4YR Limited Warranty CUSTOM MADE EXTERI SUN SHADE MOTIZATION INSTRUCTION MANUAL
STEP Wand You may also need (A) Full Valance (Motorized) (C) Solar Panel (B) Battery (G) Shade (F) Bottom Rail (D) Bottom Rail Cap with ring (E) Quick Mount Brackets This device complies with part 5 of FCC Rules. Operating is subject to following two conditions: () This device may not cause harmful interference, and () This device must accept any interference received, including interference that may cause undesired operation. ATTENTION: For French instruction manual, please visit www.coolaroousa.com.
You may also need: IMPTANT: PLEASE READ PLEASE PLACE YOUR AUTOSUN SOLAR POWERED EXTERI SUN SHADE IN THE SUN IMMEDIATELY. PLEASE PLACE YOUR BATTERY CONNECTED TO THE SOLAR PANEL, WITH THE SOLAR PANEL FACING THE SUN. NOTE: a. Approximate installation time is 0-0 minutes. b. Two people may be required. c. Your custom blind comes with motor, battery and solar panel on right side. CARE AND MAINTENANCE: Your sun shade has been made of finest materials. To clean your shade, simply rinse with water, scrub with soap or any non-abrasive cleaner, rinse and allow to dry. Do not store shade wet. In moist areas, roll blind down frequently to air dry. WARNING: It is strongly recommended that in strong wind conditions, your exterior sun shade is completely retracted to prevent damage to windows and your sun shade. 3
Wire guide FULL VALANCE INSTALLATION COMPONENTS TEP Take all parts out of box and ensure y are all present. You may also need Bottom exposed aluminium rail Wand A. Full Valance (Motorized) x B. Battery x C. Solar Panel x D. -BRC Bottom Rail Cap with rings x E. -BRC Quick Mount Brackets x3 F. Bottom Rail x G. Shade x (A) Full Valance (Motorized) (C) Solar Panel (B) Battery (G) Shade (F) Bottom Rail (D) Bottom Rail Cap with ring (E) Quick Mount Brackets 4
Idle end unit Pelmet cap Wire guide Idle end plug Aluminium tube Bottom exposed aluminium rail Blind Pelmet Clutch plug Wand Pelmet cap Clutch unit Wire guide (9) Idle End Plug (H) Shade (8) Idle End Unit (B) Crank Handle (G) Bottom Rail. DETERMINE DESIRED MOUNTING METHOD a. This two in one valance design allows you to easily mount sun shade to eir a ceiling (fig. ) or a wall (fig. ). Ceiling (E) Bottom Rail Cap with ring (F) Quick Mount Brackets Wall (D) Bungee (C) Receiver (6) Bottom Rail (6) Quick Mount Brackets. MARK THE HOLES a. Measure inches in from each end of sun shade and mark for bracket installations. b. Mark a third location near center of sun shade for third bracket installation. c. All marks must be made to ensure a level installation of sun shade for proper functionality. Fig. Fig. (F) Quick Mount Brackets (D) Bungee (C) Receiver 3. INSTALL THE BRACKETS Unit a. In marked locations, attach Quick Mount Brackets (fig. 4, fig. 5) with screws, into wooded stud. b. The release tabs on Quick Mount Brackets must be facing out towards you on ceiling mount or downwards for a wall mount. This ensures access to tabs once sun shade is installed. Fig. 3 Inside this side goes on mounting surface ) Chain ottom Cap 4. INSTALL THE SHADE h Unit ) Chain ttom ap a. Snap shade onto Quick Mount Brackets, placing top of channel onto bracket and pushing on full valance until you hear m snap into place. b. To remove sun shade, hold in release tab on Quick Mount Bracket. (fig. 6). Fig. 4 (L) Contemporary Valance Option (J) Valance Bracket (K) Traditional Valance Outside (H) Idle End Unit (I) Aluminum Tube (B) Clutch Plug (A) Crank Unit (A) Full Valance End Plug Wood screws have been provided. If installing (F) into Shade any material (C) Crank Handle (E) Bottom Rail or than wood, additional screws may be needed. (D) If Bottom unsure, Rail Cap with ring check with a local contractor. (see below) (G) Idle You may also need Fig. 5 You may also need (E) Bottom Rail Cap with ring ) Quick Mount Brackets (D) Bungee (9) Idle End Plug (0) Aluminum Tube () Crank Unit Self tapping screws > () Clutch Plug Aluminum (8) Idle End Unit Masonry/Concrete screws > Concrete (B) Crank Handle Drywall anchors > Drywall (3) Wand (6) Bottom Rail (4) Bottom (6) Quick Mount Stainless steel > Rail Cap Outdoors Brackets with ring (C) Receiver You will need: release tab STEP Fig. 6 5 You may also need
WIRE GUIDE SYSTEM ASSEMBLY COMPONENTS Take all parts out of box and ensure y are all present. A. Bottom Brackets (small) x B. Wires (3 ft. in length) x C. Top brackets (large) x D. -BRC Bottom Rail Cap x E. Masonry Plugs x4 F. Allen Key x G. 5mm Screws x4 H. Adjustable Wire Fasteners x4 a b c d e f g 6
TOP BRACKETS STEP Remove screw end cap from bracket and feed wire through screw end cap hole (Fig ). Fig STEP Feed wire through adjustable fastener (as pictured) and tighten with Allen key (provided). Leave approximately /4 in. wire overhang. If wire won t feed through adjustable wire fasteners, you will need to use an allen key to open it up (Fig 3). Fig STEP 3 Pull wire and adjustable wire fastener back through screw end cap, and screw back onto top wire guide bracket (Fig 4). STEP 4 Repeat steps 4 for or top side wire guide bracket. Fig 4 Fig 5 7
BOTTOM BRACKETS STEP Extend roller blind out to your full desired length. The two bottom wire guide brackets will sit below base rail (as pictured in Fig ). NOTE: Allow for any kind of obstacles such as window winders and window sills, etc. Fig STEP Remove screw end cap from bottom wire guide bracket and feed wire through (Fig ). STEP 3 Feed wire through adjustable wire fastener. If wire won t feed, use allen key to open it (Fig 3). Fig Fig 3 8
STEP 4 Tighten adjustable fastener with Allen key provided at your desired length, at least 3/4 in. below base rail (Fig 5 & 6). IMPTANT: a. Locate an area on wall/floor that is suitable for bottom bracket to be screwed into. Ensure wire guide reaches suitable drilling point for bottom bracket. If not, readjust fastener to correct length. b. Allow for any kind of obstacles such as window winders and window sills, etc. STEP 5 When you are confident you have right length, cut excess wire with pliers (as pictured). Leave approximately /4 in. wire overhang (Fig 7). Fig 5 Fig 6 At least 0mm STEP 6 Reattach bottom bracket by screwing end cap back into bracket. Pull wire guide down tight. STEP 7 Using a pencil, mark drilling holes for bracket installation (Fig 8). IMPTANT: Ensure bottom bracket is vertically aligned with top bracket. Fig 7 Fig 8 9
