Pneumatic dense phase conveying by a push conveying process with high load and slow conveying speed for gentle conveying; suitable for sensitive and abrasive bulk solids, for high temperatures up to 250 C Operation purpose: Pneumatic pressure conveying vessel with complete facilities. Discontinuous operation, filling with bulk solid when the inlet valve is open under atmospheric conditions. Then locking pressure tight, and discharging the bulk solid and conveying with compressed air into the connected pipeline. Advantages: For granulates, dusts and mixtures Slow and gentle conveying with less compressed air and energy consumption Simple, cost-effective system assembly Less wear and tear due to low speed No segregation of mixtures Efficient operation even with inert gases No angel hair formation in case of plastic granulates Small exhaust air filters due to low air volumes No particle breakage due to mechanical moving parts High reliability of operation due to the possibility for controlling the working parameters approval: MIGSA SST H. Linder Date: Sign: Date: 29.9.16 Sign: Le Date: 29.9.16 Sign: Li Preliminary modifications reserved Seite 1 von 8
Operating conditions: Permissible operating pressure: 6 barü Product temperature max: 240 C Max/Min ambient temperature: -10 C T 50 C Bulk solids data: Powdered till granulates, up to middle hardness, from free flowing up to limited flowing products Typ geom. Volume dm 3 Volume for Use dm 3 permissible number of load cycles Inlet-Ø mm Height mm Weight kg PHP01207H01 125 75 durable 150 1122 235 PHP02507H01 250 180 durable 150 1422 260 PHP03507H01 350 300 durable 150 1722 285 PHP04510H01 450 300 durable 250 1687 390 PHP06510H01 650 520 durable 250 1987 435 PHP09010H01 900 750 durable 250 2287 480 PHP12010H01 1200 1050 durable 250 2687 540 PHP10013H01 1000 650 500000 350 2290 600 PHP15013H01 1500 1150 500000 350 2690 680 PHP20013H01 2000 1700 500000 350 3090 760 PHP25013H01 2500 2200 500000 350 3490 840 Seite 2 von 8
Basical version: Complete assembly -approved according to pressure equipment directive 2014/68/EU Welded steel construction carbon steel Deaeration valve with ball valve, pneumatically activated, open without current Safety valve 6 bar Pressure sensor Full level switch Material inlet valve and sender locking with a pivoting shutter type SSP Inspection nozzle Inflatable sealing Aeration stick as a discharge aid made of porous sintered stainless steel Measuring pipe for vertical or horizontal mounting, integrated in the installation of the sender or separate Pressure Vessel, category IV module G, calculated, designed and manufactured according to AD 2000 regulations Special outlet bend in abrasive resistant casted steel design This is not an equipment according ATEX-directive 2014/34/EU, but in contact with product (inside) usable in the zones 20-21-22. Additional electrical parts must be approved for the chosen ATEX-zone. Surface treatment: Chemical stripped, in contact with product conservation 10 µm with MEP100 Primer 40 µm zinc phosphate Top coat 40 µm RAL9006 grey, temperature resistant Complete pneumatic installation, for automatic operation, with -approved EMSR-technic Support, made of tubular construction with stand plates made of carbon steel Seite 3 von 8
Electric parts and sensors: Denomination Manufacturer Type Pneumatic Installation PIP001 2/2-way-solenoid valve Norgren 8240402 Pressure vessel PIP002 full level switch Endress+Hauser FTM51 Pivoting shutter PIP003 inductive sensors IFM IFS240 PIP004 solenoid valve cylinder Norgren 2623000 PIP005 solenoid valve inflatable sealing Norgren 2623100 PIP006 pressure switch inflatable sealing Wika PSM02 Deaeration unit PIP007 pressure sensor Endress+Hauser PMP131 PIP008 inductive initiators ball valve IFM IN5225 PIP009 Namur-solenoid vale ball valve Norgren 9710000 Seite 4 von 8
Options: 1. Parts in contact with product made of 1.4306 (DIN) / 304L (AISI) 2. Parts in contact with product made of 1.4404 (DIN) / 316L (AISI) 3. Parts in contact with product made of 1.4571 (DIN) / 316Ti (AISI) 4. Electrical components outside for zone 2/22 5. Electrical components outside for zone 1/21 6. Pneumatic installation in cabinet 7. Wiring of the electrical equipment and measuring points on the cabinet 8. Insulation at hot surfaces, consisting of 100 mm mineral wool and galvanized steel, covered and bolted waterproof incl. assembly 9. Electrical heating: keeping 80 C at 5 C ambient temperature, consisting of: heating cable 400V, galvanized filament grate, aluminum foil, fixing material, input- / control box in glass fibre reinforced plastic IP65 incl. temperature control thermostat and temperature limitation thermostat, incl. assembly, not for Ex-zone suitable 10. Touch protection at hot surfaces 11. Other outlet diameter Ø65, 80, 100, 125, 150 12. Sensoric for measuring of compressed air flow, temperature, humidity and pressure incl. reader unit for registration and signal processing via ethernet IP (Cloud) according industry 4.0 Seite 5 von 8
13. Suitable for -20 C ambient temperature with special valves and ejector (release of the inflatable sealing) 14. From the electric parts list deviating suppliers with special documentation 15. Vibro-sender type for mass flow, cohesive up to non-flowing products Elastic connection Elastic hanger Support, vibration resistant as a pipe construction with ground plates made of carbon steel Vibration drive with motor 230/400V IP65 Conveying tube for vibration decoupling, elastic, wear resistant Seite 6 von 8
16. Sender-scale type PHS-Heavy, all connections of the conveyor (bulk solids, pneumatic, electrical) are optimized, without secondary paths of force Inlet nozzle with centering Weighing decoupling Weighing modules, accuracy class C3, consisting of loed cell, force transmission parts and mounting parts Stable weighing frame made of profile carbon steel tube to accommodate 3 weighing modules Outlet valve Conveying tube for weighing decoupling Seite 7 von 8
17. Vibro-sender-scale type PHVS-Heavy Inlet nozzle with centering Weighing decoupling Weighing modules, accuracy class C3, consisting of loed cell, force transmission parts and mounting parts Stable weighing frame made of profile carbon steel tube to accommodate 3 weighing modules Outlet valve Conveying tube for weighing decoupling Vibration drive with motor 230/400V IP65 Related documents: 3D-Part: Type.step (example: PHP04510H01. Step) 2D-planning drawing: Type.dxf (example: PHP04510H01. dxf) Selection criteria: SG-Sender Pricelist: PL- Drawing numbers list: Draw-No-List_ Seite 8 von 8