Valve cover with a function of controlling closed position of the valve poppet type ULZS ED NS6, 5 up to 0 MPa up to 00 dm /min DT SHEET - OPER RTION MNU NUL WK 6 60 0.07 PPLICTION The valve cover with a function of controlling the closed position of the valve poppet type ULZS ED ED with a valve cartridge version URZS D can be used in hydraulic systems as a pilot-operated check valve, pressure reducing valve and by a combination of several elements as a multi-way control system. DESCRIPTION OF OPERTION The valve cover with a function of controlling the closed position of the valve poppet type ULZS ED ED consists of the valve body () with control bores, inductive poppet position sensor (), nozzle () and valve cartridge version URZS D - the main elements include: bushing, poppet with a damping nose (5), spring (6). The poppet is pressed against the valve seat in the bushing () by means of the spring (6). The flow is possible in both directions: from to and the opposite direction, from to. The valve poppet (5) has steps. They are three surfaces important for its operation. The surface of the seat is considered a 00%. The ring surface was created by gradation of the valve poppet (5), it is, depending on the version, 7% or 50% of the surface. The relation of the : surfaces is therefore,: or :. The surface is equal to + and can amount to 07% or 50% of the surface. The surface remains the same. y changing the ring surface, the actual size of the considered as 00% also changes. The valve opens in both directions of flow if there is no pressure affecting the surface (the connection remains without pressure) and the force of the pressure affecting respectively the or surfaces is greater than the force of the spring (6). If the surface is affected by the controlling pressure, it presses the valve poppet (5) against the valve seat in the bushing () independently from the force of the spring (6). Opening of the valve can take place by unloading the surface or by adequately high pressure at the connection, or else. The nozzle () in the controlling channel makes it possible to choose the type and time of the opening. The position sensor () allows for monitoring the closed position of the poppet (5), voltage states at the output pins of the sensor () depending on the poppet stroke (5) - see the diagram at page. ULZS5ED - 0/05DM 5 6 (00%) (7%/ 50%) (07% / 50%) Type ULZS ED - - WK 660 0.07
TECHNICL DT Hydraulic fluid Maxim imum operat ating pressure at portp orts s,, Maxim imum flow f rater Weight Maxim imum load curre c urrent of f the t sensor Connection type of the sensor mineral oil Required fluid f clec leanline ness classc ISO 06 class c 0/8/5 Nominal fluid viscosity o 7 mm /s at temperature 55 C Viscosity range,8 up to 80 mm /s o o recommended 0 C up to 55 C Fluid temperature range (in a tank) max -0 o C up to +70 o C mbient temperature range - 0 o Cup to +50 o C up to t 0 MPa NS6 NS5 NS6 NS5 Poppet position sensor inductive sensor type M Type of position sensor a sensor with two alternative outputs type PNP Supp upply volt ltage rang r of f the t sensor V DC +0% -0% up to t 0 dm /mi min up to t 00 0 dm /mi min,6 kg,9 kg 00 0 m external thread M x ; polep les (pins) INSTLLTION ND OPERTION REQUIREMENTS. Only fully functional and operational valve cover in a set with a fitted during assembly, factory sensor and valve cartridge can be used.. During operation one must keep proper viscosity of the hydraulic fluid recommended in this Data Sheet Operation Manual.. In order to provide failure-free free and safe operation of the valve cover,, one should systematically check: condition of electrical connection operation of the valve cover cleanliness of the hydraulic fluid. Due to heating of the valve cover body to high temperature, the valve cover should be placed in such a way as to eliminate a possibility of accidental contact with the valve cover body during operation or one should provide suitable covers compliant with the requirements of European standards: s PN - EN ISO 7 - and PN - EN. 5. In order to provide tightness of the valve cover connection to the hydraulic system, one should keep the dimensions of the cavity, sealing rings, tightening torques and operation parameters of the valve cover specified in this Data Sheet - Operation Manual. 6. ny changes, modifications or adjustments a to the valve cover can be made only by the producer see notes at pages and 5. 7. person operating the valve cover must be thoroughly familiar with the e content of this Data Sheet - Operation Manual. WK 6 60 0.07 - - Type ULZS ED
DIGRMS Hydraulic diagrd agram ams of f complete valve ve covers c type ULZS...ED... U wit ith valve ve cartrc artriges - version URZS...D... version ULZS...ED.../...DM... vers ersion ULZS...ED.../...DM... ULZS...ED.../...M... ULZS...ED.../...M... URZS...D...D... URZS...D... vers ersion ULZS...ED.../...DM... vers ersion ULZS...ED.../...DM... ULZS...ED.../...M... URZS...D... ULZS...ED.../...M... URZS...D... Electr lectric ical l connectc nection n diagrd agram am of f the t ind nduct uctive sensor type M PNP contact allocation - pin configuration of the sensor connection Outpu tput t state ates of f the t sesnsor type M depending ng on the posit p ition of f the t valve ve poppetp poppet stroke output state of the sensor 0 0 pin pin 0 flow through damping nose flow 0 - off neutral state on output contact - on state on output contact PERFORMNCE CURVES o measured at viscosity ν = mm /s and temperature t = 50 C Flow resist stance curc urves charactericstics p (Q) for valve cartridges - version URZS6...D... - acc. to data sheet WK 50 950 charactericstics p (Q) for valve cartridges - version URZS5...D... - acc. to data sheet WK 50 Type ULZS ED - - WK 660 0.07
