Description CMP servomotors are delivered with 2-pole resolvers as standard. Further information on other resolvers is available on request.

Motor types Standard type encoders 11 11 Motor types 11.1 Standard type encoders 11.1.1 Resolver Type designation /RH1M Description CMP servomotors are delivered with 2-pole resolvers as standard. Further information on other resolvers is available on request. 11.1.2 Option: Hiperface encoders 11 CMP servomotors are optionally available with the following Hiperface multi-/singleturn encoders: Designation Specification periods / revolution Motor type Brake types EK0H 128 CMP40 BK AK0H 1) 128 CMP40 63, CMP.71 100, CMP112 BP/BK ES1H, AS1H 1024 CMP50 63 EK1H, AK1H 1) 1024 CMP50 63/BK, CMP.71 100, CMP112 BP/BK/BY 1) Also available as safety-rated version Type designation /AK0H, /EK0H, /AK1H, /EK1H Description SEW EURODRIVE offers Hiperface encoders also as multi-turn absolute encoders as an alternative to the resolver. Encoders with a high resolution are also available in addition to the standard. INFORMATION The encoder signal can be influenced when applying the brake from speed. It is therefore important that the inverter defines its encoder position again after this process. This is not necessary in regular operation when the brake is actuated at standstill. When prefabricating the encoder cables, ensure correct polarity for the supply outputs. Catalog CMP40 CMP112, CMPZ71 CMPZ100 305

11 Motor types Standard type encoders 11.1.3 Encoders technical data Resolver /RH1M Type RH1M CMP40 63, CMP.71 100, CMP112 Number of poles 2 Primary Rotor Input voltage 7 V Input frequency 7 khz Reduction ratio ± 10% 0.5 Phase shift ± 5 +13 Input impedance ± 15% 130 + j120 Ω Output impedance ± 15% 200 + j270 Ω Input resistance ± 10% 82 Ω Output resistance ± 10% 68 Ω Maximum electrical fault ± 6 Temperature range -55 C to +150 C 306 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type encoders 11 Option: Hiperface encoder /EK0H, /AK0H Type EK0H AK0H 1) Attachable to encoder CMP40 CMP40 63, CMP.71 100, CMP112 Supply voltage Maximum current consumption (without load) Maximum operating frequency DC 7 to 12 V polarity reversal protected 120 ma 26 khz Pulses (sine cycles) per revolution 128 Output amplitude per track Single-turn resolution 0.8 to 1.1V pp sin/cos 4096 increments/revolution (15 bits) Multi-turn resolution 4096 revolutions (12 bits) 11 Transmission protocol Hiperface Serial data output Driver to EIA RS-485 Vibration resistance (10 to 2000 Hz) 100 m/s 2 (DIN IEC 68 2 6) Maximum speed 12000 rpm 9000 rpm Temperature range -20 C to +110 C 1) Not available in combination with BY brake Catalog CMP40 CMP112, CMPZ71 CMPZ100 307

11 Motor types Standard type encoders Option: Hiperface encoders /ES1H, /AS1H Type ES1H AS1H Attachable to encoder Supply voltage Max. current consumption Maximum operating frequency CMP50, CMP63 DC 7 8 12 V polarity reversal protected 140 ma 200 khz Pulses (sine cycles) per revolution 1024 Output amplitude per track Single-turn resolution 0.9 to 1.1 V pp sin/cos 32768 increments/revolution (15 bits) Multi-turn resolution 4096 revolutions (12 bits) Transmission protocol Hiperface Serial data output Driver to EIA RS-485 Vibration resistance (10 to 2000 Hz) 200 m/s 2 (DIN IEC 68 2 6) Maximum speed 12000 rpm Temperature range -20 C to +110 C /EK1H, /AK1H Type EK1H AK1H Attachable to encoder Supply voltage Max. current consumption Maximum operating frequency CMP50 63/BK, CMP.71 100, CMP112 DC 7 8 12 V polarity reversal protected 140 ma 200 khz Pulses (sine cycles) per revolution 1024 Output amplitude per track Single-turn resolution 0.9 to 1.1 V pp sin/cos 32768 increments/revolution (15 bits) Multi-turn resolution 4096 revolutions (12 bits) Transmission protocol Hiperface Serial data output Driver to EIA RS-485 Vibration resistance (10 to 2000 Hz) 200 m/s 2 (DIN IEC 68 2 6) Maximum speed 12000 rpm Temperature range -30 C to +110 C 308 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type encoders 11.1.4 11 Safety-rated encoders General information Hiperface encoders AK0H and AK1H are optionally available for functional safety. Using safety-rated encoders lets you implement safety functions SS1, SS2, SOS, SLA, SLS, SDI, and SLI according to IEC 61800 5 2. Certain demands on the mechanical coupling of the encoder system to the motor must be met so that the encoder can be used for safety-relevant tasks. SEW EURODRIVE assumes responsibility for the delivered motor with safety-rated encoder in terms of compliance with the functional safety regulations. Safety-relevant connection elements are sealed to be able to ensure that the delivery condition is not changed, see following figures. CMP40 CMP50 63 11 AK0H [1] [1] 9007203017040651 CMP71 100 9007203017042315 CMPZ71 100, CMP71 100 /BP, CMP112 [1] [1] 9007203017045643 9007203017043979 Catalog CMP40 CMP112, CMPZ71 CMPZ100 309

11 Motor types Standard type encoders AK1H CMP71 100 CMPZ71 100, CMP71 100 /BP, CMP112 CMPZ71 100 /BY, CMP112 /BY [1] 9007203034362379 [1] 3779561099 [1] Sealed screw connections on the encoder [1] 8468802571 310 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type encoders 11 Characteristic safety values Characteristic safety values for AK0H encoders The following table shows the characteristic safety values of the safety-rated AK0H encoders: Characteristic values according to EN 62061 / IEC 61508 EN ISO 13849 1 Classification/underlying standards SIL2 according to EN 62061 PL d according to EN ISO 13849-1 Structure HFT = 1 2 channels (corresponds to category 3 according to EN ISO 13849-1) Probability of a dangerous failure per hour (PFH d value) 1.3 10-8 1/h 1) 11 Mean time to dangerous failure 100 years (MTTF d value) 2) Mission time / service life 20 years Proof test interval Not required Safe fault coverage (SSF) 95% Motor/encoder connection In the drive with FS identification, exclusion of errors according to EN ISO 13849 1) The specified value refers to the diagnostics coverage of 90% that must be achieved by an encoder evaluation unit. Diagnostics must be performed within the process response time. 2) Ambient temperature 40 C Catalog CMP40 CMP112, CMPZ71 CMPZ100 311

11 Motor types Standard type encoders Characteristic safety values for AK1H encoders The following table shows the characteristic safety values of the safety-rated AK1H encoder: Characteristic values according to EN 62061 / IEC 61508 EN ISO 13849 1 Classification/underlying standards SIL2 according to EN 62061 PL d according to EN ISO 13849-1 Structure HFT = 1 2 channels (corresponds to category 3 according to EN ISO 13849-1) Probability of a dangerous failure per hour (PFH d value) 1.0 10-8 1/h 1) Mean time to dangerous failure 1073 years (MTTF d value) 2) Mission time / service life 20 years Proof test interval Not required Safe fault coverage (SSF) 95% Motor/encoder connection In the drive with FS identification, exclusion of errors according to EN ISO 13849 1) The specified value refers to the diagnostics coverage of 90% that must be achieved by an encoder evaluation unit. Diagnostics must be performed within the process response time. 2) Ambient temperature 40 C 312 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type motor protection 11 11.2 Standard type motor protection 11.2.1 Thermal motor information with KTY Type designation /KY Description This type detects the motor temperature continuously using a semi-conductor sensor for further processing in the inverter or controller. The inverter + /KY option can only take on the function of motor protection when it is used in combination with an inverter containing the thermal motor model. 11.2.2 Thermal motor information with KTY technical data 11 /KY KTY84 to 130 temperature sensors continuously detect the motor temperature. Technical data KTY84 to 130 Connection Red (+) Blue ( ) Total resistance at 20 to 25 C Test current 540 Ω < R < 640 Ω < 3 ma Typical characteristic curve of KTY: 3000 2500 2000 R Ω 1500 1000 500 0-100 -50 0 50 100 150 200 250 300 350 T C 4816000395 Catalog CMP40 CMP112, CMPZ71 CMPZ100 313

11 Motor types Standard type motor protection 11.2.3 TF temperature sensor Type designation /TF Description Thermal motor protection prevents the motor from overheating and causing irreparable damage. The TF is a triple PTC thermistor. One TF is installed in every motor phase and then connected in series. A PTC thermistor is a resistance whose resistance value rises significantly from a nominal response value as the temperature rises. Please refer to the following characteristic curve. The temperature sensor /TF can be designed as follows: in thermal class 155 (F) in thermal class 180 (H) in a double version for warning in 130 (B) and for disconnection in 155 (H), for warning in 155 (F) and for disconnection in 180 (H). Please contact us if you are considering the double /TF design. Notes on the selection The positive temperature coefficient (PTC) temperature sensors comply with DIN 44082. Resistance measurement (measuring instrument with V 2.5 V or < 1 ma): Standard measured values: 20 500 Ω Hot resistance: > 4000 Ω When using the temperature sensor for thermal monitoring, the evaluation function must be activated to maintain reliable isolation of the temperature sensor circuit. If the temperature reaches an excessive level, the thermal protection function must be brought into effect immediately. INFORMATION The temperature sensor /TF may not be subjected to voltages > 30 V. 314 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type motor protection 11 The below figure shows the characteristic curve of a TF with reference to the nominal response temperature (referred to as T NF ). R [Ω] 4000 1330 550 250 11 [T] -20 C T NF - 20 K T NF - 5 K T NF + 5 K T NF + 15 K T NF 4151365003 Catalog CMP40 CMP112, CMPZ71 CMPZ100 315

11 Motor types Standard type connection options 11.3 Standard type connection options 11.3.1 Assignment table for connectors and terminal boxes to CMP servomotors Key: Version possible Version not possible System voltage 400 V, without forced cooling fan Motor type Rated speed Power connection without/with brake SM1/SB1 SMB/SBB SMC/SBC KK KKS IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA CMP40S 3000 4500 6000 CMP40M 3000 4500 6000 CMP50S 3000 4500 6000 CMP50M 3000 4500 6000 CMP50L 3000 4500 6000 CMP63S 3000 4500 6000 CMP63M 3000 4500 6000 CMP63L 3000 4500 6000 CMP.71S 2000 3000 4500 6000 CMP.71M 2000 3000 4500 6000 CMP.71L 2000 3000 4500 6000 CMP.80S 2000 3000 4500 6000 316 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 Motor type Rated speed Power connection without/with brake SM1/SB1 SMB/SBB SMC/SBC KK KKS IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA CMP.80M 2000 3000 4500 6000 CMP.80L 2000 3000 4500 6000 CMP.100S 2000 3000 4500 CMP.100M 2000 3000 4500 CMP.100L 2000 3000 4500 CMP112S 2000 3000 4500 CMP112M 2000 3000 4500 CMP112L 2000 3000 4500 CMP112H 2000 3000 4500 CMP112E 2000 3000 4500 11 Catalog CMP40 CMP112, CMPZ71 CMPZ100 317

11 Motor types Standard type connection options System voltage 400 V, with forced cooling fan Motor type Rated speed Power connection without/with brake SM1/SB1 SMB/SBB SMC/SBC KK KKS IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA CMP50S/ VR 3000 4500 6000 CMP50M/ VR 3000 4500 6000 CMP50L/ VR 3000 4500 6000 CMP63S/ VR 3000 4500 6000 CMP63M/ VR 3000 4500 6000 CMP63L/ VR 3000 4500 6000 CMP.71S/ VR 2000 3000 4500 6000 CMP.71M/ VR 2000 3000 4500 6000 CMP.71L/ VR 2000 3000 4500 6000 CMP.80S/ VR 2000 3000 4500 6000 CMP.80M/ VR 2000 3000 4500 6000 CMP.80L/ VR 2000 3000 4500 CMP.100S/ VR 2000 3000 4500 CMP.100M/ VR 2000 3000 4500 CMP.100L/ VR 2000 3000 4500 318 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 Motor type Rated speed Power connection without/with brake SM1/SB1 SMB/SBB SMC/SBC KK KKS IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA CMP112S/ VR 2000 3000 4500 CMP112M/ VR 2000 3000 4500 CMP112L/ VR 2000 3000 4500 CMP112H/ VR 2000 3000 4500 CMP112E/ VR 2000 3000 4500 11 Catalog CMP40 CMP112, CMPZ71 CMPZ100 319

11 Motor types Standard type connection options System voltage 230 V, without forced cooling fan Motor type Rated speed CMP40S 3000 4500 6000 CMP40M 3000 4500 6000 CMP50S 3000 4500 6000 CMP50M 3000 4500 6000 CMP50L 3000 4500 6000 CMP63S 3000 4500 6000 CMP63M 3000 4500 6000 CMP63L 3000 4500 6000 CMP.71S 3000 4500 6000 CMP.71M 3000 4500 CMP.71L 3000 CMP.80S 3000 4500 6000 CMP.80M 3000 4500 CMP.80L 3000 CMP.100S 3000 4500 CMP.100M 3000 Power connection without/with brake SM1/SB1 SMB/SBB SMC/SBC KK KKS IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA 320 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 System voltage 230 V, with forced cooling fan Motor type Rated speed CMP.71S/ VR 3000 4500 6000 CMP.71M/ VR 3000 4500 CMP.71L/ VR 3000 CMP.80S/ VR 3000 4500 6000 CMP.80M/ VR 3000 4500 CMP.80L/ VR 3000 Power connection without/with brake SM1/SB1 SMB/SBB SMC/SBC KK KKS IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA IEC UL CSA 11 Catalog CMP40 CMP112, CMPZ71 CMPZ100 321

11 Motor types Standard type connection options 11.3.2 Plug connector connection option CMP40 CMP63: SM1/SB1 plug connector Adjustable Radial CMP.71 CMP.100, CMP112: SM1/SB1 plug connector Adjustable Radial 9288496267 CMP.71 CMP.100, CMP112: SMB/SBB plug connector Adjustable Radial 9288498187 322 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 CMP100, CMP112: Plug connectors SMC/SBC X 1 3 11 18014405627737355 The power connector size S.C is not available as adjustable type. It can be ordered in 3 positions (positions X, 1, 3). If not specified otherwise in the order, the power connector is supplied in position 3 (standard position). The signal connector is adjustable. Catalog CMP40 CMP112, CMPZ71 CMPZ100 323

11 Motor types Standard type connection options 11.3.3 Power cables and plug connectors for CMP motors Cable type Connector type Thread size Cable cross section Prefabricated cables Part number Replacement mating connector * Fixed installation Motor cable SM11 M23 4 x 1.5 mm 2 05904544 01986740 Cable carrier installation Brakemotor cable 1) BP brake Brakemotor cable BY brake SM12 4 x 2.5 mm 2 05904552 01986740 SM14 4 x 4 mm 2 05904560 01991639 SMB6 M40 4 x 6 mm 2 13350269 13349856 SMB10 4 x 10 mm 2 13350277 13349864 SMB16 4 x 16 mm 2 13350285 13349872 SMC16 M58 4 x 16 mm 2 18148476 18150349 SB11 M23 4 x 1.5 mm 2 + 2 x 1 mm 2 13354345 01986740 SB12 4 x 2.5 mm 2 + 2 x 1 mm 2 13354353 01986740 SB14 4 x 4 mm 2 + 2 x 1 mm 2 13354361 01991639 SBB6 M40 4 x 6 mm 2 + 2 x 1.5 mm 2 13350196 13349856 SBB10 4 x 10 mm 2 + 2 x 1.5 mm 2 13350218 13349864 SBB16 4 x 16 mm 2 + 2 x 1.5 mm 2 13350226 13349872 SBC16 M58 4 x 16 mm 2 + 3 x 1.5 mm 2 18148514 18150349 Motor cable SM11 M23 4 x 1.5 mm 2 05906245 01986740 Brakemotor cable 2) BP brake Brakemotor cable BY brake 1) BP brake:3-core cable, only 2 cores are used 2) BP brake:3-core cable, only 2 cores are used SM12 4 x 2.5 mm 2 05906253 01989197 SM14 4 x 4 mm 2 05904803 01991639 SMB6 M40 4 x 6 mm 2 13350293 13349856 SMB10 4 x 10 mm 2 13350307 13349864 SMB16 4 x 16 mm 2 13350315 13349872 SMC16 M58 4 x 16 mm 2 18148484 18150349 SMC25 4 x 25 mm 2 18148581 18150160 SMC35 4 x 35 mm 2 18148697 18150179 SB11 M23 4 x 1.5 mm 2 + 2 x 1 mm 2 13354388 01989197 SB12 4 x 2.5 mm 2 + 2 x 1 mm 2 13354396 01989197 SB14 4 x 4 mm 2 + 2 x 1 mm 2 13421603 01991639 SBB6 M40 4 x 6 mm 2 + 2 x 1.5 mm 2 13350234 13349856 SBB10 4 x 10 mm 2 + 2 x 1.5 mm 2 13350242 13349864 SBB16 4 x 16 mm 2 + 2 x 1.5 mm 2 13350250 13349872 SBC16 M58 4 x 16 mm 2 + 3 x 1.5 mm 2 18148522 18150349 * The complete connector service pack always includes the following parts: Power connector Insulation inserts Socket contacts 324 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 11.3.4 Power cables and plug connectors for CMPZ motors Cable type Connector type Thread size Cable cross section mm 2 Prefabricated cables Part number Replacement mating connector * Fixed installation Motor cable SM11 M23 4 x 1.5 mm 2 05904544 01986740 Cable carrier installation Brakemotor cable BY brake SM12 4 x 2.5 mm 2 05904552 01986740 SM14 4 x 4 mm 2 05904560 01991639 SMB6 M40 4 x 6 mm 2 13350269 13349856 SMB10 4 x 10 mm 2 13350277 13349864 SMB16 4 x 16 mm 2 13350285 13349872 SB11 M23 4 x 1.5 mm 2 + 3 x 1 mm 2 13354272 01986740 SB12 4 x 2.5 mm 2 + 3 x 1 mm 2 13354280 01986740 SB14 4 x 4 mm 2 + 3 x 1 mm 2 13354299 01991639 SBB6 M40 4 x 6 mm 2 + 3 x 1.5 mm 2 13350129 13349856 SBB10 4 x 10 mm 2 + 3 x 1.5 mm 2 13350137 13349864 SBB16 4 x 16 mm 2 + 3 x 1.5 mm 2 13350145 13349872 Motor cable SM11 M23 4 x 1.5 mm 2 05906245 01986740 Brakemotor cable BY brake SM12 4 x 2.5 mm 2 05906253 01989197 SM14 4 x 4 mm 2 05904803 01991639 SMB6 M40 4 x 6 mm 2 13350293 13349856 SMB10 4 x 10 mm 2 13350307 13349864 SMB16 4 x 16 mm 2 13350315 13349872 SB11 M23 4 x 1.5 mm 2 + 3 x 1 mm 2 13354302 01989197 SB12 4 x 2.5 mm 2 + 3 x 1 mm 2 13354310 01989197 SB14 4 x 4 mm 2 + 3 x 1 mm 2 13354329 01991639 SBB6 M40 4 x 6 mm 2 + 3 x 1.5 mm 2 13350153 13349856 SBB10 4 x 10 mm 2 + 3 x 1.5 mm 2 13350161 13349864 SBB16 4 x 16 mm 2 + 3 x 1.5 mm 2 13350188 13349872 * The complete connector service pack always includes the following parts: Power connector Insulation inserts Socket contacts 11 Catalog CMP40 CMP112, CMPZ71 CMPZ100 325

11 Motor types Standard type connection options 11.3.5 Plug connector connection option technical data Illustration of the mating connectors: [1] [2] [3] [1] Radial mating connector [2] Angled mating connector [3] Mating connector for forced cooling fan 4816072075 Key [A] [C] [B] [A] [D] [B] [A] [B] [C] [D] View A View B Customer connector with socket contacts Flange socket with pin contacts installed at the factory 8790995467 NOTICE Damage to the BK brake. Possible damage to property. It is essential that you observe the correct polarity of BK brake supply. Check the polarity when replacing the brake. 326 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 SM1/SB1 power connector (M23) Wiring diagram with/without BP/BK brake -/ +/ [1] [A] [B] BK(3) BK D 3 BK(1) C GNYE W W1 BU 3 D GNYE C BK=BU- BP=YE [1] B 4 A 1 BK BK V U V1 U1 RD BK 1 4 A B BK=RD+ BP=YE 8790987787 [1] BP/BK brake (optional) Connection of power plug connector SM1 / SB1 (M23) 11 Wiring diagram with/without BY brake 15 13 14 [2] [1] [A] [B] BK BU W W1 BK(3) BK(1) BK(2) C B D 4 A 3 1 GNYE BK V BK U V1 U1 GNYE RD BK 3 1 D 4 A C B BU RD WH [1] 8790989707 [1] BY brake (optional) [2] Connection to SEW rectifier according to operating instructions Connection of SMB/SBB power plug connector (M40) Wiring diagram with/without BP brake [1] [A] [B] 13 BK(1) YE BK(3) 15 [2] - W 2 V + 1 U BK V BK U V1 U1 RD BK V + U - W 1 2 YE [1] GNYE GNYE [1] BP brake (optional) [2] Connection to SEW rectifier according to operating instructions BK W W1 BU 8791076107 Catalog CMP40 CMP112, CMPZ71 CMPZ100 327

11 Motor types Standard type connection options Connection of SMB/SBB power plug connector (M40) Wiring diagram with/without BY brake [1] [A] [B] RD [2] 13 BK(1) BU 15 BK(3) 14 BK(2) - W 2 V + U 1 BK V BK GNYE U V1 U1 RD BK GNYE + U 1 V 2 - W WH [1] BK W W1 BU 8791078027 [1] BY brake (optional) [2] Connection to SEW rectifier according to operating instructions. For BY.D, connection 14 is omitted. Connection of SMC/SBC power plug connector (M58) Wiring diagram with/without BY brake [1] [A] [B] RD BU 13 BK(1) BK(3) 15 14 BK(2) [2] - W 1 V + U 2 BK V BK GNYE U V1 U1 RD BK GNYE + U 2 V 1 - W WH [1] BK W W1 BU 8791074187 [1] BY brake (optional) [2] Brake coil 328 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 Wiring diagram for RH1M resolver signal plug connectors Wiring diagram [A] [1] [2] [B] PK GY 2 1 9 8 7 BNVT KTY+ (TF) RD (BK) 8 7 9 1 2 RDWH BKWH R1 (Referenz +) R2 (Referenz -) WHBK 3 10 12 6 6 12 10 3 BU (BK) KTY- (TF) [2] RD 4 11 5 GN S4 (Sinus -) BU 5 11 4 RD S1 (Cosinus +) BU YE S2 (Sinus +) YE BK S3 (Cosinus -) 8790991627 [1] Shield connected to the metal housing of the connector. Colors according to SEW-EURODRIVE cables [2] KTY+ (RD), KTY-(BU), optional TF (BK) 11 Pin assignment of plug connector lower part Pin Color code Connection 1 RD/WH R1 (reference +) 2 BK/WH R2 (reference -) 3 RD S1 (cosine +) 4 BK S3 (cosine ) 5 YE S2 (sine +) 6 BU S4 (sine ) 7 8 9 RD KTY + 10 BU KTY 11 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 329

11 Motor types Standard type connection options Connection of signal plug connectors, AK0H, EK0H, AK1H, EK1H encoders Wiring diagram WH RD BU GYPK; PK 2 1 9 [A] 8 7 3 10 12 6 11 4 5 [1] [2] BN BK VT RDBU; GY GN YE KTY+ (TF) D + D - Us S4 (Sinus -) S2 (Sinus +) RD (BK) BK VT GY GN YE 7 6 5 8 12 [B] 9 10 1 11 4 2 3 BU (BK) RD BU PK KTY- (TF) [2] S1 (Cosinus +) S3 (Cosinus -) GND 8790993547 [1] Shield connected to the metal housing of the connector. Colors according to SEW EURODRIVE cables [2] KTY+ (RD), KTY-(BU), optional TF (BK) Pin assignment of plug connector lower part Pin Color code Connection 1 2 3 RD S1 (cosine +) 4 BU S3 (cosine ) 5 YE S2 (sine +) 6 GN S4 (sine ) 7 VT D 8 BK D + 9 RD KTY + 10 BU KTY 11 PK Voltage reference (GND) 12 GY Supply voltage Vs 330 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 11.3.6 KK and KKS terminal box connection option 11 2900866059 Connection cross section Motor type Power connection Encoder / resolver / thermal motor protection CMP50, CMP63 Connection Spring terminals Maximum connection cross section Cable entry Connection Cable entry 6 mm 2 M25 Spring terminals M20 CMP71, CMP80 M6 stud 10 mm 2 M32 M16 CMP100 M8 stud 25 mm 2 M40 CMP112S/M/L M8 stud 35 mm 2 M50 CMP112H/E M10 stud 50 mm 2 M50 Catalog CMP40 CMP112, CMPZ71 CMPZ100 331

11 Motor types Standard type connection options 11.3.7 Connection of CMP50 and CMP63 PE W V U 4a 5a10 9 8 7 6 5 4 3 2 1 2900869771 Power Pin Core identification Connection U V W (BK/WH) Black with white lettering U, V, W PE (GN/YE) Green/yellow PE conductor U V W BP brake, BK brake Auxiliary terminal contacts Core identification BP BK BMV brake rectifier connection BS brake controller connection 4 a + + 13 3 (RD) (YE) Yellow (RD) Red 5a 15 5 (BU) (YE) Yellow (BU) Blue The brake has a standard supply voltage of DC 24 V. NOTICE Damage to the BK brake. Possible damage to property. It is essential that you observe the correct polarity of BK brake supply. Check the polarity when replacing the brake. 332 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 Signal Resolver Encoder 1 ref + Reference 1 cos + Cosine 2 ref - 2 ref cos Reference 3 cos + Cosine 3 sin + Sine 4 cos - 4 ref sin Reference 5 sin + Sine 5 D - DATA 6 sin - 6 D + DATA 7-7 GND Ground 8-8 Us Supply voltage 9 KTY + / (TF) Motor protection 9 KTY + / (TF) Motor protection 10 KTY - / (TF) 10 KTY - / (TF) 11 Catalog CMP40 CMP112, CMPZ71 CMPZ100 333

11 Motor types Standard type connection options 11.3.8 CMP71 CMP112 connection U V W 3a 4a 5a 1 2 3 4 5 6 7 8 9 10 U V W 3a 4a 5a [1] [1] KK terminal box [2] KKS terminal box [2] 9007202155616523 Power rating Pin Core identification Connection U V W (BK/WH) Black with white lettering U, V, W PE (GN/YE) Green/yellow PE conductor U V W BP brake Auxiliary terminal contacts Core identification 4 a (BK/WH) BMV brake rectifier connection BS brake controller connection 5a Black with white 15 5 lettering 1, 2, 3 The brake has a standard supply voltage of DC 24 V. 13 3 334 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Standard type connection options 11 BY brake Auxiliary terminal contacts Core identification 3 a (BK/WH) Connection of BME, BMP, BMH, BMK brake rectifiers Connecting the BSG brake control unit 14 1 4 a Black with white 13 3 5a lettering 1, 2, 3 15 5 Signal Resolver Encoder 1 ref + Reference 1 cos + Cosine 2 ref 2 ref cos Reference 3 cos + Cosine 3 sin + Sine 4 cos 4 ref sin Reference 5 sin + Sine 5 D DATA 6 sin 6 D + DATA 7 7 GND Ground 8 8 Us Supply voltage 9 KTY + / (TF) Motor protection 9 KTY + / (TF) Motor protection 10 KTY / (TF) 10 KTY / (TF) 11 11.3.9 Connection option via terminal box The following figure shows the power connection in the terminal box. [1] [6] [2] [3] [7] [4] [5] [8] 9007202155623307 [1] Terminal studs [5] Terminal board [2] Upper nut [6] Customer's cable [3] Washer [7] Bottom nut [4] Motor cable [8] Lock washer For designing the terminal box, positions 4, 6 and 7 are regarded as current-carrying. Catalog CMP40 CMP112, CMPZ71 CMPZ100 335

