PICTORIAL INDEX FLEXISTRUT CHANNELS PAGE 6 to 23 CONCRETE INSERTS PAGE 24-25 FLEXISTRUT CHANNEL NUTS PAGE 26 CLOSURE STRIP AND END CAPS PAGE 26 FLAT PLATE FITTINGS PAGE 27 and 35 90 DEGREE ANGLE FITTINGS PAGE 28 to 30 Z SHAPE FITTINGS PAGE 31 U SHAPE FITTINGS PAGE 32 to 33 WING SHAPE FITTINGS PAGE 34 BASE PLATES PAGE 36 ANGULAR FITTINGS PAGE 37 SLOTTED ANGLE / DURAGAL ANGLE PAGE 38 BEAM CLAMPS PAGE 39 PURLIN CLIPS PAGE 40 ALLTHREAD ROD CLAMPS PAGE 40 ALLTHREAD ROD PAGE 41 WEDGE NUTS PAGE 41 EYE NUTS PAGE 41 TROLLEY ASSEMBLIES PAGE 42 ROD CUTTERS PAGE 43 NUTS, BOLTS AND WASHERS PAGE 44 to 47 ROD COUPLERS PAGE 47 ANCHORS PAGE 47 to 49 ANCHORS PAGE 47 to 49 1
PICTORIAL INDEX TEK SCREWS AND RIVETS PAGE 50 DRILLBITS PAGE 51 ABRASIVES PAGE 52 HOLESAWS PAGE 53 GROMMETS PAGE 54 FLEXIDEXTITE PAGE 54 TAPES PAGE 54 TAPES PAGE 54 CABLE TIES PAGE 55 SEALANT PAGE 55 SPRAY CANS PAGE 55 PIPE MARKERS PAGE 56 ZIP CLIP HANGING SYSTEM PAGE 57 to 58 FLEXISTRUT DRIVE PIN PAGE 59 NUT CLAMPS AND FERRULES PAGE 60 to 61 STANDARD U-BOLTS PAGE 62 DOMESTIC PLUMBING PRODUCTS PAGE 63 to 64 DOMESTIC PLUMBING PRODUCTS PAGE 63 to 64 STANDARD DOUBLE BOLTED CLAMPS PAGE 65 to 66 DOUBLE BOLTED CLAMPS AND FERRULES PAGE 67 to 68 STANDARD SADDLE CLAMPS PAGE 69 to 70 STANDARD BAND CLAMPS PAGE 71 to 72 STANDARD BAND CLAMPS AND FERRULES PAGE 73 to 74 FAST CLIPS PAGE 75 2
PICTORIAL INDEX TWO PIECE CHANNEL CLIPS PAGE 76 REFRIGERATION CHANNEL CLIPS PAGE 77 TWO PIECE CHANNEL CLIPS WITH BARRIER STRIP PAGE 78 TWO PIECE CHANNEL CLIPS AND FERRULE PAGE 79 to 80 TIMBER FERRULES PAGE 81 to 82 FLEXI BLOCKS PAGE 83 to 84 P/U BLOCKS PAGE 85 ONE PIECE CHANNEL CLIPS PAGE 86 SLIDE GUIDES PAGE 87 to 96 ROLLER GUIDES PAGE 97 to 102 EYEBOLTS AND SPHERICAL WASHERS PAGE 103 HANGER CLEVIS PAGE 103 BLADE END HANGERS PAGE 103 CANTILEVER FITTINGS PAGE 104 CANTILEVER BRACKETS PAGE 105 STANDARD CLEVIS PIPE HANGERS PAGE 106 BEAM CLAMPS FOR FLEXISTRUT CHANNEL PAGE 107 BEAM ATTACHMENTS PAGE 108 FLOOR MOUNTED RISER GUIDES PAGE 109 to 111 FLOOR MOUNTED ANCHORS PAGE 112 WALL MOUNTED ANCHOR PAGE 113 3
PICTORIAL INDEX SPIDER CLAMPS FOR STEAM PAGE 114 to 115 PIPE ROLLERS PAGE 116 to 117 FLEXICUSHION FLEXIBARRIER PAGE 118 LIGHT DUTY / MED DUTY BOLTED CLAMPS PAGE 119 and 122 LIGHT DUTY / MED DUTY YOKE CLAMPS PAGE 120 and 123 MEDIUM DUTY SADDLES PAGE 121 EYE NUT PAGE 124 GAS RISER PIPE SUPPORTS PAGE 125 to 130 VIBRATION ISOLATION PAGE 131 to 135 VIBRATION ISOLATION PAGE 131-135 REGISTER SPRINGS PAGE 135 DUCT CLEAT PAGE 135 DUCT BRACKETS PAGE 136 BRACING BRACKETS PAGE 137 100 SERIES SHANKLESS CLIPS PAGE 138 200 SERIES NUT CLIPS PAGE 139 300 SERIES SHANK CLIPS PAGE 140 to 141 STANDARD PEAR BANDS PAGE 142 ACOUSTIC PIPE CLIPS PAGE 143 STANDARD SADDLE CLAMPS FOR F.R.C. PAGE 144 STANDARD BOLTED CLAMPS FOR F.R.C. PAGE 145 FIRE PROTECTION SADDLES PAGE 146 FIRE PROTECTION TWIST CLIPS PAGE 146 FIRE PROTECTION EF400 NUT CLIPS PAGE 146 FIRE PROTECTION PEAR BANDS PAGE 147 4
PICTORIAL INDEX FIRE PROTECTION MOUNTING PLATES PAGE 148 FIRE PROTECTION ANGLE BRACKETS PAGE 149 FIRE PROTECTION CLAMPS PAGE 150 FIRE PROTECTION BAND CLAMPS PAGE 150 FIRE PROTECTION PURLIN CLIPS PAGE 150 FIRE PROTECTION PURLIN CLIPS PAGE 150 CABLE LADDER PAGE 151 PERFORATED TRAY PAGE 152 LADDER TRAY PAGE 153 HOLD DOWN BRACKETS PAGE 154 BARRIER STRIP PAGE 154 FISH PLATES PAGE 155 LINK PLATES PAGE 155 RADIUS PLATES PAGE 155 ELECTRICAL BOLTS AND NUTS PAGE 155 TRAPEZE SUPPRT PAGE 156 T-X BRACKETS PAGE 156 FM2377 JOINERS PAGE 157 TRIFOIL AND QUADFOIL CLAMPS PAGE 157 FMC CLAMPS PAGE 158 PETROCHEM PRODUCTS PAGE 160-165 PETROCHEM PRODUCTS PAGE 160-165 PETROCHEM PRODUCTS PAGE 160-165 5
FLEXISTRUT CHANNEL FM1000 FM1000 WEIGHT: THICKNESS: MATERIAL: FINISHES: 2.60kg/m 2.5mm 250MPa (min yield stress) mild steel Plain, Galvabond, Hot Dipped Galvanised, Polyester Powder Coated, 316 GR Stainless Steel. (Other finishes available on request) SECTION PROPERTIES X-X AXIS Y-Y AXIS CHANNEL WEIGHTkg/m AREA OF SECTION mm 2 MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 2 RADIUS OF GYRATION r mm MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 3 RADIUS OF GYRATION r mm FM1000 2.60 331.070 2.925 14.5 0.093 4.452 16.7 FM1001 5.20 662.319 7.715 22.1 0.186 8.904 16.7 FM1000T 14mm x 30mm Slots at approx. 50mm centres. 6
FM1000 CHANNEL COMBINATIONS FM1000 FM1000T FM1001 FM1001-3 FM1001A FM1001A3 FM1001B FM1001B3 FM1001C 7
CHANNEL COMBINATIONS FM1000 FM1001C3 FM1001C41 FM1001D3 FM1003 FM1003-1 FM1004A 8
FM1000 TECHNICAL DATA LOADING CRITERIA -Loads indicated below are in accordance with AS/NZS 4600 1996. Cold-formed steel structure - Minimum yield stress : FY = 210 Mpa - Beam Load and deflection data are based on a uniformly loaded simply supported beam - For point load at mid span multiply maximum allowable load by.5 and deflection by.8 - Load values are for bending about the X-X axis only BEAM SPAN OR UNSUPPORTED COLUMN HEIGHT (mm) CHANNEL TYPE BEAM MAX. ALLOWABLE LOAD (Kg) DEFLECTION AT MAX. ALLOWABLE COLUMN MAX. ALLOWABLE LOAD (KG) LOAD (mm) 250 FM1000 1485 0.22 4550 250 FM1001 2565 0.08 9770 500 FM1000 743 0.87 3685 500 FM1001 1958 0.50 9410 750 FM1000 495 1.97 2825 750 FM1001 1305 1.13 8835 1000 FM1000 350 3.50 2145 1000 FM1001 980 2.01 8091 1250 FM1000 296 5.47 1642 1250 FM1001 784 3.14 7225 1500 FM1000 248 7.87 1321 1500 FM1001 655 4.49 6290 1750 FM1000 215 10.71 1100 1750 FM1001 560 6.13 5342 2000 FM1000 186 13.99 936 2000 FM1001 489 8.01 4420 2250 FM1000 165 17.71 806 2250 FM1001 436 10.15 3560 2500 FM1000 148 21.86 700 2500 FM1001 395 12.52 2886 2750 FM1000 136 26.45 615 2750 FM1001 358 15.10 2385 3000 FM1000 125 31.46 N/R 3000 FM1001 325 18.03 2003 9
FLEXISTRUT CHANNEL FM2000 FM2000 WEIGHT: THICKNESS: MATERIAL: FINISHES: 1.80kg/m 1.6mm 250MPa (min yield stress) mild steel Plain, Galvabond, Hot Dipped Galvanised, Polyester Powder Coated (Other finishes available on request) SECTION PROPERTIES X-X AXIS Y-Y AXIS CHANNEL WEIGHTkg/m AREA OF SECTION mm 2 MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 2 RADIUS OF GYRATION r mm MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 3 RADIUS OF GYRATION r mm FM2000 1.80 229 0.053 2.300 15.2 0.066 3.150 16.9 FM2001 3.60 458 0.263 6.325 23.8 0.132 6.400 16.9 FM2000T 14mm x 30mm Slots at approx. 50mm centres. 10
FM2000 CHANNEL COMBINATIONS FM2000 FM2000T FM2001 FM2001A FM2001B FM2001C FM2001C3 FM2001C4 FM2003 11
TECHNICAL DATA FM2000 LOADING CRITERIA -Loads indicated below are in accordance with AS/NZS 4600 1996. Cold-formed steel structure - Minimum yield stress : FY = 210 Mpa - Beam Load and deflection data are based on a uniformly loaded simply supported beam - For point load at mid span multiply maximum allowable load by.5 and deflection by.8 - Load values are for bending about the X-X axis only BEAM SPAN OR UNSUPPORTED COLUMN HEIGHT (mm) CHANNEL TYPE BEAM MAX. ALLOWABLE LOAD (Kg) DEFLECTION AT MAX. ALLOWABLE COLUMN MAX. ALLOWABLE LOAD (KG) LOAD (mm) 250 FM2000 1032 0.21 3293 250 FM2001 1180 0.05 7085 500 FM2000 610 0.93 2655 500 FM2001 1180 0.36 6820 750 FM2000 405 2.11 1922 750 FM2001 1110 1.16 6397 1000 FM2000 305 3.77 1292 1000 FM2001 835 2.08 5850 1250 FM2000 245 5.86 904 1250 FM2001 670 3.25 5216 1500 FM2000 205 8.49 690 1500 FM2001 555 4.68 4533 1750 FM2000 175 11.52 557 1750 FM2001 476 6.34 3840 2000 FM2000 135 8.40 547 2000 FM2001 350 4.62 3178 2250 FM2000 127 19.06 403 2250 FM2001 371 10.49 2549 2500 FM2000 120 23.54 354 2500 FM2001 334 12.99 2065 2750 FM2000 110 28.48 315 2750 FM2001 300 15.67 2065 3000 FM2000 102 33.90 283 3000 FM2001 278 18.65 1434 12
FM3300 FLEXISTRUT CHANNEL FM3300 WEIGHT: THICKNESS: MATERIAL: FINISHES: 1.83kg/m 2.5mm 250MPa (min yield stress) mild steel Plain, Galvabond, Hot Dipped Galvanised, Polyester Powder Coated (Other finishes available on request) SECTION PROPERTIES X-X AXIS Y-Y AXIS CHANNEL WEIGHTkg/m AREA OF SECTION mm 2 MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 2 RADIUS OF GYRATION r mm MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 3 RADIUS OF GYRATION r mm FM3300 1.83 233 0.013 1.000 7.6 0.056 2.662 15.4 FM3301 3.66 466 0.064 2.843 11.6 0.111 5.331 15.4 FM3300T 14mm x 30mm Slots at approx. 50mm centres. 13
CHANNEL COMBINATIONS FM3300 FM3300 FM3301 FM3300T 14
FM3300 TECHNICAL DATA LOADING CRITERIA -Loads indicated below are in accordance with AS/NZS 4600 1996. Cold-formed steel structure - Minimum yield stress : FY = 210 Mpa - Beam Load and deflection data are based on a uniformly loaded simply supported beam - For point load at mid span multiply maximum allowable load by.5 and deflection by.8 - Load values are for bending about the X-X axis only BEAM SPAN OR UNSUPPORTED COLUMN HEIGHT (mm) CHANNEL TYPE BEAM MAX. ALLOWABLE LOAD (Kg) DEFLECTION AT MAX. ALLOWABLE COLUMN MAX. ALLOWABLE LOAD (KG) LOAD (mm) 250 FM3300 554 0.42 3490 250 FM3301 1560 0.26 7319 500 FM3300 278 1.69 2778 500 FM3301 780 1.02 6734 750 FM3300 185 3.78 1943 750 FM3301 520 2.27 5860 1000 FM3300 139 6.75 1210 1000 FM3301 392 4.03 4820 1250 FM3300 112 10.54 792 1250 FM3301 315 6.30 3750 1500 FM3300 93 15.18 560 1500 FM3301 261 9.07 2752 1750 FM3300 79 20.65 0.00 1750 FM3301 225 12.35 2022 2000 FM3300 70 26.96 0.00 2000 FM3301 196 16.10 1550 2250 FM3300 62 34.15 0.00 2250 FM3301 175 20.40 1225 2500 FM3300 56 42.15 0.00 2500 FM3301 157 25.15 0.00 2750 FM3300 51 50.98 0.00 2750 FM3301 143 30.45 0.00 3000 FM3300 47 60.65 0.00 3000 FM3301 131 36.20 0.00 15
FLEXISTRUT CHANNEL FM4000 FM4000 WEIGHT: THICKNESS: MATERIAL: FINISHES: 1.27kg/m 1.6mm 250MPa (min yield stress) mild steel Plain, Galvabond, Hot Dipped Galvanised, Polyester Powder Coated (Other finishes available on request) SECTION PROPERTIES X-X AXIS Y-Y AXIS CHANNEL WEIGHTkg/m AREA OF SECTION mm 2 MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 2 RADIUS OF GYRATION r mm MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 3 RADIUS OF GYRATION r mm FM4000 1.27 161 0.010 0.787 7.8 0.040 1.881 15.6 FM4001 2.54 322 0.045 2.084 11.8 0.079 3.765 15.6 FM4000T 14mm x 30mm Slots at approx. 50mm centres. 16
FM4000 CHANNEL COMBINATIONS FM4000 FM4000T FM4001 FM4002-1 FM4002-2 FM4003 FM4004 FM42001C FM42002 17
TECHNICAL DATA FM4000 LOADING CRITERIA -Loads indicated below are in accordance with AS/NZS 4600 1996. Cold-formed steel structure - Minimum yield stress : FY = 210 Mpa - Beam Load and deflection data are based on a uniformly loaded simply supported beam - For point load at mid span multiply maximum allowable load by.5 and deflection by.8 - Load values are for bending about the X-X axis only BEAM SPAN OR UNSUPPORTED COLUMN HEIGHT (mm) CHANNEL TYPE BEAM MAX. ALLOWABLE LOAD (Kg) DEFLECTION AT MAX. ALLOWABLE COLUMN MAX. ALLOWABLE LOAD (KG) LOAD (mm) 250 FM4000 422.45 2238 250 FM4001 1040.25 4906 500 FM4000 212 1.78 1631 500 FM4001 557 1.04 4525 750 FM4000 142 3.99 1050 750 FM4001 372 2.34 3955 1000 FM4000 107 7.10 655 1000 FM4001 280 4.15 3275 1250 FM4000 85 11.10 455 1250 FM4001 223 6.50 2570 1500 FM4000 71 15.95 336 1500 FM4001 186 9.32 1910 1750 FM4000 61 21.70 0.00 1750 FM4001 160 12.70 14.01 2000 FM4000 53 28.33 0.00 2000 FM4001 140 16.60 10.75 2250 FM4000 48 35.90 0.00 2250 FM4001 124 20.95 8.50 2500 FM4000 43 44.30 0.00 2500 FM4001 112 25.90 0.00 2750 FM4000 39 53.60 0.00 2750 FM4001 102 31.30 0.00 3000 FM4000 36 63.60 0.00 3000 FM4001 94 37.25 0.00 18
FM5500 FLEXISTRUT CHANNEL FM5500 WEIGHT: THICKNESS: MATERIAL: FINISHES: 3.41kg/m 2.5mm 250MPa (min yield stress) mild steel Plain, Galvabond, Hot Dipped Galvanised, Polyester Powder Coated (Other finishes available on request) SECTION PROPERTIES X-X AXIS Y-Y AXIS CHANNEL WEIGHTkg/m AREA OF SECTION mm 2 MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 2 RADIUS OF GYRATION r mm MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 3 RADIUS OF GYRATION r mm FM5500 3.41 434 0.198 5.731 21.3 0.132 6.329 17.4 FM5501 6.82 868 1.054 16.992 31.8 0.262 12.664 17.4 FM5500T 14mm x 30mm Slots at approx. 50mm centres. 19
CHANNEL COMBINATIONS FM5500 FM5500 FM5501 FM5500T 20
FM5500 TECHNICAL DATA LOADING CRITERIA -Loads indicated below are in accordance with AS/NZS 4600 1996. Cold-formed steel structure - Minimum yield stress : FY = 210 Mpa - Beam Load and deflection data are based on a uniformly loaded simply supported beam - For point load at mid span multiply maximum allowable load by.5 and deflection by.8 - Load values are for bending about the X-X axis only BEAM SPAN OR UNSUPPORTED COLUMN HEIGHT (mm) CHANNEL TYPE BEAM MAX. ALLOWABLE LOAD (Kg) DEFLECTION AT MAX. ALLOWABLE COLUMN MAX. ALLOWABLE LOAD (KG) LOAD (mm) 250 FM5500 2705 0.14 5704 250 FM5501 2705 0.03 1222 500 FM5500 1385 0.56 4592 500 FM5501 2705 0.20 1182 750 FM5500 924 1.28 3379 750 FM5501 2705 0.70 1119 1000 FM5500 693 2.28 2386 1000 FM5501 2050 1.26 1036 1250 FM5500 555 3.58 1739 1250 FM5501 1641 1.97 9372 1500 FM5500 462 5.14 1377 1500 FM5501 1368 2.85 8299 1750 FM5500 396 7.00 1149 1750 FM5501 1173 3.88 7189 2000 FM5500 348 9.17 990 2000 FM5501 1026 5.07 6092 2250 FM5500 309 11.60 873 2250 FM5501 912 6.42 5049 2500 FM5500 278 14.30 782 2500 FM5501 821 7.92 3393 2750 FM5500 253 17.30 644 2750 FM5501 747 9.60 2852 3000 FM5500 232 20.60 590 3000 FM5501 685 11.40 2429 21
FM8300 FLEXISTRUT CHANNEL FM8300 WEIGHT: THICKNESS: MATERIAL: FINISHES: 4.16kg/m 2.5mm 250MPa (min yield stress) mild steel Plain, Galvabond, Hot Dipped Galvanised, Polyester Powder Coated (Other finishes available on request) SECTION PROPERTIES X-X AXIS Y-Y AXIS CHANNEL WEIGHTkg/m AREA OF SECTION mm 2 MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 2 RADIUS OF GYRATION r mm MOMENT OF INERTIA I 10 6 mm 4 SECTION MODULUS Z 10 3 mm 3 RADIUS OF GYRATION r mm FM8300 4.16 541.4285 9.64 2.81.1700 8.240 17.7 FM8301 8.32 1082 2.4317 29.44 4.74.3400 16.480 17.7 FM8300T 14mm x 30mm Slots at approx. 50mm centres. 22
FM8300 CHANNEL COMBINATIONS FM8300 FM8301 FM8300T 23
CONCRETE INSERT FM1000CI Standard Length: Foam: Finish: Loading Data: Recommended Pullout Loading: Factor of Safety Approximately 3 Mass: 2.80kg/m Note: Exercise care during installation - Don t bend lugs. 3 Metres Injected Polyurethane Hot Dipped Galvanised 316 GR Stainless Steel Because the support capacity of any concrete insert depends largely on the strength of the concrete used, we cannot guarantee any particular load. Inserts 300mm and over 8.83kN per 300mm. 24
FM3300CI CONCRETE INSERT Standard Length: Foam: Finish: Loading Data: Recommended Pullout Loading: Factor of Safety Approximately 3 Mass: 1.94kg/m Note: Exercise care during installation - Don t bend lugs. 3 Metres Injected Polyurethane Hot Dipped Galvanised 316 GR Stainless Steel Because the support capacity of any concrete insert depends largely on the strength of the concrete used, we cannot guarantee any particular load. Inserts 300mm and over 6.37kN per 300mm. 25
