ALIGN BORE MAINS DECK CYLINDER SURFACE 911-930 395.00 (head studs must be removed) 356-912 275.00 911-930 150.00 Thrust Cut 4 Cylinder 195.00 356-912 130.00 Inspection of Case 95.00 Remove Head Studs 80.00 min. Check Align Bore 95.00 SURFACE CASE HALVES BORE CASE FOR LARGER CYLINDER BORE BACK TO STD. (head studs must be removed) 911 2.0 2.7 795.00 911-930 260.00 930 964 850.00 930 for 3.8 Ltr with O Ring 700.00 356-912 650.00 912 180.00 Weld 356-912 1200.00 930-993 O Rings 300.00 CYLINDER HEAD STUD OIL SYSTEM INSERTS (+ INSERTS) 911-930 R&R Oil Plugs And Clean Oil Galleys 195.00 Remove broken head studs 80.00 ea. 912 Timing Cover for Full Remove head studs 80.00 min. Flow Oil Filter 105.00 Remove time-serts or heli coils 80.00 min. 912 Oil Pump Cover for Full 911 Mag. Case 390.00 Flow Oil Filter 105.00 Aluminum Case 415.00 911 Oil By-Pass Modification, Spot Face Thru Bolt Holes 160.00 includes update kit 175.00 356-912 Repair Crack at Oil Cooler 395.00 Clear 911 Case for Larger Oil Pump 95.00 SHUFFLE PINS 912 R&R Oil Plugs 180.00 911 930 475.00 By-Pass Kit only 65.00 OIL SQUIRTERS (with squirters) PRESSURE TEST & CLEAN OIL COOLERS 911 440.00 911 930 140.00 356-912 330.00 356 912 140.00 Clean Squirters 50.00 Squirters 20.00 ea. WINDAGE RELIEF Boat Tail Mains 375.00 Moon Cut Cylinders 140.00 HOT TANK CASE Knife Edge Crank Shaft 350.00 For machining only all cases 40.00 Polish Main Webbing: Extra Cleaning 75.00 Mag Case 500.00 Aluminum Case 700.00 PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. Page: 1
RACE PREP WORK Shuffle Pin 475.00 Boat Tail Mains 375.00 Moon Cyl. Bottoms 140.00 Knife Edge Crankshaft 350.00 Lighten Counter Shaft 310.00 Lighten Flywheel (RSR) 250.00 Polish Main Webbing: Mag. Case 500.00 Aluminum Case 700.00 CONVERT EARLY ALUMINUM CASE TO 2.7 Bore for 2.7 Cylinders 260.00 Install Fuel Injection Bracket 280.00 Update to Late Chain Housings 240.00 Bore Case for Late Distributor 290.00 Machine Late Dist. To Fit Early Case 150.00 Modify Case for 2.7 Inter. Shaft 450.00 Oil Bypass Modification with Kit 175.00 Oil Squirters with Squirters 440.00 Clear Case for Larger Oil Pump 95.00 Shuffle Pin 475.00 Boat Tail Mains 375.00 Bore Early Mag Case for Shaft Brg. 220.00 SLEEVE CYLINDERS Sleeve Case (Full Sleeve) 2500.00 Sleeve Case (Half Sleeve) 1500.00 Sleeve Cylinder #3 500.00 PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. Page: 2
911 CRANKSHAFT WORK Grind Rods & Mains 325.00 Grind Rods OR Mains 225.00 Micropolish 60.00 Magna Flux 60.00 Heat Treat (Tuftrite) 275.00 Dowell Pulley to Crank 130.00 Weld & Grind Thrust 250.00 Pre-Grind and Weld 1 Journal 275.00 R & R Oil Plugs and Clean Crank 210.00 R & R Gears 25.00 Straighten 125.00 Knife Edge 350.00 Groove and Cross Drill 225.00 Balance 55.00 356 912 CRANKSHAFT WORK Grind Rods & Mains 275.00 Grind Rods OR Mains 200.00 Micropolish 60.00 Magna Flux 60.00 Heat Treat (Tuftrite) 275.00 Pre-Grind and Weld 1 Journal 275.00 R & R Oil Plugs and Clean Crank 120.00 R & R Gears 25.00 Straighten 125.00 Notch Oil Holes 60.00 Balance 55.00 REBUILD CONNECTING RODS (+ BUSHINGS) 911-912-356 25.00 ea. Carrillo Rods 50.00 ea. Magna Flux 30.00 Set Polish 40.00 ea. Lighten 30.00 ea. Offset Pin Bushings 250.00 Set Convert 22mm to 23mm 75.00 Set Convert 23mm to 22mm 75.00 Set Balance 55.00 Set Bushings 6.00 ea. PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. Page: 3
BALANCING 911, 930, 912, 356 PISTONS Complete 210.00 Bevel Tops 25.00 ea. Crankshaft 55.00 Valve Pockets 25.00 ea. Rods 55.00 Set Hone Pin Bores 13.00 ea. Pistons 55.00 Set Clean & Bead Blast 20.00 ea. Flywheel 55.00 Bore for Larger Pin 270.00 Set Pressure Plate 55.00 Machine Skirts for Crankshaft Pulley 15.00 Clearance 20.00 ea. Inspect Pistons & Cylinders 50.00 Set REFACE FLYWHEELS CYLINDER WORK 911 912 930 356 85.00 Bore Cast Iron for Oversize Piston 70.00 ea. Hone Cast Iron (Deglaze) 15.00 ea. Hone Nikasil (Deglaze) 25.00 ea. LIGHTEN FLYWHEELS Hone Alusil (Recondition) 45.00 ea. 911 930 RSR Style 250.00 Machine Tops of Cylinders 30.00 ea. 356 912 200.00 Machine Gasket Groove Deeper 40.00 ea. Machine Bottoms of Cylinder 30.00 ea. Moon Cylinder Bottoms 110.00 Set Bead Blast Cylinders 12.00 ea. INSTALL RING GEARS INCLUDES RING GEAR (6 OR 12 VOLT) 911 912 356 185.00 PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. Page: 4
PRECISION 3 ANGLE VALVE JOB INTAKE AND EXHAUST GUIDE LABOR 911-930 360.00 Set 911-930 912 356 15.00 ea 356-912 360.00 PR 993 20.00 ea Grind Seats Only 12.00 ea Guides 6.00 ea Grind Valves Only 12.00 ea RESURFACE HEADS BEVEL HEADS FOR PISTON CLEARANCE 911-930 220.00 Set 911-930 90.00 Set 356-912 150.00 PR 912-356 80.00 Set 930 Turbo Heads must have intake studs removed. $15.00 charge to remove studs. Not responsible for broken or damaged studs. BORE HEADS FOR LARGER CYLINDER 911 930 300.00 Set 356 912 200.00 Set EXHAUST STUD REPAIR FLY CUT CHAIN HOUSINGS 911-930 15.00 ea 911 930 75.00 PR 356-912 15.00 ea Remove Broken Drill or EZ Out min 150.00 ea SEAT REPLACEMENTS Weld Damaged Stud Hole min 45.00 ea 911-930 60.00 ea 23mm Stud 1.00 ea 912-356 60.00 ea 32mm Stud 4.00 ea Oversize Seats 15.00 ea Valve Seats 12.00 ea SPARK PLUG REPAIR Drill & Tap for Time Sert or Heli Coil Repair Cracked Plug Hole: 356-912 25.00 ea 400.00 ea PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. Page: 5
PORT & POLISH HEADS ALLOW 3 WEEKS LEAD TIME 911, 930, 964, 993 1200.00 Set 912 356 700.00 Set Reshape 912 356 Chambers 300.00 Set 911 2.0 Ltr to S Specs 1200.00 Set Custom Port and Polish Your Heads Call for to your Sample or Idea. Quote. PORTING & POLISHING INTAKE MANIFOLDS 911 Runners (6) 250.00 911 Carb Manifolds 300.00 PR 911 Throttle Bodies 300.00 PR 930 Turbo Plenum 150.00 930 Intermediate Blocks (6) Plastic 120.00 930 Intermediate Blocks (6) Aluminum 180.00 912 Intake Manifolds 250.00 PR Bore & Port Magnesium Stacks 750.00 PR Weld CIS Injector Cutout Area and Remachine 250.00 Set Drill & Tap for Mech. Injection 120.00 Set TWIN PLUG HEADS INCLUDES VALVE COVERS (at time of Head Twin Plugging) 911 930 375.00 3.6 3.8 Turbo Heads 400.00 912 356 10mm Plug 500.00 Valve Covers Only 50.00 PR PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. Page: 6
ROCKER ARMS 6 CYLINDER ROCKER ARM ADJUSTERS MUST BE REMOVED FOR GRINDING $25.00 Charge to Remove Adjusters Regrind 356 912 Weld 356 912 Regrind 911 Rebush 911 Regrind 993 Rocker Arms Polish Rocker Shafts Bushings 120.00 Set 20.00 ea 150.00 Set 150.00 Set 175.00 Set 24.00 Set 6.00 ea 356 912 LIFTERS AND OIL PUMP Regrind 356 912 Lifters (8) 120.00 Repair Oil Pump Drive Gear 80.00 Full Flow Oil Pump Cover 105.00 CAM TOWERS Remove and Clean Oil Tube 45.00 ea Clean & Hot Tank 65.00 PR Clean & Decarbonize 993 95.00 PR Surface 35.00 PR Surface Valve Covers 12.00 ea Bead Blast & Clean Valve Covers* 15.00 ea *Does not remove powder coating. Surface Cam Tower Valve Cover Area 100.00 PR FLY CUT CHAIN HOUSINGS 911 930 75.00 PR PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. Page: 7
MEDIA TUMBLE AND CLEAN PARTS 356 912 Case with Cover includes R-R Oil Plugs, Clean Oil Galleys, Hot Tank 340.00 911 993 Case includes R-R Oil Plugs, Clean Oil Galleys and Squirters, Hot Tank 405.00 Cam Towers includes Cleaning Oil Spray Bar 85.00 ea Chain Boxes 25.00 PR Chain Box Covers 15.00 PR Valve Covers (does not remove paint or powder coating) 15.00 ea Fan 20.00 Fan Housing 25.00 356 912 Intake Manifolds 25.00 PR 356 912 Generator Stand 15.00 911 Heads 15.00 ea 356 912 Heads 25.00 ea PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. Page: 8