11 Motor types Additional feature forced-cooling fan 11.4 Additional feature forced-cooling fan Type designation: /VR 11.4.1 Description Synchronous servomotors can be equipped with a forced cooling fan if requested. The VR forced cooling fan is available for DC 24 V (CMP50 to CMP112, CMPZ71 to CMPZ100). A forced cooling fan can be retrofitted to these motors later using a retrofit set. For CMPZ71 to CMPZ100 motors, the forced cooling fan /VR option can no longer be combined with the manual brake release /HR option. INFORMATION The forced cooling fan can only be used up to a maximum oscillation and shock load of 1 g. INFORMATION Before retrofitting a forced cooling fan, it is important to check whether the previously used motor plug connectors/cables are permitted for the increased current consumption. 11.4.2 Mechanical installation Mounting the fan guard for the VR forced cooling fan: Motor Bolts Tightening torque CMP50, CMP63 M4 8 self-tapping 4 Nm CMP.71 M6 20 4 Nm 1) CMP.80, CMP.100 M8 20 10 Nm 1) CMP112 M10 x 25 15 Nm 1) 1) Additional Loctite thread locking compound 2903413131 336 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Additional feature forced-cooling fan 11 11.4.3 Electrical connection The VR forced cooling fan is only available for DC 24 V voltage. DC 24 V ± 20% Plug connector connection Maximum connection cross section 2 x 1 mm 2 Pg7 cable gland with 7 mm inside diameter DC 24 V - + 2 1 Connector contact Connection 1 24 V + 2 0 V 11 11.4.4 Retrofit set for CMP50 / CMP63 INFORMATION The forced cooling fan retrofit set for motors CMP50 to CMP63 may only be mounted by staff authorized by SEW EURODRIVE. 11.4.5 Forced cooling fan technical data Forced cooling fan type VR Motor size CMP50 CMP63 CMP.71 CMP.80 CMP.100 CMP112 Supply voltage DC 24 V ± 20% Current consumption DC 0.15 A 0.25 A 0.88 A 0.88 A 1.67 A 1.67 A Power consumption 3.5 W 6 W 21 W 21 W 40 W 40 W Air discharge rate 56 m 3 /h 80 m 3 /h 275 m 3 /h 275 m 3 /h 540 m 3 /h 540 m 3 /h Ambient temperature -20 C to 60 C Degree of protection IP54 / IP55 Electrical connection Plug connector Max. cable cross section 3 1 mm 2 Inner diameter of the cable gland 7 mm Catalog CMP40 CMP112, CMPZ71 CMPZ100 337

11 Motor types Additional feature forced-cooling fan UWU52A switched-mode power supply The AC voltage type includes a VR forced cooling fan and the UWU52A switchedmode power supply. Input: AC 110 to 240 V; 1.04 to 0.63 A; 50/60 Hz Output: DC 24 V; 2.5 A (40 C); 2.0 A (55 C) Connection screw terminals 0.2 to 2.5 mm 2, separable. Degree of protection: IP20; attachment to EN 60715 TH35 support rail in the control cabinet. Part number: 0188 1817. Dimensions of the UWU52A switched-mode power supply: 76 101 111 38 4816285067 Part numbers of forced cooling fan, complete Forced cooling fan for motor type Part number CMP50 13328697 CMP63 13327569 CMP71 13337114 CMP.71 /BP1 /BY2 16447697 CMP80 16444841 CMP80 /BP3 16447751 CMPZ80 /BY4 16447735 CMP100 16444973 CMP.100 /BP5 /BY8 16447808 CMP112 16452178 CMP112 /BY14 16452194 338 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Motor types Additional feature forced-cooling fan 11 Retrofit set for CMP50 to 100 INFORMATION The forced cooling fan retrofit set for CMP50 to CMP63 motors may only be mounted by staff authorized by SEW EURODRIVE. The forced cooling fan retrofit set is supplied as follows: Forced cooling fan, cpl. Accessory bag Retrofit set Content Forced cooling fan, cpl. Machine screw M4x8-Tx-ST-A2F Lock washer Housing cover CMP50 / AS1H / ES1H / RH1M Bolt Washer Housing cover seal for CMP50 Retrofit set Content Forced cooling fan, cpl. Machine screw M4x8-Tx-ST-A2F Lock washer Housing cover CMP63 / AS1H / ES1H / RH1M Bolt Washer Housing cover gasket for CMP63 Retrofit set Part number CMP50 VR kit 13332414 Part number CMP63 VR kit 13332422 11 Content Forced cooling fan, cpl. Cap screw M6x20 8.8 ADB3 Grommet Sleeve Washer Part number CMP71 VR kit Part number CMP.71 /BP1 /BY2 13355228 13355236 Catalog CMP40 CMP112, CMPZ71 CMPZ100 339

11 Motor types Additional feature forced-cooling fan Retrofit set Content Forced cooling fan, cpl. Cap screw M6x20 8.8 ADB3 Grommet Sleeve Washer Part number CMP80 VR kit Part number CMP80 /BP3 Part number CMPZ80 /BY4 13355244 13355252 13355260 Retrofit set Content Forced cooling fan, cpl. Cap screw M6x20 8.8 ADB3 Grommet Sleeve Washer Part number CMP100 VR kit 13355279 13355287 Part number CMP.100 /BP5 /BY8 Retrofit set Content Forced cooling fan, cpl. Cap screw M10x25-8.8-A2F Damping plate Sleeve Washer Part number CMP112 Part number CMP112 /BY14 13368354 13368362 340 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Description 12 12 Prefabricated cables 12.1 Description SEW EURODRIVE offers prefabricated cables with plugs for straightforward and reliable motor connection. Cable and contact are connected using the crimp technique. The following cables are available in steps of 1 m: Motor cables Brakemotor cables Resolver/motor protection cables Absolute encoder/motor protection cables Forced cooling fan cables Prefabricated cables are divided into: Power cables (motor cable, brakemotor cable, extension cable) Feedback cables (encoder cable, extension cable). 12 12.1.1 Preselection of cables Prefabricated cables were preselected by SEW-EURODRIVE according to the standard EN 60204. The routing types "fixed installation" and "cable carrier installation" were considered. Using other standards for the machine construction can result in diverging cross sections. INFORMATION If the system requires UL approval, then the power cables between motor and inverter must have a minimum cross section of 2.5 mm 2 (AWG14) according to NEC430.22 (National Fire Protection Association; Edition 2011). Catalog CMP40 CMP112, CMPZ71 CMPZ100 341

12 Prefabricated cables Project planning for cable cross section 12.2 Project planning for cable cross section 12.2.1 Cable dimensioning to EN 60204 l [m] 150 The following figure shows the minimum required cable cross section depending on cable length and current. 35 mm² 130 25 mm² 110 100 90 2,5 mm² 6 mm² 4 mm² 10 mm² 16 mm² 70 1,5 mm² 50 30 0 10 20 30 40 50 60 70 80 90 100 110 120 130 I [A] 18014403327547531 Prefabricated cables with cross sections of 1.5 mm 2 to 35 mm 2 can be ordered from SEW EURODRIVE. Prefabricated brakemotor cables are available with a cross section of up to 16 mm 2. 342 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Project planning for cable cross section 12 12.2.2 Cable load table Cable load through current I in ampere according to EN 60204 1 (edition 2006) table 6, ambient temperature 40 C. Cable cross section Three-core sheathed cable in pipe or cable (B2) Three-core sheathed cable on top of each other on wall (C) Three-core sheathed cable lined up horizontally (E) mm 2 A A A 1.5 13.1 15.2 16.1 2.5 17.4 21. 22 4 23 28 30 6 30 36 37 10 40 50 52 16 54 66 70 25 70 84 88 35 86 104 110 50 103 125 133 70 130 160 171 12 These data are merely recommended values and are no substitute for the detailed project planning of the incoming cables depending on the specific application considering the applicable regulations. Observe the voltage drop along the cable in particular with the DC 24 V brake coil when dimensioning the cross sections for the brake cable. The acceleration current is decisive for the calculation. 12.2.3 General information on cable assignment tables The values in the cable assignment tables are based on the values with a gray background in the "Cable load tables" ( 2 343). You find the connector assignment in the assignment tables of Connectors and terminal boxes ( 2 316). The limitation of the cable lengths results from the standard specifications relating to the voltage drop at I 0 / I 0VR (< 5 %) for cables according to EN60204-1 (edition 2008) and from the derating of the plug connectors. If the system requires UL approval, then the power cables between motor and inverter must have a minimum cross section of 2.5 mm 2 (AWG14) according to NEC430.22 (National Fire Protection Association; Edition 2011). Catalog CMP40 CMP112, CMPZ71 CMPZ100 343

12 Prefabricated cables Cable assignment: CMP and CMPZ, 400 V system voltage 12.3 Cable assignment: CMP and CMPZ, 400 V system voltage Motor Rated speed Standstill current I 0 The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SM1 6 mm 2 to 16 mm 2 : SMB 16 mm 2 to 35 mm 2 : SMC to cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP40S 3000 1.2 100 1.5 SM1 05904544 05906245 13332457 CMP40S 4500 1.2 100 1.5 SM1 05904544 05906245 13332457 CMP40S 6000 1.2 100 1.5 SM1 05904544 05906245 13332457 CMP40M 3000 0.95 100 1.5 SM1 05904544 05906245 13332457 CMP40M 4500 0.95 100 1.5 SM1 05904544 05906245 13332457 CMP40M 6000 1.1 100 1.5 SM1 05904544 05906245 13332457 CMP50S 3000 0.96 100 1.5 SM1 05904544 05906245 13332457 CMP50S 4500 1.32 100 1.5 SM1 05904544 05906245 13332457 CMP50S 6000 1.7 100 1.5 SM1 05904544 05906245 13332457 CMP50M 3000 1.68 100 1.5 SM1 05904544 05906245 13332457 CMP50M 4500 2.3 100 1.5 SM1 05904544 05906245 13332457 CMP50M 6000 3 100 1.5 SM1 05904544 05906245 13332457 CMP50L 3000 2.2 100 1.5 SM1 05904544 05906245 13332457 CMP50L 4500 3.15 100 1.5 SM1 05904544 05906245 13332457 CMP50L 6000 4.2 100 1.5 SM1 05904544 05906245 13332457 CMP63S 3000 2.15 100 1.5 SM1 05904544 05906245 13332457 CMP63S 4500 3.05 100 1.5 SM1 05904544 05906245 13332457 CMP63S 6000 3.9 100 1.5 SM1 05904544 05906245 13332457 CMP63M 3000 3.6 100 1.5 SM1 05904544 05906245 13332457 CMP63M 4500 5.4 100 1.5 SM1 05904544 05906245 13332457 CMP63M 6000 6.9 100 1.5 SM1 05904544 05906245 13332457 CMP63L 3000 4.95 100 1.5 SM1 05904544 05906245 13332457 CMP63L 4500 6.9 100 1.5 SM1 05904544 05906245 13332457 CMP63L 6000 9.3 75 1.5 SM1 05904544 05906245 13332457 CMP63L 6000 9.3 100 2.5 SM1 05904552 05906253 13332465 CMP.71S 2000 3.4 100 1.5 SM1 05904544 05906245 13332457 CMP.71S 3000 4.9 100 1.5 SM1 05904544 05906245 13332457 CMP.71S 4500 7.3 95 1.5 SM1 05904544 05906245 13332457 CMP.71S 4500 7.3 100 2.5 SM1 05904552 05906253 13332465 CMP.71S 6000 9.6 70 1.5 SM1 05904544 05906245 13332457 CMP.71S 6000 9.6 100 2.5 SM1 05904552 05906253 13332465 CMP.71M 2000 5 100 1.5 SM1 05904544 05906245 13332457 CMP.71M 3000 7.5 90 1.5 SM1 05904544 05906245 13332457 CMP.71M 3000 7.5 100 2.5 SM1 05904552 05906253 13332465 CMP.71M 4500 10.9 65 1.5 SM1 05904544 05906245 13332457 CMP.71M 4500 10.9 100 2.5 SM1 05904552 05906253 13332465 CMP.71M 6000 14.7 80 2.5 SM1 05904552 05906253 13332465 CMP.71M 6000 14.7 100 4 SM1 05904560 05904803 13332473 CMP.71L 2000 6.3 100 1.5 SM1 05904544 05906245 13332457 CMP.71L 3000 9.4 80 1.5 SM1 05904544 05906245 13332457 CMP.71L 3000 9.4 100 2.5 SM1 05904552 05906253 13332465 CMP.71L 4500 14.1 85 2.5 SM1 05904552 05906253 13332465 CMP.71L 4500 14.1 100 4 SM1 05904560 05904803 13332473 CMP.71L 6000 18.8 100 4 SM1 05904560 05904803 13332473 CMP.80S 2000 6.9 100 1.5 SM1 05904544 05906245 13332457 344 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP and CMPZ, 400 V system voltage 12 Motor Rated speed Standstill current I 0 to cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP.80S 3000 10 70 1.5 SM1 05904544 05906245 13332457 CMP.80S 3000 10 100 2.5 SM1 05904552 05906253 13332465 CMP.80S 4500 15.3 80 2.5 SM1 05904552 05906253 13332465 CMP.80S 4500 15.3 100 4 SM1 05904560 05904803 13332473 CMP.80S 6000 20 95 4 SM1 05904560 05904803 13332473 CMP.80S 6000 20 100 6 SMB 13350269 13350293 13350021 CMP.80M 2000 9.3 75 1.5 SM1 05904544 05906245 13332457 CMP.80M 2000 9.3 100 2.5 SM1 05904552 05906253 13332465 CMP.80M 3000 13.4 90 2.5 SM1 05904552 05906253 13332465 CMP.80M 3000 13.4 100 4 SM1 05904560 05904803 13332473 CMP.80M 4500 20.1 95 4 SM1 05904560 05904803 13332473 CMP.80M 4500 20.1 100 6 SMB 13350269 13350293 13350021 CMP.80M 6000 26.4 100 6 SMB 13350269 13350293 13350021 CMP.80L 2000 12.5 90 2.5 SM1 05904552 05906253 13332465 CMP.80L 2000 12.5 100 4 SM1 05904560 05904803 13332473 CMP.80L 3000 18.7 100 4 SM1 05904560 05904803 13332473 CMP.80L 4500 27.8 100 6 SMB 13350269 13350293 13350021 CMP.80L 6000 37.6 100 10 SMB 13350277 13350307 13350048 CMP.100S 2000 13.3 85 2.5 SM1 05904552 05906253 13332465 CMP.100S 2000 13.3 100 4 SM1 05904560 05904803 13332473 CMP.100S 3000 19.6 95 4 SM1 05904560 05904803 13332473 CMP.100S 3000 19.6 100 6 SMB 13350269 13350293 13350021 CMP.100S 4500 30 98 6 SMB 13350269 13350293 13350021 CMP.100S 4500 30 100 10 SMB 13350277 13350307 13350048 CMP.100M 2000 14.7 75 2.5 SM1 05904552 05906253 13332465 CMP.100M 2000 14.7 100 4 SM1 05904560 05904803 13332473 CMP.100M 3000 21.8 85 4 SM1 05904560 05904803 13332473 CMP.100M 3000 21.8 100 6 SMB 13350269 13350293 13350021 CMP.100M 4500 33.1 90 6 SMB 13350269 13350293 13350021 CMP.100M 4500 33.1 100 10 SMB 13350277 13350307 13350048 CMP.100L 2000 21.8 100 6 SMB 13350269 13350293 13350021 CMP.100L 3000 32.3 90 6 SMB 13350269 13350293 13350021 CMP.100L 3000 32.3 100 10 SMB 13350277 13350307 13350048 CMP.100L 4500 48.4 98 10 SMB 13350277 13350307 13350048 CMP.100L 4500 48.4 100 16 SMC 18148476 18148484 18156819 CMP112S 2000 14.3 70 2.5 SM1 05904552 05906253 13332465 CMP112S 2000 14.3 100 4 SM1 05904560 05904803 13332473 CMP112S 3000 21 80 4 SM1 05904560 05904803 13332473 CMP112S 3000 21 100 6 SMB 13350269 13350293 13350021 CMP112S 4500 31.5 80 6 SMB 13350269 13350293 13350021 CMP112S 4500 31.5 100 10 SMB 13350277 13350307 13350048 CMP112M 2000 21 80 4 SM1 05904560 05904803 13332473 CMP112M 2000 21 100 6 SMB 13350269 13350293 13350021 CMP112M 3000 32 80 6 SMB 13350269 13350293 13350021 CMP112M 3000 32 100 10 SMB 13350277 13350307 13350048 CMP112M 4500 47 90 10 SMB 13350277 13350307 13350048 CMP112M 4500 47 100 16 SMB 13350285 13350315 13350056 CMP112M 4500 47 100 16 SMC 18148476 18148484 18156819 CMP112L 2000 33 75 6 SMB 13350269 13350293 13350021 CMP112L 2000 33 100 10 SMB 13350277 13350307 13350048 CMP112L 3000 49 85 10 SMB 13350277 13350307 13350048 CMP112L 3000 49 100 16 SMB 13350285 13350315 13350056 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 345

12 Prefabricated cables Cable assignment: CMP and CMPZ, 400 V system voltage Motor Rated speed Standstill current I 0 to cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP112L 3000 49 100 16 SMC 18148476 18148484 18156819 CMP112L 4500 73 100 25 SMC 18148581 18156827 CMP112H 2000 38 100 10 SMB 13350277 13350307 13350048 CMP112H 3000 57 100 16 SMC 18148476 18148484 18156819 CMP112H 4500 86 100 35 SMC 18148697 18156835 CMP112E 2000 44.5 90 10 SMB 13350277 13350307 13350048 CMP112E 2000 44.5 100 16 SMB 13350285 13350315 13350056 CMP112E 2000 44.5 100 16 SMC 18148476 18148484 18156819 CMP112E 3000 65 80 16 SMC 18148476 18148484 18156819 CMP112E 3000 65 100 25 SMC 18148581 18156827 CMP112E 4500 98 100 35 1) Currently only cable carrier extension cables are offered 346 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP /VR and CMPZ /VR, 400 V system voltage 12 12.4 Cable assignment: CMP /VR and CMPZ /VR, 400 V system voltage Motor Rated speed The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SM1 6 mm 2 to 16 mm 2 : SMB 16 mm 2 to 35 mm 2 : SMC Standstill To cable Core cross current I 0 length section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP50S /VR 3000 1.25 100 1.5 SM1 05904544 05906245 13332457 CMP50S /VR 4500 1.7 100 1.5 SM1 05904544 05906245 13332457 CMP50S /VR 6000 2.2 100 1.5 SM1 05904544 05906245 13332457 CMP50M /VR 3000 2.45 100 1.5 SM1 05904544 05906245 13332457 CMP50M /VR 4500 3.35 100 1.5 SM1 05904544 05906245 13332457 CMP50M /VR 6000 4.4 100 1.5 SM1 05904544 05906245 13332457 CMP50L /VR 3000 3.2 100 1.5 SM1 05904544 05906245 13332457 CMP50L /VR 4500 4.6 100 1.5 SM1 05904544 05906245 13332457 CMP50L /VR 6000 6.1 100 1.5 SM1 05904544 05906245 13332457 CMP63S /VR 3000 3 100 1.5 SM1 05904544 05906245 13332457 CMP63S /VR 4500 4.2 100 1.5 SM1 05904544 05906245 13332457 CMP63S /VR 6000 5.4 100 1.5 SM1 05904544 05906245 13332457 CMP63M /VR 3000 5.1 100 1.5 SM1 05904544 05906245 13332457 CMP63M /VR 4500 7.6 90 1.5 SM1 05904544 05906245 13332457 CMP63M /VR 4500 7.6 100 2.5 SM1 05904552 05906253 13332465 CMP63M /VR 6000 9.8 70 1.5 SM1 05904544 05906245 13332457 CMP63M /VR 6000 9.8 100 2.5 SM1 05904552 05906253 13332465 CMP63L /VR 3000 7.2 95 1.5 SM1 05904544 05906245 13332457 CMP63L /VR 3000 7.2 100 2.5 SM1 05904552 05906253 13332465 CMP63L /VR 4500 10 70 1.5 SM1 05904544 05906245 13332457 CMP63L /VR 4500 10 100 2.5 SM1 05904552 05906253 13332465 CMP63L /VR 6000 13.5 85 2.5 SM1 05904552 05906253 13332465 CMP63L /VR 6000 13.5 100 4 SM1 05904560 05904803 13332473 CMP.71S /VR 2000 4.6 100 1.5 SM1 05904544 05906245 13332457 CMP.71S /VR 3000 6.7 100 1.5 SM1 05904544 05906245 13332457 CMP.71S /VR 4500 9.9 70 1.5 SM1 05904544 05906245 13332457 CMP.71S /VR 4500 9.9 100 2.5 SM1 05904552 05906253 13332465 CMP.71S /VR 6000 13.1 85 2.5 SM1 05904552 05906253 13332465 CMP.71S /VR 6000 13.1 100 4 SM1 05904560 05904803 13332473 CMP.71M /VR 2000 7.3 95 1.5 SM1 05904544 05906245 13332457 CMP.71M /VR 2000 7.3 100 2.5 SM1 05904552 05906253 13332465 CMP.71M/VR 3000 10.9 60 1.5 SM1 05904544 05906245 13332457 CMP.71M /VR 3000 10.9 100 2.5 SM1 05904552 05906253 13332465 CMP.71M /VR 4500 15.9 70 2.5 SM1 05904552 05906253 13332465 CMP.71M /VR 4500 15.9 100 4 SM1 05904560 05904803 13332473 CMP.71M /VR 6000 21.5 85 4 SM1 05904560 05904803 13332473 CMP.71M /VR 6000 21.5 100 6 SMB 13350269 13350293 13350021 CMP.71L /VR 2000 10.1 65 1.5 SM1 05904544 05906245 13332457 CMP.71L /VR 2000 10.1 100 2.5 SM1 05904552 05906253 13332465 CMP.71L /VR 3000 15.1 75 2.5 SM1 05904552 05906253 13332465 CMP.71L /VR 3000 15.1 100 4 SM1 05904560 05904803 13332473 CMP.80S /VR 2000 9.5 70 1.5 SM1 05904544 05906245 13332457 CMP.80S /VR 2000 9.5 100 2.5 SM1 05904552 05906253 13332465 CMP.80S /VR 3000 13.8 80 2.5 SM1 05904552 05906253 13332465 CMP.80S /VR 3000 13.8 100 4 SM1 05904560 05904803 13332473 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 347

12 Prefabricated cables Cable assignment: CMP /VR and CMPZ /VR, 400 V system voltage Motor Rated speed Standstill current I 0 To cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP.80S /VR 4500 21 85 4 SM1 05904560 05904803 13332473 CMP.80S /VR 4500 21 100 6 SMB 13350269 13350293 13350021 CMP.80S /VR 6000 27.5 100 6 SMB 13350269 13350293 13350021 CMP.80M /VR 2000 13.4 85 2.5 SM1 05904552 05906253 13332465 CMP.80M /VR 2000 13.4 100 4 SM1 05904560 05904803 13332473 CMP.80M /VR 3000 19.3 95 4 SM1 05904560 05904803 13332473 CMP.80M /VR 3000 19.3 100 6 SMB 13350269 13350293 13350021 CMP.80M /VR 4500 29 95 6 SMB 13350269 13350293 13350021 CMP.80M /VR 4500 29 100 10 SMB 13350277 13350307 13350048 CMP.80M /VR 6000 38 100 10 SMB 13350277 13350307 13350048 CMP.80L /VR 2000 20 90 4 SM1 05904560 05904803 13332473 CMP.80L /VR 2000 20 100 6 SMB 13350269 13350293 13350021 CMP.80L /VR 3000 30 90 6 SMB 13350269 13350293 13350021 CMP.80L /VR 3000 30 100 10 SMB 13350277 13350307 13350048 CMP.80L /VR 4500 44.5 100 10 SMB 13350277 13350307 13350048 CMP.100S /VR 2000 18.8 95 4 SM1 05904560 05904803 13332473 CMP.100S /VR 2000 18.8 100 6 SMB 13350269 13350293 13350021 CMP.100S /VR 3000 27.5 100 6 SMB 13350269 13350293 13350021 CMP.100S /VR 4500 42.5 100 10 SMB 13350277 13350307 13350048 CMP.100M /VR 2000 22.3 100 6 SMB 13350269 13350293 13350021 CMP.100M /VR 3000 33 85 6 SMB 13350269 13350293 13350021 CMP.100M /VR 3000 33 100 10 SMB 13350277 13350307 13350048 CMP.100M /VR 4500 72 100 35 SMC 18148697 CMP.100M/ VR 4500 50 100 16 SMB 13350285 13350315 13350056 CMP.100M/ VR 4500 50 100 16 SMC 18148476 18148484 18156819 CMP.100L /VR 2000 32.5 85 6 SMB 13350269 13350293 13350021 CMP.100L /VR 2000 32.5 100 10 SMB 13350277 13350307 13350048 CMP.100L /VR 3000 48 95 10 SMB 13350277 13350307 13350048 CMP.100L /VR 3000 48 100 16 SMB 13350285 13350315 13350056 CMP.100L/VR 4500 72 100 25 SMC 18148581 18156827 CMP112S/ VR 2000 21 80 4 SM1 05904560 05904803 13332473 CMP112S/ VR 2000 21 100 6 SMB 13350269 13350293 13350021 CMP112S/ VR 3000 30.5 80 6 SMB 13350269 13350293 13350021 CMP112S/ VR 3000 30.5 100 10 SMB 13350277 13350307 13350048 CMP112S/ VR 4500 45.5 90 10 SMB 13350277 13350307 13350048 CMP112S/ VR 4500 45.5 100 16 SMB 13350285 13350315 13350056 CMP112S/ VR 4500 45.5 100 16 SMC 18148476 18148484 18156819 CMP112M/ VR 2000 32 80 6 SMB 13350269 13350293 13350021 CMP112M/ VR 2000 32 100 10 SMB 13350277 13350307 13350048 CMP112M/ VR 3000 49 85 10 SMB 13350277 13350307 13350048 CMP112M/ VR 3000 49 100 16 SMB 13350285 13350315 13350056 CMP112M/ VR 3000 49 100 16 SMC 18148476 18148484 18156819 CMP112M/ VR 4500 72 100 25 SMC 18148581 18156827 CMP112L/ VR 2000 52 100 16 SMC 18148476 18148484 18156819 CMP112L/ VR 3000 77 100 25 SMC 18148581 18156827 CMP112L/ VR 4500 114 100 50 CMP112H/ VR 2000 57 100 16 SMC 18148476 18148484 18156819 CMP112H/ VR 3000 84 100 35 SMC 18148697 18156835 CMP112H/ VR 4500 128 100 50 CMP112E/ VR 2000 71 100 25 SMC 18148581 18156827 CMP112E/ VR 3000 104 100 35 348 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP /VR and CMPZ /VR, 400 V system voltage 12 Motor Rated speed Standstill current I 0 To cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP112E/ VR 4500 156 100 50 1) Currently only cable carrier extension cables are offered 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 349

12 Prefabricated cables Cable assignment: CMP /BP /BK, 400 V system voltage 12.5 Cable assignment: CMP /BP /BK, 400 V system voltage Motor Rated speed The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB Standstill To cable current I 0 length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP40S /BK 3000 1.2 100 1.5 SB1 13354345 13354388 13354221 CMP40S /BK 4500 1.2 100 1.5 SB1 13354345 13354388 13354221 CMP40S /BK 6000 1.2 100 1.5 SB1 13354345 13354388 13354221 CMP40M /BK 3000 0.95 100 1.5 SB1 13354345 13354388 13354221 CMP40M /BK 4500 0.95 100 1.5 SB1 13354345 13354388 13354221 CMP40M /BK 6000 1.1 100 1.5 SB1 13354345 13354388 13354221 CMP50S /BK 3000 0.96 100 1.5 SB1 13354345 13354388 13354221 CMP50S /BK 4500 1.32 100 1.5 SB1 13354345 13354388 13354221 CMP50S /BK 6000 1.7 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK 3000 1.68 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK 4500 2.3 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK 6000 3 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK 3000 2.2 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK 4500 3.15 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK 6000 4.2 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK 3000 2.15 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK 4500 3.05 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK 6000 3.9 100 1.5 SB1 13354345 13354388 13354221 CMP63M /BK 3000 3.6 100 1.5 SB1 13354345 13354388 13354221 CMP63M /BK 4500 5.4 100 1.5 SB1 13354345 13354388 13354221 CMP63M /BK 6000 6.9 100 1.5 SB1 13354345 13354388 13354221 CMP63L /BK 3000 4.95 100 1.5 SB1 13354345 13354388 13354221 CMP63L /BK 4500 6.9 100 1.5 SB1 13354345 13354388 13354221 CMP63L /BK 6000 9.3 75 1.5 SB1 13354345 13354388 13354221 CMP63L /BK 6000 9.3 100 2.5 SB1 13354353 13354396 13354248 CMP71S /BP 2000 3.4 80 1.5 SB1 13354345 13354388 13354221 CMP71S /BP 3000 4.9 80 1.5 SB1 13354345 13354388 13354221 CMP71S /BP 4500 7.3 80 1.5 SB1 13354345 13354388 13354221 CMP71S /BP 4500 7.3 80 2.5 SB1 13354353 13354396 13354248 CMP71S /BP 6000 9.6 70 1.5 SB1 13354345 13354388 13354221 CMP71S /BP 6000 9.6 80 2.5 SB1 13354353 13354396 13354248 CMP71M /BP 2000 5 80 1.5 SB1 13354345 13354388 13354221 CMP71M /BP 3000 7.5 80 1.5 SB1 13354345 13354388 13354221 CMP71M /BP 3000 7.5 80 2.5 SB1 13354353 13354396 13354248 CMP71M /BP 4500 10.9 65 1.5 SB1 13354345 13354388 13354221 CMP71M /BP 4500 10.9 80 2.5 SB1 13354353 13354396 13354248 CMP71M /BP 6000 14.7 80 2.5 SB1 13354353 13354396 13354248 CMP71M /BP 6000 14.7 80 4 SB1 13354361 13421603 13354337 CMP71L /BP 2000 6.3 80 1.5 SB1 13354345 13354388 13354221 CMP71L /BP 3000 9.4 80 1.5 SB1 13354345 13354388 13354221 CMP71L /BP 3000 9.4 80 2.5 SB1 13354353 13354396 13354248 CMP71L /BP 4500 14.1 80 2.5 SB1 13354353 13354396 13354248 CMP71L /BP 4500 14.1 80 4 SB1 13354361 13421603 13354337 CMP71L /BP 6000 18.8 80 4 SB1 13354361 13421603 13354337 CMP80S /BP 2000 6.9 55 1.5 SB1 13354345 13354388 13354221 CMP80S /BP 2) 3000 10 55 1.5 SB1 1335 4345 1335 4388 1335 4221 350 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP /BP /BK, 400 V system voltage 12 Motor Rated speed Standstill current I 0 To cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP80S /BP 3000 10 55 2.5 SB1 1335 4353 1335 4396 1335 4248 CMP80S /BP 4500 15.3 55 2.5 SB1 1335 4353 1335 4396 1335 4248 CMP80S /BP 4500 15.3 55 4 SB1 1335 4361 13421603 1335 4337 CMP80M /BP 2000 9.3 55 1.5 SB1 1335 4345 1335 4388 1335 4221 CMP80M /BP 2000 9.3 55 2.5 SB1 1335 4353 1335 4396 1335 4248 CMP80M /BP 3000 13.4 55 2.5 SB1 1335 4353 1335 4396 1335 4248 CMP80M /BP 3000 13.4 55 4 SB1 1335 4361 13421603 1335 4337 CMP80M /BP 4500 20.1 55 4 SB1 1335 4361 13421603 1335 4337 CMP80M /BP 4500 20.1 85 6 SBB 1335 0196 1335 0234 1335 0099 CMP80L /BP 2000 12.5 55 2.5 SB1 1335 4353 1335 4396 1335 4248 CMP80L /BP 2000 12.5 55 4 SB1 1335 4361 13421603 1335 4337 CMP80L /BP 3000 18.7 55 4 SB1 1335 4361 13421603 1335 4337 CMP80L /BP 4500 27.8 85 6 SB1 1335 0196 1335 0234 1335 0099 CMP100S /BP 2000 13.3 45 2.5 SB1 1335 4353 1335 4396 1335 4248 CMP100S /BP 2000 13.3 45 4 SB1 1335 4361 13421603 1335 4337 CMP100S /BP 3000 19.6 45 4 SB1 1335 4361 13421603 1335 4337 CMP100S /BP 3000 19.6 70 6 SBB 1335 0196 1335 0234 1335 0099 CMP100S /BP 4500 30 70 6 SBB 1335 0196 1335 0234 1335 0099 CMP100S /BP 4500 30 70 10 SBB 1335 0218 1335 0242 1335 0102 CMP100M /BP 2000 14.7 45 2.5 SB1 1335 4353 1335 4396 1335 4248 CMP100M /BP 2000 14.7 45 4 SB1 1335 4361 13421603 1335 4337 CMP100M /BP 3000 21.8 45 4 SB1 1335 4361 13421603 1335 4337 CMP100M /BP 3000 21.8 70 6 SBB 1335 0196 03350234 1335 0099 CMP100M /BP 4500 33.1 70 6 SBB 1335 0196 1335 0234 1335 0099 CMP100M /BP 4500 33.1 70 10 SBB 1335 0218 1335 0242 1335 0102 CMP100L /BP 2000 21.8 70 6 SBB 1335 0196 1335 0234 1335 0099 CMP100L /BP 3000 32.3 70 6 SBB 1335 0196 1335 0234 1335 0099 CMP100L /BP 3000 32.3 70 10 SBB 1335 0218 1335 0242 1335 0102 CMP100L /BP 4500 48.4 70 10 SBB 1335 0218 1335 0242 1335 0102 CMP100L /BP 4500 48.4 70 16 SBB 1335 0226 1335 0250 1335 0110 1) Currently only cable carrier extension cables are offered 2) The maximum cable length can be increased to 70 m or 85 m if a cable with a core cross section of 6 mm is used (change from SB1 to SBB). In this case, the brake cable cross section increases from 1 mm to 1.5 mm 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 351

12 Prefabricated cables Cable assignment: CMP /BP / BK /VR, 400 V system voltage 12.6 Cable assignment: CMP /BP / BK /VR, 400 V system voltage Motor The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB Rated Standstill To cable Core speed current I 0 length cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP50S /BK /VR 3000 1.25 100 1.5 SB1 13354345 13354388 13354221 CMP50S /BK /VR 4500 1.7 100 1.5 SB1 13354345 13354388 13354221 CMP50S /BK /VR 6000 2.2 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK. /VR 3000 2.45 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK /VR 4500 3.35 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK /VR 6000 4.4 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK /VR 3000 3.2 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK /VR 4500 4.6 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK /VR 6000 6.1 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK /VR 3000 3 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK /VR 4500 4.2 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK /VR 6000 5.4 100 1.5 SB1 13354345 13354388 13354221 CMP63M /BK /VR 3000 5.1 100 1.5 SB1 13354345 13354388 13354221 CMP63M /BK /VR 4500 7.6 90 1.5 SB1 13354345 13354388 13354221 CMP63M /BK /VR 4500 7.6 100 2.5 SB1 13354353 13354396 13354248 CMP63M /BK /VR 6000 9.8 70 1.5 SB1 13354345 13354388 13354221 CMP63M /BK /VR 6000 9.8 100 2.5 SB1 13354353 13354396 13354248 CMP63L /BK /VR 3000 7.2 95 1.5 SB1 13354345 13354388 13354221 CMP63L /BK /VR 3000 7.2 100 2.5 SB1 13354353 13354396 13354248 CMP63L /BK /VR 4500 10 70 1.5 SB1 13354345 13354388 13354221 CMP63L /BK /VR 4500 10 100 2.5 SB1 13354353 13354396 13354248 CMP63L /BK /VR 6000 13.5 85 2.5 SB1 13354353 13354396 13354248 CMP63L /BK /VR 6000 13.5 100 4 SB1 13354361 13421603 13354337 CMP71S /BP /VR 2000 4.6 80 1.5 SB1 13354345 13354388 13354221 CMP71S /BP /VR 3000 6.7 80 1.5 SB1 13354345 13354388 13354221 CMP71S /BP /VR 4500 9.9 70 1.5 SB1 13354345 13354388 13354221 CMP71S /BP /VR 4500 9.9 80 2.5 SB1 13354353 13354396 13354248 CMP71S /BP /VR 6000 13.1 80 2.5 SB1 13354353 13354396 13354248 CMP71S /BP /VR 6000 13.1 80 4 SB1 13354361 13421603 13354337 CMP71M /BP /VR 2000 7.3 80 1.5 SB1 13354345 13354388 13354221 CMP71M /BP /VR 2000 7.3 80 2.5 SB1 13354353 13354396 13354248 CMP71M /BP /VR 3000 10.9 60 1.5 SB1 13354345 13354388 13354221 CMP71M /BP /VR 3000 10.9 80 2.5 SB1 13354353 13354396 13354248 CMP71M /BP /VR 4500 15.9 70 2.5 SB1 13354353 13354396 13354248 CMP71M /BP /VR 4500 15.9 80 4 SB1 13354361 13421603 13354337 CMP71M /BP /VR 6000 21.5 80 4 SB1 13354361 13421603 13354337 CMP71L /BP /VR 2000 10.1 65 1.5 SB1 13354345 13354388 13354221 CMP71L /BP /VR 2000 10.1 100 2.5 SB1 13354353 13354396 13354248 CMP71L /BP /VR 3000 15.1 75 2.5 SB1 13354353 13354396 13354248 CMP71L /BP /VR 3000 15.1 80 4 SB1 13354361 13421603 13354337 CMP80S /BP /VR 2000 9.5 55 1.5 SB1 13354345 13354388 13354221 CMP80S /BP /VR 2000 9.5 55 2.5 SB1 13354353 13354396 13354248 CMP80S /BP 2) /VR 3000 13.8 55 2.5 SB1 13354353 13354396 13354248 CMP80S /BP /VR 3000 13.8 55 4 SB1 13354361 13421603 13354337 CMP80S /BP /VR 4500 21 55 4 SB1 13354361 13421603 13354337 CMP80S /BP /VR 4500 21 85 6 SBB 13350196 13350234 13350099 352 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP /BP / BK /VR, 400 V system voltage 12 Motor Rated speed Standstill current I 0 To cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP80M /BP /VR 2000 13.4 55 2.5 SB1 13354353 13354396 13354248 CMP80M /BP /VR 2000 13.4 50 4 SB1 13354361 13421603 13354337 CMP80M /BP /VR 3000 19.3 55 4 SB1 13354361 13421603 13354337 CMP80M /BP /VR 3000 19.3 85 6 SBB 13350196 13350234 13350099 CMP80M /BP /VR 4500 29 85 6 SBB 13350196 13350234 13350099 CMP80M /BP /VR 4500 29 85 10 SBB 13350218 13350242 13350102 CMP80L /BP /VR 2000 20 55 4 SB1 13354361 13421603 13354337 CMP80L /BP /VR 2000 20 85 6 SBB 13350196 13350234 13350099 CMP80L /BP /VR 3000 30 85 6 SBB 13350196 13350234 13350099 CMP80L /BP /VR 3000 30 85 10 SBB 13350218 13350242 13350102 CMP80L /BP /VR 4500 44.5 85 10 SBB 13350218 13350242 13350102 CMP100S /BP /VR 2000 18.8 45 4 SB1 13354361 13421603 13354337 CMP100S /BP /VR 2000 18.8 70 6 SBB 13350196 13350234 13350099 CMP100S /BP /VR 3000 27.5 70 6 SBB 13350196 13350234 13350099 CMP100S /BP /VR 4500 42.5 70 10 SBB 13350218 13350242 13350102 CMP100M /BP /VR 2000 22.3 70 6 SBB 13350196 13350234 13350099 CMP100M /BP /VR 3000 33 70 6 SBB 13350196 13350234 13350099 CMP100M /BP /VR 3000 33 70 10 SBB 13350218 13350242 13350102 CMP100L /BP /VR 2000 32.5 70 6 SBB 13350196 13350234 13350099 CMP100L /BP /VR 2000 32.5 70 10 SBB 13350218 13350242 13350102 CMP100L /BP /VR 3000 48 70 10 SBB 13350218 13350242 13350102 CMP100L /BP /VR 3000 48 70 16 SBB 13350226 13350250 13350110 1) Currently only cable carrier extension cables are offered 2) The maximum cable length can be increased to 70 m or 85 m if a cable with a core cross section of 6 mm is used (change from SB1 to SBB connector). In this case, the brake cable cross section increases from 1 mm to 1.5 mm. 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 353

12 Prefabricated cables Cable assignment: CMP /BY, 400 V system voltage 12.7 Cable assignment: CMP /BY, 400 V system voltage The following table allows for selecting power cables for CMP servo brakemotors with a system voltage of 400 V and a BY brake with 400 V, 230 V or 110 V brake voltage. An additional length for 110 V is specified in parenthesis for cases where the permitted cable length for 110 V is shorter than for 400 V/230 V. The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB Motor Rated speed Standstill current I 0 16 mm 2 to 35 mm 2 : SBC To cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP112S/ BY 2000 14.3 50 2.5 SB1 13354280 13354310 13354248 CMP112S/ BY 3000 21 50 4 SB1 13354299 13354329 13354337 CMP112S/ BY 4500 31.5 80 6 SBB 13350129 13350153 13350099 CMP112M/ BY 2000 21 50 4 SB1 13354299 13354329 13354337 CMP112M/ BY 3000 32 80 6 SBB 13350129 13350153 13350099 CMP112M/ BY 4500 47 80 10 SBB 13350137 13350161 13350102 CMP112L/ BY 2000 33 75 6 SBB 13350129 13350153 13350099 CMP112L/ BY 2000 33 80 10 SBB 13350137 13350161 13350102 CMP112L/ BY 3000 49 80 10 SBB 13350137 13350161 13350102 CMP112L/ BY 4500 73 80 25 SBC CMP112H/ BY 2000 38 80 10 SBB 13350137 13350161 13350102 CMP112H/ BY 3000 57 80 16 SBC 18148514 18148522 18156843 CMP112H/ BY 4500 86 80 35 CMP112E/ BY 2000 44.5 80 10 SBB 13350137 13350161 13350102 CMP112E/ BY 3000 65 80 16 SBC 18148514 18148522 18156843 CMP112E/ BY 4500 98 80 35 1) Currently only cable carrier extension cables are offered Permitted cable lengths for DC 24 V BY working brakes are especially reduced. Note the following guidelines: CMP112 /BY: between 4 and 6 m depending on the cable cross section For project planning with DC 24 V BY working brake, consult SEW EURODRIVE. 354 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP /BY /VR, 400 V system voltage 12 12.8 Cable assignment: CMP /BY /VR, 400 V system voltage Motor The following table allows for selecting power cables for CMP servo brakemotors with a system voltage of 400 V and a BY brake with 400 V, 230 V or 110 V brake voltage. An additional length for 110 V is specified in parenthesis for cases where the permitted cable length for 110 V is shorter than for 400 V/230 V. The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB 16 mm 2 to 35 mm 2 : SBC Standstill To cable current I 0 length Rated speed Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP112S/ BY/ VR 2000 21 50 4 SB1 13354299 13354329 13354337 CMP112S/ BY/ VR 3000 30.5 80 6 SBB 13350137 13350153 13350099 CMP112S/ BY/ VR 4500 45.5 80 10 SBB 13350137 13350161 13350102 CMP112M/ BY/ VR 2000 32 80 6 SBB 13350137 13350153 13350099 CMP112M/ BY/ VR 3000 49 80 10 SBB 13350137 13350161 13350102 CMP112M/ BY/ VR 4500 72 80 25 SBC CMP112L/BY/ VR 2000 52 80 16 SBC 18148514 18148522 18156843 CMP112L/BY/ VR 3000 77 80 25 SBC CMP112L/BY/ VR 4500 114 80 50 CMP112H/ BY/ VR 2000 57 80 16 SBC 18148514 18148522 18156843 CMP112H/ BY/ VR 3000 84 80 35 SBC CMP112H/ BY/ VR 4500 128 80 50 CMP112E/ BY/ VR 2000 71 80 25 SBC CMP112E/ BY/ VR 3000 104 80 35 CMP112E/ BY/ VR 4500 156 80 50 1) Currently only cable carrier extension cables are offered 12 Permitted cable lengths for DC 24 V BY working brakes are especially reduced. Note the following guidelines: CMP112 /BY: between 4 and 6 m depending on the cable cross section For project planning with DC 24 V BY working brake, consult SEW EURODRIVE. Catalog CMP40 CMP112, CMPZ71 CMPZ100 355

12 Prefabricated cables Cable assignment: CMPZ /BY, 400 V system voltage 12.9 Cable assignment: CMPZ /BY, 400 V system voltage Motor Rated speed The following table allows for selecting power cables for CMP servo brakemotors with a system voltage of 400 V and a BY brake with 400 V, 230 V or 110 V brake voltage. An additional length for 110 V is specified in parenthesis for cases where the permitted cable length for 110 V is shorter than for 400 V/230 V. The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SM1 6 mm 2 to 16 mm 2 : SMB 16 mm 2 to 35 mm 2 : SMC Standstill To cable current I 0 length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMPZ71S /BY 2000 3.4 100 1.5 SM1 13354272 13354302 13354221 CMPZ71S /BY 3000 4.9 100 1.5 SM1 13354272 13354302 13354221 CMPZ71S /BY 4500 7.3 96 1.5 SM1 13354272 13354302 13354221 CMPZ71S /BY 4500 7.3 100 2.5 SM1 13354280 13354310 13354248 CMPZ71S /BY 6000 9.6 73 1.5 SM1 13354272 13354302 13354221 CMPZ71S /BY 6000 9.6 100 2.5 SM1 13354280 13354310 13354248 CMPZ71M /BY 2000 5 100 1.5 SM1 13354272 13354302 13354221 CMPZ71M /BY 3000 7.5 93 1.5 SM1 13354272 13354302 13354221 CMPZ71M /BY 3000 7.5 100 2.5 SM1 13354280 13354310 13354248 CMPZ71M /BY 4500 10.9 64 1.5 SM1 13354272 13354302 13354221 CMPZ71M /BY 4500 10.9 100 2.5 SM1 1335 4280 13354310 13354248 CMPZ71M /BY 6000 14.7 79 2.5 SM1 1335 4280 13354310 13354248 CMPZ71M /BY 6000 14.7 100 4 SM1 1335 4299 13354329 13354337 CMPZ71L /BY 2000 6.3 100 1.5 SM1 1335 4272 13354302 13354221 CMPZ71L /BY 3000 9.4 74 1.5 SM1 1335 4272 13354302 13354221 CMPZ71L /BY 3000 9.4 100 2.5 SM1 1335 4280 13354310 13354248 CMPZ 71L /BY 4500 14.1 83 2.5 SM1 1335 4280 13354310 13354248 CMPZ 71L /BY 4500 14.1 100 4 SM1 1335 4299 13354329 13354337 CMPZ71L /BY 6000 18.8 100 4 SM1 1335 4299 13354329 13354337 CMPZ80S /BY 2000 6.9 100 1.5 SM1 1335 4272 13354302 13354221 CMPZ80S /BY 3000 10 70 1.5 SM1 1335 4272 13354302 13354221 CMPZ80S /BY 3000 10 100 (75) 2.5 SM1 1335 4280 13354310 13354248 CMPZ80S /BY 4500 15.3 76 (75) 2.5 SM1 1335 4280 13354310 13354248 CMPZ80S /BY 4500 15.3 100 (75) 4 SM1 1335 4299 13354329 13354337 CMPZ80M /BY 2000 9.3 75 1.5 SM1 1335 4272 13354302 13354221 CMPZ80M /BY 2000 9.3 100 2.5 SM1 1335 4280 13354310 13354248 CMPZ80M /BY 3000 13.4 87 (75) 2.5 SM1 1335 4280 13354310 13354248 CMPZ80M /BY 3000 13.4 100 (75) 4 SM1 1335 4299 13354329 13354337 CMPZ80M /BY 4500 20.1 93 (75) 4 SM1 1335 4299 13354329 13354337 CMPZ80M /BY 4500 20.1 100 6 SMB 1335 0129 13350153 13350099 CMPZ80L /BY 2000 12.5 93 2.5 SM1 1335 4280 13354310 13354248 CMPZ80L /BY 2000 12.5 100 4 SM1 1335 4299 13354329 13354337 CMPZ80L /BY 3000 18.7 100 (75) 4 SM1 1335 4299 13354329 13354337 CMPZ80L /BY 4500 27.8 100 6 SMB 1335 0129 13350153 13350099 CMPZ100S /BY 2000 13.3 88 2.5 SM1 1335 4280 13354310 13354248 CMPZ100S /BY 2000 13.3 100 4 SM1 1335 4299 13354329 13354337 CMPZ100S /BY 3000 19.6 95 (55) 4 SM1 1335 4299 13354329 13354337 CMPZ100S /BY 3000 19.6 100 (80) 6 SMB 1335 0129 13350153 13350099 CMPZ100S /BY 4500 30 93 (80) 6 SMB 1335 0129 13350153 13350099 CMPZ100S /BY 4500 30 100 (80) 10 SMB 1335 0137 13350161 13350102 356 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMPZ /BY, 400 V system voltage 12 Motor Rated speed Standstill current I 0 To cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMPZ100M /BY 2000 14.7 79 2.5 SM1 1335 4280 13354310 13354248 CMPZ100M /BY 2000 14.7 100 4 SM1 1335 4299 13354329 13354337 CMPZ100M /BY 3000 21.8 85 (55) 4 SM1 1335 4299 13354329 13354337 CMPZ100M /BY 3000 21.8 100 (80) 6 SMB 1335 0129 13350153 13350099 CMPZ100M /BY 4500 33.1 84 (80) 6 SMB 13350129 13350153 13350099 CMPZ100M /BY 4500 33.1 100 (80) 10 SMB 13350137 13350161 13350102 CMPZ100L /BY 2000 21.8 85 4 SM1 13354299 13354329 13354337 CMPZ100L /BY 2000 21.8 100 6 SMB 13350129 13350153 13350099 CMPZ100L /BY 3000 32.3 87 (80) 6 SMB 13350129 13350153 13350099 CMPZ100L /BY 3000 32.3 100 (80) 10 SMB 13350137 13350161 13350102 CMPZ100L /BY 4500 48.4 96 (80) 10 SMB 13350137 13350161 13350102 CMPZ100L /BY 4500 48.4 100 (80) 16 SMB 13350145 13350188 13350110 CMPZ100L /BY 4500 48.4 100 (80) 16 SBC 18148514 18148522 18156843 1) Currently only cable carrier extension cables are offered 12 Permitted cable lengths for DC 24 V BY working brakes are especially reduced. Note the following guidelines: CMPZ71. /BY: maximum 8 m CMPZ80. between 6.4 and 9 m depending on the cable cross section CMPZ100. /BY: between 4.5 and 7 m depending on the cable cross section For project planning with DC 24 V BY working brake, consult SEW EURODRIVE. Catalog CMP40 CMP112, CMPZ71 CMPZ100 357

