Phase-Adaptive Power Module

Similar documents
Phase-Adaptive Power Module with 3-Wire Fluorescent Input

Phase-Adaptive Power Module

Switching Power Module

3-Wire Fluorescent Power Module

LP Dimming Panels. GRAFIK Systems

DIN Power Module - Phase Adaptive

GRX-TVI Ten Volt Interface

GRX-TVI Ten Volt Interface

GRX-TVI Ten Volt Interface

GP Dimming Panels 230 Volt (CE)

Adaptive Power Module

Adaptive Power Module

GP Dimming Panels. GRAFIK Systems SPECIFICATION SUBMITTAL

EcoSystem Dimming Power Module for 3-wire Lutron Dimming Ballasts. EcoSystem One-Line. EcoSystem C5-BMJ-16A. EcoSystem Dimming Module

Maestro Wireless Dimmers and Switches

Wired Vareo Local Lighting Controls

DIN Rail Power Module

GP Dimming Panels 230 Volt (CE)

Wired Maestro Local Controls

Vive Maestro Wireless Dimmers and Switches

Ecosystem 5 Percent 3-Wire and Ecosystem Digital Link Controlled T4 Compact, 1 Lamp, Ballast Factor Of 0.95, K-Can, Studded, 26/32W

HomeWorks QS Designer RF Maestro Local Controls

Maestro Wireless Dimmers and Switches

RadioRA 2 Maestro Local Controls

HomeWorks QS Power Supply with Wire Harnesses

LCP128T Spec Grade Dimming System

Controls. CONTROLS AND ACCESSORIES PRODUCT FAMILY FEATURES DIMMERS DIMENSIONS SPECIFICATION SERIES STANDARD FEATURES

HomeWorksR QS Wired MaestroR Architectural Local Controls

Lumea C L Dimmer. Wallbox Controls

Installation Instructions Please Read Before Installing. Overview. Important Notes. Designer-Style Maestro Remotes HD-RD, -RS 120/127 V ~, 50/60 Hz

RadioRA 2 Maestro Local Controls

HomeWorks QS RF C L Hybrid seetouch Keypads

Residential Systems Control of LED Lighting (120V)

Maestro C.L multi-location dimmer 150W CFL/LED or 600W. Inc/Hal 120V In White Vive Enabled

Skylark Contour C L Dimmer

Skylark C L Dimmer. Skylark. C L Dimmer. Wallbox Controls

Maestro Wireless Dimmers

Hi-lume LED Overview. LED Dimming Driver Hi-lume LED Architectural Dimming

Skylark C L Dimmer. Skylark. C L Dimmer. Wallbox Controls

EcoSystem Multiple Control Input Ballasts

Skylark C L Dimmer. Skylark. Wallbox Controls. Dimmer for CFL and LED dimmable bulbs.

EcoSystemR Multiple Control Input Ballasts

Fluorescent (non-capacitive) Metal Halide 10A. 2 Any load circuit can be connected to any phase.

SAVE THESE INSTRUCTIONS

Ariadni 250 W C L Dimmer

Maestro Wireless Dimmers and Switches

INCANDESCENT/HALOGEN/MAGNETIC LOW VOLTAGE

SAVE THESE INSTRUCTIONS

Maestro Wireless Local Controls

Diva C L Dimmer. Wallbox Controls. Dimmer for CFL, LED, Halogen, and Incandescent dimmable bulbs.

Diva 250 W C L Dimmer

Touch the future of lighting control

Compact SE Overview. High-Performance Dimming. Ballast

Primary controls RadioRA 2 designer dimmers and switches

Hi-lume Premier 0.1% EcoSystemTM / 3-wire Constant Voltage 24 V- LED Driver with Soft-on, Fade-to-BlackTM

Skylark Contour C L Dimmer

L4B-F-RF Round Fixed Frame In BRO

RADIORA2 C.L Multi-Location Dimmer 150W CFL/Led or 600W Inc/Hal 120V In White. 6 to 277 VAC lights/3 VAC fan/3 VAC light and fan

Diva 250 W C L Dimmer

TOUCH THE FUTURE OF LIGHTING CONTROL

4000 Series Slider Control Units GRXSLD 4103/4104/4106/4108 CAUTION! Description. System Specifications. Installation Instructions Occupant Copy

