Multipoint lock & lever lock set ADJOINING PANEL: DSD MK2 Multipoint lock (shoot bolts top & bottom) & lever lock set In between panel astragal (DS198) INTERIOR ACTIVE PANEL 1-3/4 (44.45mm) ADJOINING PANEL EXTERIOR 4-7/8 (124mm) 4-7/8 (124mm) D ACTIVE PANEL: DSD MK2 Multipoint lock & lever lock set ADJOINING PANEL: LT2 Model Twinpoint Lock (shoot bolts top & bottom) In between panel astragal (by other) LT2 Twinpoint INTERIOR ACTIVE PANEL 1-13/16 (46mm) ADJOINING PANEL 4-7/8 (124mm) EXTERIOR 4-7/8 (124mm) Copyright 2016 DS Group & Eclipse Architectural HALF SCALE EXCEPT AS NOTED 9
F3 Sill with Two Locking OptionsFor 1-3/4 (44.5mm) Door Thickness Only TWINPOINT FLUSHBOLT F3 Top Track / Header F3 Top Track / Header Twinpoint DBOT Series Flushbolt F3 Sill F3 Sill NO SCALE NO SCALE The new DBOT flushbolt & Twinpoint lock were designed to utilize the same channel in our F3 sill, thus giving you the option to now offer your customer the original flushbolt design or the simple hand rotation of the single handle, driving a 1 throw into the head and sill. Eclipse Twinpoint Lock & Swing Handle Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel. 4L twinpoint & swing handle twinpoint & swing handle twinpoint & swing handle 3L multipoint & lever lock set Specifications Minimum door thickness: 1-3/8 (35 mm) Throw length: 1 (25 mm) Uses: folding, french & sliding Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel. Function The LT2 operates easily with a simple handle rotation, driving a 1 (25mm) throw into the head and sill. This makes it one of the most secure bolt locks on the market. An installed Twinpoint system is completely accessible and serviceable. For people with mobility impairments, the Twinpoint offers the security of two flushbolts, but without the access problems associated with flushbolts being too high or low to reach, and hard-to-grip door handles. Style LT2 has the sleek and clean styling synonymous with all Eclipse products. Their low profile allows any folding system, such as F3, E2, E3 or E4 to stack neatly, without intrusive door furniture getting in the way. Eclipse Twinpoint locks are fully concealed within the door stile, avoiding long or hardto-reach dropbolts fixed to the door face, particularly on tall doors. The Eclipse Twinpoint is an unobtrusive, functional and sleek locking solution. Testing The Centor LT2 has been tested to 100,000 cycles at maximum configuration to ensure smooth working order beyond their 10 year warranty period. The LT2 Twinpoint locking system has also been exposed to dust, mud, sand and corrosive atmospheres to ensure they stand up to real life use. This includes exposure to salt spray for seaside installations. 10 ALL DRAWINGS NO SCALE Copyright 2016 DS Group & Eclipse Architectural
LT2 TwinPoint Lock & DF3 (Aluminum) or DF4 (Stainless Steel) Swing Handles Kit Components For Twinpoint Assembly transmission rod two finishes available on outer housing cover plate lock/gear box swing handle assembly (6 finishes) transmission rod PLEASE NOTE: When ordering complete TwinPoint Assembly, you are required to order: transmission rod & cover plate, lock/gear box, swing handle & cups. Twinpoint Lock assembly not available in PVD Brass (TG) PRODUCT # EC TwinPoint Lock (LT2 Model) for use with DF3 (Aluminum) & DF4 (Stainless Steel) Models ECLT2TRSN0924X TwinPoint transmission rod, cover plate and strike plate for 96 (2438mm) door height / brushed metallic aluminum finish ECLT2TRSN0924Y TwinPoint transmission rod, cover plate and strike plate for 96 (2438mm) door height / black anodized finish ECLT2TRSN0930X TwinPoint transmission rod, cover plate and strike plate for 120 (3048mm) door height / brushed metallic aluminum finish ECLT2TRSN0930Y TwinPoint transmission rod, cover plate and strike plate for 120 (3048mm) door height / black anodized