Swivel Top Linear-Lift Installation & Operator s Instruction Manual

Swivel Top Linear-Lift Installation & Operator s Instruction Manual Mv7-0 06/0 August 006 MV7F

Chore-Time Warranty Swivel Top Linear-Lift Chore-Time Warranty Chore-Time Equipment ( Chore-Time ) warrants each new Chore-Time product manufactured by it to be free from defects in material or workmanship for one year from and after the date of initial installation by or for the original purchaser. If such a defect is found by the Manufacturer to exist within the one-year period, the Manufacturer will, at its option, (a) repair or replace such product free of charge, F.O.B. the factory of manufacture, or (b) refund to the original purchaser the original purchase price, in lieu of such repair or replacement. Labor costs associated with the replacement or repair of the product are not covered by the Manufacturer. Conditions and Limitations. The product must be installed by and operated in accordance with the instructions published by the Manufacturer or Warranty will be void.. Warranty is void if all components of the Swivel Linear-Lift Unit are not original equipment supplied by the Manufacturer.. This product must be purchased from and installed by an authorized distributor or certified representative thereof or the Warranty will be void.. Malfunctions or failure resulting from misuse, abuse, negligence, alteration, accident, or lack of proper maintenance shall not be considered defects under the Warranty. 5. This Warranty applies only to systems for the care of poultry and livestock. Other applications in industry or commerce are not covered by this Warranty. The Manufacturer shall not be liable for any Consequential or Special Damage which any purchaser may suffer or claim to suffer as a result of any defect in the product. Consequential or Special Damages as used herein include, but are not limited to, lost or damaged products or goods, costs of transportation, lost sales, lost orders, lost income, increased overhead, labor and incidental costs and operational inefficiencies. THIS WARRANTY CONSTITUTES THE MANUFACTURER S ENTIRE AND SOLE WARRANTY AND THIS MANUFACTURER EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, EXPRESS AND IMPLIED WARRANTIES AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSES SOLD AND DESCRIPTION OR QUALITY OF THE PRODUCT FURNISHED HEREUNDER. Chore-Time Distributors are not authorized to modify or extend the terms and conditions of this Warranty in any manner or to offer or grant any other warranties for Chore-Time products in addition to those terms expressly stated above. An officer of CTB, Inc. must authorize any exceptions to this Warranty in writing. The Manufacturer reserves the right to change models and specifications at any time without notice or obligation to improve previous models. Thank You CTB Inc. P.O. Box 000 Milford, Indiana 65-000 U.S.A. Phone (57) 658-0 Fax (877) 70-885 E-Mail: ctb@ctbinc.com Internet: http//www.ctbinc.com Effective: August 006 The employees of Chore-Time Equipment would like to thank your for your recent Chore-Time purchase. If a problem should arise, your Chore-Time distributor can supply the necessary information to help you. MV7F

Contents Topic Page User Chore-Time Warranty................................................ Support Information....................................................... Distributor and Installer Information.......................................... General............................................................. About This Manual................................................... 5 Safety Information................................................... 5 Safety Alert Symbol.......................................................5 Understanding Signal Words................................................5 Follow Safety Instructions..................................................6 Decal Descriptions........................................................6 DANGER: Electrical Hazard............................................6 DANGER: Moving Parts...............................................6 Introduction and Layout Diagrams..................................... 7 Tools Required...........................................................7 Cable/Pulley Combinations.................................................7 Available Sizes and Speed of Operation........................................8 Standard Swivel Top Linear-Lift- (7859-Series) Part Numbers.................8 Chain Drive Swivel Top Linear-Lift- (808-Series) Part Numbers..............8 Potentiometer Kit (8) Part Numbers...................................8 Swivel Top Linear-Lift Installation..................................... 9 Swivel Top Pulley/Sprocket Angle Adjustment..................................9 Bronze Nut Attachment Detail...............................................9 Cable/Chain Routing Systems.............................................. 0 Ceiling Installations...................................................... Mounting Hole Locations............................................. Ceiling Mount Swivel Top Linear-Lift Installation.............................. Two-Side Tunnel Curtain Application........................................ Side Wall Swivel Top Linear-Lift Installation.................................. Side Wall Swivel Top Linear-Lift Installation.................................. Alternative Vent Plug Locations for Various Swivel Top Linear-Lift Mountings....... 5 Oil Recommendation..................................................... 6 Grease Recommendation.................................................. 6 Swivel Top Linear-Lift Stop Switch Adjustment.......................... 7 Wiring Diagram..................................................... 7 Limit Switch and Schematic Diagram for Standard & Chain Models................ 7 Swivel Top Linear-Lift Switch Assemblies................................ 8 Swivel Top Linear-Lift Switch Assembly #7875............................... 8 Optional Pulleys and Accessories....................................... 9 Swivel Top Linear-Lift Drawings and Parts Listings....................... 0 Standard 7859-Series Drawing............................................. 0 Standard, 7859-Series Parts Listing......................................... Chain Drive, 808-Series Drawing.......................................... Chain Drive, 808-Series Parts Listing...................................... C,D C,I C,I C,I C,I I C,I C,I I C,I C,I C,I MV7F * Legend: C = Customer (end user), D = Distributor (sales), I = Installer of equipment

General Swivel Top Linear-Lift General Support Information The Chore-Time Swivel Top Linear-Lift is designed to open curtains or inlet doors. Using this equipment for any other purpose or in a way not within the operating recommendations specified in this manual will void the warranty and may cause personal injury. This manual is designed to provide comprehensive planning, installation, safety, operation, and parts listing information. The Table of Contents provides a convenient overview of the information in this manual. The Table of Contents also specifies which pages contain information for the sales personnel, installer, and consumer (end user). Distributor and Installer Information Please fill in the following information about your Product. Keep this manual in a clean, dry place for future reference. Distributor s Name Distributor s Address Distributor s Phone Date of Purchase Installer s Name Installer s Address Installer s Phone Date of Installation System Specifications MV7F

Swivel Top Linear-Lift About This Manual About This Manual The intent of this manual is to help you in two ways. One is to follow step-by-step in the order of assembly of your product. The other way is for easy reference if you have questions in a particular area. Important! Read ALL instructions carefully before starting construction. Important! Pay particular attention to all SAFETY information. Metric measurements are shown in millimeters and in brackets, unless otherwise specified. " equals inches and ' equals feet in English measurements. Examples: " [5.] ' [ 9] Safety Information Optional equipment contains necessary instructions for assembly or operation. Major changes from the last printing will be listed on the back cover. This Planning Symbol is used in areas where planning needs to take place before construction continues. Very small numbers near an illustration (i.e., 57-8) are identification of the graphic, not a part number. Caution, Warning and Danger Decals have been placed on the equipment to warn of potentially dangerous situations. Care should be taken to keep this information intact and easy to read at all times. Replace missing or damaged safety decals immediately. Using the equipment for purposes other than specified in this manual may cause personal injury and/or damage to the equipment. Safety Alert Symbol This is a safety alert symbol. When you see this symbol on your equipment, be alert to the potential for personal injury. This equipment is designed to be installed and operated as safely as possible...however, hazards do exist. Understanding Signal Words Signal words are used in conjunction with the safety alert symbol to identify the severity of the warning. DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. WARNING indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. CAUTION indicates a hazardous situation which, if not avoided, MAY result in minor or moderate injury. MV7F 5

Safety Information Swivel Top Linear-Lift Safety Information Follow Safety Instructions Carefully read all safety messages in this manual and on your equipment safety signs. Follow recommended precautions and safe operating practices. Keep safety signs in good condition. Replace missing or damaged safety signs. Decal Descriptions DANGER: Electrical Hazard Disconnect electrical power before inspecting or servicing equipment unless maintenance instructions specifically state otherwise. Ground all electrical equipment for safety. All electrical wiring must be done by a qualified electrician in accordance with local and national electric codes. Ground all non-current carrying metal parts to guard against electrical shock. With the exception of motor overload protection, electrical disconnects and over current protection are not supplied with the equipment. DANGER: Moving Parts Disconnect electrical power before working on system, equipment may start automatically. Otherwise personal injury will result. Severe personal injury will result if the equipment is operated without covers properly installed. 6 MV7F