FLEXISTRUT CHANNEL NUTS CHANNEL NUTS WITH SPRINGS PART NO. THREAD SUIT CHANNEL BOX QTY FM1006 M06 FM1000 / FM2000 100 FM1007 M08 FM1000 / FM2000 100 FM1008 M10 FM1000 / FM2000 100 FM1010 M12 FM1000 / FM2000 100 FM1012S M16 FM1000 / FM2000 100 FM5508 M10 FM5500 100 FM5510 M12 FM5500 100 FM4006 M06 FM3300 / FM4000 100 FM4007 M08 FM3300 / FM4000 200 FM4008 M10 FM3300 / FM4000 200 FM4010 M12 FM3300 / FM4000 200 FM4012S M16 FM3300 / FM4000 100 CHANNEL NUTS WITHOUT SPRINGS PART NO. THREAD SUIT CHANNEL BOX QTY FM3016 M6 TRUNKING NUT, ALL CHANNELS 200 FM3006 M6 ALL CHANNELS 100 FM3007 M8 ALL CHANNELS 100 FM3008 M10 ALL CHANNELS 100 FM3010 M12 ALL CHANNELS 100 FM1012 M16 ALL CHANNELS 100 FINISH: ZINC PLATED GALVANISED AND STAINLESS STEEL AVAILABLE ON REQUEST CLOSURE STRIP AND END CAPS FM1184-PLA FM2240 FM4240 FM5580 FM2240 FOR FM1000 FM2240 FOR FM2000 FM4240 FOR FM3300 FM4240 FOR FM4000 FM5580 FOR FM5500 FM1184-PLA END CAPS GREY PVC 26
FM1031 FM1036 FM1358 FM2324 FM2325 FLAT PLATE FITTINGS FM1358 BOX QTY:20 FM1031 BOX QTY25 FM1036 BOX QTY:25 FM2325 BOX QTY:25 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) FM2324 BOX QTY:25 27
90 DEGREE ANGLE FITTINGS FM1026 FM1068 FM1326 FM1346 FM1458 FM1068 BOX QTY:50 FM1026 BOX QTY:50 FM1326 BOX QTY:25 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) FINISH: GALVANISED FM1346 BOX QTY:25 FM1458 BOX QTY:25 28
FM1033 FM1038 FM1325 FM2484 90 DEGREE ANGLE FITTINGS FM1325 BOX QTY:20 FM2484 BOX QTY:10 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) FM1038 BOX QTY:25 FM1033 BOX QTY:25 29
90 DEGREE ANGLE FITTINGS FM1034 FM1035 FM1037 FM1037 BOX QTY:25 FM1034 BOX QTY:25 FM1035 BOX QTY:25 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) 30
FM1045 FM1453 FM1736 FM4045 FM5545 Z SHAPE FITTINGS FM1045 BOX QTY:25 FM1453 BOX QTY:20 FM4045 BOX QTY:25 FM1736 BOX QTY:25 FM5545 BOX QTY:25 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) 31
U SHAPE FITTINGS FM1044 FM1047 FM4047 FM5547 FM1047 BOX QTY:20 FM5547 BOX QTY:10 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) FM1044 BOX QTY:25 FM4047 BOX QTY:20 32
FM1046 FM1376 FM1377 FM1834 FM1834A FM4376 U SHAPE FITTINGS FM1834 BOX QTY:20 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) FM1834A FM1046 BOX QTY:25 FM4376 BOX QTY:25 FM1376 BOX QTY:20 FM1377 BOX QTY:10 33
WING SHAPE FITTINGS FM2223 FM2224 FM2228 FM2346 FM2223 BOX QTY:10 FM2224 BOX QTY:10 FM2228 BOX QTY:10 FM2346 BOX QTY:10 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) 34
FM1064 FM1065 FM1066 FM1067 FM1941 FLAT PLATE FITTINGS FM1064 BOX QTY:50 Part No. H FM1062-9 FM1063-11 FM1064-14 FM1964-18 FM1065 BOX QTY:50 FM1066 BOX QTY:20 FM1067 BOX QTY:25 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) 35 FM1941 BOX QTY:25
BASE PLATES FM2072A FM2072S1 FM2073 FM2073L FM2073 BOX QTY:10 Hole Size 19MM Hole Size M22 FM2072A BOX QTY:10 FM2072S1 BOX QTY:20 NOTE: STD FINISH Z.P. OTHER FINISHES AVAIL. ALL HOLES 14mm MATERIAL 40 x 6 (U.N.O) FM2073L 36
FM1546 FM2095 FM2097 FM2101 FM2103 FM2106 FM2108 FM1186 FM2452 PART NO. A B C FM2095 75 91 43 FM2097 60 86 48 FM1546 45 76 60 ANGULAR FITTINGS PART NO. A B FM2101 30 83 FM2103 15 84 FM2452 PART NO. A FM2106 75 FM2108 60 FM1186 45 37
DURAGAL SLOTTED ANGLE / DURAGAL ANGLE EF1500 EF1510 DURAGAL SLOTTED ANGLE PART NO. MATERIAL SLOT STANDARD LENGTH EF1500-030 30x30x2.5 11x18 3mt EF1500-040 40x40x2.5 12x25 6mt EF1500-050 50x50x5 14x30 3mt EF1500-065 65x65x5 18x32 6mt MIN. YIELD STRESS 400MPa MIN. TENSILE STRENGTH 450MPa FINISH: DURAGAL DURAGAL ANGLE MIN. YIELD STRESS 400MPa MIN. TENSILE STRENGTH 450MPa STANDARD LENGTH 6M PART NO. MATERIAL EF1510-30/2.5 30 x 30 x 2.5 EF1510-40/2.5 40 x 40 x 2.5 EF1510-40/4.0 40 x 40 x 4.0 EF1510-50/2.5 50 x 50 x 2.5 EF1510-50/4.0 50 x 50 x 4.0 EF1510-50/5.0 50 x 50 x 5.0 EF1510-65/4.0 65 x 65 x 4.0 EF1510-65/5.0 65 x 65 x 5.0 EF1510-75/4.0 75 x 75 x 4.0 EF1510-75/5.0 75 x 75 x 5.0 FINISH: DURAGAL 38
EF1600 EF1700 EF1750 FM2676 FM2683 BEAM CLAMPS EF1600 BEAM CLAMP PART NO ROD DIA. EF1600-M8 M8 EF1600-M10 M10 EF1600-M12 M12 EF1600-M16 M16 BOX QTY : 50 FINISH: ZINC PLATED EF1700 BEAM CLAMP PART NO ROD DIA. EF1700-M10 M10 FINISH: ZINC PLATED FM2683 EF1750 L.D. BEAM CLAMP PART NO ROD DIA. EF1750-M10 M10 BOX QTY : 50 FINISH: GALVANISED FM2676 FINISH: GALVANISED BOX QTY:25 FINISH: GALVANISED BOX QTY:20 FM2676 beam clamp application provides a means of rod suspension, either fixed, or where a free swing of up to 15 degrees is required. Clamp will accommodate M6, M8 M10 or M12 rods. Clamp may also be used with FM2683 as illustrated in application drawing. 39
PURLIN CLIPS / ROD CLAMPS EF14-TI PURLIN CLIP PART NO ROD DIA. BOX QTY EF14TI-M6 M6 100 EF14TI-M8 M8 100 EF14TI-M10 M10 100 FINISH: ZINC PLATED EF1900 EF14-TI EF1900 EF2000 EF2050 EF14TI EF1900 PURLIN CLIP PART NO ROD DIA. BOX QTY EF1900-M8 M8 100 EF1900-M10 M10 50 EF1900-M12 M12 50 FINISH: ZINC PLATED EF2000 PURLIN CLIP PART NO ROD DIA. BOX QTY EF2000-M8 M8 100 EF2000-M10 M10 100 EF2000-M12 M12 100 FINISH: ZINC PLATED EF2000 EF2050 THREADED ROD CLAMP PART NO ROD DIA. BOX QTY EF2050-M10 M10 100 FINISH: ZINC PLATED EF2050 40
EF1800 FM150 FM1810 FM1820 ALLTHREAD ROD / ROD ACCESSORIES FM150 ALLTHREAD PART NO ROD DIA. FM150-M6 M6 FM150-M8 M8 FM150-M10 M10 FM150-M12 M12 FM150-M16 M16 FM150-M20 M20 FINISH: ZINC PLATED ALSO AVAILABLE GALVANISED AND STAINLESS STEEL. STANDARD LENGTHS 1m, 3m EF1800 WEDGE NUT PART NO ROD DIA. EF1800-M6 M6 EF1800-M8 M8 EF1800-M10 M10 EF1800-375 3/8 BSW FINISH: ZINC PLATED FM1810 EYE NUT PART NO ROD DIA. FM1810-M6 M6 FM1810-M8 M8 FM1810-M10 M10 FM1810-M12 M12 FM1810-M16 M16 FM1810-M20 M20 FINISH: ZINC PLATED FM1820 DROP IN ANCHOR PART NO ROD DIA. FM1820-M6 M6 FM1820-M8 M8 FM1820-M10 M10 FM1820-M12 M12 FM1820-M16 M16 FM1820-M20 M20 FINISH: ZINC PLATED 41
TROLLEY ASSEMBLIES CURTAIN SLIDERS FM2749 BOX QTY:50 FM2749 FM2750 FM2751 FM2950 FM5349 FM2751 FM2950 BOX QTY:20 FM2750 BOX QTY:25 FM5349 CURTAIN TRACK SLIDERS FINISH: ZINC PLATED BOX QTY:100 42
FM101 FLEXISTRUT THREADED ROD CUTTERS FM101-M10 M10 ROD CUTTER FM101-M12 M12 ROD CUTTER Cuts threaded rod with little effort. Thread not damaged after cutting. No burr removal required, enabling immediate use of Allthread. Light Weight and Compact at 4.5kg, 760mm long. Cutting components made from heat treated alloy steel for sharpness and durability. Jaws available to suit 6mm, 8mm and 10mm allthread compatable with M10 Rod Cutter Jaws available to suit 12mm allthread compatable with M12 Rod Cutter 43
HEX BOLTS AND NUTS PART NO. BOLT DIA. LENGTH BOX QTY HBNM6x20 M6 20 200 HBNM6x25 M6 25 200 HBNM6x30 M6 30 200 HBNM6x40 M6 40 200 HBNM6x50 M6 50 200 M6 HBNM8x20 M8 20 200 HBNM8x25 M8 25 200 HBNM8x30 M8 30 200 HBNM8x40 M8 40 200 HBNM8x50 M8 50 150 HBNM8x55 M8 55 150 HBNM8x60 M8 60 150 HBNM8x65 M8 65 150 HBNM8x75 M8 75 100 HBNM8x100 M8 100 100 M8 HBNM10x16 M10 16 150 HBNM10x20 M10 20 150 HBNM10x25 M10 25 150 HBNM10x30 M10 30 150 HBNM10x35 M10 35 150 HBNM10x40 M10 40 150 HBNM10x45 M10 45 150 HBNM10x50 M10 50 75 HBNM10x55 M10 55 75 HBNM10x60 M10 60 75 HBNM10x65 M10 65 75 HBNM10x70 M10 70 75 HBNM10x75 M10 75 75 HBNM10x80 M10 80 75 HBNM10x100 M10 100 50 HBNM10x120 M10 120 50 HBNM10x140 M10 140 50 HBNM12x25 M12 25 250 HBNM12x30 M12 30 250 HBNM12x35 M12 35 200 HBNM12x40 M12 40 200 HBNM12x45 M12 45 175 HBNM12x50 M12 50 175 HBNM12x55 M12 55 150 HBNM12x60 M12 60 150 HBNM12x65 M12 65 150 HBNM12x75 M12 75 150 HBNM12x100 M12 100 100 HBNM12x120 M12 120 100 PART NO. BOLT DIA. LENGTH BOX QTY HBNM16x25 M16 25 125 HBNM16x30 M16 30 100 HBNM16x35 M16 35 100 HBNM16x40 M16 40 100 HBNM16x45 M16 45 100 HBNM16x50 M16 50 100 HBNM16x55 M16 55 75 HBNM16x60 M16 60 75 HBNM16x65 M16 65 75 HBNM16x70 M16 70 75 HBNM16x75 M16 75 75 HBNM16x80 M16 80 75 HBNM16x85 M16 85 75 HBNM16x90 M16 90 75 HBNM16x100 M16 100 50 HBNM16x110 M16 110 50 HBNM16x120 M16 120 50 HBNM16x130 M16 130 50 HBNM16x140 M16 140 40 HBNM16x150 M16 150 40 HBNM20x35 M20 35 50 HBNM20x40 M20 40 50 HBNM20x45 M20 45 50 HBNM20x50 M20 50 50 HBNM20x55 M20 55 50 HBNM20x60 M20 60 50 HBNM20x65 M20 65 50 HBNM20x70 M20 70 50 HBNM20x75 M20 75 50 HBNM20x80 M20 80 50 HBNM20x85 M20 85 30 HBMM20x90 M20 90 30 HBNM20x100 M20 100 30 HBNM20x110 M20 110 30 HBNM20x120 M20 120 30 HBNM20x130 M20 130 30 HBNM20x140 M20 140 25 HBNM20x150 M20 150 25 HBNM20x170 M20 170 25 HBNM24x60 M24 60 25 HBNM24x65 M24 65 25 HBNM24x70 M24 70 25 HBNM24x80 M24 80 25 HBNM24x85 M24 85 25 HBNM24x90 M24 90 25 HBNM24x100 M24 100 25 FINISH: ZINC, GALVANISED OR STAINLESS 44
CUP HEAD BOLTS AND NUTS PART NO. BOLT DIA. LENGTH BOX QTY CBNM6x25 M6 25 200 CBNM6x40 M6 40 200 CBNM6x50 M6 50 200 CBNM6x65 M6 65 150 CBNM6x75 M6 75 150 CBNM6x90 M6 90 150 CBNM6x100 M6 100 150 CBNM8x20 M8 20 200 CBNM8x25 M8 25 200 CBNM8x30 M8 30 200 CBNM8x40 M8 40 200 CBNM8x50 M8 50 150 CBNM8x65 M8 65 150 CBNM8x75 M8 75 100 CBNM8x90 M8 90 100 CBNM8x120 M8 120 100 CBNM8x130 M8 130 100 CBNM8x140 M8 140 100 CBNM8x150 M8 150 100 PART NO. BOLT DIA. LENGTH BOX QTY CBNM12x30 M12 30 200 CBNM12x40 M12 40 200 CBNM12x45 M12 45 200 CBNM12x50 M12 50 150 CBNM12x60 M12 60 150 CBNM12x75 M12 75 150 CBNM12x90 M12 90 100 CBNM12x100 M12 100 100 CBNM12x120 M12 120 100 CBNM12x130 M12 130 75 CBNM12x140 M12 140 75 CBNM12x150 M12 150 75 CBNM12x170 M12 170 75 CBNM12x180 M12 180 75 CBNM12x200 M12 200 75 CBNM12x260 M12 260 50 CBNM12x300 M12 300 50 CBNM10x20 M10 20 200 CBNM10x25 M10 25 200 CBNM10x30 M10 30 200 CBNM10x40 M10 40 150 CBNM10x50 M10 50 100 CBNM10x65 M10 65 100 CBNM10x75 M10 75 100 CBNM10x90 M10 90 50 CBNM10x120 M10 120 50 CBNM10x130 M10 130 50 CBNM10x140 M10 140 50 CBNM10x150 M10 150 50 CBNM10x170 M10 170 100 CBNM10x180 M10 180 100 CBNM10x200 M10 200 100 FINISH: ZINC, GALVANISED OR STAINLESS 45
SET SCREWS SET SCREWS PART NO. SIZE BOX QTY HHSSM6X20 M6X20 100 HHSSM6X25 M6X25 100 HHSSM6X30 M6X30 100 HHSSM6X40 M6X40 100 HHSSM6X50 M6X50 100 HHSSM8X20 M8X20 100 HHSSM8X25 M8X25 100 HHSSM8X30 M8X30 100 HHSSM8X40 M8X40 100 HHSSM8X50 M8X50 100 HHSSM10X20 M10X20 100 HHSSM10X25 M10X25 100 HHSSM10X30 M10X30 100 HHSSM10X40 M10X40 100 HHSSM10X50 M10X50 100 HHSSM12X20 M12X20 100 HHSSM12X25 M12X25 100 HHSSM12X30 M12X30 100 HHSSM12X40 M12X40 100 HHSSM12X50 M12X50 100 HHSSM16X20 M16X20 100 HHSSM16X25 M16X25 100 HHSSM16X30 M16X30 100 HHSSM16X40 M16X40 100 HHSSM16X50 M16X50 100 FINISH: ZINC, GALVANISED OR STAINLESS NUTS HEX NUTS PART NO. SIZE BOX QTY HEXNUT-M06 M06 200 HEXNUT-M08 M08 200 HEXNUT-M10 M10 200 HEXNUT-M12 M12 200 WIZZ NUTS PART NO. SIZE BOX QTY WIZZ-M06 M06 200 WIZZ-M08 M08 200 WIZZ-M10 M10 200 WIZZ-M12 M12 200 FINISH: ZINC, GALVANISED OR STAINLESS 46
WASHERS COUPLERS ANCHORS FLAT WASHERS PART NO. SIZE BOX QTY FW-M6 M6 200 FW-M8 M8 200 FW-M10 M10 200 FW-M12 M12 200 MUDGUARD WASHERS PART NO. SIZE BOX QTY MW-M6 M6 200 MW-M8 M8 200 MW-M10 M10 200 MW-M12 M12 200 SPRING WASHERS PART NO. SIZE BOX QTY SW-M6 M6 200 SW-M8 M8 200 SW-M10 M10 200 SW-M12 M12 200 FINISH: ZINC, GALVANISED OR STAINLESS STEEL ROD COUPLERS PART NO. SIZE BOX QTY RC - M06 M06 200 RC - M08 M08 200 RC - M10 M10 100 RC - M12 M12 50 RC - M16 M16 50 RC - M20 M20 50 RC - M24 M24 25 HOBSON QUALITY FASTENER TYGABOLT PART NO. DESCRIPTION BOX QTY TYGA-M10X40 ZINC PLATED TYGA BOLT M10 X 40 50 TYGA-M10X50 ZINC PLATED TYGA BOLT M10 X 50 50 TYGA-M10X75 ZINC PLATED TYGA BOLT M10 X 75 50 TYGA-M10X100 ZINC PLATED TYGA BOLT M10 X 100 25 TYGA-M10X120 ZINC PLATED TYGA BOLT M10 X 120 25 TYGA-M12X60 ZINC PLATED TYGA BOLT M12 X 60 25 TYGA-M12X100 ZINC PLATED TYGA BOLT M12 X 100 20 TYGA-M12X120 ZINC PLATED TYGA BOLT M12 X 120 20 FINISH: ZINC GALVANISED AND STAINLESS STEEL FINISHES AVAILABLE ON REQUEST TM 47
ANCHORS HOBSON QUALITY FASTENER CLAWBOLT PART NO. DESCRIPTION BOX QTY CLAW-M6X85 CLAW BOLT M6 X 85 50 CLAW-M6X120 CLAW BOLT M6 X 120 50 CLAW-M8X80 CLAW BOLT M8 X 80 50 CLAW-M8X100 CLAW BOLT M8 X 100 50 CLAW-M8X120 CLAW BOLT M8 X 120 50 CLAW-M10X65 CLAW BOLT M10 X 65 25 CLAW-M10X75 CLAW BOLT M10 X 75 25 CLAW-M10X90 CLAW BOLT M10 X 90 25 CLAW-M10X120 CLAW BOLT M10 X 120 25 CLAW-M12X80 CLAW BOLT M12 X 80 20 CLAW-M12X100 CLAW BOLT M12 X 100 20 CLAW-M12X140 CLAW BOLT M12 X 140 20 CLAW-M12X180 CLAW BOLT M12 X 180 20 CLAW-M16X105 CLAW BOLT M16 X 105 20 CLAW-M16X125 CLAW BOLT M16 X 125 20 CLAW-M16X140 CLAW BOLT M16 X 140 20 CLAW-M16X190 CLAW BOLT M16 X 190 20 CLAW-M20X125 CLAW BOLT M20 X 125 20 CLAW-M20X160 CLAW BOLT M20 X 160 20 CLAW-M20X200 CLAW BOLT M20 X 200 20 FINISH: ZINC PLATED OR GALVANISED STAINLESS STEEL FINISH AVAILABLE ON REQUEST TM DROP IN ANCHOR PART NO. SIZE BOX QTY FM1820-M6 M6 x 25mm 100 FM1820-M8 M8 x 30mm 100 FM1820-M1030L M10 x 30mm LIPPED 50 FM1820-M1040 M10 x 40mm 50 FM1820-M1250 M12 x 50mm 50 FM1820-M16 M16 x 65mm 25 FINISH: ZINC DROP IN ANCHOR SETTING TOOL PART NO. SIZE FM1820-SET6 M6 FM1820-SET8 M8 FM1820-SET10 M10 FM1820-SET12 M12 FM1820-SET16 M16 48
ANCHORS PANTHA PLUG FINISH: ZINC PLATED BOX QTY:100 HOBSON QUALITY FASTENER PANTHA PLUG FINISH: NYLON BOX QTY:100 HOBSON QUALITY FASTENER NAIL IN ANCHOR NYLON ROUND HEAD PART NO. DESCRIPTION NYLON-RH5X25 NYLON NAIL ANCHOR 5 x 25 NYLON-RH5X40 NYLON NAIL ANCHOR 5 x 40 NYLON-RH6.5X25 NYLON NAIL ANCHOR 6.5 x 25 NYLON-RH6.5X40 NYLON NAIL ANCHOR 6.5 x 40 NYLON-RH6.5X50 NYLON NAIL ANCHOR 6.5 x 50 NAIL IN ANCHOR NYLON MUSHROOM HEAD PART NO. DESCRIPTION NYLON-MH5X25 NYLON NAIL ANCHOR 5 x 25 NYLON-MH6.5X40 NYLON NAIL ANCHOR 6.5 x 40 NAIL IN ANCHOR METAL PART NO. DESCRIPTION METALPIN-5X25 METAL NAIL ANCHOR 5 x 25 METALPIN-6.5X25 METAL NAIL ANCHOR 6.5 x 25 METALPIN-6.5X40 METAL NAIL ANCHOR 6.5 x 40 METALPIN-6.5X50 METAL NAIL ANCHOR 6.5 x 50 Drill a hole into the base material that suits the diameter and embedment depth of the Nylon Anchor that is being used (approx. 6mm deeper is required for Metal Anchor) Inset Pin Anchor through fixture and predilled hole Hammer screw pin into anchor to achieve expansion. Further adjustment available on Nylon Anchor by usign a flat screw driver. 49
DRILL BITS RIVETS TEKS RIVETS STEEL PART NO. DESCRIPTION RIVET-STEEL5-6 5-6 (5/32) RIVET-STEEL5-4 5-4 (5/32) RIVET-STEEL4-6 4-6 (1/8) RIVET-STEEL4-4 4-4 (1/8) RIVET-STEEL4-3 4-3 (1/8) BOX QTY : 1000 RIVETS ALUMINIUM PART NO. DESCRIPTION RIVET-ALUM5-6 5-6 (5/32) RIVET-ALUM5-4 5-4 (5/32) RIVET-ALUM4-6 4-6 (1/8) RIVET-ALUM4-4 4-4 (1/8) RIVET-ALUM4-3 4-3 (1/8) BOX QTY : 1000 METALTEKS PART NO. DESCRIPTION BOX QTY MTEK-10x16 10G x 16mm 1000 MTEK-10x25 10G x 25mm 1000 MTEK-12x25 12G x 25mm 1000 MTEK-10x16CL4 10G x 16mm 1000 MTEK-10x25CL4 10G x 25mm 1000 MTEK-12X20CL4 12G x 20mm 1000 MTEK-12X25CL4 12G x 25mm 1000 WOODTEKS CLASS 17 PART NO. DESCRIPTION BOX QTY WTEK-10X25 10G x 25mm 1000 WTEK-12X25 12G x 25mm 1000 WTEK-12X50 12G x 50mm 1000 FINISH: YELLOW ZINC CLASS 2 FINISH: YELLOW ZINC AND GAL CLASS 4 BUTTON HEAD METAL TEKS PART NO. DESCRIPTION BOX QTY MTEK-BH12 8-18 x 12 1000 MTEK-BH16 8-18 x 16 1000 DRIVE HEAD PHILLIPS HEAD FINISH: YELLOW ZINC CLASS 2 SERIES 500 SCREWS PART NO. DESCRIPTION BOX QTY SERIES500X32 12-24 x 32mm 1000 SERIES500X50 12-24 x 50mm 1000 SERIES500X65 12-24 x 65mm 1000 DRIVE HEAD 5 / 16 FINISH: GAL CLASS 4 PHILLIPS DRIVERS PART NO. DESCRIPTION DBIT-PH2-25 25 mm LONG DBIT-PH2-50 50 mm LONG DBIT-PH2-75 75 mm LONG DBIT-PH2-100 100 mm LONG DBIT-PH2-150 150 mm LONG NUT SETTERS PART NO. DESCRIPTION DBIT-NS 1/4-42 DBIT-NS 5/16-42 DBIT-NS 3/8-42 DBIT-NS 1/4-65 DBIT-NS 5/16-65 DBIT-NS 3/8-65 1/4 x 42mm LONG 5/16 x 42mm LONG 3/8 x 42mm LONG 1/4 x 65mm LONG 5/16 x 65mm LONG 3/8 x 65mm LONG 50