OVERLL ND CONNECTION DIMENSIONS valve ve cover c - version ULZS6ED... O9 M x 7 detail 5 8 0,5 6 O 6 O5 depth 9 M8 x 0 screws 5 56 9 counterbores O9 holes 9 O6 O0 - holes O5 O,5 0,5 - Sealing ringo-rin -ring 9,5 x,78 - pcs /set () - Sealing ringo-rin -ring 0, x, - pcs /set - Sealing ringo-rin -ring 7, x, - pcs /set - Sealing ringo-rin -ring 6 x - pcs /set 5 - Spec. back-up ring 6-060 - pcs /set 6 - Fixing screwsm8 x 0-0.9 acc. topn - EN ISO 76 pcs /set; included in delivery set; tightening torque Md = Nm 7 - Overall dimension* of the valve cover - version ULZS6ED... (without sensor plug - item 8) 8 - Inductive sensor of valve poppet position typem (sensor plug not shown on the drawing, delivered on separate order acc. to data sheet WK 99 96 - order code: 76-0058990) 9 - Valve cartridgewit ith a poppet p and damp d amping nose - versions:urzs6...d...;...d... included in delivery set NOTE: (*) - Required additional distance for sensor plug - item 8 and electric wire ~ 70 mm 65 = = 6 65 6 NOTES: complete valve cover - version ULZS6ED with a valve poppet position sensor type M and valve cartridge - versions: URZS6 D ; D is factory pre-set. ny changes. modifications or adjustments to the cover can be done only by the producer. components of the set ULZS6ED cannot be changeable/used in other sets; in case of damaging the sensor, cover or cartridge, one must replace the whole cover. Type ULZS ED - - WK 660 0.07
OVERLL ND CONNECTION DIMENSIONS valve ve cover c - version ULZS5ED... O9 M x 7 detail 8 0,5 5 5 O0 depth counterbores O holes 6 O 9 0 O6 M x 50 screws 0 7 9 O O5 - holes O5 9 6 - Sealing ringo-rin -ring 9,5 x,78 - pcs /set () - Sealing ringo-rin -ring 8, x - pcs /set - Sealing ringo-rin -ring 9, x - pcs /set - Sealing ringo-rin -ring 6, x - pcs /set 5 - Spec. back-up ring 6-0590 - pcs /set 6 - Fixing screws M x 50-0.9 acc. topn - EN ISO 76 pcs /set; included in delivery set; tightening torque Md = 80 Nm 7 - Overall dimension* of the valve cover - version ULZS5ED... (without sensor plug - item 8) 8 - Inductive sensor of valve poppet position typem (sensor plug not shown on the drawing, delivered on separate order acc. to data sheet WK 99 96 - order code: 76-0058990) 9 - Valve cartridgewit ith a poppet p and damp d amping nose - versions:urzs5...d...;...d... included in delivery set NOTE: (*) - Required additional distance for sensor plug - item 8 and electric wire ~ 70 mm 85 Type ULZS ED - 5 - WK 660 0.07 = = 9 58 85 58 NOTES: complete valve cover - version ULZS5 5ED ED with a valve poppet position sensor type M and valve cartridge - versions: URZS5 5 D ; D is factory pre-set. ny changes. modifications or adjustments to the cover can be done only by the producer. components of the set ULZS5 5ED ED cannot be changeable/used in other sets; in case of damaging the sensor, cover or cartridge, one must replace the whole cover.
OVERLL ND CONNECTION DIMENSIONS valve ve covers c cavit c itie ies s type ULZS...E..ED... acc. to t DIN ISO 768 nom ominal sizes NS6, 5 n 0,,5 OD H7 5 Y H7 fitting depth 0,6,5 H H u0, OD,5,5 5 H6 H5 fitting depth H u0, H +0, H8 OD H depth 0,5 OD OD H7 L u0, L u0, Z ^ 0,05 D6 depth H - holes OD5 (max) - holes (, Y, Z, Z) L L u0, L u0, Y L u0, L u0, L u0, L Z L u0, NS φd φd φd φd φd φd5 D6 H H H H H H5 H6 H7 H8 6 5 6 6 M8 56 0 0 5 5 5 6 6 6 M 7 58 0 0,5,5,5 NS L L L L L 6 65 6 5 0,5 5 85 58 9 6 WK 6 60 0.07-6 - Type ULZS ED
HOW TO ORDER ULZS Nominal size of the cover (NS) NS6 = 6 NS5 = 5 ED D M * Type of cover with a function of electronic control of the closed position = ED Series number (00-09) - connection and installation dimensions unchanged = 0 series 0 = 0 Surface relation (:- acc. to page ) : (50%) =, : (7%) = Cracking pressure 0,05 MPa =05 0,0 MPa =0 0,0 MPa =0 0,0 MPa =0 Valve poppet with a damping nose =D Closed position control valve poppet position sensor type M Control channel without nozzle with a nozzle (diameter specified in the next step) = M = no designation = Nozzle diameter φ 0,5 mm = 05 φ0,6 mm = 06 φ0,7 mm = 07 φ0,8 mm = 08 φ,0 mm = 0 φ, mm = φ,5 mm = 5 φ,8 mm = 8 φ,0 mm = 0 φ,5 mm = 5 φ,0 mm = 0 φ,5 mm = 5 φ,0 mm = 0 Sealing NR (for fluids on mineral oil base) FKM (for fluids on phosphate ester base) = no designation = V Further requirements in clear text (to be agreed with the manufacturer) NOTES: The valve cover should be ordered according to the above coding. The symbols in bold are the preferred versions in short delivery time. Coding example: ULZS6 ED - 0/ 0 D M WK 6 60 0.07-7 - Type ULZS ED
PONR Wadowice S.. ul. Wojska Polskiego 9-00 Wadowice tel. +8 88 00 fax.+8 88 0 www.ponar-wadowice.pl WK 6 60 0.07-8 - Type ULZS ED