Swivel Top Linear-Lift Introduction and Layout Diagrams Introduction and Layout Diagrams Same Speed The Swivel Top Linear-Lift is designed to open and close Inlet Curtains or Baffle Boards. It may be wired into the ventilation control (i.e. Static Pressure Inlet Control, Chore-Tronics, Super Selector, etc.) Tools Required 5/6" Nut Driver Wire Strippers Drive Ratchet and /" Socket 5 Electrical Wire Wire Cutters 6 /" Allen Wrench Cable/Pulley Combinations (Ratio :) Linear-Lift TM "/Minute 000 lb. max. Load "/Minute 000 lb. max. Load Speed Up (Ratio :) Linear-Lift TM "/Minute 000 lb. max. Load "/Minute 000 lb. max. Load Slow Down (Ratio :) Linear Lift TM "/Minute 000 lb. max. Load 6"/Minute 000 lb. max. Load Figure. Cable/Pulley Combination MV7F 7

Introduction and Layout Diagrams Swivel Top Linear-Lift Available Sizes and Speed of Operation The Swivel Top Linear-Lift is available in ", ", ", and 6" stroke. Standard Swivel Top Linear-Lift- (7859-Series) Part Numbers 6 RPM Version RPM Version 0 Volt 5 Volt " Stroke 7859-60 7859-60 " Stroke 7859-60 7859-60 " Stroke 7859-60 7859-60 6" Stroke 7859-660 7859-660 0 Volt " Stroke 7859-0 " Stroke 7859-0 " Stroke 7859-0 6" Stroke 7859-60 Chain Drive Swivel Top Linear-Lift- (808-Series) Part Numbers 6 RPM Version RPM Version 0 Volt 5 Volt " Stroke 808-60 808-60 " Stroke 808-60 808-60 " Stroke 808-60 808-60 6" Sroke 808-660 808-660 0 Volt " Stroke 808-0 " Stroke 808-0 " Stroke 808-0 6" Stroke 808-60 Potentiometer Part Numbers If a Potentiometer is desired, order the Potentiometer Kit (Part No. 8) 8 MV7F

Swivel Top Linear-Lift Swivel Top Linear-Lift Installation Swivel Top Linear-Lift Installation Swivel Top Pulley/Sprocket Angle Adjustment (Cable Version) The Swivel Top Linear-Lift offers a variety of system cable routing options, and can be located in building corners where the system cables are routed directly away from the front of the Linear-Lift (See Figure below). Loosen the Nuts (Item, Figure ), to adjust for Pulley angle, then retighten once the desired angle has been achieved. Mv7-00 06/0 Item Description Swivel Top Linear Lift (Front View) Swivel Top Linear Lift (Top View) Adjustment Nuts Figure. Swivel Top Pulley/Sprocket Angle Adjustment (Cable Version) Swivel Top Pulley/Sprocket Angle Adjustment (Chain Version) To adjust the Chain-Drive Version, loosen the Nuts, (Item, Figure ) swivel the Pulleys to the desired angle and re-tighten. The Adjustment Bolts (Item ) should rotate freely to allow the chain to line up correctly with the Sprockets. If necessary, use a /6 Allen wrench to turn the adjustment bolts for proper alignment of the chain. Caution: Do not break the Adjustment Bolts loose!! Only turn them for proper chain alignment. Mv7-0 07/0 Item Description Adjustment Nut Adjustment Bolts Figure. Swivel Top Pulley/Sprocket Angle Adjustment (Chain Version) MV7F 9

Swivel Top Linear-Lift Installation Swivel Top Linear-Lift "To the Side" Cable/Chain Routing Systems If your cables/chains are routed "to the sides", as opposed to straight away from the Lift, use the Lag Screws provided for mounting. (Figure below). All Lag Screw Locations are shown in detail in Figure. To the Side Cable Routing Lag Screws (Supplied) MV7-06 06/0 Figure. Adjusting Swivel Angle (Cable Version Shown) "Straight-Off" Cable/Chain Routing Systems If both cables are to be routed "straight off" of the front of the unit, (Figure 5), consider using Through-Bolts to secure the top of the LIFT to the supporting wall. Use the top 8 mounting holes, minimum. See Figure 6 on the next page, for all mounting hole locations. Straight Away Cable Routing Top 8 Mounting Holes 5/6 or /8 Bolts Through-Bolts (Not Provided) Wall Mv7-0 06/0 Figure 5. Swivel Top Linear-Lift Installation (vertical wall view of Cable Version Shown) 0 MV7F

Swivel Top Linear-Lift Swivel Top Linear-Lift Installation Ceiling Installations The Swivel Top Linear-Lift is designed to be mounted on any ceiling where the slope of the ceiling is : or steeper (See Figure 6 below). This allows the cable to be routed off the end of the unit for systems where whole house control of both sides of the house with one unit is needed. Use (8) /8" Lag Screws, (included in Hardware Package), to attach the unit to the ceiling. Figure 6. Swivel Top Linear-Lift Installation (Ceiling Mount) Mv7-07 06/0 If the LIFT is to be installed on the ceiling, the vent plug must be installed next to the ceiling (upward) once mounted. Replace the vent plug with the solid steel plug from the opposite side of the gear housing. Refill oil in the gear housing before operating. (See Figure 7) For additional information, See Figure, on Page 5. It may be necessary to provide a recess in the mounting surface for clearance of the 90 Elbow and vent plug, or by mounting the Swivel Top Linear-Lift on x 0 lumber as shown for vent plug clearance (Figure 7 below). Item Description Part No. Power Unit Varies (See Page, and ) Swivel Top Linear Lift Varies -/" Lumber 90 Elbow 505 5 Vent Plug 5 5 Mv5-007 0/0 Figure 7. Swivel Top Linear-Lift Installation (ceiling mount) MV7F

Swivel Top Linear-Lift Installation Swivel Top Linear-Lift Mounting Hole Locations Mv7-00 05/0 Item Description Cable Routing Swivel Top Linear-Lift Mounting Hole Locations (Typical Both Sides) Figure 8. Swivel Top Linear-Lift Mounting Hole Locations MV7F

Swivel Top Linear-Lift Swivel Top Linear-Lift Installation Ceiling Mount Swivel Top Linear-Lift Installation 5 6 8 7 MV5-6 7/99 Item Description Part No. Pulley Assembly NY.5 777 Single Pulley Assembly 70 Anti-Slack Weight or Spring Curtain Cable 976 (7 * 9-/6" Dia.) Recommended 5 Swivel Top Linear-Lift Varies 6 Hand Winch Winch Mounting Assembly 9 7 Tie Down 8 () Cable Clamp 7 Figure 9. Ceiling Mounted Swivel Top Linear Lift pulling () curtains (top view) with a : double-back cable arrangement Two-Side Tunnel Curtain Application 6 5 Item Description Part No. Pulley Assembly NY.5 777 Single Pulley Assembly 70 Tie Down Curtain Cable 976 (7 * 9-/6" Dia.) Recommended 5 Swivel Top Linear-Lift Varies 6 Hand Winch Winch Mounting Assembly 9 Mv7-08 6/0 Figure 0. Wall Mounted (Corner) Swivel Top Linear-Lift pulling () curtains (top view) MV7F

Swivel Top Linear-Lift Installation Swivel Top Linear-Lift Side Wall Swivel Top Linear-Lift Installation 5 6 7 5 Item Description Part No. Pulley Assembly NY.5 777 Single Pulley Assembly 70 Anti Slack Weight or Spring Curtain Cable 976 (7 * 9-/6" Dia.) Recommended 5 Swivel Top Linear-Lift Varies 6 Hand Winch Winch Mounting Assembly 9 7 Tie Down Mv7-00 05/0 Figure. Side Wall Swivel Top Linear-Lift with a : double-back cable arrangement (top view) Side Wall Swivel Top Linear-Lift Installation 5 6 Mv7-00 05/0 Item Description Part No. Tie Down Pulley Assembly NY.5 777 Swivel Top Linear-Lift Varies Hand Winch Winch Mounting Assembly 9 5 Curtain Cable (7 * 9-/6'' Dia.) 976 Recommended 6 Curtain Figure. Side Wall Swivel Top Linear-Lift with a : double-back cable arrangement (front-view) MV7F

Swivel Top Linear-Lift Swivel Top Linear-Lift Installation Alternative Vent Plug Locations for Various Swivel Top Linear-Lift Mountings Refer to the four mounting diagrams shown (Figure ) to determine the correct Vent Plug location. Fill Level Fill Level Wall Mount (Horizontal) Wall Mount (Horizontal) Fill Level Fill Level Ceiling Mount (Horizontal) Mv5-00 0/0 Wall Mount (Vertical) Item Description Part No. / Solid Pipe Plug 755 / Pipe Plug (Magnetic) 060 / Vent Plug 5 90 Elbow 505 Figure. Vent Plug and Fill Level Locations MV7F 5

Swivel Top Linear-Lift Installation Swivel Top Linear-Lift Oil Recommendation The gearhead contains.5 oz. of SAE 0 oil. For horizontal and ceiling mounted Swivel Top Linear Lifts, fill the oil to the fill hole. For vertical mounted Swivel Top Linear Lifts fill the oil to approximately ounces above the fill hole. See Figure for oil fill locations. Grease Recommendation The Swivel Top Linear-Lift is fully greased at the factory. However, for maximum life, Chore-Time strongly recommends greasing the Swivel Top Linear-Lift at each grease fitting monthly. Recommended Grease: Sunoco Construction Grease, Mobile CMP Grease, or similar water-resistant with molybdenum, extreme pressure (E.P.) grease. (See Figure ) Important! Important! Grease Fittings on the Bronze Machined Nut and Pulleys are not labrynth sealed. Apply grease liberally. Also apply grease to Threaded Rod across full length. Grease every 0 days for maximum life. Mv7-005 05/0 Item Description Machined Nut Grease Fitting Figure. Swivel Top Linear-Lift Critical Grease Fitting Locations (horizontal wall mount view) 6 MV7F

Swivel Top Linear-Lift Swivel Top Linear-Lift Stop Switch Adjustment Swivel Top Linear-Lift Stop Switch Adjustment The Swivel Top Linear-Lift has two adjustable stops (Set Collars) that may be moved to accommodate a variety of curtain opening sizes. A /" Allen wrench is required to loosen the set screw on the Set Collar (Items and, Figure 5). Slide the Set Collar(s) on the Switch Rod to the desired limits of Inlet operation or Curtain travel (Figure 5). Two Collars are supplied for each limit of travel for best grip and shut off. Important! Do not adjust the four Collars on the rod nearest the Motor. These are set at the factory for switch operation and do not require moving. MV7-006 06/0 See Page 8 for Travel Lengths Item Description Switch Rod Adjustable Stops (set collar) Second Limit Stops (Adjust with Item ) Wiring Diagrams Figure 5. LINEAR LIFT Adjustment (side view) Limit Switch and Schematic Diagram for Standard & Chain Models EXTEND EXTEND RETRACT RETRACT # # # # Power Unit 5/0 V 50/60 Hz BLACK RED GREEN GREEN RED BLACK WHITE L L FROM (UP) EXTEND OUTPUT OF CONTROL L FROM (DOWN) RETRACT OUTPUT OF CONTROL GROUND BLACK WHITE WHITE MV5-5 /99 WHITE GREEN BLACK RED GREEN Figure 6. -Switch Wiring Diagram RED MV7F 7

Swivel Top Linear-Lift Switch Assemblies Swivel Top Linear-Lift Swivel Top Linear-Lift Switch Assemblies Swivel Top Linear-Lift Switch Assembly #7875 A 6 5 6 B A 7 B 8 Section A-A 9 8 7 0 5 6 7 SECTION B-B Mv7-007 05/0 Item Description Part No. Item Description Part No. Liquid Tight Connector 779 0 Twin Helix Screw #0x.75 6980 Pan Head Screw -0x 8 #0- Lock Nut 09 Hex Nut -0 5 Hex Screw Sltd. #0-6-6 Swivel Top Linear-Lift Motor Brkt Rh 776 Danger Decal 57-5 5 Switch, Micro 6 Poly Switch Plate 880 6 Switch Insulation 907-8 5 Neoprene Switch Plate 880 7 Terminal Box 6 6 Switch Plate 880 8 Gasket 6777 7 Switch Hook 880 9 Switch Box Cover 6776 Figure7. Switch Assembly 8 MV7F