12 Prefabricated cables Cable assignment: CMPZ /BY /VR, 400 V system voltage 12.10 Cable assignment: CMPZ /BY /VR, 400 V system voltage Motor The following table allows for selecting power cables for CMP servo brakemotors with a system voltage of 400 V and a BY brake with 400 V, 230 V or 110 V brake voltage. An additional length for 110 V is specified in parenthesis for cases where the permitted cable length for 110 V is shorter than for 400 V/230 V. The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB 16 mm 2 to 35 mm 2 : SBC Standstill To cable current I 0 length Rated speed Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMPZ71S /BY /VR 2000 4.6 100 1.5 SB1 13354272 13354302 13354221 CMPZ71S /BY /VR 3000 6.7 100 1.5 SB1 13354272 13354302 13354221 CMPZ71S /BY /VR 4500 9.9 70 1.5 SB1 13354272 13354302 13354221 CMPZ71S /BY /VR 4500 9.9 100 2.5 SB1 13354280 13354310 13354248 CMPZ71S /BY /VR 6000 13.1 89 2.5 SB1 13354280 13354310 13354248 CMPZ71S /BY /VR 6000 13.1 100 4 SB1 13354299 13354329 13354337 CMPZ71M /BY /VR 2000 7.3 96 1.5 SB1 13354272 13354302 13354221 CMPZ71M /BY /VR 2000 7.3 100 2.5 SB1 13354280 13354310 13354248 CMPZ71M /BY /VR 3000 10.9 64 1.5 SB1 13354272 13354302 13354221 CMPZ71M /BY /VR 3000 10.9 100 2.5 SB1 13354280 13354310 13354248 CMPZ71M /BY /VR 4500 15.9 73 2.5 SB1 13354280 13354310 13354248 CMPZ71M /BY /VR 4500 15.9 100 4 SB1 13354299 13354329 13354337 CMPZ71M /BY /VR 6000 21.5 85 4 SB1 13354299 13354329 13354337 CMPZ71M /BY /VR 6000 21.5 100 6 SBB 13350129 13350153 13350099 CMPZ71L /BY /VR 2000 10.1 69 1.5 SB1 13354272 13354302 13354221 CMPZ71L /BY /VR 2000 10.1 100 2.5 SB1 13354280 13354310 13354248 CMPZ71L /BY /VR 3000 15.1 76 2.5 SB1 13354280 13354310 13354248 CMPZ71L /BY /VR 3000 15.1 100 4 SB1 13354299 13354329 13354337 CMPZ 71L /BY /VR 4500 22.5 100 6 SBB 13350129 13350153 13350099 CMPZ71L /BY /VR 6000 30 93 6 SBB 13350129 13350153 13350099 CMPZ71L /BY /VR 6000 30 100 10 SB1 1335 0137 1335 0161 1335 0102 CMPZ80S /BY /VR 2000 9.5 73 1.5 SB1 13354272 13354302 13354221 CMPZ80S /BY /VR 2000 9.5 100 2.5 SB1 13354280 13354310 13354248 CMPZ80S /BY /VR 3000 13.8 84 2.5 SB1 13354280 13354310 13354248 CMPZ80S /BY /VR 3000 13.8 100 4 SB1 13354299 13354329 13354337 CMPZ80S /BY /VR 4500 21 89 4 SB1 13354299 13354329 13354337 CMPZ80S /BY /VR 4500 21 100 6 SBB 13350129 13350153 13350099 CMPZ80S /BY /VR 6000 27.5 100 6 SBB 13350129 13350153 13350099 CMPZ80M /BY /VR 2000 13.4 87 2.5 SB1 13354280 13354310 13354248 CMPZ80M /BY /VR 2000 13.4 100 4 SB1 13354299 13354329 13354337 CMPZ80M /BY /VR 3000 19.3 97 4 SB1 13354299 13354329 13354337 CMPZ80M /BY /VR 3000 19.3 100 6 SB1 13350129 13350153 13350099 CMPZ80M /BY /VR 4500 29 96 6 SBB 13350129 13350153 13350099 CMPZ80M /BY /VR 4500 29 100 10 SBB 13350137 13350161 13350102 CMPZ80M /BY /VR 6000 38 100 10 SBB 13350137 13350161 13350102 CMPZ80L /BY /VR 2000 20 93 4 SB1 13354299 13354329 13354337 CMPZ80L /BY /VR 2000 20 100 6 SBB 13350129 13350153 13350099 CMPZ80L /BY /VR 3000 30 93 6 SBB 13350129 13350153 13350099 CMPZ80L /BY /VR 3000 30 100 10 SBB 13350137 13350161 13350102 CMPZ80L /BY /VR 4500 44.5 100 10 SBB 13350137 13350161 13350102 358 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMPZ /BY /VR, 400 V system voltage 12 Motor Rated speed Standstill current I 0 To cable length Core Plug connector cross section Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMPZ80L /BY /VR 6000 60 100 16 SBB 13350145 13350188 13350110 CMPZ100S /BY /VR 2000 18.8 100 4 SBB 13354299 13354329 13354337 CMPZ100S /BY /VR 3000 27.5 100 6 SBB 13350129 13350153 13350099 CMPZ100S /BY /VR 4500 42.5 100 10 SBB 13350137 13350161 13350102 CMPZ100M /BY /VR 2000 22.3 100 6 SBB 13350129 13350153 13350099 CMPZ100M /BY /VR 3000 33 84 6 SBB 13350129 13350153 13350099 CMPZ100M /BY /VR 3000 33 100 10 SBB 13350137 13350161 13350102 CMPZ100M /BY /VR 4500 50 100 16 SBC 18148514 18148522 18156843 CMPZ100L /BY /VR 2000 32.5 86 6 SBB 1335 0129 13350153 13350099 CMPZ100L /BY /VR 2000 32.5 100 10 SBB 1335 0137 13350161 13350102 CMPZ100L /BY /VR 3000 48 97 10 SBB 1335 0137 13350161 13350102 CMPZ100L /BY /VR 3000 48 100 16 SBB 1335 0145 13350188 13350110 CMPZ100L /BY /VR 3000 48 100 16 SBC 18148514 18148522 18156843 1) Currently only cable carrier extension cables are offered 12 Permitted cable lengths for DC 24 V BY working brakes are especially reduced. Note the following guidelines: CMPZ71. /BY: maximum 8 m CMPZ80. /BY: between 6.4 and 9 m depending on the cable cross section CMPZ100. /BY: between 4.5 and 7 m depending on the cable cross section For project planning with DC 24 V BY working brake, consult SEW EURODRIVE. Catalog CMP40 CMP112, CMPZ71 CMPZ100 359

12 Prefabricated cables Cable assignment: CMP and CMPZ, 230 V system voltage 12.11 Cable assignment: CMP and CMPZ, 230 V system voltage Motor Rated speed The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SM1 6 mm 2 to 16 mm 2 : SMB Standstill To cable Core cross current I 0 length section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP40S 3000 1.2 100 1.5 SM1 05904544 05906245 13332457 CMP40S 4500 1.2 100 1.5 SM1 05904544 05906245 13332457 CMP40S 6000 1.36 100 1.5 SM1 05904544 05906245 13332457 CMP40M 3000 1.09 100 1.5 SM1 05904544 05906245 13332457 CMP40M 4500 1.5 100 1.5 SM1 05904544 05906245 13332457 CMP40M 6000 1.91 100 1.5 SM1 05904544 05906245 13332457 CMP50S 3000 1.65 100 1.5 SM1 05904544 05906245 13332457 CMP50S 4500 2.3 100 1.5 SM1 05904544 05906245 13332457 CMP50S 6000 3.07 100 1.5 SM1 05904544 05906245 13332457 CMP50M 3000 2.85 100 1.5 SM1 05904544 05906245 13332457 CMP50M 4500 4 100 1.5 SM1 05904544 05906245 13332457 CMP50M 6000 5.25 100 1.5 SM1 05904544 05906245 13332457 CMP50L 3000 3.84 100 1.5 SM1 05904544 05906245 13332457 CMP50L 4500 5.53 100 1.5 SM1 05904544 05906245 13332457 CMP50L 6000 7.6 100 1.5 SM1 05904544 05906245 13332457 CMP63S 3000 3.61 100 1.5 SM1 05904544 05906245 13332457 CMP63S 4500 5.25 100 1.5 SM1 05904544 05906245 13332457 CMP63S 6000 6.78 100 1.5 SM1 05904544 05906245 13332457 CMP63M 3000 6.35 100 1.5 SM1 05904544 05906245 13332457 CMP63M 4500 9.78 70 1.5 SM1 05904544 05906245 13332457 CMP63M 4500 9.78 100 2.5 SM1 05904552 05906253 13332465 CMP63M 6000 12.06 55 1.5 SM1 05904544 05906245 13332457 CMP63M 6000 12.06 100 4 SM1 05904560 05904803 13332473 CMP63L 3000 8.76 75 1.5 SM1 05904544 05906245 13332457 CMP63L 3000 8.76 100 2.5 SM1 05904552 05906253 13332465 CMP63L 4500 12.01 55 1.5 SM1 05904544 05906245 13332457 CMP63L 4500 12.01 100 4 SM1 05904560 05904803 13332473 CMP.71S 3000 8.7 75 1.5 SM1 05904544 05906245 13332457 CMP.71S 3000 8.7 100 2.5 SM1 05904552 05906253 13332465 CMP.71S 4500 12.8 90 2.5 SM1 05904552 05906253 13332465 CMP.71S 4500 12.8 100 4 SM1 05904560 05904803 13332473 CMP.71S 6000 17 100 4 SM1 05904560 05904803 13332473 CMP.71M 3000 13.1 85 2.5 SM1 05904552 05906253 13332465 CMP.71M 3000 13.1 100 4 SM1 05904560 05904803 13332473 CMP.71M 4500 19.2 95 4 SM1 05904560 05904803 13332473 CMP.71L 3000 16.8 100 4 SM1 05904560 05904803 13332473 CMP.80S 3000 17.7 100 4 SM1 05904560 05904803 13332473 CMP.80S 4500 27 100 6 SMB 13350269 13350293 13350021 CMP.80S 6000 35.5 75 6 SMB 13350269 13350293 13350021 CMP.80S 6000 35.5 100 10 SMB 13350277 13350307 13350048 CMP.80M 3000 23.5 100 6 SMB 13350269 13350293 13350021 CMP.80M 4500 35 80 6 SMB 13350269 13350293 13350021 CMP.80M 4500 35 100 10 SMB 13350277 13350307 13350048 CMP.80M 6000 46.9 95 10 SMB 13350277 13350307 13350048 CMP.80M 6000 46.9 100 16 SMB 13350285 13350315 13350056 CMP.80L 3000 32.5 85 6 SMB 13350269 13350293 13350021 360 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP and CMPZ, 230 V system voltage 12 Motor Rated speed Standstill current I 0 To cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP.80L 3000 32.5 100 10 SMB 13350277 13350307 13350048 CMP.100S 3000 34.2 80 6 SMB 13350269 13350293 13350021 CMP.100S 3000 34.2 100 10 SMB 13350277 13350307 13350048 CMP.100M 3000 40 100 10 SMB 13350277 13350307 13350048 1) Currently only cable carrier extension cables are offered 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 361

12 Prefabricated cables Cable assignment: CMP /VR and CMPZ /VR, 230 V system voltage 12.12 Cable assignment: CMP /VR and CMPZ /VR, 230 V system voltage Motor Rated speed The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SM1 6 mm 2 to 16 mm 2 : SMB Standstill To cable current I 0 length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Stand-alone motor Cable carrier extension 1) CMP.71S /VR 3000 11.8 55 1.5 SM1 05904544 05906245 13332457 CMP.71S /VR 3000 11.8 100 4 SM1 05904560 05904803 13332473 CMP.71S /VR 4500 17.4 100 4 SM1 05904560 05904803 13332473 CMP.71S /VR 6000 23 80 4 SM1 05904560 05904803 13332473 CMP.71M /VR 3000 19.1 95 4 SM1 05904560 05904803 13332473 CMP.80S /VR 3000 24.5 100 6 SMB 13350269 13350293 13350021 CMP.80S /VR 4500 37 75 6 SMB 13350269 13350293 13350021 CMP.80S /VR 4500 37 100 10 SMB 13350277 13350307 13350048 CMP80S /VR 6000 48.5 95 10 SMB 13350277 13350307 13350048 CMP80S /VR 6000 48.5 100 16 SMB 13350285 13350315 13350056 CMP.80M /VR 3000 34 80 6 SMB 13350269 13350293 13350021 CMP.80M /VR 3000 34 100 10 SMB 13350277 13350307 13350048 1) Currently only cable carrier extension cables are offered 362 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP /BP /BK, 230 V system voltage 12 12.13 Cable assignment: CMP /BP /BK, 230 V system voltage Motor Rated speed The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB Standstill To cable current I 0 length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP40S /BK 3000 1.2 100 1.5 SB1 13354345 13354388 13354221 CMP40S /BK 4500 1.2 100 1.5 SB1 13354345 13354388 13354221 CMP40S /BK 6000 1.36 100 1.5 SB1 13354345 13354388 13354221 CMP40M /BK 3000 1.09 100 1.5 SB1 13354345 13354388 13354221 CMP40M /BK 4500 1.5 100 1.5 SB1 13354345 13354388 13354221 CMP40M /BK 6000 1.91 100 1.5 SB1 13354345 13354388 13354221 CMP50S /BK 3000 1.65 100 1.5 SB1 13354345 13354388 13354221 CMP50S /BK 4500 2.3 100 1.5 SB1 13354345 13354388 13354221 CMP50S /BK 6000 3.07 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK 3000 2.85 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK 4500 4 100 1.5 SB1 13354345 13354388 13354221 CMP50M /BK 6000 5.25 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK 3000 3.84 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK 4500 5.53 100 1.5 SB1 13354345 13354388 13354221 CMP50L /BK 6000 7.6 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK 3000 3.61 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK 4500 5.25 100 1.5 SB1 13354345 13354388 13354221 CMP63S /BK 6000 6.78 100 1.5 SB1 13354345 13354388 13354221 CMP63M /BK 3000 6.35 100 1.5 SB1 13354345 13354388 13354221 CMP63M /BK 4500 9.78 70 1.5 SB1 13354345 13354388 13354221 CMP63M /BK 4500 9.78 100 2.5 SB1 13354353 13354396 13354248 CMP63M /BK 6000 12.06 55 1.5 SB1 13354345 13354388 13354221 CMP63M /BK 6000 12.06 100 4 SB1 13354361 13421603 13354337 CMP63L /BK 3000 8.76 75 1.5 SB1 13354345 13354388 13354221 CMP63L /BK 3000 8.76 100 2.5 SB1 13354353 13354396 13354248 CMP63L /BK 4500 12.01 55 1.5 SB1 13354345 13354388 13354221 CMP63L /BK 4500 12.01 100 4 SB1 13354361 13421603 13354337 CMP71S /BP 3000 8.7 75 1.5 SB1 13354345 13354388 13354221 CMP71S /BP 3000 8.7 80 2.5 SB1 13354353 13354396 13354248 CMP71S /BP 4500 12.8 80 2.5 SB1 13354353 13354396 13354248 CMP71S /BP 4500 12.8 80 4 SB1 13354361 13421603 13354337 CMP71S /BP 6000 17 80 4 SB1 13354361 13421603 13354337 CMP71M /BP 3000 13.1 80 2.5 SB1 13354353 13354396 13354248 CMP71M /BP 3000 13.1 80 4 SB1 13354361 13421603 13354337 CMP71M /BP 4500 19.2 80 4 SB1 13354361 13421603 13354337 CMP71L /BP 3000 16.8 80 4 SB1 13354361 13421603 13354337 CMP80S /BP 3000 17.7 55 4 SB1 13354361 13421603 13354337 CMP80S /BP 4500 27 85 6 SBB 13350196 13350234 13350099 CMP80M /BP 3000 23.5 85 6 SBB 13350196 13350234 13350099 CMP80M /BP 4500 35 80 6 SBB 13350196 13350234 13350099 CMP80M /BP 4500 35 85 10 SBB 13350218 13350242 13350102 CMP80L /BP 3000 32.5 85 6 SBB 13350196 13350234 13350099 CMP80L /BP 3000 32.5 85 10 SBB 13350218 13350242 13350102 CMP100S /BP 3000 34.2 70 6 SBB 13350196 13350234 13350099 CMP100S /BP 3000 34.2 70 10 SBB 13350218 13350242 13350102 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 363

12 Prefabricated cables Cable assignment: CMP /BP /BK, 230 V system voltage Motor Rated speed Standstill current I 0 To cable length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP100M /BP 3000 40 70 10 SBB 13350218 13350242 13350102 1) Currently only cable carrier extension cables are offered 364 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMP /BP /VR, 230 V system voltage 12 12.14 Cable assignment: CMP /BP /VR, 230 V system voltage Motor Rated speed The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB Standstill To cable current I 0 length Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMP71S /BP /VR 3000 11.8 55 1.5 SB1 13354345 13354388 13354221 CMP71S /BP /VR 3000 11.8 80 4 SB1 13354361 13421603 13354337 CMP71S /BP /VR 4500 17.4 80 4 SB1 13354361 13421603 13354337 CMP71S /BP /VR 6000 23 80 4 SB1 13354361 13421603 13354337 CMP71M /BP /VR 3000 19.1 80 4 SB1 13354361 13421603 13354337 CMP80S /BP /VR 3000 24.5 85 6 SBB 13350196 13350234 13350099 CMP80S /BP /VR 4500 37 75 6 SBB 13350196 13350234 13350099 CMP80S /BP /VR 4500 37 85 10 SBB 13350218 13350242 13350102 CMP80M /BP /VR 3000 34 80 6 SBB 13350196 13350234 13350099 CMP80M /BP /VR 3000 34 85 10 SBB 13350218 13350242 13350102 1) Currently only cable carrier extension cables are offered 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 365

12 Prefabricated cables Cable assignment: CMPZ /BY, 230 V system voltage 12.15 Cable assignment: CMPZ /BY, 230 V system voltage Motor The following table allows for selecting power cables for CMP servo brakemotors with a system voltage of 400 V and a BY brake with 400 V, 230 V or 110 V brake voltage. An additional length for 110 V is specified in parenthesis for cases where the permitted cable length for 110 V is shorter than for 400 V/230 V. The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB To cable length Rated speed Standstill current I 0 Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMPZ71S /BY 3000 8.7 80 1.5 SB1 13354272 13354302 13354221 CMPZ71S /BY 3000 8.7 100 2.5 SB1 13354280 13354310 13354248 CMPZ71S /BY 4500 12.8 90 2.5 SB1 13354280 13354310 13354248 CMPZ71S /BY 4500 12.8 100 4 SB1 13354299 13354329 13354337 CMPZ71S /BY 6000 17 100 4 SB1 13354299 13354329 13354337 CMPZ71M /BY 3000 13.1 100 4 SB1 13354299 13354329 13354337 CMPZ71M /BY 4500 19.2 98 4 SB1 13354299 13354329 13354337 CMPZ71L /BY 3000 16.8 100 4 SB1 13354299 13354329 13354337 CMPZ80S /BY 3000 17.7 65 2.5 SB1 13354280 13354310 13354248 CMPZ80S /BY 3000 17.7 100 4 SB1 13354299 13354329 13354337 CMPZ80S /BY 4500 27 100 6 SBB 13350129 13350153 13350099 CMPZ80S /BY 6000 35.5 78 6 SBB 13350129 13350153 13350099 CMPZ80S /BY 6000 35.5 100 10 SBB 13350137 13350161 13350102 CMPZ80M /BY 3000 23.5 100 6 SBB 13350129 13350153 13350099 CMPZ80M /BY 4500 35 80 6 SBB 13350129 13350153 13350099 CMPZ80M /BY 4500 35 100 10 SBB 13350137 13350161 13350102 CMPZ80M /BY 6000 46.9 100 10 SBB 13350137 13350161 13350102 CMPZ80L /BY 3000 32.5 86 6 SBB 13350129 13350153 13350099 CMPZ80L /BY 3000 32.5 100 10 SBB 13350137 13350161 13350102 CMPZ100S /BY 3000 34.2 82 6 SBB 13350129 13350153 13350099 CMPZ100S /BY 3000 34.2 100 10 SBB 13350137 13350161 13350102 CMPZ100M /BY 3000 40 100 10 SBB 13350137 13350161 13350102 1) Currently only cable carrier extension cables are offered Permitted cable lengths for DC 24 V BY working brakes are especially reduced. Note the following guidelines: CMPZ71. /BY: maximum 8 m CMPZ80. /BY: between 6.4 and 9 m depending on the cable cross section CMPZ100. /BY: between 4.5 and 7 m depending on the cable cross section For project planning with DC 24 V BY working brake, consult SEW EURODRIVE. 366 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable assignment: CMPZ /BY /VR, 230 V system voltage 12 12.16 Cable assignment: CMPZ /BY /VR, 230 V system voltage Motor The following table allows for selecting power cables for CMP servo brakemotors with a system voltage of 400 V and a BY brake with 400 V, 230 V or 110 V brake voltage. An additional length for 110 V is specified in parenthesis for cases where the permitted cable length for 110 V is shorter than for 400 V/230 V. The part numbers refer to the smallest connector that can be used: 1.5 mm 2 to 4 mm 2 : SB1 6 mm 2 to 16 mm 2 : SBB Standstill To cable current I 0 length Rated speed Core cross section Plug connector Fixed routing Cable part no. Cable carrier installation rpm A m mm 2 Brakemotor Cable carrier extension 1) CMPZ71S /BY /VR 3000 11.8 59 1.5 SB1 13354272 13354302 13354221 CMPZ71S /BY /VR 3000 11.8 100 2.5 SB1 13354280 13354310 13354248 CMPZ71S /BY /VR 4500 17.4 100 4 SB1 13354299 13354329 13354337 CMPZ71S /BY /VR 6000 23 80 4 SB1 13354299 13354329 13354337 CMPZ71M /BY /VR 3000 19.1 98 4 SB1 13354299 13354329 13354337 CMPZ71M /BY /VR 4500 28 100 6 SBB 13350129 13350153 13350099 CMPZ71L /BY /VR 3000 27 100 6 SBB 13350129 13350153 13350099 CMPZ80S /BY /VR 3000 24.5 100 6 SBB 13350129 13350153 13350099 CMPZ80S /BY /VR 4500 37 76 6 SBB 13350129 13350153 13350099 CMPZ80S /BY /VR 4500 37 100 10 SBB 13350137 13350161 13350102 CMPZ80S /BY /VR 6000 48.5 97 10 SBB 13350137 13350161 13350102 CMPZ80S /BY /VR 6000 48.5 100 16 SBB 13350145 13350188 13350110 CMPZ80M /BY /VR 3000 34 83 6 SBB 13350129 13350153 13350099 CMPZ80M /BY /VR 3000 34 100 10 SBB 13350137 13350161 13350102 1) Currently only cable carrier extension cables are offered 12 Permitted cable lengths for DC 24 V BY working brakes are especially reduced. Note the following guidelines: CMPZ71. /BY: maximum 8 m CMPZ80. /BY: between 6.4 and 9 m depending on the cable cross section CMPZ100. /BY: between 4.5 and 7 m depending on the cable cross section For project planning with DC 24 V BY working brake, consult SEW EURODRIVE. Catalog CMP40 CMP112, CMPZ71 CMPZ100 367

12 Prefabricated cables Encoder cable assignment: Plug connector connection option /KKS 12.17 Encoder cable assignment: Plug connector connection option /KKS Encoder Connection to Cable part number MOVIDRIVE MOVIAXIS Fixed installation Cable carrier installation Fixed extension Cable carrier extension RH1M X15 01994875 01993194 01995421 01995413 AS1H, ES1H AK1H, EK1H AK0H, EK0H X13 13327429 13327437 X15 X13 13324535 13324551 01995391 01995405 12.18 Encoder cable assignment: Connection option KK Encoder Connection to Cable part number MOVIDRIVE MOVIAXIS Fixed installation Cable carrier installation RH1M X15 13356259 13356267 AK1H, EK1H AK0H X13 13356356 13356364 X15 X13 13356291 13356305 12.19 Forced cooling fan cables Cable type Cable cross section Part number Fixed installation Forced cooling fan cable 3 x 1 mm 2 01986341 Cable carrier installation 3 x 1 mm 2 0199560X 368 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Structure of prefabricated cables for CMP. servomotors 12 12.20 Structure of prefabricated cables for CMP. servomotors 12.20.1 Motor cables/brakemotor cables for CMP. servomotors [1] [2] [6] [5] X [3] 500 ±5 [4] 12 4818640779 [1] Connector: Intercontec BSTA 078 [2] SEW EURODRIVE logo printed on cable [3] Nameplate [4] Line length 10 m: Tolerance +200 mm Line length 10 m: Tolerance +2 % Permitted line length according to the technical documents [5] Prefabricated cable end for inverter Required loose parts are supplied with the cable [6] Shielding approx. 20 mm, pulled back approximately + 5 mm Prefabrication motor side The power cables on the motor side consist of an 8-pin plug connector and socket contacts. The shield is connected in the connector housing according to EMC requirements. All plug connectors seal the connector on the cable end with a lamellar seal and ensure cable relief according to EN 61884. Prefabrication on inverter end The individual cable cores of the motor and brakemotor cables are exposed and the shield is prepared for connection in the control cabinet. The cable for the inverter end still has to be prefabricated. The loose parts required are supplied with the cable in a separate bag. Catalog CMP40 CMP112, CMPZ71 CMPZ100 369

12 Prefabricated cables Structure of prefabricated cables for CMP. servomotors Loose parts The following loose parts are supplied in accordance with the core cross sections for connection to the power terminals on the inverter: Bag no. Contents 1 4 x conductor end sleeves 1.5 mm 2, insulated 4 x M6 U-shaped cable lugs 1.5 mm 2 2 4 x conductor end sleeves 2.5 mm 2, insulated 4 x M6 U-shaped cable lugs 2.5 mm 2 3 4 x conductor end sleeves 4 mm 2, insulated 4 x M6 U-shaped cable lugs 4 mm 2 12.20.2 Feedback cable [1] [2] [5] X [3] Y [4] 4818646539 [1] Connector: Intercontec ASTA [2] Printed on connector: SEW EURODRIVE [3] Nameplate [4] Line length 10 m: Tolerance +200 mm Cable length > 10 m: Tolerance +2% Permitted line length according to the technical documents. [5] D sub connector Prefabrication motor end A 12 pin EMC signal plug connector from Intercontec with socket contacts is used on the motor end for RH1M, AS1H, ES1H, AK0H, EK0H, AK1H, EK1H. The shield is connected in the connector housing according to EMC requirements. All plug connectors seal the plug on the cable end with a lamellar seal. 370 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Structure of prefabricated cables for CMP. servomotors 12 Prefabrication on inverter end A commercial D-sub EMC connector with pin contacts is used on the inverter end. A 9-pin or 15-pin connector matching the inverter is used. Hybrid cable The outer cable sheath on the motor and inverter end bears a nameplate with part number and logo of the prefabricated cable manufacturer. The ordered length and permitted tolerance are interrelated as follows: Cable length 10 m: Tolerance 200 mm. Cable length >10 m: Tolerance + 2%. INFORMATION Refer to the system manual of the inverter for determining the maximum cable length. Make sure that an EMC-compliant environment is maintained during project planning. 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 371

12 Prefabricated cables Power cables 12.21 Power cables 12.21.1 Motor cables CMP motor cables X 4818831115 CMP motor cable types Type Number of cores and cable cross section Part number Routing SM11 4 1.5 mm 2 05904544 Fixed installation SM11 4 1.5 mm 2 05906245 Cable carrier installation SM12 4 2.5 mm 2 05904552 Fixed installation SM12 4 2.5 mm 2 05906253 Cable carrier installation SM14 4 4 mm 2 05904560 Fixed installation SM14 4 4 mm 2 05904803 Cable carrier installation SMB6 4 6 mm 2 13350269 Fixed installation SMB6 4 6 mm 2 13350293 Cable carrier installation SMB10 4 10 mm 2 13350277 Fixed installation SMB10 4 10 mm 2 13350307 Cable carrier installation SMB16 4 16 mm 2 13350285 Fixed installation SMB16 4 16 mm 2 13350315 Cable carrier installation SMC16 4 16 mm 2 18148476 Fixed installation SMC16 4 16 mm 2 18148484 Cable carrier installation SMC25 4 25 mm 2 18148581 Cable carrier installation SMC35 4 35 mm 2 18148697 Cable carrier installation 372 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Power cables 12 Pin assignment of the CMP motor cable Plug connector view X W1 PE V1 U1 BSTA 078 2 SM1 3 1 4 D A C B Pin Cable core color Assigned Extra 1 (BK) Black U Bag of loose 2 (GN/YE) Green/ PE parts Yellow 3 (BK) Black W 4 (BK) Black V Plug connector view X V W - W CSTA 264 2 SMB V + U 1 PE U Pin Cable core color Assigned Extra U V W PE (BK, WH) Black with white lettering U, V, W (GN/YE) Green, yellow U V W PE Bag of loose parts 12 Plug connector view X - W 1 V DSTA 001 SMC + U 2 V U W 8837045259 Pin Cable core color Assigned Extra U V W PE (BK, WH) Black with white lettering U, V, W (GN/YE) Green, yellow U V W PE Bag of loose parts Catalog CMP40 CMP112, CMPZ71 CMPZ100 373