Model Number Description Voltage Load Type Minimum Load Maximum Load. Incandescent / Halogen. General Purpose Fan

IVR15-SPI Solid State Illuminated Rail 2 Post Integral Power Supply

DRDHNJ Recessed LED Downlight General New Construction Junction Box

Installation Instructions

Hi-lume Overview. EcoSystem Hi-lume 1% Architectural Dimming

Installation & User Instructions

D4B-F-R 3 Series Round Frame In BRO

DRD2 Recessed LED Downlight General New Construction Junction Box PRODUCT SPECIFICATIONS

DRD2 Recessed LED Downlight General Remodel 4", 5", 6" Aperture

EcoSystemT 5-Series LED Driver ( V~, CE)

Customer service: or Upper mounting ring. Canopy

OneFrame & DRD2 Recessed LED Downlight General New Construction DRDHNJD Deep Junction Box

The RSQ LED Series provides continuous dimming with reverse or forward phase cut dimmers.

AYCL153PHWH 1P/3W CFL/Led Dimmer White

Application Note #637 Revision C November 2017 NEMA SSL 7A Dimmer Compliance List Including Compliance With CA Title 24

EcoSystem Multiple Control Input Ballasts

Mini Cavaletto. Recessed Adjustable Wall Wash

Taxonomies, Classifications, and Categories Residential dimmers, motion sensors, controls, & photo cells

Wiring Diagram Index. Find product, model #, and wiring diagram # Then find wiring diagrams on pgs

Industry Compliance The cabinet and modules are Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

DCC2. LED Cylinder JA8. Surface, Cord, Stem, Wall Mount

OneFrame & DRD2 Recessed LED Downlight General New Construction DRDHNJD Deep Junction Box

OneFrame & DRD2X Apex Series Recessed LED Downlight General New Construction DRDHNJD Deep Junction Box

Square-Style Faceplates

The HLB SeleCCTable LED Series provides continuous dimming with reverse or forward phase cut dimmers.

Tu-Wire Overview. Fluorescent Dimming Ballasts Tu-Wire 5% High-Performance Dimming

DRD2 Recessed LED Downlight Commercial New Construction 4", 6", 8" Aperture

MXS Matrix Small BRO

AYCL153PHWH 1P/3W CFL/Led Dimmer White. Ariadni CÂ L Dimmer, CFL/LED (Screw-based),

DRD2 Recessed LED Downlight General Retrofit Junction Box

Mini Cavaletto. Recessed Adjustable Wall Wash

ALD Dimmer Enclosures

DRD2 & SurfaceFrame. Shallow Recessed LED Downlight JA8. New Construction. DRDHNJO Octagonal Junction Box

Remote Power Supplies * & Dimmers (Sold Separately): Electronic Low Voltage Dimming (ELV) 0-10 Volt Dimming (0-10V) Lutron

Taxonomies, Classifications, and Categories Residential dimmers, motion sensors, controls, & photo cells

OneFrame & DRD4 Adjustable Recessed LED Downlight Concrete Tight New Construction DRDHNJC Deep Junction Box

OUTDOOR TRACK. LABELS Assembled in America

0.25" (0.64cm) Grip Jack Connector 2WDC WDC Lumen values are based on the 3000K LED test.

OneFrame & DRD2 Recessed LED Downlight Concrete Tight New Construction DRDHNJC Deep Junction Box

Transcription:

