HC Hydraulic Crawler Crane t Lifting Capacity HC HYDRAULIC CRAWLER CRANE 410 Stevenson Dr, Bolingbrook, IL 4 6-972-9199 16675 Van Dam Rd, South Holland IL 473 219-972-9199 www.stevensoncrane.com
(73 mt) tons maximum lifting capacity 0 ft (61 m) maximum length of main boom 1 + ft (52 + 18 m) maximum boom and jib HC HIGHLIGHTS 2 ft (73 m) max. boom and luffing jib length Power up/down and freefall on main, auxiliary and optional third drum Quiet, spacious operator s cab Excellent visibility Two speed travel Superior transportability 88,000 lb (39 917 kg) transport weight includes sideframes and boom inner 2 HC
CRAWLER CRANE HC CONTENTS Page: Specifications Dimensions....................................................................................................... 4 1 Main boom Range Diagram, 47HI Boom........................................................................................... 6 With 47HI Offset Tip Boom and 58, Pound Counterweight.................................................................. 7 Range Diagram, 46HI Boom........................................................................................... 11 With 46HI Angle Boom, 4 Sheave Tip and 58, Pound Counterweight........................................................... 12 Jib Range diagram, 47HI Boom, #9HL Jib.................................................................................... 16 With 47HI Boom, #9HL Jib and 58, Pound Counterweight.................................................................. 17 Range diagram, 46 HI Boom, #9 Angle Jib................................................................................. 21 With 46HI Boom, #9 Angle Jib and 58, Pound Counterweight................................................................ 22 2 3 Technical description Hydraulic Crawler Crane.............................................................................................. 28 4 Transport example for HC................................................................................................................ 29 5 HC 3
DIMENSIONS 4 HC
CRAWLER CRANE HC DIMENSIONS 1 HC 5
RANGE DIAGRAM, 47HI BOOM 6 HC
CRAWLER CRANE HC WITH 47HI OFFSET TIP BOOM Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 11 12 15 58, lb 3 (12.2 m) Boom length.5 79.0 74.6 67.0 58.8 49.9 39.5.8 (15.2 m) Boom length 13.1 15 77.8 71.8 65.6 59.1 52.0 44.2 22.9 (18.3 m) Boom length 14.8 15 79.8 74.9 69.9 64.7 59.2 53.4.2.8 (21.3 m) Boom length 16.5 77.1 72.9 68.5 64.0 59.3 49.2 37.0 19.2 1,000 * 1,000 * 141,4 87,810 63,3 49,3,3 33,9 44 42 36 31 23 1,000 * 55 141,4 54 87,7 53 63,2 51 49,2 48,2 33,8,5 1,3 * 65 141,3 64 87,6 63 63,1 62 49,, 57 33,7 54,0 44,2 27 1,0 * 74 87,5 74 63,0 72 49,0 71,0 68 33,6 66,310 58,1 48 16,5 28 (24.4 m) Boom length ANSI B.5 Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 17.9 78.8 75.1 71.3 67.5 63.5 55.1.8 34.5 17.9 (27.4 m) Boom length 19.7.0 76.8 73.5.1 66.7 59.5 51.7 43.0 32.5 16.9 (.5 m) Boom length 21.4 78.1 75.2 72.2 69.1 62.8 56.1 48.9.7.7 16.0 (33.5 m) Boom length 22.8 79.2 76.5 73.8 71.1 65.5 59.6 53.3 46.4 38.7 29.2 15.2 109,2 * 84 87,4 84 62,9 83 48,8 81 39,8 79 33,4 77,1 71,000 63 16,4 51 13,8 94,5 87,3 62,810 48,7 39,7 33,3 24,9 19,8 16,2 13,6 11,6,910 62,6 48,5 39,5 33,1 24,8 19,7 16,1 13,5 11,5 10,010 94 94 93 92 88 83 76 67 54 32 104 103 102 101 99 94 88 81 71 56 33 72,0 * 114 62,5 113 48,4 112 39,4 111 33,0 109 24,6 105 19,5 15,9 94 13,3 85 11,3 74 9,8 59 8,5 34 2 KEY Counterweight CB Central ballast HC 7
WITH 47HI OFFSET TIP BOOM 58, lb 3 (36.6 m) Boom length Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 24.6.1 77.7 75.2 72.7 67.6 62.3 56.8.8 44.3 37.0 28.0 14.5 1 (39.6 m) Boom length.9 78.6 76.4 74.1 69.4 64.7 59.6 54.4 48.7 42.5.4 26.8 1 13.9 1 (42.7 m) Boom length 27.7 79.5 77.4 75.3 71.0 66.6 62.0 57.3 52.2 46.8.9 34.1 1.8 1 13.4,1 *,1 * 48,2 39,2 32,8 24,4 19,3 15,0 13,1 11,210 9,6 8,410 7,3 124 124 123 121 116 112 106 98 89 78 62 36,9 * 134 48, 133 39, 132 32,0 1 24,3 127 19,2 123 15,6 118 13,0 111 11,0 103 9,510 93 8,2 81 7,2 64 6,3 37 42,3 * 42,3 * 38,9 32,5 24,1 19,0 15,4 12,8 10,8 9,3 8,0 7,0 6,1 5,4 144 143 142 141 138 134 129 123 116 108 97 84 66 38 ANSI B.5 1 (.7 m) Boom length Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 28 1 1 1.9.2 78.2 76.3 72.3 68.2 64.0 59.7 55.1.3.1 39.4 32.9 24.9 12.9 1 (48.8 m) Boom length.8 79.0 77.1 73.4 69.7 65.8 61.8 57.6 53.2 48.6 43.6 1 38.1 1 31.8 1 24.1 1 12.5 1 (51.8 m) Boom length 31 81.0 79.6 77.9 74.4.9 67.3 63.6 59.7 55.7 51.5 47.1 1 42.2 1 36.9 1.8 1 23.4 1 12.1 36,6 * 36,5 * 36,0 * 32,3 23,9 18,0 15,310 12,6 10,710 9,1 7,8 6,8 6,000 5,2 4,6 31,7 * 31,3 *,7 * 23,0 18,7 15,1 12,5 10,5 8,9 7,7 6,6 5,8 5, 4,4 3,9 27,710 * 27,3 * 26,810 * 23,610 18,5 14,9 12,3 10,3 8,0 7,5 6,510 5,6 4,9 4,2 3,7 3,2 154 153 152 151 148 1 1 1 128 121 112 101 87 69 39 163 162 161 159 155 151 146 141 134 1 116 104 71 173 173 172 169 166 162 158 152 146 139 1 108 93 73 41 8 HC
CRAWLER CRANE HC WITH 47HI OFFSET TIP BOOM 58, lb 3 1 (54.9 m) Boom length Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 33 1 1 1 1 1 1.9.2 78.6 75.3 72.0 68.6 65.1 61.6 57.9 54.0.0.7 41.0.8 29.9 22.7 11.8 24,2 * 24, * 23,210 *,0 * 18,410 14,0 12,1 10,1 8,6 7,3 6,3 5,4 4,7 4, 3,5 3,0 2,6 183 183 182 1 177 173 169 164 158 151 143 134 123 111 95 75 42 0 (61.0 m) Boom length ANSI B.5 Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 36 1 1 1 1 1 1 1 0.9 79.7 76.8 73.8.8 67.8 64.6 61.4 58.1 54.6 51.0 47.2 43.2 38.8 33.9 28.4 21.5 11.2 16,7 * 16,2 * 15,000 * 13,0 * 12,7 * 11,8 9,8 8,2 7,010 5,9 5, 4,3 3,7 3,1 2,710 2,0 1,9 1,5 * 3 2 0 198 194 191 186 181 175 169 161 152 142 131 117 79 44 2 1 (57.9 m) Boom length.7 79.2 76.1 73.0 69.8 66.5 63.2 59.8 56.2 52.5 1 48.5 1 44.4 1 39.8 1 34.8 1 29.1 1 22.1 1 11.5 19,3 * 18,6 * 17,3 * 16, * 14,6 12,010 10,0 8,4 7,0 6,1 5,2 4,5 3,9 3,3 2,910 2,0 2,1 193 192 1 187 184 1 175 1 163 156 148 138 127 114 98 77 43 HC 9
NOTES TO LIFTING CAPACITY! Warning This rating chart is invalid if the crane has been modified or altered by use of other than GENUINE AMERICAN PARTS as such modifications or alterations may affect its capacity or safe operation. See American Crane Corporation Service Bulliten #9. Ratings in this chart are in POUNDS and do not exceed the percentage of tipping specified for this crane by ANSI B.5. All ratings require that the crane be standing level on a firm uniformly supporting surface. Do not lift loads in excess of those shown on this chart. Lifting loads in excess of those shown or operation not in accordance with good operating practice, including limitations shown on page 3499 of Operator s Manual, can cause tipping, structural damage or catastrophic failure. Asterisk (*) areas on this chart indicate ratings which are limited by strength of material or factors other than stability (tipping). RADIUS IN FEET is the horizontal distance at ground level from the crane centerline of rotation to a vertical line through the center of gravity of the suspended load. When using the main boom fall with jib in place, the main fall ratings must be reduced by the jib effective weight shown on the jib rating chart plus twice the weight of all suspended blocks, slings, rope, etc., at the jib fall. See Appendix A. When using the main boom fall with boom tip extension in place, the main fall ratings must be reduced by the weight of the boom tip extension plus twice the weight of all suspended blocks, slings, rope, etc., at the boom tip extension fall. See Appendix A. Blocks, slings, buckets and other load carrying devices are considered part of the load. The weight of standard hoisting ropes for the rating at a given radius has been calculated as part of the boom point load and need not be considered in determining net allowable loads. See Appendix A. This chart was developed exclusively for use with a boom only. Under no circumstances are these ratings to be interpreted for use with a jib. Ratings shown on this chart make no allowance for such factors as out of plumb loads, wind, poor soil conditions, improper inflation of rubber tires and dynamic effects due to excessive operating speeds. The user (operator) must exercise judgement to make allowance for these conditions. See page 3499 of Operator s Manual for detailed information. No account is taken of the wind force on the load. This effect, which can be substantial for loads with large surface areas, must be considered by the user. In any wind it is strongly recommended that taglines be used to control the load. BOOM HOIST LINE is 14 parts of 5/8 inch diameter EIPS wire rope with a minimum breaking strength of 41,0 pounds. PENDANT SUSPENSION LINE is 2 parts of 1-1/4 inch diameter MONOLAY wire rope with a minimum breaking strength of 172,0 pounds. MAIN LOAD LINE is 7/8 inch diameter EIPS wire rope with a minimum breaking strength of 79,0 pounds. ERECTION Erection is with the A-Frame fully raised. Erection OVER THE END is with the boom over the idler end. Erection OVER THE SIDE is with the boom to the sideframes and with the side frames extended. Blocks, slings and other load carrying devices must be on the ground during erection. 10 HC
RANGE DIAGRAM, 46HI BOOM HC 11
WITH 46HI ANGLE BOOM, 4 SHEAVE TIP Boom 3 Degree From Boom Pt. Radius Angle Rating to Ground (Feet) (Degrees) (Pounds) (Feet) 10 12 15 58, lb 3 (12.2 m) Boom length.9 77.9 73.5 65.9 57.7 48.8 38.4 24.7 (15.2 m) Boom length 12.4 15 76.9.9 64.7 58.2 51.2 43.4 34.2 22.0 (18.3 m) Boom length 14.1 15 79.1 74.2 69.2 64.0 58.5 52.7 46.4 39.4 55 31.1.1 (21.3 m) Boom length 15.7 76.5 72.2 67.9 63.4 58.7 53.8 48.5 55 42.8 36.4 65 28.8 18.6 1,000 * 1,000 * 141,1 87,4 63,0 49,0,000 33,6 138,4 * 128,4 * 87,3 62,910 48,8 39,8 33,4 28,7,1 119,6 * 117,0 * 87,2 62,7 48,7 39,710 33,3 28,6,0 22,0 19,8 44 42 39 36 22 55 54 53 51 48 44 34 24 65 64 63 61 59 57 53 49 44 36 26 106,3 * 74 87, 73 62,610 72 48,5 39,5 68 33,1 65 28,4 62 24,8 58 22,000 53 19,6 47 17,7 39 16, 28 (24.4 m) Boom length ANSI B.5 Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 17 55 65 75.4 78.2 74.5.8 66.9 63.0 58.9 54.6.1.2 39.9 34.0 26.9 17.4 (27.4 m) Boom length 18.8 79.5 76.3 73.0 69.6 66.2 62.7 59.0 55 55.2 51.2 65 47.0 42.5 75 37.5 32.0 85.3 16.4 (.5 m) Boom length.6 77.7 74.7 71.7 68.7 65.6 62.4 55 59.1 55.7 65 52.2 48.4 75 44.5.2 85.6.3 95 24.0 15.5 94,3 * 84 87,000 84 62,4 83 48,410 81 39,0 79 33,0 77 28,0 74 24,6 71 21,8 67 19,5 62 17,0 57 15,9 14,5 42 13,3 29 84,4 * 82,2 * 62,0 48,210 39,0 32,810 28,0 24,4 21,6 19,3 17,3 15,7 14,3 13,1 12, 11,0 94 94 93 91 88 85 83 79 76 71 66 53 44 31 75,9 * 104 62, 103 48,010 102 39,0 32,6 99 27,8 96 24,2 94 21,4 91 19,1 88 17,0 84 15,5 14,1 75 12,9 11,910 64 10,9 56 10,1 46 9,4 32 12 HC
CRAWLER CRANE HC WITH 46HI ANGLE BOOM, 4 SHEAVE TIP 58, lb 3 (33.5 m) Boom length Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 21 55 65 75 85 95 105.9 78.8 76.1 73.4.7 67.9 65.1 62.2 59.2 56.1 52.9 49.6 46.0 42.3 38.3 33.8 28.8 22.9 14.8 (36.6 m) Boom length 23.7 79.7 77.3 74.8 72.4 69.8 67.3 55 64.7 62.0 65 59.2 56.4 75 53.5.5 85 47.3 44.0 95.4 36.6 105 32.4 27.6 115 21.9 14.2 68,9 * 114 61,9 113 47,0 112 38,810 111 32,0 109 27,6 107 24,0 105 21,2 103 18,9 16,9 97 15,3 93 13,9 89 12,7 85 11,0 79 10,7 74 9,9 67 9,2 58 8,5 48 7,9 33 61,3 *,000 * 47,6 38,6 32,2 27,0 23,8 21, 18,7 16,8 15,1 13,7 12,5 11,5 10,5 9,7 9,0 8,3 7,7 7,2 6,7 124 123 122 121 118 116 114 111 109 105 102 98 94 89 83 77 61 ANSI B.5 1 (39.6 m) Boom length Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 24 55 65 75 85 95 105 115 1 1 81.0.6 78.3 76.0 73.8 71.4 69.1 66.7 64.3 61.8 59.3 56.7 54.0 51.3 48.4.3 42.2 38.8.1 31.1 26.5 21.0 13.6 1 (42.7 m) Boom length 26.8 79.2 77.1 74.9 72.8.7 55 68.5 66.3 65 64.0 61.7 75 59.4 57.0 85 54.5 51.9 95 49.3 46.5 105 43.6.6 115 37.3 33.8 1 29.9 1.5 1.2 1 13.1 55,5 * 55,210 * 47,410 38,4 32,0 27,2 23,6,0 18,5 16,610 14,9 13,5 12,3 11,0 10,3 9,5 8,8 8,1 7,5 7,0 6,5 6, 5,0 134 134 133 132 1 129 127 1 123 117 114 111 107 103 98 93 87 72 63 52 36 49,9 * 144 47,210 143 38,2 142 31,810 141 27,0 139 23,4 138,710 136 18,3 134 16,0 131 14,7 129 13,3 126 12,1 123 11,0 119 10,1 116 9,3 111 8,610 107 7,9 102 7,3 96 6,8 6,3 83 5,8 75 5,4 66 5, 54 4,7 37 2 HC 13
WITH 46HI ANGLE BOOM, 4 SHEAVE TIP 58, lb 3 1 (.7 m) Boom length Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 28 55 65 75 85 95 105 115 1 1 1 1 1 1.7 79.9 77.9 76.0 74.0 72.0.0 67.9 65.9 63.8 61.6 59.4 57.2 54.8 52.5.0 47.5 44.8 42.1 39.1 36.0 32.6 28.9 24.6 19.5 12.7 43,9 * 43,1 * 38,0 31,5 26,8 23,1,4 18,1 16,1 14,5 13,1 11,9 10,8 9,9 9, 8,3 7,7 7,1 6,5 6, 5,6 5,2 4,8 4,510 4,1 3,0 153 153 152 151 1 148 146 144 142 1 137 1 131 128 124 116 111 106 94 86 78 68 56 38 ANSI B.5 1 (48.8 m) Boom length Boom Side Frames From Boom Pt. Radius Angle Extended to Ground (Feet) (Degrees) (Pounds) (Feet) 29 55 65 75 85 95 105 115 1 1 1 1 1 1 155 1.9.5 78.7 76.9 75.0 73.2 71.3 69.4 67.4 65.5 63.5 61.5 59.4 57.3 55.2 53.0.7 48.3.9 43.3.7 37.8 34.8 31.5 27.9 23.8 18.9 12.3 39,5 * 39,3 * 37,8 31,410 26,6 22,9,310 17,9 16,000 14,3 12,9 11,7 10,6 9,7 8,9 8,1 7,5 6,9 6,3 5,0 5,4 5,0 4,6 4,310 3,9 3,6 3,4 3,1 163 163 162 161 1 159 157 155 153 151 149 146 143 1 137 133 129 1 115 104 97 89 57 39 14 HC
CRAWLER CRANE HC NOTES TO LIFTING CAPACITY! Warning This rating chart is invalid if the crane has been modified or altered by use of other than GENUINE AMERICAN PARTS as such modifications or alterations may affect its capacity or safe operation. See American Crane Corporation Service Bulliten #9. Ratings in this chart are in POUNDS and do not exceed the percentage of tipping specified for this crane by ANSI B.5. All ratings require that the crane be standing level on a firm uniformly supporting surface. Do not lift loads in excess of those shown on this chart. Lifting loads in excess of those shown or operation not in accordance with good operating practice, including limitations shown on page 3499 of Operator's Manual, can cause tipping, structural damage or catastrophic failure. Asterisk (*) areas on this chart indicate ratings which are limited by strength of material or factors other than stability (tipping). RADIUS IN FEET is the horizontal distance at ground level from the crane centerline of rotation to a vertical line through the center of gravity of the suspended load. When using the main boom fall with jib in place, the main fall ratings must be reduced by the jib effective weight shown on the jib rating chart plus twice the weight of all suspended blocks, slings, rope, etc., at the jib fall. See Appendix A. When using the main boom fall with boom tip extension in place, the main fall ratings must be reduced by the weight of the boom tip extension plus twice the weight of all suspended blocks, slings, rope, etc., at the boom tip extension fall. See Appendix A. Blocks, slings, buckets and other load carrying devices are considered part of the load. The weight of standard hoisting ropes for the rating at a given radius has been calculated as part of the boom point load and need not be considered in determining net allowable loads. See Appendix A. This chart was developed exclusively for use with a boom only. Under no circumstances are these ratings to be interpreted for use with a jib. Ratings shown on this chart make no allowance for such factors as out of plumb loads, wind, poor soil conditions, improper inflation of rubber tires and dynamic effects due to excessive operating speeds. The user (operator) must exercise judgement to make allowance for these conditions. See page 3499 of Operator's Manual for detailed information. No account is taken of the wind force on the load. This effect, which can be substantial for loads with large surface areas, must be considered by the user. In any wind it is strongly recommended that taglines be used to control the load. 2 BOOM HOIST LINE 14 parts of 5/8 inch diameter EIPS wire rope with a minimum breaking strength of 41,0 pounds. PENDANT SUSPENSION LINE 2 parts of 1-1/4 inch diameter MONOLAY wire rope with a minimum breaking strength of 172,0 pounds. MAIN LOAD LINE 7/8 inch diameter EIPS wire rope with a minimum breaking strength of 79,0 pounds. ERECTION Erection is with the A-Frame fully raised. Erection OVER THE END is with the boom over the idler end. Erection OVER-THE-SIDE is with the boom to the sideframes and with the side frames extended. Blocks, slings and other load carrying devices must be on the ground during erection. HC 15
RANGE DIAGRAM, 47HI BOOM, #9HL JIB 16 HC
CRAWLER CRANE HC WITH 47HI BOOM, #9HL JIB (12.2 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.7 22,5* (.5 m) (33.5 m) (36.6 m) 1 (39.6 m) 58, lb 3 31 33 34 1 78.6 22,5* 76.5 22,1* 79.2,9* 72.2 21,0* 74.9,4* 77.5 19,5* 67.9 19,6.5 19,6 73.0 19,* 63.4 16,0 66.0 16,0 68.4 16,0 58.7 13,4 61.2 13,4 63.6 13,4 53.7 11,4 56.2 11,4 58.4 11,0 48.4 9,9.8 9,9 52.9 9,9.9 22,5* 79.3 22,5* 77.4 22,3* 79.9 21,0* 73.5 21,6* 76.0,5* 78.3 19,6* 69.4 19,4 71.9 19,4 74.2 19,1* 65.3 15,8 67.7 15,8.0 15,8 61.0 13,2 63.4 13,2 65.6 13,2 56.5 11,2 58.9 11,2 61.0 11,2 51.7 9,7 54.1 9,7 56.1 9,7 46.6 8,4 48.9 8,4.8 8,4.7 22,5*.0 22,5* 78.2 22,0*.6 21,1* 74.5 21,8* 76.9,6* 79.1 19,4*.8 19,2 73.1 19,2 75.3 19,2 66.9 15,6 69.2 15,6 71.4 15,6 62.9 13,0 65.2 13,0 67.3 13,0 58.8 11,0 61.1 11,0 63.1 11,0 54.5 9,5 56.7 9,5 58.7 9,5 49.9 8,2 52.1 8,2 53.9 8,2.0 7,2 47.1 7,2 48.8 7,2.9 22,0*.6 22,0* 78.9 22,0* 75.4 22,0* 77.7,1* 79.8 16,4* 71.9 19,0 74.1 19,0 76.2 16,2* 68.3 15,4.5 15,4 72.5 15,4 64.7 12,8 66.8 12,8 68.8 12,8.9 10,0 63.0 10,0 64.9 10,910 56.9 9,3 59.0 9,3.8 9,3 52.7 8, 54.8 8, 56.6 8, 48.3 7,0.4 7,0 52.0 7,0 43.6 6,2.5 6,2 47.1 6,2 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.8,5* 1 (42.7 m) 1 (.7 m) 1 (48.8 m) 36 1 1 37 1 1 1 39 1 1 1 1 ANSI B.5 79.5,210* 76.3 19,2* 78.4 17,0*.4 13,8* 73.0 18,2* 75.1 16,4* 77.0 13,0* 69.6 15,2 71.7 15,2 73.6 13,2* 66.2 12,6 68.2 12,6.1 12,6 62.6 10,0 64.7 10,0 66.5 10,0 59.0 9,1 61.0 9,1 62.7 9,1 55.1 7,8 57.1 7,0 58.8 7,0 51.1 6,8 53.1 6,8 54.7 6,8 46.9 6,010 48.8 6,010.3 6,010 42.3 5,2 44.1 5,2.5 5,2 81.0 17,0*.1 17,1* 77.0 16,0* 79.0 14,4*.9 11,7* 73.9 15,3* 75.9 13,8* 77.7 11,4*.7 14,4* 72.7 13,2* 74.5 11,0* 67.5 12,4 69.4 12,4 71.2 10,5* 64.2 10,0 66.1 10,0 67.8 10,0*.8 8,9 62.7 8,9 64.4 8,9 57.2 7,0 59.1 7,0.7 7,0 53.5 6,6 55.4 6,6 57.0 6,6 49.7 5,810 51.5 5,810 53.0 5,810.5 5,0 47.3 5,0 48.7 5,0 41.1 4,4 42.8 4,4 44.1 4,4.9 14,7*.6 14,6* 77.7 13,0* 79.6 12,2* 74.7 12,9* 76.6 11,7* 78.4 9,6* 71.7 12,1* 73.6 11,* 75.3 9,2* 68.7 11,3*.5 10,4* 72.2 8,0* 65.6 10,310 67.4 9,8* 69.1 8,2* 62.4 8,7 64.2 8,7 65.8 7,810* 59.1 7,510.9 7,510 62.4 7,3* 55.6 6,4 57.4 6,4 58.9 6,4 52.1 5,6 53.8 5,6 55.3 5,6 48.3 4,8.0 4,8 51.4 4,0 44.3 4,2 46.0 4,2 47.3 4,2.0 3,7 41.6 3,7 42.8 3,7 3 HC 17
WITH 47HI BOOM, #9HL JIB (15.2 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.8 21,5* 1 (39.6 m) 1 (42.7 m) 1 (.7 m) 58, lb 3 37 1 38 1 1 1 1 1 79.8 21,5* 76.5 21,210* 79.2 18,3* 73.2 19, 75.9 17,9* 78.3 14,4* 69.9 15,5 72.5 15,5 74.9 14,2* 66.4 12,9 69.0 12,9 71.4 12,9 62.9 10,9 65.5 10,9 67.8 10,9 59.2 9,3 61.8 9,3 64.0 9,3 55.4 8,1 57.9 8,1.1 8,1 51.4 7, 53.8 7, 55.9 7, 47.1 6,2 49.5 6,2 51.5 6,2.9 19,0*.3 19,010* 77.3 18,* 79.8 15,5* 74.2 17,210* 76.6 15,1* 79.0 12,1* 71.0 15,3 73.5 14,5* 75.8 11,9* 67.8 12,7.2 12,7 72.5 11,5* 64.4 10,7 66.9 10,7 69.1 10,7 61.0 9,1 63.4 9,1 65.6 9,1 57.5 7,9 59.9 7,9 62.0 7,9 53.8 6,910 56.1 6,910 58.2 6,910 49.9 6,0 52.2 6,0 54.2 6,0.8 5,310 48.0 5,310 49.9 5,3.8 16,2* 77.9 15,410*.3 13,0* 75.0 14,0* 77.3 12,0* 79.6 10,310* 72.0 13,6* 74.3 12,2* 76.5 10,0* 68.9 12,5 71.3 11,6* 73.4 9,6* 65.8 10,5 68.1 10,5.2 9,2* 62.6 8,9 64.9 8,9 67.0 8,810* 59.3 7,7 61.6 7,7 63.6 7,7 55.9 6,0 58.1 6,0.1 6,0 52.3 5,8 54.5 5,8 56.4 5,8 48.5 5,.7 5, 52.5 5, 44.5 4,4 46.7 4,4 48.4 4,4 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset 81.0 13,810* 1 (48.8 m) 1 (51.8 m) 41 1 1 1 1 43 1 1 1 1 1 ANSI B.5 78.5 13,0*.8 11,3* 75.7 12,2* 78.0 10,8*.1 8,710* 72.9 11,4* 75.1 10,3* 77.2 8,4*.0 10,7* 72.2 9,0* 74.3 8,0* 67.0 10,0* 69.2 9,2* 71.3 7,6* 64.0 8,7 66.2 8,6* 68.2 7,2*.9 7,5 63.1 7,5 65.0 6,8* 57.7 6,510 59.9 6,510 61.8 6,410* 54.4 5,6 56.5 5,6 58.4 5,6.9 4,9 53.0 4,9 54.8 4,9 47.3 4,0 49.3 4,0 51.0 4,0 43.4 3,7.4 3,7 47.0 3,7.9 11,6* 79.0 11,1* 76.4 10,3* 78.5 9,1*.6 7,3* 73.7 9,6* 75.8 8,6* 77.8 7,0*.9 8,9* 73.1 8,1* 75.0 6,6* 68.1 8,0*.3 7,0* 72.2 6,2* 65.3 7,710* 67.4 7,* 69.3 5,8* 62.4 7,* 64.4 6,0* 66.3 5,4* 59.4 6,310 61.4 6,1* 63.2 5,0* 56.3 5,4 58.3 5,4.1 4,6* 53.0 4,7 55.1 4,7 56.8 4,310* 49.7 4, 51.6 4, 53.3 3,9* 46.1 3,5 48.1 3,5 49.6 3,5* 42.3 3,0 44.2 3,0.7 3,0 18 HC
CRAWLER CRANE HC WITH 47HI BOOM, #9HL JIB (18.3 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset 42.9 15,1* 78.7 14,0* 75.9 13,7* 78.7 11,7* 73.1 12,9* 75.8 11,3* 78.3 8,9* 1.2 12,1* 72.9 10,8* 75.4 8,7* (.7 m) 67.3 10,5 69.9 10,3* 72.4 8,4* 64.3 9,010 66.9 9,0 69.3 8,* 61.2 7,7 63.8 7,7 66.1 7,7* 58.0 6,7.6 6,7 62.9 6,7 1 54.6 5,8 57.2 5,8 59.4 5,8 1 51.2 5,1 53.7 5,1 55.9 5,1 1 47.5 4,5.0 4,5 52.1 4,5 1 (48.8 m) 58, lb 3 44 1 1 1 1.8 12,8* 79.3 12,0* 76.6 11,610* 79.2 10,0* 73.9 10,8* 76.5 9,5* 78.9 7,0* 71.1 10,2* 73.7 9,0* 76.1 7,3* 68.4 9,5*.9 8,6* 73.3 7,0* 65.5 8,8 68.0 8,1*.4 6,6* 62.6 7,5 65.1 7,5 67.4 6,310* 59.6 6,5 62.1 6,5 64.3 5,9* 56.5 5,6 58.9 5,6 61.1 5,0* 53.3 4,9 55.7 4,9 57.8 4,9 49.9 4,3 52.3 4,3 54.3 4,3 46.3 3,7 48.7 3,7.6 3,0 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset 81.0 10,9* 1 (51.8 m) 1 1 1 1 1 ANSI B.5 79.7 10,5* 77.2 9,8* 79.7 8,510* 74.6 9,1* 77.1 8,0* 79.4 6,3* 72.0 8,0* 74.5 7,5* 76.8 6,* 69.4 7,8* 71.8 7,1* 74.1 5,7* 66.6 7,0* 69.1 6,6* 71.3 5,4* 63.9 6,7* 66.3 6,210* 68.5 5,0* 61.1 6,2* 63.4 5,7* 65.6 4,7* 58.1 5,4.5 5,3* 62.6 4,3* 55.1 4,7 57.5 4,0 59.5 4,0* 52.0 4,1 54.3 4,1 56.3 3,710* 48.7 3,5 51.0 3,5 52.9 3,3*.2 3, 47.5 3, 49.3 3,0* 3 HC 19
NOTES TO LIFTING CAPACITY! Warning This rating chart is invalid if the crane has been modified or altered by use of other than GENUINE AMERICAN PARTS as such modifications or alterations may affect its capacity or safe operation. See American Crane Corporation Service Bulliten #9. Ratings in this chart are in POUNDS and do not exceed the percentage of tipping specified for this crane by ANSI B.5. All ratings require that the crane be standing level on a firm uniformly supporting surface. Do not lift loads in excess of those shown on this chart. Lifting loads in excess of those shown or operation not in accordance with good operating practice, including limitations shown on page 3499 of Operator's Manual, can cause tipping, structural damage or catastrophic failure. Asterisk (*) areas on this chart indicate ratings which are limited by strength of material or factors other than stability (tipping). RADIUS IN FEET is the horizontal distance at ground level from the crane centerline of rotation to a vertical line through the center of gravity of the suspended load. When using the main boom fall with jib in place, the main fall ratings must be reduced by the jib effective weight shown on the jib rating chart plus twice the weight of all suspended blocks, slings, rope, etc., at the jib fall. See Appendix A. Blocks, slings, buckets and other load carrying devices are considered part of the load. The weight of standard hoisting ropes for the rating at a given radius has been calculated as part of the boom point load and need not be considered in determining net allowable loads. See Appendix A. Ratings shown on this chart make no allowance for such factors as out of plumb loads, wind, poor soil conditions, improper inflation of rubber tires and dynamic effects due to excessive operating speeds. The user (operator) must exercise judgement to make allowance for these conditions. See page 3499 of Operator's Manual for detailed information. No account is taken of the wind force on the load. This effect, which can be substantial for loads with large surface areas, must be considered by the user. In any wind it is strongly recommended that taglines be used to control the load. BOOM HOIST LINE is 14 parts of 5/8 inch diameter EIPS wire rope with a minimum breaking strength of 41,0 pounds. PENDANT SUSPENSION LINE is 2 parts of 1-1/4 inch diameter MONOLAY wire rope with a minimum breaking strength of 172,0 pounds. WHIP LINE is 7/8 inch diameter EIPS wire rope with a minimum breaking strength of 79,0 pounds. ERECTION Erection is with the A-Frame fully raised. Erection OVER THE END is with the boom over the idler end. Erection OVER THE SIDE is with the boom to the sideframes and with the side frames extended. Blocks, slings and other load carrying devices must be on the ground during erection. Note: The #9HL jib mounted on a 47HI outer requires the use of a 47HI / #9HL jib adaptor. Refer to the HC Operators Manual for additional information. HC
CRAWLER CRANE HC RANGE DIAGRAM, 46HI BOOM, #9 ANGLE JIB HC 21
WITH 46HI BOOM, #9 ANGLE JIB (6.1 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.7 18,2* (15.2 m) (18.3 m) (21.3 m) (24.4 m) (27.4 m) (.5 m) 58, lb 3 17 19 22 23 78.2 18,2*.9 18,2* 74.1 18,2* 76.7 18,2* 79.2 18,2* 69.8 18,2* 72.5 18,2* 74.9 18,2* 65.5 18,2* 68.1 18,2*.5 18,2*.9 18,2* 63.5 18,2* 65.8 18,2* 51.1 18,2* 53.6 18,2* 55.7 18,2*.4 18,2* 79.7 18,2* 76.1 18,2* 78.4 18,2*.6 18,2* 72.4 18,2* 74.7 18,2* 76.9 18,2* 68.7 18,2* 71.0 18,2* 73.1 18,2* 64.8 18,2* 67.1 18,2* 69.1 18,2* 56.7 18,2* 58.9 18,2*.8 18,2* 47.6 18,2* 49.7 18,2* 51.5 18,2*.8 18,2* 77.6 18,2* 79.7 18,2* 74.4 18,2* 76.5 18,2* 78.4 18,2* 71.1 18,2* 73.2 18,2* 75.1 18,2* 67.7 18,2* 69.8 18,2* 71.6 18,2*.7 18,2* 62.7 18,2* 64.5 18,2* 53.2 18,2* 55.1 18,2* 56.8 18,2* 44.7 16,0 46.6 16,0 48.1 16,0.6 18,2* 78.9 18,2*.8 18,2* 76.0 18,2* 77.8 18,2* 79.6 18,2* 73.0 18,2* 74.9 18,2* 76.6 18,2*.0 18,2* 71.9 18,2* 73.6 18,000* 63.9 18,2* 65.7 18,2* 67.3 18,2* 57.3 18,2* 59.1 18,2*.6 18,2*.3 15,8 52.0 15,8 53.4 15,8 42.3 13,2 44.0 13,2.2 13,2.9 18,2* 79.9 18,2* 77.2 18,2* 79.0 18,2*.6 18,2* 74.6 18,2* 76.3 18,2* 77.9 18,2* 71.9 18,2* 73.6 18,2* 75.1 18,2* 66.4 18,2* 68.0 18,2* 69.5 18,2*.6 18,2* 62.2 18,2* 63.6 18,2* 54.5 15,5 56.0 15,5 57.4 15,5 47.8 12,9 49.3 12,9.6 12,9.3 11,000 41.7 11,000 42.8 11,000.7 18,2* 78.3 18,2* 79.9 18,2* 75.9 18,2* 77.5 18,2* 78.9 18,2* 73.4 18,2* 75.0 18,2* 76.4 18,2* 68.4 18,2*.0 18,2* 71.3 18,2* 63.2 18,2* 64.7 18,2* 66.1 18,2* 57.8 15,3 59.3 15,3.5 15,3 52.0 12,7 53.4 12,7 54.6 12,7.6 10,7 47.0 10,7 48.1 10,7 38.5 9,2 39.8 9,2.7 9,2 (36.6 m) 1 (39.6 m) 1 (42.7 m) 28 1 31 1 1 ANSI B.5 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset 81.0 18,2* (33.5 m) 26 79.2 18,2*.7 18,2* 77.0 18,2* 78.4 18,2* 79.8 18,2* 74.7 18,2* 76.2 18,2* 77.5 18,2*.2 18,2* 71.6 18,2* 72.9 18,2* 65.4 18,2* 66.8 18,2* 68.1 18,2*.5 15, 61.9 15, 63.1 15, 55.3 12,0 56.7 12,0 57.8 12,0 49.8 10,5 51.1 10,5 52.2 10,5 43.7 8,9.0 8,9 46.0 8,9 36.9 7,7 38.1 7,7 38.9 7,7.8 18,2*.0 18,2* 77.9 18,2* 79.3 18,2*.5 18,2* 75.8 18,2* 77.2 18,2* 78.4 18,2* 71.6 18,2* 72.9 18,2* 74.1 18,2* 67.3 18,2* 68.6 18,2* 69.7 18,2* 62.8 14,8 64.1 14,8 65.2 14,0 58.1 12,2 59.4 12,2.4 12,2 53.2 10,310 54.4 10,310 55.4 10,310 47.9 8,7 49.1 8,7.0 8,7 42.1 7,510 43.2 7,510 44.1 7,510.5 6,4 36.6 6,4 37.3 6,4.7 18,2* 78.7 18,2*.0 18,2* 76.8 18,2* 78.0 18,2* 79.2 18,2* 72.9 18,2* 74.1 18,2* 75.2 18,2* 68.9 18,2*.1 18,2* 71.2 18,2* 64.7 14,6 65.9 14,6 67.0 14,6.4 12,0 61.6 12,0 62.7 12,0 56.0 10,0 57.1 10,0 58.1 10,0 51.2 8,5 52.4 8,5 53.3 8,5 46.1 7,2 47.3 7,2 48.1 7,2.6 6,2 41.6 6,2 42.4 6,2 34.3 5,3.3 5,3.9 5,3.9 18,2* 79.4 18,2*.6 18,2* 77.6 18,2* 78.8 18,2* 79.9 18,2* 74.0 18,2* 75.1 18,2* 76.2 18,2*.2 18,0 71.4 18,0 72.4 18,0 66.4 14,4 67.5 14,4 68.5 14,4 62.4 11,8 63.6 11,8 64.5 11,8 58.3 9,8 59.4 9,8.4 9,8 54.0 8,2 55.1 8,2 56.0 8,2 49.5 7,0.6 7,0 51.4 7,0 44.6 6,000.6 6,000 46.4 6,010 39.2 5,1.2 5,1.9 5,1 33.1 4,4 34.1 4,4 34.6 4,4 22 HC
CRAWLER CRANE HC WITH 46HI BOOM, #9 ANGLE JIB 58, lb 3 (6.1 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.7 18,2* 1 (.7 m) 33 1 1 1.1 18,2* 78.4 18,2* 79.5 18,2*.5 18,2* 74.9 18,2* 76.0 18,2* 77.0 18,2* 71.4 17,7 72.5 17,7 73.5 17,7 67.8 14,0 68.9 14,0 69.9 14,0 64.2 11,5 65.2 11,5 66.2 11,5.4 9,0 61.4 9,0 62.3 9,0 56.4 8,0 57.5 8,0 58.3 8,0 52.3 6,7 53.3 6,7 54.1 6,7 47.9 5,7 48.9 5,7 49.7 5,7 43.2 4,0 44.2 4,0 44.9 4,0 38.0 4,1 38.9 4,1 39.6 4,1 32.1 3,5 33.0 3,5 33.5 3,5 ANSI B.5 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.9 18,2* 1 (48.8 m) 34 1 1 1 1.6 18,2* 79.0 18,2*.1 18,2* 75.8 18,2* 76.8 18,2* 77.8 16,5* 72.5 17,5 73.5 17,5 74.5 15,7* 69.1 13,9.2 13,9 71.1 13,9 65.7 11,3 66.7 11,3 67.6 11,3 62.2 9,3 63.2 9,0 64.0 9,0 58.5 7,8 59.5 7,8.3 7,8 54.7 6,5 55.7 6,5 56.5 6,5.7 5,5 51.7 5,5 52.4 5,5 46.5 4,6 47.4 4,6 48.1 4,6 41.9 3,9 42.8 3,9 43.5 3,9 36.9 3,3 37.8 3,3 38.3 3,3 31.2 2,7 32.0 2,7 32.4 2,7 (9.1 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.8 18,2* (24.4 m) (27.4 m) (.5 m) 24 26 27.3 18,2* 77.7 18,2*.3 18,2* 75.0 18,2* 77.6 18,2*.0 18,2* 72.3 18,2* 74.9 18,2* 77.3 18,2* 66.8 18,2* 69.3 18,2* 71.6 18,2* 61.0 18,2* 63.5 18,2* 65.7 18,2* 54.9 15,910 57.3 15,9 59.4 15,9 48.2 13,3.6 13,3 52.5 13,3.6 18,2* 78.7 18,2* 76.3 18,2* 78.7 18,2*.9 18,2* 73.8 18,2* 76.2 18,2* 78.4 18,2* 68.8 18,2* 71.2 18,2* 73.3 18,2* 63.6 18,2* 65.9 18,2* 68.0 18,2* 58.2 15,6.4 15,6 62.4 15,6 52.4 13,0 54.6 13,0 56.4 13,0 46.0 11,0 48.1 11,0 49.9 11,0.9 18,2* 79.6 18,2* 77.4 18,2* 79.5 18,2* 75.1 18,2* 77.3 18,2* 79.3 18,2*.5 18,2* 72.7 18,2* 74.7 18,2* 65.8 18,2* 67.9 18,2* 69.8 18,2*.9 15,4 63.0 15,4 64.8 15,4 55.7 12,8 57.7 12,8 59.5 12,8.2 10,8 52.2 10,8 53.8 10,8 44.1 9,2 46.0 9,0 47.6 9,0 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.7 18,2* (33.5 m) (36.6 m) 1 (39.6 m) 29 32 1.3 18,2* 78.3 18,2*.3 18,2* 76.2 18,2* 78.2 18,2*.1 18,2* 72.0 18,2* 74.0 18,2* 75.8 18,2* 67.6 18,2* 69.6 18,2* 71.4 18,2* 63.1 15,1 65.1 15,1 66.8 15,1 58.4 12,5.4 12,5 62.0 12,5 53.5 10,5 55.4 10,5 57.0 10, 48.2 9,0.0 9,0 51.5 9,0 42.4 7,7 44.2 7,7.6 7,7 81.0 18,2* 79.1 18,2* 81.0 18,2* 77.1 18,2* 79.0 18,2*.8 18,2* 73.2 18,2* 75.1 18,2* 76.8 18,2* 69.2 18,2* 71.0 18,2* 72.7 18,2* 65.0 14,9 66.9 14,9 68.5 14,9.8 12,3 62.6 12,3 64.2 12,3 56.3 10,3 58.1 10,3 59.6 10,3 51.5 8,8 53.3 8,8 54.7 8,8 46.5 7,5 48.2 7,5 49.5 7,5.9 6,5 42.5 6,5 43.8 6,5.8 18,2* 79.7 18,2* 77.9 18,2* 79.7 18,2* 74.3 18,2* 76.0 18,2* 77.7 18,2*.5 18,2* 72.3 18,2* 73.9 18,2* 66.7 14,7 68.4 14,7.0 14,7 62.7 12, 64.4 12, 66.0 12, 58.6 10,1.3 10,1 61.8 10,1 54.3 8,5 56.0 8,5 57.4 8,5 49.8 7,3 51.4 7,3 52.7 7,3 44.9 6,0 46.5 6,0 47.7 6,310 39.5 5,4 41.0 5,4 42.2 5,4 3 HC 23
WITH 46HI BOOM, #9 ANGLE JIB (9.1 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.7 18,2* 1 (42.7 m) 58, lb 3 34 1 1.3 18,2* 78.6 18,2*.3 18,2* 75.2 18,2* 76.9 18,2* 78.4 18,2* 71.7 18,0 73.4 18,0 74.9 18,0 68.1 14,0 69.8 14,0 71.2 14,0 64.5 11,8 66.1 11,8 67.5 11,8.7 9,0 62.3 9,0 63.7 9,0 56.7 8,3 58.3 8,3 59.6 8,3 52.6 7,0 54.1 7,0 55.4 7,0 48.2 6,0 49.7 6,0.9 6,0 43.5 5,210 44.9 5,210 46.1 5,210 38.3 4,4 39.7 4,4.7 4,4 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.8 18,2* 1 (48.8 m) 37 1 1 1 1 ANSI B.5 79.8 18,2* 76.8 18,2* 78.3 17,8* 79.7 14,9* 73.7 17,6 75.2 17,0* 76.5 14,4*.5 14,0 72.0 14,0 73.3 13,7* 67.3 11,4 68.8 11,4.1 11,4 64.0 9,4 65.4 9,4 66.7 9,4.6 7,8 62.0 7,8 63.3 7,8 57.1 6,6 58.5 6,6 59.7 6,6 53.4 5,0 54.8 5,0 55.9 5,0 49.5 4,7.9 4,7 52.0 4,7.4 4,010 46.7 4,010 47.8 4,010 41.0 3,3 42.3 3,3 43.2 3,3 36.1 2,8 37.3 2,8 38.2 2,8 1 (.7 m) 1 1 1.9 18,2* 79.3 18,2*.9 18,2* 76.0 18,2* 77.6 18,2* 79.1 17,4* 72.8 17,8 74.3 17,8 75.7 16,9* 69.4 14,2.9 14,2 72.3 14,2 66.0 11,6 67.5 11,6 68.9 11,6 62.4 9,6 63.9 9,6 65.3 9,6 58.8 8,.3 8, 61.6 8, 55.0 6,8 56.5 6,8 57.7 6,8 51.0 5,810 52.4 5,810 53.6 5,8 46.8 4,9 48.2 4,9 49.3 4,9 42.2 4,2 43.5 4,2 44.6 4,2 37.2 3,0 38.5 3,0 39.4 3,0 (12.2 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.7 18,2* 78.6 18,2* 76.5 18,2* 79.3 18,2* 72.3 18,2* 75.0 17,7* 77.5 16,310* 68.0 18,2*.6 16,8* 73.1 15,6* (.5 m) 63.5 15,4 66.1 15,4 68.5 15,0* 58.8 12,8 61.4 12,8 63.7 12,8 53.9 10,0 56.4 10,0 58.6 10,910 48.6 9,3 51.0 9,3 53.1 9,3 (33.5 m) 31.9 18,2* 79.4 18,2* 77.4 18,2*.0 18,2* 73.5 18,2* 76.0 17,9* 78.4 16,410* 69.5 18,2* 72.0 17,0* 74.3 15,7* 65.4 15,2 67.8 15,2.1 15,0* 61.1 12,6 63.5 12,6 65.7 12,6 56.6 10,6 59.0 10,6 61.1 10,6 51.9 9,0 54.2 9,0 56.2 9,0 46.8 7,8 49.1 7,8 51.0 7,8 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.8 18,2* (36.6 m) 1 (39.6 m) 33 34 1.1 18,2* 78.2 18,2*.6 18,2* 74.6 18,2* 76.9 18,2* 79.1 16,5*.8 18,2* 73.2 17,310* 75.3 15,8* 67.0 15,0 69.3 15,0 71.4 15,0 63.1 12,410 65.3 12,410 67.4 12,410 58.9 10,4 61.2 10,4 63.2 10,4 54.6 8,8 56.9 8,8 58.8 8,8.1 7,6 52.3 7,6 54.1 7,6.2 6,5 47.3 6,5 49.0 6,0 81.0 18,2*.6 18,2* 78.9 18,2* 75.5 18,2* 77.7 18,2* 79.8 16,6* 72.0 18,2* 74.2 17,5* 76.3 16,0* 68.4 14,7.6 14,7 72.6 14,7 64.8 12,1 66.9 12,1 68.9 12,1 61.0 10,1 63.1 10,1 65.0 10,1 57.0 8,6 59.1 8,6 61.0 8,6 52.9 7,3 54.9 7,3 56.7 7,3 48.5 6,3.5 6,3 52.2 6,3 43.8 5,4.7 5,4 47.3 5,4 24 HC
CRAWLER CRANE HC WITH 46HI BOOM, #9 ANGLE JIB (12.2 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.8 18,2* 79.6 18,2* 76.3 18,2* 78.4 18,2*.4 16,7* 73.0 18,1 75.1 17,7* 77.1 16,1* 1 (42.7 m) 1 (.7 m) 58, lb 3 36 1 1 38 1 1 1 69.7 14,5 71.7 14,5 73.6 14,5 66.2 11,9 68.3 11,9.1 11,9 62.7 9,9 64.7 9,9 66.5 9,9 59.1 8,3 61.1 8,3 62.8 8,0 55.3 7,1 57.2 7,1 58.9 7,1 51.3 6, 53.2 6, 54.8 6, 47.0 5,2 48.9 5,2.5 5,2 42.5 4,510 44.3 4,510.7 4,5.7 18,2*.1 18,2* 77.0 18,2* 79.0 18,2*.9 15,4* 73.9 17,0 75.9 17,0* 77.8 15,1*.8 14,310 72.7 14,310 74.6 14,310 67.6 11,6 69.5 11,6 71.3 11,0 64.3 9,710 66.2 9,710 67.9 9,710.9 8,1 62.8 8,1 64.4 8,1 57.3 6,8 59.2 6,8.8 6,8 53.7 5,8 55.5 5,8 57.1 5,8 49.8 5,000 51.6 5,000 53.1 5,000.7 4,2 47.5 4,2 48.9 4,2 41.3 3,6 43.0 3,6 44.3 3,6 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.9 18,2* 1 (48.8 m) 39 1 1 1 1 ANSI B.5.6 18,2* 77.7 18,2* 79.6 16,4* 74.8 17,4* 76.6 15,7* 78.4 12,9* 71.8 14,0 73.6 14,0 75.4 12,510* 68.7 11,4.6 11,4 72.3 11,4 65.6 9,4 67.5 9,4 69.1 9,4 62.4 7,9 64.3 7,9 65.9 7,9 59.2 6,6 61.0 6,6 62.5 6,6 55.7 5,6 57.5 5,6 59.0 5,6 52.2 4,7 53.9 4,7 55.4 4,7 48.4 4,0.2 4,0 51.6 4,0 44.5 3,410 46.1 3,4 47.5 3,4.2 2,8 41.8 2,8 43.0 2,8 3 (15.2 m) Jib length Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset 37.8 18,2* 79.8 18,0* 76.6 16,9* 79.2 14,7* 73.3 15,8* 75.9 13,9* 78.4 12,5* 1 69.9 14,810 72.5 13,2* 75.0 12,0* (39.6 m) 66.5 12,0 69.1 12,0 71.5 11,6* 63.0 10,210 65.5 10,2 67.8 10,2 59.3 8,6 61.9 8,6 64.1 8,6 55.5 7,0 58.0 7,0.2 7,410 51.5 6,3 54.0 6,3 56.1 6,3 1 47.3 5,510 49.7 5,510 51.7 5,510 Jib 5.0 Deg offset 15.0 Deg offset.0 Deg offset.9 18,2* 1 (.7 m) 1 1 1 77.9 17,4*.3 14,9* 75.0 16,3* 77.4 14,2* 79.6 12,7* 72.0 14,3 74.4 13,5* 76.6 12,2* 69.0 11,7 71.3 11,7 73.5 11,7 65.9 9,7 68.2 9,7.3 9,7 62.7 8,1 65.0 8,1 67.0 8,1 59.4 6,9 61.7 6,9 63.7 6,9 56.0 5,8 58.2 5,8.2 5,8 52.4 5,0 54.6 5,0 56.5 5,0 48.7 4,2.8 4,2 52.7 4,0 44.7 3,6 46.8 3,6 48.5 3,6 1 (42.7 m) 38 1 1 81.0 18,2*.4 18,2* 77.3 17,1* 79.8 14,8* 74.2 16,* 76.7 14,* 79.0 12,6* 71.0 14,5 73.5 13,4* 75.8 12,1* 67.8 11,9.3 11,9 72.5 11,7* 64.5 9,9 66.9 9,9 69.1 9,9 61.1 8,4 63.5 8,4 65.7 8,4 57.6 7,1.0 7,1 62.0 7,1 53.9 6,1 56.3 6,1 58.3 6,1.1 5,2 52.3 5,2 54.3 5,2.9 4,5 48.2 4,5.0 4,5 1 (48.8 m) 42 1 1 1 1.7 18,2* 78.5 17,4*.8 14,9* 75.7 16,0* 78.0 14,3*.1 11,5* 72.9 14, 75.1 13,7* 77.2 11,2*.0 11,0 72.3 11,0 74.3 10,8* 67.1 9,510 69.3 9,510 71.3 9,510 64.1 7,9 66.3 7,9 68.3 7,9 61.0 6,6 63.2 6,6 65.1 6,0 57.8 5,6.0 5,6 61.8 5,6 54.5 4,0 56.6 4,0 58.5 4,810 51.1 4,0 53.1 4,0 54.9 4,0 47.4 3,4 49.5 3,4 51.2 3,4 43.5 2,8.5 2,8 47.1 2,0 HC
NOTES TO LIFTING CAPACITY! Warning This rating chart is invalid if the crane has been modified or altered by use of other than GENUINE AMERICAN PARTS as such modifications or alterations may affect its capacity or safe operation. See American Crane Corporation Service Bulliten #9. Ratings in this chart are in POUNDS and do not exceed the percentage of tipping specified for this crane by ANSI B.5. All ratings require that the crane be standing level on a firm uniformly supporting surface. Do not lift loads in excess of those shown on this chart. Lifting loads in excess of those shown or operation not in accordance with good operating practice, including limitations shown on page 3499 of Operator's Manual, can cause tipping, structural damage or catastrophic failure. Asterisk (*) areas on this chart indicate ratings which are limited by strength of material or factors other than stability (tipping). RADIUS IN FEET is the horizontal distance at ground level from the crane centerline of rotation to a vertical line through the center of gravity of the suspended load. When using the main boom fall with jib in place, the main fall ratings must be reduced by the jib effective weight shown on the jib rating chart plus twice the weight of all suspended blocks, slings, rope, etc., at the jib fall. See Appendix A. Blocks, slings, buckets and other load carrying devices are considered part of the load. The weight of standard hoisting ropes for the rating at a given radius has been calculated as part of the boom point load and need not be considered in determining net allowable loads. See Appendix A. Ratings shown on this chart make no allowance for such factors as out of plumb loads, wind, poor soil conditions, improper inflation of rubber tires and dynamic effects due to excessive operating speeds. The user (operator) must exercise judgement to make allowance for these conditions. See page 3499 of Operator's Manual for detailed information. No account is taken of the wind force on the load. This effect, which can be substantial for loads with large surface areas, must be considered by the user. In any wind it is strongly recommended that taglines be used to control the load. The weight of all suspended blocks, slings, or other load carrying devices including those at the main fall, are considered part of the jib load. The weight of standard hoisting ropes for the rating at a given radius has been calculated as part of the jib point dead load and need not be considered in determining net allowable loads. See Appendix A. BOOM HOIST LINE 14 parts of 5/8 inch diameter EIPS wire rope with a minimum breaking strength of 41,0 pounds. PENDANT SUSPENSION LINE 2 parts of 1-1/4 inch diameter MONOLAY wire rope with a minimum breaking strength of 172,0 pounds. WHIP LINE 7/8 inch diameter IPS wire rope with a minimum breaking strength of 69,0 pounds. JIB FRONTSTAY & BACKSTAY PENDANTS 7/8 inch diameter IPS wire rope with a minimum breaking strength of 69,0 pounds. ERECTION Erection is with the A-Frame fully raised. Erection OVER-THE-END is with the boom over the idler end. Erection OVER-THE-SIDE is with the boom to the sideframes and with the side frames extended. Blocks, slings and other load carrying devices must be on the ground during erection. Note: The #9 jib mounted on a 46HI outer requires the use of a 46HI #9 jib adaptor. Refer to the HC Operator s Manual for additional information. 26 HC
CRAWLER CRANE HC NOTES HC 27
TECHNICAL DESCRIPTION HYDRAULIC CRAWLER CRANE Maximum lifting capacity tons (73 mt). Boom systems 47 HI Boom with Offset Tip 0 ft (61 m) maximum boom length. 2 ft ( m) maximum boom and jib combination length. 47 HI Tubular chord boom, pin connected. ft inner and ft outer and 10 ft / ft / ft available inserts provide boom compositions in 10 ft increments from ft to 0 ft. 46 HR Angle Boom with 4 Sheave Tip 1 ft maximum boom length. 0 ft (61 m) maximum boom and jib combination length. 46 HR Angle Boom, pin connected. ft inner and ft outer and 10 ft / ft / ft available inserts provide boom compositions in 10 ft increments from ft to 1 ft. Robust engine Cummins Model QSB 5.9 Turbocharged After Cooled diesel engine, 4 cycle, 6 cylinders, 9 cubic inch displacement, 5.9 liters, 185 BHP @20 rpm, gallons fuel tank capacity. Environmental operator s cab Designed to provide excellent viewing range and quiet, comfortable operation. 37 inch (0.91 m) wide cab has wide curve windows on both top and bottom. Easy-to-operate modular and ergonomically designed controls reduce operator fatigue and increase productivity. Load Moment Indicator with interactive screen features as shockless stop system. Operator can select from three display modes: loaded condition diagram, rated lifting curve or rated lifting load table. Adjustable operator s seat, radio, air conditioner, overhead window, sun visor, fan, overhead and front wipers and drum rotation indicators are standard. Heavy duty carbody and crawlers Fabricated steel carbody is deep box constructed with square axles for the crawler side frames. Precision machined top supports anti-friction swing circle and multiple pass hydraulic swivel joint. Crawlers have high alloy steel tumbler yokes and rigid fabricated structures with sealed rollers. 36 (914 mm) crawler shoes. Travel mechanism is set within shoe width. Side frames extended or retracted by cylinders inside the carbody. Two travel speed settings 0.8 / 1.24 mph (1.3 / 2.0 km/h). % (22 ) gradeability. Powerful, high-speed hoist system Identical inline, independent main and auxiliary load hoisting drums are grooved for 7/8 in. (22.4 mm) diameter rope. Line speed is 5 fpm (162 m /min.), line pull is 32,0 lb (14 697 kg). Each drum, including optional third, has power up/down and freefall. Load hoists are further controllable in stepless mode. Ample work space in front of the drums allows easy access for cable installation and maintenance. Internal expanding band clutch. 3.3 rpm swing speed. High capacity, dependable hydraulic system Open circuit system has 2 variable displacement piston pumps with system capacity of 116 gpm (4 lpm). Hydraulic reservoir with 79 gallons (0 l) capacity and 10 micron filtration. Component working range is between -4 and 3 F (- and 95 C). Flip up doors provide easy access to engine and hydraulic components for service. Three piece removable counterweight Three piece pin connected counterweight can be assembled or disassembled easily within minutes. Hydraulic counterweight removal system is standard and utilizes the A frame and crane auxiliary drum to make the HC one of the most transportable cranes in its class. Moves on three trucks with full boom and #9HL jib. Carbody sideframes and boom weigh in at under 88,000 lb (39 917 kg). At 11 ft 9.75 in. (3.6 m) wide and 10 ft 2 in. (3.09 m) high, the HC at working weight will transport on a standard lowboy trailer. Options include Third drum Luffing jib attachment Automotive type lights 46HI angle boom Hydraulic power take off Single sheave extension Jib and jib inserts 28 HC
CRAWLER CRANE HC TRANSPORT EXAMPLE FOR HC 1 47HI BOOM AND #9HL JIB Loads based on 48 ft flatbed trailer. Loading information is an example only, specific loads will vary depending on crane options. Weights shown do NOT include blocking or tie-down material. LOAD NO. 1 3 x 47 H Boom Center Sections @ 2,0 # each................................................................... 6,1 lbs Inside Counterwieght......................................................................................... 16,000 lbs #9HL Jib Center.......................................................................................... 385 lbs Center Counterweight......................................................................................... 21,000 lbs 1 x 47 H 10 Boom Center Sections............................................................................... 0 lbs TOTAL LOAD................................................................................................ 44,2 lbs LOAD NO. 2 Outside Counterweight........................................................................................ 21,000 lbs 47HI Boom Outer............................................................................................. 2,2 lbs 47 H Boom Center......................................................................................... 2,0 lbs #9HL Jib Inner.............................................................................................. 8 lbs #9HL Jib Outer.............................................................................................. 665 lbs Crate, Misc. Parts, Block & Ball.................................................................................. 3,0 lbs TOTAL LOAD................................................................................................,3 lbs LOAD NO. 3 Basic Upper, including: a) Carbody b) Sideframes c) Boom Inner TOTAL LOAD (BASIC CRANE, etc.)............................................................................... 88,000 lbs 5 KEY Counterweight CB Central ballast HC 29
CRAWLER CRANE HC The information contained in this brochure merely consists of general descriptions and a broad compilation of performance features which might not apply precisely as described under specific application conditions or which may change as a result of further product development. The desired performance features only become binding once expressly agreed in the final contract. Note: Data published herein is intended as a guide only and shall not be construed to warrant applicability for lifting purposes. Crane operation is subject to the computer charts and operation manual both supplied with the crane. Subject to change without notice. 03 / 06 Terex Cranes Wilmington Operations Mobile hydraulic and lattice-boom cranes 2 Raleigh St. Wilmington, NC 28412 USA Phone +1 910 395 Fax +1 910 395 8538 Email: american@american-crane.com