12 Prefabricated cables Power cables CMP motor extension cable X Y 4818839179 CMP motor extension cable types Type Number of cores and cable cross section Part number Routing SM11 4 1.5 mm 2 13332457 Cable carrier installation SM12 4 2.5 mm 2 13332465 Cable carrier installation SM14 4 4 mm 2 13332473 Cable carrier installation SMB6 4 6 mm 2 13350021 Cable carrier installation SMB10 4 10 mm 2 13350048 Cable carrier installation SMB16 4 16 mm 2 13350056 Cable carrier installation SMC16 4 16 mm 2 18156819 Cable carrier installation SMC25 4 x 25 mm 2 18156827 Cable carrier installation SMC35 4 x 35 mm 2 18156835 Cable carrier installation 374 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Power cables 12 12.21.2 Brakemotor cable for BP/BK brakes CMP brakemotor cable X 500 ±5 9007204073605387 Types of CMP brakemotor cables Type Number of cores and cable cross section Part number Routing SB11 4 1.5 mm 2 + 3 1 mm 2 13354345 Fixed installation SB11 4 1.5 mm 2 + 3 1 mm 2 13354388 Cable carrier installation SB12 4 2.5 mm 2 + 3 1 mm 2 13354353 Fixed installation SB12 4 2.5 mm 2 + 3 1 mm 2 13354396 Cable carrier installation SB14 4 4 mm 2 + 3 1 mm 2 13354361 Fixed installation SB14 4 4 mm 2 + 3 1 mm 2 13421603 Cable carrier installation SBB6 4 6 mm 2 + 3 1.5 mm 2 13350196 Fixed installation SBB6 4 6 mm 2 + 3 1.5 mm 2 13350234 Cable carrier installation SBB10 4 10 mm 2 + 3 1.5 mm 2 13350218 Fixed installation SBB10 4 10 mm 2 + 3 1.5 mm 2 13350242 Cable carrier installation SBB16 4 16 mm 2 + 3 1.5 mm 2 13350226 Fixed installation SBB16 4 16 mm 2 + 3 1.5 mm 2 13350250 Cable carrier installation 12 INFORMATION As only two signal lines are required for power cables for brakemotors with BP/BK brake, the third signal wire is cut off when prefabricating the cable. Catalog CMP40 CMP112, CMPZ71 CMPZ100 375

12 Prefabricated cables Power cables Pin assignment of CMP brakemotor cables Plug connector view X PE V1 W1 U1 BSTA 078 2 SB1 1 3 4 D C B A BK/WH BK/WH BK/WH Plug connector view X BK/WH V W CSTA 264 - W 2 SBB V BK/WH + U U 1 BK PE Pin Cable core color Assigned Extra 1 (BK/WH) Black with U 4 white lettering V 3 U, V, W W 2 (GN/YE) Green/ yellow PE A n. c. B n. c. C (BK/WH) Black with + D white lettering 1, 2, 3 Bag of loose parts Pin Cable core color Assigned Extra U V W PE (BK/WH) Black with white lettering U, V, W (GN/YE) Green/ yellow U V W PE (BK/WH) Black with + white lettering + 1, 2, 3 1 n. c. 2 n. c. Bag of loose parts 376 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Power cables 12 12.21.3 Brakemotor cables BY brake CMP brakemotor cable X 500 ±5 9007204073605387 CMP brakemotor cable types Type Number of cores and cable cross section Part number Routing SB11 4 1.5 mm 2 + 3 1 mm 2 13354272 Fixed installation SB11 4 1.5 mm 2 + 3 1 mm 2 13354302 Cable carrier installation SB12 4 2.5 mm 2 + 3 1 mm 2 13354280 Fixed installation SB12 4 2.5 mm 2 + 3 1 mm 2 13354310 Cable carrier installation SB14 4 4 mm 2 + 3 1 mm 2 13354299 Fixed installation SB14 4 4 mm 2 + 3 1 mm 2 13354329 Cable carrier installation SBB6 4 6 mm 2 + 3 1.5 mm 2 13350129 Fixed installation SBB6 4 6 mm 2 + 3 1.5 mm 2 13350153 Cable carrier installation SBB10 4 10 mm 2 + 3 1.5 mm 2 13350137 Fixed installation SBB10 4 10 mm 2 + 3 1.5 mm 2 13350161 Cable carrier installation SBB16 4 16 mm 2 + 3 1.5 mm 2 13350145 Fixed installation SBB16 4 16 mm 2 + 3 1.5 mm 2 13350188 Cable carrier installation SBC16 4 16 mm 2 + 3 1.5 mm 2 18148514 Fixed installation SBC16 4 16 mm 2 + 3 1.5 mm 2 18148522 Cable carrier installation 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 377

12 Prefabricated cables Power cables Pin assignment of CMP brakemotor cables Plug connector view X PE V1 W1 U1 BSTA 078 2 SB1 1 3 4 D C B A BK/WH BK/WH BK/WH Plug connector view X BK/WH V W CSTA 264 - W 2 SBB V BK/WH + U U 1 BK PE Plug connector view X DSTA 001 SBC BK (3) BK (1) V - + V BK (2) W U U 2 1 W Pin Cable core color Assigned Extra 1 (BK/WH) Black with U 4 white lettering U, V, W V 3 W 2 (GN/YE) Green/ Yellow PE A n. c. B (BK/WH) Black with 2 C white lettering 1 D 3 Bag of loose parts Pin Cable core color Assigned Extra U V W PE (BK/WH) Black with white lettering U, V, W (GN/YE) Green/ yellow U V W PE (BK/WH) Black with 15 + white lettering 13 1 14 2 n.c. Bag of loose parts Pin Cable core color Assigned Extra U V W PE (BK/WH) Black with white lettering U, V, W (GN/YE) Green/ yellow U V W PE (BK/WH) Black with 15 + white lettering 13 1 14 2 n.c. Bag of loose parts 378 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Power cables 12 12.21.4 Extension cables BP/BK and BY brakes CMP brakemotor extension cable X Y 4818839179 CMP brakemotor extension cable types Type Number of cores and cable cross section Part number Routing SB11 4 1.5 mm 2 + 3 1 mm 2 13354221 Cable carrier installation SB12 4 2.5 mm 2 + 3 1 mm 2 13354248 Cable carrier installation SB14 4 4 mm 2 + 3 1 mm 2 13354337 Cable carrier installation SBB6 4 6 mm 2 + 3 1.5 mm 2 13350099 Cable carrier installation SBB10 4 10 mm 2 + 3 1.5 mm 2 13350102 Cable carrier installation SBB16 4 16 mm 2 + 3 1.5 mm 2 13350110 Cable carrier installation SBC16 4 16 mm 2 + 3 1.5 mm 2 18156843 Cable carrier installation 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 379

12 Prefabricated cables Encoder cables 12.22 Encoder cables 12.22.1 Resolver Resolver cable RH1M for MOVIDRIVE MDX60B/61B X Y 4819177867 Resolver cable types RH1M for MOVIDRIVE MDX60B/61B Type Number of cores and cable cross section Part number Routing CMP 5 2 0.25 mm 2 01994875 Fixed installation CMP 5 2 0.25 mm 2 01993194 Cable carrier installation Resolver cable RH1M for MOVIAXIS MX X Y 4819185931 Resolver cable types RH1M for MOVIAXIS MX Type Number of cores and cable cross section Part number Routing CMP 5 2 0.25 mm 2 13327429 Fixed installation CMP 5 2 0.25 mm 2 13327437 Cable carrier installation 380 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Encoder cables 12 Extension cable for RH1M resolver X Y 4819192715 Extension cable types for RH1M resolvers Type Number of cores and cable cross section Part number Routing CMP 5 2 0.25 mm 2 01995421 Fixed installation CMP 5 2 0.25 mm 2 01995413 Cable carrier installation Alternative plug connector for RH1M resolver cables Signal plug connector with socket contacts (complete) 12 Type Cross sections that can be connected Part number RH1M 6 x 2 x 0.06 to 1 mm 2 01986732 Resolver cable, terminal box CMP for MOVIDRIVE X Y 4838463371 Resolver cables types, terminal box CMP for MOVIDRIVE Type Number of cores and cross sections Part number Routing CMP 5 2 0.25 mm 2 13356259 Fixed installation CMP 13356267 Cable carrier installation Catalog CMP40 CMP112, CMPZ71 CMPZ100 381

12 Prefabricated cables Encoder cables Pin assignment of resolver cables terminal box for RH1M Resolver cables, terminal box connection RH1M resolver for CMP motors Motor connection end Connection MOVIDRIVE MDX..B Terminal strip Pin no. Description Cable core color Description Pin no. Plug connector 12 11 10 9 8 7 6 5 4 3 2 1 12642818315 View X 1 R1 (reference +) 2 R2 (reference -) Pink (PK) Gray (GY) R1 (reference +) R2 (reference -) 3 S1 (cosine +) Red (RD) S1 (cosine +) 2 4 S3 (cosine -) Blue (BU) S3 (cosine -) 7 5 S2 (sine +) Yellow (YE) S2 (sine +) 1 6 S4 (sine -) Green (GN) S4 (sine -) 6 7 n.c. n.c. 4 8 n.c. 3 D sub, 9 pole 8 6 9 1 5 View Y 1) Double assignment to increase cross section 2) Double assignment to increase cross section 9 TF/KTY + (BN) Brown / (VT) violet 1) TF/ KTY + 9 10 TF/KTY - (WH) White / (BK) Black 2) TF/ KTY - 5 11 n.c. n.c. n.c. 12 n.c. n.c. n.c. Resolver cable terminal box CMP for MOVIAXIS X Y 4838463371 Resolver cable types terminal box CMP for MOVIAXIS Type Number of cores and cross sections Part number Routing CMP 5 2 0.25 mm 2 13356356 Fixed installation CMP 13356364 Cable carrier installation 382 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Encoder cables 12 RH1M resolver cables terminal box pin assignment Resolver cables, terminal box connection RH1M resolver for CMP motors Motor connection end Connection MOVIAXIS MXA Terminal strip Pin no. Description Cable core color Description Pin no. Plug connector 12 11 10 9 8 7 6 5 4 3 2 1 12642818315 View X 1 R1 (reference +) 2 R2 (reference -) Pink (PK) Gray (GY) R1 (reference +) R2 (reference -) 3 S1 (cosine +) Red (RD) S1 (cosine +) 2 4 S3 (cosine -) Blue (BU) S3 (cosine -) 10 5 S2 (sine +) Yellow (YE) S2 (sine +) 1 6 S4 (sine -) Green (GN) S4 (sine -) 9 7 n.c. n.c. 4 8 n.c. 5 D sub, 9 pole 13 6 9 1 5 View Y 12 9 TF/KTY + (BN) Brown / (VT) violet 1) TF/ KTY + 14 10 TF/KTY - (WH) White / (BK) Black 2) TF/ KTY - 6 11 n.c. n.c. n.c. 12 n.c. n.c. n.c. 1) Double assignment to increase cross section 2) Double assignment to increase cross section Catalog CMP40 CMP112, CMPZ71 CMPZ100 383

12 Prefabricated cables Encoder cables 12.22.2 Hiperface encoders Hiperface encoder cable for MOVIDRIVE B and MOVIAXIS MX X Y 4819185931 Hiperface encoder cable types for MOVIDRIVE B and MOVIAXIS MX Type Number of cores and cable cross section Part number Routing CMP 6 2 0.25 mm 2 13324535 Fixed installation CMP 6 2 0.25 mm 2 13324551 Cable carrier installation Extension cable for Hiperface encoders AK0H / EK0H / AS1H / ES1H / AK1H / EK1H X Y 4819207051 Extension cable types for Hiperface encoders K0H / EK0H / AS1H / ES1H / AK1H / EK1H Type Number of cores and cable cross section Part number Routing CMP 6 2 0.25 mm 2 01995391 Fixed installation CMP 6 2 0.25 mm 2 01995405 Cable carrier installation Alternative plug connector cables for Hiperface encoders AK0H / EK0H / AS1H / ES1H / AK1H / EK1H Signal plug connector with socket contacts (complete) Type Cross sections that can be connected Part number AK0H 6 x 2 x 0.06 to 1 mm 2 01986732 EK0H AS1H ES1H AK1H EK1H 384 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Encoder cables 12 Hiperface encoder cable, terminal box, CMP for MOVIAXIS, MOVIDRIVE X Y 4838486411 Hiperface encoder cable types, terminal box, CMP for MOVIAXIS, MOVIDRIVE Type Number of cores and cable cross section Part number Routing CMP 5 2 0.25 mm 2 13356291 Fixed installation CMP 13356305 Cable carrier installation 12 Pin assignment for Hiperface encoder cables, terminal box, AS1H / ES1H / AK1H / AK0H / EK1H Hiperface cable, terminal box connection MOVIAXIS MXA, MOVIDRIVE MDX..B with CMP motors Motor connection end Connection MOVIAXIS MXA MOVIDRIVE MDX..B Terminal strip Pin no. Description Cable core color Description Pin no. Plug connector 1 2 3 4 5 6 7 8 9 10 11 12 12642818315 View X 6 Data + Black (BK) Data + 4 D-sub, 5 Data - Violet (VT) Data - 12 15-pin 1 S1 (COS +) Red (RD) S1 (COS +) 1 2 S3 (COS -) Blue (BU) S3 (COS -) 9 3 S2 (SIN +) Yellow (YE) S2 (SIN +) 2 4 S4 (SIN -) Green (GN) S4 (SIN -) 10 7 GND Gray-pink (GYPK) / pink (PK) GND 8 8 Us Red blue (RDBU) Us 15 9 TF / TH / KTY + 10 TF / TH / KTY - Brown (BN) White (WH) TF / TH / KTY + TF / TH / KTY - 14 6 9 15 1 8 View Y Catalog CMP40 CMP112, CMPZ71 CMPZ100 385

12 Prefabricated cables Forced cooling fan cables 12.23 Forced cooling fan cables 12.23.1 Cable for motors with forced cooling fan VR [1] [3] [2] [3] X [4] 4819487627 [1] Connector: STAK 200 [2] Printed on connector: SEW-EURODRIVE [3] Nameplate [4] Line length 5 m: Tolerance +200 mm Line length 5 m: Tolerance +2% Permitted line length according to the technical documents. 12.23.2 Cable types for motors with forced cooling fan VR Type Cross section Routing Part number CMP 3 1 mm 2 (AWG 18) Fixed installation 01986341 CMP 0199560X 12.23.3 Pin assignment of cables for motors with VR forced cooling fan STAK 200 plug connector view X Connector with two socket contacts Cable carrier installation Contact Core identification Assigned Pin 1 Digit 1 24 V + Cut-off, length 2 Digit 2 0 V approx. 250 mm Connection type Conductor end sleeves 386 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Forced cooling fan cables 12 12.23.4 Alternative connector for VR forced cooling fan cable Signal plug connector with socket contacts (complete) Type Cross sections that can be connected Routing VR 3 x 1 mm 2 (AWG 18) Fixed installation / cable carrier installation Part number 01984985 12.23.5 Extension cable for motors with forced cooling fan VR [1] [3] [2] [3] [5] X [4] [1] Connector: STAS 200 [2] Printed on connector: SEW-EURODRIVE [3] Nameplate [4] Line length 5 m: Tolerance +200 mm Line length 5 m: Tolerance +2% Permitted line length according to the technical documents. [5] Socket: STAK 200 Y 4819495051 12 12.23.6 Extension cable types for motors with forced cooling fan VR Type Cross section Routing Part number CMP 3 1 mm 2 (AWG 18) Fixed installation 01995618 CMP Cable carrier installation 01995626 12.23.7 Alternative connector for cable for the VR forced cooling fan Signal plug connector with pins (complete) Type Cross sections that can be connected Part no. VR 3 x 1 mm 2 01985693 Catalog CMP40 CMP112, CMPZ71 CMPZ100 387

12 Prefabricated cables Cable specifications of power cables 12.24 Cable specifications of power cables 12.24.1 Fixed installation Motor cables Routing Cable cross sections 4 x 1.5 4 x 2.5 4 x 4 4 x 6 4 x 10 4 x 16 mm 2 mm 2 mm 2 mm 2 mm 2 mm 2 Manufacturer Manufacturer designation Operating voltage V 0 / V AC Fixed (AWG 16) (AWG 14) (AWG 12) (AWG 10) (AWG 8) (AWG 5) HELUKABEL LI9YCY V 600 / 1000 Temperature range C Fixed installation 40 to +80 Max. temperature C +80 Min. bending radius mm 45 55 65 73 85 106.5 Diameter D mm 9.0 ± 0.2 11 ± 0.2 13 ± 0.2 14.3 ± 0.3 17.0 ± 0.6 21.3 ± 0.6 Core identification BK with lettering WH + GN/YE Sheath color Orange, similar to RAL 2003 Approval(s) Capacitance conductor/ shield DESINA / VDE / UL nf/km 110 110 118 125 125 130 Capacitance core/core nf/km 70 70 75 80 80 85 Halogen-free Silicon-free CFC-free Inner insulation (conductor) Outer insulation (sheath) Flame retardant/self-extinguishing Conductor material Shielding No Yes Yes PP PVC Yes Cu Tinned Cu Weight (cable) kg/km 134 202 262 332 601 1040 388 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable specifications of power cables 12 Brakemotor cables Routing Cable cross sections 4 x 1.5 mm 2 Manufacturer Manufacturer designation Operating voltage V 0 / V AC (AWG 16) + 3 x 1 mm 2 (AWG 18) 4 x 2.5 mm 2 (AWG 14) + 3 x 1 mm 2 (AWG 18) 4 x 4 mm 2 (AWG 12) + 3 x 1 mm 2 (AWG 18) Fixed HELUKABEL LI9YCY V 600 / 1000 4 x 6 mm 2 (AWG 10) + 3 x 1.5 mm 2 (AWG 16) Temperature range C Fixed installation: 40 to +80 Max. temperature C +80 4 x 10 mm 2 (AWG 8) + 3 x 1.5 mm 2 (AWG 16) 4 x 16 mm 2 (AWG 5) + 3 x 1.5 mm 2 (AWG 16) Min. bending radius mm 60 68 75 85 100 116 Diameter D mm 11.8 ± 0.4 13.4 ± 0.4 15.0 ± 0.5 17.0 ± 0.6 20.0 ± 1.0 23.2 ± 1.0 Core identification BK with lettering WH + GN/YE Sheath color Orange similar to RAL 2003 Approval(s) DESINA / VDE / UL Capacitance conductor/shield nf/km 105 105 110 115 120 130 Capacitance core/core nf/km 60 60 70 75 78 85 Halogen-free Silicon-free CFC-free Inner insulation (conductor) Outer insulation (sheath) Flame retardant/self-extinguishing Conductor material Shielding No Yes Yes PP PVC Yes Cu Tinned Cu Weight (cable) kg/km 229 292 393 542 938 1230 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 389

12 Prefabricated cables Cable specifications of power cables 12.24.2 Cable carrier installation Motor cables Routing Cable carrier Cable cross sections 4 x 1.5 mm 2 4 x 2.5 mm 2 4 x 4.0 mm 2 4 x 6.0 mm 2 4 x 10 mm 2 4 x 16 mm 2 4 x 25 mm 2 4 x 35 mm 2 (AWG 16) (AWG 14) (AWG 12) (AWG 10) (AWG 8) (AWG 5) (AWG 3) (AWG 2) Manufacturer Nexans Helukabel Manufacturer's designation PSL(LC)C11Y-J 4 x mm 2 PSL11YC11Y-J 4 x mm 2 TOPSERV 109 Operating voltage V 0 / V AC V 600 / 1000 Temperature range C -20 to +60-50 to +80-50 to +80 Max. temperature C +90 (on conductor) Min. bending radius mm 134 140 135 155 180 225 191 215 Diameter D mm 12.8 + 0.6 / 15.7 ± 0.3 13.2 ± 0.4 15.4 ± 0.4 17.8 ± 0.5 21.8 ± 0.7 25.4 28.6 Maximum acceleration m/s 2 20 Max. velocity m/min 200 at max. travel distance of 5 m Core identification BK with lettering WH + GN/YE Sheath color Orange similar to RAL 2003 Approval(s) Capacitance conductor/ shield DESINA / VDE / UL / cruus nf/km 95 95 170 170 170 Capacitance core/core nf/km 65 65 95 95 95 Halogen-free Silicon-free CFC-free Inner insulation (conductor) Polyolefin TPM Outer insulation (sheath) Flame retardant/self-extinguishing Conductor material Yes Yes Yes TPU (PUR) Yes E-Cu blank Shielding Braided tinned Cu shield (optically covered > 85%) Weight (cable) kg/km 249 373 311 426 644 977 1523 2080 Min. bending cycles 5 million 390 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable specifications of power cables 12 Brakemotor cables Routing Cable cross sections 4 x 1.5 mm 2 Manufacturer (AWG 16) + 3 x 1 mm 2 (AWG 18) 4 x 2.5 mm 2 (AWG 14) + 3 x 1 mm 2 (AWG 18) Cable carrier 4 x 4 mm 2 (AWG 12) + 3 x 1 mm 2 (AWG 18) Nexans 4 x 6 mm 2 (AWG 10) + 3 x 1,5 mm 2 (AWG 16) 4 x 10 mm 2 (AWG 8) + 3 x 1,5 mm 2 (AWG 16) Manufacturer designation PSL(LC)C11Y-J 4x... +3A.../C PSL11YC11Y-J 4x... +3A.../C Operating voltage V 0 / V AC V 600 / 1000 Temperature range C -20 to +60 Max. temperature C +90 (conductor) 4 x 16 mm 2 (AWG 5) + 3 x 1,5 mm 2 (AWG 16) Min. bending radius mm 159 170 155 175 200 235 Diameter D mm 15.0 ± 0.9 16.5 ± 0.7 15.3 ± 0.5 17.4 ± 0.5 20.5 ± 0.5 23.3 ± 0.7 Maximum acceleration m/s 2 20 Max. velocity m/min 200 at max. travel distance of 5 m Core identification BK with lettering WH + GN/YE Sheath color Orange similar to RAL 2003 Approval(s) DESINA / VDE / UL / cruus Capacitance conductor/shield nf/km 105 105 170 170 170 170 Capacitance core/core nf/km 65 65 95 95 95 95 Halogen-free Silicon-free CFC-free Inner insulation (cable) Outer insulation (sheath) Polyolefin TPU (PUR) Flame retardant/self-extinguishing Conductor material Yes Yes Yes TPM Yes E-Cu blank Shielding Braided tinned Cu shield (optically covered > 85%) Weight (cable) kg/km 335 433 396 522 730 1053 Min. bending cycles 5 million 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 391

12 Prefabricated cables Cable specification of encoder cables 12.25 Cable specification of encoder cables 12.25.1 Fixed installation of feedback cables Accessory designation AS1H / ES1H /AK0H /EK0H / AK1H /EK1H RH1M Cable cross sections 6 x 2 x 0.25 mm 2 5 x 2 x 0.25 mm 2 Manufacturer Manufacturer designation HELUKABEL LI9YCY Operating voltage V 0 / V AC V 230 / 350 Temperature range C Fixed installation -40 to +80 Max. temperature C + 80 Min. bending radius mm 43 36.5 Diameter D mm 8.6 ± 0.2 7.3 ± 0.2 Core identification DIN 47 100 Sheath color Green, similar to RAL 6018 Approval(s) DESINA / VDE / cruus Capacitance core/shielding nf/km 110 Capacitance core/core nf/km 70 Halogen-free Silicone-free CFC-free Inner insulation (conductor) Outer insulation (sheath) Flame-retardant/self-extinguishing Conductor material Shielding No Yes Yes PP PVC No Cu blank Braided tinned Cu Weight (cable) kg/km 107 78 392 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable specification of encoder cables 12 12.25.2 Cable carrier installation of feedback cables Accessory designation AS1H / ES1H /AK0H /EK0H / AK1H /EK1H RH1M Cable cross sections 6 x 2 x 0.25 mm 2 5 x 2 x 0.25 mm 2 Manufacturer Nexans Manufacturer designation SSL18YC11Y 6 x 2 x 0.25/ SSL11YC11Y 5 x 2 x 0.25 Operating voltage V 0 / V AC V 300 Temperature range C -20 to + 60 Max. temperature C +90 (on conductor) Min. bending radius mm 100 80 Diameter D mm 9.8 ± 0.2 9.5 ± 0.2 Maximum acceleration m/s 2 20 Max. velocity m/min 200 Core identification WH/BN, GN/YE, GY/PK, BU/RD, BK/VT, GY-PK/RD-BU Sheath color Green similar to RAL 6018 Approval(s) DESINA / VDE / cruus Capacitance core/shielding nf/km 100 Capacitance core/core nf/km 55 Halogen-free Silicone-free CFC-free Inner insulation (conductor) Outer insulation (sheath) Flame-retardant/self-extinguishing Conductor material Shielding Yes Yes Yes PP TPE-U Yes E-Cu blank Braided tinned Cu WH/BN, GN/YE, GY/PK, BU/RD, BK/VT Weight kg/km 130 120 Min. bending cycles 5 million 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 393

12 Prefabricated cables Cable specifications of forced cooling fan cables 12.26 Cable specifications of forced cooling fan cables 12.26.1 Fixed installation of forced cooling fan cables Accessory designation VR Cable cross sections 3 x 1 mm 2 Manufacturer Lapp Manufacturer's designation Ölflex 110 Classic Operating voltage V 0 / V AC V 300 / 500 Temperature range C -30 to +70 Max. temperature C + 70 Min. bending radius mm 24 Diameter D mm 6.0 ± 0.3 Core identification VDE 0293 Sheath color Silver gray, RAL 7001 Approval(s) VDE Capacitance core/shielding nf/km Capacitance core/core nf/km Halogen-free No Silicone-free Yes CFC-free Yes Inner insulation (conductor) PVC Outer insulation (sheath) PVC Flame-retardant/self-extinguishing No Conductor material Cu blank Shielding Weight (cable) kg/km 65 394 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Prefabricated cables Cable specifications of forced cooling fan cables 12 12.26.2 Cable carrier installation for forced cooling fan cables Accessory designation Cable cross sections 3 x 1 mm 2 Manufacturer VR Nexans Manufacturer designation PSL 3 x 1.0 Operating voltage V 0 / V AC V 300 Temperature range C - 30 to + 70 Max. temperature C +90 (on conductor) Min. bending radius mm 45 Diameter D mm 5.7 ± 0.2 Maximum acceleration m/s 2 10 Max. velocity m/min 50 Core identification 2 x WH with digit + 1 x GN/YE Sheath color Black RAL 9005 Approval(s) VDE / UL Capacitance core/shielding nf/km Capacitance core/core nf/km Halogen-free Silicone-free CFC-free Inner insulation (conductor) Outer insulation (sheath) Flame-retardant/self-extinguishing Conductor material Yes Yes Yes TPM TPE-U Yes E-Cu blank Shielding Weight kg/km 50 Min. bending cycles 5 million 12 Catalog CMP40 CMP112, CMPZ71 CMPZ100 395