Phase-Adaptive Power Module Provides dimming control for 1 zone of a full 16 A lighting load. May be used to dim incandescent, halogen, electronic low-voltage, magnetic low-voltage, neon/cold cathode. Phase-adaptive technology automatically selects leading-edge or trailing-edge dimming for low-voltage transformers. Up to 3 power modules may be controlled by a single dimmer (C5-BMJ- will control only 1 module). Use PHPM-WBX- models for 3-wire fluorescent dimmer input and PHPM-PA- models for 2-wire input. PHPM-WBX- models can be used in conjunction with BCI-0-10 for 0 10 V dimming applications. For more information, see Application ote #516 (Lutron P/ 048516) at www.lutron.com Models available for control voltage of only or. Models available for load voltage of only or. Compatible with 220 / 240 V~, non-ce systems. Contact Lutron for specific system applications. ot for use with non-dim loads. Works with or versions of: Lutron in-wall dimmers; see approved list in the immers and Switches Specification Guide (Lutron P/ 3671746) at www.lutron.com (see Lighting Interfaces section) GRAFIK Eye QS control units * GRAFIK Eye 3000 Series control units ** LP, LCP, and GP dimming panels ** HomeWorks and HomeWorks QS remote power panels ** EcoSystem interface C5-BMJ-XXX * For PHPM PA models, set load type to power module. ** For PHPM-PA- models, set load type to incandescent. Use only PHPM-WBX models with this product; using PHPM-PA- models is not recommended 369835c 1 09.19.16 RadioRA 2 dimmers; see approved list in the specification submittal (Lutron P/ 369225) at www.lutron.com HomeWorks QS dimmers; see approved list in the specification submittal (Lutron P/ 369305) at www.lutron.com Models and Capacities Control Voltage 1, 2 Voltage 1, 2 Capacity Model umber 3, 4 16 A PHPM-PA-120-WH 16 A PHPM-PA-V-WH 16 A PHPM-PA-277 / V 16 A PHPM-WBX-120-WH 16 A PHPM-WBX-V-WH 16 A PHPM-WBX-277 / V 1 All voltages are phase-to-neutral. 2 For explanation of control voltage and load voltage, see page 5. 3 Use PHPM-PA- models for incandescent/halogen dimmers and set the controller load type to power module or incandescent. 4 Use PHPM-WBX- models for 3-wire fluorescent dimmers and set the controller load type to fluorescent. Lutron, )Lutron, GRAFIK Eye, HomeWorks, EcoSystem, RadioRA, and RTISS Equipped are trademarks of Lutron Electronics Co., Inc. registered in the U.S. and other countries. RadioRA 2 is a trademark of Lutron Electronics Co., Inc. Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

Specifications Power PHPM-PA-120-WH PHPM-PA-V-WH only PHPM-WBX-120-WH Control voltage PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V PHPM-PA-120-WH only PHPM-WBX-120-WH PHPM-PA-V-WH voltage PHPM-PA-277 / V PHPM-WBX-V-WH PHPM-WBX-277 / V Capacity: Full 16 A : 1920 W : 1920 4432 W Frequency: 50 / 60 Hz (output) power: Phase independent of control device/control voltage Sources/ Types Operates these sources with a smooth, continuous, Square Law dimming curve: Incandescent (tungsten) Halogen Magnetic low-voltage transformer (iron core) Electronic (solid-state) low-voltage transformer (must be manufacturer-approved for reverse-phase control dimming) eon / Cold cathode Incandescent and electronic low-voltage sources may be controlled on the same circuit / control zone. Up to 30% of the capacity of the unit can be used for incandescent lighting. Incandescent and magnetic low-voltage sources may be controlled on the same circuit/control zone. Up to 30% of the capacity of the unit can be used for incandescent lighting. Electronic low-voltage and magnetic low-voltage sources may OT be controlled on the same circuit / control zone. PHPM PA- and PHPM WBX- models are not for use with non dim loads. Use switching power module (PHPM SW V WH) for non dim loads. Minimum load on power module is 10 W. Output must be directly connected to the load. side switching is not recommended. 369835c 2 09.19.16 Key esign Features Automatically selects between forward-phase/ leading edge (e.g., magnetic low-voltage) and reversephase / trailing edge (e.g., electronic low-voltage) dimming / output based on connected load. Patented RTISS Equipped circuitry compensates in real time for incoming line voltage variations: Compensates for + / 2% change in RMS voltage/cycle and + / 2% Hz change in frequency/second. Provides air-gap off. Module protects itself during most temporary over-current and over-voltage conditions. Two LEs on front of unit provide diagnostic information (visible when faceplate is removed). Terminals Each terminal accepts up to two 12 AWG (2.5 mm 2 ) wires. Environment 32 to 104 F (0 to 40 C). Relative humidity less than 90% non-condensing. Indoor use only. Maximum heat output of module: 135 BTU / hour. Mounting Surface or recess mount. Power module is UL tested and approved for use in spaces designed for environmental air handling. Regulatory Approvals Models: PHPM PA 120 WH, PHPM PA V WH, PHPM WBX 120 WH, PHPM WBX V WH UL RoHS Compliant CSA OM CIET Complies with requirements for use in other spaces used for environmental air (plenums) per ECR 2014 300.22(C)(3). Models: PHPM PA 277 / V, PHPM WBX 277 / V UL RoHS Compliant Complies with requirements for use in other spaces used for environmental air (plenums) per ECR 2014 300.22(C)(3). Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

imensions and Mounting Mount in 2-gang U.S. wallbox, 3.5 in (89 mm) deep or 4 4 in (102 102 mm) junction box, 2.1 in (53 mm) deep. For indoor use only. This device generates heat; mount only where ambient temperature is 32 to 104 F (0 to 40 C). Mount with arrows facing up to ensure adequate cooling. Allow 4.5 in (114 mm) above and below faceplates when mounting several modules in a vertical layout. Units may butt together when mounted in a horizontal layout. Mount so line (mains) voltage wiring is at least 6 ft (1.8 m) from sound or electronic equipment and wiring. Mount within 7 of true vertical. Front View Mounting Methods Mount to 2-gang U.S. wallbox Mount to 4 4 in (102 102 mm), 2.1 in (53 mm) deep U.S. junction box 369835c 3 09.19.16 5.1 in (129.5 mm) 6.3 in (160 mm) Mount to 4 4 in (102 102 mm), 2.1 in (53 mm) deep U.S. junction box with barrier (for 277 V~ loads if required by local electrical code) Side View 1.2 in (30.5 mm) 1.4 in (35.5 mm) Barrier Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

Wiring 12 AWG (2.5 mm 2 ) copper (Cu) wires (75 C / 167 F minimum) for input power and load circuit. Strip 1/2 in (12 mm) insulation from wires before connecting. Run separate neutral for load circuit; no common neutrals. 369835c 4 09.19.16 May be used with GFI breaker protected loads. circuit wiring (from GFI breaker to power module to load) must be run in its own non-metallic conduit, or nuisance tripping may occur. Maximum 100 ft (30.5 m) between power module and load. May be used with AFI breaker protected loads. Maximum load on AFI circuit is 1000 W. Exceeding 1000 W may cause nuisance tripping of AFI breaker. Wiring to a immer Single Power Module to Single Control evice: Combined Power Feed for Control and Sides The power module may be on the same circuit / control zone as the control unit only if the total load does not exceed the rating of the breaker. Use PHPM-WBX- models for 3-wire fluorescent dimmers and PHPM-PA- models for other dimmer types. PHPM-PA-V-WH and PHPM-WBX-V-WH are included as only because of limits on zone-in voltages. For specific wire colors, see the wallbox lighting controls catalog (Lutron P/ 3691746) at www.lutron.com/wallbox Feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V Circuit breaker immer SH (capped) H (yellow / orange wire) H Control eutral Hot / Live eutral H immed Hot ot Used (continued on next page ) Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

Wiring to a immer (continued) Single Power Module to Single Control evice: Separate Power Feeds for Control and Sides The load breaker may be on a different phase from the control breaker. Use PHPM-WBX- models for 3-wire fluorescent dimmers and PHPM-PA- models for other dimmer types. feed must not exceed voltage rating of the load 1 ; control feed must not exceed voltage rating of the dimmer 2. For specific wire colors, see the wallbox lighting controls catalog (Lutron P/ 3691746) at www.lutron.com/wallbox 1 feed and load voltage refer to the circuit powering the load dimmed by the power module. 2 Control feed and control voltage refer to the circuit powering the dimmer that controls the power module. 369835c 5 09.19.16 Control breaker SH (capped) immer H (yellow / orange wire) Control feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V breaker feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V H Control eutral Hot / Live eutral H immed Hot ot Used (continued on next page ) Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

