1 of 18 2/28/2008 10:41 AM Last Modified: 2-12-2007 Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2008 Model: xb Doc ID: RM000001XUW004X Title: INTERIOR: ROOF HEADLINING: REMOVAL (2008 xb) REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working. 2. REMOVE REAR FLOOR CARPET ASSEMBLY (a) Release the 2 knobs and remove the rear floor carpet. 3. REMOVE REAR DECK FLOOR BOX (a) Remove the rear deck floor box. 4. REMOVE DECK FLOOR BOX RH
2 of 18 2/28/2008 10:41 AM (a) Remove the 2 nuts and remove the deck floor box. 5. REMOVE DECK FLOOR BOX LH (a) Remove the 2 nuts and remove the deck floor box. 6. REMOVE REAR SEAT CUSHION WITH COVER PAD SUB-ASSEMBLY 7. REMOVE REAR SEATBACK ASSEMBLY RH 8. REMOVE REAR SEATBACK ASSEMBLY LH 9. REMOVE FRONT DOOR SCUFF PLATE RH (a) Disengage the 10 claws and remove the front door scuff plate. 10. REMOVE FRONT DOOR SCUFF PLATE LH
3 of 18 2/28/2008 10:41 AM 11. REMOVE COWL SIDE TRIM BOARD RH (a) Disengage the clip, claw and guide and remove the cowl side trim board. 12. REMOVE COWL SIDE TRIM BOARD LH 13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (a) Remove the front door opening trim weatherstrip. 14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 15. REMOVE REAR DOOR SCUFF PLATE RH
4 of 18 2/28/2008 10:41 AM (a) Disengage the 8 claws and remove the rear door scuff plate. 16. REMOVE REAR DOOR SCUFF PLATE LH 17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH (a) Remove the rear door opening trim weatherstrip. 18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 19. REMOVE REAR DECK TRIM COVER (a) Disengage the 4 clips, 4 claws and 2 guides and remove the rear deck trim cover.
5 of 18 2/28/2008 10:41 AM 20. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY Use the same procedure for both sides. (a) Remove the 2 bolts and 2 luggage hold belt strikers. 21. REMOVE REAR SEAT BACK HINGE Use the same procedure for both sides. (a) Remove the bolt and rear seat back hinge. 22. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (a) Remove the belt from the rear seat shoulder belt hanger. (b) Remove the bolt and floor anchor. 23. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
6 of 18 2/28/2008 10:41 AM 24. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (a) Using a clip remover, remove the clip. (b) Disengage the 6 clips and 7 claws and remove the deck trim side panel. 25. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (a) Using a clip remover, remove the clip. (b) Disengage the 6 clips and 7 claws and remove the deck trim side panel. (c) Disconnect the luggage compartment light connector.
7 of 18 2/28/2008 10:41 AM 26. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (a) Using a clip remover, remove the clip. (b) Disengage the 7 clips and remove the roof side inner garnish. (c) Pass the rear seat outer belt through the slit in the roof side inner garnish. 27. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH 28. REMOVE SEAT BELT ANCHOR COVER CAP Use the same procedure for both sides. (a) Pull portion A, shown in the illustration, toward you, remove the 2 claws on the lower side followed by the claw on the upper side. Then remove the seat belt anchor cover cap. 29. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH
8 of 18 2/28/2008 10:41 AM (a) Remove the bolt and through anchor. 30. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH 31. REMOVE CENTER PILLAR LOWER GARNISH RH (a) Disengage the 2 clips, 3 claws and guide and remove the center pillar lower garnish. 32. REMOVE CENTER PILLAR LOWER GARNISH LH 33. REMOVE CENTER PILLAR UPPER GARNISH RH (a) Disengage the 2 clips and guide and remove the center pillar upper garnish.
9 of 18 2/28/2008 10:41 AM 34. REMOVE CENTER PILLAR UPPER GARNISH LH 35. REMOVE FRONT PILLAR GARNISH RH NOTICE: Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed. Replace the front pillar garnish clip with a new one when the front pillar garnish is removed. (a) Disengage the 2 clips and 2 guides and remove the front pillar garnish. (b) Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the protective cover with adhesive tape, as shown in the illustration. Protective cover size: AREA MEASUREMENT a b 700 mm (27.56 in.) 120 mm (4.72 in.) 36. REMOVE FRONT PILLAR GARNISH LH
10 of 18 2/28/2008 10:41 AM 37. REMOVE ASSIST GRIP Use the same procedure to remove all assist grips. (a) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 assist grip covers. (b) Disengage the 2 clips and remove the assist grip. 38. REMOVE VISOR ASSEMBLY RH (a) Using a screwdriver, with its tip wrapped in protective tape, disengage the 4 claws and remove the visor cover.
11 of 18 2/28/2008 10:41 AM (b) Remove the visor shaft from the visor holder. (c) Disengage the 2 clips and remove the visor. 39. REMOVE VISOR ASSEMBLY LH 40. REMOVE VISOR HOLDER (a) Turn the visor holder approximately 45 and pull it out as shown in the illustration. (b) Disengage the 2 claws and remove the visor holder. 41. REMOVE ROOM LIGHT ASSEMBLY
12 of 18 2/28/2008 10:41 AM (a) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens. (b) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 room light covers. (c) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.
13 of 18 2/28/2008 10:41 AM (d) Remove the roof wire from the claw on the room light. (e) Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base. 42. REMOVE MAP LIGHT ASSEMBLY (a) Using a moulding remover, disengage the 4 claws and remove the map light. (b) Disconnect the map light connector. 43. REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY 44. REMOVE INSTRUMENT CLUSTER FINISH LOWER PANEL 45. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY 46. REMOVE COMBINATION METER ASSEMBLY
14 of 18 2/28/2008 10:41 AM 47. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY 48. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY 49. REMOVE ROOF HEADLINING (a) Disconnect the antenna cord connector. (b) Using a clip remover, disengage the 4 clamps. (c) Disconnect the roof wire connector. (d) Disconnect the roof wire from the harness clamp. (e) Using a clip remover, disengage the 5 clamps.
15 of 18 2/28/2008 10:41 AM (f) Disconnect the 2 connectors. (g) Remove the bolt and bracket. (h) Using a clip remover, remove the 5 clips. (i) Remove the roof headlining from the back door. 50. REMOVE NO. 1 ROOF SILENCER (a) Remove the 2 No. 1 roof silencers. 51. REMOVE NO. 3 ROOF PANEL PAD
16 of 18 2/28/2008 10:41 AM (a) Remove the No. 3 roof panel pad. 52. REMOVE NO. 4 ROOF PANEL PAD (a) Remove the No. 4 roof panel pad. 53. REMOVE NO. 1 ROOF SILENCER PAD (a) Remove the 5 No. 1 roof silencer pads. 54. REMOVE ROOF HEADLINING PAD RH
17 of 18 2/28/2008 10:41 AM (a) Remove the 8 adhesive portions and the roof headlining pad. 55. REMOVE ROOF HEADLINING PAD LH (a) Remove the 8 adhesive portions and the roof headlining pad. 56. REMOVE FRONT SIDE RAIL SPACER RH (a) Remove the 2 adhesive portions and the front side rail spacer. 57. REMOVE FRONT SIDE RAIL SPACER LH 58. REMOVE ROOF WIRE
18 of 18 2/28/2008 10:41 AM (a) Remove the 10 pieces of tape. (b) Remove the roof wire from the roof headlining. 59. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY