WASTE HANDLERS 724J 744J

2 5 0 2 8 8 N E T P E A K H O R S E P O W E R J WASTE HANDLERS 724J 744J

724J Waste Handler 250 net peak hp @ 1,800 rpm 5.0 7.0-cu.-yd. buckets 49,976 51,546-lb. operating weight 13-ft. 10-in. standard height to hinge pin 15-ft. 2-in. high lift height to hinge pin Top of the heap. If yours is a vast wasteland, the 724J and 744J are your kind of waste handlers. These production machines come fully fortified to tackle tough transfer-station tasks, shift after shift. Side-by-side coolers with proportional reversible fans ensure that everything keeps cool. Extensive guarding minimizes debris buildup and keeps close encounters with obstacles from slowing you down. And a solid-state electrical distribution center, durable sealed switch pad, and state-ofthe-art diagnostic multifunction monitor further boost uptime and productivity. To learn more about the many ways these well-balanced trash handlers help make your job easier, read on. PAGES 2 3

744J Waste Handler 288 net peak hp @ 1,800 rpm 6.0 8.0-cu.-yd. buckets 65,319 66,926-lb. operating weight 14-ft. 2-in. standard height to hinge pin 16-ft. 1-in. high lift height to hinge pin Purpose-built John Deere waste handlers come fully fortified with the protection they need to excel in hostile environments. Radiators and coolers are mounted side-by-side for efficient cooling and quicker clean-out. John Deere turbocharged diesels deliver an impressive torque rise of 49 percent in the 724J and 40 percent in the 744J. So you can expect serious pull-through power when the going gets tough. Same-side ground-level daily service access makes routine tasks quick and easy. Extended service intervals and large fuel tanks further maximize uptime. Heavy-duty waste handler buckets range from 5.0 8.0 cubic yards. Third-function hydraulic valves are available for use with grapple buckets. Optional high-lift booms significantly increase dump clearance so you can push productivity to even greater heights. Choose the axles that are right for you. Hydraulic front differential lock and conventional rear are standard; front and rear hydraulic differentials are available. Heavy-duty wide axles are standard on the 744J.

The J-Series Loaders are cool to the core because their radiator and coolers aren t stacked as in some waste handlers. 1. Three-millimeter side-screen perforations act as a first filter, preventing entry of most airborne debris. Anything that gets through can easily pass through the cooler cores. Transmission oil coolers have their own air-intake screen for more efficient cooling. 2. The complete waste-handler package includes a hydraulically driven fan that automatically reverses every 30 minutes to help eliminate cooler-clogging buildup. Or hit a button from inside the cab to activate your own cleaning cycles. Plus, the grille and fan swing open a full 90 degrees when additional clean-out is necessary. 3. Part of the complete waste-handler package, the air-conditioner condenser is mounted at the roofline for maximum efficiency and easy clean-out. Optional strobe light folds down for additional overhead clearance. 4. Engine compartment baffles help prevent debris entry through the bottom. 1 2 3 4

Cool to the core. We won t claim to have figured out how to totally prevent refuse from clinging to intake screens or accumulating in belly pans. But we ve done our best at keeping debris at bay. Heavy-duty guarding is extensive, protecting all vulnerable areas. To help keep our cool, hydraulically driven fans automatically reverse periodically to blow away collected debris. And coolers have exposed side-by-side cores that are easier to clean out. For cool-running efficiency, regardless of what s underfoot or in the air. PAGES 4 5

No place for the faint of heart. No need to worry about the J-Series Waste Handlers getting trashed too soon. Their rugged reliability starts with traditional John Deere durability features such as heavy-duty turbocharged PowerTech diesels, inboard planetary axles with selfadjusting wet-disc brakes, and booms and mainframes so tough they re warranted for three years or 10,000 hours. When you know how they re built, you ll buy a Deere. PAGES 6 7

Wet-sleeve engine liners provide uniform cooling for reduced ring wear and oil breakdown and longer engine life. Sealed, gold-pin electrical connectors resist corrosion for superior long-term integrity. Purpose-built Deere PowerShift transmissions deliver the reliability and durability needed for heavy-duty work. Multifunction switchpad is sealed from dirt and proven to endure over two million cycles. Self-adjusting wet-disc brakes are mounted inboard, where they run cool, clean, and unexposed to corrosive materials. Plus, there are no exposed brake lines. Optional extreme-duty axle cooling kit helps beat the heat for longterm durability. 1. Four steel plates support the far end of the boom pivot, extending pin life while protecting the hoses. 2. Electrical distribution center employs extremely reliable circuitboard technology and solid-state switches, eliminating the need for a multitude of wiring harnesses, fuses, relays, and connections. 3. Planetary final drives are mounted inboard. Since size isn t limited by wheel hub diameter, larger and more durable components are utilized. 1 2 3

Built like a brick From the high-visibility window bars to the heavy-duty hydraulic belly pans, all vulnerable machine components are guarded to protect them from trash infiltration and impact damage. Helps keep the daily grind from grinding these highly productive trash handlers, and your operation, to a halt.

1. Articulation joint shields and driveshaft guards resist trash buildup. 2. Front window bars protect glass without obstructing all-around visibility. 3. Axle guards help protect the seals and resist refuse wrapping. 4. Extreme-duty steps are mounted in close where they re less vulnerable. Their flexible design takes abuse and comes back for more. 1 2 5. Extreme-duty front loader frame cover, lower loader frame guard, transmission side covers, and boom cylinder and hydraulic line guards give additional impact and debris resistance. 6. High-intensity halogen driving and work lights are powerful and well protected. Optional ROPS-mounted gel-filled strobe light alerts bystanders of the machine s presence. 7. Bolt-on hinged or optional hydraulic belly pans provide unmatched protection of the fuel tank and drivetrain. Hydraulic versions have built-in safety features that open and close easily for quick clean-out. 3 4 5 6 7 PAGES 8 9

Independently adjustable louvers and defrosters provide effective airflow to help keep the glass clear and the pressurized cab comfortable. Activated-carbon fresh-air filter reduces odors. Powershift torque-converter transmission employs Smart-Shift technology to ensure smooth-as-silk gear changes. Responsive steering and full 80-degree articulation increase maneuverability in tight quarters for fast cycles and fewer three-point turns. Return-to-carry, boom height kickout, and return-to-load are set with just a touch of a button. These advantages help speed production in repetitive loading applications. Industry-leading 360-degree visibility gives a clear view of the work ahead and obstacles around you. Standard 20-amp converter simplifies installation of additional radios, rear-vision camera, or other electrical devices. 1 1. Advanced, multilanguage monitor with analog gauges and LED indicators provides: Vital and general operating information including transmission mode, gear, engine rpms, and ground speed. Diagnostic readings of sensors and switches, enabling technicians to quickly troubleshoot problems. Customized machine settings that allow the operator to match the loader s operating characteristics to specific applications by preselecting transmission functions such as Quick-Shift and Auto-to-1st for maximum productivity. 2. Conveniently positioned switch module helps reduce operator fatigue with clearly visible backlit and sealed controls. 3. Located in the cab floor, the lockable master switch makes it easy to disconnect electrical power. Strobe light illuminates whenever the power is on to serve as an obvious reminder. 2 3 PAGES 10 11

Hard work made easier. From the convenient controls that let you customize machine operation, to the comfortable fully adjustable air-ride seat the J-Series Loaders have everything your operators need to stay alert and productive. All-around visibility is exceptional, offering clear sight lines to the work area and obstacles around you. And an efficient HVAC system helps keep the view clear, the environment comfortable. A sealed switch module allows convenient, fingertip control of multiple machine operations. Up-front, a stateof-the-art multifunction monitor with easy-to-read gauges and messaging provides vital operating information at a glance.

Rear access platform provides easy engine access and helps protect axles from sudden impacts. Two-stage aspirated air cleaner efficiently filters the airflow. Large hinged doors open wide for spacious access to the engine and cooling system. Hydraulic-driven variablespeed fan runs only as needed to maximize fuel efficiency. Conveniently located periodic maintenance charts help ensure that nothing is overlooked. Available enviornmental drains help prevent oil and coolant spills when changing.

Get the lowdown on daily operating costs. In addition to the enhancements that protect glass, sheet metal, and components, the J-Series Loaders are built to allow simplified maintenance. Service intervals have been extended, and same-side ground-level service points make quick work of the daily routine. Large hinged side shields open wide to provide ample access to dipsticks, vertical spin-on filters, sight gauges, and maintenance-free batteries. These, plus many other timesaving advantages, help minimize downtime and expense. 1 4 1. Vertical spin-on fuel and oil filters allow quick and easy, no-spill changes. 2. If something goes wrong, the advanced monitor gives easy-to-understand diagnostic messages and even offers possible solutions to help get you back up and running more quickly. 2 5 3. Conveniently located sight gauges let you check fluid levels at a glance. 4. Centralized lube banks make greasing less messy. 5. Your John Deere dealer has the parts and service you need, including a wide variety of preventative maintenance programs. 3 PAGES 12 13

Specifications Engine 724J WH STANDARD BOOM / HIGH LIFT Manufacturer and Model................... John Deere PowerTech TM 6081H Non-Road Emission Standards............... complies with EPA Tier 3 regulations Cylinders............................... 6 Valves Per Cylinder....................... 2 Displacement............................ 496 cu. in. (8.1 L) Net Peak Power (ISO9249).................. 250 hp (186 kw) @ 1,800 rpm Net Peak Torque (ISO9249)................. 765 lb.-ft. (1040 Nm) @ 1,300 rpm Net Torque Rise.......................... 49% Net Power Bulge......................... 16% Fuel System............................. high-pressure common rail Lube System............................ full-flow spin-on filter and integral cooler Aspiration............................... turbocharged, charge air cooled Air Cleaner.............................. dual element dry type; restriction indicator in cab monitor for service Fan Drive............................... hydraulically driven, proportionally controlled, fan aft of coolers Electrical System......................... 24 volt with 80-amp alternator Batteries (two 12 volt)..................... 1,400 CCA; reserve capacity: 440 min. each Transmission Type................................... countershaft-type PowerShift TM Torque Converter......................... single stage, single phase Shift Control............................. electronically modulated, adaptive, load and speed dependent Operator Interface........................ steering column-mounted twist-grip shift lever, quick-shift button on hydraulic lever Shift Modes............................. auto/manual, auto to 1st or 2nd, kick down or kick up/down, three clutch cutoff settings Travel Speeds* Forward Reverse Gear 1.............................. 4.6 mph (7.4 km/h) 4.9 mph (7.9 km/h) Gear 2.............................. 7.6 mph (12.2 km/h) 8.0 mph (12.8 km/h) Gear 3.............................. 14.7 mph (23.6 km/h) 15.5 mph (24.9 km/h) *Equipped with 23.5 X 25 solid rubber tires. Axles/Brakes Final Drives............................. heavy-duty inboard planetary Differentials............................. hydraulic locking front, conventional rear standard; dual locking front and rear optional Rear Axle Oscillation, Stop to Stop*........... 18 degrees Brakes (conform to SAE J1473, ISO3450) Service Brakes....................... hydraulically actuated, inboard, carrier mounted, pressure oil cooled, self adjusting, multi disc Parking Brake........................ automatically spring applied, hydraulically released, oil cooled, multi disc *Equipped with 23.5 X 25 solid rubber tires. Hydraulic System/Steering Pump (loader and steering)................... variable-displacement, axial piston pump; closed-center, pressure-compensating system Maximum Flow @ 2,200 rpm............. 74 gpm (280 L/min.) @ 1,000 psi (6895 kpa) Pressure............................. loader and steering relief 3,600 psi (24 850 kpa) Loader Controls........................... two-function valve; single- and dual-lever controls; control lever lockout feature; optional third- and fourth-function valve with auxiliary lever Steering (conforms to SAE J1511) Type................................ power, fully hydraulic Pressure............................. 3,600 psi (24 850 kpa) relief Articulation Angle...................... 80-degree arc (40 degrees each direction) Hydraulic Cycle Times Raise................................ 6.0 sec. Dump............................... 1.2 sec. Lower............................... 3.0 sec. (float down) Total................................ 10.2 sec. Turning Radius (measured to centerline of outside tire)........................... 18 ft. 0 in. (5500 mm) PAGES 14 15

Maximum Lift Capacity 724J WH STANDARD BOOM 724J WH HIGH LIFT SAE Heaped Capacity...................... 5.0-cu.-yd. (3.8 m 3 ) 6.0-cu.-yd. (4.6 m 3 ) 7.0-cu.-yd. (5.4 m 3 ) 5.0-cu.-yd. (3.8 m 3 ) 6.0-cu.-yd. (4.6 m 3 ) 7.0-cu.-yd. (5.4 m 3 ) standard lip standard lip standard lip standard lip standard lip standard lip Maximum Lift at Ground Level............ 35,496 lb. 34,094 lb. 29,344 lb. 30,802 lb. 29,677 lb. 28,592 lb. (16 098 kg) (15 462 kg) (13 308 kg) (13 969 kg) (13 459 kg) (12 967 kg) Maximum Lift at Maximum Height......... 23,633 lb. 22,989 lb. 22,548 lb. 17,779 lb. 17,219 lb. 16,906 lb. (10 718 kg) (10 426 kg) (10 226 kg) (8063 kg) (7809 kg) (7667 kg) Tires 724J WH STANDARD BOOM / HIGH LIFT Choice of Tread Width Width Over Tires Change In Vertical Height 23.5 X 25 Solid Rubber Tires............. 85.4 in. (2170 mm) 113.1 in. (2874 mm) 0 in. (0 mm) L-5 radial or bias ply tires available. Both tire types require 9-degree axle stops. Capacities (U.S.) Fuel Tank (with ground-level fueling).......... 100 gal. (379 L) Cooling System.......................... 32 qt. (31 L) Engine Lubrication, Including Full-Flow Spin- On Filter............................ 26 qt. (25 L) Powershift Transmission, Including Vertical Cartridge Filter....................... 27 qt. (26 L) Differential (each axle) Front............................... 30 qt. (29 L) Rear............................... 30 qt. (29 L) Loader Hydraulic Reservoir and Filters......... 31 gal. (118 L) Parking Brake........................... 20 oz. (600 ml) G F K L 45 H Cab and Canopy A B J D E C Dimensions with Pin-On Type Waste Buckets 724J WH STANDARD BOOM 724J WH HIGH LIFT Bucket Lip Capacity (equipped with bolt-on cutting edges) Capacity, Heaped SAE..................... 5.0-cu.-yd. (3.8 m 3 ) 6.0-cu.-yd. (4.6 m 3 ) 7.0-cu.-yd. (5.4 m 3 ) 5.0-cu.-yd. (3.8 m 3 ) 6.0-cu.-yd. (4.6 m 3 ) 7.0-cu.-yd. (5.4 m 3 ) standard lip standard lip standard lip standard lip standard lip standard lip Capacity, Struck SAE...................... 4.0-cu.-yd. (3.1 m 3 ) 5.0-cu.-yd. (3.8 m 3 ) 5.7-cu.-yd. (4.4 m 3 ) 4.0-cu.-yd. (3.1 m 3 ) 5.0-cu.-yd. (3.8 m 3 ) 5.7-cu.-yd. (4.4 m 3 ) standard lip standard lip standard lip standard lip standard lip standard lip A Height to Top of Cab.................... 11 ft. 7 in. (3522 mm) 11 ft. 7 in. (3522 mm) 11 ft. 7 in. (3522 mm) 11 ft. 7 in. (3522 mm) 11 ft. 7 in. (3522 mm) 11 ft. 7 in. (3522 mm) B Height to Top of Exhaust................. 11 ft. 4 in. (3457 mm) 11 ft. 4 in. (3457 mm) 11 ft. 4 in. (3457 mm) 11 ft. 4 in. (3457 mm) 11 ft. 4 in. (3457 mm) 11 ft. 4 in. (3457 mm) C Ground Clearance...................... 20.3 in. (516 mm) 20.3 in. (516 mm) 20.3 in. (516 mm) 20.3 in. (516 mm) 20.3 in. (516 mm) 20.3 in. (516 mm) D Length from Centerline to Front Axle........ 63 in. (1600 mm) 63 in. (1600 mm) 63 in. (1600 mm) 63 in. (1600 mm) 63 in. (1600 mm) 63 in. (1600 mm) E Wheelbase........................... 126 in. (3200 mm) 126 in. (3200 mm) 126 in. (3200 mm) 126 in. (3200 mm) 126 in. (3200 mm) 126 in. (3200 mm) F Dump Clearance, Full Height.............. 9 ft. 8.3 in. 9 ft. 1.9 in. 8 ft. 9.8 in. 11 ft. 3.9 in. 10 ft. 10.1 in. 10 ft. 6.4 in. (2954 mm) (2791 mm) (2688 mm) (3452 mm) (3305 mm) (3211 mm) G Height to Hinge Pin, Fully Raised........... 13 ft. 10 in. 13 ft. 10 in. 13 ft. 10 in. 15 ft. 2 in. 15 ft. 2 in. 15 ft. 2 in. (4209 mm) (4209 mm) (4209 mm) (4635 mm) (4635 mm) (4635 mm) H Dump Reach, Full Height................. 36.5 in. (928 mm) 42.9 in. (1090 mm) 47.0 in. (1193 mm) 45.3 in. (1150 mm) 52.2 in. (1325 mm) 56.6 in. (1437 mm) I Overall Length......................... 26 ft. 2 in. 26 ft. 11 in. 27 ft. 5 in. 27 ft. 9 in. 28 ft. 6 in. 29 ft. 0 in. (7977 mm) (8207 mm) (8353 mm) (8465 mm) (8694 mm) (8840 mm) J Maximum Rollback at Ground Level........ 37 degrees 37 degrees 37 degrees 37 degrees 37 degrees 37 degrees K Maximum Rollback at Full Height.......... 57 degrees 57 degrees 57 degrees 47 degrees 47 degrees 47 degrees L Maximum Dump Angle, Full Height......... 45 degrees 45 degrees 45 degrees 40 degrees 40 degrees 40 degrees Bucket Width............................ 114.2 in. (2900 mm) 114.2 in. (2900 mm) 114.2 in. (2900 mm) 114.2 in. (2900 mm) 114.2 in. (2900 mm) 114.2 in. (2900 mm) Breakout Force, SAE J732C................. 34,471 lb. (15 633 kg) 28,848 lb. (13 083 kg) 26,043 lb. (11 811 kg) 30,674 lb. (13 911 kg) 25,604 lb. (11 612 kg) 23,075 lb. (10 465 kg) Tipping Load, Straight..................... 44,021 lb. (19 964 kg) 42,923 lb. (19 466 kg) 41,467 lb. (18 806 kg) 35,033 lb. (15 888 kg) 33,975 lb. (15 408 kg) 32,780 lb. (14 866 kg) Tipping Load, 40-Degree Full Turn, SAE........ 38,160 lb. (17 306 kg) 37,112 lb. (16 831 kg) 35,789 lb. (16 231 kg) 30,239 lb. (13 714 kg) 29,227 lb. (13 255 kg) 28,131 lb. (12 758 kg) Reach, 45-Degree Dump, 7-ft. (2.13 m) Clearance........................... 60.2 in. (1529 mm) 63.2 in. (1605 mm) 64.8 in. (1647 mm) 77.3 in. (1963 mm) 80.8 in. (2053 mm) 82.8 in. (2104 mm) Loader Clearance Circle, Bucket In Carry Position... 42 ft. 3 in. 42 ft. 9 in. 43 ft. 0 in. 43 ft. 7 in. 44 ft. 2 in. 44 ft. 6 in. (12 884 mm) (13 023 mm) (13 115 mm) (13 292 mm) (13 450 mm) (13 553 mm) Operating Weight......................... 49,976 lb. (22 665 kg) 50,627 lb. (22 960 kg) 51,057 lb. (23 155 kg) 50,466 lb. (22 887 kg) 51,116 lb. (23 182 kg) 51,546 lb. (23 377 kg) Loader operating information is based on a machine with all standard equipment; waste handler complete protection package; 23.5 X 25 solid rubber tires; ROPS cab; differential lock front axle with standard rear axle; two-spool valve with two-lever control; heater and defroster; 175-lb. (79 kg) operator; and full fuel tank. This information is affected by tire size, ballast, and different attachments. I

Specifications Engine 744J WH STANDARD BOOM / HIGH LIFT Manufacturer and Model................... John Deere PowerTech TM 6125H Non-Road Emission Standards............... complies with EPA Tier 3 regulations Cylinders............................... 6 Valves Per Cylinder....................... 4 Displacement............................ 766 cu. in. (12.5 L) Net Peak Power (ISO9249).................. 288 hp (215 kw) @ 1,800 rpm Net Peak Torque (ISO9249)................. 970 lb.-ft. (1320 Nm) @ 1,100 rpm Net Torque Rise.......................... 40% Net Power Bulge......................... 8% Fuel System............................. mechanically actuated electronic unit injectors Lube System............................ full-flow spin-on filter and integral cooler Aspiration............................... turbocharged, charge air cooled Air Cleaner.............................. dual element dry type; restriction indicator in cab monitor for service Fan Drive............................... hydraulically driven, proportionally controlled, fan aft of coolers Electrical System......................... 24 volt with 80-amp alternator Batteries (two 12 volt)..................... 1,400 CCA; reserve capacity: 440 min. each Transmission Type................................... countershaft-type PowerShift TM Torque Converter......................... single-stage, dual-phase with freewheeling stator Shift Control............................. electronically modulated, adaptive, load and speed dependent Operator Interface........................ steering column-mounted twist-grip shift lever, quick-shift button on hydraulic lever Shift Modes............................. auto/manual, auto to 1st or 2nd, kick down or kick up/down, three clutch cutoff settings Travel Speeds* Forward Reverse Gear 1.............................. 4.6 mph (7.4 km/h) 4.6 mph (7.4 km/h) Gear 2.............................. 8.6 mph (13.9 km/h) 8.6 mph (13.9 km/h) Gear 3.............................. 13.1 mph (21.2 km/h) 19.3 mph (31.0 km/h) *Equipped with 31.5 X 25 solid rubber tires. Axles/Brakes Final Drives............................. heavy-duty inboard planetary Differentials............................. hydraulic locking front, conventional rear standard; dual locking front and rear optional Rear Axle Oscillation, Stop to Stop*........... 16 degrees Brakes (conform to SAE J1473, ISO3450) Service Brakes....................... hydraulically actuated, inboard, sun gear mounted, oil cooled, self adjusting, single disc Parking Brake........................ automatically spring applied, hydraulically released, oil cooled, multi disc *Equipped with 31.5 X 25 solid rubber tires. Hydraulic System/Steering Pump (loader and steering)................. two variable-displacement, load-sensing axial piston pumps; closed-center system Maximum Flow @ 2,250 rpm............ 104 gpm (393 L/min.) @ 1,000 psi (6895 kpa) Pressure............................ loader and steering relief 3,200 psi (22 000 kpa) Loader Controls.......................... two-function valve; single- or dual-lever fingertip controls; control lever lockout feature; optional third-function valve with auxiliary lever Hydraulic Cycle Times Raise............................... 6.5 sec. Dump.............................. 1.5 sec. Lower.............................. 3.0 sec. (float down) Total............................... 11.0 sec. Steering (conforms to SAE J1511) Type............................... power, fully hydraulic Pressure............................ 3,200 psi (22 000 kpa) relief Articulation Angle..................... 80-degree arc (40 degrees each direction) Turning Radius (measured to centerline of outside tire).......................... 20 ft. 2 in. (6140 mm) PAGES 16 17