finish EC Lock Gear Box for EC TwinPoint (LT2 Model) ECLT2NS Lock/gear box for EC TwinPoint transmission rod, cover plate & handle EC Swing Handle DF3 (Aluminum) Model For EC TwinPoint (LT2 Model) ECDF3SHNAL DF3 swing handle aluminum, black powder coat ECDF3SHNAPCN DF3 swing handle aluminum, satin aluminum powder coat ECDF3SHNAQ DF3 swing handle aluminum, bronze powder coat EC Swing Handle DF4 (Stainless Steel) Model For EC TwinPoint (LT2 Model) ECDF4SHNSOL DF4 swing handle stainless steel, PVD bronze finish ECDF4SHNSS DF4 swing handle stainless steel, brushed finish Cup for Sill or Head (Mandatory for Sill, Optional for Head) ECLTBC8SS Brushed S.S. Finish ECLTBC8SOL PVD Bronze Finish TL2 Router Bit ECLT2RB Router bit for LT2 TwinPoint Lock Assembly Eclipse E3 Drilling Jig for E3 Hinge placement on door KTE3DJ Eclipse E3 drilling jig for wood doors Strike Plate for Head (For replacement purposes only) One strike supplied with Twinpoint (Standard) ECLTSP8SS Brushed S.S. Finish ECLTSP8OL PVD Bronze Finish Copyright 2016 DS Group & Eclipse Architectural ALL DRAWINGS NO SCALE 11
Twinpoint Lock Shown With 1-3/4 Panel 4-9/16 (115.8mm) F3 Top Track / Header DBOT Flusbolt Shown With 1-3/4 Panel F3 Top Track / Header 4-9/16 (115.8mm) 4-23/32 (120mm) 5-29/32 (150mm) 2-3/8 (60 mm) 3/8 (9.4mm) hinge placement is higher on door than shown DF3 Model TwinPoint Swing Handle (Cast Aluminum) 4 finishes available or DF4 Model Twinpoint Swing Handle (Stainless Steel) 2 finishes available 36 (914mm) hinge placement is lower on door than shown 36 (914mm) 5-29/32 (150mm) 5/32 (4mm) 2-3/8 (60mm) 3/8 (9.4mm) 3/8 (9.4mm) 13/32 (10mm) 13/32 (10mm) 2-9/32 (58mm) F3 Sill used in conjunction with Twinpoint F3 Sill used in conjunction with DBOT Flushbolt Series 4-9/16 (115.9mm) 4-9/16 (115.9mm) 12 ALL DRAWINGS NO SCALE Copyright 2016 DS Group & Eclipse Architectural
Wood Stile Route Profile (Outswing Application) For LT2 Model 1/2 (12.7mm) 5/32 (4mm) 1-3/32 (27.80mm) Detail A 3/32 (2.5mm) 9/16 (14.4mm) Detail A 60.0 5/64 (1.8mm) 2-1/8 (54mm) 9/32 (7.1mm) 32/23 (18.4mm) ECLT2RB Route stile 1-3/4 (44.5mm) min 1-3/8 (35mm) A 1-1/32 (26mm) Back Set 1-7/64 (28mm) R7 9/32 (7.2mm) 11/16 (18mm) 15/32 (12mm) B R 1/2 (12.7mm) 4-61/64 (126mm) 3-3/16 (81mm) 14-11/64 (360mm) 9-1/16 (230.2mm) 2-5/64 (53mm) 13/64 (5mm) standard height 9/14 (36mm) A Copyright 2016 DS Group & Eclipse Architectural ALL DRAWINGS NO SCALE 13
F3 Hinge Placement Over TwinPoint 11/64 (4.2mm) 21/64 (8.4mm) 5/32" (4mm) 1-3/32" (27.8mm) E2 Hinge 9/16" (14.4mm) 1-3/4" (44.5mm) A A 1-3/4 (44.5mm) SECTION A-A E3 hinge R 13/32 (10.5mm) 19/64 (7.6mm) 1-11/16 (43mm) 13/16 (21mm) 2-13/32 (61mm) Strike plate for head ECLTSP8SS Brushed s.s. finish ECLTSP8OL PVD bronze finish Flushbolt metal cup used with floor channel ECLTBC8SS Brushed s.s. finish ECLTBC8SOL PVD bronze finish 14 ALL DRAWINGS NO SCALE Copyright 2016 DS Group & Eclipse Architectural
DF3 TwinPoint Swing Handle, Choice of 4 Finishes Over Cast Aluminum White Powder Coat Satin Aluminum Powder Coat Black Powder Coat Bronze Powder Coat LT2 TwinPoint Housing Cover Plate Finishes DF4 Twinpoint Swing Handle (SS) Choice of 2 Finishes Brushed Metallic Aluminum Black Anodized Aluminum Brushed stainless steel PLEASE NOTE: For technical reasons associated with color reproduction, the colors shown on this brochure give only an indication of color & finish. No warranty or guarantee can be given that they will exactly match the product as supplied. PVD bronze over stainless steel Finishes & Materials The Twinpoint door furniture is available in a range of finishes to suit any door or décor. Twinpoint Lock assembly not available in PVD Brass (TG) LT2 Model Twinpoint Swing Handle DF3: Aluminum handle (4 finishes) DF4: Stainless Steel Handle (2 finishes) LT2 Transmission Housing Brushed Metallic Aluminum or Black Anodized finish Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel. 4L twinpoint & swing handle twinpoint & swing handle 3L twinpoint & swing handle multipoint & lever lock set Copyright 2016 DS Group & Eclipse Architectural ALL DRAWINGS NO SCALE 15
Flushbolts For E3 Eclipse Outswing Folding Doors: DBOT Series SPECIFICATIONS Max wind load: 450kg (990lb) force Min door thickness: 1-3/4 (44.5mm) Throw length: 1 (25mm) Finishes: Bronze powder coat on aluminum to match pvd bronze finish on E3 hinges. Brushed metallic on aluminum to match stainless steel finish on E3 hinges. Bright gold (G) finish on aluminum to match pvd brass finish on E3 hinges. Bright gold (G) finish is custom order, call for manufacturing time. The flush-mounted flushbolts, rounded style and 1 (25mm) throw are designed for use with sliding and folding doors. This flushbolt will resist high winds and is rated to resist a 250kg load in Western Red Cedar and 450kg in Amoora. The bolts are easily installed with a dedicated router bit and are available in three finishes. Architectural Detail Flushbolt Assembly 1-27/64 (36mm) NEW PRODUCT 43/64 (17mm) 35/64 (14mm) 47/64 (18.6mm) pin diameter 25/64 (10mm) 7-7/8 (200mm) 15-3/4 (400mm) 23-5/8 (600mm) 39-3/8 (1000mm) 1 (25mm) throw length regardless of bolt length 1 (25mm) INTERIOR 7/8 (22mm) 2-7/16 (62mm) 13/16 (20.6mm) KT749 Flushbolt cup used with floor channel and ADA sill 1/8 (2.5mm) 1-27/64 (36mm) CL 9/16 (14mm) flushbolt machining centered at stile width 3/4 (19mm) R = 1/64 (0.5mm) Actual machining for flushbolts (face plate) 1-27/64 x 7-7/8 (36mm x 200mm) 1-27/64 x 23-5/8 (36mm x 600mm) 1-27/64 x 15-3/4 (36mm x 400mm) 1-27/64 x 39-3/8 (36mm x 1000mm) SELECT FINISH PRODUCT NUMBER KTDBOT200NRQ 200mm, 1 throw, round end bronze powder coat KTDBOT400NRQ 400mm, 1 throw, round end finish on aluminum KTDBOT600NRQ 600mm, 1 throw, round end KTDBOT1000NRQ 1000mm, 1 throw, round end KTDBOT200NRX 200mm, 1 throw, round end brushed metallic finish KTDBOT400NRX 400mm, 1 throw, round end on aluminum to match stainless steel KTDBOT600NRX 600mm, 1 throw, round end KTDBOT1000NRX 1000mm, 1 throw, round end KTDBOT200NRG 200mm, 1 throw, round end bright gold finish KTDBOT400NRG 400mm, 1 throw, round end on aluminum KTDBOT600NRG 600mm, 1 throw, round end Bright gold (G) finish is custom order, call for manufacturing time. Flushbolt cup used with floor channel and ADA sill KT749BRONZE bronze powder coat KT749DCH Satin chrome KTE2DBFORB Router bit for flushbolts (dedicated router bits are available) Strike plate for header KTDBSPQ bronze powder coat KTDBSPS Satin chrome PLEASE NOTE: Flushbolt housing & slide bar are manufactured from aluminum components 16 ALL DRAWINGS NO SCALE Copyright 2016 DS Group & Eclipse Architectural
F3 Flushbolt Sizing Suggested flushbolt lengths for door heights 80 to 96 (2.032m to 2438m) NOTE: End user may require longer flushbolts for top of doors for easier reach. 8 (200mm) flushbolt 16 (400mm) flushbolt NO SCALE Magnets KTEMAG Magnets for holding the door panels in the open position 3L 2-3/8 (60.3mm) 13/16 (20.6mm) KTEMAG (sold as pairs) NO SCALE up to 84 (2134mm) 84-1/16 to 96 (2159mm to 2438mm) 8 (200mm) flushbolt 8 (200mm) flushbolt KT190C Wood Astragal 1-5/16 (33.34mm) I.E. 5L magnets door hold 1-1/8 (28.5mm) kerf slot 1/8 x 3/8 (3.18mm x 9.5mm) Latching door hold (DH) INTERIOR 9/32 (7.14mm) 1-3/4 (44.5mm) door 1/8 (3.23mm) 3/8 (9.5mm) DS434 inserted weatherseal, brown, white or black DSP108 35BL Kerf inserted fin pile NO SCALE 9/32 (7.14mm) 1/8 (3.23mm) KT740DHC Clear anodized KT740DHD Bronze anodized 5/16 (7.94mm) Magnet Door Hold NO SCALE T-Unit NO SCALE set screen adjustment screw KTDCAS satin aluminum finish KTDCAOL black finish main unit Copyright 2016 DS Group & Eclipse Architectural FULL SCALE EXCEPT AS NOTED 17
Fully Adjustable, Compensating For Less Than Perfect Openings Design Features Openings fitted with controlled folding windows and doors include protective features not available with other systems. These include: the original weathersealing technology floating rollers allow for smooth action even with sill bow or twist sill covers to avoid dirt collecting in the tracks guards which work like a snow plough to remove any debris tapered rollers and sloping track facilitate debris removal drainage holes to flush away water and dust F3 Up Close Even a casual glance at the F3 system gives a strong impression of Eclipse s commitment to quality, but it s only upon closer inspection that the attention to detail really becomes apparent. Stacked with standard features and with an abundance of options to choose from, Centor F3 looks even better up close. Materials And Finishes F3 carriers, guides, pivots and hinges are available in brushed stainless steel, PVD brass or PVD bronze finish over stainless steel. Head tracks are produced in extruded aluminum. Panel Size And Materials Our innovative hinge system enables the use of uniform width door panels regardless of the door configuration, ensuring maximum efficiency in door manufacture. Easily installed hardware can be teamed with door panels in wood, aluminum, PVC or fiberglass. Adjustment F3 folding doors can be adjusted both vertically and horizontally. Once door heights are set and locked, the mechanism will not self adjust or loosen over time, meaning doors will not drop. Further adjustments can be made at any time with a screwdriver. Rain and Wind Doors using the Eclipse E3 and E4 systems have been certified to stringent Miami-Dade County hurricane standards, the toughest testing anywhere in the world. With similar technology built into F3, impressive water performance ratings are achievable on outward opening doors. Driving rain and howling gales can be shut out. Air Infiltration The F3 system achieves its superior rain and wind resistance in part from the way it allows the folding doors to close snugly against weatherseals. In the same way, doors using F3 effectively resist air infiltration to a level up to 50 times better than a sliding door. All individual F3 components have been extensively laboratory tested, ensuring years of trouble-free use from hardware which ages with grace. Cyclic Testing F3 has undergone Eclipse s minimum requirement of cyclic testing to a grueling 50,000 cycles without failure at maximum configuration, however many individual components are rated to over 100,000 cycles. Testing Stainless steel, PVD brass, anodized aluminum and engineering grade plastics are used throughout the F3 system with all materials carefully selected to maximise performance in any environment. Regular corrosion testing has been performed in salt spray chamber, fixing hardware to various substrates to ensure that F3 will perform admirably. Finite Element Analysis Finite Element Analysis (FEA) is a computerised simulation technique where products are exposed to virtual operating environments and accurate predictions made in terms of load and deflection. FEA is executed in the design process to ensure the best balance of performance, cost and materials in every system. 18 ALL DRAWINGS NO SCALE Copyright 2016 DS Group & Eclipse Architectural
