FederationofMalysia EDICTOFGOVERNMENT± Inordertopromotepubliceducationandpublicsafety,equal justiceforal,abeterinformedcitizenry,theruleoflaw, worldtradeandworldpeace,thislegaldocumentishereby madeavailableonanoncommercialbasis,asitistherightof alhumanstoknowandspeakthelawsthatgovernthem. MS 239 (1987) (English): SPECIFICATION FOR COCONUT OIL (FIRST REVISION)
MALAYSIAN STANDARD MS 239 : 1987 SPECIFICATION FOR COCONUT OIL ( FIRST REVISION ) SI RI M ST.ANDARDS STANDARDS & INDUSTRIAL RESEARCH INSTITUTE OF OF MALAYSIA Copyright Copyright
SIRIM.. No part of this publication may be photocopied or otherwise reproduced without the prior permission in writing of SIRIM
MS 239 : 1987 This Malaysian Standard, which had been approved by the Food and Agricultural Industry Standards Committee and endorsed by the Council of the Standards and Industrial Research Institute of Malaysia (SIRIM) was published under the authority of the SIRIM Council in November, 1987, 1987. SIRIM wishes to draw attention to the fact that this Malaysian Standard does not purport to include all the necessary provisions of a contract. The Malaysian Standards are subject to periodical review rev1ew to keep abreast of progress in the industries concerned. concerned, Suggestion for improvements will be recorded and in due course brought to the notice of the Committees charged with the revision of the standards to which they refer. The following references relate to the work on this standard: Committee reference SIRIM'401/2/9 Draft for comment D99 (ISC A)R Amendments issued since publication ---------,-----------------.-------_. ---------,-----------------.------_..-.------------...------------..------- Amd. Amd, No Date of issue Text affected ---------'------------------------_._----------- ---------'-------------------------------------
!VIS MS 239 : 1987 CONTENTS Page Page Committee representation Foreword Scope 2 Definitions 3 Grades 4 Requirements 5 Packing 6 Labelling 7 Legal requirements 8 Sampling and testing 9 Compliance Table 1 Requirements for coconut oil 3 4 5 5 5 5 6 6 7 7 7 6 2
II/iS rvis 239 1987 Committee representation The Food and Agricultural Industry Standards Committee under whose supervision this Malaysian Standard was prepared, comprises representatives from the following Government Ministries, trade, commerce and manufacturer associations and scientific and professional bodies. Federal Agricultural Marketing Authority Federation of Malaysian Consumers Association Federation of Malaysian Manufacturers Malaysian Agricultural Research and Development Institute Ministry of Agriculture (Agriculture Department) National Chambers of Commerce and Industry of Malaysia Oil Palm Growers' Council of Malaysia Rubber Producers' Council of Malaysia Rubber Research Institute of Malaysia Universiti Pertanian Malaysia The Technical Committee on Vegetable Oils and Oleaginous Products which prepared this Malaysian Standard consists of the following representatives: Encik S. Krishnan (Chairman) Encik VeJayuthan Velayuthan Encik Tang Loon Boon/ Encik N. Saravanan Encik Yong Y Moh Lim/ Encik Peng Chik Dr. Lim Pang Honl Hon/ Encik Yee Kuan Hing Encik K. Berger/ I Encik T.P. Pantzarisl Pantzaris/ Puan Slew Siew Wai Lin Encik Phang Kwong Thinl Thin/ Encik Low Thing Encik Adinan Husinl Husin/ Puan A.H.G Chin Encik Abdul Rahman Jaafarl Jaafar/ Encik Wazir Haron Encik Ti Thiow Heel Hee/ Puan Maharam Jusoh Encik Aziz Zakarial Zakaria/ Y.M. Raja Zainal Sulaiman Encik Mohd Salleh Mohd Kassiml Kassim/ Encik Wong Soo Khwan Encik Tang Thin Sue/ Encik Joseph Moolayil Encik Muk Mun Tat (co-opted member) Puan Puziah Hashim Puan Soh Swee Keng/ Puan Saleha A. Jalil (Secretary ) Incorporated Society of Planters Federal Agricultural Marketing Authority Federal Land Development Authority Federation of Malaysian Manufacturers Palm on Oil Research Institute of Malaysia Malayan Edible Oil Manufacturers, Association Malaysian Agriculture Research and Development Institute (Food Technology Division) Ministry of Primary Industries Chemistry Department Malaysian Oil Palm Growers' Council Palm Oil Registration and Licensing Authority Palm Oil Refiners Association of Malaysia Socfin Co. Bhd. Standards and Industrial Research Institute of Malaysia 3
MS 239: : 1987 FOREWORD This Malaysian Standard was prepared by the Technical Committee on Vegetable Oils and Oleaginous Products under the authority of the Food and Agricultural Industry Standards Committee. This revised Malaysian Standard supersedes MS 239 : 1974, 'Specification for coconut oil'. In the preparation of this standard, the following publications were referred to: (a) British Standard BS 628 : 1967, 'Specification for crude coconut oil' (b) Indian Standard IS : 542-1963, 'Specification for coconut oil (Revised), (c) Philippines Trade Standard 412-07.01 other purposes' 1968, 'Standardisation of crude coconut oil and for 4
1\!~S MS 239 :; 1987 SPECIFICATION FOR COCONUT OIL (FIRST REVISION) 1. L SCOPE L] 1.1 This Malaysian Standard prescribes the requirements for coconut oil 2. DEFINITIONS For the purpose of this standard, the following definitions shall apply: 2.1 Crude coconut is the product obtained by expression and/or solvent extraction from the kernel (copra) of the coconut,. Cocos flucijera, llucijera, and shall be free from admixture with other oils and fats. 2.2 Refined coconut oil is obtained from crude coconut oil which has been refined by neutralization with alkali, bleached with bleaching earth or activated carbon or both the deodorised with steam; no other chemical agents being used. 3. GRADES 3.1 Coconut oil shall be of the following foliowing grades: 3.1.1 3,1.1 Crude 3.1.1.1 Grade 3.1.1.2 Grade 2 3.1.2 Refined grade The refined grade, grade 1 and grade 2 are edible grades and do not require further processing. 4. REQUIREMENTS 4.1 Description. Coconut oil shall be the wholesome oil extracted from the fruit of Cocos flucijera. nucifera. It shall be clear and free from rancidity, adulterants including mineral oil, sediment, suspended and other foreign matter and separated water. 5
MS 239 : 1987 4.2 Coconut oil may contain food conditioner and antioxidant as permitted by the Food Regulations. 4.3 Clarity. The clarity of coconut oil shall be such that there shall be absence of turbidity after keeping the filtered sample at 30 C for 24 hours. 4.4 Admixture with other oils. Coconut oil shall be free from admixture with other oils. 4.5 Coconut oil shall also comply with the requirements prescribed in table L 1. Table 1. Requirements for coconut oil ~ Requirements _ Item no. 1'"'. Characteristics Crude Grade 1 Grade 2 in irefined -" -- _.._--- -_._.- 1. l. Free fatty adds, acids, calculated as lauric add, acid, % by mass, max. 1.0 3.5 0.1 2. Moisture and insoluble impurities, % by mass, max. 0.50 0.50 0.10 3. Iodine value (Wijs) 1.5 7.5 to 10.5 1.5 7.5 to 10.5 1.5 7.5 to 10.5 4. Colour in a 133.35 mm (5.25 in) cell on the! Lovibond tintometer scale, max. 3R 4R l.5r 1.5R 5. Refractive index at 40 C 1.4480 to 1,4480 1.4480 to 1.4480 to l.4490 1.4490 1.4490 1.4490 6. Specific gravity at 30 C/30 C 0.915 to 0.915 to 0.915 to g:bi~ to 0.920 0.920 0.920 '" 1. 7. Saponification value, mg KOH/g g 248 to 264 248 to 264 248 to 264 8. Unsaponifiable matter, % by mass, max..., 0.8 0.8 0.5 ---! 5. PACKING 5.1 Coconut oil, crude or refined, shall be supplied in suitable well-closed containers, as agreed upon between the purchaser and the supplier. 5.2 Bulk shipment. Coconut oil, crude or refined, in bulk shall be shipped in vessel deeptanks or wingtanks with steam coils, in tank-trucks, in lighters or other appropriate containers. 6. LABELLING 6.1 The containers shall be labelled with the following information: 6.1.1 Name and grade of the product; 6