Maximum Lift Capacity 744J WH STANDARD BOOM 744J WH HIGH LIFT SAE Heaped Capacity...................... 6.0-cu.-yd. (4.7 m 3 ) 7.0-cu.-yd. (5.3 m 3 ) 8.0-cu.-yd. (6.1 m 3 ) 6.0-cu.-yd. (4.7 m 3 ) 7.0-cu.-yd. (5.3 m 3 ) 8.0-cu.-yd. (6.1 m 3 ) standard lip standard lip standard lip standard lip standard lip standard lip Maximum Lift at Ground Level............ 45,478 lb. 43,551 lb. 38,416 lb. 36,993 lb. 36,105 lb. 35,198 lb. (20 625 kg) (19 751 kg) (17 422 kg) (16 777 kg) (16 374 kg) (15 963 kg) Maximum Lift at Maximum Height......... 23,358 lb. 22,958 lb. 22,753 lb. 20,800 lb. 20,392 lb. 20,174 lb. (10 593 kg) (10 412 kg) (10 319 kg) (9433 kg) (9248 kg) (9149 kg) Tires 744J WH STANDARD BOOM / HIGH LIFT Choice of Tread Width Width Over Tires Change In Vertical Height 31.5-25 Solid Rubber Tires.............. 94.5 in. (2400 mm) 126.0 in. (3200 mm) 0 in. (0 mm) 26.5-25 Solid Rubber Tires.............. 89.5 in. (2275 mm) 116.0 in. (2950 mm) 0.6 in. ( 15 mm) 26.5R25 X-MINE L5 Michelin Radial Tires... 86.6 in. (2200 mm) 116.2 in. (2952 mm) 1.0 in. ( 25 mm) L-5 radial or bias ply tires available. Both tire types require 8-degree axle stops. Capacities (U.S.) Fuel Tank (with ground-level fueling).......... 122 gal. (462 L) Cooling System.......................... 40 qt. (38 L) Engine Lubrication, Including Full-Flow Spin- K On Filter............................ 40 qt. (38 L) Powershift Transmission, Including Vertical 45 Cab and Canopy Cartridge Filter....................... 30 qt. (28 L) L Differential (each axle) Front............................... 52 qt. (49 L) Rear............................... 52 qt. (49 L) H Loader Hydraulic Reservoir and Filters......... 38 gal. (144 L) Parking Brake........................... 20 oz. (600 ml) G F A B J D E C Dimensions with Pin-On Type Waste Buckets 744J WH STANDARD BOOM 744J WH HIGH LIFT Bucket Lip Capacity (equipped with bolt-on cutting edges) Capacity, Heaped SAE..................... 6.0-cu.-yd. (4.7 m 3 ) 7.0-cu.-yd. (5.3 m 3 ) 8.0-cu.-yd. (6.1 m 3 ) 6.0-cu.-yd. (4.7 m 3 ) 7.0-cu.-yd. (5.3 m 3 ) 8.0-cu.-yd. (6.1 m 3 ) standard lip standard lip standard lip standard lip standard lip standard lip Capacity, Struck SAE...................... 5.3-cu.-yd. (4.0 m 3 ) 6.1-cu.-yd. (4.7 m 3 ) 7.1-cu.-yd. (5.4 m 3 ) 5.3-cu.-yd. (4.0 m 3 ) 6.1-cu.-yd. (4.7 m 3 ) 7.1-cu.-yd. (5.4 m 3 ) standard lip standard lip standard lip standard lip standard lip standard lip A Height to Top of Cab.................... 11 ft. 8 in. (3547 mm) 11 ft. 8 in. (3547 mm) 11 ft. 8 in. (3547 mm) 11 ft. 8 in. (3547 mm) 11 ft. 8 in. (3547 mm) 11 ft. 8 in. (3547 mm) B Height to Top of Exhaust................. 11 ft. 7 in. (3537 mm) 11 ft. 7 in. (3537 mm) 11 ft. 7 in. (3537 mm) 11 ft. 7 in. (3537 mm) 11 ft. 7 in. (3537 mm) 11 ft. 7 in. (3537 mm) C Ground Clearance...................... 19.9 in. (506 mm) 19.9 in. (506 mm) 19.9 in. (506 mm) 19.9 in. (506 mm) 19.9 in. (506 mm) 19.9 in. (506 mm) D Length from Centerline to Front Axle........ 67 in. (1700 mm) 67 in. (1700 mm) 67 in. (1700 mm) 67 in. (1700 mm) 67 in. (1700 mm) 67 in. (1700 mm) E Wheelbase........................... 134 in. (3400 mm) 134 in. (3400 mm) 134 in. (3400 mm) 134 in. (3400 mm) 134 in. (3400 mm) 134 in. (3400 mm) F Dump Clearance, Full Height.............. 9 ft. 9.6 in. 9 ft. 5.9 in. 9 ft. 1.3 in. 11 ft. 10.4 in. 11 ft. 7.0 in. 11 ft. 3.4 in. (2988 mm) (2894 mm) (2776 mm) (3618 mm) (3530 mm) (3440 mm) G Height to Hinge Pin, Fully Raised........... 14 ft. 2 in. 14 ft. 2 in. 14 ft. 2 in. 16 ft. 1 in. 16 ft. 1 in. 16 ft. 1 in. (4324 mm) (4324 mm) (4324 mm) (4892 mm) (4892 mm) (4892 mm) H Dump Reach, Full Height................. 47.2 in. (1199 mm) 50.9 in. (1293 mm) 54.8 in. (1391 mm) 55.9 in. (1421 mm) 59.8 in. (1520 mm) 62.7 in. (1594 mm) I Overall Length......................... 27 ft. 10 in. 28 ft. 4 in. 28 ft. 10 in. 30 ft. 0 in. 30 ft. 5 in. 31 ft. 0 in. (8495 mm) (8628 mm) (8793 mm) (9146 mm) (9279 mm) (9441 mm) J Maximum Rollback at Ground Level........ 37 degrees 37 degrees 37 degrees 35 degrees 35 degrees 35 degrees K Maximum Rollback at Full Height.......... 53 degrees 53 degrees 53 degrees 51 degrees 51 degrees 51 degrees L Maximum Dump Angle, Full Height......... 47 degrees 47 degrees 47 degrees 42 degrees 42 degrees 42 degrees Bucket Width............................ 128 in. (3251 mm) 128 in. (3251 mm) 128 in. (3251 mm) 128 in. (3251 mm) 128 in. (3251 mm) 128 in. (3251 mm) Breakout Force, SAE J732C................. 39,756 lb. (18 030 kg) 36,305 lb. (16 465 kg) 32,691 lb. (14 826 kg) 35,368 lb. (16 040 kg) 32,281 lb. (14 640 kg) 29,024 lb. (13 163 kg) Tipping Load, Straight..................... 49,024 lb. (22 233 kg) 48,082 lb. (21 806 kg) 47,099 lb. (21 360 kg) 38,817 lb. (17 604 kg) 38,105 lb. (17 281 kg) 37,425 lb. (16 973 kg) Tipping Load, 40-Degree Full Turn, SAE........ 42,235 lb. (19 154 kg) 41,364 lb. (18 759 kg) 40,464 lb. (18 351 kg) 33,203 lb. (15 058 kg) 32,528 lb. (14 752 kg) 31,898 lb. (14 466 kg) Reach, 45-Degree Dump, 7-ft. (2.13 m) Clearance........................... 70.7 in. (1797 mm) 72.7 in. (1846 mm) 74.0 in. (1880 mm) 93.0 in. (2363 mm) 95.2 in. (2419 mm) 97.0 in. (2465 mm) Loader Clearance Circle, Bucket In Carry Position............................. 45 ft. 9 in. 46 ft. 0 in. 46 ft. 3 in. 47 ft. 6 in. 47 ft. 9 in. 48 ft. 1 in. (13 938 mm) (14 018 mm) (14 104 mm) (14 470 mm) (14 561 mm) (14 658 mm) Operating Weight......................... 65,319 lb. (29 623 kg) 65,784 lb. (29 834 kg) 66,086 lb. (29 971 kg) 66,159 lb. (30 004 kg) 66,624 lb. (30 215 kg) 66,926 lb. (30 352 kg) Loader operating information is based on a machine with all standard equipment; waste handler complete protection package; 31.5 X 25 solid rubber tires; ROPS cab; differential lock front axle with standard rear axle; two-spool valve with two-lever control; heater and defroster; 175-lb. (79 kg) operator; and full fuel tank. This information is affected by tire size, ballast, and different attachments. I

724J / 744J WASTE HANDLERS Key: Standard equipment Optional equipment *See your John Deere dealer for further information and for 824J guarding. 724J 744J Engine Complies with EPA Tier 3 regulations Antifreeze, 34 F ( 37 C) Coolant recovery tank Fan guard Muffler, under hood with large exhaust stack Environmentally friendly engine oil drain Engine oil cooler Quick-release fuel filter and water separator Ether start aid (for cold starts) Engine air heater (for cold starts) Engine coolant heater, 1,000 watts, 110 volts Heavy-duty trash-resistant cooling package Chrome exhaust stack Airscreen group: Low-profile perforated hood-mounted air-inlet screen / Engine side shield inlet screens, perforated/corrugated / Engine air-intake precleaner / Engine rubber baffle Swing-out fan with heavy-duty rear grille Reversing fan, hydraulic, auto control with manual override Powertrain Torque converter, PowerShift TM transmission, computer-controlled electronic soft shift, automatic shift and quick-shift features included 3F/3R Front axle with hydraulic locking front and conventional rear differentials Wide heavy-duty front and rear axles Front and rear axles with hydraulic locking differentials Spin-control system Hydraulic System In-cab adjustable automatic bucket positioner In-cab adjustable automatic boom height kickout control In-cab adjustable automatic boom returnto-carry control Reservoir sight gauge Spin-on hydraulic filters, vertical mounting Hydraulic lever lockout Two-function hydraulic valve with two-lever fingertip control and adjustable wristrest Two-function hydraulic valve with joystick control Three-function hydraulic valve with joystick control and auxiliary lever for third function Three-function hydraulic valve with twolever fingertip control, adjustable wristrest, and auxiliary lever for third function Four-function hydraulic valve, with dual joystick control Hydraulic conversion kits, two- to threefunction valves Hydraulic conversion kits, three- to fourfunction valves Hydraulic system oil cooler (for continuous running attachments and extreme temperatures) 724J 744J Hydraulic System (continued) Ride control, automatic type Electrical Solid-state electrical power distribution system Batteries, high capacity (2), 12 volt with 1,400 CCA, 440-min. rated reserve each Alternator, high capacity, 80 amps and 24 volts Alternator trash cover Lights (conform to SAE J99): High-intensity halogen driving with guards / Turn signals and flashers / Stop and taillights Work lights, high-intensity halogen, front (2) and rear (2) LED heavy-duty taillights Horn, with push button in center of steering wheel (conforms to SAE J994, J1446) Reverse warning alarm, self-adjusting (conforms to SAE J994, J1446) Audible and visual warnings: Amber caution / Red stop / Analog gauges: Engine coolant temperature, transmission oil temperature, fuel level, hydraulic oil temperature, engine oil pressure / Digital instruments: Engine rpm, odometer, transmission gear indicator, speedometer, hour meter / Operator warning lights: Check engine, engine oil pressure, engine air filter restriction, battery voltage, transmission filter restriction, brake pressure, hydraulic oil filter, fasten seat belt, transmission fault, hydraulic oil temperature Indicator lights: Park brake / Ride control / Turn signals and warning flashers / Coupler pin disconnect / Engine preheater / Secondary steering / Work lights Radio-ready cab: Fused 24-volt radio electrical lead, and fused lead for optional Deere 5-amp and 10-amp voltage converters 24-volt AM/FM stereo radio with cassette 24-volt AM/FM stereo radio with CD Strobe light wired to master electrical disconnect switch Operator s Station Cab (conforms to SAE J1040C APR88): ROPS/FOPS / Heater/defroster / Multiplane isolation mounted for noise/vibration reduction / Front and rear windshield washers and intermittent wipers / Tinted safety glass Air conditioning Seat belt, 3 in. (76 mm), with retractor Seat, deluxe cloth covered with deep foam, high back, air suspension, adjustable for weight-height, fore-aft position, backrest tilt, and armrest angle Cup holder, personal cooler holder, and storage space Sun visor for cab Rubber floormat Steering wheel, textured with spinner knob Tilt steering column 724J 744J Operator s Station (continued) Rearview mirrors, outside (2) and inside (1) (conform to SAE J985) Waste Handler Package Waste handler guards: Articulation guards / Axle seal guards / Boom cylinder and hydraulic lines guard / Bucket cylinder hydraulic lines, zerk, and sensor guard / Driveshaft guard / Extreme-duty front loader frame cover with handles / Extreme-duty transmission side guards / Lower boom and bucket greasefitting guards / Rear loader frame cover Cab floor-mounted lockable master electrical disconnect switch Extreme-duty cab entry steps Extreme-duty hydraulic bottom guards (fuel tank, loader frame, engine frame) Bottom guards, bolt-on, front frame and transmission Full-frontal cab window guard (high-visibility version not designed to SAE J1084) Rear-access platforms with step and handhold Rear roof-mounted air-conditioner condenser with manually activated reversible electric fans Loader Linkage Loader boom service locking bar (conforms to SAE J38) Z-bar loader linkage High-lift boom Buckets and Attachments Full line of Deere pin-on buckets with selection of bolt-on cutting edges, JAGZ TM cutting edges, and teeth-segmented bolt-on cutting edges* Hydraulic control system for quick-coupler locking pins, includes all controls in cab, lines, and valves Loadrite TM weighing system* Tires 23.5 X 25 31.5 X 25 26.5 X 25 26.5 X 25 X-MINE L5 Michelin Radial L-5 radial or bias ply Less wheels and tires Multi-piece rims Other Articulation locking bar (conforms to SAE J276) Vandal protection, includes lockable engine enclosure, rear grille, and fuel fill Counterweight, built-in Drawbar, with locking pin Lift and tie-down hooks Fire extinguisher License-plate bracket Secondary steering JDLink TM Net engine power is with standard equipment including air cleaner, exhaust system, alternator, and cooling fan at test conditions per ISO9249. No derating is required up to 10,000-ft. (3050 m) altitude. Specifications and design subject to change without notice. Wherever applicable, specifications are in accordance with SAE standards. Except where otherwise noted, these specifications are based on units with all standard equipment, waste handler protection package, high-lift boom, ROPS cab, full fuel tank, and 175-lb. (79 kg) operator; a 724J unit with 23.5 X 25 solid rubber tires; and a 744J unit with 31.5 X 25 solid rubber tires. DKAJPLDRWH Litho in U.S.A. (07-04)