MEGATON otor/stator Dispersing Technology MEGATON System MT 5000 In-line Processor for Laboratory, Pilot Plant and Production Dispersing and Mixing Technolgy
MEGATON System MT 5000 - Multipurpose Pilot Plant Small Quantities In-Line MEGATON processors are installed in-line of the product stream. The product can be treated in a single pass for true in-line work or may be recirculated for an alternative way of batch processing. The main advantage of the MEGATON System MT 5000 pilot plant ist the possibility of simulating later production on a laboratory scale. These tests can be done with a minimum amount of product and energy. It is also possible to use the MT 5000 as an industrial processor for small quantities. High Power and Continuous Operation powerful and efficient drive unit with 1500/1300 Watt maintenance-free 3-phase motor is controlled via a special frequency controller; connection to a standard single phase wall socket is sufficient speed is infinitely variable between 5000 and up to 20000 rpm up to approx. 40 m/s tip speed without load; max. rpm values depend on the chosen dispersing aggregate and product properties quiet drive system approx. 62 db A (without load) digital display for speed indication different and interchangeable dispersing generators (otor/stator) connection for programmable ECO control unit max. troughputs of up to 4000 l/h possible, depend on dispersing generator and product properties MT 5000 with ECO P 502 and Circulation System The MEGATON MT 5000 otor/stator Homogenizer disperses, emulsifies and reduces the size of solid particles, droplets and gas bubbles to a few microns or less. It chops, grinds, mixes and blends large amounts of product in a more economical, faster and better way than any other device. High Flexibility The ideal processor configuration is selected from a choice of four different working chambers and four dispersing generators. Working chambers are available with cooling/heating jackets (MTK) or without (MTO). The same applies for the optional available circulating tubes and vessels. For pharmaceutical applications, a special sterile version, FDA approced, is available. A new style single mechanical seal is used in the working chamber which is cooled and lubricated by the product. It offers three benefits: No need for water cooling No product contamination by the seal flush Working pressures up to 50 bar are possible There are also versions which offer the possibility of connecting a non-pressure back-up cooling quench (Q = Quench) as a fail-safe option. The rotor/stator shear generators are designed for efficiency and longevity. The rows of teeth are thicker for strength, gaps between rotor and stator are narrower for higher shear. An ongoing research cooperation with the Swiss Federal Technical Institute provides new and improved generator designs and geometries for specific and standard applications. The combination of high tip speed of the rotor and the specific design of the entire generator, result in higher shear forces and greater throughput. MT 5000 Dispersing Generators Indicative Troughput Table PM 10000 15000 17000 20000 Generator l/h gpm l/h gpm l/h gpm l/h gpm MTG 36/2 1800 8 2500 11 3500 15 3600 16 MTG 36/4 1200 5 1800 8 2200 10 - - MTG 48/2 2500 11 3800 17 4200 18 - - MTG 48/6 1400 6 1800 8 1900 8 - - The indicated values are related to water.
MEGATON - Small Industrial Processors Programmed to be Succesful In combination with the electronic programming unit, model ECO P 502, all important parameters such as speed, working time and maximum temperature can be selected and monitored. Five different program sets can be permanently stored and recalled for routine work under identical conditions. This worthwile option also allows the connection of the MEGATON System MT 5000 to a computer via a S 232 interface. A control software program is optionally available and allows to experiment with additional parameters. Complete In-Line Systems - Your Small Processing Plant The real benefit of a homogenizer is given when it is offered as a complete working system which includes all necessary peripherical accessories. We can complete your MT 5000 with circulating tubes and working tanks. These items can be chosen from our standard program. They are available as complete sets made of glass or stainless steel, with or without water jackets. They can also be built according to your specific requirements, e.g. for working under pressure. Superb Swiss workmanship gives you precision parts with the surface finish required in the food and pharmaceutical industries. We shall be glad to send you our applications questionnaire which covers all important points. Certain applications, e.g. chemical reactions, can only be accomplished successfully if the components are mixed right inside the generator. This is possible by adding a manifold which allows injecting of fluids or gas straight into the center of the generator. This prevents the single components coming into contact with each other and therefore eliminates the risk of pipe blocking and any uncontrolled reaction. The right MEGATON Dispersing Generator for your task Generator Technical Data MTG 36/2 MTG 36/4 MTG 48/2 MTG 48/6 Stator-Ø 36 mm 36 mm 48 mm 48 mm otor-ø 28 mm 30 mm 36 mm 41 mm Tip Speed in m/s 29.3 * 26.7 ** 32.0 ** 36.5 ** Applications small quantities coarse media suspending crushing, wet milling defibration, extracting small quantities finer media homogenizing emulsifying same as MTG 36/2 larger quantities finest homogenization and emulsification * measured at 20000 rpm ** measured at 17000 rpm All dispersing generators are easily interchangeable