Swivel Top Linear-Lift Optional Pulleys and Accessories Optional Pulleys and Accessories 7 6 5 7 5 9 0 8 8 9 6 Mv7-008 05/0 Item Description Part No..5" Corner Pulley Assembly 5597.5" Double Pulley Assembly 777.5" Pulley Kit 70.5" Center Pulley Assembly 70 5 /6" Cable (50') 7 * 9 Weave 976 6 /6" Cable Clamp 7 7.5" Pulley Assembly 500 8 Double Pulley Mounting Brkt. 50 9 Single Pulley Mounting Brkt. 505 0 /8-6 x.5" U Bolt with Nuts 560 5/6-8x7" Bolt -0.5" Double Eye Pulley 50.5" Steel Pulley Assembly 005.5" Steel Single Pulley Assembly 8 5.5" Steel Double Pulley Assembly 9 6.5" Pulley Assembly 89 7 Inlet Spring 8.5" Steel Double Pulley Assembly 0 9.5" Steel Corner Pulley Assembly Figure 8. Pulley Options Items 7, 8, 0, & may be ordered as a Double Pulley Bracket Kit. Part No. 5600. Items 7, 9, 0, & may be ordered as a Single Pulley Bracket Kit. Part No. 5598. MV7F 9

0 MV7F Swivel Top Linear-Lift Drawings and Parts Listings 7 Standard, 7859-Series Drawing 6 5 7 8 0 8 9 8 9 6 6 8 0 7 5 6 Straight Out Top Cap Version 0 5 5 Shown With Cover in Place 8 9 5 Mv7-009 06/0 7 0 Swivel Top Linear-Lift Drawings and Parts Listings Swivel Top Linear-Lift

MV7F Standard, 7859-Series Parts Listing Item Description Part No. 5 Volt Motor (60RPM) 0 Volt Motor (60 RPM) 0 Volt Motor (0 RPM) 780 670 88 Swivel Top Linear-Lift Base 6" 6" 8" 66" 786-6 786-6 786-8 786-66 * Linear-Lift Switch 7875 L.H. Linear-Lift Motor Bracket 776 5 Linear-Lift Thrust Bracket 776 6 R.H Linear-Lift Panel 777-7 L.H Linear-Lift Panel 777-8 Linear-Lift Swivel Partition 777 9 Linear-Lift Cover Bracket 78 0 Flexible Type L Coupling 66- Flexible (Mach.) Coupling 59 "SOX" Spider Spacer 6 5/6 x Clevis Pin 666-.5 x.75 Cotter Pin 66 5 /6 x Square Key - 6 Industrial Thrust Bearing 697 7 Chore-Time Decal 55-8 Machined Linear-Lift Nut 7759 9 Red Pulley Wheel 50 0 Retainer Ring 55 Compression Spring 98 Lower Linear-Lift Cover 785- Set Collar 857 Grease Decal 59-6 *See Figure 6 for exploded view of parts. Item Description Part No. 5 Linear-Lift Switch Rod 6" 6" 8" 66" E0-6.50 E0-6.50 E0-58.50 E0-76.50 6-5 Threaded Acme Shaft 6" 6" 8" 66" 7 Swivel Top Pulley Assembly Straight Out Top Cap Assembly 8 Linear-Lift Cover Assembly 6" 6" 8" 66" 7856-6 7856-6 7856-8 7856-66 7876 50559 787-6 787-6 787-8 787-66 9 Handle -9 0 5 Linear-Lift Cable 7658 8- Set Screw 78 Cable Tie 665 5/6-8 x.65 Carriage Bolt 88 5/6-8 Hex Flange Nut 890 5 /-0 Hex Flange Nut 08 6 5/6 x 8 x.5 Bolt 50 7 Linear-Lift Decal Varies 8 5/6-8 x.50 Bolt 89 9 0 Danger (Rotating Parts) Decal 57-0 Swivel Top Linear-Lift Swivel Top Linear-Lift Drawings and Parts Listings