Solves Challenges Previously Associated With Bottom-Rolling F3 Assurance Delivering life-long durability and fingertip operation, the F3 s breakthrough technology and comprehensive feature set solves the many challenges previously associated with bottom-rolling hardware systems. Unparalleled Security The new slimmer frames fit unobtrusively beneath glazed panels with fixed and irremovable adjustment pins providing maximum strength and security. Specifying F3 For detailed component selection, including calculating size and number of door panels, specifiers can use Doorcalc. Architects and designers can feel comfortable simply specifying Eclipse F3 and leave detailed component selection to the builder, joiner or fabricator. Warranty Centor F3 bottom-rolling folding doors and windows can continue to open and close as new, long past their 10 year guarantee. Surelock 3 Adjustment Surelock 3 is a patented carrier pin locking system which ensures that once door heights are set at the top pivots, intermediate and end carriers, they stay set! Using Surelock 3 is simple 1 Insert a flat-bladed screwdriver into slot to depress the spring. 2 With the spring depressed start the adjustment using a 9/16 (14mm) spanner. 3 Turn the spanner a full revolution. 4 Repeat as necessary. Every full rotation = 1/16 (1.25mm) height adjustment Copyright 2016 DS Group & Eclipse Architectural ALL DRAWINGS NO SCALE 19
Door Size Calculator To calculate the dimensions of the doors or openings we strongly recommend using Centor s Doorcalc program, which is a Microsoft Excel spreadsheet. To manually calculate door sizing for an opening, follow these steps: 1. Prepare a basic sketch of your door opening (see worked example), to visualize clearances and check sizes. 2. The calculation is based on all panels being equal width, using half-offset hinges (Patent Pending). Note that the allowance between each panel is 4mm although hinge thickness is less this allowance has been determined by consultation with fabricators as the best approximation for calculation. Clearance between hinges and hinge pins, coupled with the pressure from compression seals accounts for the allowance being larger than the nominal hinge flap thickness. 3. Recommended clearances are as follows: Jamb to panel (door closed) JP 9/32 (7mm) Panel to panel (door closed) PP 5/32 (4mm) Top of panel to head 13/32 (10mm) Bottom of panel to sill 13/32 (10mm) 4. Panel width W Opening width L (Inside jamb to jamb) Total number of panels N Panel width is: W = L 2 x JP (PP x (N 1)) ** N Worked Examples Clear opening size 7 11 1/2 high x 13 9 11/32 wide (L), and a 3L x 2R arrangement. W = 13 9 11/32 2 (9/32 ) (5/32 x (5 1)) W = 2 8 27/32 5 Check against your door layout: L = 2 (9/32 ) + 4 (5/32 ) + 5 (2 8 27/32 ) = 13 9 11/32 (OK) The panel height is the opening height less the nominal top and bottom clearances: Panel Height H = 7 11 1/2 13/32 13/32 = 7 10 7/8 ** NOTE: for even sets, IE: 2L2R, 4L2R, 2L4R, 2L6R, 6L2R, 4L, 4L4R, 4R, 8L or 8R, the meeting gap is larger double seals are used to close the gap. If tighter gap between panels is preferred, then hinge flaps of left hand or right hand carriers can be mortised in. W = L 2 x JP (PP x N) N 20 FULL SCALE EXCEPT AS NOTED Copyright 2016 DS Group & Eclipse Architectural
Component Selection Header - Aluminum Thermally Broken (TB) CATALOGUE # ECF3HEADTB9B F3 head extruded aluminum, TB, bronze powder coat, 111 (2819mm) ECF3HEADTB12B F3 head extruded aluminum, TB, bronze powder coat, 146 (3708mm) ECF3HEADTB18B F3 head extruded aluminum, TB, bronze powder coat, 222 (5638mm) ECF3HEADTB9W F3 head extruded aluminum, TB, white powder coat, 111 (2819mm) ECF3HEADTB12W F3 head extruded aluminum, TB, white powder coat, 146 (3708mm) ECF3HEADTB18W F3 head extruded aluminum, TB, white powder coat, 222 (5638mm) Poly Channel (PVC) for Header Guide Channel CATALOGUE # ECF3TOPCH9BL PVC channel insert for F3 head guide channel, black, 111 (2819mm) ECF3TOPCH12BL PVC channel insert for F3 head guide channel, black, 147 (3784mm) ECF3TOPCH18BL PVC channel insert for F3 head guide channel, black, 224 (5699mm) Sill - Aluminum Thermally Broken (TB) CATALOGUE # ECF3SILLTB9B ECF3SILLTB12B ECF3SILLTB18B ECF3SILLTB9W ECF3SILLTB12W ECF3SILLTB18W F3 sill extruded aluminum, TB, bronze powder coat, 111 (2819mm) F3 sill extruded aluminum, TB, bronze