MS MS 239 239 : 1 1987 6.1.2 Weight of the product; 6.1.3 Producer's name or trade-mark; 6.1.4 Month and year of manufacture or code; 6.1.5 Expiry date marking; 6.1.6 Country of origin. 6.2 Each container may, by arrangement with with the the Standards and and Industrial Research Institute of of Malaysia be marked with the Certification Mark of of SIRIM, provided the the product conforms to the requirements of this standard. 7. LEGAL A L REQUIREMENTS 7.1 7.1 The product shall in au all other aspects comply with the the requirements of the the legislations currently enforced in the country. 8. SAMPLING AND TESTING 'festing 8.1 Representative samples of the coconut oil oj! shall be drawn as prescribed in III MS 252, 'Methods of sampling and test for oils and fats'. 8.2 Tests shall be carried out as prescribed in MS 252, 'Methods of sampling and test for oils and fats'. 9. COMPLIANCE 9.1 If on testing, each of the samples is is found to conform to the requirements specified in in this standard, the lot, batch or consignment from which the samples have been drawn shah be deemed to comply with this standard. In this context, the term 'sample' shall be taken to include also 'Composite sample or samples' samples" where appropriate as agreed upon mutually between seller and buyer. 7 '7
TANDA-TANDA STANDARD SIRIM Tanda-tanda Standard SIRIM M seperti yang tertera di bawah adalah tanda-tanda pengesahan dagangan berdaftar. Tanda-tanda ini hanya boleh digunakan oleh mereka yang dilesenkan di bawah skim tanda pengesahan yang dijalankan oleh SIRIM IM mengikut nombor Standard Malaysia yang berkaitan.. Kewujudan tanda-tanda ini pada a atau berkaitan dengan sesuatu barangan adalah sebagai jaminan bahawa barangan tersebut telah dikeluarkan melalui satu sistem penyeliaan, kawalan dan ujian, yang dijalankan semasa pengeluaran. Ini termasuk pemeriksaan berkala kerja-kerja pengeluar menurut skim tanda pengesahan SIRIM yang dibentuk untuk menentukan bahawa barangan tersebut menepati Standard Malaysia. Keterangan-keterangan lanjut mengenai syarat-syarat lesen boleh didapati dari: : Ketua Pengarah, Institut Standard dan Penyelidikan Perindustrian Malaysia, Persiaran Dato' Menteri,, Seksyen 2, Peti Surat 7035, 40911 Shah Alam, Selangor. IVIS SIRIM STANDARD MARKS The SIRIM Standard Marks shown above are registered certification trade marks. They may be used only by those licensed under the certification marking scheme operated by SIRIM and in conjunction with the relevant Malaysian Standard number. The presence of these Marks on or in relation to a product is an assurance that the goods have been produced under a system of supervision, control and testing, operated during production, and including periodical inspection of the producer's works in accordance with the certification marking scheme of SIRIM designed to ensure compliance with a Malaysian Standard. Further particulars of the terms of licence may be obtained from: : Director-General, Director-General, Standards Standards and and Industrial Industrial Research Research Institute Institute of of Malaysia, Malaysia, Persiaran Persiaran Dato' Dato' Menteri, Menteri, Section Section 2, 2, P.O. P.O. Box Box 7035, 7035, 40911 4091 1 Shah Shah Alam, Alam, Selangor. Selangor. Dicetak Dicetak dan dan diterbitkan diterbitkan oleh: oleh: Institut Institut Standard Standard dan dan Penyelidikan Penyelidikan Perindustrian Perindustrian Malaysia. Malaysia. Printed Printed and and Published Published by by: : Standards Standards and and Industrial Industrial Research Research Institute Institute of of Malaysia. Malaysia.
INSTITUT STANDARD DAN PENYELIDIKAN PERINDUSTRIAN MALAYSIA Institut Standard dan Penyelidikan Perindustrian Malaysia (SIRIM)) telah ditubuhkan hasil dari cantu man Institut Piawaian Malaysia (SIM) dengan Institut Negara bagi Penyelidikan Sains dan Perusahaan (NISIR) di bawah Undang-Undang Malaysia Akta 157 pada 16hb. September, 1975: Akta Institut Standard dan Penyelidikan Pe,industrian Perindustrian Malaysia (Perbadanan)1975. Institut ini diletakhak dengan kuasa untuk memaju memaju dan menjalankan penyelidikan perindustrian dan untuk menyedia dan memajukan standard-standard bagi barangan-barangan, proses-proses, amalan-amalan dan perkhidmatan-perkhidmatan; ; dan bagi mengadakan peruntukan bagi perkara-perkara yang bersampingan atau au berkaitan dengan maksud-maksud itu. Satu daripada tugas-tugas Institut ini adalah menyediakan Standard-Standard Malaysia dalam bentuk penentuanpenentuan bagi bahan-bahan, keluaran-keluaran luaran-keluaran,, kaedah-kaedah ujian, kod-kod amalan yang sempurna dan selamat, sistem penamaan,, dll.. Standard-Standard Malaysia disediakan oleh jawatankuasa-jawatankuasa perwakilan yang menyelaras keupayaan pengilangan dan kecekapan pengeluaran dengan kehendak-kehendak yang munasabah dari pengguna. la menuju ke arah mencapai kesesuaian bagi maksud, memudahkan pengeluaran dan pengedaran, kebolehsalingtukaran gantian dan pelbagai pilihan yang mencukupi tanpa pembaziran. Standard-Standard Malaysia disediakan hanya setelah penyiasatan yang lengkap menunjukkan bahawa awa sesuatu projek itu disahkan sebagai yang dikehendaki dan berpadanan dengan usaha yang terlibat. Hasil ini berasaskan persetujuan sukarela, dan memberi pertimbangan kepada kepentingan pengeluar dan pengguna. Standard-Standard Malaysia adalah sukarela kecuali ia dimestikan oleh badan-badan berkuasa melalui peraturan-peraturan, undang-undang persekutuan dan tempatan atau cara-cara lain yang sepertinya. Institut ini beroperasi semata-mata berasaskan tanpa keuntungan. la adalah satu badan yang menerima bantuan kewangan dari Kerajaan,, kumpulan wang dari bayaran keahlian,, hasil dari jualan Standard-Standard dan terbitan-terbitan lain, bayaran-bayaran ujian dan bayaran-bayaran lesen untuk mengguna Tanda Pengesahan SIRIM dan kegiatan-kegiatan lain yang berhubung dengan Penstandardan, Penyelidikan Perindustrian dan Khidmat Perunding. STANDARDS AND INDUSTRIAL RESEARCH INSTITUTE OF MALAYSIA The Standards and Industrial Research Institute of Malaysia (SIRIM) is established with the merger of the Standards Institution of Malaysia (SIM) and the National Institute for Scientific and Industrial Research (NISIR) under the Laws of Malaysia Act 157 on 16th September, 1975: Standards and Industrial Research Institute of Malaysia (Incorporation) Act 1975. The Institute is vested with the power to provide for the promotion and undertaking of industrial research and for the preparation and promotion of standards for commodities, processes, practices and services; and to provide for r matters incidental to or connected with those purposes. One of the functions of the Institute is to prepare Malaysian Standards in the form of specifications for materials and products, methods of testing,, codes of sound and safe practice, nomenclature, etc. Malaysian Standards are prepared by representative committees which co-ordinate manufacturing capacity and production efficiency with the user's reasonable needs. They seek to achieve fitness for purpose, simplified production and distribution,, replacement interchangeability, and adequate variety of choice without wasteful l diversity. Malaysian Standards are prepared only after a full enquiry has shown that the project is endorsed as a desirable one and worth the effort involved. The work is based on voluntary agreement, and recognition of the community of interest of producer and consumer. The e use of Malaysian Standards is voluntary except in so far as they are made mandatory by statutory authorities by means of regulations, federal and local by-laws or any other similar ways.. The Institute operates entirely on a non-profit t basis.. It is a grant aided body receiving financial aid from the Government, funds from membership subscriptions and proceeds from sales of Standards and other publications, testing fees s and licence fees for the use of SIRIM Certification Mark and other activities associated With with Standardization ization,, Industrial Research and Consultancy Services.