MV7F 7 5 0 Chain Drive, 808-Series Drawing 6 5 7 8 8 0 9 8 9 6 6 0 6 5 Shown With Cover in Place 5 9 5 6 8 0 7 5 MV7-09 07/0 7 7 Swivel Top Linear-Lift Drawings and Parts Listings Swivel Top Linear-Lift

MV7F Chain Drive, 808-Series Parts Listing Item Description Part No. 5 Volt Motor (60RPM) 0 Volt Motor (60 RPM) 0 Volt Motor (0 RPM) 780 670 88 Swivel Top Linear-Lift Base 6" 6" 8" 66" 786-6 786-6 786-8 786-66 * Linear-Lift Switch 7875 L.H. Linear-Lift Motor Bracket 776 5 Linear-Lift Thrust Bracket 776 6 R.H Linear-Lift Panel 777-7 L.H Linear-Lift Panel 777-8 Linear-Lift Swivel Partition 777 9 Linear-Lift Cover Bracket 78 0 Flexible Type L Coupling 66- Flexible (Mach.) Coupling 59 "SOX" Spider Spacer 6 5/6 x Clevis Pin 666-.5 x.75 Cotter Pin 66 5 /6 x Square Key - 6 Industrial Thrust Bearing 697 7 Chore-Time Decal 55-8 Machined Linear-Lift Nut 7759 9 Red Pulley Wheel 50 0 Retainer Ring 55 Compression Spring 98 Lower Linear-Lift Cover 785- Set Collar 857 Grease Decal 59-6 5 Linear-Lift Switch Rod 6" 6" 8" 66" E0-6.50 E0-6.50 E0-58.50 E0-76.50 *See Figure 6 for exploded view of parts. Item Description Part No. 6-5 Threaded Acme Shaft 6" 6" 8" 66" 7856-6 7856-6 7856-8 7856-66 7 Swivel Top Pulley Assembly Swivel Top Sprocket Assembly Top Cap Assembly 8 Linear-Lift Cover Assembly 6" 6" 8" 66" 7876 7866 50559 787-6 787-6 787-8 787-66 9 Handle -9 0 Drive Chain 6" 6" 8" 66" 05-05-5 05-7 05-9 8- Set Screw 78 Cable Tie 665 5/6-8 x.65 Carriage Bolt 88 5/6-8 Hex Flange Nut 890 5 /-0 Hex Flange Nut 08 6 5/6 x 8 x.5 Bolt 50 7 Linear-Lift Decal Varies 8 5/6-8 x.50 Bolt 89 Danger (Rotating Parts) Decal 57-0 5 Chain Connecting Rod 7 6 Connecting Link (#0) 007 7 /-0 x -/ SH Cap Screw 508- Swivel Top Linear-Lift Swivel Top Linear-Lift Drawings and Parts Listings

Swivel Top Linear-Lift Drawings and Parts Listings Swivel Top Linear-Lift Made to work. Built to last. Note: The original, authoritative version of this manual is the [English] version produced by CTB, Inc. or any of its subsidiaries or divisions, (hereafter collectively referred to as "CTB"). Subsequent changes to any manual made by any third party have not been reviewed nor authenticated by CTB. Such changes may include, but are not limited to, translation into languages other than [English], and additions to or deletions from the original content. CTB disclaims responsibility for any and all damages, injuries, warranty claims and/or any other claims associated with such changes, inasmuch as such changes result in content that is different from the authoritative CTB-published [English] version of the manual. For current product installation and operation information, please contact the customer service and/or technical service departments of the appropriate CTB subsidiary or division. Should you observe any questionable content in any manual, please notify CTB immediately in writing to: CTB Legal Department, P.O. Box 000, Milford, IN 65-000 USA. Revisions to this Manual Page No. Description of Change 8 Changed 775 Kepnut to 09 Locknut Contact your nearby Chore-Time distributor or representative for additional parts and information. CTB Inc. P.O. Box 000 Milford, Indiana 65-000 U.S.A. Phone (57) 658-0 Fax (877) 70-885 E-Mail: ctb@ctbinc.com Internet: http//www.ctbinc.com Printed in the U.S.A. MV7F