623CT MOBILE IMPACT CRUSHER with CAT C9-T3 Engine TECHNICAL SPECIFICATION Subject to change without notice.
DESCRIPTION: Self Contained Mobile Impact Crusher with the following features: 275Hp CAT C9 Tier III Diesel Engine. Heavy Duty Horizontal Shaft Rotor. 600mm x 350mm (23 x 14 ) Crusher Feed Opening. Hydraulically Adjustable Bar Carrier. Hydraulically Opening Crusher Body. IBF 314 Clutch (Optional Transfluid 19 KPTO Hydraulic Clutch). 800mm (32 ) Wide Hydraulically Folding Feed Conveyor Belt. 650mm (26 ) Wide Hydraulically Folding Product Conveyor Belt. Feed and Product Conveyor Variable Speed Controls. 400mm Wide Crawler Tracks. Large Feed Hopper. Dust Suppression on Crusher Feed-in and feed-out. Fast on Site setup Time 15 Minutes. DIMENSIONS AND WEIGHT: Length Transport: - 15m (49 2 ) Length Working: - 16.13m (52 11 ) Width Transport: - 2.9m (9 6 ) Width Working: - 2.9m (9 6 ) Height Transport: - 3.4m (11 1 ) Weight Estimated: - 27,000 Kgs (59,525 Lbs) NOTE: The weights and dimensions stated here are given for a standard machine only. Optional extras fitted to the machine and/or transportation laws in force in various countries, may alter the transportation weight and dimensions of the machine. Page 2
HOPPER: Hopper Length (with shroud): - 4310mm (14 1 ) Hopper Width (with shroud): - 1830mm (6 ) Hopper Capacity: - 6m 3 (7.85yd 3 ) Shroud: - YES Feed in Height: - 3.8m (12 5 ) FEED CONVEYOR: Belt Width: - 800mm (32 ) Belt Spec: - Plain EP500/3 5+1.5 Drive Drum Dia: - 220mm (8 ) Tail Drum Dia: - 220mm (8 ) Gearbox: - Brevini Gearbox Ratio: - 1:18 Gearbox Torque: - 3500 Nm cont Motor: - 130cc Max Flow Rate: - 119 Lpm (31.44 US Gpm) Variable Speed Control: - YES Belt Speed: - Factory set @ 27 M/min CRUSHER: Feed Opening: - 600mm x 350mm (23 x 14 ) Maximum Crusher Speed: - 650 Rpm Minimum Crusher Setting: - 10mm (0.4 ) Maximum Crusher Setting: - 60mm (2.4 ) Maximum Feed Size: - 200mm (8 ) Crusher Drive Required: - Direct Drive SPC V-Belts 6off Rotor Size: - 600mm (22.6 ) wide x 1068mm (42 ) Dia. Pulley Size: - SPC 700, 6 Groove Hammers: - 3 off Bar Carrier: - 4 Bar Wear Plate Thickness: - 30mm Hydraulic Bar Carrier Adjustment: - YES Hydraulic Crusher Body Opening: - YES Hydraulic Crusher Adjustment: - YES (Bar Carrier) Page 3
MAIN PRODUCT CONVEYOR: ELECTRICS POWER UNIT AND HYDRAULICS: Discharge Height: - 3690mm (12 1 ) Belt Width: - 650mm (26 ) Belt Spec: - Plain EP500/3 5+1.5 Drive Drum Dia: - 220mm (8 ) Tail Drum Dia: - 220mm (8 ) Motor: - 625cc Max Flow Rate: - 119Lpm (31.44 US Gpm) Variable Speed Control: - YES Belt Speed : - Factory set @ 105 M/min Chassis Cabling: - SWA Cable Emergency Stops: - 5 off, 1 @ Control Console RH Side 2 @ Rear Chassis LH & RH Sides 2 @ Front Chassis LH & RH Sides Start Siren: - YES 10 Second Delay Warning Beacon: - YES Tracking Siren: - YES 10 Second Delay Tracking Beacon: - YES Engine Shutdowns: - Low Oil Pressure - High Water Temp - Air Filter Blockage - Fuel Contamination Crusher Shutdowns: - Clutch Oil Temperature Radio Control Tracks: - OPTIONAL (Hetronic) Pendant Track control: - YES Engine: - CAT C9 TA (TIER III) Engine Power: - 205Kw - 275 HP Engine Speed: - 1800 Rpm Main Flywheel Pump: - DBH 50512off Clutch: - IBF 314 ( Optional Transfluid 19 KPTO) Crusher Drive Pulley: - SPC 250 x 6 Diesel Tank Capacity: - 500 Ltrs (110 US Gal) Hydraulic Tank Capacity: - 700 Ltrs (154 US Gal) Hydraulic Oil Cooler: - YES Hydraulic Clutch Oil Cooler: - YES Page 4
FUEL PERFORMANCE: The fuel consumption rates above are estimated using the BSFC values quoted on the engine performance charts for each model - please note that this value is only accurate at the 100% load figure quoted on this chart. Page 5
TRACKS: Gearbox: - RRTD3600 Ratio: - 161:1 Width: - 400mm (15.8 ) Length (overall): - 3960mm (13 ) Height: - 740mm (29 ) Motor: - MSI163cc Speed max: - 1.3 Kph (0.81 Mph) Flow Rate: - 120 Lpm (31.7 US Gpm) Gradeability: - 40.9 Max slope side to side: - 10 Attachment to Chassis: - Bolt On SAFETY FEATURES: Engine Safety Shutdown Systems Full Safety Guarding for Nip Points Key Switch Operated Tracking System 10 Second Start and Tracking Delays Easy Access Lubrication Points CE Compliance OPTIONS:. 19 KPTO Clutch Metal Detector Picking Platform Autolub System Hydraulic Tipping Grid Remote Control Tipping Grid Manual Tipping Grid Closed Circuit Conveyor Product Conveyor Screenbox Product Conveyor Magnet Scales Radio Remote Control for Tracks Conveyor Dust Covers Working Lights 68 Type Hydraulic Oil E-Stop Pull Wires NOTE: Fitting optional extras to this machine may increase the manufacturing lead time. Page 6
WORKING DIMENIONS: Page 7
SIEVE ANALYSIS: Page 8
NOISE LEVELS: Page 9