½ -1½ - Pressure Independent ontrol Valve - Modulating control valve, dynamic balancing valve and differential pressure control valve in one body. Field adjustable, self-balancing, dynamic flow control valves that are pressure independent, two-way and modulating to accept analog signal inputs. Each valve has an adjustable maximum flow rate setting to enable flow limitation and balancing to the coil or zone that the valve is controlling. dvantages of ray TT Valves - 1. Installation costs - up to 60% fewer valves are required. Due to the automatic balancing of each heat exchanger, no other differential pressure control valves or balancing valves are required. This simplifies installation, reduces installed costs, and improves accuracy and reliability. 2. Operating costs - Minimizes pumping, heating and cooling costs by eliminating overflow through the coil and by reducing pressure drop. 3. The location of the ray TT automatic balancing valve does not require lengths of pipe before or after the valve. ody Style & D TT Series djustable PI Valves 2 Way 1/2-1-1/2 TT - utotouch Terminal ody Style - System Types: - Media: Fan oil, VV Reheat oils, ot Water, hilled Water, hilled eams and ir andling Units 50/50 Glycol Solutions. 11/13/13 Features and enefits Field djustable, up to 41 different flow rates in one and the same cartridge Flow rate can be changed on demand without removing the cartridge from the valve body 100% uthority Pressure Independent The valve will always use full stroke of the control element offering the 100% authority for any of its 41 flow settings uilt-in Isolation all Valve (ody Style and D) llows for coil isolation Female-by-Female Threaded (ody Style ) Double Union End onnection, Threaded or Sweat (ody Style and D) For ease of installation and wide selection of end fittings Optional Pressure/Temperature Measurement Ports llows for verifying operating differential pressure across the valve TT-1
TT - Valve Specifications ody Style,, D 1/2 1-1/2 Technical Specifications Service Valve ody Pressure Rating lose-off Pressure Operational P Operational P Flow Rate Range Leakage End onnections mbient Temperature Rating Minimum Media Temperature Rating Water Maximum Minimum Maximum ot Water, hilled Water, 50/50 Glycol Solutions Pressure rating: 360 psi / (25 ar) (L & M artridge) 87 psid / (6 ar) ( artridge) 58 psid / (4 ar) (L artridge) 2.3 psid / (0.16 ar) (M artridge) 4.4 psid / (0.3 ar) ( artridge) 2.3 psid / (0.16 ar) 58 psid / (4 ar) (L artridge) 0.1 to 3.3 GPM, (32.0 to 757 L/hr) (M artridge) 0.3 to 4.9 GPM, (64 to 1110 L/hr) ( artridge) 3.8 to 20.4 GPM, (865 to 4630 L/hr) NSI / FI 70-2 2006 (R1982) / IE 60534-4 lass - lass IV- < 0.01% (ody Only) Fixed female NPT or SP, or Sweat (ody, D Only) Union End onnection in rass lloy, NPT or SP 34 to 122 F (1 to 50 ) -4 F (-20 ) Maximum Media Temperature Rating 212 F (100 ) TT ody Style 248 F (120 ) TT ody Style, D Materials Weights (lbs.) artridge Diaphragm ody all Valve (ody, D Only) Union End onnections O-Rings Valve ody Only POM (Polyoxymethylene) - with Stainless Steel trim ydrogenated crylonitrile-utadiene-rubber Forged rass STM uzn40pb2 hemically Nickel Plated rass all rass alloy NPT (ody Style & D only) EPDM 1/2 (ody ) 1.2lb., 0.55kg 3/4 (ody ) 1.3lb., 0.59kg 1 (SP Only) (ody ) 1.4lb., 0.64kg 1 (ody ) 4.1lb., 1.86kg. 1-1/4 (ody ) 3.7lb., 1.68kg 1/2 1 (ody ) 1.9lb., 0.87kg 1 1-1/2 (ody D) 4.7lb., 2.14kg Disclaimer - The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications, consult the local ray office. ray, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. TT-2