powder coat, 146 (3708mm) F3 sill extruded aluminum, TB, bronze powder coat, 222 (5638mm) F3 sill extruded aluminum, TB, white powder coat, 111 (2819mm) F3 sill extruded aluminum, TB, white powder coat, 146 (3708mm) F3 sill extruded aluminum, TB, white powder coat, 222 (5638mm) Rubber Flap used for Sill Channel Cover CATALOGUE # ECF3FRBTS Rubber insert cover for F3 sill, black Jamb - Aluminum Thermally Broken (TB) CATALOGUE # ECF3JAMBTB8B F3 jamb extruded aluminum, TB, bronze powder coat, 96 (2438mm) ECF3JAMBTB10B F3 jamb extruded aluminum, TB, bronze powder coat, 120 (3048mm) ECF3JAMBTB8W F3 jamb extruded aluminum, TB, white powder coat, 96 (2438mm) ECF3JAMBTB10W F3 jamb extruded aluminum, TB, white powder coat, 120 (3048mm) Machining CATALOGUE # ie: header ie: sill ECF3KDM9 ECF3KDM12 Machining charge for 9 ft sill and header, 8 ft jambs Machining charge for 12 ft sill and header, 8 ft jambs ECF3KDM18 Machining charge for 18 ft sill and header, 8 ft jambs PLEASE NOTE: 10 ft jambs same cost as 8 ft jambs. NO SCALE NOTE: jambs machined top and bottom (not shown) Copyright 2016 DS Group & Eclipse Architectural FULL SCALE EXCEPT AS NOTED 21
Hardware Selection Pivot Set PARTS ON PANELS PRODUCT # ECF3PSS F3 pivot set (2 pcs) stainless steel ECF3PSOL F3 pivot set (2 pcs) pvd bronze Wall Pivot PARTS ON PANELS PRODUCT # KTE3WPSS F3 wall pivot set (1 pc) stainless steel KTE3WPSOL F3 wall pivot set (1 pc) pvd bronze Right Carrier Set PARTS ON PANELS PRODUCT # ECF3RCSS F3 right hand carrier set (2 pcs) stainless steel ECF3RCSOL F3 right hand carrier set (2 pcs) pvd bronze Left Carrier Set PARTS ON PANELS PRODUCT # ECF3LCSS F3 left hand carrier set (2 pcs) stainless steel ECF3LCSOL F3 left hand carrier set (2 pcs) pvd bronze Intermediate Carrier Set PARTS ON PANELS PRODUCT # ECF3S F3 intermediate carrier set (3 pcs) stainless steel ECF3OL F3 intermediate carrier set (3 pcs) pvd bronze NO SCALE 22 FULL SCALE EXCEPT AS NOTED Copyright 2016 DS Group & Eclipse Architectural
Hardware Selection Half Offset Hinge Set (with handle) PARTS ON PANELS PRODUCT # KTE3S Half offset hinge set with handle (3 pcs) stainless steel KTE3OL Half offset hinge set with handle (3 pcs) pvd bronze Single Hinge Half Offset (no handle) PRODUCT # KTE3HHN Single half offset hinge (1 pc) stainless steel KTE3HHNHOL Single half offset hinge (1 pc) pvd bronze Single Hinge Half Offset (with handle) PRODUCT # KTE3 (1 pc) stainless steel (with handle) KTE3HHOL (1 pc) pvd bronze (with handle) Flat Hinge Set (with handle) PARTS ON PANELS PRODUCT # KTE3S Flat hinge set with handle (3 pcs) stainless steel KTE3OL Flat hinge set with handle (3 pcs) pvd bronze Single Hinge Flat (no handle) PRODUCT # KTE3HN Single straight hinge (1 pc) stainless steel KTE3HNHOL Single straight hinge (1 pc) pvd bronze Single Hinge Flat (with handle) PRODUCT # KTE3 (1 pc) stainless steel (with handle) KTE3HOL (1 pc) pvd bronze (with handle) NO SCALE Copyright 2016 DS Group & Eclipse Architectural FULL SCALE EXCEPT AS NOTED 23
Page Title www.thedsgroup.com Tomorrow s Innovative Solutions for Today s Doors & Windows The DS Group Of Companies: Draftseal, Kristrack, Eclipse Architectural & DSD Hardware Head Office & Manufacturing Centre, Vancouver, Canada 7470 Buller Avenue, Burnaby, B.C. V5J 4S5 Canada Phone: (604) 451-1080 Fax: (604) 451-1140 info@thedsgroup.com Outside Vancouver, B.C., please use our toll free numbers: Phone: 1-888-520-9009 Fax: 1-800-567-2887 Branch Office & Manufacturing Centre, Toronto, Canada Phone head office toll free 1-888-520-9009 for branch address Branch Office & Distribution Centre, Los Angeles, California Phone head office toll free 1-888-520-9009 for branch address Eclipse Architectural Corporate Showrooms Vancouver & Toronto, Canada Los Angeles, California, USA THE DS GROUP IS THE BRAND IMAGE OF A.K. DRAFT SEAL LTD.