13 Appendix Cable dimensions to AWG 13 Appendix 13.1 Cable dimensions to AWG AWG stands for American Wire Gauge and refers to the size of wires. The number specifies the diameter or cross section of a wire in code. This type of cable designation is usually only used in the USA. However, the designations can also be seen in catalogs or data sheets in Europe. AWG designation 000000 (6/0) 185 00000 (5/0) 150 0000 (4/0) 120 000 (3/0) 90 00 (2/0) 70 0 (1/0) 50 1 50 2 35 3 25 4 25 5 16 6 16 7 10 8 10 9 6 10 6 11 4 12 4 13 2.5 14 2.5 15 2.5 16 1.5 16 1 18 1 19 0.75 20 0.5 21 0.5 22 0.34 23 0.25 24 0.2 Cross section in mm 2 396 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 14 Address Directory Germany Headquarters Production plant Sales Production Plant / Industrial Gear Units Bruchsal Bruchsal SEW-EURODRIVE GmbH & Co KG Ernst-Blickle-Strasse 42 76646 Bruchsal, Germany P.O. box address Postfach 3023 D-76642 Bruchsal, Germany SEW-EURODRIVE GmbH & Co KG Christian-Pähr-Str.10 76646 Bruchsal, Germany Tel. +49 7251 75-0 Fax +49 7251 75-1970 http://www.seweurodrive.com sew@sew-eurodrive.de Tel. +49 7251 75-0 Fax +49 7251 75-2970 Production plant Graben SEW-EURODRIVE GmbH & Co KG Ernst-Blickle-Strasse 1 76676 Graben-Neudorf, Germany P.O. box address Postfach 1220 76671 Graben-Neudorf, Germany Tel. +49 7251 75-0 Fax +49 7251 75-2970 Service Competence Centers Drive Technology Center Östringen Mechanical/ Mechatronic Components Electronics North East South West SEW-EURODRIVE GmbH & Co KG, Oestringen Plant Franz-Gurk-Strasse 2 76684 Oestringen, Germany SEW-EURODRIVE GmbH & Co KG Ernst-Blickle-Strasse 1 76676 Graben-Neudorf, Germany SEW-EURODRIVE GmbH & Co KG Ernst-Blickle-Strasse 42 76646 Bruchsal, Germany SEW-EURODRIVE GmbH & Co KG Alte Ricklinger Strasse 40-42 30823 Garbsen (near Hanover) SEW-EURODRIVE GmbH & Co KG Daenkritzer Weg 1 08393 Meerane (near Zwickau) SEW-EURODRIVE GmbH & Co KG Domagkstrasse 5 85551 Kirchheim (near Munich) SEW-EURODRIVE GmbH & Co KG Siemensstrasse 1 40764 Langenfeld (near Düsseldorf) Drive Service Hotline/24-hour availability Technical offices Augsburg SEW-EURODRIVE GmbH & Co KG August-Wessels-Strasse 27 86156 Augsburg, Germany Berlin Lake Constance Bremen Dortmund Dresden Erfurt Guestrow SEW-EURODRIVE GmbH & Co KG Lilienthalstrasse 3a 12529 Schoenefeld, Germany SEW-EURODRIVE GmbH & Co KG Dornierstraße 4 88677 Markdorf, Germany SEW-EURODRIVE GmbH & Co KG Bornstr.19... 22 28195 Bremen, Germany SEW-EURODRIVE GmbH & Co KG Hildastraße 8 44145 Dortmund, Germany SEW-EURODRIVE GmbH & Co KG Hauptstrasse 32 01445 Radebeul, Germany SEW-EURODRIVE GmbH & Co KG Dubliner Strasse 12 99091 Erfurt, Germany SEW-EURODRIVE GmbH & Co KG Glasewitzer Chaussee 33 B 18273 Guestrow, Germany P.O. box address Postfach 1216 18262 Güstrow, Germany Tel. +49 7253 9254-0 Fax +49 7253 9254-90 oestringen@sew eurodrive.de Tel. +49 7251 75-1710 Fax +49 7251 75-1711 sc-mitte@sew eurodrive.de Tel. +49 7251 75-1780 Fax +49 7251 75-1769 sc-elektronik@sew-eurodrive.de Tel. +49 5137 8798-30 Fax +49 5137 8798-55 sc-nord@sew-eurodrive.de Tel. +49 3764 7606-0 Fax +49 3764 7606-30 sc-ost@sew eurodrive.de Tel. +49 89 909552-10 Fax +49 89 909552-50 sc-sued@sew eurodrive.de Tel. +49 2173 8507-30 Fax +49 2173 8507-55 sc-west@sew eurodrive.de +49 800 SEWHELP +49 800 7394357 Tel. +49 821 22779-10 Fax +49 821 22779-50 tb-augsburg@sew eurodrive.de Tel. +49 306331131-30 Fax +49 306331131-36 tb-berlin@sew eurodrive.de Tel. +49 7544 96590-90 Fax +49 7544 96590-99 tb-bodensee@sew eurodrive.de Tel. +49 421 33918-10 Fax +49 421 33918-22 tb-bremen@sew eurodrive.de Tel. +49 231 229028-10 Fax +49 231 229028-20 tb-dortmund@sew eurodrive.de Tel. +49 351 26338-0 Fax +49 351 26338-38 tb-dresden@sew eurodrive.de Tel. +49 361 21709-70 Fax +49 361 21709-79 tb-erfurt@sew eurodrive.de Tel. +49 3843 8557-80 Fax +49 3843 8557-88 tb-guestrow@sew eurodrive.de 14 Catalog CMP40 CMP112, CMPZ71 CMPZ100 397

14 Address Directory Germany Hamburg SEW-EURODRIVE GmbH & Co KG Bramfelder Strasse 119 22305 Hamburg, Germany Hanover/Garbsen SEW-EURODRIVE GmbH & Co KG Alte Ricklinger Str.40-42 30823 Garbsen, Germany P.O. box address Postfach 1104 53 30804 Garbsen, Germany Heilbronn Herford Karlsruhe Kassel Koblenz Lahr Langenfeld Magdeburg Mannheim Munich Muenster Nuremberg Regensburg Rhine-Main Stuttgart Ulm Drive Center Wuerzburg Zwickau / Meerane SEW-EURODRIVE GmbH & Co KG Zeppelinstrasse 7 74357 Boennigheim, Germany SEW-EURODRIVE GmbH & Co KG Göbenstraße 3 7 32052 Herford SEW-EURODRIVE GmbH & Co KG Ettlinger Weg 2 76467 Bietigheim, Germany P.O. box address Postfach 43 76463 Bietigheim, Germany SEW-EURODRIVE GmbH & Co KG Lange Strasse 14 34253 Lohfelden, Germany SEW-EURODRIVE GmbH & Co KG Bahnstrasse 17a 56743 Mendig, Germany SEWEURODRIVE GmbH & Co KG Europastrasse 3/1 77933 Lahr/Schwarzwald, Germany SEW-EURODRIVE GmbH & Co KG Siemensstrasse 1 40764 Langenfeld, Germany SEW-EURODRIVE GmbH & Co KG Breiteweg 53 39179 Barleben, Germany SEW-EURODRIVE GmbH & Co KG Besselstrasse 26 68219 Mannheim, Germany SEW-EURODRIVE GmbH & Co KG Domagkstrasse 5 85551 Kirchheim, Germany SEW-EURODRIVE GmbH & Co KG Hafenplatz 4 48155 Muenster, Germany SEW-EURODRIVE GmbH & Co KG Plattenaeckerweg 6 90455 Nuremberg, Germany SEW-EURODRIVE GmbH & Co KG Im Gewerbepark A15 93059 Regensburg, Germany SEW-EURODRIVE GmbH & Co KG Niederstedter Weg 5 61348 Bad Homburg, Germany SEW-EURODRIVE GmbH & Co KG Friedrich-List-Strasse 46 70771 Leinfelden-Echterdingen, Germany SEWEURODRIVE GmbH & Co KG Dieselstrasse 14 89160 Dornstadt, Germany SEW-EURODRIVE GmbH & Co KG Nuernbergerstrasse 118 97076 Wuerzburg-Lengfeld, Germany SEW-EURODRIVE GmbH & Co KG Dänkritzer Weg 1 08393 Meerane, Germany Tel. +49 40 298109-60 Fax +49 40 298109-70 tb-hamburg@sew eurodrive.de Tel. +49 5137 8798-10 Fax +49 5137 8798-50 tb-hannover@sew eurodrive.de Tel. +49 7143 8738-0 Fax +49 7143 8738-25 tb-heilbronn@sew eurodrive.de Tel. +49 5221 9141-0 Fax +49 5221 9141-20 tb-herford@sew eurodrive.de Tel. +49 7245 9190-10 Fax +49 7245 9190-20 tb-karlsruhe@sew eurodrive.de Tel. +49 561 95144-80 Fax +49 561 95144-90 tb-kassel@sew eurodrive.de Tel. +49 2652 9713-30 Fax +49 2652 9713-40 tb-koblenz@sew eurodrive.de Tel. +49 7821 90999-60 Fax +49 7821 90999-79 tb-lahr@sew eurodrive.de Tel. +49 2173 8507-10 Fax +49 2173 8507-50 tb-langenfeld@sew eurodrive.de Tel. +49 39203 7577-1 Fax +49 39203 7577-9 tb-magdeburg@sew eurodrive.de Tel. +49 621 71683-10 Fax +49 621 71683-22 tb-mannheim@sew eurodrive.de Tel. +49 89 90955-110 Fax +49 89 90955-150 tb-muenchen@sew eurodrive.de Tel. +49 251 41475-11 Fax +49 251 41475-50 tb-muenster@sew eurodrive.de Tel. +49 911 98884-50 Fax +49 911 98884-60 tb-nuernberg@sew eurodrive.de Tel. +49 941 46668-68 Fax +49 941 46668-66 tb-regensburg@sew eurodrive.de Tel. +49 6172 9617-0 Fax +49 6172 9617-50 tb-rheinmain@sew eurodrive.de Tel. +49 711 16072-0 Fax +49 711 16072-72 tb-stuttgart@sew eurodrive.de Tel. +49 7348 9885-0 Fax +49 7348 9885-90 tb-ulm@sew eurodrive.de Tel. +49 931 27886-60 Fax +49 931 27886-66 tb-wuerzburg@sew eurodrive.de Tel. +49 3764 7606-0 Fax +49 3764 7606-20 tb-zwickau@sew eurodrive.de 398 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 France Production plant Sales Service Haguenau SEW-USOCOME 48-54 route de Soufflenheim B. P. 20185 67506 Haguenau Cedex, France Production plant Forbach SEW-USOCOME Zone industrielle Technopôle Forbach Sud B. P. 30269 57604 Forbach Cedex, France Assembly plant Sales Service Bordeaux Lyon Nantes Paris SEW-USOCOME Parc d'activités de Magellan 62 avenue de Magellan - B. P. 182 33607 Pessac Cedex, France SEW-USOCOME Parc d'affaires Roosevelt Rue Jacques Tati 69120 Vaulx en Velin, France SEW-USOCOME Parc d activités de la forêt 4 rue des Fontenelles 44140 Le Bignon, France SEW-USOCOME Zone industrielle 2 rue Denis Papin 77390 Verneuil I'Etang, France Technical offices Alsace SEW-USOCOME 1 rue Auguste Gasser 68360 Soultz, France Lower Normandy Burgundy Brittany Centre/Poitou Aquitaine/Charente Auvergne/Limousin Champagne-Ardenne Franche-Comté Île-de-France East/Aisne Île-de-France North/Picardy Île-de-France South SEW-USOCOME Parc d'activités de Magellan 62 avenue de Magellan - B.P.182 33607 Pessac Cedex, France SEW-USOCOME Farges 19600 Chasteaux, France SEW-USOCOME 5 rue de la Limare 14250 Brouay, France SEW-USOCOME 10 rue de la poste 71350 Saint Loup Géanges, France SEW-USOCOME Parc d activités de la forêt 4 rue des Fontenelles 44140 Le Bignon, France SEW-USOCOME Parc d activités de la forêt 4 rue des Fontenelles 44140 Le Bignon, France SEW-USOCOME 25 bis rue Victor Hugo Appartement 7 10120 Saint André les Vergers, France SEW-USOCOME 24 avenue Charles Boby 70000 Quincey, France SEW-USOCOME 20 rue Félix Faure 02100 Saint Quentin, France SEW-USOCOME 25bis rue Kléber 92300 Levallois Perret, France SEW-USOCOME 6 chemin des bergers Lieu-dit Marchais 91410 Roinville sous Dourdan, France Tel. +33 3 88 73 67 00 Fax +33 3 88 73 66 00 http://www.usocome.com sew@usocome.com Tel. +33 3 87 29 38 00 Tel. +33 5 57 26 39 00 Fax +33 5 57 26 39 09 Tel. +33 4 72 15 37 00 Fax +33 4 72 15 37 15 Tel. +33 2 40 78 42 00 Fax +33 2 40 78 42 20 Tel. +33 1 64 42 40 80 Fax +33 1 64 42 40 88 Tel. +33 3 89 74 51 62 Fax +33 3 89 76 58 71 Tel. +33 5 57 26 39 08 Fax +33 5 57 26 39 09 Tel. +33 5 55 20 12 10 Fax +33 5 55 20 12 11 Tel. +33 2 31 37 92 86 Fax +33 2 31 74 68 15 Tel. +33 3 85 49 92 18 Fax +33 3 85 49 92 19 Tel. +33 2 40 78 42 04 Fax +33 2 40 78 42 20 Tel. +33 2 40 78 42 11 Fax +33 2 40 78 42 20 Tel. +33 3 25 79 63 24 Fax +33 3 25 79 63 25 Tel. +33 3 81 60 20 47 Fax +33 3 81 87 75 93 Tel. +33 3 23 62 81 24 Fax +33 3 23 62 81 44 Tel. +33 1 41 05 92 74 Fax +33 1 41 05 92 75 Tel. +33 1 60 81 10 56 Fax +33 1 60 81 10 57 14 Catalog CMP40 CMP112, CMPZ71 CMPZ100 399

14 Address Directory France Lothringen/Northern Alsace Midi-Pyrénées/ Roussillon Nord-Pas-de-Calais Paris/Île-de- France West Pays de la Loire Provence-Alpes- Côte d Azur SEW-USOCOME 1 rue de la forêt 54250 Champigneulles, France SEW-USOCOME 179 route de Grazac 31190 Caujac, France SEW-USOCOME 209, route d Hesdigneul 62360 Hesdin l Abbé, France SEW-USOCOME 42 avenue Jean Jaurès 78580 Maule, France SEW-USOCOME Parc d activités de la forêt 4 rue des Fontenelles 44140 Le Bignon, France SEW-USOCOME Le Clos Montolivet 9 impasse Bounin Bât. A 13012 Marseille, France Rhône-Alpes East SEW-USOCOME Montée de la Garenne 26750 Génissieux, France Rhône-Alpes North Rhône-Alpes West SEW-USOCOME Parc d'affaires Roosevelt Rue Jacques Tati 69120 Vaulx en Velin, France SEW-USOCOME Parc d'affaires Roosevelt Rue Jacques Tati 69120 Vaulx en Velin, France Tel. +33 3 83 96 28 04 Fax +33 3 83 96 28 07 Tel. +33 5 61 08 15 85 Fax +33 5 61 08 16 44 Tel. +33 3 21 10 86 86 Fax +33 3 21 10 86 87 Tel. +33 1 30 90 89 86 Fax +33 1 30 90 93 15 Tel. +33 2 40 78 42 03 Fax +33 2 40 78 42 20 Tel. +33 4 91 18 00 11 Fax +33 4 91 18 00 12 Tel. +33 4 75 05 65 95 Fax +33 4 75 05 65 96 Tel. +33 4 72 15 37 03 Fax +33 4 72 15 37 15 Tel. +33 4 72 15 37 04 Fax +33 4 72 15 37 15 Algeria Sales Algiers REDUCOM Sarl 16, rue des Frères Zaghnoune Bellevue 16200 El Harrach Alger Tel. +213 21 8214-91 Fax +213 21 8222-84 info@reducom-dz.com http://www.reducom-dz.com Argentina Assembly plant Sales Buenos Aires Córdoba Santa Fe SEW EURODRIVE ARGENTINA S.A. Ruta Panamericana Km 37.5, Lote 35 (B1619IEA) Centro Industrial Garín Prov. de Buenos Aires SEW EURODRIVE ARGENTINA S.A. Ruta Nacional 19, Manzana 97, Lote 5 (X5125) Malvinas Argentinas Prov. de Córdoba SEW EURODRIVE ARGENTINA S.A. Ruta Prov. 21 Km 7, Lote 41 Parque Industrial Alvear (2126) Gral. Alvear Prov. de Santa Fe Tel. +54 3327 4572-84 Fax +54 3327 4572-21 sewar@sew eurodrive.com.ar http://www.sew-eurodrive.com.ar Tel. +54 351-490-0010 sewcor@sew-eurodrive.com.ar http://www.sew-eurodrive.com.ar Tel. +54 341-317-7277 sewsfe@sew-eurodrive.com.ar http://www.sew-eurodrive.com.ar Service Mendoza SEW EURODRIVE ARGENTINA S.A. Tel. +54 261-430-0060 sewmen@sew-eurodrive.com.ar http://www.sew-eurodrive.com.ar Technical offices Tucumán SEW EURODRIVE ARGENTINA S.A. Balcarce 609 (T4000IAM) S.M. de Tucumán Prov. de Tucumán Bahía Blanca Comahue SEW EURODRIVE ARGENTINA S.A. O'Higgins 95, 1er Piso A (B8000IVA) Bahía Blanca Prov. de Buenos Aires SEW EURODRIVE ARGENTINA S.A. Puerto Rico 1885 (R8324IOE) Cipolletti Prov. de Río Negro Tel. +54 381-400-4569 sewtuc@sew-eurodrive.com.ar http://www.sew-eurodrive.com.ar Tel. +54 291-451-7345 sewbb@sew-eurodrive.com.ar http://www.sew-eurodrive.com.ar Tel. +54 299-478-1290 sewcomahue@sew-eurodrive.com.ar http://www.sew-eurodrive.com.ar 400 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 Argentina Mining Mendoza SEW EURODRIVE ARGENTINA S.A. Tel. +54 261-430-0060 mineria@sew-eurodrive.com.ar http://www.sew-eurodrive.com.ar Australia Assembly plants Sales Service Sales Service Melbourne Sydney Adelaide Brisbane Perth SEW EURODRIVE PTY. LTD. 27 Beverage Drive Tullamarine, Victoria 3043, Australia SEW EURODRIVE PTY. LTD. 9, Sleigh Place, Wetherill Park New South Wales, 2164, Australia SEW EURODRIVE PTY. LTD. 9C Park Way Mawson Lakes, SA 5095, Australia SEW EURODRIVE PTY.LTD. 1 /34 Collinsvale St Rocklea, Queensland, 4106, Australia SEW EURODRIVE PTY. LTD. 10 Colin Jamieson Drive Welshpool, WA 6106, Australia Sales Townsville SEW EURODRIVE PTY. LTD. 12 Leyland Street Garbutt, QLD 4814, Australia Austria Assembly plant Sales Service Vienna SEW EURODRIVE Ges.m.b.H. Richard-Strauss-Strasse 24 1230 Wien, Austria Technical offices Linz SEW EURODRIVE Ges.m.b.H. Reuchlinstr. 6/3 4020 Linz, Austria Bangladesh Graz Dornbirn SEW EURODRIVE Ges.m.b.H. Grabenstraße 231 8045 Graz, Austria SEW EURODRIVE Ges.m.b.H. Lustenauerstraße 27/1 6850 Dornbirn, Austria Sales Bangladesh SEW EURODRIVE INDIA PRIVATE LIMITED 345 DIT Road East Rampura Dhaka-1219, Bangladesh Belarus Sales Minsk SEW EURODRIVE BY RybalkoStr. 26 220033 Minsk, Belarus Tel. +61 3 9933-1000 Fax +61 3 9933-1003 http://www.sew-eurodrive.com.au enquires@sew eurodrive.com.au Tel. +61 2 9725-9900 Fax +61 2 9725-9905 enquires@sew eurodrive.com.au Tel. +61 8 8161 4000 Fax +61 8 8161 4002 enquires@sew eurodrive.com.au Tel. +61 7 3276 5100 Fax +61 7 3276 5102 enquires@sew eurodrive.com.au Tel. +61 8 9251-4900 Fax +61 8 9251-4903 enquires@sew eurodrive.com.au Tel. +61 7 4779 4333 Fax +61 7 4779 5333 enquires@sew eurodrive.com.au Tel. +43 1 617 55 00-0 Fax +43 1 617 55 00-30 http://www.sew-eurodrive.at sew@sew eurodrive.at Tel. +43 732 655 109-0 Fax +43 732 655 109-20 tb-linz@sew eurodrive.at Tel. +43 316 685 756-0 Fax +43 316 685 755 tb-graz@sew eurodrive.at Tel. +43 5572 3725 99-0 Fax +43 5572 3725 99-20 tb-dornbirn@sew eurodrive.at Mobile +88 01729 097309 salesdhaka@seweurodrivebangladesh.com Tel. +375 17 298 47 56 / 298 47 58 Fax +375 17 298 47 54 http://www.sew.by sales@sew.by 14 Belgium Assembly plant Sales Service Service Competence Centers Brazil Production plant Sales Service Brussels Industrial gear units São Paulo SEW EURODRIVE n.v./s.a. Researchpark Haasrode 1060 Evenementenlaan 7 BE-3001 Leuven SEW EURODRIVE n.v./s.a. Rue de Parc Industriel, 31 6900 Marche-en-Famenne, Belgium SEW EURODRIVE Brasil Ltda. Avenida Amâncio Gaiolli, 152 - Rodovia Presidente Dutra Km 208 Guarulhos - 07251-250 - SP, Brazil SAT - SEW ATENDE - 0800 7700496 Tel. +32 16 386-311 Fax +32 16 386-336 http://www.sew-eurodrive.be info@sew eurodrive.be Tel. +32 84 219-878 Fax +32 84 219-879 http://www.sew-eurodrive.be service-wallonie@sew eurodrive.be Tel. +55 11 2489-9133 Fax +55 11 2480-3328 http://www.sew-eurodrive.com.br sew@sew.com.br Catalog CMP40 CMP112, CMPZ71 CMPZ100 401

14 Address Directory Brazil Assembly plants Sales Service Rio Claro Joinville Indaiatuba SEW EURODRIVE Brasil Ltda. Rodovia Washington Luiz, Km 172 Condomínio Industrial Conpark Caixa Postal: 327 13501-600 Rio Claro / SP SEW EURODRIVE Brasil Ltda. Rua Dona Francisca, 12.346 Pirabeiraba 89239-270 Joinville / SC SEW EURODRIVE Brasil Ltda. Estrada Municipal Jose Rubim, 205 Rodovia Santos Dumont Km 49 13347-510 Indaiatuba / SP Tel. +55 19 3522-3100 Fax +55 19 3524-6653 montadora.rc@sew.com.br Tel. +55 47 3027-6886 Fax +55 47 3027-6888 filial.sc@sew.com.br Tel. +55 19 3835-8000 sew@sew.com.br Bulgaria Sales Sofia BEVER-DRIVE GmbH Bogdanovetz Str.1 1606 Sofia, Bulgaria Tel. +359 2 9151160 Fax +359 2 9151166 bever@bever.bg Cameroon Sales Douala, Cameroon Electro-Services Rue Drouot Akwa B.P. 2024 Douala, Cameroon Tel. +237 33 431137 Fax +237 33 431137 electrojemba@yahoo.fr Canada Assembly plants Sales Service Chile Assembly plant Sales Service Toronto Vancouver Montreal SEW-EURODRIVE CO. OF CANADA LTD. 210 Walker Drive Bramalea, ON L6T 3W1 SEW-EURODRIVE CO. OF CANADA LTD. Tilbury Industrial Park 7188 Honeyman Street Delta, BC V4G 1G1 SEW-EURODRIVE CO. OF CANADA LTD. 2555 Rue Leger Lasalle, PQ H8N 2V9 Please contact us for more addresses of service centers in Canada. Santiago de Chile SEW EURODRIVE CHILE LTDA. Las Encinas 1295 Parque Industrial Valle Grande LAMPA RCH-Santiago de Chile P.O. box address Casilla 23 Correo Quilicura - Santiago - Chile Tel. +1 905 791-1553 Fax +1 905 791-2999 http://www.sew-eurodrive.ca l.watson@sew eurodrive.ca Tel. +1 604 946-5535 Fax +1 604 946-2513 b.wake@sew eurodrive.ca Tel. +1 514 367-1124 Fax +1 514 367-3677 a.peluso@sew eurodrive.ca Tel. +56 2 75770-00 Fax +56 2 75770-01 http://www.sew-eurodrive.cl ventas@sew eurodrive.cl China Production plant Assembly plant Sales Service Assembly plant Sales Service Tianjin Suzhou Guangzhou Shenyang SEW EURODRIVE (Tianjin) Co., Ltd. No. 46, 7th Avenue, TEDA Tianjin 300457 SEW EURODRIVE (Suzhou) Co., Ltd. 333, Suhong Middle Road Suzhou Industrial Park Jiangsu Province, 215021 SEW EURODRIVE (Guangzhou) Co., Ltd. No. 9, JunDa Road East Section of GETDD Guangzhou 510530, China SEW EURODRIVE (Shenyang) Co., Ltd. 10A-2, 6th Road Shenyang Economic Technological Development Area Shenyang, 110141, China Tel. +86 22 25322612 Fax +86 22 25323273 info@sew eurodrive.cn http://www.sew-eurodrive.cn Tel. +86 51262581781 Fax +86 512 62581783 suzhou@sew eurodrive.cn Tel. +86 20 82267890 Fax +86 20 82267922 guangzhou@sew eurodrive.cn Tel. +86 24 25382538 Fax +86 24 25382580 shenyang@sew eurodrive.cn 402 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 China Wuhan Xi'An SEW EURODRIVE (Wuhan) Co., Ltd. 10A-2, 6th Road No. 59, the 4th Quanli Road, WEDA 430056 Wuhan, China SEW EURODRIVE (Xi'An) Co., Ltd. No. 12 Jinye 2nd Road Xi'An High-Technology Industrial Development Zone Xi'An 710065 Tel. +86 27 84478388 Fax +86 27 84478389 wuhan@sew eurodrive.cn Tel. +86 29 68686262 Fax +86 29 68686311 xian@sew eurodrive.cn Colombia Assembly plant Sales Service Bogota SEW EURODRIVE COLOMBIA LTDA. Calle 22 No. 132-60 Bodega 6, Manzana B Santafé de Bogotá, Colombia Tel. +57 1 54750-50 Fax +57 1 54750-44 http://www.sew-eurodrive.com.co sew@sew-eurodrive.com.co Côte d'ivoire Sales Abidjan SICA Tel. +225 21 25 79 44 Société Industrielle & Commerciale pour l'afrique Fax +225 21 25 88 28 165, Boulevard de Marseille sicamot@aviso.ci 26 BP 1173 Abidjan 26 Croatia Sales Service Zagreb KOMPEKS d. o. o. Zeleni dol 10 10 000 Zagreb, Croatia Tel. +385 1 4613-158 Fax +385 1 4613-158 kompeks@inet.hr 14 Czech Republic Sales Assembly plant Service Assembly plant Service Hostivice SEW EURODRIVE CZ S.R.O. Floriánova 2459 253 01 Hostivice Drive Service Hotline/24-hour avail- HOTLINE: +420 800 739 739 (800 SEW SEW) ability Plzeň SEW EURODRIVE CZ S.R.O. Areal KRPA a.s. Zahradni 173/2 326 00 Plzeň Technical offices Brno SEW EURODRIVE CZ S.R.O. Křenová 52 60200 Brno Hradec Králové Ostrava Klatovy SEW EURODRIVE CZ S.R.O. Čechova 498 50202 Hradec Králové SEW EURODRIVE CZ S.R.O. Studentská 6202/17 708 00 Ostrava-Poruba SEW EURODRIVE CZ S.R.O. Vídeňská 841 33901 Klatovy Service Horní Moštěnice SEW EURODRIVE CZ S.R.O. Nám.Dr.M.Tyrše 14/64 751 17 Horní Moštěnice Tel. +420 255 709 601 Fax +420 235 350 613 http://www.sew-eurodrive.cz sew@sew eurodrive.cz Service: Tel. +420 255 709 632 Fax +420 235 358 218 servis@sew eurodrive.cz Tel. +420 378 775 320 Fax +420 377 970 710 sew@sew eurodrive.cz Tel. +420 543 254 174 Fax +420 543 256 845 radek.chmela@sew-eurodrive.cz Tel. +420 495 510 141 Fax +420 495 521 313 miroslav.moravec@sew-eurodrive.cz Tel. +420 597 329 044 david.kenkus@sew-eurodrive.cz Tel. +420 376 331 634 Fax +420 376 331 634 viktor.kubernat@sew-eurodrive.cz Tel. +420 581 224 374 Fax +420 581 224 374 servis@sew eurodrive.cz Denmark Assembly plant Sales Service Egypt Sales Service Copenhagen Cairo SEW EURODRIVE A/S Geminivej 28-30 2670 Greve, Denmark Copam Egypt for Engineering & Agencies 33 EI Hegaz ST, Heliopolis, Cairo, Egypt Tel. +45 43 9585-00 Fax +45 43 9585-09 http://www.sew-eurodrive.dk sew@sew eurodrive.dk Tel. +20 2 22566-299 +1 23143088 Fax +20 2 22594-757 http://www.copam-egypt.com/ copam@datum.com.eg Catalog CMP40 CMP112, CMPZ71 CMPZ100 403

14 Address Directory Estonia Sales Tallinn ALAS-KUUL AS Reti tee 4 EE-75301 Peetri küla, Rae vald, Harjumaa, Estonia Tel. +372 6593230 Fax +372 6593231 veiko.soots@alas-kuul.ee Finland Assembly plant Sales Service Hollola SEW EURODRIVE OY Vesimäentie 4 15860 Hollola 2, Finland Service Hollola SEW EURODRIVE OY Keskikankaantie 21 FIN-15860 Hollola Technical offices Helsinki SEW EURODRIVE OY Luutnantintie 5 00410 Helsinki, Finland Production plant Assembly plant Gabon Vaasa Kuopio Karkkila SEW EURODRIVE OY Asemakatu 7 65100 Vaasa, Finland SEW EURODRIVE OY Viestikatu 3 70600 Kuopio, Finland SEW Industrial Gears Oy Valurinkatu 6, PL 8 FI-03600 Karkkila, 03601 Karkkila Sales Libreville, Gabon ESG Electro Services Gabun Feu Rouge Lalala 1889 Libreville Gabon Greece Sales Athens Christ. Boznos & Son S.A. 12, K. Mavromichali Street P.O. Box 80136 GR-18545 Piraeus Technical office Thessaloniki Christ. Boznos & Son S.A. Asklipiou 26 562 24 Evosmos, Thessaloniki, Greece Tel. +358 201 589-300 Fax +358 3 780-6211 http://www.sew-eurodrive.fi sew@sew.fi Tel. +358 201 589-300 Fax +358 3 780-6211 http://www.sew-eurodrive.fi sew@sew.fi Tel. +358 201 589-300 sew@sew.fi Tel. +358 201 589-300 sew@sew.fi Tel. +358 201 589-300 sew@sew.fi Tel. +358 201 589-300 Fax +358 201 589-310 sew@sew.fi http://www.sew-eurodrive.fi Tel. +241 741059 Fax +241 741059 esg_services@yahoo.fr Tel. +30 2 1042 251-34 Fax +30 2 1042 251-59 http://www.boznos.gr info@boznos.gr Tel. +30 2 310 7054-00 Fax +30 2 310 7055-15 info@boznos.gr Great Britain Assembly plant Sales Service Service Competence Centers Normanton SEW EURODRIVE Ltd. DeVilliers Way Trident Park Normanton West Yorkshire WF6 1GX Tel. +44 1924 893-855 Fax +44 1924 893-702 http://www.sew-eurodrive.co.uk info@sew eurodrive.co.uk Drive Service Hotline/24-hour availability Tel. +44 1924 896911 Southern England SEW EURODRIVE Ltd. Unit 41 Easter Park Benyon Road Silchester Reading Berkshire RG7 2PQ Technical offices Midlands SEW EURODRIVE Ltd. 5 Sugar Brook Court Aston Road Bromsgrove Worcs. B60 3EX Tel. +44 1189 701-699 Fax +44 1189 701-021 Tel. +44 1527 877-319 Fax +44 1527 575-245 404 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 Great Britain Scotland SEW EURODRIVE Ltd. No 37 Enterprise House Springkerse Business Park Stirling FK7 7UF Tel. +44 17 8647-8730 Fax +44 17 8645-0223 Hong Kong Assembly plant Sales Service Hong Kong SEW EURODRIVE LTD. Unit No. 801-806, 8th Floor Hong Leong Industrial Complex No. 4, Wang Kwong Road Kowloon, Hong Kong Tel. +852 36902200 Fax +852 36902211 contact@sew eurodrive.hk Hungary Sales Service Budapest SEW EURODRIVE Kft. 1037 Budapest, Hungary Kunigunda u. 18 Tel. +36 1 437 06-58 Fax +36 1 437 06-50 http://www.sew-eurodrive.hu office@sew-eurodrive.hu India Company office Assembly plant Sales Service Assembly plant Sales Service Vadodara Chennai SEW EURODRIVE India Private Limited Plot No. 4, GIDC POR Ramangamdi Vadodara - 391 243, India Gujarat SEW EURODRIVE India Private Limited Plot No. K3/1, Sipcot Industrial Park Phase II Mambakkam Village Sriperumbudur - 602105 Kancheepuram Dist, Tamil Nadu Technical offices Ahmedabad SEW EURODRIVE India Private Limited 306, Shaan office complex, Behind Sakar-IV, Ellisebridge, Ashram Road Ahmedabad Gujarat, India Tel. +91 265 3045200, +91 265 2831086 Fax +91 265 3045300, +91 265 2831087 http://www.seweurodriveindia.com salesvadodara@seweurodriveindia.com Tel. +91 44 37188888 Fax +91 44 37188811 saleschennai@seweurodriveindia.com Tel. +91 79 40072067/68 Fax +91 79 40072069 salesahmedabad@seweurodriveindia.com Aurangabad SEW EURODRIVE INDIA PRIVATE LIMITED Tel. +91 86000 12333 salesaurangabad@seweurodriveindia.com Bangalore Bangladesh Bellary Chandigarh Chennai Kochi SEW EURODRIVE India Private Limited Tel. +91 80 22266565 Sy.no:41-P3, Peenya1, Phase 1A, Peenya Village, Yeswanthapura Hobli, Bangalore North Ta- salesbangalore@seweurodriveindia.com Fax +91 80 22266569 luk, Bangalore Dist, Karnataka SEW EURODRIVE India Private Limited Tel. +91 80 28522662 / 28522663 # C-104, 3rd Block, KSSIDC Complex, Electronic salesbangalore@seweurodriveindia.com City. Bangalore 560100, Karnataka SEW EURODRIVE INDIA PRIVATE LIMITED Genetic Udayanchal, House-96 (6th Floor), Road-23/A, Block-B, Banani, Dhaka-1213, Bangladesh SEW EURODRIVE India Private Limited Door no-56/279 Ward No-16, Sindhigi compound, Near Raghavendra talkies, Bellary-583101 Karnataka SEW EURODRIVE India Private Limited # 72, Type- 4, Power Colony, Chandigarh - Rupnagar Highway Rupnagar- 140001, Punjab SEW EURODRIVE India Private Limited 2nd Floor, Josmans Complex, No. 5, McNichols Road, Chetpet Chennai - 600031 - Tamil Nadu, India SEW EURODRIVE India Private Limited CF7-(2), Block No 1, Vasanth Nagar, Opposite Jawahar Lal Nehru Stadium, Palarivattom Cochin 682025 Mobile +88 01729 097309 salesdhaka@seweurodrivebangladesh.com Tel. +91 77609 88668 salesbellary@seweurodriveindia.com Tel. +91 81462 67606 saleschandigarh@seweurodriveindia.com Tel. +91 44 42849813 Fax +91 44 42849816 saleschennai@seweurodriveindia.com Tel. +91 98951 30375 salescochin@seweurodriveindia.com 14 Catalog CMP40 CMP112, CMPZ71 CMPZ100 405

14 Address Directory India Coimbatore Cuttack Gandhidham Hyderabad Jamshedpur SEW EURODRIVE INDIA PRIVATE LIMITED 687/2, SRI SAKTHIVEL TOWERS (NEAR DEEPAM HOSPITAL) TRICHY ROAD, RAMANATHAPURAM COIMBATORE - 641 045.Tamilnadu, India SEW EURODRIVE India Private Limited Plot No. 1764, Nuasahi, Nayapalli Bhubaneswar-12 Orissa SEW EURODRIVE India Private Limited TCX-S-28, FF, Ward 12/A, Gandhidham - Kutch - 370201 SEW EURODRIVE India Private Limited 408, 4th Floor, Meridian Place Green Park Road Amerpeet Hyderabad - 500016 - Andhra Pradesh, India SEW EURODRIVE India Private Limited Flat no.: S1 " Kashi Kunj",h. No. 60, New Rani Kudar Road No - 3 P.o. + P.s. - Kadma Jamshedpur - Pin - 831005 Jharkhand Tel. +91 422 2322420 Fax +91 422 2323988 salescoimbatore@seweurodriveindia.com Tel. +91 9937446333 salescuttack@seweurodriveindia.com Tel. +91 81282 36850 salesgandhidham@seweurodriveindia.com Tel. +91 40 23414698 Fax +91 40 23413884 saleshyderabad@seweurodriveindia.com Tel. +91 9934123671 salesjamshedpur@seweurodriveindia.com Kolhapur SEW EURODRIVE India Private Limited Tel. +91 86000 20846 saleskolhapur@seweurodriveindia.com Kolkata Lucknow Mumbai Nagpur Nashik New Delhi Pune Raipur SEW EURODRIVE India Private Limited 2nd floor, Room No. 35 Chowringhee Court 55, Chowringhee Road Kolkata - 700 071 - West Bengal, India SEW EURODRIVE India Private Limited 69, Shiv Vihar Colony Vikas Nagar-5 Lucknow 226022 - Uttar Pradesh SEW EURODRIVE India Private Limited 312 A, 3rd Floor, Acme Plaza, J.B. Nagar, Andheri Kurla Road, Andheri (E) Mumbai - 400059 - Maharashtra, India SEW EURODRIVE India Private Limited Plot No 49, New Kailash Nager, Samta colony, Nagpur-440027 SEW EURODRIVE India Private Limited 107, "YOG" Bunglow, Mahatama Nagar, Trimbak Road, Nashik, Maharashtra 422 007 SEW EURODRIVE India Private Limited 1008, 10th Floor, 12th Level "Westend Mall" Tower Plot, District Centre Adjacent Hotel Hilton Janak Puri, New Delhi 110058 SEW EURODRIVE India Private Limited Jai Tulajabhavani Complex. Office No: 15 First Floor, Opp. Century Enka Company, MIDC Bhosari, Pune 411 026 SEW EURODRIVE India Private Limited LUNAWAT PRISM 4th Floor, S.No. 148 Opposite Wanaz Company, Besides Mega Mart At Neena Co-Operative Housing Society, Paud Road, Pune 411038 - Maharashtra, India SEW EURODRIVE India Private Limited A-42, Ashoka Millenium Complex, Ring Road-1, Raipur 492 001 - Chhattisgarh, India Tel. +91 33 22827457 Fax +91 33 22894204 saleskolkata@seweurodriveindia.com Tel. +91 9793627333 saleslucknow@seweurodriveindia.com Tel. +91 22 28348440 Fax +91 22 28217858 salesmumbai@seweurodriveindia.com Tel. +91 95610 89525 salesnagpur@seweurodriveindia.com Tel. +91 9665752978 salesnashik@seweurodriveindia.com Tel. +91 11 25544111 Fax +91 11 25544113 salesdelhi@seweurodriveindia.com Tel. +91 20-65118890 / 91 Fax +91 20 25380721 salespune@seweurodriveindia.com Tel. +91 20 25380730/735 Fax +91 20 25380721 salespune@seweurodriveindia.com praveen.hosur@seweurodriveindia.com Tel. +91 771 4090765 Fax +91 771 4090765 salesraipur@seweurodriveindia.com 406 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 India Ranchi Tiruchirappalli Vadodara Vijayawada SEW EURODRIVE India Private Limited Flat No.: A - 101, Krishna Shree Apartment, Anantpur, P.O. Doranda Ranchi 834002 SEW EURODRIVE India Private Limited A-106,Trichy Towers, Chandrasekarapuram, Salai Road, Trichy 620018. SEW EURODRIVE India Private Limited Unit No. 301, Savorite Bldg, Plot No. 143, Vinayak Society, off old Padra Road, Vadodara - 390 007. Gujarat SEW EURODRIVE India Private Limited Door No:40-5/3-10A, Syam Nagar, NGO's Colony, Tikkle Road, Vijayawada-520010 Tel. +91 8294630772 salesranchi@seweurodriveindia.com Mobile +91 95009 88081 salestrichy@seweurodriveindia.com Tel. +91 265 2325258 Fax +91 265 2325259 salesvadodara@seweurodriveindia.com Tel. +91 99895 01748 Fax +91 8662475157 Mobile +91 9989501748 salesvijayawada@seweurodriveindia.com Indonesia Sales Jakarta PT. Cahaya Sukses Abadi Tel. +62 21 65310599 Komplek Rukan Puri Mutiara Blok A no 99, Sunter csajkt@cbn.net.id Fax +62 21 65310600 Jakarta 14350, Indonesia Medan Surabaya PT. Agrindo Putra Lestari Jl.Prof.DR.Latumenten no27/a Jakarta 11330 PT. Serumpun Indah Lestari Pulau Solor no. 8, Kawasan Industri Medan II Medan 20252 PT. TRIAGRI JAYA ABADI Jl. Sukosemolo No. 63, Galaxi Bumi Permai G6 No. 11 Surabaya 60122 CV. Multi Mas Jl. Raden Saleh 43A Kav. 18 Surabaya 60174 Tel. +62 21 63855588 Fax +62 21 63853789 aplindo@indosat.net.id Tel. +62 61 687 1221 Fax +62 61 6871429 / +62 61 6871458 / +62 61 30008041 sil@serumpunindah.com serumpunindah@yahoo.com Tel. +62 31 5990128 Fax +62 31 5962666 triagri@indosat.net.id Tel. +62 31 5458589 / +62 31 5317224 Fax +62 31 5317220 / +62 31 5994629 sianhwa@sby.centrin.net.id 14 Ireland Sales Service Dublin Alperton Engineering Ltd. 48 Moyle Road Dublin Industrial Estate Glasnevin, Dublin 11, Ireland Tel. +353 1 830-6277 Fax +353 1 830-6458 info@alperton.ie http://www.alperton.ie Iceland Sales Reykjavik VARMA & VELAVERK EHF Dalshrauni 5 IS-220 Hafnarjördur Israel Sales Tel Aviv Liraz Handasa Ltd. Ahofer Str 34B / 228 58858 Holon, Israel Italy Assembly plant Sales Service Solaro SEW EURODRIVE di R. Blickle & Co.s.a.s. Via Bernini,14 I-20020 Solaro (Milano), Italy Technical offices Bologna SEW EURODRIVE di R. Blickle & Co.s.a.s. Via della Grafica, 47 40064 Ozzano dell'emilia (Bo), Italy Tel. +354 585 1070 Fax +354 585 1071 varmaverk@varmaverk.is http://www.varmaverk.is Tel. +972 3 5599511 Fax +972 3 5599512 http://www.liraz-handasa.co.il office@liraz-handasa.co.il Tel. +39 02 96 9801 Fax +39 02 96 980 999 http://www.sew-eurodrive.it sewit@sew eurodrive.it Tel. +39 051 65-23-801 Fax +39 02 96 980 499 Catalog CMP40 CMP112, CMPZ71 CMPZ100 407

14 Address Directory Italy Caserta Milan Pescara Turin Verona SEW EURODRIVE di R. Blickle & Co.s.a.s. Viale Carlo III Km. 23,300 81020 S. Nicola la Strada (Caserta), Italy SEW EURODRIVE di R. Blickle & Co.s.a.s. Via Bernini,14 I-20020 Solaro (Milano), Italy SEW EURODRIVE di R. Blickle & Co.s.a.s. Viale Europa,132 I-65010 Villa Raspa di Spoltore (PE) SEW EURODRIVE di R. Blickle & Co.s.a.s. Filiale Torino c.so Unione Sovietica 612/15 - int. C 10135 Torino, Italy SEW EURODRIVE di R. Blickle & Co.s.a.s. Via Antonio Meucci 5, I-37042 - Caldiero ( VR ) Tel. +39 0823 219011 Fax +39 02 96 980 599 Tel. +39 02 96 980229 Fax +39 02 96 980 999 Tel. +39 085 41-59-427 Fax +39 02 96 980 699 Tel. +39 011 3473780 Fax +39 02 96 980 799 Tel. +39 045 89-239-11 Fax +39 02 96 980 814 Japan Assembly plant Sales Service Iwata SEW EURODRIVE JAPAN CO., LTD 250-1, Shimoman-no, Iwata Shizuoka 438-0818 Technical offices Fukuoka SEW EURODRIVE JAPAN CO., LTD. C-go, 5th-floor, Yakuin-Hiruzu-Bldg. 1-5-11, Yakuin, Chuo-ku Fukuoka, 810-0022, Japan Kazakhstan Osaka Tokyo SEW EURODRIVE JAPAN CO., LTD. Higobashi Shimizu Bldg. 10th floor 1-3-7 Tosabori, Nishi-ku Osaka, 550-0001, Japan SEW EURODRIVE JAPAN CO., LTD. Omarimon Yusen Bldg. 13th floor 3-23-5 Nishinbashi, Minato-ku Tokyo 105-0003, Japan Sales Almaty ТОО "СЕВ-ЕВРОДРАЙВ" пр.райымбека, 348 050061 г. Алматы Республика Казахстан Kenya Sales Nairobi Barico Maintenances Ltd Kamutaga Place Commercial Street Industrial Area P.O.BOX 52217-00200 Nairobi Latvia Sales Riga SIA Alas-Kuul Katlakalna 11C 1073 Riga, Latvia Lebanon Sales Lebanon Beirut Gabriel Acar & Fils sarl B. P. 80484 Bourj Hammoud, Beirut, Lebanon Sales Jordan / Kuwait / Saudi Arabia / Syria Beirut After Sales Service Middle East Drives S.A.L. (offshore) Sin El Fil. B. P. 55-378 Beirut After Sales Service Tel. +81 538 373811 Fax +81 538 373855 http://www.sew-eurodrive.co.jp sewjapan@sew eurodrive.co.jp Tel. +81 92 713-6955 Fax +81 92 713-6860 sewkyushu@jasmine.ocn.ne.jp Tel. +81 6 6444--8330 Fax +81 6 6444--8338 sewosaka@crocus.ocn.ne.jp Tel. +81 3 3239-0469 Fax +81 3 3239-0943 sewtokyo@basil.ocn.ne.jp Тел. +7 (727) 334 1880 Факс +7 (727) 334 1881 http://www.sew-eurodrive.kz sew@sew eurodrive.kz Tel. +254 20 6537094/5 Fax +254 20 6537096 info@barico.co.ke Tel. +371 6 7139253 Fax +371 6 7139386 http://www.alas-kuul.com info@alas-kuul.com Tel. +961 1 510 532 Fax +961 1 494 971 ssacar@inco.com.lb service@medrives.com Tel. +961 1 494 786 Fax +961 1 494 971 info@medrives.com http://www.medrives.com service@medrives.com 408 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 Lithuania Sales Alytus UAB Irseva Statybininku 106C LT-63431 Alytus Tel. +370 315 79204 Fax +370 315 56175 irmantas@irseva.lt http://www.sew-eurodrive.lt Luxembourg Assembly plant Sales Service Brussels SEW EURODRIVE n.v./s.a. Researchpark Haasrode 1060 Evenementenlaan 7 BE-3001 Leuven Tel. +32 16 386-311 Fax +32 16 386-336 http://www.sew-eurodrive.lu info@sew eurodrive.be Madagascar Sales Antananarivo Ocean Trade BP21bis. Andraharo Antananarivo. 101 Madagascar Malaysia Assembly plant Sales Service Johor SEW EURODRIVE SDN BHD No. 95, Jalan Seroja 39, Taman Johor Jaya 81000 Johor Bahru, Johor West Malaysia Technical offices Kuala Lumpur SEW EURODRIVE Sdn. Bhd. No. 2, Jalan Anggerik Mokara 31/46 Kota Kemuning Seksyen 31 40460 Shah Alam Selangor Darul Ehsan Kuching Penang SEW EURODRIVE Sdn. Bhd. Lot 268, Section 9 KTLD Lorong 9, Jalan Satok 93400 Kuching, Sarawak East Malaysia SEW EURODRIVE Sdn. Bhd. No. 38, Jalan Bawal Kimsar Garden 13700 Prai, Penang Tel. +261 20 2330303 Fax +261 20 2330330 oceantrabp@moov.mg Tel. +60 7 3549409 Fax +60 7 3541404 sales@sew eurodrive.com.my Tel. +60 3 51229633 Fax +60 3 51229622 sewsa@sew-eurodrive.com.my Tel. +60 82 232380 Fax +60 82 242380 Tel. +60 4 3999349 Fax +60 4 3999348 sewpg@sew-eurodrive.com.my 14 Morocco Sales Service Mohammedia SEW EURODRIVE SARL 2 bis, Rue Al Jahid 28810 Mohammedia Tel. +212 523 32 27 80/81 Fax +212 523 32 27 89 sew@sew eurodrive.ma http://www.sew-eurodrive.ma Mauritania Sales Zouérat AFRICOM - SARL En Face Marché Dumez P.B. 88 Zouérate Macedonia Sales Skopje Boznos DOOEL Dime Anicin 2A/7A 1000 Skopje Mexico Assembly plant Sales Service Mongolia Quéretaro SEW EURODRIVE MEXICO SA DE CV SEM-981118-M93 Tequisquiapan No. 102 Parque Industrial Quéretaro C.P. 76220 Quéretaro, Mexico Sales Ulan Bator SEW-EURODRIVE Representative Office Mongolia Olympic street 8, 2nd floor Juulchin corp bldg., Sukhbaatar district, Ulaanbaatar 14253 Tel. +222 45 44 50 19 Fax +222 45 44 03 14 contact@africom-sarl.com Tel. +389 23256553 Fax +389 23256554 http://www.boznos.mk Tel. +52 442 1030-300 Fax +52 442 1030-301 http://www.sew-eurodrive.com.mx scmexico@seweurodrive.com.mx Tel. +976-70009997 Fax +976-70009997 http://www.sew-eurodrive.mn sew@sew-eurodrive.mn Catalog CMP40 CMP112, CMPZ71 CMPZ100 409

14 Address Directory Namibia Sales Swakopmund DB Mining & Industrial Services Einstein Street Strauss Industrial Park Unit1 Swakopmund Tel. +264 64 462 738 Fax +264 64 462 734 sales@dbmining.in.na New Zealand Assembly plants Sales Service Technical offices Auckland Christchurch, New Zealand SEW EURODRIVE NEW ZEALAND LTD. P.O. Box 58-428 82 Greenmount Drive East Tamaki Auckland, New Zealand SEW EURODRIVE NEW ZEALAND LTD. 10 Settlers Crescent, Ferrymead Christchurch, New Zealand Palmerston North SEW EURODRIVE NEW ZEALAND LTD. C/-Grant Shearman, RD 5, Aronui Road Palmerston North Tel. +64 9 2745627 Fax +64 9 2740165 http://www.sew-eurodrive.co.nz sales@sew eurodrive.co.nz Tel. +64 3 384-6251 Fax +64 3 384-6455 sales@sew eurodrive.co.nz Tel. +64 6 355-2165 Fax +64 6 355-2316 sales@sew eurodrive.co.nz Netherlands Assembly plant Sales Service Rotterdam SEW EURODRIVE B.V. Industrieweg 175 3044 AS Rotterdam, Netherlands Postbus 10085 3004 AB Rotterdam, Netherlands Tel. +31 10 4463-700 Fax +31 10 4155-552 Service: 0800-SEWHELP http://www.sew-eurodrive.nl info@sew eurodrive.nl Nigeria Sales Lagos EISNL Engineering Solutions and Drives Ltd Plot 9, Block A, Ikeja Industrial Estate (Ogba Scheme) Adeniyi Jones St. End Off ACME Road, Ogba, Ikeja, Lagos Nigeria Tel. +234 1 217 4332 team.sew@eisnl.com http://www.eisnl.com Norway Assembly plant Sales Service Moss SEW EURODRIVE A/S Solgaard skog 71 1599 Moss, Norway Tel. +47 69 24 10 20 Fax +47 69 24 10 40 http://www.sew-eurodrive.no sew@sew eurodrive.no Pakistan Sales Karatschi Industrial Power Drives Al-Fatah Chamber A/3, 1st Floor Central Commercial Area, Sultan Ahmed Shah Road, Block 7/8, Karachi Tel. +92 21 452 9369 Fax +92-21-454 7365 seweurodrive@cyber.net.pk Paraguay Sales Fernando de la Mora SEW-EURODRIVE PARAGUAY S.R.L De la Victoria 112, Esquina nueva Asunción Departamento Central Fernando de la Mora, Barrio Bernardino Tel. +595 991 519695 Fax +595 21 3285539 sew-py@sew-eurodrive.com.py Peru Assembly plant Sales Service Lima SEW DEL PERU MOTORES REDUCTORES S.A.C. Los Calderos, 120-124 Urbanizacion Industrial Vulcano, ATE, Lima, Peru Tel. +51 1 3495280 Fax +51 1 3493002 http://www.sew-eurodrive.com.pe sewperu@sew eurodrive.com.pe Philippines Sales Luzon Totaltech Corporation 5081-B C&L Mansion Filmore Ave. Cor. Fahrenheit St. 1235 Makati City All Areas P.T. Cerna Corporation 4137 Ponte St., Brgy. Santa Cruz, Makati City 1205 Tel. +63 2 551-9265 / +63 2 551-9271 / +63 2 551-9378 Fax +63 2 551-9273 totaltech89@gmail.com Tel. +63 2 519 6214 Fax +63 2 890 2802 mech_drive_sys@ptcerna.com 410 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 Poland Assembly plant Sales Service Łódź SEW EURODRIVE Polska Sp.z.o.o. ul. Techniczna 5 92-518 Łódź, Poland Service Tel. +48 42 6765332 / 42 6765343 Fax +48 42 6765346 Technical office Tychy SEW EURODRIVE Polska Sp.z.o.o. ul. Strzelecka 66 PL-43-109 Tychy Portugal Assembly plant Sales Service Service Competence Centers Bydgoszcz Gdansk Poznan Radom Coimbra Lisbon SEW EURODRIVE Polska Sp.z.o.o. ul. Fordońska 246 PL-85-959 Bydgoszcz SEW EURODRIVE Polska Sp.z.o.o. ul. Galaktyczna 30A PL-80-299 Gdańsk SEW EURODRIVE Polska Sp.z.o.o. ul. Romana Maya 1 61-371 Poznań, Poland SEW EURODRIVE Polska Sp.z.o.o. ul. Słowackiego 84 26-600 Radom, Poland SEW EURODRIVE, LDA. Apartado 15 3050-901 Mealhada, Portugal SEW EURODRIVE, LDA. Núcleo Empresarial I de São Julião do Tojal Rua de Entremuros, 54 Fracção I 2660-533 São Julião do Tojal, Portugal Technical office Porto SEW EURODRIVE, LDA. Av. 25 de Abril, 68 4440-502 Valongo, Portugal Tel. +48 42 676 53 00 Fax +48 42 676 53 49 http://www.sew-eurodrive.pl sew@sew eurodrive.pl Linia serwisowa 24 hour hotline Tel. +48 602 739 739 (+48 602 SEW SEW) serwis@sew eurodrive.pl Tel. +48 32 32 32 610 Fax +48 32 32 32 648 Tel. +48 52 3606590 Fax +48 52 3606591 Tel. +48 58 762 70 00 Fax +48 58 762 70 09 Tel. +48 61 6465500 Fax +48 61 6465519 Tel. +48 48 365 40 50 Fax +48 48 365 40 52 Tel. +351 231 20 9670 Fax +351 231 20 3685 http://www.sew-eurodrive.pt infosew@sew eurodrive.pt Tel. +351 21 958-0198 Fax +351 21 958-0245 esc.lisboa@sew eurodrive.pt Tel. +351 229 350 383 Fax +351 229 350 384 Tel. +351 9 32559110 esc.porto@sew eurodrive.pt 14 Romania Sales Service Bucharest Sialco Trading SRL str. Brazilia nr. 36 011783 Bucuresti, Romania Tel. +40 21 230-1328 Fax +40 21 230-7170 sialco@sialco.ro Russia Assembly plant Sales Service St. Petersburg ZAO SEW EURODRIVE P.O. Box 36 RUS-195220 St. Petersburg Technical office Ekaterinburg ZAO SEW EURODRIVE Kominterna Str. 16 Office 614 620078 Ekaterinburg, Russia Irkutsk Moscow Novosibirsk Perm ZAO SEW EURODRIVE 5-Armii Str., 31 664011 Irkutsk, Russia ZAO SEW EURODRIVE Malaja Semjonowskaja Str. д. 9, корпус 2 107023 Moscow ZAO SEW EURODRIVE pr. K Marksa 30 630087 Novosibirsk, Russia ZAO SEW EURODRIVE Stakhanovskaya str., 45 Office 512 RUS-614066 Perm Tel. +7 812 3332522 +7 812 5357142 Fax +7 812 3332523 http://www.sew-eurodrive.ru sew@sew eurodrive.ru Tel. +7 343 310 3977 Fax +7 343 310 3978 eso@sew eurodrive.ru Tel. +7 3952 25 5880 Fax +7 3952 25 5881 iso@sew eurodrive.ru Tel. +7 495 9337090 Fax +7 495 9337094 mso@sew eurodrive.ru Tel. +7 383 3350200 Fax +7 383 3462544 nso@sew eurodrive.ru Tel. +7 342 2219494 Fax +7 342 2219444 pso@sew-eurodrive.ru Catalog CMP40 CMP112, CMPZ71 CMPZ100 411