Wiring to a immer (continued) Multiple Power Modules to Single Control evice Shown with separate feeds for control and loads. All breakers must be turned off prior to installing or servicing the modules. Up to 3 power modules may be wired to a single dimmer. Use PHPM-WBX- models for 3-wire fluorescent dimmers and PHPM-PA- models for other dimmer types. feed must not exceed voltage rating of the load; control feed must not exceed voltage rating of the dimmer. For specific wire colors, see the wallbox lighting controls catalog (Lutron P/ 3691746) at www.lutron.com/wallbox SH (capped) H (yellow / orange wire) immer Control breaker 369835c 6 09.19.16 Control feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V breaker feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V H Control eutral breaker feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V H Control eutral Hot / Live eutral H immed Hot ot Used breaker feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V H Control eutral (continued on next page ) Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

Wiring to a immer (continued) 369835c 7 09.19.16 Single Power Module to Multiple Control evices The power module may be on the same circuit / control zone as the control unit only if the total load does not exceed the rating of the breaker. Use PHPM-WBX- models for 3-wire fluorescent dimmers and PHPM-PA- models for other dimmer types. feed must not exceed voltage rating of the load; control feed must not exceed voltage rating of the dimmer. For specific wire colors, see the wallbox lighting controls catalog (Lutron P/ 3691746) at www.lutron.com/wallbox Control feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V Control breaker Accessory / Companion immer or 3-Way Switch SH (capped) immer (Main immer) H (yellow / orange wire) breaker feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V H Control eutral Hot / Live eutral H immed Hot ot Used Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

Wiring to a GRAFIK Eye QS 369835c 8 09.19.16 Single Power Module to Single Control evice: Separate Power Feeds for Control and Sides The load type for the output must be set appropriately on the panel s circuit selector (for an LP or GP panel), on the controller (for an LCP panel), or in the HomeWorks software (for a HomeWorks panel). For PHPM-PA- models, set load type to incandescent. For PHPM-WBX- models, set load type to fluorescent. feed must not exceed voltage rating of the load; control feed must not exceed voltage rating of the dimmer. For specific wire colors, see the wallbox lighting controls catalog (Lutron P/ 3691746) at www.lutron.com/wallbox GRAFIK Eye QS Control Unit 123456L Wire to appropriate zone Control breaker Control feed PHPM-PA-V-WH 220 240 V~ PHPM-PA-277 / V breaker feed PHPM-PA-V-WH PHPM-PA-277 / V H Control eutral Hot / Live eutral H immed Hot ot Used Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

Wiring to an EcoSystem C5-BMJ Interface (for PHPM-WBX- models only) 369835c 9 09.19.16 Single Power Module to Single imming Module: Separate Power Feeds for Control and Sides The load breaker may be on a different phase from the control breaker. Use PHPM-WBX- models only. feed must not exceed voltage rating of the load. For specific wire colors, see the wallbox lighting controls catalog (Lutron P/ 3691746) at www.lutron.com/wallbox Control feed PHPM-WBX-V-WH PHPM-WBX-277 / V Control breaker H (Orange) (White) SH (Red) (capped) C5-BMJ-16A breaker feed PHPM-WBX-V-WH PHPM-WBX-277 / V H Control eutral PHPM-WBX- models only Hot / Live eutral H immed Hot ot Used Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber:

Wiring to an LP, GP, LCP, or HomeWorks Panel 369835c 10 09.19.16 Single or Multiple Power Modules to Single Power Panel The load type for the output must be set appropriately on the panel s circuit selector (for an LP or GP panel), on the controller (for an LCP panel), or in the HomeWorks software (for a HomeWorks panel). For PHPM-PA- models, set load type to incandescent. For PHPM-WBX- models, set load type to fluorescent. feed must not exceed voltage rating of the load. For specific wire colors, see the wallbox lighting controls catalog (Lutron P/ 3691746) at www.lutron.com/wallbox (1) 14 to 10 AWG (2.0 to 4.0 mm 2 ) immed Hot (1) 14 to 10 AWG (2.0 to 4.0 mm 2 ) eutral H H H H H breaker feed PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V H Control eutral Hot / Live eutral H immed Hot ot Used Control Voltage: PHPM-PA-V-WH PHPM-WBX-V-WH PHPM-PA-277 / V PHPM-WBX-277 / V Branch circuit breakers Power (Hot / Live) (3) 14 to 2/0 AWG (2.0 to 70 mm 2 ) eutral (1) 14 to 2/0 AWG (2.0 to 70 mm 2 ) Job ame: SPECIFICATIO SUBMITTAL Model umbers: Job umber: