Model 1929 Parts Conversion Chart This list to be used if you have a Model 1929 Newgy Table Tennis Robot and you are looking for a Robo-Pong 2000 part that will substitute for it. 1929 Part # 1929 Part Name 2000 Part # 2000 Part Name Notes 752-201 Center Trough Assembly mismatch different shape, color 752-202 Metal Net Support mismatch not used 752-204 Center U Support Upright mismatch diff. size 752-205 Back Support Plate mismatch not used 752-206 Net Support Tube Curved mismatch diff. length, curve 752-207 Support Leg, L mismatch diff. size, curve, can use 2000-110 if it is bent slightly so robot sits level on table 752-208 Front Support Plate mismatch diff. attachment 752-209 Net Support Plate, Front mismatch diff. shape, size, color 752-210 Net Support Plate, Rear mismatch diff. shape, size, color 752-212 Support Leg, R mismatch diff. size, curve, can use 2000-112 if it is bent slightly so robot sits level on table 752-213 Net Support Tube, Straight mismatch diff. length 752-217 Net mismatch diff. shape, size 752-219 1/4x3/4 Phillips Head mismatch not used 752-225 #8x1" Machine s mismatch diff. thread, can use 2000-302 if replaced along with 2000-310 752-227 #8-32 Hex Nut mismatch diff. thread, can use 2000-310 if replaced along with 2000-302 752-228 Large Flat Washer mismatch not used 752-229 Rubber Crutch Tip 2000-118 CT Support Leg Tip, 1" 752-230 1/4-20 Wing Nut mismatch different size, thread 752-232 1/4-20 Hex Nut mismatch not used 752-236 1/4-20 x 1" Hex Bolt mismatch not used 752-302 Ball Return Tray, L mismatch different shape, size, color 752-303 Ball Return Tray, R mismatch different shape, size, color 752-304 Tray Strap 2000-140 Tray Strap 753-101 Back Panel mismatch diff. color, support wings finished on opposite side, can use 2000-142 if you round off top tab & widen opening in bottom of support flange and you
replace it along with 2000-146, 2000-156, 2000-154, & 2000-318 753-101N New Back Panel mismatch diff. color, support wings finished on opposite side, can use 2000-142 if you round off top tab and widen opening in bottom of support flange 753-102 Front Panel 2000-162 Front Cover diff. color, shape, could be used for 2000-162 if necessary, but may interfere with ball channeling 753-103 Ball Return Plate 2000-144 Ball Feed Collector Plate diff. color, not normally seen (covered by balls) 753-104 Ball Return Housing mismatch diff. shape, color, attachment 753-105 Ball Return Adapter 2000-196 Oscillator Pivot Guide 753-106 Pan. s & Motor Hsng. 2000-204 Oscillator Motor Cover 753-107 Ball Discharge Tube 2000-166 Ball Feed Discharge Tube 753-108 Ball Discharge Housing, L 2000-172 Robot Head Housing, L., not easily seen 753-109 Ball Discharge Housing, R 2000-174 Robot Head Housing, R. 753-110 Pan. Motor & Frame 2000-206 Osc. Motor Mounting Plate diff. color, not visible on outside, if replacing 753-110 with 2000-206, use only 2000-326 screws 753-111 Ball Return Motor & Housing mismatch not used, can use 2000-146 if replaced along with 2000-156, 2000-154, 2000-318, & 2000-142. 753-111A Ball Feed Back Plate 2000-146 BF Mounting diff. color, not easily seen Plate 753-111B New Ball Feed Motor Frame 2000-156 BF Motor Mount Housing 753-111C Ball Feed Brass Posts 2000-154 BF Transfer Brass Shaft diff. color, not easily seen 753-111D s For 753-111A 2000-318 BF #4x5/16 Machine 753-112 Control Lever Adapter mismatch diff. shape, color, can use 2000-198 if replaced along with 2000-200 & 2000-202 753-112N New Control Lever Adapter 2000-198 Osc.Control Lever diff. color, includes lever guard Adapter 753-113 Friction Block mismatch diff. color (not easily seen), tabs are shorter, can use 2000-192 if replaced along with 2000-190, 2000-184, & 2000-324