DRILLBITS PART NO. SIZE DBIT-1/4 1/4 DBIT-5/16 5/16 DBIT-M1 1 mm DBIT-M1.5 1.5 mm DBIT-M2 2 mm DBIT-M2.5 2.5 mm PART NO. DBIT-M3 DBIT-M4 DBIT-M4.5 DBIT-M5 DBIT-M5.5 DBIT-M6 STRAIGHT SHANK BIT HSS SIZE 3 mm 4 mm 4.5 mm 5 mm 5.5 mm 6 mm PART NO. DBIT-M6.5 DBIT-M7 DBIT-M7.5 DBIT-M8 DBIT-M8.5 DBIT-M9 DBIT-M9.5 SIZE 6.5 mm 7 mm 7.5 mm 8 mm 8.5 mm 9 mm 9.5 mm PART NO. DBIT-M10 DBIT-M10.5 DBIT-M11 DBIT-M11.5 DBIT-M12 DBIT-M12.5 DBIT-M13 SIZE 10 mm 10.5 mm 11 mm 11.5 mm 12 mm 12.5 mm 13 mm DRILL BIT DOUBLE END HSS PART NO. SIZE BOX QTY DBIT-DE11 #11 (3/16) 10 DBIT-DE20 #20 (5/32) 10 DBIT-DE30 #30 (1/8) 10 DRILL BIT SINGLE END HSS PART NO. SIZE BOX QTY DBIT-SE11 #11 (3/16) 10 DBIT-SE20 #20 (5/32) 10 DBIT-SE30 #30 (1/8) 10 DRILL BIT SDS MASONARY (4mm - 8mm) PART NO. SIZE DBIT-SDS4X160 4 X 160 DBIT-SDS5X110 5 X 110 DBIT-SDS5X160 5 X 160 DBIT-SDS5X210 5 X 210 DBIT-SDS5.5X110 5.5 X 110 DBIT-SDS5.5X160 5.5 X 160 DBIT-SDS6X160 6 X 160 DBIT-SDS6X210 6 X 210 DBIT-SDS6.5X110 6.5 X 110 DBIT-SDS6.5X160 6.5 X 160 DBIT-SDS7X160 7 X 160 DBIT-SDS8X110 8 X 110 DBIT-SDS8X160 8 X 160 DBIT-SDS8X210 8 X 210 DRILL BIT SDS MASONARY (10mm - 24mm) PART NO. SIZE DBIT-SDS10X160 10 X 160 DBIT-SDS10X210 10 X 210 DBIT-SDS10X260 10 X 260 DBIT-SDS12X160 12 X 160 DBIT-SDS12X210 12 X 210 DBIT-SDS12X250 12 X 250 DBIT-SDS12X260 12 X 260 DBIT-SDS13X150 13 X 150 DBIT-SDS15X150 15 X 150 DBIT-SDS16X200 16 X 200 DBIT-SDS18X200 18 X 200 DBIT-SDS20X250 20 X 250 DBIT-SDS24X250 24 X 250 DBIT-SDS25X250 25 X 250 51
ABRASIVES METAL CUT OFF BLADES PART NO. SIZE BOX QTY BLADE-MC100T 100 x 1.0 x 16 25 BLADE-MC115T 115 x 1.0 x 22 25 BLADE-MC125T 125 x 1.0 x 22 25 BLADE-MC230T 230 x 1.0 x 22 25 BLADE-MC100 100 x 2.5 x 16 25 BLADE-MC115 115 x 2.5 x 22 25 BLADE-MC125 125 x 2.5 x 22 25 BLADE-MC230 230 x 2.5 x 22 25 BLADE-MC350 350 x 3.0 x 25.4 L/SPD 10 BLADE-MC400 400 x 3.5 x 25.4 L/SPD 10 METAL GRINDING BLADES PART NO. SIZE BOX QTY BLADE-MG100 100 x 16 10 BLADE-MG115 115 x 22 10 BLADE-MG125 125 x 22 10 BLADE-MG230 230 x 22 10 HAND PADS PART NO. DESCRIPTION BOX QTY HANDPAD-COARSE HANDPAD COARSE 10 HANDPAD-MED HANDPAD MEDIUM 10 HANDPAD-VFINE HANDPAD VERY FINE 10 HANDPAD-UFINE HANDPAD ULTRA FINE 10 ABRASIVE MOP PART NO. SIZE BOX QTY ABMOP-40 30 x 15 x 6 40GRIT 10 ABMOP-60 30 x 15 x 6 60GRIT 10 ABMOP-80 30 x 15 x 6 80GRIT 10 ABMOP-120 30 x 15 x 6 120GRIT 10 FLAP DISC PART NO. SIZE BOX QTY FLAPDISC100-40 100 x 16 40 GRIT 10 FLAPDISC100-60 100 x 16 60 GRIT 10 FLAPDISC100-80 100 x 16 80 GRIT 10 FLAPDISC100-120 100 x 16 120 GRIT 10 FLAPDISC115-40 115 x 22 40 GRIT 10 FLAPDISC115-60 115 x 22 60 GRIT 10 FLAPDISC115-80 115 x 22 80 GRIT 10 FLAPDISC115-120 115 x 22 120 GRIT 10 FLAPDISC125-40 125 x 22 40 GRIT 10 FLAPDISC125-60 125 x 22 60 GRIT 10 FLAPDISC125-80 125 x 22 80 GRIT 10 FLAPDISC125-120 125 x 22 120 GRIT 10 52
HOLE SAWS PART NO. HOLESAW-14 HOLESAW-16 HOLESAW-17 HOLESAW-19 HOLESAW-20 HOLESAW-21 HOLESAW-22 HOLESAW-24 HOLESAW-25 HOLESAW-27 HOLESAW-29 HOLESAW-30 HOLESAW-32 HOLESAW-33 HOLESAW-35 HOLESAW-37 HOLESAW-38 HOLESAW-40 HOLESAW-41 HOLESAW-43 HOLESAW-44 HOLESAW-45 HOLESAW-46 HOLESAW-48 HOLESAW-50 HOLESAW-51 HOLESAW-52 HOLESAW-54 SIZE 14mm 16mm 17mm 19mm 20mm 21mm 22mm 24mm 25mm 27mm 29mm 30mm 32mm 33mm 35mm 37mm 38mm 40mm 41mm 43mm 44mm 45mm 46mm 48mm 50mm 51mm 52mm 54mm PART NO. HOLESAW-55 HOLESAW-57 HOLESAW-59 HOLESAW-60 HOLESAW-64 HOLESAW-67 HOLESAW-68 HOLESAW-70 HOLESAW-73 HOLESAW-75 HOLESAW-76 HOLESAW-79 HOLESAW-83 HOLESAW-86 HOLESAW-89 HOLESAW-92 HOLESAW-95 HOLESAW-98 HOLESAW-100 HOLESAW-102 HOLESAW-105 HOLESAW-108 HOLESAW-111 HOLESAW-114 HOLESAW-121 HOLESAW-127 HOLESAW-140 HOLESAW-146 HOLESAW-152 SIZE 55mm 57mm 59mm 60mm 64mm 67mm 68mm 70mm 73mm 75mm 76mm 79mm 83mm 86mm 89mm 92mm 95mm 98mm 100mm 102mm 105mm 108mm 111mm 114mm 121mm 127mm 140mm 146mm 152mm PART NO. ARBOR-1/4RND ARBOR-1/4UNIS ARBOR-1/4UNIL ARBOR-7/16HEXS ARBOR-3/8HEX ARBOR-7/16HEXL ARBOR-7/16Q ARBOR-3/8Q ARBOR5/8Q ARBOREXTN ARBORADP PILOT-1/4X3-1/2 PILOT-1/4X4-1/2 ARBOR DESCRIPTION 1/4 ROUND ARBOR TO SUIT 14-30mm 1/4 UNIVERSAL ARBOR TO SUIT 14-30mm 1/4 ROUND ARBOR TO SUIT 32-51mm 7/16 HEX ARBOR TO SUIT 14-30 mm 3/8 ROUND ARBOR TO SUIT 14-30mm 7/16 HEX ARBOR TO SUIT 32-51 mm 7/16 QUICK CHANGE ARBOR TO SUIT 32-152 mm 3/8 QUICK CHANGE ARBOR TO SUIT 32-152 mm 5/8 QUICK CHANGE ARBOR TO SUIT 32-152 mm 12 ARBOR EXTENSION ARBOR ADAPTER 1/4 ARBOR PILOT 3-1/2 LONG 1/4 ARBOR PILOT 4-1/2 LONG PART NO. CORE-30 CORE-SDSADP PILOT-CORE CORE BIT DESCRIPTION 30mm CORE BIT 170mm LONG MULTI SDS CORE BIT ADAPTER STRAIGHT SHANK CORE BIT PILOT 53
ACCESSORIES GROMMET PART NO DESCRIPTION BOX QTY GROM TO SUIT 15-25 TUBE 100 MSP METAL STUD PUNCH 34mm EA FLEXIDEXTITE PART NO. PIPE BASE BOX QTY FDT0-35 0-35 99 x 99 EA FDT5-55 5-55 137 x 137 EA FDT50-70 50-70 178 x 178 EA FDT5-120 5-120 218 x 218 EA FDT110-170 110-170 284 x 284 EA FDT160-220 160-220 365 x 365 EA FDT160-300 160-300 453 x 453 EA FDT290-400 290-400 581 x 581 EA SUITABLE FOR METAL ROOFING PART NO. HOOPIRON BLUE-STRAP HANGING STRAPS DESCRIPTION METAL HOOP IRON 25mm x 30mtr BLUE HANGING STRAP 25mm x 50mtr TAPES DUCTTAPE-GRY BOX QTY:60 DUCTTAPE-BLK BOX QTY:60 DUCTTAPE-FR SILVER FIRE RATED AS4254 DUCT TAPE FOILTAPE-48 REINFORCED FOIL TAPE 48mm x 50mtr DUCTFOAM-G18 DUCTFOAM-B12 DUCTFOAM 6.4 mm x 18 mm x 15 mtr BOX QTY : 24 5 mm x 12 mm x 15 mtr LINERLESS BOX QTY : 30 FOILTAPE-72 REINFORCED FOIL TAPE 72mm x 50mtr 54
ACCESSORIES CABLE TIES PART NO. SIZE BOX QTY CT-300 300 100 CT-530 530 100 CT-830 830 100 CT-1220 1220 100 CT-1550 1550 100 CT-TENS TENSIONER GUN 1 SILICONE PART NO. BOX QTY FLEXIDUCT 20 GAPFILLER 12 SLC-GUN 1 SPRAY PAINT PART NO. BOX QTY SP-SILVERZINC 24 SP-BLACK 12 SP-COLDGAL 24 SP-FLUROGREEN 12 SP-FLUROPINK 12 SP-FLUROORANGE 12 SP-FLUROYELLOW 12 ROOF AND GUTTER PART NO. BOX QTY SLC-RG-CLR 20 SLC-RG-GREY 20 SLC-RG-ALUM 20 KITCHEN AND BATHROOM PART NO. BOX QTY SLC-KB-CLR 20 SLC-KB-WHITE 20 EXPANDER FOAM PART NO. BOX QTY EXPFOAM 12 HACKSAW BLADES PART NO. TPI FOR CUTTING PACK QTY BLADE-H18T 18 COPPER 100 BLADE-H24T 24 MILD STEEL 100 BLADE-H32T 32 HARDENED STEEL 100 55
ACCESSORIES BUILDERS PENCIL MARKERS PART NO. BOX QTY MARKERS-BLACK 12 COLOURED RAGS PART NO. RAGS-COLOUR BOX QTY 10KG PIPE MARKERS WATER GREEN AND WHITE CHILLED WATER CHILLED WATER FLOW CHILLED WATER RETURN COLD WATER DOMESTIC COLD WATER DOMESTIC HOT WATER HEATING HOT WATER FLOW HEATING HOT WATER RETURN HOT WATER HOT WATER FLOW HOT WATER RETURN NON POTABLE WATER STORM WATER HEATING WATER HEAT HOT WATER CONDENSOR WATER FLOW CONDENSOR WATER RETURN CONDENSATE COOLING WATER MISCELLANEOUS BLACK / WHITE DRAINS SEWAGE TRADE WASTE VENT GREASE AIR LIGHT BLUE VACUUM GAS SAND AND BLACK NATURAL GAS KPA NATURAL GAS STEAM SILVER AND GREY STEAM PACK QTY:10 FIRE RED AND WHITE FIRE HOSE REEL FIRE HYDRANT FIRE SERVICE FIRE SPRINKLER FLOW AND RETURN R FL SIZES: MEDIUM 400mm x 27mm TO SUIT PIPE 45mm - 75mm LARGE 400mm x 50mm TO SUIT PIPE 75mm + 56
ZIP - CLIP Drill a 6mm hole to a minimum depth of 30mm Hammer in the fixing ZIP CLIP CON LOCK PART NO. LENGTH S.W.L ZIPCLG02 2 mt 10 kg ZIPCLG03 3 mt 10 kg ZIPCLG05 5 mt 10 kg ZIPCLG10 10 mt 10 kg ZIPCLS01 1 mt 50 kg ZIPCLS02 2 mt 50 kg ZIPCLS03 3 mt 50 kg ZIPCLS05 5 mt 50 kg ZIPCLS10 10 mt 50 kg ZIPCLY01 1 mt 120 kg ZIPCLY02 2 mt 120 kg ZIPCLY03 3 mt 120 kg ZIPCLY05 5 mt 120 kg ZIPCLY10 10 mt 120 kg Anchor is now fixed. No claw back required PACK QTY:10 ZIP CLIP ZIP LOCK PART NO. LENGTH S.W.L ZIPZLG01 1 mt 10 kg ZIPZLG02 2 mt 10 kg ZIPZLG03 3 mt 10 kg ZIPZLG05 5 mt 10 kg ZIPZLG10 10 mt 10 kg ZIPZLS01 1 mt 50 kg ZIPZLS02 2 mt 50 kg ZIPZLS03 3 mt 50 kg ZIPZLS05 5 mt 50 kg ZIPZLS10 10 mt 50 kg ZIPZLY01 1 mt 120 kg ZIPZLY02 2 mt 120 kg ZIPZLY03 3 mt 120 kg PACK QTY:10 57
ZIP - CLIP ZIP CLIP UNI LOCK PART NO. LENGTH S.W.L ZIPULG02 1 mt 10 kg ZIPULG02 2 mt 10 kg ZIPULG03 3 mt 10 kg ZIPULG05 5 mt 10 kg ZIPULG10 10 mt 10 kg ZIPULS01 1 mt 35 kg ZIPULS02 2 mt 35 kg ZIPULS03 3 mt 35 kg ZIPULS05 5 mt 35 kg ZIPULS10 10 mt 35 kg PACK QTY:10 - For timber applications pre-drill timber and use a screw to fix through the bracket. - For steel and concrete applications use self tapping fixing or a Gas nailer with a suitable nail. ZIP CLIP SHOT LOCK PART NO. LENGTH S.W.L ZIPSLG01 1 mt 10 kg ZIPSLG02 2 mt 10 kg ZIPSLG03 3 mt 10 kg ZIPSLG05 5 mt 10 kg ZIPSLG10 10 mt 10 kg ZIPSLS01 1 mt 35 kg ZIPSLS02 2 mt 35 kg ZIPSLS03 3 mt 35 kg ZIPSLS05 5 mt 35 kg ZIPSLS10 10 mt 35 kg PACK QTY:10 COMPATIBLE WITH FLEXISTRUT POWER DRIVE TOOL ZIP CLIP PURLIN HANGER PART NO. LENGTH S.W.L ZIPVLS01 1 mt 35 kg ZIPVLS02 2 mt 35 kg ZIPVLS03 3 mt 35 kg ZIPVLS05 5 mt 35 kg ZIPVLS10 10 mt 35 kg Pass the end fixing into decking profile and turn through 90 degrees. Screw the grub screw to the top of the decking profile. ZIP CLIP DEC LOCK PART NO. LENGTH S.W.L ZIPDLG01 1 mt 10 kg ZIPDLG02 2 mt 10 kg ZIPDLG03 3 mt 10 kg ZIPDLG05 5 mt 10 kg ZIPDLG10 10 mt 10 kg ZIPDLS01 1 mt 50 kg ZIPDLS02 2 mt 50 kg ZIPDLS03 3 mt 50 kg ZIPDLS05 5 mt 50 kg ZIPDLS10 10 mt 50 kg PACK QTY:10 PACK QTY:10 58
DRIVE PINS PART NO. FM510000 FLEXISTRUT POWER DRIVE TOOL DESCRIPTION.27 CAL LOW VEL. SEMI AUTO.27 CAL 10 LOAD STRIP PART NO. DESCRIPTION FM510222.27 CAL GREEN STRIP FM510223.27 CAL YELLOW STRIP FM510225.27 CAL RED STRIP BOX QTY : 100 8MM DRIVE PIN PART NO. LENGTH FM510167 16mm (knurled) FM510168 19mm (knurled) FM510155 19mm FM510156 22mm FM510157 27mm FM510158 32mm FM510159 37mm FM510160 42mm FM510162 52mm FM510064 62mm FM510065 72mm BOX QTY : 100 8MM DRIVE PIN CEILING CLIP PART NO. DESCRIPTION FM510191 90 DEGREE BRACKET 27mm PIN 8MM DRIVE PIN ROD HANGER PART NO. DESCRIPTION FMPA-M10 M10 ROD HANGER 8MM DRIVE PIN WASHERED PART NO. LENGTH WASHER FM510183 27mm 25mm FM510184 32mm 25mm BOX QTY : 100 8MM DRIVE PIN CABLE TIE PART NO. DESCRIPTION FM511002 CABLE TIE 240mm 27mm PIN FM511003 CABLE TIE 240mm 32mm PIN 59
NUT CLAMP AND FERRULE FOR STEEL PIPE FM109 PART NO. PIPE DIA. INS. FERRULE DIA. NUT FM109-015A 25 21 x 73 FM109-015B 15nb 38 21 x 102 M10 FM109-015C 50 21 x 127 FM109-020A 25 27 x 76 FM109-020B 20nb 38 27 x 102 M10 FM109-020C 50 27 x 127 FM109-025A 25 34 x 83 FM109-025B 25nb 38 34 x 115 M10 FM109-025C 50 34 x 140 FM109-032A 25 43 x 89 FM109-032B 32nb 38 43 x 115 M10 FM109-032C 50 43 x 140 FM109-040A 25 48 x 102 FM109-040B 40nb 38 48 x 127 M10 FM109-040C 50 48 x 152 FM109-050A 25 60 x 115 FM109-050B 50nb 38 60 x 140 M10 FM109-050C 50 60 x 165 PART NO. PIPE DIA. INS. FERRULE DIA. NUT FM109-065A 25 73 x 127 FM109-065B 65nb 38 73 x 152 M10 FM109-065C 50 73 x 178 FM109-080A 25 89 x 140 FM109-080B 80nb 38 89 x 165 M10 FM109-080C 50 89 x 190 FM109-100A 25 115 x 165 FM109-100B 100nb 38 115 x 190 M10 FM109-100C 50 115 x 220 FM109-125A 25 140 x 190 FM109-125B 125nb 38 140 x 220 M12 FM109-125C 50 140 x 240 FM109-150A 25 168 x 220 FM109-150B 150nb 38 168 x 240 M12 FM109-150C 50 168 x 268 FM109-200A 25 220 x 275 FM109-200B 200nb 38 220 x 300 M12 FM109-200C 50 220 x 324 FM109 - TIMBER FERRULE eg: FM109-015A FB109 - FLEXIBLOCK eg: FB109-015A FINISH: ZINC PLATED STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 60
FM110 NUT CLAMP AND FERRULE FOR COPPER PIPE PART NO. PIPE DIA. INS. FERRULE DIA. NUT FM110-015D 25 13 x 65 FM110-015E 15cu 38 13 x 89 M10 FM110-015F 50 13 x 115 FM110-020D 25 19 x 70 FM110-020E 20cu 38 19 x 102 M10 FM110-020F 50 19 x 127 FM110-025D 25 25 x 76 FM110-025E 25cu 38 25 x 102 M10 FM110-025F 50 25 x 127 FM110-032D 25 32 x 83 FM110-032E 32cu 38 32 x 115 M10 FM110-032F 50 32 x 140 FM110-040D 25 38 x 89 FM110-040E 40cu 38 38 x 115 M10 FM110-040F 50 38 x 140 FM110-050D 25 51 x 102 FM110-050E 50cu 38 51 x 127 M10 FM110-050F 50 51 x 152 PART NO. PIPE DIA. INS. FERRULE DIA. NUT FM110-065D 25 65 x 115 FM110-065E 65cu 38 65 x 140 M10 FM110-065F 50 65 x 165 FM110-080D 25 76 x 127 FM110-080E 80cu 38 76 x 152 M10 FM110-080F 50 76 x 178 FM110-100D 25 102 x 152 FM110-100E 100cu 38 102 x 178 M10 FM110-100F 50 102 x 203 FM110-125D 25 127 x 178 FM110-125E 125cu 38 127 x 203 M12 FM110-125F 50 127 x 228 FM110-150D 25 152 x 203 FM110-150E 150cu 38 152 x 228 M12 FM110-150F 50 152 x 252 FM110-200D 25 203 x 250 FM110-200E 200cu 38 203 x 275 M12 FM110-200F 50 203 x 300 FM110 - TIMBER FERRULE eg: FM110-015D FB110 - FLEXIBLOCK eg: FB110-015D FINISH: ZINC PLATED STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 61
STANDARD U BOLTS FM112 PART NO. PIPE DIA A W L T BOX QTY FM112-21 15nb M10 21 65 50 25 FM112-27 20nb M10 27 77 50 50 FM112-34 25nb M10 34 85 50 20 FM112-43 32nb M10 43 93 50 20 FM112-48 40nb M10 48 100 50 25 FM112-60 50nb M10 60 110 50 25 FM112-76 65nb M12 76 127 50 20 FM112-89 80nb M12 89 140 50 20 FM112-115 100nb M12 115 165 50 25 FM112-140 125nb M12 140 190 50 20 FM112-168 150nb M12 168 220 50 10 FM112-219 200nb M16 219 295 75 10 FM112-273 250nb M20 273 370 100 5 FM112-324 300nb M20 324 420 100 5 FM112-356 350nb M20 356 455 100 - FM112-406 400nb M20 406 505 100 - FM112-457 450nb M24 457 555 100 - FM112-508 500nb M24 508 605 100 - FM112-610 600nb M24 610 710 100 - FINISH: GALVANISED COMPLETE WITH TWO NUTS 62
DMPVC DMCU DM300 FM116 FM117 DOMESTIC PLUMBING PRODUCTS DWV PVC CLIPS PART NO. TO SUIT BOX QTY DMPVC-040 40mm P.V.C 20 DMPVC-050 50mm P.V.C 20 DMPVC-065 65mm P.V.C 20 DMPVC-080 80mm P.V.C 20 DMPVC-100 100mm P.V.C 20 DMPVC-150 150mm P.V..C 20 FINISH: POLY WHITE DWV PVC EXPANSION CLIPS PART NO. TO SUIT BOX QTY DMPVCEXP-040 40mm EXP P.V.C 20 DMPVCEXP-050 50mm EXP P.V.C 20 DMPVCEXP-065 65mm EXP P.V.C 20 DMPVCEXP-080 80mm EXP P.V.C 20 DMPVCEXP-100 100mm EXP P.V.C 20 FINISH: POLY GREY DM300LD HANGING STRAP FINISH: GALVABOND Bags of 50 COPPER CLIPS PART NO. TO SUIT BOX QTY DMCU-015 15 CU 20 DMCU-020 20 CU 20 DMCU-025 25 CU 20 DMCU-032 32 CU 20 DMCU-040 40 CU 20 DMCU-050 50 CU 20 DMCU-065 65 CU 20 DMCU-080 80 CU 20 DMCU-100 100 CU 20 DMCU-152 152 CU 20 FINISH: POLY BROWN FM116 STANDARD STAND-OFF BRACKET FINISH: ZINC PLATED Bags of 100 FM117 ADJUSTABLE STAND-OFF BRACKET FINISH: ZINC PLATED Bags of 100 63
