INTERIOR LED LIGHTING KIT P/N 2880549 APPLICATION SLINGSHOT BEFORE YOU BEGIN Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information. 2 1 KIT CONTENTS Ref Qty Part Description Part Number 1 1 Wire Harness 2412970 APPROXIMATE ASSEMBLY TIME 0-45 mins 2 1 Switch 4015097 6 Zip Tie 708018 TOOLS NEEDED 1 Instructions 9925468 2/64 Drill bit /8 Drive Socket Wrench 6 mm Hex Bit (M6) Socket (/8 ) Power Drill Socket Extension (/8 ) 10 mm Socket (/8 ) P/N 9925468 Rev 01 08/14 Page 1 of 9
IMPORTANT This SLINGSHOT INTERIOR LED LIGHTING KIT is exclusively designed for use with this vehicle. Please read the installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown. INSTALLATION INSTRUCTIONS Mounting Preparation: 1. Move the vehicle to its final position. Place the vehicle in NEUTRAL and turn the key to OFF position. Remove the key from the vehicle. Apply the parking brake. 2. Remove center/dash console as shown in Figures 1 and 2: a. Pull the console (A) out. b. Pull up and out to remove and open the hood (B). If a radio is present, remove according to service manual. A Figure 1 B Figure 2 P/N 9925468 Rev 01 08/14 Page 2 of 9
. Locate ECU mounting bracket (D) in back left of engine. Remove two 6 mm hex bolt (C), as shown in Figure a. Remove one 6 mm hex bolt (F) on other side of bracket as shown in Figure 4. Optional: for additional ease of removal of third 6 mm hex bit, remove two 10 mm bolts (E) indicated in Figure b and shift ECU (D) out of the way. C Figure a E Figure b D F Figure 4 P/N 9925468 Rev 01 08/14 Page of 9
4. Shift mounting bracket towards the front of the vehicle, away from area for the LED s, as shown in Figure 5. ECU Unit and Mount (D) D Left LED Mounting Area Move ECU Unit in this direction Figure 5 ECU Mounting Area 5. Drill two 2/64 sized holes (G) upward by the driver side feet as indicated in Figure 6a. Insert black locking fasteners (J) into the holes from above on the engine side (see Figure 6c for fastener (J) image shown in white for clarity). Clutch Pedal - (H) 6. Drill two 2/64 sized holes (G) upward by the passenger side feet as indicated in Figure 6b. Insert black locking fasteners into the holes from above on the engine side (see Figure 6c for fastener (J) image, shown in white for clarity). Figure 6a G H G Figure 6b Supporting Frame near Passenger Feet Direction to insert Clips to hold fastener in place Figure 6c J P/N 9925468 Rev 01 08/14 Page 4 of 9
7. Remove rightmost switch blank (K) in center console as shown in Figure 7. To remove switch push the fastener clips (L) towards center and try to push it up. Refer to Figure 8 for switch removal. K Figure 7 Push clips towards center and push clip out to remove L Figure 8 LED and Switch Installation: 1. Locate wiring harness and LED s for following steps, Refer to Figure 9 for orientation of installation. Power Terminal - (M) LED ON/OFF Connection Harness - (N) Ground Terminal - (P) Left Side LED s Right Side LED s M N Figure 9 P Driver Side Passenger Side P/N 9925468 Rev 01 08/14 Page 5 of 9
2. Feed the wire harness without the power terminal, as shown in Figure 10, starting from inside the console. Feed left side wires and LED s left out into the engine area, along the existing wiring to the drilled holes, as shown in Figure 11. Feed wires here Figure 10. Feed left LED wires along the existing wiring harness, according to Figure 9, zip tying wiring approximately in the areas indicated in Figures 11a, 11b, and 11c. Figure 11a Approximate Left LED Location Figure 11b P/N 9925468 Rev 01 08/14 Page 6 of 9
Left LED Wires: Zip Tie from Fig. 11b Zip Tie from Fig. 11a Figure 11c Zip Tie to Original Harness 4. Feed right LED wires out the back of the console to the right, under the overflow coolant container, and zip tie along existing wiring, ensuring to stay clear of the exhaust, and as indicated in Figures 12a and 12b. Approximate Right LED Location DC Power Outlet Location Right LED Wires: Figure 12a Zip Tie from 12a Figure 12b P/N 9925468 Rev 01 08/14 Page 7 of 9
5. Disconnect wire from center terminal at DC power socket (backside of cigarette outlet inside the glovebox in the passenger side). Connect power terminal (M) to the center terminal of the DC power unit inside the glovebox in the passenger side. Then connect the Power Mate terminal (Q) to the original power connection. See Figures 1a and 1b, refer to Figure 12a for outlet location. DC power socket Figure 1a Center Terminal Connection Ground Terminal 1 M Q Figure 1b Ground Terminal LED On/Off Connection Port 6. Insert left and right LED s (R) into the holes of the black locking fasteners (shown in white for clarity). Ensure they are entirely inserted into the openings as indicated in Figure 14. R Completely inserted Only partially inserted Figure 14 7. Insert switch into vacated switch slot and connect LED On/Off connection harness to the switch (2) by simply inserting harness into the switch terminals as illustrated in Figure 15. There is only one orientation in which the connector can be inserted. 2 Figure 15 Connect LED On/ Off Connection Harness here P/N 9925468 Rev 01 08/14 Page 8 of 9
8. Connect ground terminal to the black/ white ground wire plug located inside the center console as indicated in Figure 16. Refer to Figure 9 for ground terminal. Black/White Ground Plugin Figure 16 9. Reinstall ECU bracket, unit and center console (or radio) according to service manual and the reverse of steps (, 2, 1) from mounting preparation. P/N 9925468 Rev 01 08/14 Page 9 of 9