Mobile Standard Construction and HEX-COR augers have been tested in the field and independently tested in the laboratory and are proven to be equal to or stronger than any other auger in the industry. All Mobile continuous flight augers are manufactured through the use of an automatic inert gas metal arc welding process to assure consistent high quality and maximum strength. Flights are formed with a slightly tapered concave surface designed to throw cuttings toward the shaft, minimizing clogging and auger drag. Timed flight pitch is set at an optimum angle to produce the best conveyance of material for general auger exploration work and to maintain continuity of the flight spiral from one section to the next. REPLACEABLE HEX SHANK (SECTION ) REMOVABLE GROOVE PIN (SECTION ) HEX-COR AUGER (SECTION ) Uniform bead hardfacing, standard on HEX-COR augers and optional on Standard Construction, ensures flight edges have sufficient chromemanganese alloy for non-brittle toughness and greater resistance to abrasion. Standard Construction augers are manufactured by conventional methods with the exception of the continuous flighting which is welded on both sides to the center shaft by an exclusive manufacturing process. The center shafts of Standard Construction augers are formed of high quality, low carbon steel tubing to provide minimum weight with maximum strength and rigidity. Innovative HEX-COR augers have many advantages over Standard Construction augers. In addition to superior strength, they have no shank/socket bulge to impede cutting conveyance and come with full length, flight-edge hardfacing standard. They are completely interchangeable with other augers of common shank and socket size, use all auger heads of matching shank design, and are easily repaired in the field. CONTINUOUS FLIGHT ON BOTH STANDARD CONSTRUCTION AND HEX-COR AUGERS U-PIN (SECTION ) The flighting and the center shaft, made of the highest quality steels, are welded into one unit utilizing inert gas metal arc welding. The center shaft tube of HEX-COR augers is hex-pierced to the hex shank size throughout its length so that shanks simply slip into the center shaft. This design allows for fast replacement of worn or broken shanks in the field. BULLDOG HEAD (SECTION ) - 205 Mobile Drill, LLC. All rights reserved.
hex-cor tm augers Don t replace the entire auger, just the shank HEX-COR TM exclusively from Mobile. Length D Available in hole sizes 2-/2" (64mm) through 2" (305mm) Hex sized 3/6", -/8", -5/8", 2 " (20.6mm, 29mm, 4mm and 5mm) Field Replacement Shank Internal Hex Tubing Hardfaced Flight Edges U-Pin Furnished with Each Section P D DIAMETER P PITCH STOCK LENGTH HOLE SIZE HEX CONN. Flight PART NUMBER in mm in mm in mm in mm ft m lb kg 2-/2" 64 2-3/8.60 2 5 3/6 2 2.5.9 2 5.4 5/6" 0065 2-/2" 64 2-3/8.60 2 5 3/6 2 4.22 5 0 5/6" 0067-0 2-/2" 64 2-3/8.60 2 5 3/6 2 5.5 8 8.2 5/6" 0067 3 76 2-5/8.67 2 5 3/6 2 3.9 4 6.4 5/6" 0068 3 76 2-5/8.67 2 5 3/6 2 5.5 22 0 5/6" 0070 3-/2 89 3-/4.83 3-/3 85 3/6" 2 3.9 5/6" 0069 2-3/4" 0 0 0 0 0 -/8" 29 5.5 0 0 5/6" 078 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 2.76 5/6" 0073-03 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 2.5.22 5/6" 0073-02 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 3.9 8 8.2 5/6" 007 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 4.22 5/6" 0097 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 5.5 30 3.6 5/6" 0073 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 5.5 /2" 0073-0 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 7 2.3 5/6" 00483 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 7 2.3 5/6" 007272 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 0 3 6 27.7 5/6" 0048 4-/2" 4 4 02 3-/3 85 -/8" 29 2.6 5/6" 0098 4-/2" 4 4 02 3-/3 85 -/8" 29 2.5.76 5/6" 0074-0 4-/2" 4 4 02 3-/3 85 -/8" 29 3.9 22 0 5/6" 0074 4-/2" 4 4 02 3-/3 85 -/8" 29 3.9 5/6" 0074-03 4-/2" 4 4 02 3-/3 85 -/8" 29 5.5 34 5.4 5/6" 0076 4-/2" 4 4 02 3-/3 85 -/8" 29 0 3 70 3.8 5/6" 00482 5" 27 4-/2 4 4 02 -/8" 29 3.9 27 2.2 5/6" 0077 5" 27 4-/2 4 4 02 -/8" 29 5.5 36 6.3 5/6" 0079 6" 52 5-/2 40 5 85 -/8" 29 3.9 26.8 5/6" 0080 6" 52 5-/2 40 5 27 -/8" 29 4.22 5/6" 008 6" 52 5-/2 40 5 27 -/8" 29 5.5 40 8. 5/6" 0082 7" 78 6 78 5 27 -/8" 29 5.5 5/6" 0087 SERIES 25 500-2 Special sizes available upon request based on minimum order quantities. 205 Mobile Drill, LLC. All rights reserved. Key: * Designates weights less than lb (.5kg) Consult Factory
hex-cor tm augers Don t replace the entire auger, just the shank HEX-COR TM exclusively from Mobile. Length D Available in hole sizes 2-/2" (64mm) through 2" (305mm) Hex sized 3/6", -/8", -5/8", 2 " (20.6mm, 29mm, 4mm and 5mm) Field Replacement Shank Internal Hex Tubing Hardfaced Flight Edges U-Pin Furnished with Each Section P D DIAMETER P PITCH STOCK LENGTH HOLE SIZE HEX CONN. Flight PART NUMBER in mm in mm in mm in mm ft m lb kg 4-/2" 4 4 02 3-/3 85-5/8" 4 2.6 5/6" 950334 4-/2" 4 4 02 3-/3 85-5/8" 4 2.5.76 5/6" 0083 4-/2" 4 4 02 3-/3 85-5/8" 4 3.9 5/6" 007208 4-/2" 4 4 02 3-/3 85-5/8" 4 3.9 5/6" 007208-0 4-/2" 4 4 02 3-/3 85-5/8" 4 4.22 5/6" 0084 4-/2" 4 4 02 3-/3 85-5/8" 4 5.5 54 24.5 5/6" 0085 4-/2" 4 4 02 3-/3 85-5/8" 4 0 3 04 47.2 5/6" 0086 5" 27 4-/2 4 4 85-5/8" 4 5.5 54 24.5 5/6" 0089 5" 27 4-/2 4 4 85-5/8" 4 5.5 5/6" 0089-0 6" 52 5-/2 40 5 85-5/8" 4 3.9 5/6" 00758 6" 52 5-/2 40 5 85-5/8" 4 2.6 5/6" 009-02 6" 52 5-/2 40 5 85-5/8" 4 3.9 5/6" 00758-0 6" 52 5-/2 40 5 85-5/8" 4 4.22 5/6" 0099 6" 52 5-/2 40 5 85-5/8" 4 5.5 58 26.3 5/6" 009 6" 52 5-/2 40 5 85-5/8" 4 5.5 3/8" 009-38 6" 52 5-/2 40 5 85-5/8" 4 9.8 3 5/6" 50259-07 6" 52 5-/2 40 5 85-5/8" 4 0 3 5/6" 0092 7" 78 6 52 5 85-5/8" 4 5.5 64 29 5/6" 0093 8" 203 7 78 7 78-5/8" 4 3.9 5/6" 50259-04 8" 203 7 78 7 78-5/8" 4 4.22 5/6" 50259-05 8" 203 7 78 7 78-5/8" 4 5.5 72 32.7 5/6" 0095 8" 203 7 78 7 78-5/8" 4 0 3 39 63 5/6" 0096 0" 203 8.5 225 7 78-5/8" 4 4.22 5/6" 007240-04 0" 203 8.5 225 7 78-5/8" 4 5.5 5/6" 007240 2" 305 0 254 8 203-5/8" 4 4.22 5/6" 00724-0 2" 305 0 254 8 203-5/8" 4 5.5 5/6" 00724 SERIES 2000 Special sizes available upon request based on minimum order quantities. Key: * Designates weights less than lb (.5kg) Consult Factory -3 205 Mobile Drill, LLC. All rights reserved.
hex-cor tm augers Don t replace the entire auger, just the shank HEX-COR TM exclusively from Mobile. Length D Available in hole sizes 2-/2" (64mm) through 2" (305mm) Hex sized 3/6", -/8", -5/8", 2 " (20.6mm, 29mm, 4mm and 5mm) Field Replacement Shank Internal Hex Tubing Hardfaced Flight Edges U-Pin Furnished with Each Section P D DIAMETER P PITCH STOCK LENGTH HOLE SIZE HEX CONN. Flight PART NUMBER in mm in mm in mm in mm ft m lb kg 6" 52 6 52 5 85 2" 5 5.5 5/6" 338582 6" 52 6 52 5 85 2" 5 5.5 /2" 338582-02 6" 52 6 52 5 85 2" 5 0 3 /2" 338582-0 6" 52 6 52 5 85 2" 5 0 3 /2" 338582-0 6" 52 6 52 5 85 2" 5 0.5 5/6" 338582-00 8" 203 7 78 7 78 2" 5 5.5 5/6" 338583 0" 203 8.5 225 8 203 2" 5 5.5 5/6" 338584 0" 203 8.5 225 8 203 2" 5 5.5 5/6" 33858 2" 305 0 254 8 203 2" 5 5.5 5/6" 338585 4" 356 2 305 9 229 2" 5 5.5 5/6" 338586 4" 356 2 305 9 229 2" 5 0 3 5/6" 338586-0 SERIES 3000-4 Special sizes available upon request based on minimum order quantities. 205 Mobile Drill, LLC. All rights reserved. Key: * Designates weights less than lb (.5kg) Consult Factory
hex-cor tm augers METER LENGTHS FOR INTERNATIONAL Requirements Length D Available in hole sizes 2-/2" (64mm) through 2" (305mm) Hex sized 3/6", -/8", -5/8", 2 " (20.6mm, 29mm, 4mm and 5mm) Field Replacement Shank Internal Hex Tubing Hardfaced Flight Edges U-Pin Furnished with Each Section P D DIAMETER P PITCH STOCK LENGTH HOLE SIZE HEX CONN. Flight PART in mm in mm in mm in mm ft m lb kg NUMBER 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 00724 4-/2" 4 4 02 3-/3 85 -/8" 29 00725 3-/2" 89 3-/4.83 3-/3 85 -/8" 29 2 007273 8" 203 7 78 7 78-5/8" 4 00726 7' 78 6 52 5 85-5/8" 4 007224 8" 203 7 78 7 78-5/8" 4 0.75 32543 7" 78 6 52 5 85-5/8" 4 0 3 50744-06 2" 305 0 254 8 203-5/8" 4 50744- SERIES Meter L. Special sizes available upon request based on minimum order quantities. COMPONENT PARTS Ref U-Pin (25 Series), 3/6" (2mm) Hex...00305 U-Pin (500 Series), -/8' (29mm) Hex...00306 U-Pin (2000 Series), -5/8" (4mm) Hex...00307 U-Pin (3000 Series), -5/8" (4mm) Hex...00308 2 Groove Pin, 3/6" (2mm) Hex...50279 2 Groove Pin, -/8" (29mm) Hex...50280 2 Groove Pin, -5/8" (4mm) Hex... (.5)...5028 2 Groove Pin, 2" (5mm) Hex...50792 3 Repair Shank, 3/6" (2mm) Hex... (.5)...003997 3 Repair Shank, -/8" (29mm) Hex...2 (.9)...003996 3 Repair Shank, -5/8" (4mm) Hex... 5 (2.3)...003995 3 Repair Shank, 2" (5mm) Hex...003998 Key: * Designates weights less than lb (.5kg) Consult Factory -5 205 Mobile Drill, LLC. All rights reserved.
STANDARD DUTY AUGERS Length D P The hex shank and socket connector are welded to the auger and a U-Pin connector is supplied with each auger section. Hardfacing of flight edges is available at an additional cost; please contact factory. Larger diameters up to 24" (60mm) are available on request, based on minimum order quantities. Special lengths are available in 0" (254mm) and 2" (305mm) diameters only. For other special lengths, see HEX-COR augers, Section. Sizes are identified by the hole size, not actual flight diameter. D DIAMETER P PITCH STOCK LENGTH HOLE SIZE HEX CONN. PART flight NUMBER in mm in mm in mm in mm ft m lb kg 4-/2" 4 4 02 3-/3 85-5/8" 4 2.60 6 5/6" 004360-02 4-/2" 4 4 02 3-/3 85-5/8" 4 5.5 42 5/6" 004360 4-/2" 4 4 02 3-/3 85-5/8" 4 0 3 86 9. 5/6" 00436 4-/2" 4 4 02 3-/3 85-5/8" 4 20 6 5/6" 50254-02 5" 27 4-/2 4 4 02-5/8" 4 5.5 44 20 5/6" 6" 52 5-/2 40 5 27-5/8" 4 3 5/6" 00760 6" 52 5-/2 40 5 27-5/8" 4 4 5/6" 004366-04 6" 52 5-/2 40 5 27-5/8" 4 5.5 48 2.8 5/6" 004366 6" 52 5-/2 40 5 27-5/8" 4 0 3 5/6" 004367 7" 78 6 52 5 27-5/8" 4 5.5 54 24.5 5/6" 004368 8" 203 7 78 7 78-5/8" 4 3 5/6" 50254-03 8" 203 7 78 7 78-5/8" 4 3 5/6" 004998 8" 203 7 78 7 78-5/8" 4 5.5 60 27.2 5/6" 004370 8" 203 7 78 7 78-5/8" 4 0 3 20 54.4 5/6" 0" 203 8.5 225 8 203-5/8" 4 5.5 90 40.8 5/6" 004374 0" 203 8.5 225 8 203-5/8" 4 0 3 27 57.6 5/6" 004375 2" 305 0 254 9 229-5/8" 4 5.5 02 46.3 5/6" 004376 2" 305 0 254 9 229-5/8" 4 0 3 35 6.2 5/6" 004377 4" 356 2 305 9 229-5/8" 4 3 5/6" 50256-05 6" -5/8" 4 3 50436 SERIES -5/8" Hex SERIES 2000 Inertia Welded HexSocket (Mobile) COMPONENT PARTS Ref U-Pin (2000 Series) -5/8" (4mm) Hex... *...00307 U-Pin 3-/2" (89mm) 2625 & 2875 Series... *...00308 U-Pin 4-/2" (4mm) 2875 Series... *...004620 2 Repair Shank 3/6" (2mm) Hex... *...00336 2 Repair Shank -/8" (29mm) Hex... *...00337 2 Repair Shank -5/8" (4mm) Hex... 7 (3.2)...503 2 Repair Shank 2" (5mm) Hex...2 (5.4)...003479 3 Repair Socket 3/6" (2mm) Hex...2 (.9)...00340 3 Repair Socket -/8" (29mm) Hex... *...0034 3 Repair Socket -5/8" (4mm) Hex...4 (.8)...50324 3 Repair Socket 2" (5mm) Hex... 6 (2.7)...003478-6 Key: * Designates weights less than lb (.5kg) Consult Factory 205 Mobile Drill, LLC. All rights reserved.
STANDARD DUTY AUGERS Length D The hex shank and socket connector are welded to the auger and a U-Pin connector is supplied with each auger section. Hardfacing of flight edges is available at an additional cost; please contact factory. Larger diameters up to 24" (60mm) are available on request, based on minimum order quantities. Special lengths are available in 0" (254mm) and 2" (305mm) diameters only. For other special lengths, see HEX-COR augers, Section. Sizes are identified by the hole size, not actual flight diameter. P D DIAMETER P PITCH STOCK LENGTH HOLE SIZE HEX CONN. PART flight NUMBER in mm in mm in mm in mm ft m lb kg 4-/2" 4 4 02 3-/3 85-5/8" 4 0.305 8 3.6 /4" SC045--625 4-/2" 4 4 02 3-/3 85-5/8" 4 2 0.6 6 7.3 /4" SC045-2-625 4-/2" 4 4 02 3-/3 85-5/8" 4 3 0.9 24 0.9 /4" SC045-3-625 4-/2" 4 4 02 3-/3 85-5/8" 4 4.2 32 4.5 /4" SC045-4-625 4-/2" 4 4 02 3-/3 85-5/8" 4 5.5 42 9. /4" SC045-5-625 4-/2" 4 4 02 3-/3 85-5/8" 4 0 3 86 9. /4" SC045-0- 625 5" 27 4-/2 4 4 02-5/8" 4 5 3 44 20 /4" SC050-5-625 6" 52 5-/2 40 5 27-5/8" 4 3.9 40 8. 5/6" SC060-3- 625-HD 6" 52 5-/2 40 5 27 6" 52 5-/2 40 5 27 No Shank Box x Box No Shank Box x Box 4'9".44 48 2.8 /4" 5.5 48 2.8 /4" SC060-57- 625 SC060-60- 625 6" 52 5-/2 40 5 27-5/8" 4 5.5 48 2.8 /4" SC060-5-625 6" 52 5-/2 40 5 27 6" 52 5-/2 40 5 27 No Shank Box x Box No Shank Box x Box 6.8 60 27 /4" 9'4" 2.85 0 50 /4" 6" 52 5-/2 40 5 27-5/8" 4 0 3 95 43 /4" 6" 52 5-/2 40 5 27-5/8" 4 5 4.5 40 63.5 /4" 6" 52 5-/2 40 5 27-5/8" 4 5.5 65 29.5 5/6" 6-/2" -5/8" 4 9'4" 285 68 30.8 /4" SC060-72- 625 SC060-2- 625 SC060-0- 625 SC060-5- 625 SC060-5- 625-HD SC065-2- 625 7" 78 6 52 5 27-5/8" 4 5.5 /4" SC070-5-625 8" 203 7 78 7 78-5/8" 4 4.2 48 2.8 /4" SC080-4-625 8" 203 7 78 7 78-5/8" 4 5.5 60 27.2 /4" SC080-5-625 8" 203 7 78 7 78-5/8" 4 5.5 73 33. /4" SC080-5- 625-HD 8" 203 7 78 7 78 2" 5 0 3 20 54.4 /4" SC080-0- 625 0" 203 8.5 225 8 203 2" 5 5.5 90 40.8 /4" SC00-5-625 2" 305 0 254 9 229-5/8" 4 5.5 02 463 /4" SC20-5-625 2" 305 0 254 9 229-5/8" 4 5.5 3/8" SC20-5-625- XHD Key: * Designates weights less than lb (.5kg) Consult Factory -7 SERIES -5/8" Hex Series 2000 Forged Hex Socket (USX) 205 Mobile Drill, LLC. All rights reserved.
FINGER BIT TYPE MULTI-PURPOSE A tough, multi-purpose auger head for full range drilling. Uses replaceable carbide insert bits. Bits are held in place with a nail. Suitable for work in light to moderate soil formations such as silt, sand, fine gravel and shale. Not recommended for gravel formations where impact could damage carbide. Cutterhead sizes are identified by hole size not actual diameter of auger. HOLE SIZE HEX CONNECTOR in mm in mm lb kg NO. BITS PER HEAD PART Number. 3-/8" 79 -/8" 29 9 4. 2 605-9 4-/2" 4 -/8" 29 5.0 4 606-92 4-/2" 4-5/8" 4 7 7.7 4 605-93 5" 27 -/8" 29 5.0 4 605-94 5" 27-5/8" 4 2 5.4 4 605-95 6" 52 -/8" 29 9 8.6 6 605-96 6" 52-5/8" 4 2.5 9.8 6 605-97 6-3/4 7-5/8" 4 2 9.5 6 605-98 COMPONENT PARTS Ref Claw Tooth Bit... *...605-2 Standard Tooth Bit... *...605-0. Claw Tooth 2. STD Tooth -8 205 Mobile Drill, LLC. All rights reserved. Key: * Designates weights less than lb (.5kg) Consult Factory
BULLDOG HEAD CONTINUOUS FLIGHT AUGERS AND BITS A tough, multi-purpose auger head for full range drilling. Uses replaceable cone-shaped carbide insert bits depending upon the formation requirements. Bits are designed to revolve during the cutting action for a more uniform wear pattern and longer service life. Recommended for abrasive conditions and difficult hard formations. Note: Bits are furnished with lock rings installed. Drill head O.D. is approximately 0% larger than corresponding auger flight O.D. Sizes are identified by the hole size, not actual flight diameter. HEX CONN. NO. BITS Used with Part No. in mm lb kg PER Head 4-/2" (4mm) hole size flight -/8 29 9 4.0 6 607-04 auger 4-/2" (4 mm) hole size flight auger -5/8 4 0 4.5 6 607-4 6" (52 mm) hole -/8 size flight auger 29 3.5 6. 8 607-06 6" (52 mm) hole -5/8 size flight auger 4 6 7.3 8 607-6 6" (52 mm) hole size flight auger 2 5 20.0 9. 8 607-25 COMPONENT PARTS Ref HF Cutterhead Body: 4-/2" (4mm), -/8" (29mm) Hex... 8 (3.6)...50230-0 HF Cutterhead Body: 4-/2" (4mm), -5/8" (4mm) Hex...9 (4.)...5023-0 HF Cutterhead Body: 6" (52mm), -5/8" (4mm) Hex...6 (7.3)...50228-0 HF Cutterhead Body: 6" (52mm), 2" (5mm) Hex...8 (8.2)...50229-0 2 BULLDOG Bit, Carbide Insert... *...50233 MINING BIT Bit prongs with brazed-on tungsten carbide inserts are set to bite for maximum penetration and minimum machine load. Recommended for medium hard nonuniform formation. Especially good for small bore horizontal or vertical holes. HEX HOLE SIZE CONNECTOR in mm in mm lb kg ASSEMBLY 2 5 3/6 2.45 00498 2-/2 64 3/6 2.45 004982 3 76 3/6 2.45 00445 3 76 -/8 29.45 200024 3-/2 89 -/8 29 2.9 004304 Key: * Designates weights less than lb (.5kg) Consult Factory -9 205 Mobile Drill, LLC. All rights reserved.
MOBILE D-P ROCK HEAD The Mobile D-P cutterhead is constructed of high tensile steel and has milled surfaces to ensure accurate bit alignment. Each shank is keyed and welded securely to the head. Tough, carbide insert bits are induction brazed for smoother, faster cutting and up to 70% longer life in the hardest formations. D-P Rock heads are recommended for use in soft shales, soft limestone and other low compressive strength rocks. Assembly part number includes full set of bits and bit punch. Sizes are identified by the hole size, not actual flight diameter. ACCESSORIES. D-P Bit Punch... *....004626 2. D-P Std Bit /2" Carbide....004627 3. D-P HD Carbide 5/8"...004627-0 4. D-P Conical...004627-02 5. D-P Claw Carbide...004627-03 HEX HOLE SIZE CONNECTOR in mm in mm lb kg ASSEMBLY NUMBER OF BITS REQUIRED 4-/2" -/8" 29 7 3.2 0048-0 5 4-/2" -5/8" 4 8 3.6 00482-0 5 6" -/8" 29 4 6.4 00483-0 7 6" -5/8" 4 4 6.4 00484-0 7 6" 2" 5 7 7.7 004623 7 8" -5/8" 4 26.8 00486-0 8" 2" 5 27 2.3 004625 9" -5/8" 4 50746 9" 2" 5 50747 0" -5/8" 4 00490-0 0" 2" 5 004624-0 2" -5/8" 4 0049-0 2" 2" 5 004625-0 4" -5/8 4 004625-04 4" 2" 5 004625-02 Conical 6" 2" 5 004623 8" -5/8 4 004625 2" 2" 5 004625-0 Assembly part number includes full set of bits. BIT 004627 2. 3. 4.. 5. -0 Key: * Designates weights less than lb (.5kg) Consult Factory 205 Mobile Drill, LLC. All rights reserved.
Especially designed cast steel bit eliminates dead-spot at hole center and bores clean, straight holes through semi-consolidated clay, loam, sand, gravel and similar formations. Cutterhead part number includes bit and shank complete. Bolt and nut included in assembly. Sizes are identified by the hole size, not actual flight diameter. TWO-PIECE FISHTAIL HEAD WITH CAST STEEL BLADES COMPLETE HEAD WITH BIT BIT ONLY SHANK ONLY HOLE SIZE HEX CONN. in mm in mm lb kg lb kg lb kg 2 5 3/6 2.5.68 004563 * * 004575 *.37 004586 2 5 -/8 29.5.68 004564 * * 004575.8.68 004587 2-/2 64 3/6 2 2.9 00435 * * 004576.8.37 004586 2-/2 64 -/8 29 2.3 004565 * * 004576.5.68 004587 3 76 3/6 2 2.9 00436.45 004577.8.37 004586 3 76 -/8 29 3.4 004566.45 004577.5.68 004587 3-/2 89 -/8 29 3.4 00437 2.9 004578.5.68 004588 4-/2 4 -/8 29 5 2.3 00438 3.4 004579.5.68 004588 4-/2 4-5/8 4 6 2.7 004567 3.4 004579 3.4 004589 5 27 -/8 29 5 2.3 00439 3.4 004580.5.68 004590 5 27-5/8 4 7 3.2 004568 3.4 004580 3.4 00459 6 52 -/8 29 5 2.3 00440 4.8 00458.5.68 004590 6 52-5/8 4 8 3.6 004569 4.8 00458 3.4 00459 6 52 2 5 5 004570 4.8 00458 4.5 2 004592 7 78-5/8 4 9 4. 0044 4.5 2 004582 3.4 00459 8 203-5/8 4 9 4. 00442 5 2.3 004583 3.4 00459 8 203 2 5 2 5.4 004572 5 2.3 004583 4.5 2 004592 0 254-5/8 4 5 00444 7 3.2 004585 3.4 00459 0 254 2 5 4 6.4 004574 7 3.2 004585 4.5 2 004592 2 305-5/8 4 * 50750 * * 50572 * * 00459 2 305 2 5 * 5075 * * 50752 * * 004592 Key: * Designates weights less than lb (.5kg) Consult Factory - 205 Mobile Drill, LLC. All rights reserved.
TWO-PIECE FISHTAIL HEAD WITH CARBIDE TIPS Carbide insert blade is recommended for stiff clay, soft shale and similar formations. Cutterhead part number includes bit and shank complete. Locking bolt and nut included in assembly. Sizes are identified by the hole size, not actual flight diameter. COMPLETE HEAD WITH BIT BIT ONLY SHANK ONLY HOLE SIZE HEX CONN. in mm in mm lb kg lb kg lb kg 2-/2 64 3/6 2 2.3.9 00722 * * 00722.8.37 004586 2-/2 64 -/8 29 2.5 00724 * * 00723.5.68 004587 3 76 3/6 2 2.9 007248.45 00747.8.37 004586 3 76 -/8 29 3.4 00749.45 00747.5.68 004587 3-/2 89 -/8 29 3.4 00725 2.9 00726.5.68 004588 4-/2 4 -/8 29 5 2.3 00727 3.4 00728.5.68 004588 4-/2 4-5/8 4 6 2.7 00729 3.4 00728 3.4 004589 5 27 -/8 29 5 2.3 00730 3.4 0073.5.68 004590 5 27-5/8 4 7 3.2 00732 3.4 0073 3.4 00459 6 52 -/8 29 5 2.3 00733 4.8 00734.5.68 004590 6 52-5/8 4 8 3.6 00735 4.8 00734 3.4 00459 6 52 2 5 5 00736 4.8 00734 4.5 2 004592 7 78-5/8 4 9 4. 00737 4.5 2 00738 3.4 00459 8 203-5/8 4 9 4. 00739 5 2.3 00740 3.4 00459 8 203 2 5 2 5.4 0074 5 2.3 00740 4.5 2 004592 0 254-5/8 4 5 00742 7 3.2 00743 3.4 00459 0 254 2 5 4 6.4 00744 7 3.2 00743 4.5 2 004592 2 305-5/8 4 * * * * * 00459 2 305 2 5 * * * * * 004592-2 205 Mobile Drill, LLC. All rights reserved. Key: * Designates weights less than lb (.5kg) Consult Factory
Especially designed cast steel bit eliminates dead-spot at hole center and bores clean, straight holes through semi-consolidated clay, loam, sand, gravel and similar formations. Cutterhead part number includes bit and shank complete. Bolt and nut included in assembly. Sizes are identified by the hole size, not actual flight diameter. TWO-PIECE FISHTAIL HEAD WITH hard FACED EDGES COMPLETE HEAD WITH BIT BIT ONLY SHANK ONLY HOLE SIZE HEX CONN. in mm in mm lb kg lb kg lb kg 2 5 3/6 2.5.68 004563-0 * * 004575-0 *.37 004586 2 5 -/8 29.5.68 004564-0 * * 004575-0.8.68 004587 2-/2 64 3/6 2 2.9 00435-0 * * 004576-0.8.37 004586 2-/2 64 -/8 29 2.3 004565-0 * * 004576-0.5.68 004587 3 76 3/6 2 2.9 00436-0.45 004577-0.8.37 004586 3 76 -/8 29 3.4 004566-0.45 004577-0.5.68 004587 3-/2 89 -/8 29 3.4 00437-0 2.9 004578-0.5.68 004588 4-/2 4 -/8 29 5 2.3 00438-0 3.4 004579-0.5.68 004588 4-/2 4-5/8 4 6 2.7 004567-0 3.4 004579-0 3.4 004589 5 27 -/8 29 5 2.3 00439-0 3.4 004580-0.5.68 004590 5 27-5/8 4 7 3.2 004568-0 3.4 004580-0 3.4 00459 6 52 -/8 29 5 2.3 00440-0 4.8 00458-0.5.68 004590 6 52-5/8 4 8 3.6 004569-0 4.8 00458-0 3.4 00459 6 52 2 5 5 004570-0 4.8 00458-0 4.5 2 004592 7 78-5/8 4 9 4. 0044-0 4.5 2 004582-0 3.4 00459 8 203-5/8 4 9 4. 00442-0 5 2.3 004583-0 3.4 00459 8 203 2 5 2 5.4 004572-0 5 2.3 004583-0 4.5 2 004592 0 254-5/8 4 5 00444-0 7 3.2 004585-0 3.4 00459 0 254 2 5 4 6.4 004574-0 7 3.2 004585-0 4.5 2 004592 2 305-5/8 4 * 50750-0 * * 50572-0 * * 00459 2 305 2 5 * 5075-0 * * 50752-0 * * 004592 Key: * Designates weights less than lb (.5kg) Consult Factory -3 205 Mobile Drill, LLC. All rights reserved.
TWO-PIECE FISHTAIL HEAD WITH CHUNKY CArbide Especially designed cast steel bit eliminates dead-spot at hole center and bores clean, straight holes through semi-consolidated clay, loam, sand, gravel and similar formations. Cutterhead part number includes bit and shank complete. Bolt and nut included in assembly. Sizes are identified by the hole size, not actual flight diameter. COMPLETE HEAD WITH BIT BIT ONLY SHANK ONLY HOLE SIZE HEX CONN. in mm in mm lb kg lb kg lb kg 2 5 3/6 2.5.68 004563-02 * * 004575-02 *.37 004586 2 5 -/8 29.5.68 004564-02 * * 004575-02.8.68 004587 2-/2 64 3/6 2 2.9 00435-02 * * 004576-02.8.37 004586 2-/2 64 -/8 29 2.3 004565-02 * * 004576-02.5.68 004587 3 76 3/6 2 2.9 00436-02.45 004577-02.8.37 004586 3 76 -/8 29 3.4 004566-02.45 004577-02.5.68 004587 3-/2 89 -/8 29 3.4 00437-02 2.9 004578-02.5.68 004588 4-/2 4 -/8 29 5 2.3 00438-02 3.4 004579-02.5.68 004588 4-/2 4-5/8 4 6 2.7 004567-02 3.4 004579-02 3.4 004589 5 27 -/8 29 5 2.3 00439-02 3.4 004580-02.5.68 004590 5 27-5/8 4 7 3.2 004568-02 3.4 004580-02 3.4 00459 6 52 -/8 29 5 2.3 00440-02 4.8 00458-02.5.68 004590 6 52-5/8 4 8 3.6 004569-02 4.8 00458-02 3.4 00459 6 52 2 5 5 004570-02 4.8 00458-02 4.5 2 004592 7 78-5/8 4 9 4. 0044-02 4.5 2 004582-02 3.4 00459 8 203-5/8 4 9 4. 00442-02 5 2.3 004583-02 3.4 00459 8 203 2 5 2 5.4 004572-02 5 2.3 004583-02 4.5 2 004592 0 254-5/8 4 5 00444-02 7 3.2 004585-02 3.4 00459 0 254 2 5 4 6.4 004574-02 7 3.2 004585-02 4.5 2 004592 2 305-5/8 4 * 50750-02 * * 50572-02 * * 00459 2 305 2 5 * 5075-02 * * 50752-02 * * 004592-4 205 Mobile Drill, LLC. All rights reserved. Key: * Designates weights less than lb (.5kg) Consult Factory
TWO-PIECE FISHTAIL HEAD WITH CARBIDE Edges COMPLETE HEAD WITH BIT BIT ONLY SHANK ONLY HOLE SIZE HEX CONN. in mm in mm lb kg lb kg lb kg 2 5 3/6 2.5.68 004563-03 * * 004575-03 *.37 004586 2 5 -/8 29.5.68 004564-03 * * 004575-03.8.68 004587 2-/2 64 3/6 2 2.9 00435-03 * * 004576-03.8.37 004586 2-/2 64 -/8 29 2.3 004565-03 * * 004576-03.5.68 004587 3 76 3/6 2 2.9 00436-03.45 004577-03.8.37 004586 3 76 -/8 29 3.4 004566-03.45 004577-03.5.68 004587 3-/2 89 -/8 29 3.4 00437-03 2.9 004578-03.5.68 004588 4-/2 4 -/8 29 5 2.3 00438-03 3.4 004579-03.5.68 004588 4-/2 4-5/8 4 6 2.7 004567-03 3.4 004579-03 3.4 004589 5 27 -/8 29 5 2.3 00439-03 3.4 004580-03.5.68 004590 5 27-5/8 4 7 3.2 004568-03 3.4 004580-03 3.4 00459 6 52 -/8 29 5 2.3 00440-03 4.8 00458-03.5.68 004590 6 52-5/8 4 8 3.6 004569-03 4.8 00458-03 3.4 00459 6 52 2 5 5 004570-03 4.8 00458-03 4.5 2 004592 7 78-5/8 4 9 4. 0044-03 4.5 2 004582-03 3.4 00459 8 203-5/8 4 9 4. 00442-03 5 2.3 004583-03 3.4 00459 8 203 2 5 2 5.4 004572-03 5 2.3 004583-03 4.5 2 004592 0 254-5/8 4 5 00444-03 7 3.2 004585-03 3.4 00459 0 254 2 5 4 6.4 004574-03 7 3.2 004585-03 4.5 2 004592 2 305-5/8 4 * 50750-03 * * 50572-03 * * 00459 2 305 2 5 * 5075-03 * * 50752-03 * * 004592 STINGER BIT The STINGER s self-centering one-piece, cast steel construction with a smooth contoured shape permits free flow of material to the auger flight. Interchangeable with the two-piece Fishtail bit, it works well in clay, loam, sand, gravel and similar formations. Designed for use with standard construction and HEX-COR augers and as a pilot bit with large diameter hollow stem augers. Sizes are identified by the hole size, not actual flight diameter. HOLE SIZE HEX CONN. HOLE SIZE HEX CONN. in mm in mm lb kg in mm in mm lb kg 2-/2 64 3/6 2 2.9 005502 5 27 -/8 29 5 2.3 005509 3 76 3/6 2 2.9 005504 5 27-5/8 4 7 3.2 00550 3 76 -/8 29 3.4 005505 6 52 -/8 29 5 2.3 0055 3-HF 76 -/8 29 3.4 005505-0 6-HF 52 -/8 29 5 2.3 0055-0 4-/2 4 -/8 29 5 2.3 005507 6 52-5/8 4 8 3.6 00552 4-/2-HF 4 -/8 29 5 2.3 005507-0 6-HF 52-5/8 4 8 3.6 00552-0 4-/2 4-5/8 29 5 2.3 005508 6 52 2 5 5 00553 4-/2-HF 27-5/8 4 6 2.7 005508-0 Key: * Designates weights less than lb (.5kg) Consult Factory -5 205 Mobile Drill, LLC. All rights reserved.
JET AUGER The premier retraction grouting tool for overburden applications with augers. MOBILOK jet augers are designed for wet or dry hard formation drilling in lime rock, bauxite or like materials. Premium MOBILOK drill rod J Series is used for the center stem and allows for circulation of drilling mud, grout or fresh water to aid in well installation or tie-back. Flight edges are hardfaced for wear resistance. Heavy wall couplings and tapered threaded connections provide an extra strong, water tight joint and speed making and breaking joints. Jet augers are identified by the hole size, not actual flight diameter. AWJ Hole Size D-Diam P-Pitch Rod I.D. Rod O.D. Coupling I.D. 4-/2" (4mm) 4" (02mm) 3-/3" (89mm) -/4" (3.75mm) -3/4" (44mm) 5/8" (6mm) NWJ Hole Size 4-/2" (4mm) 4-/8" (05mm) 3-/3" (89mm) 2-/8" (53.97mm) 2-5/8" (67mm) -/8" (29mm) 6" (52mm) 5-5/8" (43mm) 5" (27mm) 2-/8" (53.97mm) 2-5/8" (67mm) -/8" (29mm) AWJ AUGER 4-/2" (4mm) x 3'0" (94mm)...3 (5.9)...0076 4-/2" (4mm) x 5'0" (.5m)... 22 (0.0)...00627 4-/2" (4mm) x 0'0" (3.m)... 43 (9.5)...006272 NWJ AUGER 4-/2" (4mm) x 5'0" (.5m)... 46 (20.9)...006275 4-/2" (4mm) x 0'0" (3.m)... 8 (36.7)...005655 6" (52mm) x 5'0" (.5m)...53 (24.0)...006273 6" (52mm) x 0'0" (3.m)...96 (43.5)...006274 D-P ROCK HEAD 4-/2" (4mm), AWJ Pin (5 Bits)... 8 (3.6)...006290 4-/2" (4mm), NWJ Pin (5 Bits)...9 (4.)...00629 6" (52mm), NWJ Pin (7 Bits)...7 (7.7)...006293 Length P COMPONENT PARTS Carbide Insert Bit...3...(.4) 004627 D-P Bit Punch...4...(.8) 004626 3-WING CARBIDE INSERT DRAG BIT D Cutterhead: 4-/2" (4mm), AWJ Pin... 7 (3.2)...006765 Cutterhead: 4-/2" (4mm), NWJ Pin... 7 (3.2)...006766 Cutterhead: 6" (52mm), NWJ Pin...20 (9.)...006768-6 205 Mobile Drill, LLC. All rights reserved. Key: * Designates weights less than lb (.5kg) Consult Factory
AUGER RETRIEVER An auger retriever allows catching hold of HEX-COR or standard construction augers lost down the hole. Check hole size of your auger and hex shank size before ordering retriever. Retrievers are used with the continuous flight augers noted in parentheses. Sizes are identified by the hole size, not actual flight diameter. AUGER GUIDE Auger guides help position the bore hole as vertically as possible. They mount on all Mobile drill rigs and are recommended for safe operation. Sizes are identified by the hole size, not actual flight diameter. Give drill rig model and serial number when ordering. AUGER RETRIEVER - OUTSIDE TYPE 3/6" (2mm) Hex, 2-/2" (64mm) & 3" (76mm)... 