DOMESTIC PLUMBING PRODUCTS DOMESTIC CLEVIS HANGER PART NO. TO SUIT BOX QTY DM-CLL M10 ROD 50 DM-CLS M10 ROD 50 DM-C DWV FMSO DM-153L DM-153S FINISH: ZINC USED IN RELATION WITH DOMESTIC WRAP AROUND CLIPS MATERIAL: 20x3 STAND OFF BRACKETS DWV P.V.C PART NO. TO SUIT BOX QTY DWV-SO-040 40mm P.V.C 50 DWV-SO-050 50mm P.V.C 50 DWV-SO-065 65mm P.V.C 50 DWV-SO-080 80mm P.V.C 50 DWV-SO-090 90mm P.V.C 50 DWV-SO-100 100mm P.V.C 20 FINISH: POLY WHITE MATERIAL: 20x1.3 SHORT SADDLES DWV P.V.C PART NO. TO SUIT BOX QTY DWV-SS-040 40mm P.V.C 50 DWV-SS-050 50mm P.V.C 50 DWV-SS-065 65mm P.V.C 50 DWV-SS-080 80mm P.V.C 50 DWV-SS-090 90mm P.V.C 50 DWV-SS-100 100mm P.V.C 20 FINISH: POLY WHITE MATERIAL: 20x1.3 STAND OFF BRACKETS DWV P.V.C PART NO. TO SUIT MATERIAL BOX QTY FMSO-040 40mm P.V.C 25x3 20 FMSO-050 50mm P.V.C 25x3 20 FMSO-065 65mm P.V.C 25x3 20 FMSO-080 80mm P.V.C 25x3 20 FMSO-090 90mm P.V.C 25x3 20 FMSO-100 100mm P.V.C 25x3 20 FMSO-150 150mm P.V.C 25x3 10 FMSO-250 250mm PV.C 40x6 2 (bag) FINISH: POLY WHITE 64
FM120 STANDARD DOUBLE BOLTED CLAMP FOR STEEL PIPE PART NO. PIPE DIA. D BOLT MATERIAL BOX QTY FM120-021 15nb 21 M6 x 25 20 x 3 50 FM120-027 20nb 27 M6 x 25 20 x 3 50 FM120-034 25nb 34 M6 x 25 20 x 3 50 FM120-043 32nb 43 M6 x 25 20 x 3 25 FM120-048 40nb 48 M6 x 25 20 x 3 25 FM120-060 50nb 60 M6 x 25 20 x 3 25 FM120-076 65nb 73 M6 x 25 20 x 3 25 FM120-089 80nb 89 M6 x 25 20 x 3 20 FM120-115 100nb 115 M6 x 25 25 x 3 20 FM120-140 125nb 140 M8 x 40 25 x 5 10 FM120-168 150nb 168 M12 x 45 40 x 6 5 FM120-220 200nb 220 M12 x 45 40 x 6 5 FM120-273 250nb 273 M16 x 50 50 x 6 - FM120-324 300nb 324 M20 x 75 50 x 10 - FM120-355 350nb 355 M20 x 75 65 x 10 - FM120-406 400nb 408 M24 x 90 75 x 10 - FM120-457 450nb 457 M24 x 90 75 x 12 - FM120-508 500nb 508 M24 x 90 75 x 16 - FM120-610 600nb 610 M24 x 90 75 x 16 - FINISH: GALVANISED AND PLAIN STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 65
STANDARD DOUBLE BOLTED CLAMP FOR COPPER PIPE FM121 PART NO. PIPE DIA. D BOLT MATERIAL BOX QTY FM121-015 15cu 12.7 M6 x 25 20 x 3 50 FM121-020 20cu 20 M6 x 25 20 x 3 50 FM121-025 25cu 25 M6 x 25 20 x 3 25 FM121-032 32cu 32 M6 x 25 20 x 3 25 FM121-040 40cu 40 M6 x 25 20 x 3 25 FM121-051 50cu 51 M6 x 25 20 x 3 25 FM121-064 65cu 64 M6 x 25 20 x 3 20 FM121-076 80cu 76 M6 x 25 20 x 3 25 FM121-100 100cu 102 M6 x 25 20 x 3 - FM121-125 127cu 127 M8 x 40 25 x 3 - FM121-150 150cu 152 M8 x 40 25 x 3 - FM121-200 200cu 204 M12 x 45 40 x 6 - FINISH: POLYESTER POWDER COATED STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 66
FM122 DOUBLE BOLTED CLAMP AND FERRULE FOR STEEL PIPE PART NO. PIPE DIA. INS. FERRULE DIA. FM122-015A 25 21 x 73 FM122-015B 15nb 38 21 x 102 FM122-015C 50 21 x 127 FM122-020A 25 27 x 76 FM122-020B 20nb 38 27 x 102 FM122-020C 50 27 x 127 FM122-025A 25 34 x 83 FM122-025B 25nb 38 34 x 115 FM122-025C 50 34 x 140 FM122-032A 25 43 x 89 FM122-032B 32nb 38 43 x 115 FM122-032C 50 43 x 140 FM122-040A 25 48 x 102 FM122-040B 40nb 38 48 x 127 FM122-040C 50 48 x 152 FM122-050A 25 60 x 115 FM122-050B 50nb 38 60 x 140 FM122-050C 50 60 x 165 FM122-065A 25 73 x 127 FM122-065B 65nb 38 73 x 152 FM122-065C 50 73 x 178 FM122-080A 25 89 x 140 FM122-080B 80nb 38 89 x 165 FM122-080C 50 89 x 190 FM122-100A 25 115 x 165 FM122-100B 100nb 38 115 x 190 FM122-100C 50 115 x 220 FM122 - TIMBER FERRULE eg: FM122-015A FB122 - FLEXIBLOCK eg: FB122-015A PART NO. PIPE DIA. INS. FERRULE DIA. FM122-125A 25 140 x 190 FM122-125B 125nb 38 140 x 220 FM122-125C 50 140 x 240 FM122-150A 25 168 x 220 FM122-150B 150nb 38 168 x 240 FM122-150C 50 168 x 268 FM122-200A 25 220 x 275 FM122-200B 200nb 38 220 x 300 FM122-200C 50 220 x 324 FM122-250A 25 273 x 324 FM122-250B 250nb 38 273 x 356 FM122-250C 50 273 x 375 FM122-300A 25 324 x 375 FM122-300B 300nb 38 324 x 406 FM122-300C 50 324 x 424 FM122-350A 25 355 x 406 FM122-350B 350nb 38 355 x 424 FM122-350C 50 355 x 457 FM122-400A 25 406 x 457 FM122-400B 400nb 38 406 x 483 FM122-400C 50 406 x 508 FM122-450A 25 455 x 508 FM122-450B 450nb 38 455 x 533 FM122-450C 50 455 x 557 FM122-500A 25 508 x 557 FM122-500B 500nb 38 508 x 584 FM122-500C 50 508 x 610 67 FINISH: GALVANISED & PLAIN STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS
DOUBLE BOLTED CLAMP AND FERRULE FOR COPPER PIPE FM123 PART NO. PIPE DIA. INS. FERRULE DIA. FM123-015D 25 13 x 65 FM123-015E 15cu 38 13 x 89 FM123-015F 50 13 x 115 FM123-020D 25 19 x 70 FM123-020E 20cu 38 19 x 102 FM123-020F 50 19 x 127 FM123-025D 25 25 x 76 FM123-025E 25cu 38 25 x 102 FM123-025F 50 25 x 127 FM123-032D 25 32 x 83 FM123-032E 32cu 38 32 x 115 FM123-032F 50 32 x 140 FM123-040D 25 38 x 89 FM123-040E 40cu 38 38 x 115 FM123-040F 50 38 x 140 FM123-050D 25 51 x 102 FM123-050E 50cu 38 51 x 127 FM123-050F 50 51 x 152 PART NO. PIPE DIA. INS. FERRULE DIA. FM123-065D 25 65 x 115 FM123-065E 65cu 38 65 x 140 FM123-065F 50 65 x 165 FM123-080D 25 76 x 127 FM123-080E 80cu 38 76 x 152 FM123-080F 50 76 x 178 FM123-100D 25 102 x 152 FM123-100E 100cu 38 102 x 178 FM123-100F 50 102 x 203 FM123-125D 25 127 x 178 FM123-125E 125cu 38 127 x 203 FM123-125F 50 127 x 228 FM123-150D 25 152 x 203 FM123-150E 150cu 38 152 x 228 FM123-150F 50 152 x 252 FM123-200D 25 203 x 252 FM123-200E 200cu 38 203 x 275 FM123-200F 50 203 x 300 FM123 - TIMBER FERRULE eg: FM123-015D FB123 - FLEXIBLOCK eg: FB123-015D FINISH: GALVANISED & PLAIN STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 68
FM125 STANDARD SADDLE CLAMP FOR STEEL PIPE H - HOLE Ø PART NO. PIPE DIA. D A B H MATERIAL BOX QTY FM125-021 15nb 21 85 61 9 25 x 3 100 FM125-027 20nb 27 91 67 9 25 x 3 50 FM125-034 25nb 34 98 74 9 25 x 3 50 FM125-043 32nb 43 107 83 9 25 x 3 50 FM125-048 40nb 48 112 88 9 25 x 3 50 FM125-060 50nb 60 124 100 9 25 x 3 50 FM125-076 65nb 76 140 116 9 25 x 3 25 FM125-089 80nb 89 153 129 9 25 x 3 20 FM125-115 100nb 115 178 154 9 25 x 3 25 FM125-140 125nb 140 204 180 9 25 x 3 25 FM125-168 150nb 168 280 240 14 40 x 6 20 FM125-220 200nb 220 332 292 14 40 x 6 - FM125-273 250nb 273 405 345 18 50 x 6 - FM125-324 300nb 324 484 424 22 50 x 10 - FM125-355 350nb 355 515 455 22 65 x 10 - FM125-408 400nb 408 568 508 26 75 x 10 - FM125-457 450nb 457 607 547 26 75 x 12 - FINISH: GALVANISED & PLAIN STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 69
STANDARD SADDLE CLAMP FOR COPPER CLAMP FM126 H - HOLE Ø PART NO. PIPE DIA. D A B H MATERIAL FM126-015 15cu 12.7 78 48 9 25 x 3 FM126-020 20cu 20 83 59 9 25 x 3 FM126-025 25cu 25 89 65 9 25 x 3 FM126-032 32cu 32 96 72 9 25 x 3 FM126-038 40cu 38 102 78 9 25 x 3 FM126-051 50cu 51 115 91 9 25 x 3 FM126-064 65cu 64 128 104 9 25 x 3 FM126-076 80cu 76 140 116 9 25 x 3 FM126-102 100cu 102 166 142 9 25 x 3 FM126-127 125cu 127 191 167 9 25 x 3 FM126-152 150cu 152 248 208 14 40 x 6 FM126-203 200cu 204 299 259 14 40 x 6 NOTE: USE FM133A BARRIER STRIP WHEN BOLTED TO FLEXISTRUT CHANNEL FINISH: POLYESTER POWDER COATED STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 70
FM127 STANDARD BAND CLAMP FOR STEEL PIPE PART NO. PIPE DIA. D MATERIAL BOLT & NUT BOX QTY FM127-021 15nb 21 25 x 1.0 M6 x 25 100 FM127-027 20nb 27 25 x 1.0 M6 x 25 100 FM127-034 25nb 34 25 x 1.0 M6 x 25 100 FM127-043 32nb 43 25 x 1.2 M6 x 25 50 FM127-048 40nb 48 25 x 1.2 M8 x 25 50 FM127-060 50nb 60 25 x 1.2 M8 x 25 50 FM127-076 65nb 76 25 x 1.2 M8 x 25 50 FM127-089 80nb 89 32 x 1.6 M8 x 25 50 FM127-115 100nb 115 32 x 1.6 M8 x 25 25 FM127-140 125nb 140 32 x 1.6 M10 x 25 25 FM127-168 150nb 168 40 x 3.0 M12 x 45 - FM127-220 200nb 220 50 x 3.0 M12 x 45 - FINISH: GALVABOND STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 71
STANDARD BAND CLAMP FOR COPPER PIPE FM128 PART NO. PIPE DIA. D MATERIAL BOLT & NUT BOX QTY FM128-015 15cu 12.7 25 x 1.0 M6 x 25 100 FM128-020 20cu 20 25 x 1.0 M6 x 25 100 FM128-025 25cu 25 25 x 1.0 M6 x 25 100 FM128-032 32cu 32 25 x 1.2 M6 x 25 100 FM128-038 40cu 40 25 x 1.2 M8 x 25 50 FM128-051 50cu 51 25 x 1.2 M8 x 25 50 FM128-064 65cu 64 25 x 1.2 M8 x 25 25 FM128-076 80cu 76 32 x 1.6 M8 x 25 25 FM128-102 100cu 102 32 x 1.6 M8 x 25 25 FM128-127 125cu 127 32 x 1.6 M10 x 25 - FM128-150 150cu 152 40 x 3.0 M12 x 45 - FM128-200 200cu 204 40 x 3.0 M12 x 45 - FINISH: POLYESTER POWDER COATED STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 72
FM129 BAND CLAMP AND FERRULE FOR STEEL PIPE PART NO. PIPE DIA. INS. FERRULE DIA. FM129-015A 25 21 x 73 FM129-015B 15nb 38 21 x 102 FM129-015C 50 21 x 127 FM129-020A 25 27 x 76 FM129-020B 20nb 38 27 x 102 FM129-020C 50 27 x 127 FM129-025A 25 34 x 83 FM129-025B 25nb 38 34 x 115 FM129-025C 50 34 x 140 FM129-032A 25 43 x 89 FM129-032B 32nb 38 43 x 115 FM129-032C 50 43 x 140 FM129-040A 25 48 x 102 FM129-040B 40nb 38 48 x 127 FM129-040C 50 48 x 152 FM129-050A 25 60 x 115 FM129-050B 50nb 38 60 x 140 FM129-050C 50 60 x 165 PART NO. PIPE DIA. INS. FERRULE DIA. FM129-065A 25 73 x 127 FM129-065B 65nb 38 73 x 152 FM129-065C 50 73 x 178 FM129-080A 25 89 x 140 FM129-080B 80nb 38 89 x 165 FM129-080C 50 89 x 190 FM129-100A 25 115 x 165 FM129-100B 100nb 38 115 x 190 FM129-100C 50 115 x 220 FM129-125A 25 140 x 190 FM129-125B 125nb 38 140 x 220 FM129-125C 50 140 x 240 FM129-150A 25 168 x 220 FM129-150B 150nb 38 168 x 240 FM129-150C 50 168 x 268 FM129-200A 25 220 x 275 FM129-200B 200nb 38 220 x 300 FM129-200C 50 220 x 324 FM129 - TIMBER FERRULE eg: FM129-015A FB129 - FLEXIBLOCK eg: FB129-015A 73 FINISH: GALVABOND STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS
BAND CLAMP AND FERRULE FOR COPPER PIPE FM130 PART NO. PIPE DIA. INS. FERRULE DIA. FM130-015D 25 13 x 65 FM130-015E 15cu 38 13 x 89 FM130-015F 50 13 x 115 FM130-020D 25 19 x 70 FM130-020E 20cu 38 19 x 102 FM130-020F 50 19 x 127 FM130-025D 25 25 x 76 FM130-025E 25cu 38 25 x 102 FM130-025F 50 25 x 127 FM130-032D 25 32 x 83 FM130-032E 32cu 38 32 x 115 FM130-032F 50 32 x 140 FM130-040D 25 38 x 89 FM130-040E 40cu 38 38 x 115 FM130-040F 50 38 x 140 FM130-050D 25 51 x 102 FM130-050E 50cu 38 51 x 127 FM130-050F 50 51 x 152 PART NO. PIPE DIA. INS. FERRULE DIA. FM130-065D 25 65 x 115 FM130-065E 65cu 38 65 x 140 FM130-065F 50 65 x 165 FM130-080D 25 76 x 127 FM130-080E 80cu 38 76 x 152 FM130-080F 50 76 x 178 FM130-100D 25 102 x 152 FM130-100E 100cu 38 102 x 178 FM130-100F 50 102 x 203 FM130-125D 25 127 x 178 FM130-125E 125cu 38 127 x 203 FM130-125F 50 127 x 228 FM130-150D 25 152 x 203 FM130-150E 150cu 38 152 x 228 FM130-150F 50 152 x 252 FM130-200D 25 203 x 252 FM130-200E 200cu 38 203 x 275 FM130-200F 50 203 x 300 FM130 - TIMBER FERRULE eg: FM130-015D FB130 - FLEXIBLOCK eg: FB130-015D FINISH: GALVABOND STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 74
FM132FC FAST CLIP FAST CLIP PART NO. PIPE SIZE COLOUR BOX QTY FM132FC-3/8 10mm BLACK 100 FM132FC-1/2 13mm BLACK 100 FM132FC-5/8 16mm BLACK 50 FM132FC-3/4 20mm BLACK 50 FM132FC-7/8 22mm BLACK 50 FM132FC-1/18 28mm BLACK 50 FINISH: BLACK PLASTIC - NON METALLIC EASY INSTALLATION OF REFRIGERATION PIPE SYSTEM. SUITABLE FOR ALL FLEXISTRUT CHANNELS. 75
TWO PIECE CHANNEL CLIP FM132 PART NO. PIPE SIZE MATERIAL BOX QTY FM132-8 8cu 32x1.6 200 FM132-10 10cu 32x1.6 200 FM132-12.7 15cu 32x1.6 100 FM132-17 17cu 32x1.6 100 FM132-20 20cu 32x1.6 100 FM132-21 15nb 32x1.6 100 FM132-25 25cu 32x1.6 100 FM132-27 20nb 32x1.6 100 FM132-29 29ns 32x2.0 100 FM132-32 32cu 32x2.0 100 FM132-34 25nb 32x2.0 100 FM132-38 40cu 32x2.0 100 FM132-43 32nb 32x2.0 100 FM132-48 40nb 32x2.0 100 FM132-51 50cu 32x2.5 50 FM132-54 54ns 32x2.5 50 FM132-57 57ns 32x2.5 50 FM132-60 50nb 32x2.5 50 FM132-64 65cu 32x2.5 50 FM132-67 67ns 32x2.5 50 FM132-70 70ns 32x2.5 50 FM132-73 65nb/ SCHED 40 32x2.5 50 FM132-76 65nb/80cu 32x2.5 50 FM132-79 79ns 32x2.5 50 FM132-83 83ns 32x2.5 50 FM132-86 86ns 32x2.5 50 FM132-89 80nb 32x2.5 50 FM132-92 92ns 32x2.5 50 FM132-95 95ns 32x2.5 50 FM132-98 98ns 32x2.5 50 FM132-102 102cu 32x2.5 25 FM132-105 105ns 32x2.5 25 FM132-108 108ns 32x2.5 25 FM132-110 110ns 32x2.5 25 FM132-115 100nb 32x2.5 25 FM132-117 117ns 32x2.5 25 FM132-121 121ns 32x2.5 25 FM132-127 125cu 32x2.5 25 FM132-133 133ns 32x2.5 25 FM132-140 125nb 32x2.5 25 FM132-146 146ns 32x2.5 25 FM132-152 152cu 32x2.5 25 FM132-159 159ns 32x2.5 25 FM132-165 150nb 32x2.5 25 FM132-168 150nb/ SCHED 40 32x2.5 25 FM132-171 171ns 32x2.5 25 FM132-178 178ns 32x2.5 25 FM132-190 190ns 32x2.5 25 FM132-203 200cu 32x2.5 20 FM132-220 200nb 32x2.5 20 FM132-228 228ns 32x2.5 20 FM132-240 240ns 32x2.5 20 FM132-252 252cu 32x2.5 20 FM132-268 268ns 32x2.5 20 FM132-275 250nb 32x2.5 20 FM132-302 300cu 32x2.5 20 FM132-315 315ns 32x2.5 20 FM132-324 300nb 32x2.5 20 FINISH: ZINC PLATED AND GALVABOND (OTHER FINISHES AVAILABLE ON REQUEST) STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 76
FM132R TWO PIECE CHANNEL CLIP FOR COPPER PIPE FM132R TWO PIECE CHANNEL CLIP FOR REFRIGERATION PIPE PART NO. PIPE SIZE BOX QTY FM132R-1/4 6mm 50 FM132R-3/8 10mm 50 FM132R-1/2 13mm 50 FM132R-5/8 16mm 50 FM132R-3/4 20mm 25 FM132R-7/8 22mm 25 FM132R-1 25mm 25 FM132R-1 1/8 28mm 25 FM132R-1 1/4 32mm 25 FM132R-1 3/8 35mm 25 FM132R-1 5/8 41mm 20 FM132R-1 7/8 48mm 25 FM132R-2 1/8 54mm 25 FM132R-2 5/8 67mm 20 FM132R-3 1/8 79mm 10 FM132R-4 1/8 105mm 10 FINISH: ZINC PLATED FEATURES: 1. Suitable for refrigeration pipework. 2. Plastic inserts are designed to withstand temperatures between -30C to 125C 3. Self locking nut 4. Insulates against heat loss and reduces vibration 77
TWO PIECE CHANNEL CLIP FOR COPPER PIPE FM133 FM133A FM133 TWO PIECE CHANNEL CLIP FOR COPPER PIPE PART NO. PIPE SIZE BOX QTY FM133-015 15cu 100 FM133-020 20cu 100 FM133-025 25cu 100 FM133-032 32cu 100 FM133-038 40cu 100 FM133-051 50cu 25 FM133-064 65cu 25 FM133-076 80cu 25 FM133-102 100cu 25 FM133-127 125cu 25 FM133-152 150cu 25 FM133-203 200cu 25 FM133-252 250cu 25 FM133-302 300cu 20 FINISH: POLYESTER POWDER COATED FM133A BARRIER STRIP Polyester Powder Coated Continuous Snap Off strip used in conjunction with FM133 two piece clip - Prevents contact between copper pipe and galvanised channel. NOTE: FM133 INCLUDES FM133A UNLESS OTHERWISE REQUESTED. 78
FM134 TWO PIECE CHANNEL CLIP AND FERRULE FOR STEEL PIPE PART NO. PIPE DIA. INS. FERRULE DIA. FM134-015A 25 21 x 73 FM134-015B 15nb 38 21 x 102 FM134-015C 50 21 x 127 FM134-020A 25 27 x 76 FM134-020B 20nb 38 27 x 102 FM134-020C 50 27 x 127 FM134-025A 25 34 x 83 FM134-025B 25nb 38 34 x 115 FM134-025C 50 34 x 140 FM134-032A 25 43 x 89 FM134-032B 32nb 38 43 x 115 FM134-032C 50 43 x 140 FM134-040A 25 48 x 102 FM134-040B 40nb 38 48 x 127 FM134-040C 50 48 x 152 FM134-050A 25 60 x 115 FM134-050B 50nb 38 60 x 140 FM134-050C 50 60 x 165 FM134 - TIMBER FERRULE eg: FM134-015A FB134 - FLEXIBLOCK eg: FB134-015A FINISH: GALVABOND PART NO. PIPE DIA. INS. FERRULE DIA. FM134-065A 25 73 x 127 FM134-065B 65nb 38 73 x 152 FM134-065C 50 73 x 178 FM134-080A 25 89 x 140 FM134-080B 80nb 38 89 x 165 FM134-080C 50 89 x 190 FM134-100A 25 115 x 165 FM134-100B 100nb 38 115 x 190 FM134-100C 50 115 x 220 FM134-125A 25 140 x 190 FM134-125B 125nb 38 140 x 220 FM134-125C 50 140 x 240 FM134-150A 25 168 x 220 FM134-150B 150nb 38 168 x 240 FM134-150C 50 168 x 268 FM134-200A 25 220 x 275 FM134-200B 200nb 38 220 x 300 FM134-200C 50 220 x 324 STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 79