753-113N New Friction Block 2000-192 Ball Feed Friction diff. color, not easily seen Block 753-114 Old Ball Discharge Wheel mismatch not used, has small undulations in wheel surface, can use 2000-190 if 184, and 2000-324 753-114N New Ball Discharge Wheel 2000-190 Ball Speed diff. color, not easily seen Discharge Wheel 753-115 Motor Cap-Ball Discharge 2000-188 Ball Speed Motor Cover diff. color 753-116 Ball Return 2000-148 Ball Feed Main diff. color, not normally seen (covered by balls) 753-117 Osc. Motor & Pinion 2000-148 Osc. Motor W/Brass 753-117W Oscillator Wire 2000-210 Osc. Power Wire 753-118 Control Lever, R mismatch diff color, shape, can use 2000-202 if replaced along with 2000-198 & 2000-200 753-118N New Control Lever, R 2000-202 Control Lever, R diff. color 753-119 Control Lever, L mismatch diff color, shape, can use 2000-200 if replaced along with 2000-198 & 2000-202 753-119N New Control Lever, L 2000-200 Control Lever, L diff. color 753-120 Ball Discharge Knob Nut as 753-227 753-121 Ball Discharge Tube Pivot 753-123 Ball Fingers 2000-150 BF Main Fingers 753-124 Motor Bracket 2000-212 Osc.Motor Mount Bracket 753-125 & Pinion Cluster 2000-152 BF White Transfer 753-126 Panning Drive 2000-216 Osc. White Drive 753-128 Brake-Ball Discharge Tube 2000-168 BF Discharge Tube Brake 753-129 Horizontal Pointer 2000-182 Robot Head Angle Pointer as 753-143 diff color, not normally seen (covered by balls) 753-138 Ball Discharge Adjusting Knob mismatch diff. thread, can use 2000-180 if replaced along with 2000-322 753-139 Ball Discharge Comp. Spring 2000-178 RH Steel Ball Spring
753-140 Friction Block Spring 2000-194 BS Friction Block Spring 753-141 Ball Sp. Motor & Pinion mismatch diff. size drive shaft, has right hand threads in shaft, can use 2000-184 if 190, and 2000-324 753-141N New Ball Speed Motor 2000-184 BS Motor W/Brass Shaft 753-141W Ball Speed Coiled Cord 2000-186 BS Coiled Power Wire (has left hand threads in shaft) 753-142 Oscillator Washer mismatch not used (2000-326 has washer-type head) 753-143 #4x3/8 Self Tap, Bl. 2000-328 #4x3/8 Self Tap 753-144 #4x3/8 Self Tap, Gld mismatch not used, can be substituted for 2000-328 753-145 Ball Discharge Wheel mismatch right hand threads, can use 2000-324 if 190, and 2000-184 753-145N Ball Discharge Wheel, 2000-324 BS Discharge, left hand threads (L Thread) Wheel 753-146 Ball Disc. Whl. Lock Washer mismatch not used 753-147 #1x3/16 Thread Form. mismatch diff. thread, use 753-147 only with 753-110 that has solid plastic posts, do not use if 753-110 has brass posts (use 2000-326 instead) 753-148 Ball Feed Motor & 2000-158 BF Motor W/Brass 753-148W Ball Feed Wire 2000-160 BF Power Wire 753-149 #8 x 5/16 Self Tap. mismatch not used 753-150 Ball Discharge Spring 2000-170 Ball Feed Discharge Spring 753-151 5 Pin Receptacle 2000-218 5 Pin Connector 753-152 Connector Cable 2000-220 Connector Cable end terminals not removable 753-153 Ball Feed Washer 2000-314 Large Washer 753-154 Steel Ball 2000-176 Robot Head Steel Ball 753-155 Ball Disc. Housing 2000-320 RH #8x1 3/16 Machine Scw 753-156 3/16 Motor Mount 2000-330 #2x1/4 Machine has washer type head, washer not necessary
753-232 3/4 Shoulder Bolt For Trays mismatch not used 753-232A 3/8 Lock Nut For Trays mismatch not used 753-350 Control Box 2000-224 Control Box different electronics, labels, has Pong- Master connection 753-350-1 Voltage Regulator (Q1&Q3) 2000-224-8 Osc. & Ball Speed Voltage Regulator 753-350-2 Voltage Regulator (Q2) 2000-224-7 Ball Frequency Voltage Regulator 753-350-5 Small Capacitor (C1 C4) 2000-224-25 Tiny Capacity Same 753-350-6 Large Capacitor (C5) mismatch both leads at one end 753-350-7 Resistor (R1 & R3) mismatch not used 753-350-8 Resistor (R2) mismatch not used 753-350-9 Ball Speed Potentiometer mismatch longer leads with different shape 753-350-10 Ball Freq. Potentiometer mismatch longer leads with different shape, diff range 753-350-11 Osc. Speed Potentiometer mismatch longer leads with different shape 753-350-15 Power Jack 2000-224-6 Power Jack 753-350-16 Lighted Power Switch 2000-224-17 Lighted Power Switch 753-350-25 Foam Pad For Control Box 2000-224-18 Control Box Foam Pad 753-350-26 Control Box Knobs 2000-224-12 Control Box Knob 753-450 Transformer 2000-222 Transformer Cord 900-125 Owner's Manual mismatch not the 900-130 Ball Dams (Pair) mismatch diff. shape, size, color 900-134 End Fitting For Conn Cable mismatch not used