From Place Stamp Here Care and Use Guide UVA SunSystems, Inc. 6208 Technology Dr. Browns Summit, NC 27214 FOLD AT LINE AND SECURE WITH TAPE CUT ON DOTTED LINE SunMaster Shadow 32 Lamp Commercial Tanning Bed Important! Read this manual before installing, operating or servicing this product. Keep this manual in a safe place, for future reference. Sales and support: 1-800-274-1744 Sold by: UVA SunSystems, Inc. / SunMasterUSA 6208 Technology Dr., Browns Summit, NC 27214 v-sm32es-1 Revised: June 4, 2012
Model Length Width Lamps Amps Power Weight Limit SPECIFICATIONS Shadow (SM32ES) 86 (nominal) 39 (nominal) 32 Power Bronzer 100 14.6 120v / 15A min. 300 lbs GENERAL WARNINGS AND PRECAUTIONS DANGER: Ultraviolet radiation. Follow instructions. Avoid overexposure. As with natural sunlight, overexposure can cause eye and skin injury and allergic reactions. Repeated exposure may cause premature aging of the skin and skin cancer. WEAR PROTECTIVE EYEWEAR. FAILURE TO DO SO MAY RESULT IN SEVERE BURNS OR LONG TERM INJURY TO THE EYES. WARNING: Receive proper operation instructions from the proprietor. When using a machine with bench and canopy, pull the canopy down until it will move no futher. Recommended distance of the body from the canopy of this machine should be 6 inches. Operation of any sunbed closer than the recommended minimum distance for use may result in overexposure. Medications or Cosmetics: Some may increase your sensitivity to the ultraviolet radiation. Consult a physician before using sunlamps if you are using medications, have a history of skin problems, or believe yourself especially sensitive to sunlight. If you do not tan in the sun, you are unlikely to tan from the use of this product. Tanning may appear after one application provided that your skin is capable of developing a suntan. Allow 48 hours between sessions to obtain a base tan, and once or twice per week to maintain appearance. Recommended eyewear. Provided eye shields, such as Intrexco Nr: 563511s or equivalent eyewear as defined under 21CFR 1040.20 2(b)(6). One pair of protective eyewear is furnished with this equipment. Eyewear should be worn by all persons in the room when the lamps are on. ENSURE THAT THE SUNBED USED CONTAINS COMPATIBLE LAMPS TO THOSE LISTED HEREIN. ALL SUNBEDS HAVE LABELS STATING COM- PLIANCE WITH PERFORMANCE STANDARDS FOR SUN LAMP PRODUCTS UNDER 21 CFR PART 1040.20 BASIC INFORMATION ON THE TANNING PROCESS Melanin, the brownish pigment produced by special cells in the base layer of the skin, determines the individual s ability to tan. As the skin is exposed to ultraviolet rays, the melanin is activated and combines with protein cells that rise in the skins surface, thus producing a tan. The amount of melanin in your body determines how quickly and darkly you tan. The tan produced by the sunlamp is a cosmetic tan, however, regardless of how much an individual may tan with this unit, it will not provide adequate protection against overexposure to natural sunlight or UVB exposure. Use sunscreen outside to protect your skin. Please completely fill out this warranty card so that your warranty can be validated. Name: Address: City: State: Zip Email: Model # Serial # Purchased from: Sales representative: I learned about your company from: Internet Friend Paper Other (below) Please give us your comments on the purchasing experience: Signature: Privacy Policy Statement Your email and address information will not be sold to any other company. See website for complete privacy policy, which was desgined to protect your rights.
TROUBLESHOOTING AND MAINTENANCE PROBLEM Lamps won t light. plugged in. Some of the lights will not come on. socket. SOLUTION 1. Make sure unit is plugged in. 2. Check outlet, reset breaker if needed. 3. Verify that cords connecting bed halves to the center timer control are fully 4. Make sure timer and on/off switch are ON. 1. Check to see if lamp is installed correctly. 2. Switch bad lamp with a good lamp to see if the problem is the lamp or the Canopy won t stay 1. Make sure shocks are installed properly (ie: thicker part UP) up or down 2. Replace shock. Bed cuts off after a 1. Check source of power, reset breaker. few minutes 2. Make sure cord connecting the bed halves are FIRMLY connected to the timer box. WARNING! UNIT MUST BE DISCONNECTED FROM POWER BEFORE ATTEMPTING ANY MAINTENANCE. INTERNAL MAIN- TENANCE SHOULD ONLY BE PERFORMED BY A CERTIFIED ELECTRICIAN OR TECHNICIAN Reflex Bronzer F-71 100w Reflex LT F-71 100w This unit is designed to be virtually maintenance free. Other than lamps, no other parts are expected to need replacing for the life of the product. Clean only with the tanning bed solution provided, diluting as instructed on the bottle. More can be purchased at 1-800-274-1744. Using household chemicals can and will cause damage to the acrylic surfaces. Sunmaster Limited Warranty All SunMaster and Virtual Sun tanning beds purchased directly from UVA SunSystems, Inc. by phone or through their websites come with a One Year Limited Warranty, as stated below. For a period of one year from the date of purchase, UVA SunSystems, Inc. will provide replacement parts for parts that are shown to be defective. Lamps, acrylics and labor are covered for a period of 30 days. Under all circumstances, transporation is the responsibility of the consumer. This warranty does not cover: Abuse, misuse, unauthorized repairs or modifications, transportation, damage during transit or installation, nor normal wear and tear. UVA SunSystems, Inc. or their authorized dealers SHALL NOT BE LIABLE FOR LOSS OF USE, LOSS OF TIME, RENTAL OR SUBSTITUTE PRODUCTS, LOSS OF INCOME, LOSS OF BUSINESS, INCONVENIENCE OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. IN ANY AND ALL CASES, THE LIABILITY SHALL BE CONFIDED TO THE REPLACEMENT OF DEFECTIVE AND NON- CONFORMING PARTS. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights that vary from state to state. No one may modify this warranty in any way. Warranty claims should be made by calling 1-800-274-1744 weekdays from 9am to 5pm, excepting holidays. You may also write to: UVA SunSystems, Inc., 6208 Technology Dr, Browns Summit, NC 27214. Governing Law: This Limited Warranty shall be governed, interpreted and enforced in accordance with the substantive and procedural as of the State of North Carolina and the United States of America, conflict of law rules not withstanding. NOTICES: In order to validate this warranty, you just mail the attached warranty card and mail to the address provided within 30 days from the date of receiving your tanning bed. You must be able to provide a copy of your original receipt upon demand, or your warranty will be voided. For the purpose of this warranty, the date of purchase will be considered the day the system arrives at your home or other final destination by our carriers.
OPERATING YOUR TANNING BED BEFORE using tanning bed, cycle the timer one full time to break in lamps and verify that the timer is counting down accurately. Motorized (analog) Timer Instructions The motorized timer will automatically turn the tanning bed on when turned passed the 0 mark. Turn knob to the desired number of minutes and the bed will automatically energize and count down. If your tanning bed came with a shorting plug, then it was designed to work with either the onboard timer, or with a remote timer for commercial use. (Remote timer is not included). Using a remote timer requires a special cord to replace the shorting plug on the back of the tanning bed, which then connects to the remote timer itself. If a remote timer is used, then the onboard timer will act as an ON / OFF switch. The timer will not count down, but will allow the bed to be turned on and off if the remote timer is set to the ON position and timing down as well. This is provided so that customers in the salon will always have the option to turn the bed off before the full session is complete. Additionally, the shorting plug can be used in the home environment to disable the tanning bed, and prevent unauthorized persons from using it. In this configuration, it works as a safety device. Simply twist the locking mechanism and remove the shorting plug to disable the tanning bed. This will not remove power to the tanning bed, but will disable the timer so that it can not be energized. To restore function, simply replace the shorting plug. The shorting plug can always be found on the back edge of the canopy of the tanning bed. Universal ballast diagram To remove the shock, you need to gently pry the metal clip back, but not off, then pull end off the ball. Final steps: Make sure the shorting plug is installed into the timer port on the back of the bed. (not shown) This is a safety lock feature, and the bed will not operate unless this is in place. Now plug the cord from the bench into the slot of the canopy, to provide power to both halves, then plug in the wall. Once the bed is fully assembled and plugged into the wall, be sure to run the bed one full cycle without actually tanning, to insure the timer is operating properly.
This next step takes two strong persons, as you connect the hinge bolt into the canopy of the bed, allowing it to swivel. NOTE: Be sure to follow the diagram exactly in respect to the washers! Once you have completed this step, you will then insert the back bar that says Shadow in between the two hinges using the four supplied bolts. After these steps are all complete, you will then tighten all the bolts in the hinges until the are snug. You don t need to over-tighten them. Installing your new SunMaster E Series tanning bed Start by assembling the leg kit. It will be in a large cardboard box, along with all the misc. hard ware. (Note: the triangle pieces shown are no longer included in the kit)
Next, you will roll the bench of the tanning bed (the half that does NOT have a timer) upside down, then attach the leg kit using 6 screws. Again, the triangle pieces shown here are no longer included. You do not need to overtighten these screws. Now turn the unit right side up, and place it in its final destination. It is easier to move now than with the full weight of the bed. Once you have have turned the bench right side up, you will attache the hinges to the bench. It is often helpful to leave the bolts slightly loose during the next few steps, to allow it to flex and the bolts and holes to line up easier.