TWO PIECE CHANNEL CLIP AND FERRULE FOR COPPER PIPE FM135 PART NO. PIPE DIA. INS. FERRULE DIA. FM135-015D 25 13 x 65 FM135-015E 15cu 38 13 x 89 FM135-015F 50 13 x 115 FM135-020D 25 19 x 70 FM135-020E 20cu 38 19 x 102 FM135-020F 50 19 x 127 FM135-025D 25 25 x 76 FM135-025E 25cu 38 25 x 102 FM135-025F 50 25 x 127 FM135-032D 25 32 x 83 FM135-032E 32cu 38 32 x 115 FM135-032F 50 32 x 140 FM135-040D 25 38 x 89 FM135-040E 40cu 38 38 x 115 FM135-040F 50 38 x 140 FM135-050D 25 51 x 102 FM135-050E 50cu 38 51 x 127 FM135-050F 50 51 x 152 PART NO. PIPE DIA. INS. FERRULE DIA. FM135-065D 25 65 x 115 FM135-065E 65cu 38 65 x 140 FM135-065F 50 65 x 165 FM135-080D 25 76 x 127 FM135-080E 80cu 38 76 x 152 FM135-080F 50 76 x 178 FM135-100D 25 102 x 152 FM135-100E 100cu 38 102 x 178 FM135-100F 50 102 x 203 FM135-125D 25 127 x 178 FM135-125E 125cu 38 127 x 203 FM135-125F 50 127 x 228 FM135-150D 25 152 x 203 FM135-150E 150cu 38 152 x 228 FM135-150F 50 152 x 252 FM135-200D 25 203 x 252 FM135-200E 200cu 38 203 x 275 FM135-200F 50 203 x 300 FM135 - TIMBER FERRULE eg: FM135-015D FB135 - FLEXIBLOCK eg: FB135-015D FINISH: GALVABOND STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 80
FM136 TIMBER FERRULE MATERIAL F7 GRADE STRUCTURAL PLYWOOD STANDARD WIDTHS 40mm, 50mm, 80mm, 100mm (OTHER WIDTHS AVAILABLE ON REQUEST) ORDER: I.D. x O.D. x WIDTH eg: FM136 127x203x40 STANDARD TIMBER FERRULE SIZES FOR COPPER PIPE PIPE SIZE 25mm INSULATION 38mm INSULATION 50mm INSULATION ID x OD ID x OD ID x OD 15cu 12.7 x 64mm 12.7 x 89mm 12.7 x 114mm 20cu 19.0 x 70mm 19.0 x 102mm 19.0 x 127mm 25cu 25.4 x 76mm 25.4 x 102mm 25.4 x 127mm 32cu 31.8 x 83mm 31.8 x 114mm 31.8 x 140mm 40cu 38.1 x 89mm 38.1 x 114mm 38.1 x 140mm 50cu 51.2 x 102mm 51.2 x 127mm 51.2 x 152mm 65cu 63.5 x 114mm 63.5 x 140mm 63.5 x 165mm 80cu 76.2 x 127mm 76.2 x 152mm 76.2 x 178mm 100cu 101.6 x 152mm 101.6 x 178mm 101.6 x 203mm 125cu 127.0 x 178mm 127.0 x 203mm 127.0 x 228mm 150cu 152.4 x 203mm 152.4 x 228mm 152.4 x 252mm 200cu 203.2 x 252mm 203.2 x 275mm 203.2 x 302mm 250cu 254.0 x 300mm 254.0 x 324mm 254.0 x 355mm STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 81
TIMBER FERRULE FM136 STANDARD TIMBER FERRULE SIZES FOR STEEL PIPE PIPE SIZE 25mm INSULATION 38mm INSULATION 50mm INSULATION ID x OD ID x OD ID x OD 15nb 21.3 x 73mm 21.3 x 102mm 21.3 x 127mm 20nb 26.7 x 76mm 26.7 x 102mm 26.7 x 127mm 25nb 33.4 x 83mm 33.4 x 115mm 33.4 x 140mm 32nb 42.2 x 89mm 42.2 x 115mm 42.2 x 140mm 40nb 48.3 x 102mm 48.3 x 127mm 48.3 x 152mm 50nb 60.3 x 115mm 60.3 x 140mm 60.3 x 165mm 65nb 73 x 127mm 73 x 152mm 73 x 178mm 80nb 88.9 x 140mm 88.9 x 165mm 88.9 x 190mm 100nb 114.3 x 165mm 114.3 x 190mm 114.3 x 220mm 125nb 141.3 x 190mm 141.3 x 220mm 141.3 x 240mm 150nb 165.1 x 220mm 165.1 x 240mm 165.1 x 268mm 150nb (sched 40) 168.3 x 220mm 168.3 x 240mm 168.3 x 268mm 200nb 219.1 x 275mm 219.1 x 302mm 219.1 x 324mm 250nb 273.0 x 324mm 273.0 x 356mm 273.0 x 375mm 300nb 324.0 x 375mm 324.0 x 406mm 324.0 x 424mm 350nb 355.6 x 406mm 355.6 x 424mm 355.6 x 457mm 400nb 406.4 x 457mm 406.4 x 483mm 406.4 x 508mm 450nb 457.0 x 508mm 457.0 x 533mm 457.0 x 557mm 500nb 508.0 x 557mm 508.0 x 584mm 508.0 x 610mm 600nb 609.6 x 660mm 609.6 x 685mm 609.6 x 710mm STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 82
FB136 FLEXI BLOCK ID OD 50mm 50mm STANDARD FLEXI BLOCK FERRULE SIZES FOR COPPER PIPE PIPE SIZE 25mm INSULATION 38mm INSULATION 50mm INSULATION ID x OD ID x OD ID x OD 15cu 12.7 x 64mm 12.7 x 89mm 12.7 x 114mm 20cu 19.0 x 70mm 19.0 x 100mm 19.0 x 127mm 25cu 25.4 x 76mm 25.4 x 102mm 25.4 x 127mm 32cu 31.8 x 83mm 31.8 x 114mm 31.8 x 140mm 40cu 38.1 x 89mm 38.1 x 114mm 38.1 x 140mm 50cu 51.2 x 102mm 51.2 x 127mm 51.2 x 152mm 65cu 63.5 x 114mm 63.5 x 140mm 63.5 x 165mm 80cu 76.2 x 126mm 76.2 x 152mm 76.2 x 178mm 100cu 101.6 x 152mm 101.6 x 178mm 101.6 x 203mm 125cu 127.0 x 177mm 127.0 x 203mm 127.0 x 228mm 150cu 152.4 x 203mm 152.4 x 228mm 152.4 x 252mm 200cu 203.2 x 252mm 203.2 x 275mm 203.2 x 302mm 83 MATERIAL: CROSSLINKED CLOSED CELL PE FOAM DENSITY: 300 kg/m 2 MOISTURE ABSORPTION: <1% (BY WEIGHT, ROOM TEMP, 5HRS) TENSILE STRENGTH: 2.4 kg/m 2 TEAR STRENGTH: 8.3 kg/m 2 THERMAL CONDUCTIVITY 0.065 W/mK (ISO8302-1991) CONSTANT WORKING TEMP -40 o C TO 105 o C COMPRESSIVE STRENGTH 3.4 kg/cm 2 JIS 6767 COMES BOUND WITH FIRE RATED SILVER SISAL STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS
FLEXI BLOCK FB136 STANDARD FLEXI BLOCK FERRULE SIZES FOR STEEL PIPE PIPE SIZE 25mm INSULATION 38mm INSULATION 50mm INSULATION ID x OD ID x OD ID x OD 15nb 21.3 x 73mm 21.3 x 102mm 21.3 x 127mm 20nb 26.7 x 76mm 26.7 x 102mm 26.7 x 127mm 25nb 33.4 x 83mm 33.4 x 115mm 33.4 x 140mm 32nb 42.2 x 89mm 42.2 x 115mm 42.2 x 140mm 40nb 48.3 x 102mm 48.3 x 127mm 48.3 x 152mm 50nb 60.3 x 115mm 60.3 x 140mm 60.3 x 165mm 65nb 73 x 127mm 73 x 152mm 73 x 178mm 80nb 88.9 x 140mm 88.9 x 165mm 88.9 x 190mm 100nb 114.3 x 165mm 114.3 x 190mm 114.3 x 220mm 125nb 141.3 x 190mm 141.3 x 220mm 141.3 x 240mm 150nb 165.1 x 220mm 165.1 x 240mm 165.1 x 268mm 150nb (sched 40) 168.3 x 220mm 168.3 x 240mm 168.3 x 268mm 200nb 219.1 x 275mm 219.1 x 302mm 219.1 x 324mm 250nb 273.0 x 324mm 273.0 x 356mm 273.0 x 375mm COMES BOUND WITH FIRE RATED SILVER SISAL STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 13mm 19mm 63mm 75mm 100mm INSULATIONS 84
PU136 POLYURETHANE BLOCKS ORDER: I.D. x O.D. eg: PU 102x178 PIPE SIZE 20mm INS 25mm INS 38mm INS 50mm INS ID x OD ID x OD ID x OD ID x OD 15cu 13 x 53mm 13 x 63mm - - 20cu 19 x 59mm 19 x 69mm 19 x 102mm 19 x 127mm 25cu 25 x 65mm 25 x 76mm 25 x 102mm 25 x 127mm 32cu 32 x 72mm 32 x 82mm 32 x 108mm 32 x 132mm 40cu 38 x 78mm 38 x 88mm 38 x 114mm 38 x 138mm 50cu 51 x 91mm 51 x 102mm 51 x 127mm 51 x 151mm 65cu 64 x 104mm 64 x 114mm 64 x 140mm 64 x 165mm 80cu 76 x 116mm 76 x 126mm 76 x 152mm 76 x 176mm 100cu 102 x 142mm 102 x 152mm 102 x 178mm 102 x 202mm 125cu - - - 127 x 227mm 150cu - - - 152 x 252mm STANDARD LENGTH 1.2MTS STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST 85
ONE PIECE CHANNEL CLIP FM138 FM139 FM138 ONE PIECE CHANNEL CLIP FOR STEEL PIPE PART NO. PIPE SIZE BOLT SIZE BOX QTY FM138-021 15nb 6 mm 50 FM138-027 20nb 6 mm 50 FM138-034 25nb 6 mm 50 FM138-043 32nb 6 mm 50 FM138-048 40nb 6 mm 25 FM138-060 50nb 8 mm 25 FM138-073 65nb 8 mm 20 FM138-089 80nb 8 mm 20 FM138-115 100nb 8 mm 20 FM138-140 125nb 8 mm 20 FM138-168 150nb 8 mm 20 FINISH: GALVABOND NOTE: BOLT & CHANNEL NUT SUPPLIED SEPARATELY FM139 ONE PIECE CHANNEL CLIP FOR COPPER PIPE PART NO. PIPE SIZE BOLT SIZE FM139-015 15cu 6 mm FM139-020 20cu 6 mm FM139-025 25cu 6 mm FM139-032 32cu 6 mm FM139-038 40cu 6 mm FM139-051 50cu 8 mm FM139-064 65cu 8 mm FM139-076 80cu 8 mm FM139-102 100cu 8 mm FM139-127 125cu 8 mm FM139-152 150cu 8 mm FINISH: POLYESTER POWDER COATED NOTE: FM139 IS SUPPLIED WITH FM133A UNLESS REQUESTED OTHERWISE 86
LIGHT DUTY SLIDE GUIDE FM140 FM140 LIGHT DUTY SLIDE GUIDE FOR STEEL PIPE PART NO. PIPE SIZE A FM140-021 15nb 54 FM140-027 20nb 57 FM140-034 25nb 60 FM140-043 32nb 65 FM140-048 40nb 67 FM140-060 50nb 73 FM140-073 65nb 81 FM140-089 80nb 88 FM140-115 100nb 101 FM140-140 125nb 155 FM140-168 150nb 129 FINISH: GALVANISED FM140 LIGHT DUTY SLIDE GUIDE FOR COPPER PIPE PART NO. PIPE SIZE A FM140-015 15cu 49 FM140-020 20cu 53 FM140-025 25cu 56 FM140-032 32cu 59 FM140-038 40cu 62 FM140-051 50cu 73 FM140-064 65cu 76 FM140-076 80cu 81 FM140-102 100cu 94 FM140-127 125cu 108 FM140-152 150cu 121 FINISH: POLYESTER POWDER COATED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 87
LIGHT DUTY SLIDE GUIDE AND TIMBER FERRULE FOR STEEL PIPE FM141 PART NO. PIPE DIA. INS. FERRULE DIA. A FM141-015A 25 21 x 73 80 FM141-015B 15nb 38 21 x 102 94 FM141-015C 50 21 x 127 109 FM141-020A 25 27 x 76 80 FM141-020B 20nb 38 27 x 102 94 FM141-020C 50 27 x 127 109 FM141-025A 25 34 x 83 85 FM141-025B 25nb 38 34 x 115 101 FM141-025C 50 34 x 140 115 FM141-032A 25 43 x 89 88 FM141-032B 32nb 38 43 x 115 101 FM141-032C 50 43 x 140 115 FM141-040A 25 48 x 102 94 FM141-040B 40nb 38 48 x 127 109 FM141-040C 50 48 x 152 121 PART NO. PIPE DIA. INS. FERRULE DIA. A FM141-050A 25 60 x 115 101 FM141-050B 50nb 38 60 x 140 115 FM141-050C 50 60 x 165 128 FM141-065A 25 73 x 127 109 FM141-065B 65nb 38 73 x 152 121 FM141-065C 50 73 x 178 134 FM141-080A 25 89 x 140 115 FM141-080B 80nb 38 89 x 165 128 FM141-080C 50 89 x 190 140 FM141-100A 25 115 x 165 128 FM141-100B 100nb 38 115 x 190 140 FM141-100C 50 115 x 220 155 FINISH: GALVANISED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 88
FM141 LIGHT DUTY SLIDE GUIDE AND FERRULE FOR COPPER PIPE PART NO. PIPE DIA. INS. FERRULE DIA. A FM141-015D 25 13 x 65 76 FM141-015E 15cu 38 13 x 89 88 FM141-015F 50 13 x 115 101 FM141-020D 25 19 x 70 78 FM141-020E 20cu 38 19 x 102 94 FM141-020F 50 19 x 127 109 FM141-025D 25 25 x 76 80 FM141-025E 25cu 38 25 x 102 94 FM141-025F 50 25 x 127 109 FM141-032D 25 32 x 83 85 FM141-032E 32cu 38 32 x 115 101 FM141-032F 50 32 x 140 115 FM141-040D 25 38 x 89 88 FM141-040E 40cu 38 38 x 115 101 FM141-040F 50 38 x 140 115 PART NO. PIPE DIA. INS. FERRULE DIA. A FM141-050D 25 51 x 102 94 FM141-050E 50cu 38 51 x 127 109 FM141-050F 50 51 x 152 121 FM141-065D 25 65 x 115 101 FM141-065E 65cu 38 65 x 140 115 FM141-065F 50 65 x 165 128 FM141-080D 25 76 x 127 109 FM141-080E 80cu 38 76 x 152 121 FM141-080F 50 76 x 178 134 FM141-100D 25 102 x 152 121 FM141-100E 100cu 38 102 x 178 134 FM141-100F 50 102 x 203 147 FINISH: GALVANISED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 89
HEAVY DUTY SLIDE GUIDE FM142 FM142 HEAVY DUTY SLIDE GUIDE FOR STEEL PIPE PART NO. PIPE SIZE A FM142-168 150nb 142 FM142-220 200nb 168 FM142-273 250nb 195 FM142-324 300nb 242 FM142-355 350nb 258 FM142-406 400nb 283 FM142-506 500nb 333 FM142-610 600nb 385 FINISH: GALVANISED FM142 HEAVY DUTY SLIDE GUIDE FOR COPPER PIPE PART NO. PIPE SIZE A FM142-152 150cu 134 FM142-203 200cu 160 FM142-254 250cu 185 FM142-304 300cu 210 FINISH: POLYESTER POWDER COATED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 90
FM143 HEAVY DUTY SLIDE GUIDE AND TIMBER FERRULE FOR STEEL PIPE PART NO. PIPE DIA. INS. FERRULE DIA. A FM143-125A 25 140 x 190 153 FM143-125B 125nb 38 140 x 220 168 FM143-125C 50 140 x 240 178 FM143-150A 25 168 x 220 168 FM143-150B 150nb 38 168 x 240 178 FM143-150C 50 168 x 268 192 FM143-200A 25 220 x 275 196 FM143-200B 200nb 38 220 x 300 208 FM143-200C 50 220 x 324 220 FM143-250A 25 273 x 324 220 FM143-250B 250nb 38 273 x 356 236 FM143-250C 50 273 x 375 246 PART NO. PIPE DIA. INS. FERRULE DIA. A FM143-300A 25 324 x 375 268 FM143-300B 300nb 38 324 x 406 283 FM143-300C 50 324 x 424 292 FM143-350A 25 355 x 406 283 FM143-350B 350nb 38 355 x 424 292 FM143-350C 50 355 x 457 309 FM143-400A 25 406 x 457 309 FM143-400B 400nb 38 406 x 483 321 FM143-400C 50 406 x 508 334 FM143-450A 25 455 x 508 334 FM143-450B 450nb 38 455 x 533 347 FM143-450C 50 455 x 557 359 FINISH: GALVANISED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 91
HEAVY DUTY SLIDE GUIDE AND TIMBER FERRULE FOR COPPER PIPE FM143 PART NO. PIPE DIA. INS. FERRULE DIA. A FM143-125D 25 127 x 178 147 FM143-125E 125cu 38 127 x 203 160 FM143-125F 50 127 x 228 172 FM143-150D 25 152 x 203 160 FM143-150E 150cu 38 152 x 228 172 FM143-150F 50 152 x 252 184 FM143-200D 25 203 x 252 184 FM143-200E 200cu 38 203 x 275 196 FM143-200F 50 203 x 300 208 FM143-250D 25 254 x 300 208 FM143-250E 250cu 38 254 x 324 223 FM143-250F 50 254 x 355 236 FINISH: GALVANISED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 92
FM144 LIGHT DUTY SLIDE GUIDE FOR STEAM & CONDENSATE STEEL PIPE PART NO. PIPE DIA. INS. SIZE A FM144-015A 25 21 x 73 80 FM144-015B 15nb 38 21 x 102 94 FM144-015C 50 21 x 127 109 FM144-020A 25 27 x 76 80 FM144-020B 20nb 38 27 x 102 94 FM144-020C 50 27 x 127 109 FM144-025A 25 34 x 83 85 FM144-025B 25nb 38 34 x 115 101 FM144-025C 50 34 x 140 115 FM144-032A 25 43 x 89 88 FM144-032B 32nb 38 43 x 115 101 FM144-032C 50 43 x 140 115 FM144-040A 25 48 x 102 94 FM144-040B 40nb 38 48 x 127 109 FM144-040C 50 48 x 152 121 PART NO. PIPE DIA. INS. SIZE A FM144-050A 25 60 x 115 101 FM144-050B 50nb 38 60 x 140 115 FM144-050C 50 60 x 165 128 FM144-065A 25 73 x 127 109 FM144-065B 65nb 38 73 x 152 121 FM144-065C 50 73 x 178 134 FM144-080A 25 89 x 140 115 FM144-080B 80nb 38 89 x 165 128 FM144-080C 50 89 x 190 140 FM144-100A 25 115 x 165 128 FM144-100B 100nb 38 115 x 190 140 FM144-100C 50 115 x 220 155 FINISH: GALVANISED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 93
LIGHT DUTY SLIDE GUIDE FOR STEAM & CONDENSATE COPPER PIPE FM144 PART NO. PIPE DIA. INS. SIZE A FM144-015D 25 13 x 65 76 FM144-015E 15cu 38 13 x 89 88 FM144-015F 50 13 x 115 101 FM144-020D 25 19 x 70 78 FM144-020E 20cu 38 19 x 102 94 FM144-020F 50 19 x 127 109 FM144-025D 25 25 x 76 80 FM144-025E 25cu 38 25 x 102 94 FM144-025F 50 25 x 127 109 FM144-032D 25 32 x 83 85 FM144-032E 32cu 38 32 x 115 101 FM144-032F 50 32 x 140 115 FM144-040D 25 38 x 89 88 FM144-040E 40cu 38 38 x 115 101 FM144-040F 50 38 x 140 115 PART NO. PIPE DIA. INS. SIZE A FM144-050D 25 51 x 102 94 FM144-050E 50cu 38 51 x 127 109 FM144-050F 50 51 x 152 121 FM144-065D 25 65 x 115 101 FM144-065E 65cu 38 65 x 140 115 FM144-065F 50 65 x 165 128 FM144-080D 25 76 x 127 109 FM144-080E 80cu 38 76 x 152 121 FM144-080F 50 76 x 178 134 FM144-100D 25 102 x 152 121 FM144-100E 100cu 38 102 x 178 134 FM144-100F 50 102 x 203 147 FINISH: POLYESTER POWDER COATED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 94
FM145 HEAVY DUTY SLIDE GUIDE FOR STEAM & CONDENSATE STEEL PIPE PART NO. PIPE DIA. INS. SIZE A FM145-125A 25 140 x 190 153 FM145-125B 125nb 38 140 x 220 168 FM145-125C 50 140 x 240 178 FM145-150A 25 168 x 220 168 FM145-150B 150nb 38 168 x 240 178 FM145-150C 50 168 x 268 192 FM145-200A 25 220 x 275 196 FM145-200B 200nb 38 220 x 300 208 FM145-200C 50 220 x 324 220 FM145-250A 25 273 x 324 220 FM145-250B 250nb 38 273 x 356 236 FM145-250C 50 273 x 375 246 PART NO. PIPE DIA. INS. SIZE A FM145-300A 25 324 x 375 268 FM145-300B 300nb 38 324 x 406 283 FM145-300C 50 324 x 424 292 FM145-350A 25 355 x 406 283 FM145-350B 350nb 38 355 x 424 292 FM145-350C 50 355 x 457 309 FM145-400A 25 406 x 457 309 FM145-400B 400nb 38 406 x 483 321 FM145-400C 50 406 x 508 334 FM145-450A 25 455 x 508 334 FM145-450B 450nb 38 455 x 533 347 FM145-450C 50 455 x 557 359 FINISH: GALVANISED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 95
HEAVY DUTY SLIDE GUIDE FOR STEAM & CONDENSATE COPPER PIPE FM145 PART NO. PIPE DIA. INS. SIZE A FM145-125D 25 127 x 178 147 FM145-125E 125cu 38 127 x 203 160 FM145-125F 50 127 x 228 172 FM145-150D 25 152 x 203 160 FM145-150E 150cu 38 152 x 228 172 FM145-150F 50 152 x 252 184 FM145-200D 25 203 x 252 184 FM145-200E 200cu 38 203 x 275 196 FM145-200F 50 203 x 300 208 FM145-250D 25 254 x 300 208 FM145-250E 250cu 38 254 x 330 223 FM145-250F 50 254 x 355 236 FINISH: POLYESTER POWDER COATED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 96
FM146 LIGHT DUTY ROLLER GUIDE FM146 LIGHT DUTY ROLLER GUIDE FOR STEEL PIPE PART NO. PIPESIZE A FM146-021 15nb 89 FM146-027 20nb 92 FM146-034 25nb 95 FM146-043 32nb 100 FM146-048 40nb 102 FM146-060 50nb 108 FM146-073 65nb 116 FM146-089 80nb 122 FM146-115 100nb 137 FM146-140 125nb 150 FM146-168 150nb 164 FINISH: GALVANISED FM146 LIGHT DUTY ROLLER GUIDE FOR COPPER PIPE PART NO. PIPESIZE A FM146-015 15cu 84 FM146-020 20cu 88 FM146-025 25cu 91 FM146-032 32cu 94 FM146-038 40cu 97 FM146-051 50cu 104 FM146-064 65cu 110 FM146-076 80cu 116 FM146-102 100cu 129 FM146-127 125cu 144 FM146-152 150cu 156 FINISH: POLYESTER POWDER COATED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 97
LIGHT DUTY ROLLER GUIDE AND TIMBER FERRULE FOR STEEL PIPE FM147 PART NO. PIPE DIA. INS. FERRULE DIA. A FM147-015A 25 21 x 73 115 FM147-015B 15nb 38 21 x 102 129 FM147-015C 50 21 x 127 144 FM147-020A 25 27 x 76 116 FM147-020B 20nb 38 27 x 102 129 FM147-020C 50 27 x 127 144 FM147-025A 25 34 x 83 120 FM147-025B 25nb 38 34 x 115 136 FM147-025C 50 34 x 140 150 FM147-032A 25 43 x 89 123 FM147-032B 32nb 38 43 x 115 136 FM147-032C 50 43 x 140 150 FM147-040A 25 48 x 102 129 FM147-040B 40nb 38 48 x 127 144 FM147-040C 50 48 x 152 156 PART NO. PIPE DIA. INS. FERRULE DIA. A FM147-050A 25 60 x 115 136 FM147-050B 50nb 38 60 x 140 150 FM147-050C 50 60 x 165 163 FM147-065A 25 73 x 127 144 FM147-065B 65nb 38 73 x 152 156 FM147-065C 50 73 x 178 169 FM147-080A 25 89 x 140 150 FM147-080B 80nb 38 89 x 165 163 FM147-080C 50 89 x 190 175 FM147-100A 25 115 x 165 163 FM147-100B 100nb 38 115 x 190 175 FM147-100C 50 115 x 220 190 FINISH: GALVANISED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 98
FM147 LIGHT DUTY ROLLER GUIDE AND TIMBER FERRULE FOR COPPER PIPE PART NO. PIPE DIA. INS. FERRULE DIA. A FM147-015D 25 13 x 65 110 FM147-015E 15cu 38 13 x 89 123 FM147-015F 50 13 x 115 136 FM147-020D 25 19 x 70 114 FM147-020E 20cu 38 19 x 102 129 FM147-020F 50 19 x 127 144 FM147-025D 25 25 x 76 116 FM147-025E 25cu 38 25 x 102 129 FM147-025F 50 25 x 127 144 FM147-032D 25 32 x 83 120 FM147-032E 32cu 38 32 x 115 136 FM147-032F 50 32 x 140 150 FM147-040D 25 38 x 89 123 FM147-040E 40cu 38 38 x 115 136 FM147-040F 50 38 x 140 150 FINISH: GALVANISED PART NO. PIPE DIA. INS. FERRULE DIA. A FM147-050D 25 51 x 102 129 FM147-050E 50cu 38 51 x 127 144 FM147-050F 50 51 x 152 156 FM147-065D 25 65 x 115 136 FM147-065E 65cu 38 65 x 140 150 FM147-065F 50 65 x 165 163 FM147-080D 25 76 x 127 144 FM147-080E 80cu 38 76 x 152 156 FM147-080F 50 76 x 178 169 FM147-100D 25 102 x 152 156 FM147-100E 100cu 38 102 x 178 169 FM147-100F 50 102 x 203 181 A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 99
HEAVY DUTY ROLLER GUIDE FM148 A FM148 HEAVY DUTY ROLLER GUIDE FOR STEEL PIPE PART NO. PIPESIZE A FM148-168 150nb 185 FM148-220 200nb 211 FM148-273 250nb 238 FM148-324 300nb 267 FM148-355 350nb 283 FM148-406 400nb 308 FM148-506 500nb 360 FM148-610 600nb 412 FINISH: GALVANISED FM148 HEAVY DUTY ROLLER GUIDE FOR COPPER PIPE PART NO. PIPESIZE A FM148-152 150cu 177 FM148-203 200cu 203 FM148-254 250cu 228 FM148-304 300cu 253 FINISH: POLYESTER POWDER COATED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 100
FM149 HEAVY DUTY ROLLER GUIDE AND TIMBER FERRULE FOR STEEL PIPE PART NO. PIPE DIA. INS. FERRULE DIA. A FM149-125A 25 140 x 190 195 FM149-125B 125nb 38 140 x 220 210 FM149-125C 50 140 x 240 220 FM149-150A 25 168 x 220 210 FM149-150B 150nb 38 168 x 240 220 FM149-150C 50 168 x 268 235 FM149-200A 25 220 x 275 238 FM149-200B 200nb 38 220 x 300 251 FM149-200C 50 220 x 324 263 FM149-250A 25 273 x 324 263 FM149-250B 250nb 38 273 x 356 279 FM149-250C 50 273 x 375 289 PART NO. PIPE DIA. INS. FERRULE DIA. A FM149-300A 25 324 x 375 289 FM149-300B 300nb 38 324 x 406 308 FM149-300C 50 324 x 424 317 FM149-350A 25 355 x 406 308 FM149-350B 350nb 38 355 x 424 317 FM149-350C 50 355 x 457 334 FM149-400A 25 406 x 457 334 FM149-400B 400nb 38 406 x 483 345 FM149-400C 50 406 x 508 359 FM149-450A 25 455 x 508 359 FM149-450B 450nb 38 455 x 533 372 FM149-450C 50 455 x 557 384 FINISH: GALVANISED A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 101
HEAVY DUTY ROLLER GUIDE AND TIMBER FERRULE FOR COPPER PIPE FM149 FINISH: GALVANISED PART NO. PIPE DIA. INS. FERRULE DIA. A FM149-125D 25 127 x 178 189 FM149-125E 125cu 38 127 x 203 202 FM149-125F 50 127 x 228 214 FM149-150D 25 152 x 203 202 FM149-150E 150cu 38 152 x 228 214 FM149-150F 50 152 x 252 226 FM149-200D 25 203 x 252 226 FM149-200E 200cu 38 203 x 275 238 FM149-200F 50 203 x 300 251 FM149-250D 25 254 x 300 251 FM149-250E 250cu 38 254 x 330 266 FM149-250F 50 254 x 355 279 A DIMENSION IS A MINIMUM, CAN BE INCREASED TO SUIT INDIVIDUAL ON-SITE REQUIREMENTS 102
FM151 FM152 FM153 FM154 EYEBOLTS AND SPHERICAL WASHERS CLEVIS AND BLADE ENDS FM152 SPHERICAL WASHER PART NO. R FM152-M10 11 FM152-M12 14 FM152-M16 18 FM152-M20 22 FM152-M24 26 FM152-M30 32 FM152-M36 38 FINISH: GALVANISED OR PLAIN FM151 EYEBOLT ALL DIMENSIONS TO ORDER. FINISH: GALVANISED, PAINTED OR PLAIN FM153 HANGER CLEVIS PART NO C D1 D2 W x t BOX QTY FM153-M10 LD 70 11 11 25 x 3 100 FM153-M10 70 11 11 25 x 5 50 FM153-M12 75 14 14 40 x 6 25 FM153-M16 100 18 14 50 x 6 25 FM153-M20 112 22 22 75 x 10 10 FINISH: GALVANISED FM154 BLADE END HANGER PART NO ROD DIA. A B C H MAT. FM154-M10 10 55 15 25 11 25 x 5 FM154-M12 12 74 22 32 14 40 x 6 FM154-M16 16 82 25 32 18 75 x 10 FM154-M20 20 97 32 35 22 90 x 12 FM154-M24 24 115 35 40 26 90 x 12 FINISH: GALVANISED OR PLAIN 103
CANTILEVER FITTINGS FM1075-4 FM1075-8 FM1075-4 FM1075-8 FITS CHANNEL FM1000, FM2000, FM4001 FINISH: GALVANISED 104
FM155 FM156 FM157 FM158 FM132 FM150 CANTILEVER BRACKETS FM155 FLEXISTRUT CHANNEL TRAPEZE FINISH: GALVANISED FM156 FLEXISTRUT CANTILEVER BRACKET PART NO. A FM156-200 200 FM156-350 350 FM156-500 500 FM156-650 650 FM156-750 750 FINISH: GALVANISED FM157 FLEXISTRUT CANTILEVER BRACKET PART NO. A FM157-150 150 FM157-300 300 FM157-450 450 FM157-600 600 FINISH: GALVANISED FM158 FLEXISTRUT CANTILEVER BRACKET PART NO. A FM158-200 200 FM158-350 350 FM158-500 500 FM158-650 650 FM158-780 780 FINISH: GALVANISED 105
STANDARD CLEVIS PIPE HANGER FM160 PART NO. PIPE SIZE D B ROD BOLT M1 M2 FM160-021 15nb 21 80 10 M10 x 55 25 x 5 25 x 5 FM160-025 25cu 25 80 10 M10 x 60 25 x 5 25 x 5 FM160-027 20nb 27 80 10 M10 x 60 25 x 5 25 x 5 FM160-032 32cu 32 85 10 M10 x 70 25 x 5 25 x 5 FM160-034 25nb 34 85 10 M10 x 70 25 x 5 25 x 5 FM160-038 40cu 38 98 10 M10 x 70 25 x 5 25 x 5 FM160-043 32nb 43 98 10 M10 x 85 25 x 5 25 x 5 FM160-048 40nb 48 98 10 M10 x 85 25 x 5 25 x 5 FM160-051 50cu 51 98 10 M10 x 85 25 x 5 25 x 5 FM160-060 50nb 60 100 10 M10 x 95 25 x 5 25 x 5 FM160-064 65cu 64 100 12 M12 x 110 32 x 5 32 x 5 FM160-076 65nb 76 120 12 M12 x 110 32 x 5 32 x 5 FM160-089 80nb 89 125 12 M12 x 130 32 x 5 32 x 5 FM160-102 100cu 102 135 12 M12 x 150 32 x 5 32 x 5 FM160-115 100nb 115 145 16 M16 x 180 32 x 6 32 x 5 FM160-127 125cu 127 150 16 M16 x 180 32 x 6 32 x 5 FM160-140 125nb 140 165 16 M16 x 180 32 x 6 32 x 5 FM160-152 150cu 152 190 16 M16 x 190 40 x 6 40 x 5 FM160-168 150nb 168 190 20 M20 x 220 40 x 6 40 x 5 FM160-204 200cu 204 215 20 M20 x 240 40 x 8 40 x 6 FM160-220 200nb 220 215 20 M20 x 260 40 x 10 40 x 6 FM160-250 250cu 250 245 24 M20 x 300 50 x 8 50 x 6 FM160-273 250nb 273 245 24 M20 x 325 50 x 8 50 x 6 FM160-324 300nb 324 275 24 M20 x 375 50 x 10 50 x 6 FM160-355 350nb 355 310 24 M24 x 425 50 x 12 50 x 6 FM160-406 400nb 406 350 24 M24 x 475 65 x 12 65 x 6 FM160-457 450nb 457 410 30 M24 x 525 65 x 12 65 x 6 FM160-508 500nb 508 430 30 M24 x 600 75 x 16 75 x 10 FINISH: GALVANISED OR POLYESTER POWDER COATED 106
FM171 FM172 FM173 FM174 FM177 FM1271 FM3087 FM1271 BOX QTY:20 BEAM CLAMPS FOR FLEXISTRUT CHANNEL FM3087 BOX QTY:10 FM171 BOX QTY:50 FM172 BOX QTY:50 FM173 BOX QTY:25 FM177 FM174 BOX QTY:20 BOX QTY:10 FINISH: ZINC PLATED 107
BEAM ATTACHMENTS FM180 FM181 FM182 FM180 WELDED BEAM HANGER PART NO. A B C D1 D2 W x T FM180-10 75 32 20 14 11 50 x 10 FM180-12 75 32 20 14 14 50 x 10 FM180-16 75 50 30 18 18 75 x 10 FM180-20 90 50 30 22 22 75 x 10 FM180-24 125 50 40 26 26 100 x 12 FM181 WELDED BEAM HANGER PART NO. A B C D1 D2 W x T FM181-10 75 32 20 14 11 50 x 10 FM181-12 75 32 20 14 14 50 x 10 FM181-16 75 50 30 18 18 75 x 10 FM181-20 90 50 30 22 22 75 x 10 FM181-24 125 50 40 26 26 100 x 12 FM182 HANGER STIRRUP PART NO. A B C D D1 D2 W x T FM182-10 60 40 30 15 11 11 32 x 5 FM182-12 60 40 40 20 14 14 40 x 6 FM182-16 90 40 40 20 14 18 40 x 6 FM182-20 90 65 50 30 18 22 50 x 10 FM182-24 90 65 50 30 22 26 65 x 10 FINISH: PLAIN OR GALVANISED 108
FM189 FLOOR MOUNTED RISER GUIDE AND TIMBER FERRULE FOR STEEL PIPE PART NO. PIPE DIA. INS. FERRULE DIA. A FM189-015A 25 21 x 73 80 FM189-015B 15nb 38 21 x 102 94 FM189-015C 50 21 x 127 109 FM189-020A 25 27 x 76 80 FM189-020B 20nb 38 27 x 102 94 FM189-020C 50 27 x 127 109 FM189-025A 25 34 x 83 85 FM189-025B 25nb 38 34 x 115 101 FM189-025C 50 34 x 140 115 FM189-032A 25 43 x 89 88 FM189-032B 32nb 38 43 x 115 101 FM189-032C 50 43 x 140 115 FM189-040A 25 48 x 102 94 FM189-040B 40nb 38 48 x 127 109 FM189-040C 50 48 x 152 121 PART NO. PIPE DIA. INS. FERRULE DIA. A FM189-050A 25 60 x 115 101 FM189-050B 50nb 38 60 x 140 115 FM189-050C 50 60 x 165 128 FM189-065A 25 73 x 127 109 FM189-065B 65nb 38 73 x 152 121 FM189-065C 50 73 x 178 134 FM189-080A 25 89 x 140 115 FM189-080B 80nb 38 89 x 165 128 FM189-080C 50 89 x 190 140 FM189-100A 25 115 x 165 128 FM189-100B 100nb 38 115 x 190 140 FM189-100C 50 115 x 220 155 NOTE: FINISH: PIPE SIZES UP TO 100NB ARE SHOWN AS ABOVE. FOR LARGER SIZES OR OTHER SPECIAL ON-SITE REQUIREMENTS, CONSULT YOUR NEAREST FLEXISTRUT BRANCH. WHEN ORDERING, NOMINATE A DIMENSION. GALVANISED 109
FLOOR MOUNTED RISER GUIDE AND TIMBER FERRULE FOR COPPER PIPE FM189 PART NO. PIPE DIA. INS. FERRULE DIA. A FM189-015D 25 13 x 65 76 FM189-015E 15cu 38 13 x 89 88 FM189-015F 50 13 x 115 101 FM189-020D 25 19 x 70 78 FM189-020E 20cu 38 19 x 102 94 FM189-020F 50 19 x 127 109 FM189-025D 25 25 x 76 80 FM189-025E 25cu 38 25 x 102 94 FM189-025F 50 25 x 127 109 FM189-032D 25 32 x 83 85 FM189-032E 32cu 38 32 x 115 101 FM189-032F 50 32 x 140 115 FM189-040D 25 38 x 89 88 FM189-040E 40cu 38 38 x 115 101 FM189-040F 50 38 x 140 115 PART NO. PIPE DIA. INS. FERRULE DIA. A FM189-050D 25 51 x 102 94 FM189-050E 50cu 38 51 x 127 109 FM189-050F 50 51 x 152 121 FM189-065D 25 65 x 115 101 FM189-065E 65cu 38 65 x 140 115 FM189-065F 50 65 x 165 128 FM189-080D 25 76 x 127 109 FM189-080E 80cu 38 76 x 152 121 FM189-080F 50 76 x 178 134 FM189-100D 25 102 x 152 121 FM189-100E 100cu 38 102 x 178 134 FM189-100F 50 102 x 203 147 NOTE: FINISH: PIPE SIZES UP TO 100CU ARE SHOWN AS ABOVE. FOR LARGER SIZES OR OTHER SPECIAL ON-SITE REQUIREMENTS, CONSULT YOUR NEAREST FLEXISTRUT BRANCH. WHEN ORDERING, NOMINATE A DIMENSION. GALVANISED 110
FM190 FLOOR MOUNTED RISER GUIDE FM190 RISER GUIDE FOR STEEL PIPE PART NO. PIPE SIZE A FM190-021 15nb 54 FM190-027 20nb 57 FM190-034 25nb 60 FM190-043 32nb 65 FM190-048 40nb 67 FM190-060 50nb 73 FM190-073 65nb 81 FM190-089 80nb 88 FM190-115 100nb 101 FM190-140 125nb 155 FM190-168 150nb 129 FINISH: GALVANISED FM190 RISER GUIDE FOR COPPER PIPE PART NO. PIPE SIZE A FM190-015 15cu 49 FM190-020 20cu 53 FM190-025 25cu 56 FM190-032 32cu 59 FM190-038 40cu 62 FM190-051 50cu 73 FM190-064 65cu 76 FM190-076 80cu 81 FM190-102 100cu 94 FM190-127 125cu 108 FM190-152 150cu 121 FINISH: POLYESTER POWDER COATED NOTE: PIPE SIZES UP TO 150MM ARE SHOWN AS ABOVE. FOR LARGER SIZES OR OTHER SPECIAL ON-SITE REQUIREMENTS, CONSULT YOUR NEAREST FLEXISTRUT BRANCH. WHEN ORDERING, NOMINATE A DIMENSION. 111
FLOOR MOUNTED ANCHOR FM191 FM191 FLOOR MOUNTED ANCHOR FOR STEEL PIPE PART NO. PIPE SIZE A FM191-021 15nb 54 FM191-027 20nb 57 FM191-034 25nb 60 FM191-043 32nb 65 FM191-048 40nb 67 FM191-060 50nb 73 FM191-073 65nb 81 FM191-089 80nb 88 FM191-115 100nb 101 FM191-140 125nb 155 FM191-168 150nb 129 FINISH: GALVANISED FM191 FLOOR MOUNTED ANCHOR FOR COPPER PIPE PART NO. PIPE SIZE A FM191-015 15cu 49 FM191-020 20cu 53 FM191-025 25cu 56 FM191-032 32cu 59 FM191-038 40cu 62 FM191-051 50cu 73 FM191-064 65cu 76 FM191-076 80cu 81 FM191-102 100cu 94 FM191-127 125cu 108 FM191-152 150cu 121 FINISH: POLYESTER POWDER COATED NOTE: PIPE SIZES UP TO 150MM ARE SHOWN AS ABOVE. FOR LARGER SIZES OR OTHER SPECIAL ON-SITE REQUIREMENTS, CONSULT YOUR NEAREST FLEXISTRUT BRANCH. WHEN ORDERING, NOMINATE A DIMENSION. 112
FM191A WALL MOUNTED ANCHOR FM191A WALL MOUNTED ANCHOR FOR STEEL PIPE PART NO. PIPE SIZE A FM191A-021 15nb 54 FM191A-027 20nb 57 FM191A-034 25nb 60 FM191A-043 32nb 65 FM191A-048 40nb 67 FM191A-060 50nb 73 FM191A-073 65nb 81 FM191A-089 80nb 88 FM191A-115 100nb 101 FM191A-140 125nb 155 FM191A-168 150nb 129 FINISH: GALVANISED FM191A WALL MOUNTED ANCHOR FOR COPPER PIPE PART NO. PIPE SIZE A FM191A-015 15cu 49 FM191A-020 20cu 53 FM191A-025 25cu 56 FM191A-032 32cu 59 FM191A-038 40cu 62 FM191A-051 50cu 73 FM191A-064 65cu 76 FM191A-076 80cu 81 FM191A-102 100cu 94 FM191A-127 125cu 108 FM191A-152 150cu 121 FINISH: POLYESTER POWDER COATED NOTE: PIPE SIZES UP TO 150MM ARE SHOWN AS ABOVE. FOR LARGER SIZES OR OTHER SPECIAL ON-SITE REQUIREMENTS, CONSULT YOUR NEAREST FLEXISTRUT BRANCH. WHEN ORDERING, NOMINATE A DIMENSION. 113
SPIDER CLAMP FOR STEAM & CONDENSATE STEEL PIPE FM192 PART NO. PIPE DIA. INS. SIZE FM192-015A 25 21 x 73 FM192-015B 15nb 38 21 x 102 FM192-015C 50 21 x 127 FM192-020A 25 27 x 76 FM192-020B 20nb 38 27 x 102 FM192-020C 50 27 x 127 FM192-025A 25 34 x 83 FM192-025B 25nb 38 34 x 115 FM192-025C 50 34 x 140 FM192-032A 25 43 x 89 FM192-032B 32nb 38 43 x 115 FM192-032C 50 43 x 140 FM192-040A 25 48 x 102 FM192-040B 40nb 38 48 x 127 FM192-040C 50 48 x 152 FM192-050A 25 60 x 115 FM192-050B 50nb 38 60 x 140 FM192-050C 50 60 x 168 PART NO. PIPE DIA. INS. SIZE FM192-065A 25 73 x 127 FM192-065B 65nb 38 73 x 152 FM192-065C 50 73 x 178 FM192-080A 25 89 x 140 FM192-080B 80nb 38 89 x 165 FM192-080C 50 89 x 190 FM192-100A 25 115 x 165 FM192-100B 100nb 38 115 x 190 FM192-100C 50 115 x 220 FM192-125A 25 140 x 190 FM192-125B 125nb 38 140 x 220 FM192-125C 50 140 x 240 FM192-150A 25 168 x 220 FM192-150B 150nb 38 168 x 240 FM192-150C 50 168 x 268 FM192-200A 25 220 x 275 FM192-200B 200nb 38 220 x 300 FM192-200C 50 220 x 324 FINISH: GALVANISED 114
FM192 SPIDER CLAMP FOR STEAM & CONDENSATE COPPER PIPE PART NO. PIPE DIA. INS. SIZE FM192-015D 25 13 x 65 FM192-015E 15cu 38 13 x 89 FM192-015F 50 13 x 115 FM192-020D 25 19 x 70 FM192-020E 20cu 38 19 x 102 FM192-020F 50 19 x 127 FM192-025D 25 25 x 76 FM192-025E 25cu 38 25 x 102 FM192-025F 50 25 x 127 FM192-032D 25 32 x 83 FM192-032E 32cu 38 32 x 115 FM192-032F 50 32 x 140 FM192-040D 25 38 x 89 FM192-040E 40cu 38 38 x 115 FM192-040F 50 38 x 140 FM192-050D 25 51 x 102 FM192-050E 50cu 38 51 x 127 FM192-050F 50 51 x 152 PART NO. PIPE DIA. INS. SIZE FM192-065D 25 65 x 115 FM192-065E 65cu 38 65 x 140 FM192-065F 50 65 x 165 FM192-080D 25 76 x 127 FM192-080E 80cu 38 76 x 152 FM192-080F 50 76 x 178 FM192-100D 25 102 x 152 FM192-100E 100cu 38 102 x 178 FM192-100F 50 102 x 203 FM192-125D 25 127 x 178 FM192-125E 125cu 38 127 x 203 FM192-125F 50 127 x 228 FM192-150D 25 152 x 203 FM192-150E 150cu 38 152 x 228 FM192-150F 50 152 x 252 FM192-200D 25 203 x 252 FM192-200E 200cu 38 203 x 275 FM192-200F 50 203 x 300 FINISH: POLYESTER POWDER COATED 115
PIPE ROLLERS PIPE SPIDER FM193 FM194 FM195 FM193 PIPE SPIDER FINISH: PLAIN OR GALVANISED SPECIFY I.D. x O.D. x LENGTH FM194 PIPE ROLLERS ADJUSTABLE FOR PIPES 15nb TO 150nb FINISH: ROLLERS - CAST IRON BRACKETS - Z.P. FM195 PIPE ROLLER ASSEMBLY PART NO. FM195-1 FM195-2 FM195-3 FM195-4 FINISH: PIPE DIA. TO 125nb 125nb TO 200nb 200nb TO 300nb 300nb TO 400nb ROLLERS - CAST IRON BRACKETS - Z.P. 116
FM196 FM197 PIPE ROLLERS FM196 PIPE ROLLERS ADJUSTABLE FOR PIPES 150nb TO 450nb FINISH: ROLLERS - CAST IRON BRACKETS - Z.P. FM197 PIPE ROLLERS ADJUSTABLE FOR PIPES 400nb TO 600nb FINISH: ROLLERS - CAST IRON BRACKETS - Z.P. 117
FLEXICUSHION FLEXIBARRIER FM2600W FM2600B FM2600W FLEXICUSHION - COLOUR: WHITE - FLEXIBLE ELASTOMER MATERIAL - SOUND AND VIBRATION ISOLATION - SHOCK ABSORBTION - ELECTROLYSIS BARRIER - ABRASION PROTECTION - OPERATING TEMP -45 c TO +175 c - 10M ROLLS FM2600B FLEXIBARRIER - COLOUR: BLACK - PVC MATERIAL - ELECTROLYSIS BARRIER - ABRASION PROTECTION - ALLOWS CONTRACTION AND EXPANSION - 20M ROLLS 118
FM6 LIGHT DUTY DOUBLE BOLTED CLAMP PART NO. PIPE DIA. D BOLT MATERIAL BOX QTY FM6-015 15cu 12.7 M6x25 20x3 50 FM6-020 20cu 19 M6x25 20x3 50 FM6-021 15nb 21 M6x25 20x3 50 FM6-025 25cu 25 M6x25 20x3 50 FM6-027 20nb 27 M6x25 20x3 50 FM6-032 32cu 32 M6x25 20x3 50 FM6-034 25nb 34 M6x25 20x3 50 FM6-038 40cu 38 M6x25 20x3 25 FM6-043 32nb 43 M6x25 20x3 25 FM6-048 40nb 48 M6x25 20x3 25 FM6-051 50cu 51 M6x25 20x3 25 FM6-060 50nb 60 M6x25 20x3 25 FM6-064 65cu 64 M6x25 20x3 25 FM6-073 65nb 73 M6x25 20x3 25 FM6-076 80cu 76 M6x25 20x3 25 FM6-083 83ns 83 M6x25 20x3 20 FM6-089 80nb 89 M6x25 20x3 20 FM6-102 102cu 102 M6x25 20x3 20 FM6-115 100nb 115 M6x25 25x3 20 FM6-127 125cu 122 M8x30 25x5 10 FM6-140 125nb 140 M8x30 25x5 10 FM6-152 150cu 152 M8x30 25x5 10 FM6-168 150nb 168 M8x30 25x5 10 FM6-178 178ns 175 M8x30 25x5 10 FM6-190 190ns 190 M8x30 25x5 10 FM6-203 200cu 200 M8x30 25x5 10 FM6-220 200nb 220 M8x30 25x5 10 FM6-228 228ns 228 M8x30 25x5 10 FM6-240 240ns 240 M8x30 25x5 10 FM6-252 252ns 252 M8x30 25x5 10 FINISH: GALVANISED STANDARD FINISHES ONLY: OTHER FINISHES AVAILABLE ON REQUEST 119
LIGHT DUTY YOKE CLAMP FM8 PART NO. PIPE DIA. D BOLT MATERIAL BOX QTY FM8-020 20cu 19 M6x25 20x3 25 FM8-021 15nb 21 M6x25 20x3 25 FM8-025 25cu 25 M6x25 20x3 25 FM8-027 20nb 27 M6x25 20x3 25 FM8-032 32cu 32 M6x25 20x3 25 FM8-034 25nb 34 M6x25 20x3 25 FM8-038 40cu 38 M6x25 20x3 20 FM8-043 32nb 43 M6x25 20x3 20 FM8-048 40nb 48 M6x25 20x3 20 FM8-051 50cu 51 M6x25 20x3 20 FM8-060 50nb 60 M6x25 20x3 20 FM8-064 65cu 64 M6x25 20x3 20 FM8-073 65nb 73 M6x25 20x3 20 FM8-076 80cu 76 M6x25 20x3 20 FM8-083 83ns 83 M6x25 20x3 20 FM8-089 80nb 89 M6x25 20x3 20 FM8-102 102cu 102 M6x25 20x3 20 FM8-115 115nb 115 M6x25 25x3 20 FM8-127 125cu 127 M8x30 25x5 10 FM8-140 125nb 140 M8x30 25x5 10 FM8-152 150cu 152 M8x30 25x5 10 FM8-168 150nb 168 M8x30 25x5 10 FINISH: GALVANISED STANDARD FINISHES ONLY: OTHER FINISHES AVAILABLE ON REQUEST 120
FM15 MEDIUM DUTY SADDLES PART NO. PIPE DIA. D A B MATERIAL BOX QTY FM15-21 15nb 21 115 75 40x5 50 FM15-25 25cu 25 119 79 40x5 25 FM15-27 20nb 27 121 81 40x5 25 FM15-32 32cu 32 126 86 40x5 25 FM15-34 25nb 34 128 88 40x5 25 FM15-38 40cu 38 132 92 40x5 20 FM15-43 32nb 43 137 97 40x5 20 FM15-48 40nb 48 1472 102 40x5 20 FM15-51 50cu 51 145 105 40x5 20 FM15-60 50nb 60 154 114 40x5 10 FM15-64 65cu 64 158 118 40x5 10 FM15-73 65nb 73 167 127 40x5 10 FM15-76 80cu 76 170 130 40x5 5 FM15-89 80nb 89 183 143 40x5 5 FM15-102 102cu 102 196 156 40x5 5 FM15-115 100nb 115 210 170 40x6 5 FM15-127 127cu 127 223 183 40x6 5 FM15-140 125nb 140 236 196 40x6 5 FM15-152 152cu 152 248 208 40x6 5 FM15-168 150nb 168 261 221 40x6 5 FM15-203 200cu 203 299 259 40x6 5 FM15-220 200nb 220 315 275 40x6 5 FINISH: GALVANISED STANDARD FINISHES ONLY: OTHER FINISHES AVAILABLE ON REQUEST 121
MEDIUM DUTY DOUBLE BOLTED CLAMP FM16 PART NO. PIPE DIA. D BOLT MATERIAL BOX QTY FM16-48 40nb 48 M12x45 40x6 20 FM16-51 50cu 51 M12x45 40x6 20 FM16-60 50nb 60 M12x45 40x6 10 FM16-64 65cu 64 M12x45 40x6 10 FM16-73 65nb 73 M12x45 40x6 10 FM16-76 80cu 76 M12x45 40x6 10 FM16-83 83ns 83 M12x45 40x6 10 FM16-89 80nb 89 M12x45 40x6 10 FM16-102 100cu 102 M12x45 40x6 10 FM16-115 100nb 115 M12x45 40x6 10 FM16-127 125cu 127 M12x45 40x6 5 FM16-140 125nb 140 M12x45 40x6 5 FM16-152 152cu 152 M12x45 40x6 5 FM16-168 150nb 168 M12x45 40x6 5 FM16-175 175ns 175 M12x45 40x6 5 FM16-190 190ns 190 M12x45 40x6 5 FM16-203 200cu 203 M12x45 40x6 5 FM16-220 200nb 220 M12x45 40x6 5 FM16-228 228ns 228 M12x45 40x6 5 FM16-240 240ns 240 M12x45 40x6 5 FM16-252 250cu 252 M12x45 40x6 5 FM16-275 250nb 275 M12x45 40x6 5 FM16-304 300cu 304 M12x45 40x6 5 FM16-315 315ns 304 M12x45 40x6 5 FM16-324 300nb 324 M12x45 40x6 5 FINISH: GALVANISED STANDARD FINISHES ONLY: OTHER FINISHES AVAILABLE ON REQUEST 122
FM18 MEDIUM DUTY YOKE CLAMP PART NO. PIPE DIA. D HOLE DIA H BOLT MATERIAL BOX QTY FM18-60 50nb 60 14 M12x45 40x6 10 FM18-64 64cu 64 14 M12x45 40x6 10 FM18-73 65nb 73 14 M12x45 40x6 10 FM18-76 80cu 76 14 M12x45 40x6 10 FM18-83 83ns 83 14 M12x45 40x6 10 FM18-89 80nb 89 14 M12x45 40x6 10 FM18-102 100cu 102 14 M12x45 40x6 10 FM18-115 100nb 115 14 M12x45 40x6 5 FM18-127 125cu 127 14 M12x45 40x6 5 FM18-140 125nb 140 14 M12x45 40x6 5 FM18-152 152cu 152 14 M12x45 40x6 5 FM18-168 150nb 168 14 M12x45 40x6 5 FM18-175 175ns 175 14 M12x45 40x6 5 FM18-190 190ns 190 14 M12x45 40x6 5 FM18-203 200cu 203 14 M12x45 40x6 5 FM18-220 200nb 220 14 M12x45 40x6 5 FM18-228 228ns 228 14 M12x45 40x6 5 FM18-240 240ns 240 14 M12x45 40x6 5 FM18-252 250cu 252 14 M12x45 40x6 5 FM18-275 250nb 275 18 M12x45 40x6 5 FINISH: GALVANISED STANDARD FINISHES ONLY: OTHER FINISHES AVAILABLE ON REQUEST 123
EYE NUT FM35 D C B A PART NO. A B C D HOLE DIA. NUT W x T FM35-12-M10 70 20 30 16 14 M10 40 x 6 FM35-16-M12 75 25 30 18 18 M12 75 x 12 FM35-20-M16 90 30 35 24 22 M16 100 x 12 FM35-24-M20 95 30 35 30 26 M20 100 x 12 FM35-30-M24 125 35 50 36 32 M24 100 x 20 FM35-36-M30 145 40 60 46 38 M30 100 x 20 FM35-42-M36 150 40 60 55 42 M36 130 x 20 FINISH: GALVANISED STANDARD FINISHES ONLY: OTHER FINISHES AVAILABLE ON REQUEST 124
GENERAL ARRANGEMENT GAS RISER PIPE SUPPORTS SPRING SELECTION: CONTACT YOUR NEAREST FLEXISTRUT BRANCH FOR CORRECT SPRING SELECTION 125
GAS RISER ANCHOR - WALL MOUNT GAS RISER GUIDE - WALL MOUNT FMGR-001 FMGR-002 FMGR-001 GAS RISER ANCHOR WALL MOUNT PART NO. FMGR-001-015 FMGR-001-020 FMGR-001-025 FMGR-001-032 FMGR-001-040 FMGR-001-050 FMGR-001-065 FMGR-001-076 FMGR-001-100 FMGR-001-125 FMGR-001-150 PIPE DIA. 15cu 20cu 25cu 32cu 40cu 50cu 65cu 80cu 100cu 125cu 150cu FINISH: POLYESTER POWDER COATED FMGR-002 GAS RISER GUIDE WALL MOUNT PART NO. FMGR-002-015 FMGR-002-020 FMGR-002-025 FMGR-002-032 FMGR-002-040 FMGR-002-050 FMGR-002-065 FMGR-002-076 FMGR-002-100 FMGR-002-125 FMGR-002-150 PIPE DIA. 15cu 20cu 25cu 32cu 40cu 50cu 65cu 80cu 100cu 125cu 150cu FINISH: POLYESTER POWDER COATED 126
FMGR-003 FMGR-004 GAS RISER SPRING ASSEMBLY - WALL MOUNT GAS RISER HORIZONTAL - WALL MOUNT FMGR-003 GAS RISER SPRING ASSEMBLY WALL MOUNT PART NO. FMGR-003-015 FMGR-003-020 FMGR-003-025 FMGR-003-032 FMGR-003-040 FMGR-003-050 FMGR-003-065 FMGR-003-076 FMGR-003-100 FMGR-003-125 FMGR-003-150 PIPE DIA. 15cu 20cu 25cu 32cu 40cu 50cu 65cu 80cu 100cu 125cu 150cu FINISH: POLYESTER POWDER COATED FMGR-004 GAS RISER HORIZONTAL WALL MOUNT PART NO. PIPE DIA. ROD DIA. FMGR-004-015 15cu M10 FMGR-004-020 20cu M10 FMGR-004-025 25cu M10 FMGR-004-032 32cu M10 FMGR-004-040 40cu M10 FMGR-004-050 50cu M10 FMGR-004-065 65cu M12 FMGR-004-076 80cu M12 FMGR-004-100 100cu M16 FMGR-004-125 125cu M16 FMGR-004-150 150cu M20 FINISH: POLYESTER POWDER COATED NOTE: ROD DIAMETERS DERIVED FROM AG601 TABLE 4.3 127
GAS RISER ANCHOR - FLOOR MOUNT GAS RISER GUIDE - FLOOR MOUNT FMGR-005 FMGR-006 FMGR-005 GAS RISER ANCHOR FLOOR MOUNT PART NO. FMGR-005-015 FMGR-005-020 FMGR-005-025 FMGR-005-032 FMGR-005-040 FMGR-005-050 FMGR-005-065 FMGR-005-076 FMGR-005-100 FMGR-005-125 FMGR-005-150 PIPE DIA. 15cu 20cu 25cu 32cu 40cu 50cu 65cu 80cu 100cu 125cu 150cu FINISH: POLYESTER POWDER COATED FMGR-006 GAS RISER GUIDE FLOOR MOUNT PART NO. FMGR-006-015 FMGR-006-020 FMGR-006-025 FMGR-006-032 FMGR-006-040 FMGR-006-050 FMGR-006-065 FMGR-006-076 FMGR-006-100 FMGR-006-125 FMGR-006-150 PIPE DIA. 15cu 20cu 25cu 32cu 40cu 50cu 65cu 80cu 100cu 125cu 150cu FINISH: POLYESTER POWDER COATED 128
FMGR-007 FMGR-008 GAS RISER SPRING ASSEMBLY - FLOOR MOUNT GAS RISER HORIZONTAL - FLOOR MOUNT FMGR-007 GAS RISER SPRING ASSEMBLY FLOOR MOUNT PART NO. FMGR-007-015 FMGR-007-020 FMGR-007-025 FMGR-007-032 FMGR-007-040 FMGR-007-050 FMGR-007-065 FMGR-007-076 FMGR-007-100 FMGR-007-125 FMGR-007-150 PIPE DIA. 15cu 20cu 25cu 32cu 40cu 50cu 65cu 80cu 100cu 125cu 150cu FINISH: POLYESTER POWDER COATED FMGR-008 GAS RISER HORIZONTAL FLOOR MOUNT PART NO. PIPE DIA. ROD DIA. FMGR-008-015 15cu M10 FMGR-008-020 20cu M10 FMGR-008-025 25cu M10 FMGR-008-032 32cu M10 FMGR-008-040 40cu M10 FMGR-008-050 50cu M10 FMGR-008-065 65cu M12 FMGR-008-076 80cu M12 FMGR-008-100 100cu M16 FMGR-008-125 125cu M16 FMGR-008-150 150cu M20 FINISH: POLYESTER POWDER COATED NOTE: ROD DIAMETERS DERIVED FROM AG601 TABLE 4.3 129
SPRING CAGES FMGR-SPS FMGR-SPL SPRING CAGE ASSEMBLY PART NO. FMGR-SPS ROD DIA M10 HEIGHT 107 mm WIDTH 72 mm LOAD 100 kg FMGR-SPL M12 / M16 148 mm 82 mm 300 kg SPRING CAGE USED FOR VIBRATION SUPPORT SYSTEM FINISH: POLYESTER POWDER COATED 130
IM Y SERIES HS Y SERIES VIBRATION ISOLATION HANGER SPRING Y SERIES PART NO. HS-Y-10 COLOUR SILVER RATED LOAD (kgs) 10 RATED DEFL. (mm) 20 HS-Y-15 GOLD 15 20 HS-Y-30 BLACK 30 20 HS-Y-50 SILVER 50 20 HS-Y-60 BLUE 60 20 MAX ROD DIA. 10MM IM Y SERIES PART NO. IM-Y-10 COLOUR SILVER RATED LOAD (kgs) 10 RATED DEFL. (mm) 20 IM-Y-15 GOLD 15 20 IM-Y-30 BLACK 30 20 IM-Y-50 SILVER 50 20 IM-Y-60 BLUE 60 20 MAX ROD DIA. 10MM 131
BOD COD VIBRATION ISOLATION TYPE IM PART NO. RATED CAPACITY (kg) IM X AND A SERIES RATED DEFL. (mm) SPRING CONSTANT (kg/mm) SPRING COLOUR/STRIP IM-X-23 10 33 0.32 BROWN E IM-X-33 15 28 0.54 RED IM-X-54 25 30 0.81 WHITE IM-X-76 35 26 1.33 BLACK IM-X-113 51 25 2.02 YELLOW IM-X-130 59 25 2.33 PURPLE IM-X-175 80 25 3.13 SILVER IM-X-210 95 25 3.76 BLUE IM-A-12 5 25 0.21 RED IM-A-18 8 25 0.32 GREY IM-A-25 11 25 0.45 ORANGE IM-A-45 20 41 0.50 BLUE IM-A-75 34 38 0.89 ORANGE IM-A-125 57 34 1.68 BROWN IM-A-200 91 29 3.11 BLACK IM-A-310 141 25 5.55 YELLOW IM-A-400 182 25 7.16 GREEN IM-A-510 232 25 9.13 RED IM-A-625 284 25 11.18 WHITE NEOPRENE SPRING CUP STEEL CAP RP ROD PENETRATION SIZE TYPE IM DIMENSIONS (mm) BUSHING OUSIDE DIA. (BOD) ROD PENETRATION (RP) CUP OUTSIDE DIA. (COD) MAX ROD DIA. (MDR) IM-X-23 TO 210 22 51 10 70 IM-X-12 TO 25 25 54 10 57 IM-A-45 TO 400 25 54 13 86 IM-A-510 25 54 13 89 IM-A-625 25 54 13 95 132
TYPE N TYPE ND VIBRATION ISOLATION PART NO. TYPE N RUBBER MOUNTS DUROMETER RATED LOAD (kg) DEFL. (mm) N-A-BLACK 30 16 4 N-A-GREEN 40 25 4 N-A-RED 50 40 4 N-B-RED 50 110 5 N-B-WHITE 60 180 5 N-B-YELLOW 70 270 5 N-C-RED 50 185 6 N-C-WHITE 60 280 6 N-C-YELLOW 70 460 6 TYPE N DIMENSIONS SIZE D H L T W BC CS MBD N-A 30 22 80 5 40 63 8 8 N-B 45 28 98 6 58 75 10 10 N-C 70 40 140 6 84 105 12 14 TYPE ND RUBBER MOUNTS PART NO. DUROMETER RATED LOAD (kg) DEFL. (mm) ND-A-BLACK 30 7-21 9 ND-A-GREEN 40 14-34 9 ND-A-RED 50 27-57 9 ND-B-BLACK 30 23-45 10 ND-B-GREEN 40 34-68 10 ND-B-RED 50 50-107 10 ND-B-WHITE 60 82-173 10 ND-B-YELLOW 70 136-273 10 ND-C-GREEN 40 64-118 13 ND-C-RED 50 91-182 13 ND-C-WHITE 60 141-273 13 ND-C-YELLOW 70 236-455 13 TYPE ND DIMENSIONS SIZE D H L T W BC CS MBD ND-A 30 38 81 5 41 61 8 8 ND-B 45 48 99 6 59 77 10 8 ND-C 65 70 140 6 84 105 12 13 ND-D 86 70 159 8 102 128 12 13 133
VIBRATION ISOLATION HD-E RL-4 PART NO. HD ELEMENT DUROMETER RATED LOAD (kg) MAX DEFL. (mm) HD-E-GREEN 40 UP TO 16 5 HD-E-WHITE 60 16-34 5 HD-A-E-BLACK 30 UP TO 20 9 HD-A-E-GREEN 40 30-75 9 HD-A-E-RED 50 60-125 9 HD ELEMENT DIMENSIONS (mm) SIZE LD UD H ID OD MAX ROD DIA. HD-E 35 32 29 11 17 10 HD-A-E 45 38 38 21 27 13 HD HANGER DIMENSIONS (mm) SIZE D H W LRP MRD HD-E 35 32 29 11 17 HD-A-E 45 38 38 21 27 PART NO. RL MOUNT PART NO. MAX LOAD kgs. COLOUR CODE TAPPED HOLE RL-4-GREEN 68 GREEN 10mm RL-4-RED 113 RED 10mm RL-4-WHITE 181 WHITE 10mm COMES WITH 64mm LONG LEVELING STUD, NUTS AND WASHERS HD HANGER DUROMETER RATED LOAD (kg) MAX DEFL. (mm) HD-GREEN 40 UP TO 16 5 HD-WHITE 60 16-34 5 HD-A-BLACK 30 UP TO 20 9 HD-A-GREEN 40 30-75 9 HD-A-RED 50 60-125 9 134
WAFFLE VIBRATION ISOLATION PART NO WAFFLE WAFFLE-SUPER WAFFLE PADS DESCRIPTION 450 x 450 x 10mm 450 x 450 x 20mm NATURAL RUBBER FOR MAXIMUM RESILIENCE AND VIBRATION ISOLATION. CONTAINS ANTI-OXIDANTS AND ANTI- OZANTS TO IMPROVE AGING. STANDARD NEOPRENE TO MODERATE OIL RESISTANCE DUCTCLEAT SPRING DUCT WORK DUCTCLEAT-SHORT DUCTCLEAT-LONG DUCT CLEAT PART NO. SIZE BOX QTY DUCTCLEAT-SHORT SHORT LEG 100 DUCTCLEAT-LONG LONG LEG 100 DUCT-TOOL TOOL EA REGISTER SPRING PART NO. SIZE FINISH BOX QTY SPRING-10x75 10 x 75 UNPLATED 1000 SPRING-20X35 20 x 35 UNPLATED 500 135
DUCTWORK FLEXISTRUT Z BRACKET PART NO. BOX QTY Z-CLIP 100 FINISH: ZINC PLATED FLEXISTRUT DUCT BOLT PART NO. BOX QTY FM34HB10 50 10mm BOLT FINISH: ZINC PLATED FLEXISTRUT DUCT EAR PART NO. BOX QTY FM34CNR 50 FINISH: GALVABOND 136
33 14.5 FSF90 FSF45 FLF90 FLF45 FSF45 FSF90 BRACING SYSTEM 14.5 38 38 38 40 FLF90 FLF45 14.5 14.5 32 50 24 58 FINISH: GALVANISED MATERIAL: 25 x 3 mm HOLE DIA: 11 mm 137
100 SERIES SHANKLESS CLIP EB100 EC100 ES100 EA100 EP100 EH100 NOM. PART NUMBERS SIZE COPPER STEEL CAST IRON DWV P.V.C. PRESS P.V.C H.D.P.E 15 EC100-015 ES100-021 EH100-021 20 EC100-020 ES100-027 EH100-027 25 EC100-025 ES100-034 EH100-034 EB100-032 32 EC100-032 ES100-043 EP100-038 EH100-043 EB100-040 40 EC100-038 ES100-048 EP100-043 EH100-048 EB100-050 50 EC100-051 ES100-060 EA100-060 EP100-060 EH100-060 EB100-056 65 EC100-064 ES100-076 EA100-076 EP100-076 EH100-076 EB100-065 80 EC100-076 ES100-089 EA100-089 EP100-083 EH100-089 EB100-075 90 EB100-090 100 EC100-102 ES100-115 EA100-115 EP100-110 EH100-115 EB100-110 125 EC100-127 ES100-140 EA100-140 EP100-140 EH100-140 EB100-125 150 EC100-152 ES100-165 EA100-165 EP100-160 EH100-160 EB100-160 FINISH: POLY ZINC ZINC POLY POLY POLY BROWN PLATED PLATED WHITE WHITE BLACK 138
EC200 ES200 EA200 EP200 EH200 EB200 200 SERIES NUT CLIP. NOM SIZE PART NUMBERS COPPER STEEL CAST IRON DWV P.V.C. PRESS P.V.C. HDPE 15 EC200-015 ES200-021 EH200-021 20 EC200-020 ES200-027 EH200-027 25 EC200-025 ES200-034 EH200-034 32 EC200-032 ES200-043 EP200-038 EH200-043 EB200-040 40 EC200-038 ES200-048 EP200-043 EH200-048 EB200-050 50 EC200-051 ES200-060 EA200-060 EP200-060 EH200-060 EB200-056 65 EC200-064 ES200-076 EA200-076 EP200-076 EH200-076 EB200-065 80 EC200-076 ES200-089 EA200-089 EP200-083 EH200-089 EB200-075 90 EB200-090 100 EC200-102 ES200-115 EA200-115 EP200-115 EH200-115 EB200-110 125 EC200-127 ES200-140 EA200-140 EP200-140 EH200-140 EB200-125 150 EC200-152 ES200-165 EA200-165 EP200-165 EH200-165 EB200-165 175 EP200-175 EB200-180 200 EP200-200 EB200-200 225 250 EP200-250 EB200-250 300 EP200-315 EB200-315 FINISH: POLY ZINC ZINC POLY POLY POLY BROWN PLATED PLATED WHITE WHITE BLACK 139
300 SERIES SHANK CLIP EC300 ES300 EA300 EP300 EH300 ORDER EXAMPLE: EC300-051B DENOTES 50cu + 225mm SHANK SHANK MATERIAL 20mm x 3mm NOM. PART NUMBERS SIZE COPPER STEEL CAST IRON DWV P.V.C. PRESS P.V.C. 15 EC300-015 ES300-021 EH300-021 20 EC300-020 ES300-027 EH300-027 25 EC300-025 ES300-034 EH300-034 32 EC300-032 ES300-043 EP300-038 EH300-043 40 EC300-038 ES300-048 EP300-043 EH300-048 50 EC300-051 ES300-060 EA300-060 EP300-060 EH300-060 65 EC300-064 ES300-076 EA300-076 EP300-076 EH300-076 80 EC300-076 ES300-089 EA300-089 EP300-083 EH300-089 100 EC300-102 ES300-115 EA300-115 EP300-115 EH300-115 125 EC300-127 ES300-140 EA300-140 EP300-140 EH300-140 150 EC300-152 ES300-165 EA300-165 EP300-165 EH300-165 FINISH: POLY ZINC ZINC POLY POLY BROWN PLATED PLATED WHITE WHITE 140
EP300 300 SERIES FLEXI SHANK CLIP FINISH: POLY WHITE SHANK MATERIAL 25mm X 1.2mm PIPE SIZE CODE LENGTH 32 P.V.C EP300-038D 450mm 40 P.V.C EP300-043D 450mm 65 P.V.C EP300-076D 450mm 80 P.V.C EP300-083D 450mm 100 P.V.C EP300-115D 450mm 125 P.V.C EP300-140D 450mm 150 P.V.C EP300-165D 450mm PIPE SIZE CODE LENGTH 32 P.V.C EP300-038E 600mm 40 P.V.C EP300-043E 600mm 65 P.V.C EP300-076E 600mm 80 P.V.C EP300-083E 600mm 100 P.V.C EP300-115E 600mm 125 P.V.C EP300-140E 600mm 150 P.V.C EP300-165E 600mm 141
STANDARD PEAR BANDS EC500 PEAR BAND FOR COPPER PIPE PART NO. PIPE DIA. MATERIAL ROD DIA. EC500-032 32cu 25 x 1.6 M10 EC500-038 40cu 25 x 1.6 M10 EC500-051 50cu 25 x 1.6 M10 EC500-064 65cu 32 x 2.0 M10 EC500-076 80cu 32 x 2.0 M10 EC500-102 100cu 32 x 2.0 M10 EC500-127 125cu 32 x 2.0 M12 EC500-152 150cu 40 x 3.0 M12 FINISH: POLYESTER POWDER COATED - BROWN EC500 EP500 EF500 EP500 PEAR BAND FOR P.V.C. PIPE PART NO. PIPE DIA. MATERIAL ROD DIA. EP500-38 32pvc 25 x 1.6 M10 EP500-43 38pvc 25 x 1.6 M10 EP500-48 40press 25 x 1.6 M10 EP500-60 50pvc 25 x 1.6 M10 EP500-76 65pvc 32 x 2.0 M10 EP500-89 80pvc 32 x 2.0 M10 EP500-115 100pvc 32 x 2.0 M10 EP500-140 125pvc 40 x 3.0 M12 EP500-165 150pvc 40 x 3.0 M12 FINISH: POLYESTER POWDER COATED - WHITE EF500 PEAR BAND FOR STEEL PIPE PART NO. PIPE DIA. MATERIAL ROD DIA. EF500-027 20nb 25 x 1.6 M10 EF500-034 25nb 25 x 1.6 M10 EF500-043 32nb 25 x 1.6 M10 EF500-048 40nb 25 x 1.6 M10 EF500-060 50nb 25 x 1.6 M10 EF500-076 65nb 32 x 2.0 M12 EF500-089 80nb 32 x 2.0 M12 EF500-115 100nb 32 x 2.0 M12 EF500-140 125nb 40 x 3.0 M12 EF500-165 150nb 40 x 3.0 M12 EF500-220 200nb 50 x 3.0 M12 FINISH: GALVABOND STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST FM APPROVAL PEAR BANDS AVAILABLE ON REQUEST 142
S - SERIES ACOUSTIC PIPE CLIPS The Flexistrut Acoustic S Clip has many advantages: -It is insulated -It has a combination 8mm & 10mm Nut to allow for either size of threaded rod to be used. -It can be used as is for a fixed point -It can be used with a spacer so that it will become a sliding point COES Australia recommends the Flexistrut - Acoustic S Series clip for coestherm pipe. PART NO. TO SUIT BOX Copper Pipe Steel Pipe Pressure PVC DWV PVC Pipe HDPE Pipe PP_R Pipe QTY S12-14 15CU 50 S19-21 20CU 20HDPE 50 S21-23 15NB 15NB 50 S20-25 25CU 25HDPE 25mm 50 S26-28 20NB 20NB 25 S32-35 32CU 25NB 25NB 32HDPE 32mm 25 S40-43 40CU 32NB 32NB 32PVC 40HDPE 40mm 25 S44-49 40NB 40NB 50HDPE 20 S50-56 50CU 50PVC 50mm 20 S57-62 50NB 50NB 20 S63-67 65CU 65HDPE 63mm 20 S67-70 65PVC 20 S74-80 80CU 65NB 65NB 80HDPE 75mm 20 S83-91 80NB 80NB 80PVC 90HDPE 90mm 20 S101-106 100CU 20 S108-114 100NB 100NB 100PVC 100HDPE 110mm 20 S125 125CU 125HDPE 125mm 20 S140-144 125NB 125NB 20 S152 150CU 20 S159-163 150NB 150PVC 150HDPE 160mm 20 S165-169 150NB 20 TECHNICAL DATA FINISH: ZINC PLATED RUBBER QUALITY: EPDM (without polymer mix) Shore hardness 45 5 ShoreA (DIN 53505) Compression set 30% (DIN 53517) Shore hardness change after aging 10 (DIN 53508) Resistance ozone cracking (DIN 53509) Temperature range -50C to +110C (DIN 53513) Flame test B2, (DIN 4102) 143
STANDARD SADDLE CLAMP FOR F.R.C. FM118 PART NO. PIPE SIZE BARREL O.D SPIGOT O.D HOLE DIA MATERIAL FM118-257 225nb - 257 14 40 x 6 FM118-269 225nb 269-14 40 x 6 FM118-336 300nb - 336 14 40 x 6 FM118-346 300nb 346-14 40 x 6 FM118-414 375nb - 414 18 50 x 6 FM118-427 375nb 427-18 50 x 6 FM118-504 450nb - 504 18 50 x 10 FM118-512 450nb 512-18 50 x 10 FM118-584 525nb - 584 22 75 x 10 FM118-594 525nb 594-22 75 x 10 FM118-665 600nb - 665 22 75 x 12 FM118-680 600nb 680-22 75 x 12 FM118-733 675nb - 733 22 75 x 12 FM118-752 675nb 752-22 75 x 12 FM118-783 750nb - 783 22 75 x 12 FM118-802 750nb 802-22 75 x 12 SIZES BASED ON FIBRE REINFORCED CEMENT PIPE CLASS 2 STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST FINISH: GALVANISED 144
FM119 STANDARD BOLTED CLAMP FOR F.R.C. PART NO. PIPE SIZE BARREL O.D SPIGOT O.D BOLT MATERIAL FM119-257 225nb - 257 M12 x 45 40 x 6 FM119-269 225nb 269 - M12 x 45 40 x 6 FM119-336 300nb - 336 M12 x 45 40 x 6 FM119-346 300nb 346 - M12 x 45 40 x 6 FM119-415 375nb - 415 M16 x 50 50 x 6 FM119-427 375nb 427 - M16 x 50 50 x 6 FM119-504 450nb - 504 M20 x 75 50 x 10 FM119-512 450nb 512 - M20 x 75 50 x 10 FM119-584 525nb - 584 M20 x 75 75 x 10 FM119-594 525nb 594 - M20 x 75 75 x 10 FM119-664 600nb - 664 M24 x 90 75 x 12 FM119-680 600nb 680 - M24 x 90 75 x 12 FM119-733 675nb - 733 M24 x 90 75 x 16 FM119-752 675nb 752 - M24 x 90 75 x 16 FM119-783 750nb - 783 M24 x 90 75 x 16 FM119-802 750nb 802 - M24 x 90 75 x 16 SIZES BASED ON FIBRE REINFORCED CEMENT PIPE CLASS 2 STANDARD SIZES ONLY: OTHER SIZES AVAILABLE ON REQUEST FINISH: GALVANISED 145
FIRE PROTECTION PRODUCTS EF100 EF200 EF300 EF400 EF100 L.D. SHALLOW SADDLE PART NO PIPE DIA. BAG QTY EF100-034 25nb 100 EF100-043 32nb 100 EF100-048 40nb 100 EF100-060 50nb 50 FINISH: GALVABOND EF200 L.D. DEEP SADDLE PART NO PIPE DIA. BAG QTY EF200-034 25nb 100 EF200-043 32nb 50 EF200-048 40nb 50 EF200-060 50nb 25 FINISH: GALVABOND EF300 TWIST CLIP PART NO PIPE DIA. BAG QTY EF300-034 25nb 100 EF300-043 32nb 100 EF300-048 40nb 50 EF300-060 50nb 50 EF300-076 65nb 50 FINISH: GALVABOND PART NO EF400 NUT CLIP PIPE DIA. MATERIAL NUT BOLT & NUT BOX QTY EF400-027 20nb 20 x 3 M10 1/4 x 1 50 EF400-034 25nb 20 x 3 M10 1/4 x 1 25 EF400-043 32nb 20 x 3 M10 1/4 x 1 25 EF400-048 40nb 20 x 3 M10 1/4 x 1 25 EF400-060 50nb 20 x 3 M10 1/4 x 1 25 EF400-076 65nb 25 x 3 M12 1/4 x 1 20 EF400-089 80nb 25 x 3 M12 5/16 x 1 1/2 25 EF400-115 100nb 25 x 5 M12 5/16 x 1 1/2 20 EF400-140 125nb 25 x 5 M12 5/16 x 1 1/2 20 EF400-165 150nb 25 x 5 M12 5/16 x 1 1/2 20 FINISH: ZINC PLATED Conforms to SAA code AS2118 146
EF500 EF600 EF700 FIRE PROTECTION PRODUCTS EF500 PEAR BAND PART NO PIPE DIA. MATERIAL ROD DIA. BAG QTY EF500-027 20nb 25 x 1.6 M10 100 EF500-034 25nb 25 x 1.6 M10 100 EF500-043 32nb 25 x 1.6 M10 100 EF500-048 40nb 25 x 1.6 M10 100 EF500-060 50nb 25 x 1.6 M10 100 EF500-076 65nb 32 x 2.0 M12 50 EF500-089 80nb 32 x 2.0 M12 50 EF500-115 100nb 32 x 2.0 M12 20 EF500-140 125nb 40 x 3.0 M12 - EF500-165 150nb 40 x 3.0 M12 - EF500-220 200nb 40 x 3.0 M16 - FINISH: GALVABOND CONFORMS TO SAA CODE AS2118 FM APPROVAL PEAR BANDS AVAILABLE ON REQUEST EF600 U BOLT PART NO PIPE DIA. MATERIAL EF600-034 25nb M6 EF600A-034 25nb M10 EF600-043 32nb M6 EF600A-043 32nb M10 EF600-048 40nb M6 EF600A-048 40nb M10 EF600-060 50nb M6 EF600A-060 50nb M10 EF600-076 65nb M12 EF600-089 80nb M12 EF600-115 100nb M12 EF600-140 125nb M12 EF600-165 150nb M12 EF600-220 200nb M16 FINISH: ZINC PLATED AND GALVANISED EF700 / EF700LD PIPE BEAM CLIP PART NO PIPE DIA. U BOLT EF700LD 25nb to 50nb M6 EF700 25nb to 50nb M10 FINISH: ZINC PLATED U Bolt to be ordered SEPARATELY. Sizes above 50nb available on request. 147
FIRE PROTECTION PRODUCTS BEAM ATTACHMENTS BEAM CLAMP HOOK BOLT PART NO. A B PART NO. C D EF800-050 50 12 EF900-075 75 12 EF800-100 100 12 EF900-100 100 12 EF800-150 150 12 EF900-135 135 12 EF900-175 175 12 EF1000-050 50 10 EF1100-075 75 10 EF1000-100 100 10 EF1100-100 100 10 EF1000-150 150 10 EF1100-135 135 10 EF1100-175 175 10 EF800 EF900 EF1000 EF1100 EF1200 EF1200A EF1200B EF1200 MOUNTING PLATES PART NO THREAD BOX QTY EF1200A-M10 M10 50 EF1200A-M12 M12 50 EF1200B-M10 M10 50 EF1200B-M12 M12 50 EF1200C-M10 M10 50 EF1200C-M12 M12 50 EF1200L-M10 M10 50 EF1200SP-M10 M10 50 EF1200SP-M10 EF1200L-M10 EF1200C FINISH: ZINC PLATED 148
EF1300 EF1400 EF12000 FIRE PROTECTION PRODUCTS EF1300-M11 ANGLE BRACKET BOX QTY: 100 EF1300 ANGLE BRACKET BOX QTY: 50 EF12000 ANGLE BRACKET FINISH: GALVABOND FINISH: GALVANISED FINISH: GALVANISED EF1400 PURLIN CLEAT PART NO U BOLT DIA. BOX QTY EF1400-M6 M6 200 EF1400-M10 M10 200 EF1400-M12 M12 100 FINISH: ZINC PLATED NOTE: U BOLT NOT INCLUDED, ORDER SEPARATELY 149
FIRE PROTECTION PRODUCTS EF2100 EF2200 EF2300 FM127SP FINISH: GALVANISED EF2100 H.D. BOLTED CLIP PART NO PIPE DIA. D MATERIAL BOLT & NUT BAG QTY EF2100-060 50nb 60 40 x 6 M12 x 45 10 EF2100-076 65nb 76 40 x 6 M12 x 45 10 EF2100-089 80nb 89 40 x 6 M12 x 45 10 EF2100-115 100nb 115 40 x 6 M12 x 45 10 EF2100-140 125nb 140 40 x 6 M12 x 45 5 EF2100-168 150nb 168 40 x 6 M12 x 45 5 EF2100-220 200nb 220 40 x 6 M12 x 45 5 EF2200 PURLIN CLIP H.D. BOX QTY: 25 EF2300 PURLIN CLIP L.D. PART NO. HOLE DIA. BOX QTY EF2300-M8 M8 100 EF2300-M10 M10 100 FINISH: ZINC PLATED FINISH: GALVABOND FM127 SP WRAP AROUND BANDS PART NO. PIPE DIA. D MATERIAL HOLE SIZE BOX QTY FM127SP-027 20nb 27 25 x 1.0 11mm 100 FM127SP-034 25nb 34 25 x 1.0 11mm 100 FM127SP-043 32nb 43 25 x 1.2 11mm 50 FM127SP-048 40nb 48 25 x 1.2 11mm 50 FM127SP-060 50nb 60 25 x 1.2 11mm 50 FINISH: ZINC PLATED 150
NEMA 12B NEMA 16A NEMA 20B CABLE LADDER 300mm H W NEMA 12B CABLE LADDER PART NO WIDTH (W) HEIGHT (H) NEMA12B - 150 150mm 65mm NEMA12B - 300 300mm 65mm NEMA12B - 450 450mm 65mm NEMA12B - 600 600mm 65mm NEMA 16A CABLE LADDER PART NO WIDTH (W) HEIGHT (H) NEMA16A - 150 150mm 93mm NEMA16A - 300 300mm 93mm NEMA16A - 450 450mm 93mm NEMA16A - 600 600mm 93mm NEMA 20B CABLE LADDER PART NO WIDTH (W) HEIGHT (H) NEMA20B - 150 150mm 130mm NEMA20B - 300 300mm 130mm NEMA20B - 450 450mm 130mm NEMA20B - 600 600mm 130mm STANDARD LENGTH 6MTS FINISH GALVANISED. OTHER FINISHES AVAILABLE ON REQUEST ALL ACCESSORIES AVAILABLE 151
PERFORATED CABLE TRAY PCT H W PERFORATED CABLE TRAY PART NO WIDTH (W) HEIGHT (H) PCT - 75 75mm 10mm PCT - 100 100mm 10mm PCT - 150 150mm 10mm PCT - 225 225mm 10mm PCT - 300 300mm 10mm PCT - 450 450mm 10mm PCT - 600 600mm 10mm STANDARD LENGTH 2.4MTS FINISH GALVABOND. OTHER FINISHES AVAILABLE ON REQUEST ALL ACCESSORIES AVAILABLE 152
FT3 FT-COV FLEXI TRAY - LADDER TRAY H W LADDER TRAY PART NO WIDTH (W) HEIGHT (H) FT3-150 172 mm 50 mm FT3-300 322 mm 50 mm FT3-450 472 mm 50 mm FT3-600 622 mm 50mm STANDARD LENGTH 3MTS FINISH GALVABOND AND GALVANISED FLEXISTRUT COVER TRAY PART NO. FT-COV150 FT-COV300 FT-COV450 FT-COV600 TO SUIT 150mm TRAY 300mm TRAY 450mm TRAY 600mm TRAY STANDARD LENGTH 3MTS FINISH GALVABOND AND GALVANISED 153
LADDER TRAY - ACCESSORIES FT3 - HDC FLEXISTRUT TRAY HOLD DOWN CLAMP USED FOR SECURING TRAY ONTO SUPPORT. FINISH: GALVABOND AND GALVANISED FT3 - HDC FT3 - BS FM 156 FM 158 FT3 - BS FLEXISTRUT TRAY BARRIER STRIP FINISH: GALVABOND AND GALVANISED ADJUSTABLE CABLE DIVIDER LENGTH: 3MT FM156 CANTILEVER BRACKET PART NO. A FM156-200 200 FM156-350 350 FM156-500 500 FM156-650 650 FM156-750 750 FM158 CANTILEVER BRACKET PART NO. A FM158-200 200 FM158-350 350 FM158-500 500 FM158-650 650 FM158-780 780 FINISH: GALVANISED 154
FT3 - LP FT3 - FP FT3 - RP FT - B FT - N FT3 - LP LADDER TRAY - ACCESSORIES FLEXISTRUT LINK PLATE CREATE EXTERNAL AND INTERNAL RISERS TO RUN CABLE TRAY VERTICALLY. 6 LINK PLATES REQUIRED TO MAKE A 90 DEGREE RISER. FINISH: GALVABOND AND GALVANISED FT3 - FP FLEXISTRUT TRAY FISH PLATE JOINS STRAIGHT TRAY SECTIONS TOGETHER 2 FISH PLATES REQUIRED PER LENGTH. FINISH: GALVABOND AND GALVANISED FT3 - RP FLEXISTRUT RADIUS PLATE CREATES BENDS OF VARYING ANGLES. FINISH: GALVABOND AND GALVANISED LENGTH: 3MT FLEXISTRUT TRAY BOLTS AND NUTS. FOR SECURING LINK PLATE, FISH PLATE, RADIUS PLATE, T-X BRACKET AND HOLD DOWN CLAMP. FINISH: ZINC PLATED FT - B FT- N 155
LADDER TRAY - ACCESSORIES FT - TS FT3 - TX TRAPEZE SUPPORT PART NO WIDTH (W) FT - TS150 250 FT - TS300 400 FT - TS450 550 FT - TS600 700 FT - TS FINISH: GALVABOND AND GALVANISED FT3 - TX FLEXISTRUT TRAY T - X BRACKET USED FOR T OR CROSS INTERSECTION. (SEE ACROSS) FINISH: GALVABOND AND GALVANISED 156
FTF FQF FM2377 ELECTRICAL FITTINGS W H cable dia. 9mm hole FINISH: GALVABOND GALVANISED ON REQUEST TRIFOIL CLAMP PART NO CABLE DIA. WIDTH (W) HEIGHT (H) FTF - 20 20 92 43 FTF - 22 22 96 47 FTF - 24 24 100 51 FTF - 27 27 106 56 FTF - 30 30 112 62 FTF - 33 33 118 68 FTF - 37 37 126 75 FTF - 41 41 134 83 FTF - 45 45 142 90 W H cable dia. 9mm hole FINISH: GALVABOND GALVANISED ON REQUEST QUADFOIL CLAMP PART NO CABLE DIA. WIDTH (W) HEIGHT (H) FQF - 20 20 92 46 FQF - 22 22 96 50 FQF - 24 24 100 54 FQF - 27 27 106 60 FQF - 30 30 112 66 FQF - 33 33 118 72 FQF - 37 37 126 80 FQF - 41 41 134 88 FQF - 45 45 142 96 FM2377 CHANNEL JOINER L/DUTY USED FOR JOINING CHANNEL TOGETHER FM1000 AND FM2000. COMES WITH FOUR 7mm HOLES. FINISH: GALVABOND ORDER SEPERATELY FM3016 AND M6x15 COUNTERSUNK HEAD SCREWS. 157
ELECTRICAL FITTINGS FMC FMCR FMC BEAM CLAMP For suspension or direct attachment and installation of services, conduits, cables, threaded rods, chains etc. Used in combination with FMCR clips for conduits Used in combination with SM nut for threaded rods For beam flanges up to 45mm thickness Clamps are serrated for increased security SM nut FMC BEAM CLAMP PART NO A Bolt Size FMC20 20 6x25 FMC30 30 8x30 FMC45 45 8x30 FMCR CLIP For securing conduits or cables FMCR clip fits directly into the FMC beam clamp FMCR CLIP PART NO C B FMCR17 16-20 16 FMCR21 20.4-25 16 FMCR28 26.9-31.8 16 FMCR37 33.7-38 20 FMCR42 40-44.5 20 FMCR48 47-51 20 FMCR60 59.2-63.5 20 C FINISHED: GALVANISED 158