MEGATON - Continuous Success New Designed Coupling The new coupling is an innovative design. The rotor is directly driven by the motor. The new star-coupling eliminates all the disadvantages of common belt drives and gear boxes: the mechanical strain forces to the bearings. Therefore, it minimizes wear and maintenance. Scale-Up The MEGATON MT 5000 is the smallest pilot plant unit available for in-line processing. KINEMATICA offers a complete series of continuously working in-line processors suitable for throughputs up to 130 000 l/h (575 gpm). The test results obtained with the pilot plant units allows a reliable scale-up to larger MEGATON industrial processors. MTO 5000 Q Working Chamber KINEMATICA - Your eliable Partner The founder of KINEMATICA, Professor Willems, patented the rotor/stator shear generator principle over forty years age. His ideas are incorporated in most of today s high-shear dispersers, colloid mills and shear pumps. Our POLYTON Laboratory Homogenizers are considered the market leader, worldwide. The same features which made the POLYTON the leading laboratory homogenizer are incorporated into our processing machines. They are: Quality, Innovation, Value, Integrity. We listen to your needs as a partner, in the mutual quest to find solutions to your processing requirements. MEGATON MT 1-200 Order Information (others on request) MT 5000 / 230V MT 5000 / 115V MTO 5000 MTK 5000 MTO 5000 Q MTK 5000 K MTG 36/2 MTG 36/4 MTG 48/2 MTG 48/6 ECO P 502 Basic unit, incl. motor drive, speed controller and digital display, 230V, 50 Hz Basic unit, incl. motor drive, speed controller and digital display, 115V, 50 Hz (with transformer) Working chamber, without cooling/heating jacket Working chamber, with cooling/heating jacket Working chamber, without cooling/heating jacket, with quench connections Working chamber, with cooling/heating jacket, with quench connections otor/stator Dispersing Generator otor/stator Dispersing Generator otor/stator Dispersing Generator otor/stator Dispersing Generator Electronic programming unit
Complete versatile Unbelievable Quiet The days of squeaky gear box transmissions and noisy brush motor drives have passed. A new generation of powerful and quiet 3-phase motors controls directly the entire speed range of the rotor. The result: only a soft rush of 62 db A can be heard. Lightweight and space Saving The MEGATON MT 5000 is a real lightweight: only 19 kg (42 lb). The compact design takes a space of only 30 x 40 cm (12x16 in.). The control module can be seperated from the motor drive and working chamber, thus making the MT 5000 system adaptable to any working environment. Standard Features All dispersing generators are easily interchangeable All parts in contact with the product are made from stainless steel (V4A, 1.4435, 316L), electropolished, except bearings and seals. Permanently lubricated, high temperature resistant, high speed ball bearings. NW 15 fittings in various designs available: straight tube, tube olives, NS coupling, TriClamp, etc. Motor drive: protection class IP 54, Isolation class F Options Other materials such as titanium, hastelloy, hardened alloys High pressure working chambers Sterile version Custom made design according to your requirements NW 15 fittings
Finest Solutions... worldwide! A wide range of products with the finest solution for every application, matched by the superior quality of all components make KINEMATICA a world leader for Dispersing and Mixing technology. With Keen Eyes... Development knows no rest at KINEMATICA. Our systems are constantly upgraded to reflect the state-of-the-art technology and the needs of the market. KINEMATICA has always had a keen eye for major advances, as proved by various patents. The rotor/stator principle for dispersing technology was conceived and developed at KINEMATICA and has become the world standard.... For Your Needs Applications for Dispersing/Homogenizing Technology are always on the increase. KINEMATICA continually creates new areas of processing applications based on innovations. We do not neglect the human factor as it is exemplified by the noise reduction of our high-speed systems. POLYTON BIOTONA MEGATON EACTON POLYMIX Dispersing Technology for Laboratory and Pilot Plant Batch- and Inline-Dispersing equipment Dispergier-und Mischtechnik Please, get in touch with us, our local appointed agent or your preferred dealer. We will be pleased to supply more details or arrange for a personal demonstration of our POLYTON and MEGATON systems. Feinste Lösungen... weltweit! Eine breite Produktpalette mit der optimalen Lösung für jede Applikation, sowie der hohe Qualitätsstandard aller Systemteile machen KINEMATICA zum weltweit führenden Unternehmen im Bereich der otor/stator-dispergier- und Mischtechnik. Mit offenen Ohren... KINEMATICA entwickelt die Systeme laufend weiter und bringt sie konzeptionell und konstruktiv auf den neuesten Stand der Technik. Denn KINEMATICA hat die Ohren noch nie vor dem verschlossen, was unerhörte Fortschritte bringt - davon zeugen auch verschiedene Patente. So hat sich das von KINEMATICA entwickelte otor/stator-dispergierprinzip weltweit durchgesetzt und bewährt. POLYTON BIOTONA MEGATON EACTON POLYMIX Homogenizing- and Dispersing Technology Inline- und Batch-Prozessors for Pilot Plant- and Production... für Ihre Bedürfnisse Die Einsatzbereiche der otor/stator-dispergiertechnik erweitern sich ständig. Das nicht zuletzt deshalb, weil KINEMATICA durch Innovationen, wie erhöhte Umfangs geschwindigkeiten, neue Arbeitsgebiete und neue Applikationen erschliesst - ohne dabei menschliche Aspekte zu vernachlässigen. Erinnert sei an das Bemühen um die Geräuschminderung am Arbeitsplatz. Wenden Sie sich an uns. Gerne senden wir Ihnen weitere Unterlagen oder führen Ihnen unsere POLYTON - und MEGATON -Systeme vor. epresented by / Vertreten durch: Dispersing- and Mixing Technology Dispergier-und Mischtechnik Luzernerstrasse 147a Tel. +41-41-259 65 65 CH-6014 Littau / Lucerne Fax +41-41-259 65 75 Switzerland e-mail laboratory@kinematica.ch web www.kinematica.ch eg-no. 12516-03 Printed in Switzerland (SIII) MT5000 12/2002, Subject to technical modifications