14 Address Directory Russia Togliatti ZAO SEW EURODRIVE Sportivnaya Str. 4B, office 2 Samarskaya obl. 445057 Togliatti, Russia Tel. +7 8482 710529 Fax +7 8482 810590 Senegal Sales Dakar SENEMECA Mécanique Générale Km 8, Route de Rufisque B.P. 3251, Dakar Serbia Sales Belgrade DIPAR d.o.o. Ustanicka 128a PC Košum, IV sprat SRB-11000 Beograd, Serbia Tel. +221 338 494 770 Fax +221 338 494 771 senemeca@sentoo.sn http://www.senemeca.com Tel. +381 11 347 3244 / +381 11 288 0393 Fax +381 11 347 1337 office@dipar.rs Singapore Assembly plant Sales Service Singapore SEW EURODRIVE PTE. LTD. No 9, Tuas Drive 2 Jurong Industrial Estate Singapore 638644 Tel. +65 68621701 Fax +65 68612827 http://www.sew-eurodrive.com.sg sewsingapore@sew eurodrive.com Slovakia Sales Bratislava SEW EURODRIVE SK s.r.o. Rybničná 40 831 06 Bratislava, Slovakia Žilina Banska Bystrica Košice SEW EURODRIVE SK s.r.o. Industry Park - PChZ ulica M.R.Štefánika 71 010 01 Žilina, Slovakia SEW EURODRIVE SK s.r.o. Rudlovská cesta 85 974 11 Banská Bystrica, Slovakia SEW EURODRIVE SK s.r.o. Slovenská ulica 26 040 01 Košice, Slovakia Tel. +421 2 33595 202 Fax +421 2 33595 200 sew@sew eurodrive.sk http://www.sew-eurodrive.sk Tel. +421 41 700 2513 Fax +421 41 700 2514 sew@sew eurodrive.sk Tel. +421 48 414 6564 Fax +421 48 414 6566 sew@sew eurodrive.sk Tel. +421 55 671 2245 Fax +421 55 671 2254 sew@sew eurodrive.sk Slovenia Sales Service Celje Pakman - Pogonska Tehnika d.o.o. UI. XIV. divizije 14 3000 Celje, Slovenia Tel. +386 3 490 83-20 Fax +386 3 490 83-21 pakman@siol.net Spain Assembly plant Sales Service Bilbao SEW EURODRIVE ESPAÑA, S.L. Parque Tecnológico, Edificio, 302 48170 Zamudio (Vizcaya), Spain Technical offices Barcelona Delegación Barcelona Avda. Francesc Macià, 60 Planta 16, porta 1 Eix Macià "Torre Milenium" 08208 Sabadell (Barcelona), Spain Sri Lanka Madrid Sevilla Valencia Delegación Madrid Gran Via. 48-2 A-D 28220 Majadahonda (Madrid), Spain MEB Pólogono Calonge, C/A Nave 2 - C E-41.077 Sevilla, Spain MEB Músico Andreu i Piqueres, 4 E-46.900 Torrente (Valencia) Sales Colombo SM International (Pte) Ltd 254, Galle Raod Colombo 4, Sri Lanka Tel. +34 94 43184-70 Fax +34 94 43184-71 http://www.sew-eurodrive.es sew.spain@sew eurodrive.es Tel. +34 93 7162200 Fax +34 93 7233007 Tel. +34 91 6342250 Fax +34 91 6340899 Tel. +34 954 356 361 Fax +34 954 356 274 mebsa.sevilla@mebsa.com Tel. +34 961 565 493 Fax +34 961 566 688 mebsa.valencia@mebsa.com Tel. +94 1 2584887 Fax +94 1 2582981 412 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 South Africa Assembly plants Sales Service Johannesburg Cape Town Durban, South Africa Nelspruit SEW EURODRIVE (PROPRIETARY) LIMITED Eurodrive House Cnr. Adcock Ingram and Aerodrome Roads Aeroton Ext. 2 Johannesburg 2013, South Africa P.O.Box 90004 Bertsham 2013, South Africa SEW EURODRIVE (PROPRIETARY) LIMITED Rainbow Park Cnr. Racecourse & Omuramba Road Montague Gardens Cape Town, South Africa P.O. Box 36556 Chempet 7442 Cape Town, South Africa SEW EURODRIVE (PROPRIETARY) LIMITED 48 Prospecton Road Isipingo Durban, South Africa P.O. Box 10433, Ashwood 3605, South Africa SEW EURODRIVE (PTY) LTD. 7 Christie Crescent Vintonia P.O. Box 1942 Nelspruit 1200 Technical offices Port Elizabeth SEW EURODRIVE PTY LTD. 8 Ruan Access Park Old Cape Road Greenbushes 6000 Port Elizabeth South Korea Assembly plant Sales Service Ansan Busan SEW EURODRIVE KOREA CO., LTD. B 601-4, Banweol Industrial Estate #1048-4, Shingil-Dong, Danwon-Gu, Ansan-City, Kyunggi-Do Zip 425-839 SEW EURODRIVE KOREA Co., Ltd. No. 1720-11, Songjeong - dong Gangseo-ku Busan 618-270, Korea Technical offices Daegu SEW EURODRIVE KOREA Co., Ltd. No.1108 Sungan officetel 87-36, Duryu 2-dong, Dalseo-ku Daegu 704-712 Daejeon Gwangju Seoul SEW EURODRIVE KOREA Co., Ltd. No. 1502, Hongin officetel 536-9, Bongmyung-dong, Yusung-ku Daejeon 305-301 SEW EURODRIVE KOREA Co., Ltd. 4fl., Dae-Myeong B/D 96-16 Unam-dong, Buk-ku Kwangju 500-170 SEW EURODRIVE KOREA Co., Ltd. No.504 Sunkyung officetel 106-4 Kuro 6-dong, Kuro-ku Seoul 152-054, Korea Tel. +27 11 248-7000 Fax +27 11 494-3104 http://www.sew.co.za info@sew.co.za Tel. +27 21 552-9820 Fax +27 21 552-9830 Telex 576 062 bgriffiths@sew.co.za Tel. +27 31 902 3815 Fax +27 31 902 3826 cdejager@sew.co.za Tel. +27 13 752-8007 Fax +27 13 752-8008 robermeyer@sew.co.za Tel. +27 41 3722246 Fax +27 41 3722247 dtait@sew.co.za Tel. +82 31 492-8051 Fax +82 31 492-8056 http://www.sew-korea.co.kr master.korea@sew eurodrive.com Tel. +82 51 832-0204 Fax +82 51 832-0230 master@sew-korea.co.kr Tel. +82 53 650-7111 Fax +82 53 650-7112 Tel. +82 42 828-6461 Fax +82 42 828-6463 Tel. +82 62 511-9172 Fax +82 62 511-9174 Tel. +82 2 862-8051 Fax +82 2 862-8199 14 Swaziland Sales Manzini C G Trading Co. (Pty) Ltd PO Box 2960 Manzini M200 Sweden Assembly plant Sales Service Jönköping SEW-EURODRIVE AB Gnejsvägen 6-8 55303 Jönköping, Sweden Box 3100 S-55003 Jönköping Tel. +268 2 518 6343 Fax +268 2 518 5033 engineering@cgtrading.co.sz Tel. +46 36 3442 00 Fax +46 36 3442 80 http://www.sew-eurodrive.se jonkoping@sew.se Catalog CMP40 CMP112, CMPZ71 CMPZ100 413

14 Address Directory Sweden Sales Göteborg SEW-EURODRIVE AB Gustaf Werners gata 8 42132 Västra Frölunda, Sweden Switzerland Assembly plant Sales Service Stockholm Malmö Skellefteå Basel SEW-EURODRIVE AB Björkholmsvägen 10 14146 Huddinge, Sweden SEW-EURODRIVE AB Borrgatan 5 21124 Malmö, Sweden SEW-EURODRIVE AB Trädgårdsgatan 8 93131 Skellefteå, Sweden Alfred lmhof A.G. Jurastrasse 10 CH-4142 Münchenstein bei Basel Technical offices Romandy André Gerber Es Perreyres 1436 Chamblon, Switzerland Taiwan (R.O.C.) Bern / Solothurn Central Switzerland, Aargau Zurich, Tessin Rudolf Bühler Muntersweg 5 2540 Grenchen, Switzerland Armin Pfister Stierenweid 4950 Huttwill, BE, Switzerland Gian-Michele Muletta Fischerstrasse 61 8132 Egg bei Zürich, Switzerland Lake Constance Markus Künzle and Eastern Switzerland Eichweg 4 9403 Goldach, Switzerland Sales Nan Tou Ting Shou Trading Co., Ltd. No. 55 Kung Yeh N. Road Industrial District Nan Tou 540 Tanzania Taipei Ting Shou Trading Co., Ltd. 6F-3, No. 267, Sec. 2 Tung Hwa South Road, Taipei, Taiwan Sales Dar es Salaam SEW-EURODRIVE PTY LIMITED TANZANIA Plot 52, Regent Estate PO Box 106274 Dar Es Salaam Thailand Assembly plant Sales Service Chonburi SEW EURODRIVE (Thailand) Ltd. 700/456, Moo.7, Donhuaroh Muang Chonburi 20000, Thailand Technical offices Bangkok SEW EURODRIVE (Thailand) Ltd. 6th floor, TPS Building 1023, Phattanakarn Road Suanluang Bangkok,10250 Hat Yai SEW EURODRIVE (Thailand) Ltd. Hadyai Country Home Condominium 59/101 Soi.17/1 Rachas-Utid Road. Hadyai, Songkhla 90110, Thailand Tel. +46 31 70968 80 Fax +46 31 70968 93 goteborg@sew.se Tel. +46 8 44986 80 Fax +46 8 44986 93 stockholm@sew.se Tel. +46 40 68064 80 Fax +46 40 68064 93 malmo@sew.se Tel. +46 910 7153 80 Fax +46 910 7153 93 skelleftea@sew.se Tel. +41 61 417 1717 Fax +41 61 417 1700 http://www.imhof-sew.ch info@imhof-sew.ch Tel. +41 24 445 3850 Fax +41 24 445 4887 Tel. +41 32 652 2339 Fax +41 32 652 2331 Tel. +41 62 962 54 55 Fax +41 62 962 54 56 Tel. +41 44 994 81 15 Fax +41 44 994 81 16 Tel. +41 71 845 2808 Fax +41 71 845 2809 Tel. +886 49 255353 Fax +886 49 257878 Tel. +886 2 27383535 Fax +886 2 27368268 Telex 27 245 sewtwn@ms63.hinet.net Tel. +255 0 22 277 5780 Fax +255 0 22 277 5788 uroos@sew.co.tz Tel. +66 38 454281 Fax +66 38 454288 sewthailand@sew eurodrive.com Tel. +66 2 7178149 Fax +66 2 7178152 sewthailand@sew eurodrive.com Tel. +66 74 359441 Fax +66 74 359442 sewthailand@sew eurodrive.com 414 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Address Directory 14 Thailand Khon Kaen SEW EURODRIVE (Thailand) Ltd. 4th Floor, Kaow-U-HA MOTOR Bldg, 359/2, Mitraphab Road. Muang District Khonkaen 40000, Thailand Tel. +66 43 225745 Fax +66 43 324871 sew-thailand@sew eurodrive.com Tunisia Sales Tunis T. M.S. Technic Marketing Service Zone Industrielle Mghira 2 Lot No. 39 2082 Fouchana Turkey Assembly plant Sales Service Kocaeli-Gebze SEW-EURODRİVE Sistemleri San. Ve TIC. Ltd. Sti Gebze Organize Sanayi Böl. 400 Sok No. 401 41480 Gebze Kocaeli Technical offices Adana SEW-EURODRİVE Cevat Yurdakul Cad.No:52 Akdoğan İş Merkezi K:5 D.18 Seyhan / Adana Ukraine Assembly plant Sales Service Ankara Bursa Istanbul Izmir Dnipropetrowsk SEW-EURODRİVE 1368.Cadde Eminel İşmerkezi No: 18/68 İvogsan / Ankara SEW-EURODRİVE Üçevler Mah. Bayraktepe Sok. Akay İş Merkezi Kat:3 No: 7/6 Nilüfer / Bursa SEW-EURODRİVE Tekstilkent Ticaret Merkezi B-13 Blok No:70 Esenler / İstanbul SEW-EURODRİVE 1203/11 Sok. No. 4/614 Kara Hasan Atlı İş Merkezi Kat :6 Yenişehir / İzmir ООО «СЕВ-Евродрайв» ул.рабочая, 23-B, офис 409 49008 Днепропетровск Sales Kiev ООО «СЕВ-Евродрайв» ул.с.олейника, 21 02068 Киев Donetsk Ivano-Frankivsk ООО «СЕВ-Евродрайв» ул.25-летия РККА, 1-B, оф. 805 83000 Донецк ООО «СЕВ-Евродрайв» ул.независимости, 4, оф.303 83000 Ивано-Франковск Tel. +216 79 40 88 77 Fax +216 79 40 88 66 http://www.tms.com.tn tms@tms.com.tn Tel. +90-262-9991000-04 Fax +90-262-9991009 http://www.sew-eurodrive.com.tr sew@sew eurodrive.com.tr Tel. +90 322 359 94 15 Fax +90 322 359 94 16 Tel. +90 312 385 33 90 Fax +90 312 385 32 58 Tel. +90 224 443 45 60 Fax +90 224 443 45 58 Tel. +90-262-9991000-04 Fax +90-262-9991009 Tel. +90 232 469 62 64 Fax +90 232 433 61 05 Тел. +380 56 370 3211 Факс. +380 56 372 2078 http://www.sew-eurodrive.ua sew@sew eurodrive.ua Тел. +380 44 503 95 77 Факс. +380 44 503 95 78 kso@sew eurodrive.ua Тел. +380 62 38 80 545 Факс. +380 62 38 80 533 dso@sew eurodrive.ua Тел. +380 342 725 190 Факс. +380 342 725 191 ifso@sew-eurodrive.ua 14 Uruguay Assembly plant Sales Montevideo SEW EURODRIVE Uruguay, S. A. Jose Serrato 3569 Esqina Corumbe CP 12000 Montevideo Tel. +598 2 21181-89 Fax +598 2 21181-89 sewuy@sew eurodrive.com.uy USA Production plant Assembly plant Sales Service Southeast Region SEW EURODRIVE INC. 1295 Old Spartanburg Highway P.O. Box 518 Lyman, S.C. 29365 Tel. +1 864 439-7537 Fax Sales +1 864 439-7830 Fax Manufacturing +1 864 439-9948 Fax Assembly +1 864 439-0566 Fax Confidential/HR +1 864 949-5557 http://www.seweurodrive.com cslyman@seweurodrive.com Catalog CMP40 CMP112, CMPZ71 CMPZ100 415

14 Address Directory USA Assembly plants Sales Service Northeast Region SEW EURODRIVE INC. Pureland Ind. Complex 2107 High Hill Road, P.O. Box 481 Bridgeport, New Jersey 08014, USA Midwest Region Southwest Region Western Region SEW EURODRIVE INC. 2001 West Main Street Troy, Ohio 45373, USA SEW EURODRIVE INC. 3950 Platinum Way Dallas, Texas 75237, USA SEW EURODRIVE INC. 30599 San Antonio St. Hayward, CA 94544, USA Please contact us for other service center addresses in the USA. Tel. +1 856 467-2277 Fax +1 856 845-3179 csbridgeport@seweurodrive.com Tel. +1 937 335-0036 Fax +1 937 332-0038 cstroy@seweurodrive.com Tel. +1 214 330-4824 Fax +1 214 330-4724 csdallas@seweurodrive.com Tel. +1 510 487-3560 Fax +1 510 487-6433 cshayward@seweurodrive.com Venezuela Assembly plant Sales Service Valencia SEW EURODRIVE Venezuela S.A. Av. Norte Sur No. 3, Galpon 84-319 Zona Industrial Municipal Norte Valencia, Estado Carabobo, Venezuela Tel. +58 241 832-9804 Fax +58 241 838-6275 http://www.sew-eurodrive.com.ve ventas@sew eurodrive.com.ve sewfinanzas@cantv.net United Arab Emirates Sales Service Sharjah Copam Middle East (FZC) Sharjah Airport International Free Zone P.O. Box 120709 Sharjah Tel. +971 6 5578-488 Fax +971 6 5578-499 copam_me@eim.ae Vietnam Sales Ho-Chi-Minh- Stadt Hanoi All sectors except for ports and offshore: Nam Trung Co., Ltd 250 Binh Duong Avenue, Thu Dau Mot Town, Binh Duong Province HCM office: 91 Tran Minh Quyen Street District 10, Ho Chi Minh City Ports and offshore: DUC VIET INT LTD Industrial Trading and Engineering Services A75/6B/12 Bach Dang Street, Ward 02, Tan Binh District, 70000 Ho Chi Minh City Nam Trung Co., Ltd R.205B Tung Duc Building 22 Lang ha Street Dong Da District, Hanoi City Tel. +84 8 8301026 Fax +84 8 8392223 namtrungco@hcm.vnn.vn truongtantam@namtrung.com.vn khanh-nguyen@namtrung.com.vn Tel. +84 8 62969 609 Fax +84 8 62938 842 totien@ducvietint.com Tel. +84 4 37730342 Fax +84 4 37762445 namtrunghn@hn.vnn.vn Zambia Sales Kitwe EC Mining Limited Plots No. 5293 & 5294,Tangaanyika Road, Off Mutentemuko Road, Heavy Industrial Park, P.O.BOX 2337 Kitwe Tel. +260 212 210 642 Fax +260 212 210 645 sales@ecmining.com http://www.ecmining.com 416 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Index 19381212/EN 03/15 Index A Additional documentation... 11 Additional feature ventilation... 336 Ambient temperature, maximum... 37 Approved unit combinations... 302 Assignment table Cables for CMP servomotors... 344 Cables to CMP servomotors with BP brake.. 350 Cables to CMP servomotors with BY brake... 356, 358, 366, 367 Connectors and terminal boxes... 316 Encoder cables for connection option KK... 368 Encoder cables for plug connection option /KKS... 368 Power cables and plug connectors CMP... 324 Power cables and plug connectors for CMPZ motors... 325 Axial forces... 43 B B10d values... 304 Ball bearing combinations, approved... 43 BK brake BK brake coil resistance... 242 Block diagram of brake control, terminal box... 246 Braking contactor... 243 Cable routing... 243, 259 Description... 232 Dimensions drawings for brake controls... 247 Function... 234 General information... 234 Operating currents... 242 Principle... 233 Selecting the brake... 235 Sizing... 243, 259 Technical data... 241 Wiring diagram brake control plug connector... 244 Working capacity in case of emergency switching off... 239 Block diagram of BY brake control plug connectors... 286 Block diagram of BY brake control terminal box... 293 BP brake Block diagram of brake control, terminal box... 262 Brake coil resistance... 258 Braking contactor... 259 Cable routing... 243, 259 Description... 248 Dimension drawings for brake controls... 263 Function... 250 General information... 250 Operating currents... 257 Principle... 249 Selecting the brake... 251 Sizing... 243, 259 Technical data... 256 Wiring diagram for brake control plug connector... 260 Working capacity in case of emergency switching off... 255 BP/BK brake Important design information... 236, 252 brake control system Safety-rated... 301 Brake rectifier BME... 293 BMH... 294 BMK... 295 BMP... 294 BMV... 244, 260 BMV for CMP50, CMP63... 246 BMV for CMP71 to CMP100... 262 BS... 244, 260 BS for CMP50, CMP63... 246 BS for CMP71 to CMP100... 262 BSG... 296 Direct 24 V supply... 245, 261 Brakemotors... 16 BST Characteristic safety values... 304 Dimension drawings... 303 BST brake module... 301 BY brake Bestimmen der Bremsenspannung;Bremsenspannung BY-Bremse... 278 Catalog CMP40 CMP112, CMPZ71 CMPZ100 417

Index C Block diagram of brake control plug connectors... 286 Block diagram of brake control terminal box... 293 Braking torques... 281, 304 Braking work... 281, 304 BY(FS)... 298 Dimension drawings BY brake control... 297 Dimensioning and routing of the cable... 283 Emergency stop features... 271 General information... 265 Important design information... 267 Manual brake release... 282 Operating currents of BY brakes... 279 Principle of the BY brake... 265 Resistance brake coils... 280 Selecting the brake control system... 284 Selecting the brake in accordance with the project planning data... 266 Selecting the braking contactor... 283 Technical data... 273 Working capacity... 270 Cable specification Encoder cables... 392 Forced cooling fan cables... 394 Power cables... 388 Characteristic safety values... 312 Encoders... 311 Circuit breaker and protective equipment... 29 CMP product description Brakemotors... 16 CMP synchronous servomotors... 13 CMPZ synchronous servomotors... 13 Features of CMP. servomotors... 13 Output types of CMP motors... 15 Painting... 15 Rated speeds... 14 Thermal motor information with KTY... 313 Torque range... 14 Cold storage application... 37 Conformity with directives... 27 Conformity with standards... 27 Connection of signal plug connectors - encoder... 330 Connection of SM1/SB1 power plug connector -BP brake... 327 Connection of SM1/SB1 power plug connector, BY brake... 327 Connection of SMB/SBB power plug connectors - BP brake... 327 Connection of SMB/SBB power plug connectors - BY brake... 328 Connection option via terminal box... 331 Connection variants... 316 Copyright notice... 12 Corrosion protection... 19 D Degrees of protection according to IEC 60034 5... 41 Derating... 38 Designs, possible Brakemotors... 16 For international markets... 17 Dimension drawings BK brake controls... 247 BP brake controls... 263 Dimension drawings BST... 303 Dimension drawings BY brake control... 297 Dimension sheet information CMP... 170 Documentation, additional... 0 E Electrical characteristics... 39 EMC measures... 29 Encoder cables for CMP. servomotors... 380 Encoders... 305 F Safety-rated... 309 Forced cooling fan cables, CMP. servomotors.. 386 Functional safety... 18 BY brake... 298 Functional safety technology... 18 H Heavy load range... 0 I Interfaces Absolute... 311, 312 Sine/cosine... 311, 312 19381212/EN 03/15 418 Catalog CMP40 CMP112, CMPZ71 CMPZ100

Index 19381212/EN 03/15 International markets... 17 L Light load range... 0 M Manual brake release retrofit set... 282 Manual brake release, BY brake... 282 Maximum ambient temperature... 37 Maximum speed... 70 Mechanical characteristics... 39 Motor operating temperatures... 15 Motor protection... 313 Thermal motor protection with PTC resistor. 314 Motor types N Encoders... 305 Nameplate, example... 28 No-load starting frequency, BY brake... 277 Number of poles... 14 O Operating currents BP brake... 257 Overhung loads... 43 P Performance level... 298 Plug connector connection option... 322 Plug connectors, connection option... 322 Power cables and plug connectors CMP... 324 Power cables and plug connectors for CMPZ motors... 325 Power cables for CMP. motors... 372 Preventive measures... 29 Product groups... 8 Product names... 12 Production description of BY brakes Basic function... 265 Project planning Approved ball bearing types... 43 Derating for increased ambient temperature.. 38 Mechanical characteristics;electrical characteristics... 39 Overhung loads;axial loads... 43 Product characteristics of inverters... 69 Rated data... 28 Thermal characteristics... 37 Project planning for cable cross section... 342 Project planning notes CMP Project planning procedure... 37 Project planning procedure... 33 R Part 1, servo gear units... 33 Part 2, servo gear units... 34 Part 3, servomotors... 35 Part 4, servomotors... 36 Rated data... 28 Resistances BP-Bremsspulen... 258 Retrofit set for manual brake release... 282 S Safety characteristics... 311 Safety function... 298 SBA... 298 SBH... 298 Serial number... 26 SEW-EURODRIVE Group of companies... 7 SEW EURODRIVE Products... 8 Systems... 8 Standard conformity... 27 Standard type Connection variants... 316 Motor protection... 313 Standards and regulations... 27 Structure of prefabricated cables for CMP. servomotors... 369 Surface protection... 19 T Technical data BK brake... 241 BP brake... 256 Characteristic safety values BST... 304 Forced cooling fan... 337 Technical data of BY brakes Brake coil resistance... 280 Braking torques... 281, 304 Catalog CMP40 CMP112, CMPZ71 CMPZ100 419

Index Braking work... 281 Operating currents... 279 Technical data of CMP Thermal motor information with KTY... 313 Technical data of CMP and CMPZ servomotors CMPZ motors... 77 Technical data of the BY brake... 273 Terminal box... 22 CMP71 CMP100 connection... 334 Connection of CMP50 and CMP63... 332 Terminal box, connection option... 331 Thermal characteristics... 37 Thermal motor protection... 313 Trademarks... 12 Type designation Connection variants... 25 Encoder... 24 Mechanical attachments... 24 Motor series... 24 Temperature sensor and temperature detection... 24 Ventilation... 25 Type designation of a servomotor... 26 U unit combinations Approved... 302 UWU51A switched-mode power supply... 338 V Ventilation, additional feature... 336 VR forced cooling fan W Mechanical installation... 336 Wiring diagram for RH1M resolver signal plug connectors... 329 Wiring diagrams of the brake control BY brake plug connector BME... 286 BMH... 288 BMK... 289 BMKB... 290 BMP... 287 BMV... 291 BSG... 292 19381212/EN 03/15 420 Catalog CMP40 CMP112, CMPZ71 CMPZ100

SEW-EURODRIVE Driving the world SEW-EURODRIVE GmbH & Co KG P.O. Box 3023 76642 BRUCHSAL GERMANY Phone +49 7251 75-0 Fax +49 7251 75-1970 sew@sew-eurodrive.com www.sew-eurodrive.com