STEP 9 Drill holes for screws (Fig 9). STEP 0 Screw bottom bracket into wall/floor. Ensure bottom wire guide bracket anchor points up (Fig 8). NOTE: Use masonry plugs if installing directly into concrete/brick wall. Do not install directly into mortar between bricks. Fig 9 STEP Screw cap down until wire becomes taut. STEP Repeat process for or side bottom wire guide bracket. STEP 3 Wire guide installation is now complete, and your roller blind should move freely up and down wire guide system, with use of crank operating wand (Fig 0). Fig 0 0
CHANGE DIRECTION OF BRACKET ANCH POINTS (IF DESIRED) STEP Remove screw end cap (Fig ). STEP Locate Philips head screw inside thread. Use a Philips head screw driver to remove screw and thread (Fig ). Fig STEP 3 Reattach in desired direction. Replace end cap (Fig 3). STEP 4 Now follow instructions from Blind Assembly (page 5) and Wire Guide System Assembly (page 6) to install your blind and wire guide. Fig Fig 3
AUTOSUN INSTRUCTIONS COMPONENTS Take all parts out of box and ensure y are all present. The AutoSun system is a complete solar powered motor system. It is comprised of: AutoSun DC ESPHz motor AutoSun battery AutoSun solar panel 54 3 4 - V solar panel : Provide energy needed by Autosun system - Current supplied by panel (Isc) : 96 ma +/- 0% - Voltage supplied by panel (Uoc) : V +/- 0% - Power : 3.W - NiMh V -.Ah battery pack - Store electrical energy provided by solar panel. - Supply electrical energy required by motor. - Enable programming of motor using programming button. 3- T3.5 DC ESPHz motor 4- Charger / emergengy power supply (NOT INCLUDED) - Allows rapid recharging of battery for Autosun system in case of prolonged low sun level. charges / year max. (SOLD SEPARATELY) - The solar panel captures sun s rays and generates electricity. - The electricity is transmitted from solar panel to battery. 3- The battery powers shade s motor. The shade is controlled by radio control Somfy transmitter. 3
SOLAR PANEL MOUNTING OPTIONS AND RECOMMENDATIONS VISUAL COMPONENT GUIDE b battery V -.Ah ref.: 904734 a. PRESENTATION a. By converting solar energy to electrical energy, solar panel (Ref: 90903) charges battery pack. b. Current supplied by panel (Isc): 96 ma +/- 0% battery V -.Ah ref.: 904734 c. Voltage supplied by panel (Uoc): V +/- 0% d. Power: 3,W Fig. b a T3.5 DC EHz Fig.. FASTENING THE SOLAR PANEL BY RIVETING The solar panel should preferably be placed on an open area, eir on a pergola, gazebo, or wall so as to be exposed as 6 mm possible to sun s rays. 6 mm Fig. 3 a. Ensure that cables are not damaged during installation. Smooth edges of all drilled holes. b. Do not put anything on solar panel that would filter sun s rays (ex. paint). c. Keep photovoltaic cells clean by cleaning m with clean 6 mm water, using a soft cloth to avoid scratching m (once a month). 6 mm d. In winter do not allow snow to build up on panels. NOTE: The optional extension cable (sold separately) must be integrated into a UV resistant conduit. CAUTION! The cables and connectors must be protected from shade movement... Holes in box and console. (WARNING: do not drill into panel) (fig. A and B).3. Fixing panel. (fig. 3) 470 mm Fig. 4 470 mm 60 mm 8 0,5 449 Ø6 Ø6 470 mm 60 mm 8 0,5 30 470 mm 0,5 60 mm 449 8 0,5 Ø6 30 449 Fig. A 8,7 mm Max. 60 mm 30 30 449 8 Ø6 Fig. B 8,7 mm Max. 8,7 mm Max. Fig. C 3
SOLAR PANEL MOUNTING OPTIONS AND RECOMMENDATIONS (continued) 909683 = + x + x x Fig.. FASTENING THE SOLAR PANEL USING THE MOUNTING BRACKETS ❶ 0,5 ❶ 449 7 ❶ a. The solar panel should always be placed on an open area, eir on a pergola, gazebo, or wall so as to be exposed as possible to sun s rays. Ø4mm 3 4 3 Ø4mm 4 Ø4mm b. Use optional solar power mounting brackets to tilt solar panel towards greatest exposure to sun. (Fig. -6) Fig. ❶ c. Use specially designed fasteners to fasten to panel ❶ Fig. 3 IMPTANT: DO NOT DRILL INTO THE PANEL ❷ ❷ Fig. 4 ❸ ❸ ❸ Push >>> Fig. 5 ❶ ❶ ❶ ❶ 9097 4 Fig. 6
BATTERY MOUNTING OPTIONS. PRESENTATION GB BATTERY PACK AUTOSUN - 904734 The battery pack used in AutoSun solar system has following functions: Presentation a. Store electrical energy provided by solar panel. b. Supply electrical energy required by motor. Technical Data for battery: Technical data: NiMh battery - V/. Ah Battery life: approx. 5 years Storage temperature: -0 degrees F/+70 degrees C Operating temperature: -0 degrees F/+70 degrees C Storage time: max. 6 months at 0 degrees - Weight C : 0.790 Kg Protection index: IP X4 NiMh Approximate weight:.75 lbs. - For more information about installation of battery depending on th Recommendations NiMh NiMh Screw fixing - Recharge battery before use with charger ref.: 904738. WARNING: Do not charge at a temperature above 70 C. - Charge duration: 3h 30 min. max. charges by year max. Recommendations - Never leave a battery in a discharged condition. 8 - No not open or pierce battery. - Recharge - Recharge battery battery before before use use with with charger charger ref.: ref.: 904738. 904738. WAW - Do not put battery into a fire, risk of explosion. Keep away (m minimum) from from all types 4 - Charge of - Charge flames, duration: sparks duration: or 3h incandescent 3h 30 min. 30 min. max. material. max. charges charges by by year year max. max. 0 - Do not create a short circuit on battery terminals: danger of burns and explosion. - Never - Never leave leave a battery a battery in a in discharged a discharged condition. condition. - The battery must be sheltered from rain (IP X4). - No - No not not open open or pierce or pierce battery. battery. - The battery must be accessible in order to carry out possible recharging (see instruction sheet 50559). - Do - Do not not put put battery battery into into a fire, a fire, risk risk of explosion. of explosion. Keep Keep away away (m (m minimu Ø 3 - Suitable substrates for sticking: runners and box in aluminium, box in PVC (remove protective films).the surfaces to be glued must be dry 3 and clean. - Do - Do not not create create a short a short circuit circuit on on battery battery terminals: terminals: danger danger of burns of burns and an e - The ambient temperature when gluing should be between 0 C and 38 C. - We recommend users run industrial tests in exactly same conditions as those of intended - The - The application battery battery and must must reby be sheltered be sheltered ascertain from from that our rain rain product (IP X4). (IP X4). satisfies its requirements. If in doubt, opt for screwing solution. - The - The battery battery must must be accessible be accessible in order in order to carry to carry out out possible possible recharging recharging (se 478,5 - The battery must be replaced by a professional with an identical model. - Suitable - Suitable substrates substrates for for sticking: sticking: runners runners and and box box in aluminium, aluminium, box box in PVC in PV - Do not put in dustbin, this is a recyclable product. - The - The ambient ambient temperature when when gluing gluing should should be between between 0 C 0 C and and 38 C 38 - We - We recommend users users run run industrial industrial tests tests in exactly in exactly same same conditions conditions as 3 Mounting requirements. If in If doubt, in doubt, opt opt for for screwing 4 screwing solution. solution. - The - The battery battery must must be replaced be replaced by a by professional a with with an identical an identical model. model. - For more information about installation of battery depending on type of case, see Technical - Do - Do not booklet not put put ref: in in 5059076 dustbin, dustbin, this this a is recyclable a recyclable product. product. Screw fixing Fig. 3 Glue fixing 3 3Mounting - For more about installation of battery depending on th 8 - For more information about installation of battery depending on ty 4 Connection - Use solvent* of to battery clean and pack wipe surface for gluing. 0 4 Screw Screw fixing fixing - Pass battery pack cable into base. - The terminal connector () is for Ø 3mm 3 - Remove protective paper - from The 4 terminal adhesive. connector 8 8 () is for 3 0 0 4 - Press battery pack onto frame. 478,5 Ø 3mm Ø 3. MOUNTING BATTERY PACK WITH TAPE (OPTION ) a. Use solvent to clean and wipe surface for gluing. b. Pass battery cable into base. c. Remove protective paper from adhesive. d. Press battery pack into frame. NOTE: Use a solvent containing a mixture of isopopyl alcohol and water (50/50) or a heptane-based solvent. Follow all safety instructions concerning handling of solvents. 3. MOUNTING THE BATTERY PACK WITH BATTERY MOUNTING BRACKETS (OPTION ) a. Measure brackets for mounting battery. b. Mount brackets with appropriate hardware to surface. c. Insert corded end bracket to corded end, insert non corded end to its bracket. The battery pack used in Autosun solar system has follow - Store electrical energy provided by solar panel. - Supply electrical energy required by motor. - Enable programming of motor using programming but 503 30 7 Technical d S.A.S. au capital de 5 000 000 - Z.I. Les Giranaux - BP7-7003 Arc-Les-Gray - Do not put battery into a fire, risk of explosion. Keep away (m min - Do not create a short circuit on battery terminals: danger of burns a 505590A - NiMh batte - Battery life - Storage te GB GBBATTERY PACK PACK AUTOSUN - - 904734 Operating - Read carefully se - Storage tim instructions before any use. - Protection - Weight : 0 S.A.S. au capital de 5 000 000 - Z.I. Les Giranaux - BP7-7003 Arc-Les-Gray CEDEX - RCS GRAY B 45 650 090 - SIRET 45 650 090 000 - n T.V.A CEE FR 87 45 650 090 S.A.S. au capital de 5 000 000 - Z.I. Les Giranaux - BP7-7003 NiMh Presentation The battery pack used in Autosun solar system has following functions: Recommendations - Store electrical energy provided by solar panel. The The battery battery pack pack used used in in Autosun Autosun solar solar system system has has following Fig. - Supply electrical energy required by motor. - Store - Store electrical electrical energy energy provided provided by by solar solar panel. panel. - Recharge battery before use with charger ref.: 904738. - Enable programming of motor using programming button. - Supply - Supply electrical - Charge electrical duration: energy energy required 3h 30 required min. by max. by motor. charges motor. by year max. - Enable - Enable programming - Never leave a battery of of in a motor discharged motor using using condition. programming button. - No not open or pierce battery. - The battery must be sheltered from rain (IP X4). - NiMh battery - V /, Ah - The battery must be accessible in order to carry out possible Technical Technical recharging data: - Battery life: approx. 5 years - Suitable substrates for sticking: runners and box in aluminium, box in P - Storage temperature: -0 / +70 C - The ambient Connector temperature for charger when gluing should be between - NiMh - NiMh 0 C battery and batte 3- - Operating temperature: -0 / +70 C - Storage time: max. 6 months at 0 C - Protection index: IP X4 - We recommend users run industrial tests in exactly - Battery same - Battery condition life: life: ap requirements. If in doubt, opt for screwing solution. - Storage - Storage tempe - The battery must be replaced by a professional with an - Operating identical - Operating model. temt - Do not Programming put dustbin, button this is a recyclable product. - Storage - Storage time: timm - Protection i 3 Mounting - Protection inde - Weight - Weight : 0.790 : 4 503 Connection of battery pack 30 7 - The terminal connector () is for connection to solar panel ref: 904736 - The 4 terminal connector () is for connection to T3.5 DC EHz motor 4 4 Fig. * Use a solvent containing a mixture of isopopyl alcohol and water (50/50) or a heptane-based solvent. Follow all safety instructions concerning handling of solvents. Fig. 4 503 503 4Connection of of battery battery pack pack 30 30 7 7 5 478,5 478,5 - The - The terminal terminal connector connector () is () for is for conn c - The - The 4 terminal 4 terminal connector connector () is () for is for conn c 5
settings for direction of rotation - Do and not end recharge limits or are retained. battery typ Per tion.c n operation 3 to programme battery a new - réf.904734), individual controller. re is a - Keep away (m minimum) from f POWERING UP YOUR SOLAR 9. Complete cancelling of programming - Do not open charger, risk of e 8. Cancelling - Do all not use programmed charger if trans cab - Press PROG key of battery pack more than seconds. The motor w POWERED SOLAR SHADE - Press PROG - Do key not of cover battery during pack more use. than 7 sec run 3 times in one direction and n in or. The operation is completed. for in one direction and n in or. The operation is The motor returns to its original The motor set doesn't up, with have no any transmitter transmitter programmed programme LED in memory. Redo complete settings programming for direction procedure of rotation for and end mot limi (direction of rotation, end tion limits.c and n control operation points). 3 to programme a new indiv YOUR SOLAR POWERED EXTERI SUN SHADE COMES FROM THE FACTY AT COOLAROO WITH AN INITIAL CHARGE, 0. Battery protection 9. Complete against cancelling excessive of discharge programming PLEASE INSTALL YOUR SHADE PROMPTLY PLACE THE Before each lifting or lowering - Press of PROG shutter, key of battery motor pack checks more than volta se SOLAR PANEL, CONNECTED TO THE BATTERY AND FACING run 3 times in one direction and n in or. The ope If voltage is below.5v: The motor will pause at beginning of e THE SUN SO IT DOES NOT LOSE ITS CHARGE. The motor Fig. returns to its original set up, with no trans only be closed by pressing several times on in memory. - Connect Redo complete charger to programming mains proc sup If voltage is below 0V: (direction The receiver - of Open rotation, won t battery end accept limits cover. and any control commands. points). WARNING: Do not charge at a temperature above 70 In degrees se two C. cases, use 3-emergency Disconnect charger battery in from order to moto per motor will return to normal 0. Battery 4- Connect only protection if battery against charger voltage excessive to battery. goes at Before each lifting or lowering of shutter, moto - Do not recharge or battery - types Maximum besides charging those provided time for for bat th If voltage is below.5v: The motor will pause. CHARGING BATTERY WITH OPTIONAL CHARGER (SOLD battery - réf.904734), re is - a risk charges of explosion. / year only be max. closed by pressin SEPARATELY) - Keep away (m minimum) If voltage from is - below Minimum from 0V: all types charging The receiver of flames, time won t to sparks accept be abl o - Do not open charger, risk of electric shock. In se two cases, use emergency charge - Do not use charger Charge duration: 0 min. max. charges by year max. motor if will cable return is damaged. to normal only if batter - Do not cover during use. Never leave a battery in a discharged condition. - Do not recharge or battery types besides tho battery - réf.904734), re is a risk of explosio No not open or pierce battery. LED - Keep away (m minimum) from from 5all types o Do not put battery into a fire, risk of explosion. Keep - Do not open charger, risk of electric shock. - Do not use charger if cable is damaged. away (m minimum) from from all types of flames, sparks or 0 min. - Do not cover during use. incandescent material. Do not create a short circuit on battery terminals: danger LED 5- Charging is finished when LED chan of burns and explosion. 6- Reconnect battery to motor. The battery must be sheltered from rain (IP - X4). Connect charger to mains 7- Fig. Replace supply. The battery two-colour cover. LED (green The battery must be accessible in order to carry -out Open possible battery cover. 3- Disconnect battery from motor. recharging (see instruction sheet 50559). 4- Connect charger to battery. The LED changes colour from gre Suitable substrates for sticking: runners and box in aluminium, - Connect - Disconnect charger to mains battery supply. pack, The two-c m - Maximum charging - time Open for box in PVC (remove protective films).the surfaces to be - Replace battery: cover. 3 hours battery 30 pack min. (c). with - charges / year max. 3- Disconnect 3- Charge battery from new pack. motor. Connect th glued must be dry and clean. The ambient temperature when gluing should be between 0 C (68 F) and 38 C (00.4 F). We recommend users run industrial tests in exactly same conditions as those of intended application and reby ascertain that our product satisfies its requirements. If in doubt, opt for screwing solution. 0 min. - Minimum charging 4-time Connect to be able charger to open to battery. shutter The (with LED change a ba - Maximum charging time for battery: 3 hours - charges / year max. - Minimum charging time to be able to open 5 The battery must be replaced by a professional with an identical model. 0 min. 5- Charging is finished when LED changes colour back to green. Disconn Do not put in dustbin, this is a recyclable product. 6- Reconnect battery to motor. 7- Replace battery cover. 5- Charging is finished when LED changes colour back 6- Reconnect Fig. battery 3 to motor.. Battery pack 7- replacement Replace battery cover.. Battery pack replacement - Disconnect battery pack, motor (a) and solar panel - Replace battery - pack Disconnect (c). with an battery identical pack, model. motor (a) and 3- Charge new pack. Connect new pack to motor and 5 - Replace battery pack (c). with an identical m 3- Charge new pack. Connect new pack t 6
The motor doesn't have any transmitter 0. Battery programmed protection in its memory against any - Do more, not excessive open but discharge charger, risk 7s of e settings for direction of rotation and end limits are retained. Perform - Do not operation.c n operation 3 to programme a new individual controller. - Do not cover during use. use charger if cab Before each lifting or lowering of shutter, motor checks volta s If voltage is below.5v: The motor will pause at beginning of e POWERING UP YOUR SOLAR only be closed by pressing several times on 9. Complete cancelling of programming LED If voltage is below 0V: The receiver won t accept any commands. POWERED SOLAR - Press PROG SHADE key of (continued) battery pack In se more than two cases, seconds. use The motor emergency will charger in order to per run 3 times in one direction and n in motor or. will The return operation to normal is completed. only if battery voltage goes a The motor returns to its original set up, with no transmitter programmed s 8. IMPTANT: Cancelling all programmed in memory. transmitters Redo complete programming - Do not recharge procedure or for battery motor types besides those provided for th battery - réf.904734), 8. re Cancelling is a risk of all explosion. programmed s tran (direction of rotation, end limits and control points). 7s - Press PROG key of battery pack more than 7 seconds. The motor will run times Do not recharge or battery types besides those provided - Keep away (m minimum) from from all types of flames, sparks o for in one direction and n in or. The operation is completed. - Press Fig. PROG key of battery pack more than 7 s for Autosun system 0. (rechargeable Battery protection NiMh against - Do excessive not open discharge charger, for in - one risk Connect direction of electric and n shock. charger in to or. The mains operation The motor doesn't have any transmitter programmed in its memory any more, but 7s sup - Do not use charger The if motor - Open cable doesn't is have damaged. battery any cover. transmitter programm settings V - for.ah direction battery of - Before rotation réf.904734), each and lifting end limits re or lowering are is retained. a risk of of Perform shutter, explosion. operation.c n operation 3 to programme battery from moto - Do not cover motor during checks use. settings voltage 3- Disconnect sfor of direction battery. of rotation and end lim Keep away (m minimum) If voltage a new from is from below individual all.5v: controller. types The of motor flames, will pause at beginning tion.c n of each operation command 5s 3 to programme to lift a shutter. new ind 4- Connect charger to battery. T only be closed by pressing several times on "down" button. 9. Complete sparks or cancelling incandescent material. LED If of programming voltage is below 0V: The receiver won t accept any commands. 9. Complete cancelling - Maximum of programmin charging time for bat Do not open charger, risk of electric shock. - Press PROG key of battery pack In se more than two cases, seconds. use The motor emergency will charger in order - Press to PROG perform - charges key a of quick / year battery battery max. pack more recharge than Do not use charger if cable is damaged. run 3 times in one direction and n in motor or. will The return operation to normal is completed. run 3 times in - Minimum one direction charging and n in time or. to be The abl o only if battery voltage goes above V. The motor Do not returns cover to its during original use. set up, with no transmitter programmed sthe motor returns to its original set up, with no tra - Do not recharge or battery types besides those provided in memory. for Redo Autosun complete system (rechargeable programming prn in Maximum memory. Redo charging complete time programming for battery: procedure 0 min. for motor battery - réf.904734), re is a risk of explosion. s(direction of rotation, end limits and control points (direction charges of rotation, / year end limits max. and control points). 7s - Keep away (m minimum) from from all types of flames, sparks or incandescent s material. Minimum charging time - to Do be not able open to open charger, risk - shade Connect of electric (with shock. 0. a charger to mains Fig. Battery protection against excessi supply. The two-colour LED (green 0. Battery protection against excessive discharge 5 battery in good condition): - Do 0 not minutes. use charger if - Open cable is damaged. battery cover. Before each lifting or lowering of shutter, m Before each lifting or lowering of shutter, - Do not cover motor during checks use. 3- voltage Disconnect of battery. from If voltage motor. is below.5v: The motor will pause a If voltage is below.5v: The motor will pause at beginning 4- Connect of each command charger to to lift battery. shutter. The 0 The LED shutter min. changes can only be closed by pres colour from gre If voltage is below 0V: The receiver won t accep only be closed by LED pressing several times on "down" button. A. Connect charger (sold separately) to main supply. - Maximum If voltage is below 0V: The receiver won t accept any commands. The charging time In for se battery: two cases, 3 hours use 30 emergency min. char - charges / year max. motor 5- Charging will return is finished to normal when only if LED chan batt two-colour In se two LED cases, (green use / red) emergency lights charger up green, in order charger to perform is ready - Minimum a quick charging battery time recharge. to 6-be Reconnect able Operation to open battery of shutter to motor. - Do not recharge (with a ba use. 7- Replace 3 or battery types besides t motor will return to normal only if battery voltage goes above V. battery cover. battery - réf.904734), re is a risk of explo B. - Disconnect Do not recharge or battery from types besides motor. those provided for Autosun system (rechargeable - Keep away NiMh (m V minimum) -.Ah from from all type C. Connect battery - réf.904734), charger re to is a battery risk of explosion. cable. The LED changes - Do not open charger, risk of electric shoc colour - Keep from away green (m minimum) to red. from from all types of flames, sparks or incandescent material. - Do not use charger if cable is damage - Connect charger to mains supply. The two-colour LED - - Disconnect battery pack, m 5(green Do Fig. not 3 cover / red) during lights use. - Do not open charger, risk of electric shock. up green, charge D. Charging is finished when - Open LED battery changes cover. colour back to - Replace battery pack (c). with - Do not use charger if cable is damaged. green. Disconnect charger 3- Disconnect from battery. from motor. 3- Charge LED - Do not cover during use. new pack. Connect th 0 min. E. Reconnect battery 4-to Connect motor. charger to battery. The LED changes colour from green to red. LED - Maximum charging time for battery: 3 hours 30 min. 5- Charging is finished when LED changes colour back to green. Disconn - charges / year max. 6- Reconnect battery to motor. - Minimum charging time to be able to open shutter (with a battery in good condition): 0 minu Your solar powered shade is now ready for use. 7- Replace battery cover. 3 - Connect charger 4 to mains supply. The two. Battery pack replacement - Open battery cover. 3- Disconnect battery from motor. NOTE: If battery is fully discharged due to lack - of Disconnect sun, solar battery 4-pack, Connect motor charger (a) to and battery. solar The LED panel chan - Connect panel was charger covered, to etc., mains you supply. can place The two-colour solar LED panel 5 (green 6 - Replace in / direct red) lights sun battery up green, pack (c). Fig. charger with 4 an is identical ready to use. - Maximum charging time model. for battery: 3 hou - Open battery cover. for several hours a day. If charge doesn t happen, 3- Charge you may new pack. Connect - charges / new year max. pack to motor and 3- Disconnect battery from motor. 0 min. - Minimum charging time to be able to open th 4- Connect need to purchase charger to a charger battery. via The our LED website, changes colour www.coolaroo.com, from green to red. or contact customer service at -800-560-4667. - Maximum charging time for 5- Charging battery: is 3 finished hours when 30 min. LED changes colour back to green. Disconnect charger from battery an - charges / year max. 6- Reconnect battery to motor. - Minimum charging time to 7-be Replace able to open battery cover. shutter (with a battery in good condition): 0 minutes. 5. Battery pack replacement 0 min. - Disconnect battery pack, motor (a) and solar panel (b) 5 - Replace battery pack (c). with an 6 identical model. Fig. 5 6- Reconnect battery to motor. 3- Charge new pack. Connect new pack to 7-motor Replace and battery solar cover. panel. 0 min.. Battery pack replacement 7 5- Charging is finished when LED changes colour back to green. Disconnect charger from battery and from mains. 6- Reconnect battery to motor. 7- Replace battery cover. 5- Charging is finished when LED changes colour b - Disconnect battery pack, motor (a) a - Replace battery pack (c). with an identica 7 3- Charge new pack. Connect new pack
FY INSTRUCTIONS IS RTS REMOTE CONTROLS GLE FY INSTRUCTIONS & OPERATION FIVE CHANNEL INSTRUCTIONS s S RTS REMOTE CONTROLS UP 3 Telis RTS Pure STOP 33 LE Telis & 5 RTS FIVE Pure CHANNEL 39 Telis RTS Silver 4 Telis 5 RTS Silver Telis RTS Remote Controls Single and Five. DOWN UP 80643 Telis RTS Patio 80645 Telis 5 RTS Patio UP STOP DOWN Single PenVersion Previously programmed remote Pen Pen PROGRAMMING UP ADDING A NEW REMOTE OPERATING CHANNE Telis RTS A. Pure PROGRAMMING - ADDING STOP 50 Telis RTS Lounge A LED NEW REMOTE LED OPERATING STOP Lights 3 Telis 5 RTS Pure Programming Programming 5 Telis 5 CHANNEL RTS Lounge Indicator 9 Telis RTS Silver DOWN DOWN A previously programmed remote can be used Light in order to add a new remote or channel 43 Telis Telis 5 RTS RTS Silver Patio BACK VIEW 45 If a Telis Transmitter has not been previously programmed, please refer to installatio 0 Telis Telis 5 RTS RTS Lounge Patio LED A previously programmed remote can be used motorized in order window to add covering. Programming Telis 5 RTS Lounge Indicator Single a Five BACK Light 3 Telis RTS new Patioremote or channel to Motorized Version Window Covering. If a Version Fig. 5 Telis 5 RTS Patio Previously Telis Transmitter has not yet been previously programmed, please programmed remote Single Five BACK refer to installation instructions of Version relevant Adding a RTS Telis motorized RTS Transmitter Version only: Pen New Telis window covering.. Using previously programmed Telis remote to be added. Using new remote, press and hold programming briefly press th OGRAMMING ADDING A NEW REMOTE OPERATING Pen button CHANNEL on back of remote until button until th Programming window covering jogs. jogs. Windo viously. ADDING A TELIS RTS TRANSMITTER ONLY now learned t GRAMMING programmed ADDING remote can A be NEW used REMOTE in order to add OPERATING a new remote or CHANNEL channel to Motorized Window Covering. BACK VIEW Programming elis Transmitter has not been previously programmed, please refer to installation instructions of relevant RTS new Telis rized window a. Using covering. previously programmed Telis remote, press and hold BACK VIEW iously programmed remote can be used in order to add a new remote or channel to Motorized Window Covering. lis Transmitter programming has not been previously button programmed, on back of remote until Previously please refer to installation instructions of relevant Fig. RTS New Telis ized window window covering. covering jogs. (fig. ) programmed remote remote to be added g a Telis RTS Transmitter only: Pen Pen ing previously programmed Telis Previously. Using new Telis remote, New Telis b. Using new Telis remote, briefly press programming Previously mote, press and hold programming programmed remote briefly press programming remote to be programmed added remote tton a Telis on back button RTS of Transmitter remote until until only: window covering jogs. The Adding window a Telis covering Pen button until 5 RTS window Transmitter covering only: Previously Pen Programming ProgrammingPen indow g previously covering has now jogs. programmed learned Telis commands of programmed new. Telis Using. jogs. remote Using remote. Window new previously Telis covering (fig. remote, programmed ) has Telis. Using new ote, press and hold programming briefly now remote, learned press press programming commands hold of programming desired ch BACK VIEW Pen BACK VIEW ton on back of remote until button button new until Telis on back remote. window of remote covering until window SELECT BUT Programming Programming dow covering jogs. jogs. covering Window jogs. covering has Programming each time. ADDING A TELIS 5 RTS TRANSMITTER ONLY now learned commands of pressed, indic BACK VIEW BACK VIEW Programming new Telis remote. BACK VIEW a. Using previously programmed BACK VIEW Telis remote, press and hold Fig. 3 programming button on back of remote until Previously window covering jogs. (fig. 3) programmed remote New Telis 3. 5 Using Teli g a Pen remote to programming ing previously programmed Telis. Using new Telis 5 remote, select be added Previously b. Using new Telis 5 remote, select desired channel using window cove ote, press and hold programming programmed remote desired channel using CHANNEL Pen window cove tton a Telis on back 5 RTS of Transmitter CHANNEL remote until only: window SELECT BUTTON. (The led will SELECT illuminate BUTTON. (The each LED will illuminate Pen commands of vering g previously jogs. Programming time programmed Telis is pressed,. Using indicating each time new Telis 5 remote, select is ote, press and hold programming pressed, desired indicating channel using selected CHANNEL Programming ton on back selected of remote until channel. window(fig. BACK 4) VIEW SELECT BUTTON. (The LED will illuminate ering jogs. Programming each time is LED BACK Lights VIEW c. Using new Telis 5 remote, briefly press pressed, programming indicating selected BACK VIEW Fig. 4 New Telis 5 button until window covering jogs. The RTS motorized remote to be added window covering has now learned commands 3. Using Copyright of Telis Somfy 5 new remote, Systems, Telis briefly Inc. /00 press C-000 5 remote. (fig. 5) programming button until motorized New Pen Telis 5 remote to window covering jogs. The RTS motorized be added 3. Using window Telis covering 5 remote, has now briefly learned press PAGE REV 6 Programming programming commands of button new until Telis 5 motorized remote. Pen window covering jogs. The RTS motorized window covering has now learned commands of new Telis 5 remote. BACK VIEW Programming BACK VIEW yright Somfy Systems, Inc. /00 8 right Somfy Systems, Inc. /00 C-000 C-000 Fig. 5 PAGE REV 6 PAGE REV 6
OPERATION INSTRUCTIONS (continued) B. PROGRAMMING - SETTING A FAVITE POSITION (MY BUTTON) In addition to standard OPEN and CLOSE features, Telis remote enables user to pre-establish a favorite stop location. a.k.a. MY (stop) favorite An example could be to command RTS motorized window covering to a 50% or 75% open or closed position when MY button is briefly pressed.. TELIS RTS TRANSMITTER ONLY: a. Using UP ( ) or DOWN ( ) buttons, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( button to stop window covering once (fig. ) b. Press and hold MY ( ) button until window covering jogs. Favorite position is now recorded. (fig. ) c. Favorite MY ( ) position can be activated from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed (fig. 3). TELIS 5 RTS TRANSMITTER ONLY a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected (fig. 4) b. Using UP ( ) or DOWN ( ) buttons, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( button to stop window covering once (fig. 5) NOTE: Activating window covering to a favorite position while already in-motion will require two brief presses of MY - - Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. PLACING THE BATTERY ing a small screwdriver loosen ews on reverse side of remote ntrol and remove back cover. OGRAMMING - SETTING A FAVITE POSITION (MY). Press ans hold MY ( ) until window covering jogs. Favorite position is now recorded. RTS Transmitter only: ing UP ( ) or DOWN ( ) s, tivate window covering to a desired sition, for example halfway Open or osed. Briefly press MY ( tton to stop window covering ce dition to standard OPEN and CLOSE features, Telis remote enables user to pre-establish a favorite stop location. a.k.a. MY ite An example could be to command RTS motorized window covering to a 50% or 75% open or closed position n MY button is briefly pressed. 5 RTS Transmitter only: sing Telis 5 remote, select ppropriate channel using CHANNEL ELECT BUTTON. (The LED lights will lluminate each time utton is pressed, indicating selected hannel) sing UP ( ) or DOWN ( ) uttons, activate window covering o a desired position, for example alfway Open or Closed. Briefly ress MY ( o stop window covering once osition is reached. RTS Transmitter only: e UP ( ) or DOWN ( )s to en or close window covering. a specific position is necessary, iefly press MY ( tton to stop window covering ce. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed ERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. PLACING THE BATTERY ing a small screwdriver loosen OGRAMMING - SETTING A FAVITE POSITION (MY). Press ans hold MY ( ) until window covering jogs. Favorite position is now recorded. RTS Transmitter only: ing UP ( ) or DOWN ( ) s, tivate window covering to a desired sition, for example halfway Open or osed. Briefly press MY ( tton to stop window covering ce dition to standard OPEN and CLOSE features, Telis remote enables user to pre-establish a favorite stop location. a.k.a. MY ite An example could be to command RTS motorized window covering to a 50% or 75% open or closed position n MY button is briefly pressed. 5 RTS Transmitter only: sing Telis 5 remote, select ppropriate channel using CHANNEL ELECT BUTTON. (The LED lights will lluminate each time utton is pressed, indicating selected hannel) sing UP ( ) or DOWN ( ) uttons, activate window covering o a desired position, for example alfway Open or Closed. Briefly ress MY ( o stop window covering once osition is reached. RTS Transmitter only: e UP ( ) or DOWN ( )s to en or close window covering. a specific position is necessary, iefly press MY ( tton to stop window covering ce. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed ERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. NOTE: IN CASE OF A LOST TRANSMITTER, PROFESSIONAL PROGRAMMING ASSISTANCE IS REQUIRED. PLEASE CONTACT SOMFY AT somfytech@somfy.com YOUR LOCAL DEALER AT www.somfysystems.com/locatedealer. REPLACING THE BATTERY. Using a small screwdriver loosen screws on reverse side of remote control and remove back cover.. Replace battery with one 430 Lithium 3V battery. once C-000 Copyright SOMFY SYSTEMS, INC. /00 PAGE R a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed OPERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. NOTE: IN CASE OF A LOST TRANSMITTER, PROFESSIONAL PROGRAMMING ASSISTANCE IS REQUIRED. PLEASE CONTACT SOMFY AT somfytech@somfy.com YOUR LOCAL DEALER AT www.somfysystems.com/locatedealer. REPLACING THE BATTERY. Using a small screwdriver loosen screws on reverse side of remote control and remove back cover.. Replace battery with one 430 Lithium 3V battery. once C-000 Copyright SOMFY SYSTEMS, INC. /00 P a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed OPERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. NOTE: IN CASE OF A LOST TRANSMITTER, PROFESSIONAL PROGRAMMING ASSISTANCE IS REQUIRED. PLEASE CONTACT SOMFY AT somfytech@somfy.com YOUR LOCAL DEALER AT www.somfysystems.com/locatedealer. REPLACING THE BATTERY. Using a small screwdriver loosen screws on reverse side of remote control and remove back cover.. Replace battery with one 430 Lithium 3V battery. once C-000 Copyright SOMFY SYSTEMS, INC. /00 a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed OPERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. NOTE: IN CASE OF A LOST TRANSMITTER, PROFESSIONAL PROGRAMMING ASSISTANCE IS REQUIRED. PLEASE CONTACT SOMFY AT somfytech@somfy.com YOUR LOCAL DEALER AT www.somfysystems.com/locatedealer. REPLACING THE BATTERY. Using a small screwdriver loosen screws on reverse side of remote control and remove back cover.. Replace battery with one 430 Lithium 3V battery. window covering jogs. Favorite position is now recorded.. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( once C-000 Copyright SOMFY SYSTEMS, INC. /00 PAGE a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed OPERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. NOTE: IN CASE OF A LOST TRANSMITTER, PROFESSIONAL PROGRAMMING ASSISTANCE IS REQUIRED. AT somfytech@somfy.com YOUR LOCAL DEALER AT www.somfysystems.com/locatedealer. REPLACING THE BATTERY. Using a small screwdriver loosen screws on reverse side of remote control and remove back cover.. Replace battery with one 430 Lithium 3V battery.. Press ans hold th window covering now recorded. Telis RTS Transmitter only:. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( once C-000 Copyright SOMFY SYSTEMS, INC. /00 In addition to standard OPEN and CLOSE features, Telis remote enables user to pre-e favorite An example could be to command RTS motorized window covering to when MY button is briefly pressed. a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once Telis 5 RTS Transmit. Using Telis 5 appropriate c CHANNEL SELECTO lights will illumin indicating se. Using UP ( s to open window coverin position is neces MY (stop) stop window position is reach m 3. Favorite MY ( from any previou Example: Briefly while window c OPERATING THE MOTIZED WINDOW COVERING Note: Activatin Favorite positio will require tw Window coveri (Stopped) posit position can be NOTE: IN CASE OF A LOST TRANSMITTER, PROFESSIONAL PROGRAMMING ASSISTANCE IS REQUIRED. PLEASE CONTACT SOMFY AT somfytech@somfy.com YOUR LOCAL DEALER AT www.somfysystems.com/locatedealer. REPLACING THE BATTERY. Using a small screwdriver loosen screws on reverse side of remote control and remove back cover.. Replace battery with one 430 Lithium 3V battery.. Press ans hold MY ( ) until window covering jogs. Favorite position is now recorded. Telis RTS Transmitter only:. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( once C-000 Copyright SOMFY SYSTEMS, INC. /00 PAGE REV 6 when MY button is briefly pressed. a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed OPERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. PROGRAMMING - SETTING A FAVITE POSITION (MY). Press ans window now reco Telis RTS Transmitter only:. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( once In addition to standard OPEN and CLOSE features, Telis remote enables user t favorite An example could be to command RTS motorized window cov when MY button is briefly pressed. a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once Telis 5 RTS T. Using appr CHANNEL lights wil indicatin 3. Favorite from any Example while w position OPERATING THE MOTIZED WINDOW COVERING Note: A Favorite will req (stop) b Window (Stoppe position REPLACING THE BATTERY PROGRAMMING - SETTING A FAVITE POSITION (MY). Press ans hold MY ( ) until window covering jogs. Favorite position is now recorded. Telis RTS Transmitter only:. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( once In addition to standard OPEN and CLOSE features, Telis remote enables user to pre-establish a favorite stop location. a. favorite An example could be to command RTS motorized window covering to a 50% or 75% open or closed pos when MY button is briefly pressed. a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once LED Lig from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed OPERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. REPLACING THE BATTERY PROGRAMMING - SETTING A FAVITE POSITION (MY). Press ans hold MY ( ) until window covering jogs. Favorite position is now recorded. Telis RTS Transmitter only:. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( once In addition to standard OPEN and CLOSE features, Telis remote enables user to pre-establish a favorite stop location. a.k.a. MY favorite An example could be to command RTS motorized window covering to a 50% or 75% open or closed position when MY button is briefly pressed. a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed OPERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. REPLACING THE BATTERY PROGRAMMING - SETTING A FAVITE POSITION (MY). Press ans hold MY ( ) until window covering jogs. Favorite position is now recorded. Telis RTS Transmitter only:. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( once In addition to standard OPEN and CLOSE features, Telis remote enables user to pre-establish a favorite stop location. a.k.a. favorite An example could be to command RTS motorized window covering to a 50% or 75% open or closed position when MY button is briefly pressed. a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. briefly press MY ( once. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected. Using UP ( ) or DOWN ( ) s to open or close window covering. If a specific position is necessary, briefly press MY (stop) ( ) to stop window covering once from any previous window covering Example: Briefly press MY ( ) button while window coverings in a Open or Closed OPERATING THE MOTIZED WINDOW COVERING Note: Activating window covering to a Favorite position while already in-motion will require two brief presses of MY Window covering MUST BE in a stationary (Stopped) position before MY favorite position can be activated. PROGRAMMING - SETTING A FAVITE POSITION (MY). Press ans hold window cove now recorded Telis RTS Transmitter only:. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example halfway Open or Closed. Briefly press MY ( once In addition to standard OPEN and CLOSE features, Telis remote enables user to pr favorite An example could be to command RTS motorized window coverin when MY button is briefly pressed. a. Using Telis 5 remote, select appropriate channel using CHANNEL SELECT BUTTON. (The LED lights will illuminate each time is pressed, indicating selected b. Using UP ( ) or DOWN ( ) s, activate window covering to a desired position, for example press MY ( to stop window covering once Telis RTS Transmitter only:. Use UP ( ) or DOWN ( )s to open or close window covering. Telis 5 RTS Trans. Using Teli appropria CHANNEL SELE 3. Favorite MY from any pre Example: Bri while windo OPERATING THE MOTIZED WINDOW COVERING Note: Activ Favorite pos will require (stop) butto Window cov (Stopped) p position can Fig. Fig. Fig. 3 Fig. 4 Fig. 5 9