TT - ctuator Specifications TT ctuators FN.0.2 FN.0.4 FN.1.2 Supply voltage 24V /D ±10%, 50/60 z Motor i-directional synchronous Power consumption 3V 3V 3V, 5V peaks Input Impedance >30kΩ - >30kΩ ontrol signal Digital nalog 0(2)-10V D (2-position / 3-point floating) nalog 0(2)-10V D Position output 0(2)-10V D - 0(2)-10V D Failsafe function No No Yes uto stroke Yes No Yes Operation time 50 z: 90 seconds 50 z: 90 Seconds 50 z: 45 Seconds ctuation force 50 lbf, 225N ±5% 50 lbf, 225N ±5% 50 lbf, 225N ±5% mbient temperature -0.4 F to +122 F umidity rating <95% Non ondensing Protection IP54, class II able 4 wires 22 WG halogen free cable, 3.2 feet 3 wires 22 WG halogen free cable, 3.2 feet 4 wires 22 WG halogen free cable, 3.2 feet Weight 0.55 lbs 0.55 lbs 0.66 lbs FN.0.2 & FN.0.4 Series FN.1.2 Series uto Stroke Option With the auto stroke option activated, the actuator will make one full cycle every 24 hours, if the actuator constantly has been in fully open or fully closed position during the previous 24 hours. This operation will clear up any possible impurities accumulated in the valve, and re-calculate the end positions. TT-3
TT - Piping Diagrams Shown with Optional PT Ports RETURN RETURN OIL OIL SUPPLY SUPPLY Notes: Valve diameter should Never exceed pipe diameter Mount the TT valves to the return side of the coil. 20 mesh strainer should be installed on the supply side of each coil using the TT valve. TT - ctuator Wiring FN.0.4 Series ctuator FN.0.4 ctuator 2-Position, Normally losed FN.0.4 ctuator 2-Position, Normally Open lack lack lose Open Open lose Power 24V /D Power 24V /D FN.0.4 ctuator 3-Point-Floating, Normally losed FN.0.4 ctuator 3-Point-Floating, Normally Open lack lose Stop Open lack Open Stop lose Power 24V /D Power 24V /D FN.0.2 & FN.1.2 Series ctuators FN.0.2 / FN.1.2 ctuator lack Input signal 0(2)-10V D Green Feedback signal 0(2)-10V D Power 24V /D TT-4
TT - Valve/ctuator Dimensions Model Number TT--050-X-X/ct. TT--075-X-X/ct. TT--100-X-X/ct. TT--100-X-X/ct. TT--125-X-X/ct. TT--050-X-X/ct. TT--075-X-X/ct. TT--100-X-X/ct. TT-D-100-X-X/ct. TT-D-125-X-X/ct. TT-D-150-X-X/ct. Valve Model D Valve Size artridge Size Note * dd end connection length to body length. Note ** Weight does not include end connections or actuator. Note *** For valve body. (FN.0.4 & FN.0.2) D (FN.1.2) End connections E NPT female NPT male Sweat F ody Tappings 1/2 3.23 1.2 3/4 L & M 3.70 1.22 5.12 5.71 N/ N/ N/ 1.3 (3/4 dia.) 1 SP Only 4.02 1/4 1.4 1 4.1 (1-1/2 dia.) 5.04 1.85 6.02 6.50 N/ N/ N/ 1 1/4 3.7 1/2 0.87 0.99 0.79 3/4 L & M (3/4 dia.) 4.80 1.30 5.12 5.71 0.87 0.99 0.79 1 N/ 1.54 0.87 1 1.38 1.57 1.34 1 1/4 (1-1/2 dia.) 6.61 1.62 6.02 6.50 1.38 1.57 1.46 1 1/2 1.57 1.65 N/ 1/4 1/4 Weight** v *** (lbs.) (GPM) 3.0 14.5 1.9 3.0 4.7 14.5 F F F, D, D, D Valve model: Shown with FN.0.4, FN.0.2 ctuator Valve model:, D Shown with FN.0.4, FN.0.2 ctuator E Valve model:, D Shown with FN.1.2 ctuator E TT - Strainer Dimensions onnection in. mm 1/2 15 3.9 1.1 2.3 3/4 20 3.9 1.1 2.3 1 25 5.3 1.3 2.6 1 1/4 32 7.7 1.9 3.7 1 1/2 40 7.5 1.9 3.7 2 50 9.5 1.6 4.3 Dimensions may vary, depending on the actuator. Dimensions are shown for the largest spring return actuator currently available. Dimensions are shown in inches and are approximate. TT-5
TT - ow it Works Dynamic Flow Rate Limiter djustment The utotouch Terminal (TT) is set to 1 of 41 settings of maximum flows with the adjustment key. Turn the adjustment key to numerals 1 through 5 with the decimals appearing in red. Flow Rate can be changed on demand without removing the cartridge from the valve body. Flow Flow artridge djustment with Key Rotates with Key to adjust Flow Principle of Operation The function of the TT valve is best described as three functions in one. The first valve regulates the pressure differential across the second valve by means of a rolling diaphragm element counteracted by a spring. The second valve is a calibrated variable orifice device adjusted by the actuator (similar to a standard modulating control valve). Dynamic alancing of Flow The diaphragm reacts to the system and regulates the pressure differential across the actuated control valve orifice to maintain its flow rate. Go to the following web address to see a video demonstration: www. braycommercialdivision. com/att.mov Indicates Flow Direction Indicates Pressure hanges Full Stroke Modulation 100% authority guaranteed. hanging the setting will not affect the stem height as the setting merely turns the inner bottom part of the cartridge sideways. t any setting the stem height will remain the same providing full stroke. TT-6
TT - Flow Rate Table micrometer setting of 3.4 as illustrated above corresponds to a max flow rate of: 2.6 GPM - (L) artridge 4.1 GPM - (M) artridge 15.5 GPM - () artridge Use the special designed key for micrometer setting. Key O-Ring O-Ring (L) artridge (M) artridge () artridge 2.3-29 psid (.16-2 bar) Low Flow (Green O-Ring) 4.4-58 psid (.30-4 bar) Medium Flow (lack O-Ring) 2.3-58 psid (.16-4 bar)* igh Flow (lack O-Ring) SETTING GPM l/hr GPM l/hr GPM l/hr 1 0.1 32.0 0.3 64 3.8 865 1.1 0.3 75.8 0.6 142 4.5 1010 1.2 0.5 116 0.9 209 5.1 1160 1.3 0.7 153 1.2 268 5.7 1300 1.4 0.8 188 1.4 319 6.3 1430 1.5 1.0 220 1.6 366 6.9 1570 1.6 1.1 250 1.8 408 7.5 1700 1.7 1.2 278 2.0 446 8.0 1820 1.8 1.3 304 2.1 482 8.6 1940 1.9 1.5 329 2.3 516 9.1 2060 2.0 1.6 352 2.4 549 9.6 2180 2.1 1.7 374 2.6 580 10.1 2290 2.2 1.7 396 2.7 611 10.6 2400 2.3 1.8 416 2.8 641 11.0 2510 2.4 1.9 435 3.0 671 11.5 2610 2.5 2.0 453 3.1 700 11.9 2710 2.6 2.1 471 3.2 728 12.4 2810 2.7 2.2 488 3.3 756 12.8 2900 2.8 2.2 504 3.5 783 13.2 3000 2.9 2.3 520 3.6 810 13.6 3090 3.0 2.4 535 3.7 835 14.0 3180 3.1 2.4 549 3.8 860 14.4 3260 3.2 2.5 563 3.9 883 14.7 3350 3.3 2.5 577 4.0 906 15.1 3430 3.4 2.6 590 4.1 927 15.5 3510 3.5 2.7 602 4.2 946 15.8 3590 3.6 2.7 614 4.3 965 16.1 3670 3.7 2.8 626 4.3 982 16.5 3740 3.8 2.8 637 4.4 998 16.8 3820 3.9 2.9 649 4.5 1010 17.1 3890 4.0 2.9 659 4.5 1020 17.4 3960 4.1 3.0 670 4.6 1040 17.7 4030 4.2 3.0 681 4.6 1050 18.1 4100 4.3 3.0 691 4.7 1060 18.4 4170 4.4 3.1 701 4.7 1070 18.7 4240 4.5 3.1 711 4.7 1080 19.0 4300 4.6 3.2 721 4.8 1080 19.2 4370 4.7 3.2 730 4.8 1090 19.5 4440 4.8 3.3 740 4.8 1100 19.8 4500 4.9 3.3 749 4.9 1100 20.1 4570 5.0 3.3 757 4.9 1110 20.4 4630 ccuracy: Greatest of either +/- 10% of controlled flow rate or +/- 5% of maximum flow rate. * t setting 2.6 TT-7
TT - Model Number ody Style (see body style configuration chart below) Valve Size artridge Flow Rate onnection/ Port ode ctuator Sample Part Number TT STYLE Sizes (in/(mm)) Isolation all Valve artridge 1/2(15), 3/4(20), - 1(25) 1(25), 1-1/4(32) - D 1/2(15), 3/4(20), 1(25), 1 1/4(32) 1(25), 1-1/4(32), 1-1/2(40) 050 SIZE in. mm 050 1/2 15 075 3/4 20 100 1 25 125 1-1/4 32 150 1-1/2 40 ODE Pressure range, P(psi) Flow rate(gpm) L Low Flow 2.3-29 psi,.16-2 bar 0.141-3.31 M Medium Flow 4.4-58 psi,.30-4 bar 0.282-4.89 igh Flow 2.3-58 psi,.16-4 bar 3.81-20.4 0.1 to 20.4 ODE Description NF NPT female threads NFP NPT female threads with pressure/temperature plugs NM NPT male threads NMP NPT male threads with pressure/temperature plugs SW Sweat termination SWP Sweat termination with pressure/temperature plugs F SP female threads FP SP female threads with pressure/temperature plugs M SP male threads MP SP male threads with pressure/temperature plugs FN.0.2 24V Modulating FN.0.4 24V 3-Point Floating FN.1.2 24V Modulating (with feedback signal) M 2.4 Reference the previously listed Flow Rate Table and select the desired flow rate GPM that is listed for the cartridge that you are using. *Example: Medium Flow artridge, 1/2", body style, 2.4 GPM, Female NPT with PT ports with FN.0 actuator TT--050-M-2.4-NFP/FN.02 dditional Example: igh Flow artridge, 32mm, body style D, 1300 l/hr, male SP threads with PT ports. TT-D-125--5.7-MP/FN.02 NFP See ody Style onfiguration hart elow (Union Ends standard on ody & D) FN.0.2 ody Style onfigurations Sizes (in. mm) 1/2 (15), 3/4 (20) 1(25)* 1 (25), 1-1/4 (32) 1/2 (15), 3/4 (20) artridge ody Type NPT Male NPT Female SP Male SP Female Sweat Union Ends Pressure/ Temp Ports Isolation all Valve 1 (25) 1 (25), 1-1/4 (32), 1-1/2 (40) * 1 utilizing the L & M cartridge available as SP only D TT-8