7 (3.2)...00492 -/8" (29mm) Hex, 3-/2" (89mm) & 4-/2" (4mm)...20 (9.)...00493 -/8" (29mm) Hex, 5" (27mm)...6 (7.3)...00494 -/8" (29mm) Hex, 6" (52mm)...20 (9.)...00495-5/8" (4mm) Hex, 4-/2" (4mm)...26 (.8)...00496-5/8" (4mm) Hex, 5" (27mm)...27 (2.2)...00497-5/8" (4mm) Hex, 6" (52mm) & 7" (78mm)... 30 (3.6)...00498-5/8" (4mm) Hex, 8" (203mm)...3 (4.0)...00499-5/8" (4mm) Hex, 0" (254mm)... 34 (5.4)...00492-5/8" (4mm) Hex, 2" (305mm)... 36 (6.3)...004922 2" (5mm) Hex, 6" (52mm)... 32 (4.5)...003477 2" (5mm) Hex, 8" (203mm)... 33 (5.0)...004929 2" (5mm) Hex, 0" (254mm)... 35 (5.9)...004930 2" (5mm) Hex, 2" (305mm)... 37 (6.8)...00493 2" (5mm) Hex, 4" (356mm)...39 (7.7)...004932 MINUTEMAN DRILLS 2-/2" (64mm)...3 (.4)...060256 3" (76mm)... 5 (2.3)...0604 3-/2" (89mm)...4 (.8)...060457 4-/2" (4mm)...9 (4.)...060283 5" (27mm)...9 (4.)...060534 6" (52mm)... 7 (3.2)...06094 B-80, INSPECTOR SERIES DRILLS 4-/2" (4mm)...8 (8.2)...2206-0 5" (27mm)... 9 (8.6)...2206-02 6" (52mm)... 23 (0.4)...2206-03 7" (78mm)... 23 (0.4)...2206-04 8" (203mm)... 23 (0.4)...2206-05 9" (229mm) & 0" (254mm)...25 (.3)...2206-06 2" (305mm)......2207-27 4" (356mm)......2207-28 B-90 DRILL 4-/2" (4mm)......22987-0 5" (27mm)......22987-02 6" (52mm)......22987-03 7" (78mm)......22987-04 8" (203mm)......22987-05 9" (229mm)......22987-06 0" (254mm)......22987-07 2" (305mm)......22987-08 4" (356mm)......22987-09 ALL OTHER DRILLS 2-/2" (64mm)... 7 (3.2)...005257 3" (76mm)... 8 (3.6)...005258 3-/2" (89mm)...9 (4.)...005259 4-/2" (4mm)...9 (4.)...005260 5" (27mm)... 0 (4.5)...00526 6" (52mm)... 0 (4.5)...005262 7" (78mm) & 8" (203mm)... 0 (4.5)...005263 9" (229mm)...6 (7.3)...050077 0" (254mm)...8 (8.2)...005265 2" (305mm)... 30 (3.6)...050079 4" (356mm)... 32 (4.5)...005266 Key: * Designates weights less than lb (.5kg) Consult Factory -7 205 Mobile Drill, LLC. All rights reserved.
AUGER HOISTING ASSEMBLY POINTED HAMMER An auger hoisting assembly is used when it is required to pull standard construction or HEX-COR augers vertically utilizing the main hoist. This technique allows the driller to pull more than five feet of auger at a time. 3/6" (2mm) Hex Socket...2 (.9)...004656 -/8" (29mm) Hex Socket...3 (.4)...004657-5/8" (4mm) Hex Socket...4 (.8)...00457 2" (5mm) Hex Socket... 7 (3.2)...004658 AIDS IN THE REMOVAL OF GROOVE AND U-PINS. Pointed Hammer...2 (.9)...00547 AUGER PINCH BAR AUGER HOLDER (4-/4" I.D. HSA Shown) USED TO SEPARATE AUGERS. Pinch Bar...8 (8.2)...2208 An auger holder is used to temporarily support standard construction or HEX-COR augers during removal of the drill string after soil sampling or monitoring well installation has been completed. The above design is only representative. Other designs may vary. 25 Series...4 (.8)...00328 500 Series...9 (4.)...00329 2000 Series... 4 (6.4)...00330 2875 & 2625 Series...2 (9.5)...00332 Order P/N 0330 for 5" (27mm) and 6" (52mm) hole size augers in this series. DRIFT PUNCH AIDS IN THE REMOVAL OF GROOVE AND U-PINS. Drift Punch... *...006038-8 205 Mobile Drill, LLC. All rights reserved. Key: * Designates weights less than lb (.5kg) MOBILKIT Contains all the accessory tools required to facilitate auger drilling. Kits include: Retriever, Holder, Extension Rod, Pointed Hammer, Pinch Bar, and 6 U-Pins. Select by auger hex connection size and hole size. Auger Guides (in this section) are ordered separately. MOBILKIT: -/8" (29mm) Hex 500 Series Auger 3-/2" (89mm) & 4-/2" (4mm)...68 (30.8)...204-02 5" (27mm)...68 (30.8)...204-03 6" (52mm)...68 (30.8)...204-04 MOBILKIT: -5/8" (4mm) Hex 2000 Series Auger 4-/2" (4mm)...02 (46.3)...204-05 5" (27mm)...02 (46.3)...204-06 6" (52mm) & 7" (78mm)...02 (46.3)...204-07 8" (203mm)...02 (46.3)...204-08 2875 Series Auger, 0" (254mm)...32 (59.9)...204-09 3875 Series Auger, 2" (305mm)...32 (59.9)...204-0 MOBILKIT: 2" (5mm) Hex 2625 Series Auger 6" (52mm)...20 (54.4)...204-8" (203mm)...20 (54.4)...204-2 0" (254mm)...20 (54.4)...204-3 2" (305mm)...20 (54.4)...204-4 4" (356mm)...20 (54.4)...204-5 Consult Factory